Senco PC 1010 Manuel utilisateur
- Catégorie
- Compresseurs d'air
- Taper
- Manuel utilisateur
Ce manuel convient également à
1
Operating Instructions
Warnings for the safe use of this compressor are included in this manual.
Des mises en garde pour une utilisation en toute sécurité de ce compresseur
sont incluses dans ce manuel.
En este manual se incluyen avisos para el uso seguro de este compresor.
PC 1010
Electric Air Compressor
PC1010 Revised February 1, 2008
(Replaces 10/18/07)
Questions? Comments? call SENCO's toll-free Action-line: 1-800-543-4596 or e-mail: [email protected]
© 2002, 2008 by Senco Products, Inc.
Senco Products, Inc.
8485 Broadwell Rd.
Cincinnati, OH 45244
2
TABLE OF CONTENTS
INTRODUCTION ................................................................... 3
SAFETY INSTRUCTIONS...................................................... 3
INSPECTION ......................................................................... 3
SAFETY WARNINGS .........................................................4-7
ELECTRICAL................................................................ 4
EXPLOSION OR FIRE.................................................. 5
BURSTING ................................................................... 5
BREATHING ................................................................. 6
BURNS ......................................................................... 6
FLYING OBJECTS........................................................ 6
MOVING PARTS ........................................................... 7
NEGLIGENCE .............................................................. 7
AIR COMPRESSOR DAMAGE ..................................... 7
COMPRESSOR FEATURES ................................................. 8
PREPARATION .................................................................... 10
INITIAL SET-UP ......................................................... 10
LOCATION.................................................................. 10
ELECTRICAL.............................................................. 10
OPERATION ........................................................................ 11
PRE-START CHECKLIST........................................... 11
START-UP .................................................................. 11
SHUTDOWN .............................................................. 11
MAINTENANCE................................................................... 11
TROUBLESHOOTING ................................................... 12-13
SPECIFICATIONS ............................................................... 14
WARRANTY ........................................................................ 15
CALIFORNIA PROPOSITION 65 WARNING................ 7
PARTS CHART..................................................................... 16
3
INTRODUCTION
Congratulations on the purchase of your new SENCO® Air Compressor! You can be assured your SENCO Air
Compressor was constructed with the highest level of precision and accuracy. Each component has been rigorously
tested by technicians to ensure the quality, endurance and performance of this air compressor.
This operator’s manual was compiled for your benefit. By reading and following the simple safety, installation and
operation, and maintenance steps described in this manual, you will receive years of troublefree operation
from your new SENCO Air Compressor. . The contents of this manual are based on the latest product
information available at the time of publication. The manufacturer reserves the right to make changes in price,
color, materials equipment, specifications or models at any time without notice.
SAFETY ALERT!
A ”
DANGER, WARNING or CAUTION
” safety warning will be surrounded by a ”SAFETY ALERT BOX”.
This box is used to designate and emphasize Safety Warnings that must be followed when operating this
air compressor. Accompanying the safety warnings are “Signal Words” which designate the degree or
level of hazard seriousness. The “Signal Words” used in this manual are as follows:
DANGER:
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
WARNING:
Indicates an imminently hazardous situation which, if not avoided,
COULD result in death or serious injury.
CAUTION:
Indicates an imminently hazardous situation which, if not avoided
MAY result in minor or moderate injury or damage to the air
compressor.
The symbols set to the left of this paragraph are “Safety Alert Symbols”.
These symbols are used to call attention to items or procedures that could
be dangerous to you or other persons using this equipment.
ALWAYS PROVIDE A COPY OF THIS MANUAL TO ANYONE USING THIS EQUIPMENT. READ ALL
INSTRUCTIONS IN THIS MANUAL AND ANY INSTRUCTIONS SUPPLIED BY MANUFACTURERS OF
SUPPORTING EQUIPMENT BEFORE OPERATING THIS AIR COMPRESSOR AND ESPECIALLY POINT OUT
THE “SAFETY WARNINGS” TO PREVENT THE POSSIBILITY OF PERSONAL INJURY TO THE OPERATOR.
INSPECTION
Unbox the air compressor and write in the serial number in the space provided below. Inspect for signs of obvious
or concealed freight damage. Be sure that all damaged parts are replaced and any mechanical problems are
corrected prior to the operation of the air compressor.
SERIAL NUMBER__________________________________________
If you have Questions or Comments call SENCO’s toll-free Action-line: 1-800-543-4596 or, e-mail:
toolprof@Senco.com
Please have the following information available for all service calls:
1. Model Number
2. Serial Number
3. Date and Place of Purchase
Senco, 8485 Broadwell Road, Cincinnati, OH 45244
4
POTENTIAL CONSEQUENCE
Serious injury or death could occur if
the air compressor is not properly
grounded. Your air compressor is
powered by electricity and may cause
electric shock or electrocution if not
used properly.
Electrical shock may occur from
electrical cord.
Electrical shock may occur if air
compressor is not operated properly.
Serious injury or death may occur if
electrical repairs are attempted by
unqualified persons.
PREVENTION
Make sure the air compressor is
plugged into a properly grounded
outlet which provides correct
voltage and adequate fuse
protection.
Check power cord for signs of
crushing, cutting or heat damage.
Replace faulty cord before use.
Keep all connections dry and off the
ground. Do not allow electrical
cords to lay in water or in such a
position where water could come in
contact with them. Do not touch
plug with wet hands.
Do not pull on the electrical cord to
disconnect from the outlet.
Never operate air compressor in
wet conditions or outdoors when it
is raining.
Never operate air compressor with
safety guards/covers removed or
damaged.
Any electrical wiring or repairs
performed on this air compressor
should be done by Authorized
Service Personnel in accordance
with National and Local electrical
codes.
Before opening any electrical
enclosure, always shut off the air
compressor, relieve pressure and
unplug the air compressor from the
power source. Allow air compressor
to cool down. Never assume the air
compressor is safe to work on just
because it is not operating. It could
restart at any time!
HAZARD
RISK OF
ELECTRIC SHOCK
OR
ELECTROCUTION
SAFETY WARNINGS
READ ALL SAFETY WARNINGS BEFORE USING AIR COMPRESSOR
4
POTENTIAL CONSEQUENCE
Serious injury or death could occur if
the air compressor is not properly
grounded. Your air compressor is
powered by electricity and may cause
electric shock or electrocution if not
used properly.
Electrical shock may occur from
electrical cord.
Electrical shock may occur if air
compressor is not operated properly.
Serious injury or death may occur if
electrical repairs are attempted by
unqualified persons.
PREVENTION
Make sure the air compressor is
plugged into a properly grounded
outlet which provides correct
voltage and adequate fuse
protection.
Check power cord for signs of
crushing, cutting or heat damage.
Replace faulty cord before use.
Keep all connections dry and off the
ground. Do not allow electrical
cords to lay in water or in such a
position where water could come in
contact with them. Do not touch
plug with wet hands.
Do not pull on the electrical cord to
disconnect from the outlet.
Never operate air compressor in
wet conditions or outdoors when it
is raining.
Never operate air compressor with
safety guards/covers removed or
damaged.
Any electrical wiring or repairs
performed on this air compressor
should be done by Authorized
Service Personnel in accordance
with National and Local electrical
codes.
Before opening any electrical
enclosure, always shut off the air
compressor, relieve pressure and
unplug the air compressor from the
power source. Allow air compressor
to cool down. Never assume the air
compressor is safe to work on just
because it is not operating. It could
restart at any time!
HAZARD
RISK OF
ELECTRIC SHOCK
OR
ELECTROCUTION
SAFETY WARNINGS
READ ALL SAFETY WARNINGS BEFORE USING AIR COMPRESSOR
5
SAFETY WARNINGS
READ ALL SAFETY WARNINGS BEFORE USING AIR COMPRESSOR
POTENTIAL CONSEQUENCE
Serious injury or death may occur from
normal electrical sparks in motor and
pressure switch.
Serious injury may occur if any air
compressor ventilation openings are
restricted, causing the air compressor
to overheat and start on fire.
Serious injury or death may occur from
an air tank explosion if air tanks are
not properly maintained.
Serious injury may occur from an air
compressor malfunction or exploding
accessories if incorrect system
components, attachments or
accessories are used.
HAZARD
RISK OF
EXPLOSION OR FIRE
RISK OF
BURSTING
PREVENTION
Always operate air compressor in a
well ventilated area free of
flammable vapors, combustible
dust, gases or other combustible
materials.
If spraying flammable material,
locate the air compressor at least
20 feet away from the spray area.
(An additional hose may be
required.)
Never place objects against or on
top of air compressor. Operate air
compressor at least 12 inches away
from any wall or obstruction that
would restrict proper ventilation.
Drain air tank daily or after each use
to prevent moisture buildup in the
air tank.
If air tank develops a leak, replace
the air tank immediately. Never
repair, weld or make modifications
to the air tank or its attachments.
Never make adjustments to the
factory set pressures.
Never exceed manufacturers
maximum allowable pressure rating
of attachments.
Because of extreme heat, do not
use plastic pipe or lead tin soldered
joints for a discharge line.
Never use air compressor to inflate
small, low pressure objects such as
Use only genuine SENCO® repair
parts for your air compressor.
toys.
6
POTENTIAL CONSEQUENCE
Serious injury or death could occur
from inhaling compressed air. The air
stream may contain carbon monoxide,
toxic vapors or solid particles.
Sprayed materials such as paint, paint
solvents, paint remover, insecticides,
weed killers, etc. contain harmful
vapors and poisons.
Serious injury could occur from
touching exposed metal parts.
These areas can remain hot for some
time after the air compressor is
shutdown.
Soft tissue damage can occur from the
compressed air stream.
Serious injury can occur from loose
debris being propelled at a high speed
from the compressed air stream.
SAFETY WARNINGS
READ ALL SAFETY WARNINGS BEFORE USING AIR COMPRESSOR
HAZARD
RISK TO
BREATHING
RISK OF
BURNS
RISK
OF FLYING
OBJECTS
PREVENTION
Never inhale air from the air
compressor either directly or from a
breathing device connected to the air
compressor.
Operate air compressor only in a well
ventilated area. Follow all safety
instructions provided with the
materials you are spraying. Use of a
respirator may be required when
working with some materials.
Never allow any part of your body or
other materials to make contact with
any exposed metal parts on the air
compressor.
Always wear OSHA required “Z87”
safety glasses to shield the eyes
from flying debris.
Never point the air stream at any part
of your body, anyone else or animals.
Never leave pressurized air
compressor unattended. Shut off air
compressor and relieve pressure
before attempting maintenance,
attaching tools or accessories.
Always maintain a safe distance from
people and animals while operating
the air compressor.
Do not move the air compressor
while air tank is under pressure. Do
not attempt to move the air
compressor by pulling on the hose.
7
POTENTIAL CONSEQUENCE
Risk of bodily injury from moving parts.
This air compressor cycles
automatically when the pressure
switch is in the “On/Auto” position.
Risk of injury from negligent use.
Risk of major repair.
SAFETY WARNINGS
READ ALL SAFETY WARNINGS BEFORE USING AIR COMPRESSOR
RISK FROM
NEGLIGENCE
RISK
OF AIR COMPRESSOR
DAMAGE
HAZARD
RISK FROM
MOVING PARTS
PREVENTION
Always turn off air compressor.
Bleed pressure from the air hose
and unplug from electrical outlet
before performing maintenance.
All repairs to the air compressor
should be made by an Authorized
Service person. Never assume the
air compressor is safe to work on
just because it is not operating.
It could restart at any time!
Do not operate without protective
covers/guards. Replace damaged
covers/guards before using the air
compressor.
Never allow children or adolescents
to operate this air compressor!
Stay alert-watch what you are doing.
Do not operate the air compressor
when fatigued or under the influence
of alcohol or drugs.
Know how to stop the air
compressor. Be thoroughly familiar
with controls.
Do not operate air compressor
without an air filter.
Do not operate air compressor in a
corrosive environment.
Always operate the air compressor
in a stable, secure position to prevent
air compressor from falling.
Follow all maintenance instructions
listed in this manual.
! SAVE THESE INSTRUCTIONS !
Do not incline the air compressor
transversly or longitudinally more
than 10°.
8
COMPRESSOR FEATURES
1 Motor/Pressure Switch
2 Thermal Overload / Reset
3 Air Intake Filter
4 Air Compressor Pump
5 Safety Relief Valve
6 Air tank drain valve
7 Tank Pressure Gauge
8 Outlet Pressure Gauge
9 Pressure Regulator
10 Discharge Line
11 115 Volt Electric Power Cord
12 Ventilation Openings / Protective Shroud
13 Quick Disconnect
1
23
4
12
7
8
10
9
5
6 13
11
9
COMPRESSOR FEATURES
1) MOTOR/PRESSURE SWITCH: This switch is used to start or stop the air
compressor. Moving the switch to the (On) position will provide automatic
power to the pressure switch which will allow the motor to start when the air tank
pressure is below the factory set cut-in pressure. When in the (On) position,
the pressure switch stops the motor when the air tank pressure reaches the factory
set cut-out pressure. For safety purposes, this switch also has a pressure release
valve located on the side of the switch designed to automatically release compressed
air from the air compressor pump head and its discharge line when the air compressor
reaches cut-out pressure or is shut off. This allows the motor to restart freely. Moving
the switch to the (Off) position will remove power from the motor and stop
the air compressor.
3) AIR INTAKE FILTER: This filter is designed to clean air coming into the pump. To
ensure the pump continually receives a clean, cool, dry air supply this filter must
always be clean and ventilation opening free from obstructions. The filter can be
removed for cleaning by using warm, soapy water. Rinse the filter and air dry.
4) AIR COMPRESSOR PUMP: To compress air, the piston moves up and down in
the cylinder. On the downstroke, air is drawn in through the air intake valve while
the exhaust valve remains closed. On the upstroke, air is compressed, the intake
valve closes and compressed air is forced out through the exhaust valve, into the
discharge line, through the check valve and into the air tank.
5) SAFETY RELIEF VALVE: This valve is designed to prevent system failures by
relieving pressure from the system when the compressed air reaches a predetermined
level. The valve is preset by the manufacturer and must not be modified in any way .
To verify the valve is working properly, pull on the ring. Air pressure should escape.
When the ring is released, it will reseat.
6) AIR TANK DRAIN VALVE: The drain valve is used to remove moisture from the air
tank(s) after the air compressor is shut off. NEVER attempt to open the drain valve
when more than 10 PSI of air pressure is in the air tank! To open the drain valve,
turn the knob counterclockwise. Tilt tank to ensure that all condensation drains
through valve.
7) AIR TANK PRESSURE GAUGE: The air tank pressure gauge indicates the
reserve air pressure in the air tank (s).
8) OUTLET PRESSURE GAUGE: The outlet pressure gauge indicates the air
pressure available at the outlet side of the regulator. This pressure is controlled
by the regulator and is always less or equal to the air tank pressure.
9) PRESSURE REGULATOR: The air pressure coming from the air tank is
controlled by the regulator knob. T urn the pressure regulation knob clockwise to
increase discharge pressure, and counterclockwise to decrease discharge
pressure. Follow tool operating instructions for recommended pressure range.
10) DISCHARGE LINE: Please note that the discharge line is very hot.
1
2
3
10
6
5
7
8
9
2) MOTOR OVERLOAD: Motor has a protective breaker located on the pump.
Excessive amperage draw will result in the breaker tripping to protect the motor and
operator. Reset the breaker by pushing the black plastic stem back into the housing.
Reset switch if it is tripped.
10
PREPARATION
INITIAL SET-UP:
1. Read safety warnings before setting-up air compressor.
LOCATION:
CAUTION
In order to avoid damaging the air compressor, do not incline the air compressor
transversely or longitudinally more than 10º.
1. Place air compressor at least 12 inches away from obstacles that may prevent proper ventilation.
Do not place air compressor in an area:
-where there is evidence of oil or gas leaks.
-where flammable gas vapors or materials may be present.
WARNING
Serious injury or death may occur if electrical sparks from motor and pressure switch
come in contact with flammable vapors, combustible dust, gases or other
combustible materials. When using the air compressor for spray painting, place the
air compressor as far away from the work area as possible, using extra air hoses instead of
extension cords.
-where air temperatures fall below 32ºF or exceed 104ºF.
-where extremely dirty air or water could be drawn into the air compressor.
ELECTRICAL:
DANGER
Improper connection of the equipment-grounding conductor can result in a risk
of shock or electrocution. Check with a qualified electrician or service personnel
if you are in doubt as to whether the outlet is properly grounded. Do not use any type of
adapter with this product. If repair or replacement of the cord or plug is necessary, do not
connect the grounding wire to either flat blade terminal. The wire with insulation having
an outer surface that is green with or without yellow stripes is the grounding wire.
WARNING
This product must be grounded. If there should be a malfunction or breakdown,
grounding provides a path of least resistance for electric current to reduce the
risk of electric shock. This product is equipped with a cord having an equipment-
grounding conductor and a grounding type plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local
codes and ordinances.
1. SENCO® DOES NOT RECOMMEND THE USE OF EXTENSION CORDS as this can create power loss and
overheating of the motor. Use of an additional air hose is recommended rather than an extension cord. If use of an
extension cord is unavoidable, it should be plugged into a GFCI found in circuit boxes or protected receptacles.
When using an extension cord, observe the following:
Cable Length Wire Gauge
Up to 25 feet 12 AWG
Up to 100 feet 10 AWG
Up to 150 feet 8 AWG
Up to 250 feet 6 AWG
Use only 3-blade extension cords that have 3-blade grounding-type plugs and 3-slot cord connectors that will
accept the plug from the product. Use only extension cords having an electrical rating not less than the rating of
the product. Do not use damaged extension cords. Examine extension cord before using and replace if damaged.
Do not abuse extension cord and do not yank on any cord to disconnect. Keep cord away from heat and sharp
edges. Always shut off the air compressor switch before removing the plug from the receptacle.
11
OPERATION
PRE-START CHECKLIST:
WARNING: Risk of bodily injury. NEVER attempt to open the drain valve when
more than
10 PSI
of air pressure is in the air tank!
2. Make sure the air compressor Motor Switch is in the “OFF” position.
3. Make sure all safety valves are working correctly.
4. Make sure all guards and covers are in place and securely mounted.
START-UP:
2. Plug the power cord into the grounded outlet.
3. Move the lever on the pressure switch box to the “ON” position.
5. Set pressure by adjusting the pressure regulator knob counterclockwise for less pressure and clockwise for
more pressure.
6. If you notice any unusual noise or vibration, stop the air compressor and refer to “Troubleshooting”.
SHUTDOWN:
2. Drain air from the air tank by releasing air with an attached air tool or by pulling on the safety relief valve ring.
3. Once pressure in the air tanks register under 10 PSI, open the drain valve under each air tank to drain any
moisture.
4. Allow the air compressor to cool down.
5. Wipe air compressor clean and store in a safe, non-freezing area.
MAINTENANCE
Read the instruction manual before performing maintenance. The following procedures must be performed when
stopping the air compressor for maintenance or service.
1. Turn off the air compressor.
WARNING: Never assume the air compressor is safe to work on just because it is not
operating. It could restart at any time!
2. Disconnect cord from main power supply.
3. Open all drains.
4. Wait for the air compressor to cool before starting service.
MAINTENANCE CHART
PROCEDURE DAILY WEEKLY MONTHLY
Drain condensation in air tank(s) X
Check for unusual noise/vibration X
Check for air leaks X
Inspect air filter
X
Clean exterior of compressor
X
Check safety relief valve X
1. Remove any moisture in the air compressor tank. Remove excessive pressure by pulling on the safety relief
valve ring or with an air tool, then open the air tank drain valve in the bottom of the air tank. Close tightly
when drained.
1. Ensure the lever on the pressure switch box is in the “OFF” position.
4. This will allow the air compressor to “START” building up pressure in the air tanks and “STOP” when correct
pressure is achieved. When pressure drops with usage, the air compressor will “START” building up pressure
again.
1. To stop the air compressor, move the lever on the pressure switch box to the "OFF" position. NEVER stop
the air compressor by unplugging it from the power source. This could result in risk of electrocution.
12
TROUBLESHOOTING
Symptom 1. Motor will not run or restart.
Power cord not plugged in.
Motor/Pressure switch in “OFF” position.
Fuse blown or circuit breaker has tripped.
Wrong gauge wire or length of extension
cord.
Air tank pressure exceeds motor/
pressure switch “cut-in” pressure.
Plug cord into grounded outlet.
Move switch to “ON” position.
Replace fuse or reset circuit breaker.
Check for proper fuse amperage.
Check for low voltage conditions.
Disconnect any other electrical appliances from circuit or
operate air compressor on its own branch circuit.
Check chart on page #10 for proper gauge wire and cord length.
Motor will start automatically when air tank pressure drops
below “cut-in” pressure of motor/pressure switch.
Contact Senco Customer Service.
PROBABLE CAUSE
Motor/Pressure switch does not shut off motor when
air compressor reaches “cut-out” pressure and safety
relief valve activates.
Air compressor is incorrectly sized.
PROBABLE CAUSE
The check valve is stuck open.
REMEDY
Move the motor/pressure switch to the “Off” position.
If the motor doesn’t shutoff, unplug the air compressor.
If the electrical contacts are welded together, replace
the pressure switch.
Limit the air pressure to the capacity of the air
compressor. Either use a smaller tool or a larger air
compressor.
REMEDY
Remove, clean or replace.
Symptom 2. When in the “ON” position, motor runs continuously.
Symptom 3. Air continues to leak at motor/pressure switch release valve after motor stops.
Pressure release valve on
motor/pressure switch has not unloaded
pumphead pressure.
Bleed the line by moving the switch to the “OFF” position.
Defective motor, motor capacitor,
motor/pressure switch, or check valve.
PROBABLE CAUSE
Defective motor/pressure switch.
REMEDY
Replace
Symptom 4. Air continues to leak at motor/pressure switch release valve after motor is running.
13
PROBABLE CAUSE
Possible defective safety relief valve.
Excessive air tank pressure.
PROBABLE CAUSE
Fittings are not tight enough.
PROBABLE CAUSE
Defective or rusted air tank.
TROUBLESHOOTING
REMEDY
Operate safety relief valve manually by pulling on ring.
If it still leaks, it should be replaced.
Defective motor/pressure switch. Replace.
REMEDY
Tighten fittings where air can be heard escaping. Check
fittings with soapy water solution. Do not overtighten.
REMEDY
Air tank must be replaced. Do not attempt to repair
air tank!
Symptom 5. Air leaks from safety relief valve.
Symptom 6. Air leaks at fittings.
Symptom 7. Air leak in air tank.
PROBABLE CAUSE
Pressure regulator knob not turned to high enough
pressure or defective pressure regulator.
Restricted air intake filter.
Air leaks.
Air compressor is not large enough for air
requirement.
REMEDY
Adjust pressure regulator knob to proper setting or
replace.
Clean.
Check for leaks and repair.
Check the accessory air requirement. If it is higher than
the CFM or pressure supply of the air compressor, you
need a larger air compressor.
Symptom 9. Insufficient pressure at air tool or accessory.
PROBABLE CAUSE
Damaged inlet (reed) valve.
REMEDY
Contact SENCO Customer Service 888-222-8144.
Symptom 8. Air blowing from inlet filter.
14
PROBABLE CAUSE
Restricted air intake filter.
Defective (reed) valve.
REMEDY
Clean.
Drain air tank and measure pump up time. Compare to
specifications. If lower, remove pump head and inspect
valve plate, clean or replace.
Symptom 10. Air compressor not making enough air.
Symptom 11. Moisture in discharge air.
PROBABLE CAUSE
Condensation in air tank caused by high level
of atmospheric humidity or air compressor is
not run long enough.
REMEDY
Drain air tank after every use. Drain air tank more often
in humid weather and use an air line filter.
14
SPECIFICATIONS
Model # PC 1010
Motor
Horsepower 1 HP (peak) 1/2 HP (Running)
Voltage 115
Amperage 4
Hz. 60
Phase Single
Compressor Pump
Number of Cylinders 1
Compression Stage 1
Crankcase Aluminum
Bearings Ball
Cylinder Aluminum
Valves Reed-Single
Head Aluminum
Filter Insert
Motor/Pressure Switch Setting
Cut-out 125 PSI
Cut-in 95 PSI
Controls Start / Stop
Air tank
Capacity 1 gallon
Performance
CFM Air Displacement
CFM @ 40 PSI
CFM @ 90 PSI
CFM @ 100 PSI
Maximum Pressure 125 PSIG
Pump-up Time: 0-125 PSI 141 sec.
Recovery Time:
95-125 PSI 42 seconds
Weight
Net 20 lbs.
Dimensions
Basic LxWxH 14”x 13” x10”
RPM 3400
1.4
1.0
0.7
0.6
Limited Warranty
SENCO® Pneumatic, DuraSpin®, Cordless Tools
& Compressors
Senco Products, Inc. (“SENCO”) designs and constructs its products using the highest standards of material and workmanship. SENCO
warrants to the original retail purchaser that the following products will be free from defects in material or workmanship for the warranty
period specified below:
SENCO® XP Series-Red Cap SENCO PRO Series SENCO Compressors
Five years One year One year
SENCO® XP Series-Black Cap SENCO DuraSpin® SENCO Cordless
Two Years One year Two years
SENCO FP502 SENCO Reconditioned Products Gas Cordless
Two Years One Year Two Years
During the warranty period (which begins on the purchase date), SENCO will repair or replace, at SENCO’s option and expense, any product or part that
is defective in materials or workmanship after examination by a SENCO Authorized Warranty Service Center, subject to the exceptions, exclusions and
limitations described below. Any replacement product or part will carry a warranty for the balance of the warranty period applicable to the replaced
product or part. A DATED SALES RECEIPT OR PROOF OF PURCHASE FROM THE ORIGINAL RETAIL PURCHASER IS REQUIRED TO MAKE A
WARRANTY CLAIM. Product registration can be accomplished through on-line Product Registration at www.senco.com or by completing and returning
the postage paid product registration form included with your Operator’s manual/parts chart information, found inside the product carton. To make a
warranty claim, you must return the product, with proper receipt/proof of purchase and return transportation charges prepaid, to a SENCO Authorized
Warranty Service Center. A list of SENCO Authorized Warranty Service Centers can be found at www.senco.com or by calling 1-800-543-4596 toll free.
SENCO will perform its obligations under this warranty, within a reasonable time after approval of the warranty claim.
Wheelbarrow Compressors:
1. Subject to the exceptions, exclusions and limitations described below, SENCO warrants that the compressor pump will be free from defects in
materials and workmanship for two years after the purchase date.
2. Defective parts of the compressor pump not subject to normal wear and tear will be repaired or replaced, at SENCO's option, during the two
year warranty period. If SENCO determines that repair or replacement is not feasible, SENCO will refund the purchase price less reasonable
depreciation based on actual use.
SENCO Cordless:
1. Subject to the exceptions, exclusions and limitations described below, SENCO warrants that the SENCO Cordless tool will be free from
defects in materials and workmanship for two years after the purchase date.
2. Subject to the exceptions, exclusions and limitations described below, SENCO warrants that the batteries and chargers used with SENCO
Cordless tools will be free from defects in material and workmanship for one year after the purchase date.
WARRANTY EXCLUSIONS
The following warranty exclusions apply:
1. Normal wear parts are not covered under this warranty. Normal wear parts include, for example, isolators, drive belts, air filters, rubber o-rings,
seals, driver blades, piston stops, piston/driver assembly, and fuel stems.
2. This warranty does not cover parts damaged due to normal wear, misapplication, misuse, accidents, operation at other than recommended
speeds or voltage (electric units only), improper storage, or damage resulting during shipping.
3. Products used in production/industrial applications as defined by SENCO are excluded from this warranty.
4. Labor charges or loss or damage resulting from improper operation, maintenance or repairs are not covered by this warranty.
5. SENCO does not warrant the Wheelbarrow Compressor Engine/Motor, but the Compressor Engine/Motor may be covered under a warranty
offered by its manufacturer.
GENERAL WARRANTY CONDITIONS
This warranty will be honored, only if:
A. Clean, dry, regulated compressed air has been used, at air pressure not exceeding the maximum indicated on the tool casting;
B. No evidence of abuse, abnormal conditions, accident, neglect, misuse or improper modifications or storage of the product; and
C. No Deviation from operating instructions, specifications, and maintenance schedules exists (read Operator Manual for use, specifications, and
maintenance instructions).
THIS WARRANTY IS THE ONLY WARRANTY ON THE PRODUCT, AND SENCO DISCLAIMS ALL OTHER WARRANTIES. ANY IMPLIED
WARRANTIES WILL BE LIMITED IN DURATION TO THE APPLICABLE WARRANTY PERIOD SPECIFIED ABOVE. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. YOUR REMEDIES ARE
SOLELY AND EXCLUSIVELY AS STATED ABOVE. SENCO SHALL IN NO EVENT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT,
OR SPECIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF
CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL SENCO’S LIABILITY EXCEED THE PRICE OF THE
PRODUCT WHICH HAS GIVEN RISE TO THE CLAIM OR LIABILITY. ANY LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL
TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD SPECIFIED ABOVE. NO EMPLOYEE OR REPRESENTATIVE OF SENCO OR
ANY DISTRIBUTOR OR DEALER IS AUTHORIZED TO MAKE ANY CHANGE OR MODIFICATION TO THIS WARRANTY.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
REPLACEMENT OF TOOL DUE TO NATURAL DISASTER
SENCO will replace any tool destroyed by an Act of God such as flood, earthquake, hurricane or other disaster resulting only from the forces of nature.
Such a claim will be honored provided that such original retail purchaser had previously submitted a completed warranty registration card for the tool,
and then submits proof of ownership and an acceptable statement describing such Act of God documented by an insurance carrier, police department,
or other official governmental source. To obtain instructions for filing a claim call 1-800-543-4596.
CUSTOMER SATISFACTION
One hundred percent customer satisfaction is our #1 goal. If for any reason the product does not perform to the original purchaser’s satisfaction, it can
be returned to the place of purchase within thirty days with dated sales receipt for a full refund of the purchase price.
©2006, 2008 by SENCO PRODUCTS, INC.
CINCINNATI, OHIO 45244-1611 USA
www.senco.com
012108
Parts Reference Guide
PC1010
1/2 HP Electric Air Compressor
PC1010 Revised Date:121504 (Replaces 6/21/04) SENCO Products,Inc.Cincinnati,OH 45244-USA
Questions? Comments? call SENCO's toll-free Action-line: 1-800-543-4596 or e-mail: [email protected]
© 2004 by Senco Products, Inc.
2433005D
3B11DC02A
3201068
2405011
3B202190
2Y30QJ05
2406018
PC0057
PC0503
2408008RN
PC0057
2E2505A
2414033A
2E21045TB
2E27010F250V
3B34DC02
2Y30QJ03
SM
MEMBER
Part No. Description
3B11DC02A Exaust Valve Assembly
3201068 Cylinder
3B34DC02 Rod Assembly
2E2505A Circuit Breaker
2Y30QJ03 Air Filter Set
2E27010F250V Condensor
2406018 Pressure Relief Valve
PC0057 Pressure Gauge
2408008RN Regulator
PC0503 Quick Coupler
2Y30QJ05 Unloading Tube Set
3B202190 Unloading Tube
2E21045TB Pressure Switch
2414033A Check Valve
2405011 Drain Valve
2433005D Isolator
1
Notice technique d'utilisation
Des mises en garde pour une utilisation en toute sécurité de ce compresseur
sont incluses dans ce manual.
Compresseur d'aire électrique PC1010
PC1010 Révision du 1 Février 2008
(remplace la version 1/12/05)
Questions? Commentaires? appel gratuit de SENCO au 1-800-543-4596 ou courriel à [email protected]
Senco Products, Inc.
8485 Broadwell Rd.
Cincinnati, OH 45244
© 2004, 2008 by Senco Products, Inc.
2
TABLE DES MATIÈRES
INTRODUCTION ................................................................... 3
INSTRUCTION DE SÉCURITÉ .............................................3
INSPECTION ......................................................................... 3
MISES EN GARDE DE SÉCURITÉ ........................... 4-7
ÉLECTRICITÉ ............................................................... 4
EXPLOSION OU INCENDIE
....................................... 5
ÉCLATEMENT ............................................................... 5
INHALATION................................................................. 6
BRÛLURES .................................................................. 6
OBJETS PROJETÉS ................................................... 6
PIÈCES EN MOUVEMENT ......................................... 7
NÉGLIGENCE .............................................................. 7
AVIS SUR LA PROPOSITION CALIFORNIENNE 65... 7
CARACTÉRISTIQUES DU COMPRESSEUR
........................ 8
PRÉPARATION.................................................................... 10
MISE EN ŒUVRE INITIALE ....................................... 10
EMPLACEMENT .........................................................10
ALIMENTATION ÉLECTRIQUE ..................................10
FONCTIONNEMENT ............................................................ 11
LISTE DE VÉRIFICATIONS PRÉLIMINAIRES . ............11
DÉMARRAGE ............................................................. 11
COUPURE .............................................................. 11
ENTRETIEN .........................................................................11
DÉPANNAGE ................................................................. 12-13
SPÉCIFICATIONS ............................................................... 14
GARANTIE .......................................................................... 15
DOMMAGES AU COMPRESSEUR.............................. 7
TABLEAU DE PIÈCES ...........................................................16
3
INTRODUCTION
DANGER:
INSPECTION
Félicitations pour votre achat de notre nouveau compresseur d’air SENCO® ! Vous pouvez
être assuré que votre compresseur d’air SENCO a été construit avec le plus haut niveau de
précision et d’exactitude. Chaque composant a été rigoureusement testé par des techniciens
pour constituer la qualité, l’endurance et la performance de ce compresseur d’air.
Ce manuel d’utilisation a été composé pour vous servir. En lisant puis en appliquant les étapes
simples décrites dans de manuel de sécurisation, installation et fonctionnement, et entretien,
vous aurez des années de service sans souci pour votre nouveau compresseur à air SENCO.
Le contenu de ce manuel est basé sur les dernières informations produit disponibles au moment
de sa publication. Le constructeur se réserve le droit d’opérer des changements sur prix, couleur,
matériel et équipement, spécifications ou modèles, à tout moment et sans préavis.
ALERTES POUR LA SÉCURITÉ !
Une signalisation pour DANGER, AVERTISSEMENT ou ATTENTION pour la sécurité sera entouré d’un
encadrement d’alerte. Ce cadre est utilisé pour montrer et renforcer les mesures de sécurité qui doivent
être respectées pour faire fonctionner ce compresseur d’air. En accompagnement des mises en garde de
sécurité il y a les mots clés d’alerte qui donnent le degré de danger du risque. Les mots utilisés dans ce
manuel sont :
Indique une situation très dangereuse, qui si les mesures ne sont pas
prises ENTRAÎNERA une blessure sérieuse voire mortelle.
AVERTISSEMENT : Indique une situation potentiellement dangereuse, qui si les
mesures ne sont pas prises ENTRAÎNERAIT une blessure sérieuse voire mortelle.
ATTENTION : Indique une situation potentiellement dangereuse, qui si les mesures
ne sont pas prises POURRAIT ENTRAÎNER une blessure légère ou endommager le
compresseur d’air.
Les symboles placés à la gauche de ce paragraphe sont les symboles d’alerte de
sécurité, ils sont utilisés pour attirer l’attention sur des articles ou procédures qui
pourraient présenter un danger pour vous ou d’autres personnes utilisant cet
équipement.
FOURNISSEZ TOUJOURS UNE COPIE DE CE MANUEL À TOUTE PERSONNE QUI VA UTILISER CET ÉQUIPEMENT.
IL FAUT LIRE TOUTES LES INSTRUCTIONS DE CE MANUEL PLUS TOUTES LES INSTRUCTIONS FOURNIES PAR
LES FABRICANTS DES ÉQUIPEMENTS ANNEXES AVANT DE FAIRE FONCTIONNER LE COMPRESSEUR D’AIR, ET
PRÊTER UNE ATTENTION TOUTE PARTICULIÈRE AUX MISES EN GARDE DE SÉCURITÉ POUR ÉVITER LA
POSSIBILITÉ DE BLESSURES CORPORELLES POUR L’OPÉRATEUR.
Déballez le compresseur d’air et écrivez son numéro de série dans l’emplacement fourni plus bas. Inspectez pour
chercher des signes d’éventuels dommages évidents ou cachés venant du transport. Assurez-vous que toutes pièces
endommagées soient remplacées et que tout problème mécanique soit résolu avant de mettre le compresseur d’air en
marche.
NUMÉRO DE SÉRIE __________________________
Si vous avez des questions ou commentaires à transmettre, contactez SENCO par appel sans frais au 1-800-222-8144 ou
en envoyant un message électronique à [email protected]
Veuillez avoir sous la main ces informations en cas d’appel pour n’importe quel service :
1. Référence de modèle
2. Numéro de série
3. Date et lieu d’achat
Senco, 8485 Broadwell Road, Cincinnati, OH 45244, USA
4
CONSEQUENCES POTENTIELLES PREVENTION
DANGER
RISQUE DE
COMMOTION ÉLECTRIQUE
OU D’ÉLECTROCUTION
LISEZ TOUTES LES MISES EN GARDE DE SÉCURITÉ AVANT D’UTILISER LE
COMPRESSEUR D’AIR
MISES EN GARDE DE SÉCURITÉ
Des blessures graves ou mortelles
peuvent arriver si le compresseur
n’est pas mis à la terre de façon
convenable. Votre compresseur d’air
est alimenté de l’électricité et cela
peut provoquer une commotion
électrique ou une électrocution si
l’utilisation n’est pas correcte.
Une commotion électrique peut venir
du cordon secteur.
Une commotion électrique peut
arriver si le compresseur n’est pas
utilisé correctement.
Des blessures graves ou mortelles
peuvent arriver si des réparations
électriques sont tentées par des
personnes non qualifiées.
Assurez-vous que compresseur d’air est
bien branché sur une prise secteur
convenablement reliée à la terre, qui fournit
la tension correcte, et qui est protégée en
amont par fusible ou disjoncteur.
Vérifiez le cordon secteur pour y déceler
des signes d’écrasement, de coupure ou de
brûlure. Remplacez le cordon s’il est abîmé
avant toute nouvelle utilisation.
Gardez toutes les connexions au sec et ne
reposant pas par terre. Ne laissez pas le
cordon secteur traîner dans l’eau ou dans
une position telle que de l’eau puisse venir
à son contact. Ne touchez pas la fiche
secteur avec des mains mouillées.
Ne tirez pas sur le cordon secteur pour
débrancher la fiche de la prise murale.
Ne faites jamais fonctionner le compresseur
d’air dans des conditions d’humidité ou à
l’extérieur quand il pleut.
Ne faites jamais fonctionner le compresseur
d’air avec ses couvercles et protections de
sécurité enlevés.
Tout câblage ou dépannage électrique
effectué sur le compresseur d’air doit être
confié à un personnel de dépannage agréé,
en conformité avec les réglementations
électriques locales et nationales.
Avant d’ouvrir toute partie électrique
fermée, arrêtez toujours le compresseur
d’air, faites chuter la pression et débranchez
l’appareil de sa prise secteur. Laissez le
compresseur d’air refroidir. Ne présumez
jamais que vous pouvez intervenir en
sécurité sur le compresseur d’air juste
parce qu’il ne tourne pas. Il pourrait
redémarrer inopinément!
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
Senco PC 1010 Manuel utilisateur
- Catégorie
- Compresseurs d'air
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Senco PC 1010 User manual
- español: Senco PC 1010 Manual de usuario