Samsung DW80CG4021SR Guide d'installation

DW80CG40 Series

DD81-04332A-00

23 "(604mm)

33 "(858mm)

2 "(58.5mm)

6 "(154mm)

24"(610mm)

minimum

34 "(867mm)

minimum

24 inches deep and 34 inches high. 24"(610mm)

minimum

34

516

116

18

27

6 "

8(683mm)

25

4 "

8(625mm)

21

0 "

2(520.7mm)

(For Bar Handle models)

DW80CG40 Series

Kick Plate

For the hot water supply line – We strongly recommend using ⅜" minimum O.D. copper tubing with

a compression fitting or a flexible stainless steel braided hot water supply line.

Do not use plastic tubing. Plastic tubing can deteriorate over time and cause a leak inside the tube

fitting.

You also need a 90° Fitting with ¾" N.P.T. external pipe threads on one end and a fitting sized to fit

your hot water supply line (copper tubing/compression fitting or braided hose) on the other.

For the power cable, we recommend a jacketed 12-2 cable with ground. Note that some local codes

may require the cable to have a BX style metal jacket.

⅜"

Cable Tie

(for the Drain hose1)

Nut connector & seal

(for ¾" 90° ﬁ tting)

15

existing

The location must have sufficient space for the dishwasher door to open easily and provide

Using a 2 inch hole saw, cut a hole into the side of the cabinet that hold the sink as

12

s

Kick plate

rear

STEP 6 PREPARING THE DISHWASHER

1.

Use the provided nut connector to connect the water hose to the dishwasher.

Follow these steps:

1 2 3

A

B

C

E

F

D

1) Disconnect the 90° ﬁ tting (A) from the hose (B).

2) Remove the seal (C) and the nut (D) from the 90° ﬁ tting.

3) From the provided nut connector, separate the seal (E) and the nut (F), and then

assemble them to the 90° ﬁ tting as shown in the ﬁ gure. You must insert the smaller side

of the seal.

Then, insert the ¾" 90 degree ﬁ tting into the inlet valve (see Figure 4-B). Tighten until the ¾"

ﬁ tting is tight. Do not over tighten.

2.

3.

5.

6.

Hot Water Supply LineHot Water Supply Line

Elbow( 3/4" (9.5 mm))Elbow( 3/4" (9.5 mm))

Inlet valveInlet valve

Drain Hose2

Drain Hose1

4

raised is about 38mm(1

1 2

").

If they are rotated to the left (clockwise),they are

tightened and the front of the dishwasher is lowered.

legs.

If the leveling legs are rotated to the right (counter

clockwise),they are loosened and the front of the

dishwasher is raised. And the maximum height the

dishwasher can be

Drain hose2

12

34

Knock out plug in garbage disposal before

connecting the drain hose.

Air gap

Hose clamp

Drain

hose

With disposal Disposal with an air gap

Without an air gap

(When extending the drain hose, the maximum possible length is up to 3M.)

Drain hose2

Only qualified electricians should perform electrical

To avoid a fire hazard,make sure electrical work is

inserting

La page charge ...

Samsung DW80CG4021SR Guide d'installation

Ce manuel convient également à

Samsung DW80CG4021SR Guide d'installation

dans d''autres langues

Documents connexes