Modern Forms PD-75027 Jupiter Mode d'emploi
- Catégorie
- Mur
- Taper
- Mode d'emploi
1
INSTALLATION INSTRUCTIONS
750 - Indoor Pendant
PD-75027
HARDWARE
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019
CAUTION: To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning.
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
• Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in coastal
areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chiffon humide.
Wire
Connector
Qty: 3pcs+1Extra
Mounting
Screw
Qty:1 extra
A B C D
Plastic Anchor
Qty: 2pcs+1 extra Qty: 2pcs+1 extra
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture,
including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear area.
Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) and back plate from the fixture.
4. Drill holes in the wall aligned with the key hole located in the mounting
back plate, insert the plastic anchors(C).
5. Secure the mounting back plate to the junction box using standard
junction box screws that comes with the junction box. Fasten it to the
wall using wood screw (D).
Note: the side of the mounting plate marked “GND” must face out.
6. Properly secure the safety cord to the bracket on mounting back plate to
temporary hang the fixture in place.
7. Adjust the fixture wire length by pushing the cable gripper onthe canopy
and pulling the wire as desired.
a. Retract the wires close to the desired length within thecanopy
before securing the fixture in place.
NOTE: Using the cable gripper to adjust more than 18” of wire length is
not recommended.
WARNING: Shortening the cables without professional help or electronic
background is not advisable. Any modifications to the fixture will result
in voiding the warranty of the product.
CONNECTING THE WIRES (Fig. 2)
8. Connect the driver’s input wires to junction box wires as shown in Fig. 2,
making sure that all wire connectors (A) are secured. If your outlet box has
a green or bare copper ground wire, connect the xture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly to the back plate
using the green screw provided. After wires are connected, tuck them
carefully inside the junction box.
COMPLETING THE INSTALLATION
9. Hold the canopy in both hands and put it on the mounting ring as shown
in the Fig. 1, then rotate in the direction of the arrow until it can't move.
Secure it with mounting screw (B).
NOTE: DIMMING WIRING INFORMATION (Fig. 3)
10. This fixture features electronic low voltage (ELV) or 0-10V dimming capabilities. See notes below for speci c dimming wires information..
11. To utilize ELV dimming: use wires black (hot), white (neutral) and green ground wire (ground). .
12. To utilize 0-10V dimming: use wire purple (dim+), Pink or gray (dim-), black (hot), white (neutral) and green ground wire (ground).
2
INSTALLATION INSTRUCTIONS
750 - Indoor Pendant
PD-75027
FIG.1
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Ø61
4"
Ø31
2"
Ø23
4"
Ø81
8"
Purple - Dim+
Black - Output -
Red - Output +
White - Neutral
Black - Hot
Purple - Dim+
Pink or gray-Dim-
Black - Output -
Red - Output +
Outer Ring
Inner Ring
Outer bare cord
Inner cord
Inner cord
Outer bare cord
LD-1200MA50U-DI-IS
LD-350MA14U-DIM-IS
Push up
Cable-gripper
Mounting screw
B
Junction box
Driver(2pcs)
Junction box screw
Plastic anchor
Safety cord
A
Wire connector
Mounting backplate
Ground wire
Wood screw
C
D
Driver input wire
Cord
Fixture
FIG. 2 Wiring
Mounting Backplate DimensionFIG. 3 Driver Wiring
Pink or gray-Dim-
-
1
-
2
Modern Forms PD-75027 Jupiter Mode d'emploi
- Catégorie
- Mur
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms PD-81004 Minx Mode d'emploi
-
-
-
-
-
-
-
-
-