Modern Forms PD-94322 Echelon Mode d'emploi

Taper
Mode d'emploi
1
INSTALLATION INSTRUCTIONS

PD-94322
HARDWARE
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Sep. 2022

Read all instructions before installing.
System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
Retain installation instructions for future maintenance reference.
All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.

Lisez toutes les instructions avant l’installation.
Le système doit être installé par un électricien licensié conformément au code national de lélectricité (NEC), et également aux
règlements locaux.
Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
 Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
 Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.












2
INSTALLATION INSTRUCTIONS

PD-94322
FIG. 1
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Sep. 2022
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
FIG. 2 Wiring
Fig.3 Driver Wires
White - Neutral
Black - Hot
Red +
Black -
Red +
Black -
Driver
Input
Output
Canopy
Mounting Backplate Dimensions
Ø45
8"
13
8
"
13
4"

1. Shut o the power at the circuit breaker and remove existing xture,
including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear
area. Be careful not to lose any small parts necessary for installation.

3. Ax the four ns into the upper socket and fasten using the long
allen screw(F) with the allen wrench(D).
4. Ax the ns to the bottom socket and secure with the bottom cap.
While securing the bottom cap, hold on to the bottom socket to
prevent rotation. Fasten with short Allen screw (E) and Allen wrench (D).
5. Fasten the short allen screw (E) with the allen wrench(D) .
6. Remove the mounting screw (C) from the xture.
7. Choose number of rods suitable for your application. Thread the
xture wire through the rods, swivel and canopy, connect canopy,
swivel, rods and xture body. Ensure all are tightened.

8. Cut the extra wire thread from the xture. Connect the driver input
wire with junction box as shown in Fig.2, make sure that all wire
connectors (A) are secured. If your outlet box has a green or bare
copper ground wire, connect the xtures ground wire to it. Other
wise, connect the xture’s ground wire directly to the back plate
using the GND screw provided. After wires are connected, tuck them
carefully inside the junction box.
Due to limited room within the canopy, shorten the cable as
necessary to make the installation easier. Make sure to identify and
label all the wiring properly before any trimming/shortening.

9. Secure mounting plate to the junction box using junction box screw.
(i) using any other non-original-manufacturer provided
junction box screw may result in safety issue;
(ii) The side of the mounting plate marked “GND” must face out.
10. Connect the driver output wire with xture wire as shown in Fig. 3 .Red to
the red, and black to the black, makingsure that all wire connectors (C) are
secured.Connect the driver input wires to junction box as shown in Fig .2.
Making sure that all wire connectors (A) are secured. If your outlet box has
a green or barecopper ground wire, connect the xture’s ground wire to it.
Otherwise, connect the xture’s ground wire directly to the back plate
using the GND screw provided. After wires are connected, tuck them
carefully inside the junction box.
11. Secure the xture by mounting the canopy to the ring of the back plate.
Turn and rotate the canopy in the direction of the arrow until it stops.
Fasten the canopy to the mounting back plate using the mounting
screw(B)
12. For slope ceiling application, rotate swivel at the top of the stem to
ensure luminaireis aiming down (Fig. 4).
Turn to down












Wire Connectors














  • Page 1 1
  • Page 2 2

Modern Forms PD-94322 Echelon Mode d'emploi

Taper
Mode d'emploi