veratron B00043501 Manuel utilisateur

B000882

VL FLEX 52MM SERIES

VL FLEX 52

NMEA 2000

USER MANUAL

rev. AB

EN

DE

IT

FR

ES

PT

B000882

LANGUAGE PAGE

ENGLISH 3

DEUTSCH 26

ITALIANO 50

FRANÇAIS 74

ESPAÑOL 98

B000882

VL FLEX 52MM SERIES

VL FLEX 52

NMEA 2000

USER MANUAL

rev. AB

EN

DE

IT

FR

ES

PT

CONTENT

B000882

CONTENT

Content ............................................................................................ 2

Introduction .................................................................................... 3

Package Contents ..................................................................................... 3

The all-in-one Device ............................................................................... 3

Contactless Configuration .................................................................... 3

Safety Information ......................................................................... 4

Safety During Installation ....................................................................... 4

Safety After Installation ........................................................................... 5

Electrical Connection .............................................................................. 5

Installation ...................................................................................... 6

Before the Assembly ................................................................................ 6

Mounting with Spinlock Nut .................................................................. 7

Flush Mounting ........................................................................................... 8

Connections .................................................................................... 9

Pinout .............................................................................................................. 9

Wiring Harness ............................................................................................ 9

NMEA 2000® Pinout ........................................................................... 10

Connection to the NMEA 2000® Network ............................... 10

Frequency Input Connection............................................................... 11

Resistance Sensor Connection ........................................................... 11

Configuration ............................................................................... 12

VL Fex Configurator App ...................................................................... 12

Configure Device ...................................................................................... 12

Supported Configurations ................................................................... 16

Display Layout .............................................................................. 18

Single Layout .............................................................................................. 18

Dual Layout ................................................................................................. 18

ALARM DISPLAY ..................................................................................... 19

Technical Data ............................................................................. 20

Datasheet.................................................................................................... 20

Supported NMEA 2000® PGNs ...................................................... 21

Accessories .................................................................................. 22

INTRODUCTION

B000882

INTRODUCTION

PACKAGE CONTENTS

Item number

Description

B00043501

1x VL Flex 52

A2C5205947101

1x 52 mm spinlock nut

A2C9582260001

1x wiring harness

B000100

1x safety instructions

THE ALL-IN-ONE DEVICE

The VL Flex 52 can be easily configured as the display device you need thanks to its 1.44" TFT display,

readable even in strong sunlight, embedded in a standard 52 mm diameter housing.

Supported analog inputs allow direct reading from motor sensors, and the NMEA 2000® interface extends

this function by allowing the VL Flex to read from the digital network.

The simple but effective display layout can be set up in a single or dual layout, presenting the data in a clear

and intuitive way, while the colored bar graph and alarm display allow you to interpret the data more quickly.

CONTACTLESS CONFIGURATION

Thanks to contactless configuration, you can configure your all-in-one instrument with a simple "tap"!

Start the smartphone app and define your settings via the user-friendly interface. Then simply hold your

smartphone on the front lens of the VL Flex to transfer the configuration immediately.

Thanks to the built-in passive antenna, the configuration can be done without power supply!

SAFETY INFORMATION

B000882

SAFETY INFORMATION

WARNING

• No smoking! No open fire or heat sources!

• The product was developed, manufactured

and inspected according to the basic safety

requirements of EC Guidelines and state-of-

the-art technology.

• The instrument is designed for use in grounded

vehicles and machines as well as in pleasure

boats, including non-classified commercial

shipping.

• Use our product only as intended. Use of the

product for reasons other than its intended use

may lead to personal injury, property damage

or environmental damage. Before installation,

check the vehicle documentation for vehicle

type and any possible special features!

• Use the assembly plan to learn the location of

the fuel/hydraulic/compressed air and

electrical lines!

• Note possible modifications to the vehicle,

which must be considered during installation!

• To prevent personal injury, property damage or

environmental damage, basic knowledge of

motor vehicle/shipbuilding electronics and

mechanics is required.

• Make sure that the engine cannot start

unintentionally during installation!

• Modifications or manipulations to veratron

products can affect safety. Consequently, you

may not modify or manipulate the product!

• When removing/installing seats, covers, etc.,

ensure that lines are not damaged and plug-in

connections are not loosened!

• Note all data from other installed instruments

with volatile electronic memories.

SAFETY DURING INSTALLATION

• During installation, ensure that the product’s

components do not affect or limit vehicle

functions. Avoid damaging these components!

• Only install undamaged parts in a vehicle!

• During installation, ensure that the product

does not impair the field of vision and that it

cannot impact the driver’s or passenger’s head!

• A specialized technician should install the

product. If you install the product yourself,

wear appropriate work clothing. Do not wear

loose clothing, as it may get caught in moving

parts. Protect long hair with a hair net.

• When working on the on-board electronics, do

not wear metallic or conductive jewelry such as

necklaces, bracelets, rings, etc.

• If work on a running engine is required, exercise

extreme caution. Wear only appropriate work

clothing as you are at risk of personal injury,

resulting from being crushed or burned.

• Before beginning, disconnect the negative

terminal on the battery, otherwise you risk a

short circuit. If the vehicle is supplied by

auxiliary batteries, you must also disconnect

the negative terminals on these batteries!

Short circuits can cause fires, battery

explosions and damages to other electronic

systems. Please note that when you disconnect

the battery, all volatile electronic memories

lose their input values and must be

reprogrammed.

• If working on gasoline boat motors, let the

motor compartment fan run before beginning

work.

• Pay attention to how lines and cable harnesses

are laid so that you do not drill or saw through

them!

• Do not install the product in the mechanical

and electrical airbag area!

SAFETY INFORMATION

B000882

• Do not drill holes or ports in load-bearing or

stabilizing stays or tie bars!

• When working underneath the vehicle, secure

it according to the specifications from the

vehicle manufacturer.

• Note the necessary clearance behind the drill

hole or port at the installation location.

Required mounting depth: 65 mm.

• Drill small ports; enlarge and complete them, if

necessary, using taper milling tools, saber saws,

keyhole saws or files. Deburr edges. Follow the

safety instructions of the tool manufacturer.

• Use only insulated tools, if work is necessary on

live parts.

• Use only the multimeter or diode test lamps

provided, to measure voltages and currents in

the vehicle/machine or boat. Use of

conventional test lamps can cause damage to

control units or other electronic systems.

• The electrical indicator outputs and cables

connected to them must be protected from

direct contact and damage. The cables in use

must have enough insulation and electric

strength and the contact points must be safe

from touch.

• Use appropriate measures to also protect the

electrically conductive parts on the connected

consumer from direct contact. Laying metallic,

uninsulated cables and contacts is prohibited.

SAFETY AFTER INSTALLATION

• Connect the ground cable tightly to the

negative terminal of the battery.

• Reenter/reprogram the volatile electronic

memory values.

• Check all functions.

• Use only clean water to clean the components.

Note the Ingress Protection (IP) ratings (IEC

60529).

ELECTRICAL CONNECTION

• Note cable cross-sectional area!

• Reducing the cable cross-sectional area leads

to higher current density, which can cause the

cable cross-sectional area in question to heat

up!

• When installing electrical cables, use the

provided cable ducts and harnesses; however,

do not run cables parallel to ignition cables or

to cables that lead to large electricity

consumers.

• Fasten cables with cable ties or adhesive tape.

Do not run cables over moving parts. Do not

attach cables to the steering column!

• Ensure that cables are not subject to tensile,

compressive or shearing forces.

• If cables are run through drill holes, protect

them using rubber sleeves or the like.

• Use only one cable stripper to strip the cable.

Adjust the stripper so that stranded wires are

not damaged or separated.

• Use only a soft soldering process or

commercially available crimp connector to

solder new cable connections!

• Make crimp connections with cable crimping

pliers only. Follow the safety instructions of the

tool manufacturer.

• Insulate exposed stranded wires to prevent

short circuits.

• Caution: Risk of short circuit if junctions are

faulty or cables are damaged.

• Short circuits in the vehicle network can cause

fires, battery explosions and damages to other

electronic systems. Consequently, all power

supply cable connections must be provided

with weldable connectors and be sufficiently

insulated.

• Ensure ground connections are sound.

• Faulty connections can cause short circuits.

Only connect cables according to the electrical

wiring diagram.

•

If operating the instrument on power supply

units, note that the power supply unit must be

stabilized and it must comply with the following

standard: DIN EN 61000, Parts 6-1 to 6-4.

INSTALLATION

B000882

INSTALLATION

WARNING

Before beginning, disconnect the negative terminal on the battery, otherwise you risk a

short circuit.

If the vehicle is supplied by auxiliary batteries, you must also disconnect the negative terminals on these

batteries! Short circuits can cause fires, battery explosions and damages to other electronic systems.

Please note that when you disconnect the battery, all volatile electronic memories lose their input values

and must be reprogrammed.

BEFORE THE ASSEMBLY

1.

Before beginning, turn off the ignition and

remove the ignition key. If necessary, remove

the main circuit switch

2. Disconnect the negative terminal on the

battery. Make sure the battery cannot

unintentionally restart.

3. Place the device at least 300 mm away from

any magnetic compass.

INSTALLATION

B000882

MOUNTING WITH SPINLOCK NUT

Conventional mounting. (Device is inserted into the hole from the front).

The panel thickness can be in the range of 0.5 to 20 mm. The hole must have a diameter of 53 mm [B].

WARNING

• Do not drill holes and installation openings in load-bearing or stabilizing struts or spars!

• For the installation location, ensure the necessary clearance behind the holes or the installation

opening. Required installation depth 65 mm.

• Pre-drill small installation openings, enlarge with cone cutter, hole saw, jigsaw or file if necessary and

finish. Deburr edges. Refer to the safety instructions of the hand tool manufacturer.

1. Different covers can be mounted as an

alternative to the supplied cover. In this case,

carefully remove it with a screwdriver [A],

attach the new bezel to the instrument and

press it until it is flush with the cover glass.

Note: When removing, the front ring

damaged and can no longer be used

be

IMPORTANT: If you install a chrome bezel, you

must set up the device before installation. The

metal particles contained in the chrome trim

may affect the performance of the wireless

interface!

2. Make a round hole, taking into account the

external dimensions of the device. [B]

3. Remove the spinlock nut and insert the device

frontally. [C]

4. Align the spinlock nut as shown in [D],

according to the thickness of the plate.

5. Feed the cables through the spinlock nut and

carefully screw it in at least two turns.

6. Connect the plugs.

A B

C

D

INSTALLATION

B000882

FLUSH MOUNTING

The recommended panel thickness is 1.5 to 3mm. The hole must have a diameter of 48.1mm [A].

Make sure that the installation location is level and has no sharp edges.

WARNING

• Do not drill holes and installation openings in load-bearing or stabilizing struts or spars!

• For the installation location, ensure the necessary clearance behind the holes or the installation

opening. Required installation depth 65 mm.

• Pre-drill small installation openings, enlarge with cone cutter, hole saw, jigsaw or file if necessary and

finish. Deburr edges. Refer to the safety instructions of the hand tool manufacturer.

1. Make a round hole, taking into account the

external dimensions of the device. [A]

2. Remove the spinlock nut

3. Remove the front ring using a screwdriver. [B]

Note: When removing, the orifice plate will be

damaged and can no longer be used.

4. Place the flushmount gasket A2C53215640 (not

included) on the cover glass.

5. Insert the device into the hole [C] from behind.

6. Align the unit so that the reading is straight and

fix it to the studs [D] attached to the back of the

panel using the flushmount mounting bracket

A2C59510864 (not included).

7. Connect the plugs.

A

B

C

D

CONNECTIONS

B000882

CONNECTIONS

PINOUT

Pin no. Cable color

Description

1 Red Term. 15 - Battery 12 / 24 V

2 Black Term. 31 - Ground

3

Green

/

Red Signal - frequency sensor

4

Yellow

/

Red Signal - resistance sensor

5

Blue /

White LIN bus

6 Red / White

Illumination day/night

7 -

NMEA 2000

High

(

on M12

connector)

8 -

NMEA

2000

Low

(

on M12

connector)

Rear view VL Flex

Tyco / Hirschmann 8-poles MQS plug

WIRING HARNESS

Wiring harness

VL Flex

A: NMEA 2000® DeviceNet M12 5-pin connector

B: Cables for sensor connection and power supply (see colors in the table)

C: VL Flex connector - Tyco / Hirschmann MQS 8-pin

CONNECTIONS

B000882

NMEA 2000® PINOUT

Micro-C M12 5-pin connector

Male, Cable View

Pin no.

Description

1

Shielding

2

NET

-

S (V+)

3

NET

-

C (V

-

)

4

NET

-

H

(CAN H)

5

NET

-

L (CAN L)

CONNECTION TO THE NMEA 2000® NETWORK

Once mounting is complete, the device can be connected to

the NMEA 2000® network via the designated socket on the

cabling.

Make sure to screw the plug all the way on. This is the only way

to guarantee that the connection is waterproof.

A drop cable is only required if the total length of the supplied

cabling is not sufficient to reach the NMEA 2000® backbone.

In this case it is possible to extend the cable with one of the

additional drop cables.

Note that NMEA 2000® does not allow drop cables longer

than 6 meters.

Stick to the NMEA 2000® standard for proper network setup.

CONNECTIONS

B000882

FREQUENCY INPUT CONNECTION

Designations within the connection

diagram:

15 - Term. 15 - switched positive 12/24

V (ignition)

31 - Term. 31 - Mass

F1 - Fuse 3A (not included)

S1 - Illumination switch day/night (not

included)

RESISTANCE SENSOR CONNECTION

Designations within the connection

diagram:

15 - Term. 15 - switched positive 12/24

V

(Ignition)

31 - Term. 31 - Mass

F1 - Fuse 3A (not included)

S1 - Illumination switch day/night (not

included)

CONFIGURATION

B000882

CONFIGURATION

VL FEX CONFIGURATOR APP

To configure the VL Flex, some parameters have to be configured, e.g. the display type, the connected

sensor and its calibration or the alarm threshold.

This is possible via the smartphone app "VL Flex Configurator", which can be downloaded free of charge

from the stores for both Android and iOS devices.

You can also find a simple explanation of the setup process as in-app instructions.

Thanks to the passive NFC receiver, the VL Flex device can be configured as described below without the

need for a power supply.

VL FLEX

CONFIGURATOR

CONFIGURE DEVICE

Setting up the VL Flex device is a three-step process.

Remember that the configuration of the instrument must be read before it can be changed and written to

the instrument.

1.

READ

2.

CONFIGURE

3.

WRITE

CONFIGURATION

B000882

1.

READ CONFIGURATION

Open the "VL Flex Configurator" app and read the

current configuration of the device by "touching" the

front lens of the device with the smartphone.

The READ operation is mandatory before the WRITE

operation is allowed.

After reading, the app is set with the current

configuration of the VL Flex.

Note: The position of the antenna on the smartphone

depends on the model.

For more information, refer to the smartphone

manufacturer's manual.

2.

SELECT DISPLAY LAYOUT

Use the Layout section to choose between single and

double image layouts.

The preview image at the top of the app screen will

update accordingly.

When Dual Layout is selected, the app expands the

device settings to be able to configure both fields of

the screen.

3.

SELECT DISPLAY TYPE

Use the Gauge Type item in the Data Selection

section to select the data to be displayed on the VL

Flex.

If the dual layout is selected, you can select the data

for the upper as well as for the lower part of the screen

separately.

Note: For the complete list of supported data types,

see the Supported Configurations table in this

document.

4.

SELECT MASS UNITS AND INSTANCE

CONFIGURATION

B000882

Define the

unit of measurement for the

displayed

data. (see table "Supported configurations").

Set the instance for the displayed data (e.g. engine

number or tank number) so that they are shown

correctly on the display.

Some rudder position sensors send their data on their

own instance instead of the associated instance of the

engine. In this case, the "Ignore" option must be

selected as the Engine Instance.

Note: The defined instance is also used by the VL Flex

when receiving data from NMEA 2000®.

5.

ALARM SETTINGS

For some data types an alarm can be set (see table

"Supported configurations").

The alarm can be activated or deactivated via the

corresponding switch in the app.

Once the option is enabled, the threshold value can

be set using the corresponding numeric field.

The unit of the alarm threshold is the same unit that

was defined in the previous step.

Note: The "direction" of the alarm threshold (up or

down) is predefined (see table "Supported

configurations").

6.

CALIBRATE SENSOR

By default, the VL Flex assumes that data is received

via NMEA 2000® , so the analog inputs are disabled.

If a sensor is connected via an analog connection

(resistance or frequency), it can be configured by

activating the corresponding switch in the app.

Note: Depending on the type of display configured,

only one of the available inputs can be assigned to the

data type. (see table "Supported configurations")

If a dual layout (two values) has been selected, you

can select which data is to be configured as an analog

input.

The other data is considered to be received from the

NMEA 2000® network.

CONFIGURATION

B000882

7.

LIGHTING AND CLOCK

You can complete the configuration of the VL Flex via

the "Settings" tab.

In this section you can set the intensity of the

backlight during the day and night using the slider.

This screen can also be used to adjust the clock

settings (format and offset).

Note: The clock is only received via NMEA 2000®

from an external GPS receiver. It is not counted

internally by the VL Flex.

8. TRANSFER CONFIGURATION

Once the configuration is complete, you can

download it to VL Flex.

Press the "APPLY" button in the upper right corner of

the app and "touch" the front lens of the device with

your smartphone.

CONFIGURATION

B000882

SUPPORTED CONFIGURATIONS

Display type Unit Resistance

Sensor

Frequency

Sensor Calibrations Alarm

available

PGN

Tachometer rpm - ✔ Pulses per

revolution No 127488

Boat speed

kn

km/h

mph

- ✔ Pulses per unit No 128259

Ammeter

A - - - No 127508

Voltmeter

V - - Measures supply

voltage No 127508

Battery charge % - - - Yes

(below) 127506

Battery status

% - - - Yes

(below) 127506

Battery temperature

°C

°F - - - Yes

(above) 127508

Battery autonomy

h

days - - - No 127506

Operating hours

h - ✔ Calculated

internally No 127489

Speed Over Ground

kn

km/h

mph

- - - No 129026

Course Over Ground

deg - - - No 129026

Depth

m

ft - - - Yes

(below) 128267

Fuel level

% ✔ -

0

-

90

Ω

3 - 180 Ω

240 - 33 Ω

90 - 4 Ω

105 - 4 Ω

Yes

(below) 127505

Fresh water level

% ✔ -

3 - 180 Ω

240 - 33 Ω

90 - 4 Ω

No 127505

Waste water level

% ✔ -

3 - 180 Ω

240 - 33 Ω

90 - 4 Ω

No 127505

CONFIGURATION

B000882

Display type Unit Resistance

Sensor

Frequency

Sensor Calibrations Alarm

available

PGN

Trim % ✔ -

167

-

10

Ω

(

Single

Station)

84 - 5 Ω (Dual

Station)

No 127488

Rudder position deg ✔ -

10

-

180

Ω

(

Single

Station)

5 - 90 Ω (Dual

Station)

No 127245

Cooling water temp. °C

°F ✔ -

291 - 22 Ω (120 °C)

322 - 19 Ω

(150 °C)

Yes

(above) 127489

Boost pressure bar

PSI ✔ - 10 - 184 Ω (2 bar)

10 - 184 Ω (5 bar) No 127488

Engine oil pressure bar

PSI ✔ - 10 - 184 Ω (5 bar)

10 - 184 Ω (10 bar)

Yes

(below) 127489

Engine oil temp. °C

°F ✔ - 322 - 19 Ω

(150 °C)

Yes

(above) 127489

Transmission oil

pressure

bar

PSI ✔ -

10 - 184 Ω (10 bar)

10 - 184 Ω (25 bar)

10 - 211 Ω (30 bar)

Yes

(below) 127493

Transmission oil

temp.

°C

°F ✔ - 322 - 19 Ω

(150 °C)

Yes

(above) 127493

Clock

- - - - No 126992

* Supported configurations can be updated at any time. Make sure you always use the latest version of the

app.

DISPLAY LAYOUT

B000882

DISPLAY LAYOUT

SINGLE LAYOUT

A.

Symbol

Indicates, which data type is displayed right now.

For the data types, which support this function, there is

also the instance indicated here.

B.

Unit

Shows the unit of the currently displayed data.

For some data types it’s possible to change the unit in

the settings. (See table “Supported Configurations”)

C.

Measured

value

This shows the numeric value of the dedicated

measured data. If there aren’t any values received for

this data type or they are out of range, the display will

show “---“.

Coloured Graph

The coloured graphic in the background is a bar

diagram that puts the measured value in perspective.

This function isn’t supported for all data types.

The white lines on the left side show the scalation.

DUAL LAYOUT

A.

Symbol

Indicates, which data type is displayed right now.

For the data types, which support this function, there is

also the instance indicated here.

B.

Unit

Shows the unit of the currently displayed data.

For some data types it’s possible to change the unit in

the settings. (See table “Supported Configurations”)

C.

Measured Value

This shows the numeric value of the dedicated

measured data. If there aren’t any data received for this

data type or the values are out of range, the display will

show “---“.

The bar graph can’t be displayed in the dual layout for

any value.

A

B

C

B

C

A

La page charge ...

veratron B00043501 Manuel utilisateur

veratron B00043501 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents