Technical Characteristics
Materials: -Body: low-lead brass (<0.25% lead content)
-Shutter, seats and sliding guides: PPO
-Springs: stainless steel
-Seals: peroxide-cured EPDM
Suitable fluids: water, 30% max glycol solution
Setting range (outlet temperature): 85–150°F (30–65°C)
Tolerance: ±3°F (±2°C)
Max. working pressure (static): 200 psi (14 bar)
Max. operating differential pressure (dynamic): 75 psi (5 bar)
Max. recommended differential pressure: 20 psi (1.5 bar)
Max. hot water inlet temperature: 200°F (93°C)
Max. inlet pressure ratio (H/C or C/H) for optimum performance: 2:1
Min. temperature difference between hot water inlet and mixed
water outlet for optimum performance: 27ºF (15ºC)
Min. flow rate to ensure optimal performance: 1.0 GPM (3.8 L/min)
Lay length, hot to cold inlet: (½” & ¾” press connection) 3 5/8”
(1” press connection) 4 1/8”
(1 “ with inlet check valves) 7 ¼”
Certified to: 1. ASSE 1017/CSA B125.3, certified by ICC-ES, file
PMG-1357
2. NSF/ANSI/CAN 372-2011, Drinking Water System
Components-Lead Content Reduction of Lead in
Drinking Water Act, California Health and Safety
Code 116875 S.3874, Reduction of Lead in
Drinking Water Act, certified by ICC-ES, file
3. PEX crimp fittings certified to ASTM F 1807.
4. PEX expansion fittings certified to ASTM F 1960.
PMG-1360.
Function
The Caleffi MixCal™ three-way thermostatic mixing valve is used in
systems producing domestic hot water or in hydronic and radiant
heating systems. With the unique mixing chamber design, MixCal™
produces very stable mixed water temperture as inlet temperatures
and pressures vary. Scale formation is minimized with anti-scale
polymer sliding surfaces, preventing siezing or erratic mixed
temperatures. O-ring seals made from durable peroxide-cured EPDM
resist wear from common water treatment additives such as chlorine
and chloramines.
Product range
521A Series Three-way thermostatic mixing valve:
“C” models include inlet check valves. “41x, 51x, 61x” models include
outlet gauge adapter. Connections: union thread NPT male, sizes ½”,
¾”, 1”; union sweat, sizes ½”, ¾”, 1”; union press, sizes ½” , ¾”, 1”;
union PEX crimp, sizes ½” , ¾”, 1”; and union PEX expansion, sizes
½” , ¾”, 1”.
MixCal™ Adjustable three-way thermostatic mixing valve
521 series
© Copyright 2023 Caleffi
38476.14
www.caleffi.com
1
LEAVE THIS MANUAL FOR THE USER.
CAUTION: If the thermostatic mixing valve is not installed, commissioned
and maintained properly, according to the instructions contained in this
manual, it may not operate correctly and may endanger the user.
CAUTION: Make sure that all the connecting pipework is water tight.
CAUTION: When making the water connections, make sure that the pipwork
connecting the MixCal™ thermostatic mixing valve is not mechanically
overstressed. Over time this could cause breakages, with consequent water
losses which, in turn, could cause harm to property and/or people.
CAUTION: Water temperatures higher than 100ºF (38ºC) can be dangerous.
During the installation, commissioning and maintenance of the MixCal™
thermostatic mixing valve, take the necessary precautions to ensure that such
temperatures do not endanger people.
CAUTION: To prevent any damage which will cause the electronic mixing
valve to not operate correctly, treat highly aggressive water before entering
the thermostatic mixing valve. Be sure water hardness is less than 10 grains.
CAUTION: If installed in an ASSE 1017 application, check valves shall be
used.
SAFETY INSTRUCTION
CAUTION: All work must be preformed by qualified personnel trained in the
proper application, installation, and maintenance of systems in accordance
with all applicable codes and ordinances.
This safety alert symbol will be used in this manual to draw attention to safety related
instructions. When used, the safety symbol means ATTENTION! BECOME ALERT!
YOUR SAFETY IS INVOLVED! FAILURE TO FOLLOW THESE INSTRUCTIONS MAY
RESULT IN A SAFETY HAZARD.
2
WARNING: This product can expose you to chemicals including lead, which
is known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information go to www.P65Warnings.ca.gov.
ATTENTION: Lorsque vous effectuez les raccordements d'eau, assurez-
vous que la tuyauterie reliant le MixCal™ termostatico regolabile n'est pas
mécaniquement des overstressed. Au fil du temps, ceci pourrait causer des
ruptures, avec pour consequence des pertes en eau qui, à leur tour, peuvent
causer des dommages à la propriété et/ou les gens.
Ce symbole d'avertissement servira dans ce manuel à attirer l'attention sur la sécurité concernant
instructions. Lorsqu'il est utilisé, ce symbole signifie.
ATTENTION! DEVENEZ ALERTE ! VOTRE SÉCURITÉ EST EN JEU ! NE PAS SUIVRE CES
INSTRUCTIONS PEUT PROVOQUER UN RISQUE DE SECURITE.
ATTENTION: Tous les travaux doivent être effectués par du personnel qualifié
formé à la bonne application, installation et maintenance des systèmes
conformément aux codes et règlements locaux.
ATTENTION: Si le réducteur de pression, termostatico regolabile, n'est pas installé,
mis en service et entretenu correctement, selon les instructions contenues dans ce
manuel, il peut ne pas fonctionner correctement et peut mettre en danger l'utilisateur.
ATTENTION: S'assurer que tous les raccordements sont étanches.
ATTENTION: Les températures de l'eau supérieure à 100°F (38°C) peut
être dangereux. Au cours de l'installation, mise en service et l'entretien de
le réducteur de pression, le MixCal™ termostatico regolabile, prendre les
precautions nécessaires afin de s'assurer que de tells températures ne
compromettent pas les gens.
ATTENTION: Pour prévenir tout dommage qui provoque le mitigeur
électronique à ne pas fonctionner correctement, le traitement de l’eau très
agressive avant d’entrer dans le termostatico regolabile. Assurez-vous que la
dureté de l’eau est inférieure à 10 grains.
ATTENTION: S’il est installé dans un pays de ASSE 1017 application, vérifiez les
robinets doivent être utilisés.
CONSIGNE DE SÉCURITÉ
LAISSEZ CE MANUEL AVEC L’UTILISATEUR
3
AVERTISSEMENT:
Ce produit peut vous exposer à des produits chimiques comme le
plomb, qui est connu dans l’État de Californie pour causer le cancer, dommages à la
naissance ou autre. Pour plus d’informations rendez-vous www.P65Warnings.ca.gov.
COLD
HOT
MIX
COLD
HOT
MIX
30
50
70
90
110130
150
170
190
210
ºF
Operating principle
The controlling element of the three-way
thermostatic mixing valve is a thermostatic
sensor fully immersed in the mixed water
outlet tube which, as it expands or contracts,
continuously establishes the correct proportion
of hot and cold water entering the valve. The
regulation of these flows is by means of a
piston sliding in a cylinder between the hot
and cold water passages. Even when there
are pressure drops due to the drawing off of
hot or cold water for other uses, or variations
in the incoming temperature, the thermostatic
mixing valve automatically regulates the water
flow to obtain the required temperature.
COLD
HOT
MIX
Inlet port check valve detail for 521 “AC” models
Flow curve
Flow should never exceed standards for pipe size and materials.
Kv = 2.6
0.1
10
0.023
0.23
0.046
0.069
0.02
0.05
0.2
0.5
0.115
2.3
0.46
0.69
1.15
20
50
∆p (ft of head)
G (l/min) (
gpm
)
23
4.6
6.9
11.5
46
0.01
0.1
0.02
0.03
0.05
1
0.2
0.3
0.5
(psi) (bar)
10
2
3
5
20
1
0
.1
0.2
0.5
0.05
10
2
5
20
0.001
0.01
0.002
0.003
0.005
0.1
0.02
0.03
0.05
1.0
0.2
0.3
0.5
Cv = 3.0
9.2
0.092
0.92
0.04
0.4
4
0.004
0.04
0.4
50
115
161
50
70
2.0
5.0
190
70
100
140
4
LARGE MIXING
CHAMBER
CHECK VALVE
Posi-Stop™
UNION SEALS
(on 3 ports)
EASY-GRIP
KNOB
TAMPER-PROOF
SETTING LOCK
Use
Caleffi MixCal series 521 thermostatic mixing valves are designed to be installed at the hot water
heater. The Caleffi MixCal series 521 valve cannot be used for tempering water temperature at
fixtures as a point-of-use valve. They are not designed to provide scald protection or anti-chill service.
They should not be used where ASSE 1070 devices are required. Wherever a scald protection feature
is required, Caleffi series TubMixer™ 5213 high performance mixing valve needs to be installed. For
safety reasons, it is advisable to limit the maximum mixed water temperature to 120ºF.
Installation
NOTE TO INSTALLER: The Caleffi MixCal series 521 thermostatic mixing valve should be installed
by qualified personnel, in accordance with local codes and ordinances. It is the responsibility of
the installer to properly select, install and adjust this thermostatic mixing valve as specified in these
instructions.
Before installing a Caleffi MixCal series 521 thermostatic mixing valve, the system must be
inspected to ensure that it’s operating conditions are within the range of the thermostatic mixing
valve checking, for example, the supply temperature, supply pressure, etc.
Systems where the Caleffi MixCal series 521 thermostatic mixing valve is to be installed must
be drained and cleaned out to remove any dirt or debris which may have accumulated during
installation. Failure to remove dirt or debris may affect performance and the manufacturer’s product
guarantee. The installation of filters of appropriate capacity at the inlet of the water from the mains
supply is always advisable. In area which are subject to highly aggressive water, arrangements must
be made to treat the water before it enters the valve.
Caleffi MixCal series 521 thermostatic mixing valves must be installed in accordance with the
diagrams in this manual, taking into account all current applicable standards.
Caleffi Mix Cal series 521 thermostatic mixing valves can be installed in any position, either vertical
or horizontal.
The following are shown on the mixer body:
– Hot water inlet, color red and marker “HOT”.
– Cold water inlet, color blue and marker “COLD”.
– Mixed water outlet, marker “MIX”.
M
I
N
M
A
X
7
1
2
3
Locking the setting
Position the handle to the number required
with respect to the index point. Unscrew the
head screw, pull off the handle and reposition
it so that the handle fits into the internal slot
of the knob. Tighten the head screw.
Index
Point
5
Instantaneous production of hot water
Caleffi MixCal 521 series thermostatic mixing valves may be used with boilers or heaters providing
instantaneous hot water as long as the heater is the type which is capable of modulating its output
to handle low demand. A small amount of storage or piping length between the heat exchanger
and mixing valve will improve stability of water delivery temperature.
31 2
1
3
5
2
VA LV E BODY
UNION NUT , Quantity 3 per valve
INLET PORT MALE TAILPIECE
WITH INTEGRAL CHECK VA LV E
Quantity 2 per valve
INLET POR T CONIC FILTER,
Quantity 2 per valve
6OUTLET PORT T AILPIECE,
Quantity 1 per valve
4CHECK VALVE O-RING
2 5
5
6
3
4
4
(SWEAT TAILPIECE)
7Posi-Stop™ UNION SEALS, on body outlet ports
7
7
6
Check valves
In order to prevent undersirable backsiphonage, separate check valves should be installed in
systems with code “521 A” model thermostatic mixing valves (these models do not contain integral
check valves in the hot and cold inlet ports). As a convenience for easier installations, the Caleffi
code “521 AC” model series thermostatic mixing valves include integral check valves in the hot and
cold inlet ports.
NOTE TO INSTALLER: DO NOT TEST FIT OR INSTALL CHECK VALVES BEFORE SOLDERING. IF
INSTALLED, REMOVAL WILL REQUIRE DAMAGING THE CHECK VALVE AND IT WILL NO LONGER
BE USABLE.
The diagram below shows the order in which everything goes together. Note that the check valves
are installed on the hot and cold inlets, the mixed outlet does not require a check valve. Note that the
O-ring is installed on to the groove of the check valve.
After soldering the tailpieces into place, slide in the check valve into the tailpiece with o-ring going in
first. It will click into place and then the screen will fit into the groove of the tailpiece with the domed
end facing the mixing valve. Once the check valve and screen is installed in the tailpiece, insert the
tailpiece into the union nut, thread on to body outlet port and tighten
down the union nut until
metal meets metal to compress the Posi-Stop union seal.
Commissioning
The special purpose of the thermostatic mixing valve must be commissioned in accordance with cur-
rent standards by qualified personnel using temperature measuring equipment. Caleffi MixCal codes
52141_A and AC, 52151_A and AC, and 52161_A, AC with integral outlet port temperature gauges
provide a time-saving temperature setting process to get close to the desired temperture. Use of a
digital thermometer is recommended for determining the final setting of the mixed water temperature.
NOTE: Gauge adapters with 2” diameter, 30 - 210ºF (0 - 100ºC) scale, code NA10328 (1/2” sweat),
NA10056 (3/4” sweat) or NA10058 (1” sweat) can be separately purchased and field installed to the
Caleffi MixCal series 521 models sold without the integral gauge adapters.
After installation, the valve must be tested and commisioned in accordance with instructions given
below, taking into account current applicable standards.
1) Ensure that the system is clean and free from dirt or debris before commissioning the thermostatic
mixing valve.
2) It is recommended that the temperature is set using a suitable calibrated digital thermometer. The
valve must be commissioned by measuring the temperature of the mixed water emerging at the
point of use.
3) The maximum outlet temperature from the valve must be set taking account of the fluctuations
due to simultaneous use. It is essential for these conditions to be stabilised before commissioning.
4) Adjust the temperature using the adjusting knob on the valve. For safety reasons. it is advisable to
limit the maximum mixed water temperature to 120ºF in domestic hot water systems.
MIX
3
2
4
SUPPLY
HOTCOLD
MIX
BOILER
SUPPLY
MIX
3
2
4
MIX
3
2
4
Safety relief valve
Check valve
Isolation valve
Expansion vessel
Filter
Pump
*
*
*
*
*
*
WATER
HEATER
WATER
HEATER
CALEFFI
CALEFFI
CALEFFI
CALEFFI
10
0
8
6
4
2
10
0
8
6
4
2
CALEFFI
CALEFFI
10
0
8
6
4
2
10
0
8
6
4
2
10
0
8
6
4
2
10
0
8
6
4
2
Radiant panels heating system
MIX
3
2
4
SUPPLY
HOTCOLD
MIX
BOILER
SUPPLY
MIX
3
2
4
MIX
3
2
4
Safety relief valve
Check valve
Isolation valve
Expansion vessel
Filter
Pump
*
*
*
*
*
*
WATER
HEATER
WATER
HEATER
CALEFFI
CALEFFI
CALEFFI
CALEFFI
10
0
8
6
4
2
10
0
8
6
4
2
CALEFFI
CALEFFI
10
0
8
6
4
2
10
0
8
6
4
2
10
0
8
6
4
2
10
0
8
6
4
2
*MixCal series 521 thermostatic mixing valves with inlet check valves, “AC” models, can be used
instead of separately installed check valves.
**Refer to principle of operation on page 8.
SUPPLY
MIX
3
2
4
WATER
HEATER
Safety relief valve
Check valve
Isolation valve
Expansion vessel
Filter
Pump
Globe valve
Domestic hot water system
without recirculation
Domestic hot water system
with recirculation**
CALEFFI
3
2
4
COLD
HOT
HOT/RED COLD/BLUE
MIX
MIX
3
2
4
SUPPLY
HOTCOLD
MIX
BOILER
SUPPLY
MIX
3
2
4
MIX
3
2
4
Safety relief valve
Check valve
Isolation valve
Expansion vessel
Filter
Pump
*
*
*
*
*
*
WATER
HEATER
WATER
HEATER
CALEFFI
CALEFFI
CALEFFI
CALEFFI
10
0
8
6
4
2
10
0
8
6
4
2
CALEFFI
CALEFFI
10
0
8
6
4
2
10
0
8
6
4
2
10
0
8
6
4
2
10
0
8
6
4
2
Application Diagrams
Temperature adjustment
The temperature is set to the required value by means of the knob with a graduated scale, on the
top of the valve.
Pos. Min. 1 2 3 4 5 6 7 Max.
T (°F) 81 90 100 111 120 127 136 145 152
T (°C) 27 32 38 44 49 53 58 63 67
with: T
HOT = 155°F (68°C), with: T
cold = 55°F (13°C), P = 43 psi (13 bar)
7
2
1
8
Recirculation with point-of-distribution thermostatic mixing valves
For domestic recirculating water systems, that include a single ASSE 1017 point-of-distribution
thermostatic mixing valve, such as the Caleffi MixCal™ 521 series, the piping installation in the
application drawing on page 7 is recommended.
In any recirculating hot water distribution system there will be times when the circulator is
operating, but no hot water is being drawn at the fixtures. Under this condition, heat continually
dissipates from the piping forming the recirculation loop. If the loop is relatively short, and well
insulated, the rate of heat loss should be very small. If the loop is long, and uninsulated, the
rate of heat loss could be substantially greater.
To maintain the recirculating water at the desired delivery temperature the heat lost from the
loop must be replaced. This requires some water flow between the loop and the hot water
source. Ideally, this flow is adjusted so that the rate of heat transfer from the hot water source
to the loop exactly balances the rate of heat loss from the loop’s piping.
The figure (below) shows a “bypass valve” (1), and “return valve” (2), which regulate how
much warm water from the return side of the recirculating loop flows back to the storage tank.
When there is no demand for hot water at the fixtures, the flow of return water to the tank
will equal the rate of hot water flow from the tank to the inlet port of the mixing valve. Ideally,
this flow should be adjusted so that the rate of heat transfer from the tank to the recirculating
loop exactly balances the rate of heat loss from the recirculating loop. This allows the water
temperature leaving themixing valve to remain stable.
The bypass valve (1) and possibly the return valve (2) must be adjusted when there is no
domestic water draw on the recirculating loop (when all the fixtures are off). Begin with the
bypass valve (1) fully closed, and the return valve (2) fully open. Turn on the recirculating
circulator and let it run for several minutes. The supply water temperature leaving the mixing
valve will likely be lower than the setting of the valve, since there is no return flow to the tank
thus, no hot water to the hot port of the mixing valve.
Slowly open the bypass valve (1) and monitor the temperature leaving the mixing valve. It will
likely begin rising as some water returns to the tank, and an equal flow of hot water moves
from the tank to the hot port of the mixing valve. When the temperature leaving the mixing valve
remains stable, and is at or very close to the temperature set on the mixing valve, the bypass
valve is correctly set.
The return valve (2) can remain fully open unless a situation occurs where the bypass valve (1)
is fully open, but the temperature leaving the mixing valve is still too low. If this occurs, partially
close the return valve (2) to add flow resistance. This forces more flow through the bypass valve
(1). Repeat the previously described procedure of slowly opening the bypass valve (1) until the
water temperature leaving the mixing valve is stable.
Replacement ttings
Replacement parts
Replacement body.
Meets requirements of
NSF/ANSI/CAN 372.
Certified to: ASSE
1017/CSA B125.3,
Low lead, by ICC-ES
file PMG-1360.
521101A.........................1" male union thread
Point of distribution
mixed temperature
gauge adaptor fits
MixCal™ 521 series
mixing valves. Threaded
union mounting
replaces existing mixed
outlet with ¾" or 1"
sweat pipe connection.
NA10328..........................½" sweat with gauge
NA10056..........................¾" sweat with gauge
NA10058...........................1" sweat with gauge
NA10358 ................1" union thread with gauge
688003A.....Replacement gauge w/ pocket well
R39591..............................Replacement gauge
NA10498.............................Pocket well, plated
Removable gauge fits into temperature well.
Gauge dial is 2” diameter and dual-scale from
30—210ºF (0—100ºC).
9
Refer to the current Caleffi Plumbing and Hydronics Catalog for replacement union nuts
and tailpieces by size and connection style. NOTE: Sealing washers are not required for
MixCal 521 series thermostatic mixing valves shipped after July 2023.
10
Troubleshooting
Under normal operating conditions the Caleffi 521 thermostatic mixing valve will provide a very high level of
performance. However, in some circumstances, where the following maintenance schedule is not followed
problems may arise.
Recommended maintenance schedule:
Tests should be conducted regularly to monitor the thermostatic mixing valve performance, as deterioration
of performance could indicate that the valve and/or the system require maintenance. If, during these
tests, the temperature of the mixed water has changed significantly in comparison with the previous test,
the details given in the installation and commissioning sections should be checked and maintenance
conducted.
The following should be checked regularly to ensure that the optimum performance levels of the valve are
maintained. Check every 12 months at least, or more often if necessary.
1) Check and clean the system filters.
2) Check that any check valves positioned upstream of the Caleffi thermostatic mixing valve are operating
correctly, without problems caused by impuritites.
3) Limescale can be removed from internal components of the thermostatic mixing valve by immersion in
a suitable de-scaling fluid.
4) When the components which can be maintained have been checked, commission the valve.
11
HOT
COLD
MIX
MIN
M
A
X
7
1
2
A
FE
D
B B
C
A
A
HOT
COLD
MIX
MIN
M
A
X
7
1
2
A
FE
D
B B
C
A
A
MIX
E
D
A
30
50
70
90
110130
150
170
190
210
ϒF
MIX
E
D
A
30
50
70
90
110130
150
170
190
210
ϒF
Dimensions
Code A B C D* E F Wt. (lb.)
NPT Threaded connections
521400A 1⁄2" 25⁄8" 51⁄4" 6" 33⁄8" 25⁄8" 2.4
521400AC 1⁄2" 25⁄8" 51⁄4" 6" 33⁄8" 25⁄8" 2.4
521410A** 1⁄2" 25⁄8" 51⁄4" 73⁄8" 4¾" 25⁄8" 2.9
521410AC** 1⁄2" 25⁄8" 51⁄4" 73⁄8" 4¾" 25⁄8" 2.9
521500A 3⁄4" 25⁄8" 51⁄4" 6" 33⁄8" 25⁄8" 2.4
521500AC 3⁄4" 3" 6" 6" 33⁄8" 25⁄8" 2.4
521510A** 3⁄4" 25⁄8" 51⁄4" 8" 53⁄8" 25⁄8" 2.9
521510AC** 3⁄4" 3" 6" 8" 53⁄8" 25⁄8" 2.9
521600A 1" 27⁄8" 53⁄4" 61⁄4" 3¾" 25⁄8" 2.4
521600AC 1" 31⁄16" 61⁄8" 61⁄4" 3¾" 25⁄8" 2.4
521610A** 1" 27⁄8" 53⁄4" 75⁄8" 51⁄8" 25⁄8" 2.9
521610AC** 1" 31⁄16" 61⁄8" 75⁄8" 51⁄8" 25⁄8" 2.9
Press connections
521406A ½" 29⁄16" 51⁄8" 6" 33⁄8" 25⁄8" 2.4
521406AC ½" 39⁄16" 67⁄8" 6" 33⁄8" 25⁄8" 2.5
521416A** ½" 29⁄16" 51⁄8" 81⁄4" 55⁄8" 25⁄8" 2.9
521416AC** ½" 39⁄16" 67⁄8" 81⁄4" 55⁄8" 25⁄8" 3.0
521506A ¾" 213⁄16" 55⁄8" 8½" 57⁄8" 25⁄8" 2.4
521506AC ¾" 43⁄16" 83⁄8" 8½" 57⁄8" 25⁄8" 2.5
521516A** ¾" 213⁄16" 55⁄8" 8½" 57⁄8" 25⁄8" 2.9
521516AC** ¾" 43⁄16" 83⁄8" 8½" 57⁄8" 25⁄8" 3.0
521606A 1" 215⁄16" 57⁄8" 65⁄16" 311⁄16" 25⁄8" 2.6
521606AC 1" 45⁄16" 85⁄8" 65⁄16" 311⁄16" 25⁄8" 3.1
521616A** 1" 215⁄16" 57⁄8" 85⁄8" 6" 25⁄8" 3.1
521616AC** 1" 45⁄16" 85⁄8" 85⁄8" 6" 25⁄8" 3.5
C at the end of the code are models with integral inlet port check valves.
*At minimum temperature position on adjusting knob.
**Model with integral outlet temperature gauge.
Laylength (press):
sz ½ & ¾ inch: 3 5/8 "
sz 1 inch: 4 1/8 "
sz 1 inch w/ checks: 7¼"
30
50
70
90
110 130
150
170
190
210
˚F
10 0
˚C
80
60
40
20
0
PEX crimp connections
521407A 1⁄2" 31⁄4" 61⁄2" 61⁄2" 4" 25⁄8" 2.4
521417A** 1⁄2" 31⁄4" 61⁄2" 61⁄2" 4" 25⁄8" 2.5
521407AC 1⁄2" 31⁄4" 61⁄2" 61⁄2" 4" 25⁄8" 2.9
521417AC** 1⁄2" 31⁄4" 61⁄2" 83⁄4" 61⁄8" 25⁄8" 2.9
521507A 3⁄4" 31⁄4" 61⁄2" 61⁄2" 4" 25⁄8" 2.4
521517A** 3⁄4" 31⁄4" 61⁄2" 61⁄2" 4" 25⁄8" 2.5
521507AC 3⁄4" 31⁄4" 61⁄2" 61⁄2" 4" 25⁄8" 2.9
521517AC** 3⁄4" 31⁄4" 61⁄2" 83⁄4" 61⁄8" 25⁄8" 2.9
521607A 1" 31⁄4" 61⁄2" 61⁄2" 4" 25⁄8" 2.4
521617A** 1" 31⁄4" 61⁄2" 61⁄2" 4" 25⁄8" 2.5
521607AC 1" 31⁄4" 61⁄2" 61⁄2" 4" 25⁄8" 2.9
521617AC** 1" 31⁄4" 61⁄2" 83⁄4" 61⁄8" 25⁄8" 2.9
C at the end of the code are models with integral inlet port check valves.
*At minimum temperature position on adjusting knob.
**Model with integral outlet temperature gauge.
Code A B C D* E F Wt. (lb.)
Sweat connections
521409A 1⁄2" 21⁄4" 41⁄2" 55⁄8" 31⁄8" 25⁄8" 2.4
521419A** 1⁄2" 21⁄4" 41⁄2" 7" 41⁄2" 25⁄8" 2.9
521409AC 1⁄2" 27⁄8" 53⁄4" 55⁄8" 31⁄8" 25⁄8" 2.4
521419AC** 1⁄2" 27⁄8" 57⁄8" 7" 41⁄2" 25⁄8" 2.9
521509A 3⁄4" 21⁄2" 5" 513⁄16" 31⁄4" 25⁄8" 2.4
521519A** 3⁄4" 21⁄2" 5" 713⁄16" 51⁄4" 25⁄8" 2.9
521509AC 3⁄4" 31⁄16" 61⁄8" 513⁄16" 31⁄4" 25⁄8" 2.4
521519AC** 3⁄4" 31⁄16" 61⁄8" 713⁄16" 51⁄4" 25⁄8" 2.9
521609A 1" 31⁄16" 61⁄8" 67⁄16" 37⁄8" 25⁄8" 2.4
521619A** 1" 31⁄16" 61⁄8" 713⁄16" 51⁄4" 25⁄8" 2.9
521609AC 1" 31⁄4" 61⁄2" 67⁄16" 37⁄8" 25⁄8" 2.4
521619AC** 1" 31⁄4" 61⁄2" 713⁄16" 51⁄4" 25⁄8" 2.9
HOT
COL D
MIX
MIN
M
A
X
7
1
2
A
FE
D
B B
C
A
A
HOT
COL D
MIX
MIN
M
A
X
7
1
2
AFE
D
B B
C
A
A
MIX
E
D
A
30
50
70
90
110 130
150
170
190
210
F
MIX
E
D
A
30
50
70
90
110 130
150
170
190
210
F
Dimensions
30
50
70
90
110 130
150
170
190
210
˚F
10 0
˚C
80
60
40
20
0
12
HOT
COL D
MIX
MIN
M
A
X
7
1
2
A
FE
D
B B
C
A
A
HOT
COL D
MIX
MIN
M
A
X
7
1
2
A
FE
D
B B
C
A
A
MIX
E
D
A
30
50
70
90
110 130
150
170
190
210
F
MIX
E
D
A
30
50
70
90
110 130
150
170
190
210
F
HOT
COL D
MIX
MIN
M
A
X
7
1
2
FE
D
B B
C
A
MIX
E
D
30
50
70
90
110 130
150
170
190
210
F
A
A
A
HOT
COL D
MIX
MIN
M
A
X
7
1
2
FE
D
B B
C
A
MIX
E
D
30
50
70
90
110 130
150
170
190
210
F
A
A
A
PEX expansion connections
Code A B C D* E F Wt. (lb)
521408A ½" 33⁄8" 63⁄4" 67⁄16" 313⁄16" 25⁄8" 2.4
521418A** ½" 33⁄8" 63⁄4" 713⁄16" 53⁄16" 25⁄8" 2.5
521408AC ½" 33⁄8" 63⁄4" 67⁄16" 313⁄16" 25⁄8" 2.9
521418AC** ½" 33⁄8" 63⁄4" 713⁄16" 53⁄16" 25⁄8" 2.9
521508A ¾" 33⁄16" 63⁄8" 7¼" 45⁄8" 25⁄8" 2.4
521518A** ¾" 33⁄16" 63⁄8" 9¼" 65⁄8" 25⁄8" 2.5
521508AC ¾" 311⁄16" 73⁄8" 7¼" 45⁄8" 25⁄8" 2.9
521518AC** ¾" 311⁄16" 73⁄8" 9¼" 65⁄8" 25⁄8" 2.9
521608A 1" 39⁄16" 71⁄8" 75⁄8" 5" 25⁄8" 2.4
521618A** 1" 39⁄16" 71⁄8" 9" 63⁄8" 25⁄8" 2.5
521608AC 1" 41⁄16" 81⁄8" 75⁄8" 5" 25⁄8" 2.9
521618AC** 1" 41⁄16" 81⁄8" 9" 63⁄8" 25⁄8" 2.9
C at the end of the code are models with integral inlet port check valves.
*At minimum temperature position on adjusting knob.
**Model with integral outlet temperature gauge.
30
50
70
90
110 130
150
170
190
210
˚F
10 0
˚C
80
60
40
20
0
Dimensions
13
14
NOTES
NOTES
15
16
Symptoms Cause Corrective action
Hot water at the cold taps a) Operation of check valve is
hindered; Check valve is not
sealing correctly.
b) Check valves not fitted.
- Replace faulty check valve
Fluctuating mixed water
temperature
a) Erratic supply temperatures at
the inlet of the valve.
b) Starvation of the water
supplies at the inlets of the valve.
c) Incorrect commissioning of the
valve.
- Restore inlet conditions within
the limits of the valve.
Erratic flow of water from
the valve
a) Insufficient water supplies
b) Fluctuations in the supply
pressures/temperatures.
c) Adverse effect created by other
draw off points on the system
- Stabilize inlet supply condi-
tions.
No flow of water from the
valve
a) In-line filers blocked.
b) Insufficient supply pressures.
c) Debris obstructing valve
operation.
- Clean filters
- Resore inlet supplies
- Clean debris or scale from
the valve.
Caleffi North America, Inc.
3883 West Milwaukee Road
Milwaukee, WI 53208
T: 414.238.2360 F: 414.238.2366
06-2023
For Technical Support call 1-414-338-6338, or
email techsupport.us@calef.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
dans d''autres langues
- English: Caleffi 38476 Operating instructions
Documents connexes
-
Caleffi North America 38476 Guide d'installation
-
Caleffi 521516AC Guide d'installation
-
-
-
-
-
-
-
-