Sollae Systems SIG-5430 Manuel utilisateur

Sollae Systems

https://www.ezTCP.com

4-Port Analog Input I/O Gateway

SIG-5430 User Manual

Version 1.2

SIG-5430 User Manual Ver. 1.2

- 1 -

https://www.ezTCP.com

This symbol, found on your product or on its packaging, indicates that

this product should not be treated as household waste when you wish to

dispose of it. Instead, it should be handed over to an applicable collection

point for the recycling of electrical and electronic equipment. By ensuring

this product is disposed of correctly, you will help prevent potential negative

consequences to the environment and human health, which could otherwise be caused by

inappropriate disposal of this product. The recycling of materials will help to conserve

natural resources. For more detailed information about the recycling of this product,

please contact your local city office, household waste disposal service or the retail

store where you purchased this product.

Note:

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

SIG-5430 User Manual Ver. 1.2 
 
- 2 - 
https://www.ezTCP.com 
 
Contents 
Overview ....................................................... - 4 - 
1 Introduction ........................................................ - 4 - 
2 Features ............................................................ - 4 - 
3 Specification ....................................................... - 5 - 
4 Interface ........................................................... - 6 - 
4.1 Power .................................................................. - 6 - 
4.2 Ethernet ............................................................... - 7 - 
4.3 Analog Input Port ...................................................... - 7 - 
4.4 LED .................................................................... - 8 - 
4.5 Function Button ........................................................ - 8 - 
4.6 Setup Port ............................................................. - 8 - 
Preparation .................................................... - 9 - 
1 Installing the Setting Tool ......................................... - 9 - 
2 Connecting a Product ................................................ - 9 - 
3 Searching Devices ................................................... - 9 - 
4 Logging in .......................................................... - 9 - 
Settings ...................................................... - 10 - 
1 Network ............................................................ - 10 - 
1.1 Obtain an IP address automatically ..................................... - 10 - 
1.2 Use a Static IP address................................................ - 11 - 
2 General ............................................................ - 12 - 
2.1 Comments .............................................................. - 12 - 
2.2 TCP ................................................................... - 12 - 
2.3 Modbus ................................................................ - 13 - 
2.4 Analog Input .......................................................... - 13 - 
3 Security ........................................................... - 14 - 
3.1 Password .............................................................. - 14 - 
3.2 Certificate ........................................................... - 14 - 
3.3 spFinder .............................................................. - 14 - 
3.4 Client ID ............................................................. - 15 - 
Management .................................................... - 16 - 
1 Checking Status .................................................... - 16 - 
1.1 Product Information ................................................... - 16 - 
1.2 Communication Status .................................................. - 17 - 
1.3 Timeout ............................................................... - 18 - 
1.4 Copy Status ........................................................... - 18 - 
2 Firmware Change .................................................... - 19 - 
2.1 Online Upgrade ........................................................ - 19 - 
2.2 Manual Upgrade ........................................................ - 20 - 

SIG-5430 User Manual Ver. 1.2 
 
- 3 - 
https://www.ezTCP.com 
 
3 Console ............................................................ - 21 - 
3.1 Output Tab ............................................................ - 21 - 
3.2 FW Log Tab ............................................................ - 22 - 
3.3 Timeout ............................................................... - 22 - 
4 Export/Import Setting Values ....................................... - 22 - 
5 Factory Reset ...................................................... - 23 - 
Register Map .................................................. - 24 - 
1 Read Only .......................................................... - 24 - 
1.1 Analog Input Value Register ............................................ - 24 - 
1.2 Minimum Analog Input Value Register .................................... - 24 - 
1.3 Maximum Analog Input Value Register .................................... - 24 - 
1.4 Device Information Register ............................................ - 25 - 
2 Read / Write ....................................................... - 26 - 
2.1 Reset Analog Input Min/Max Value Register .............................. - 26 - 
Technical Support and Warranty ................................ - 27 - 
1 Technical Support .................................................. - 27 - 
2 Warranty ........................................................... - 27 - 
2.1 Free Repair Services .................................................. - 27 - 
2.2 Charged Repair Services................................................ - 27 - 
Precaution and Exemption from Liability ....................... - 28 - 
1 Precaution ......................................................... - 28 - 
2 Exemption from Liability ........................................... - 29 - 
2.1 English version ....................................................... - 29 - 
2.2 French version ........................................................ - 30 - 
Revision History .............................................. - 32 - 
 
  

SIG-5430 User Manual Ver. 1.2

- 4 -

https://www.ezTCP.com

1 Overview

1.1 Introduction

SIG-5430 is an industrial I/O Gateway consisting of 4 analog input ports. Users

can remotely monitor analog values of sensors connected to this product by using

Modbus/TCP.

1.2 Features

⚫ 4 analog input ports: voltage or current

⚫ Support Modbus/TCP

⚫ Support multiple TCP connection (Max. 4 channels)

⚫ Support a 1-bit ADC function for the

Internet Switch

⚫ Industrial temperature range (-40℃ ~ +85℃)



Internet Switch: A configuration that connects devices to each other without an

HMI to transmit digital signals in both directions

SIG-5430 User Manual Ver. 1.2

- 5 -

https://www.ezTCP.com

1.3 Specification

Analog Input

Input Type

Voltage (0V ~ 5V) or Current (4mA ~ 20mA / 0mA ~ 20mA)

Resolution

12 bits

Number of Ports

4 ports

Network Physical Interface

Network Interface

10Base-T/100Base-TX Ethernet (RJ45)

Ethernet Speed Auto Sense

1:1 or Cross-over Cable Auto Sense

Software Functions

Protocols

IPv4/IPv6 Dual Stack,

TCP/UDP, ICMP, DHCP, mDNS, Modbus/TCP, SSL/TLS

Indicators

LED

MTX, MRX

Management

spFinder

Configuration and Monitoring Tool

Security

Password

Dimension

Size

94mm x 57mm x 23mm

Weight

about 62g

Operating Environment

Input Voltage

DC5V±0.2V

Protection

Reverse Voltage Protection / Surge Protection

Current Consumption

typically, 160mA

Operating Temperature

-40℃ ~ +85℃

Storage Temperature

-40℃ ~ +85℃

Certificate

KC

Registration (KN 32, KN 35)

CE

EMC 2014/30/EU, RoHS 2011/65/EU

FCC

FCC Part 15 Subpart B, Class A

Table 1-1 Specification

SIG-5430 User Manual Ver. 1.2

- 6 -

https://www.ezTCP.com

1.4 Interface

Figure 1-1 Interface

1.4.1 Power

SIG-5430 requires DC5V power supply whose specification is as follows:

Figure 1-2 Power

SIG-5430 User Manual Ver. 1.2

- 7 -

https://www.ezTCP.com

1.4.2 Ethernet

SIG-5430 provides 10/100Mbps Ethernet. The pin assignment is as follows:

Figure 1-3 Ethernet

1.4.3 Analog Input Port

This port is interfaced with a 3.5mm pitch 8-pole terminal block.

Figure 1-4 Analog Input Port

⚫ Port Specification

Division

Value

Number of ports

4

Input mode

Voltage (0 ~ 5V) or Current (4 ~ 20mA / 0 ~ 20mA)

Resolution

12-bit (0 ~ 4,095)

Table 1-2 Port Specification

SIG-5430 User Manual Ver. 1.2

- 8 -

https://www.ezTCP.com

1.4.4 LED

SIG-5430 provides 4 LEDs.

Figure 1-5 4 LEDs

LED operations according to each state are as follows:

When the script is running: RUN

When a network is not connected: LINK

When a network is connected: LINK

When a TCP connection is NOT established: MTX & MRX

When sending data to the TCP: MTX

When receiving data from the TCP: MRX

1.4.5 Function Button

This button is used to implement a factory reset.

1.4.6 Setup Port

This port is used for making a connection with a PC via USB cable.

SIG-5430 User Manual Ver. 1.2

- 9 -

https://www.ezTCP.com

2 Preparation

2.1 Installing the Setting Tool

You need a program which is called spFinder to use this product. Download the

program on our web site and install it on your PC.

Functions of the spFinder are as follows:

⚫ Searching products connected via network and USB

⚫ Setting products

⚫ Monitoring status of products

2.2 Connecting a Product

Connect a product with your PC via a LAN cable or a USB cable. In the case of

using a LAN cable, note that your PC and the product should be on the same local

area network.

2.3 Searching Devices

Run spFinder on your PC and press the search button. If you select the product

found, the setup menu appears on the right.

2.4 Logging in

Before accessing the searched product, you need to log in first. The default ID

and password are as follows:

Division

Default Values

ID

sig-5430

Password

sig-5430

Table 2-1 The default values of ID and password



If you search the product via network and it has the default value for a password,

spFinder automatically processes the login.

SIG-5430 User Manual Ver. 1.2

- 10 -

https://www.ezTCP.com

3 Settings

3.1 Network

3.1.1 Obtain an IP address automatically

This product can automatically obtain an IP address by DHCP. A DHCP server is

required to use this.

Figure 3-1 Obtain an IP address automatically

⚫ Select the [Obtain an IP address automatically].

⚫ Check the [Obtain DNS server address automatically] and click the [Save]

button.

SIG-5430 User Manual Ver. 1.2

- 11 -

https://www.ezTCP.com

3.1.2 Use a Static IP address

You can set a static IP address to this product.

Figure 3-2 Use a static IP address

⚫ Select the [Use static IP address].

⚫ Set the [Local IP address], [Subnet mask], [Gateway IP address] and [DNS IP

address].

⚫ Click the [Save] button.

SIG-5430 User Manual Ver. 1.2

- 12 -

https://www.ezTCP.com

3.2 General

Figure 3-3 General

3.2.1 Comments

This setting is for storing the product description. The maximum setting size of

this item is 32 bytes.

3.2.2 TCP

⚫ Connection Mode

This item selects the TCP connection method. You can choose between TCP Server

and TCP Client. The default is TCP Server.

⚫ Peer Address

This item is to enter an IP address or a host name of the host to connect to.

It is valid only when the Connection Mode is set to TCP Client.

⚫ Port

This item is to set the port number for the TCP connection. It can be set

between 0 and 65535. The default is 502.

⚫ Multiple Connection

This item enables multiple TCP connections. When this item is set to Disable,

only one TCP session (TCP0) can be used. If this item is set to Enable, the

rest of TCP sessions (TCP1 to 3) are activated. It means you can use 4

sessions at the same time.

⚫ Connection Timeout (Unit: sec)

This item is to set a timeout for terminating a TCP connection. If there is no

valid Modbus/TCP data communication during the time set in this item, the TCP

SIG-5430 User Manual Ver. 1.2

- 13 -

https://www.ezTCP.com

connection is terminated. The unit is seconds and can be set between 0 and

3600. Default value is 0.

3.2.3 Modbus

⚫ Modbus Type

This item is to set the Modbus type. This product allows the Slave only.

3.2.4 Analog Input

⚫ Mode

This item selects the analog input type. The setting value can be selected

among [0 ~ 5V], [4 ~ 20mA] and [0 ~ 20mA]. The default value is [0 ~ 5V].

⚫ 1-bit ADC

This function converts analog input value into 1-bit digital value. This

function is only used in Internet switch.

⚫ 1-bit ADC: High Ref.

This is the reference value for judging HIGH in 1-bit ADC. Analog input value

greater than this value is judged as HIGH. The setting unit follows the

setting of Mode and allows setting up to 5 decimal places.

⚫ 1-bit ADC: Low Ref.

This is the reference value for judging LOW in 1-bit ADC. Analog input value

smaller than this value is judged as LOW. The setting unit follows the setting

of Mode and allows setting up to 5 decimal places.

SIG-5430 User Manual Ver. 1.2

- 14 -

https://www.ezTCP.com

3.3 Security

Figure 3-4 Security

3.3.1 Password

Both ID and password are required to access this product. Note that changing the

default password to another is highly recommended for security. The password should

be longer than 8 characters.

⚫ Input a password to use to [Password] and [Confirm password].

⚫ Click the [Save] button.

3.3.2 Certificate

This is not available for this product.

3.3.3 spFinder

These items are related to spFinder use.

⚫ Local search

If this item is not checked, you will not be able to search for or connect to

the product on your local network. This item can be set only when the product

is connected via USB.

⚫ Network connection

If this item is not checked, the product cannot be searched on the local

network and the product cannot be connected on the local or remote network.

This item can be set only when the product is connected via USB.

SIG-5430 User Manual Ver. 1.2

- 15 -

https://www.ezTCP.com

⚫ Remote access

If this item is checked, the product can be connected from the remote network.

For security, this item is unchecked by default.

3.3.4 Client ID

This is NOT available for this product.

SIG-5430 User Manual Ver. 1.2

- 16 -

https://www.ezTCP.com

4 Management

4.1 Checking Status

This is a function to view the current status of the product. Information in the

[Status] window is automatically updated every second. After searching and

connecting the product with spFinder, press the [Status] button to display this

window. When you open this window, the spFinder connects to the product and keeps

the connection until you close the window or time out. While the connection is

maintained, other hosts cannot access the product using the spFinder.

4.1.1 Product Information

⚫ Product Information Window

This area shows some major information of your product.

Figure 4-1 Product Information Window

⚫ Product Information List

Item

Description

Product name

Pkgware

Model name, package version, Firmware version

File name

Uptime

Elapsed time since it boots up (day / hour:min:sec)

IPv4

Assigned IPv4 address

Subnet

Assigned subnet mask

Gateway

Assigned gateway IP address

DNS

Assigned DNS server IP address

Table 4-1 Product Information List

SIG-5430 User Manual Ver. 1.2

- 17 -

https://www.ezTCP.com

4.1.2 Communication Status

⚫ Communication Status Window

This area shows some communication status of your product. This area is

refreshed every second.

Figure 4-2 Communication Status Window

⚫ TCP STATE

Status

Description

LISTEN

Listen

CLOSED

Disconnected

CONNECTED

Connected (IP and port of the connected host will be shown)

CONNECTING

Connecting

DISCONNECTING

Disconnecting

Table 4-2 TCP STATE

⚫ MODBUS STATISTICS

Item

Description

RX0~3

Statistics of incoming data from TCP: Query, Error, Discard

TX0~3

Statistics of outgoing data to TCP: Reply, Error

Query

The number of query frames received by the master

Error

The number of invalid frames among sent/received frames

Discard

The number of discarded frames not meet the protocol

Reply

The number of response frames sent to the master

Table 4-3 MODBUS STATISTICS

SIG-5430 User Manual Ver. 1.2

- 18 -

https://www.ezTCP.com

⚫ DEVICE STATISTICS

Item

Description

TCP0~3

The byte count of TCP data: TX, RX

TX

The byte count of outgoing TCP data

RX

The byte count of incoming TCP data

AI0~3

Current value of each analog input port (min, max)

VDI

Current 1-bit ADC value of each analog input port

Table 4-4 DEVICE STATISTICS

4.1.3 Timeout

This is the timeout display function that appears in the upper right of the status

window. When this time reaches zero, the connection between spFinder and the product

is lost. The initial value is 30 minutes. If you move the mouse pointer in the

internal area of the status window, the timer is reset to the initial value again.

4.1.4 Copy Status

Clicking the button copies all information displayed in the current status window

to the clipboard.

SIG-5430 User Manual Ver. 1.2

- 19 -

https://www.ezTCP.com

4.2 Firmware Change

New firmware can be released when adding functions or fixing bugs. If you are

using old firmware, you can upgrade it to the latest version. Firmware can be

upgraded online or manually via spFinder.

4.2.1 Online Upgrade

If you can access to the Internet by your PC, the Firmware can be upgraded online.

Figure 4-3 Online Upgrade

⚫ Search and Connect to your product by spFinder.

⚫ Click [Advanced] > [Firmware change] menu.

⚫ Click [Upgrade] button selecting [Automatic online upgrade] menu.

La page est en cours de chargement...

Sollae Systems SIG-5430 Manuel utilisateur

Sollae Systems SIG-5430 Manuel utilisateur

dans d''autres langues