Rointe Circe OVAL Le manuel du propriétaire

Marque: Rointe

Modèle: Circe OVAL

Taper: Le manuel du propriétaire

Ce manuel convient également à

Circe Oval electric

Circe electric oval

Models / Modelos / Modèle / Modellen

OVAL 482 | 532

MANUAL DE INSTALACIÓN Y USO

Página 18

MANUAL DE INSTALAÇÃO E UTILIZAÇÃO

Página 34

INSTRUCTIONS & INSTALLATION GUIDE

Page 02

INSTALLATIE- EN GEBRUIKERSHANDLEIDING

Bladzijde 66

MANUEL D’INSTALLATION ET D’UTILISATION

Page 50

Installation & safety precautions (EN 60335 Standards)

Before switching on the product, please read the “Installation & Safety Precautions” in detail rst to

ensure the correct operation of the product.

Installation precautions

The product is designed for household or residential use. You are advised to have the product installed

by an authorized professional installer. Make sure the product is properly connected to 230V.

ATTENTION

Children under 3 years of age should be kept out of reach of the appliance

unless continuously supervised. Children from the age of 3 years to 8

years should only switch the appliance on/off when it has been placed

or installed in its normal intended use position and when they have been

given supervision or instruction concerning use of the appliance in a safe

way and understand the hazards involved. Children from 3 years of age to

8 years of age should not plug in, adjust or clean the appliance or carry out

maintenance operations.

This appliance can be used by children aged from 8 years and above

and persons with reduced physical sensory or mental capabilities or lack

of experience and knowledge if they are supervised or have been given

instruction concerning use of the appliance in a safe way and understand

the hazards involved. Children should not play with the appliance. Cleaning

and user maintenance should not be carried out by children without

supervision. Children must be supervised at all times to ensure that they

do not interfere with the product.

This product is lled with a precise amount of special oil that does not

need any maintenance. Any repairs requiring the opening of the oil tank

must only be done by an ofcial Rointe installer or its after-sales service

personnel, who should also be notied should an oil leak be noticed. The

regulations on discarding oil when the heater is being disposed of must be

observed.

Do not cut the power supply cable under any circumstances in order to

avoid electrical risks and to guarantee the correct operation of the towel

rail.

Do not switch on the product if you notice any external damage when

unpacking or installing the towel rail. If the power cable is damaged, it

must be replaced by the manufacturer, its after-sales service or authorized

personnel in order to avoid any damage.

CIRCE OVAL

Do not spray or wet the product. During operation, keep the product

away from combustible materials such as curtains, furniture, etc. Do not

place anything other than clothes, towels or non-ammable fabrics on the

product.

The towel rail must be installed in such a way that the power plug is always

accessible. The power cable must never be in contact with the product

during operation.

CAUTION - Never touch the product with wet hands or any wet

body parts.

CAUTION - Some parts of this product may become very hot

and cause burns. Particular care should be taken when children

and vulnerable persons are present.

Contents

1. Technical Specications ..........................................................................................................................4

2. Product Installation........ .........................................................................................................................6

2.1. Mounting ..........................................................................................................................................6

2.2. Connecting instructions .................................................................................................................6

2.3. Specic regulations for bathrooms...............................................................................................7

3. Control panel description and functions...............................................................................................8

3.1. Control panel........................................................................................................................................8

3.2. Power and Stand-by........................................................................................................................8

3.3. Set temperature selection..............................................................................................................8

3.4. Consumption identication................................................................................................................9

3.5. Keypad lock.......................................................................................................................................9

3.6. MAX POWER mode..........................................................................................................................9

3.7. Remote control.....................................................................................................................................10

3.8. Troubleshooting.............................................................................................................................11

4. Maintenance & Cleaning............... .........................................................................................................12

5. Guarantee......................................... ......................................................................................................12

6. How to register your guarantee....... .......................................................................................................14

7. ERP Directive (EU) 2015/1188....... ..........................................................................................................16

1. Technical speciﬁcations (Models 482 & 522)

MODEL - 482 MM WIDTH STEEL

TCIV*48A080 TCIV*48A120

DIMENSIONS

Width (mm) 482 482

Height without control panel (mm) 800 1,200

Height with control panel (mm) 895 1,295

Depth (mm) 75 75

Installed depth (mm) 77 77

MECHANICAL CHARACTERISTICS

Stainless steel heating element

 

Thermal ﬂuid

 

Oval control panel

 

Infrared remote control

 

Finish Polished inox steel

ELECTRICAL CHARACTERISTICS

Nominal power (W) 300 300

Voltage (V) 230 V ~ 230 V ~

Current (A) 1.3 1.3

Class II

 

SAFETY & INSTALLATION

Installation kit included

 

Safety thermostat

 

Protection grade IP 44 IP 44

CIRCE OVAL

MODEL - 532 MM WIDTH STEEL

TCIV*53A080 TCIV*53A120

DIMENSIONS

Width (mm) 532 532

Height without control panel (mm) 800 1,200

Height with control panel (mm) 895 1,295

Depth (mm) 75 75

Installed depth (mm) 77 77

MECHANICAL CHARACTERISTICS

Stainless steel heating element

 

Thermal ﬂuid

 

Oval control panel

 

Infrared remote control

 

Finish Polished inox steel

ELECTRICAL CHARACTERISTICS

Nominal power (W) 300 300

Voltage (V) 230 V ~ 230 V ~

Current (A) 1.3 1.3

Class II

 

SAFETY & INSTALLATION

Installation kit included

 

Safety thermostat

 

Protection grade IP 44 IP 44

2. Rointe towel rails installation

2.1. Mounting instructions

Inside the packaging you will nd a xing kit. Please nd the instructions below:

Inside the box/packaging you will nd a mounting kit:

1. Choose the right part of the wall.

2. Place the mounting stencil on the wall, marking the places for the holes.

3. Remove the stencil and make the holes in the wall.

4. Insert the rawl plugs in the holes made.

5. Screw the four metallic fasteners to the wall with the 6.3 x 50 mm screw.

6. Screw the four metallic cylinders to the product (see Figure 1).

7. Insert what you have assembled in Section 6 into the metallic fastener and x well with the 2.9

x 9.5 mm stud bolt.

NO. ELEMENT

1 10 mm Rawl Plug

2 Metallic fastener

3 Screw 2.9 x 9.5mm

4 Screw 6.3 x 50mm

5 Product

2.2. Connecting instructions

Connection to the mains must be made observing the voltage stated on the product technical data label.

This product is designed to be permanently installed connected to xed facilities. The product power

supply circuit must have an all-pole circuit breaker switch with a separation of at least 3 mm between

the contacts.

The product must be installed, if possible, away from any source of draughts (windows, doors) or any

other thing which may affect its functioning. In this way, the temperature will not be affected. Place any

object which might prevent the air ow (furniture, armchairs) 50 cm away from the front of the product.

The product must never be installed immediately below a power point. The lower part of the control

panel must be placed at least 15 cm from the oor.

For any product, if the power cable is damaged, it must be replaced by a specic cable. The replacement

of the cable must be done by the Rointe after-sales service or qualied personnel. The technical

specications of your product appear on the technical data label.

CIRCE OVAL

IMPORTANT - This product must never be installed with its control

panel at the top. This product must not be installed horizontally. During

installation, use wedges so that the control panel will not be in contact

with the ﬂoor.

2.3. Speciﬁc Regulations for Bathrooms

This product can be safety installed in Zones 3. For installations in Zones 2 (check the scheme below),

please consider the following limitations:

•

In bathrooms, the product must never be installed in such a way that the control panel may be touched

by someone in the bathtub or having a shower. The control panel should be located at least 600 mm

distance from any wet areas. The body of the product can be placed in Zones 2 if the control panel is

located inside Zone 3.

• In a kitchen or bathroom, the body of the product must be placed at least 25 cm from the oor.

3. Control panel description and functions

3.1. Control panel

The control panel is made up of 7 LEDs and 4 mechanical buttons with the following functionalities:

Power / Stand-by / Conrmation button

Increase temperature button

Decrease temperature button

Maximum power button

Infrared sensor

1 2 3 4 5 6

3.2. Power and Stand-by

To turn on the product, press the button once. To turn off the product, press the button again.

3.3. Set temperature selection

You can regulate the set temperature of the towel rail by the buttons and . Pressing the

key increases the setpoint temperature. In the same way, pressing the key reduces the setpoint

temperature.

The minimum operating temperature is 7ºC and the maximum is 30ºC. The factory set temperature

is 21ºC. The 6 LED indicators, located in the upper part of the control panel, identify the established

setpoint temperature.

Iindicator LED Temperature Iindicator LED Temperature

1 LED

Led 1: short

blink every 2

seconds

Led 2: OFF

Led 3: OFF

Led 4: OFF

Led 5: OFF

Led 6: OFF

7ºC

1 LED

Led 1: ON

Led 2: OFF

Led 3: OFF

Led 4: OFF

Led 5: OFF

Led 6: OFF

15ºC

CIRCE OVAL

Iindicator LED Temperature Iindicator LED Temperature

2 LED

Led 1: ON

Led 2: ON

Led 3: OFF

Led 4: OFF

Led 5: OFF

Led 6: OFF

18ºC

3 LED

Led 1: ON

Led 2: ON

Led 3: ON

Led 4: OFF

Led 5: OFF

Led 6: OFF

21ºC

4 LED

Led 1: ON

Led 2: ON

Led 3: ON

Led 4: ON

Led 5: OFF

Led 6: OFF

24ºC

5 LED

Led 1: ON

Led 2: ON

Led 3: ON

Led 4: ON

Led 5: ON

Led 6: OFF

27ºC

6 LED

Led 1: ON

Led 2: ON

Led 3: ON

Led 4: ON

Led 5: ON

Led 6: ON

30ºC

3.4. Consumption identiﬁcation

The last temperature indicator LED will ash to indicate the heating element is active and the product

is consuming energy.

3.5. Keypad lock

By pressing the and keys together for 3 seconds, you can lock/unlock the control panel keypad.

If any key is pressed while the panel is locked, all the LEDs will ash twice.

For safety reasons, the on/off button

will respond even if the panel is locked. To switch the

product on or off when the panel locked, press and hold the button for 3 seconds.

3.6. MAX POWER mode

The MAX POWER mode activates the towel rail heating element to maximum power continuously

regardless of the sensor reading. To activate this function from the control panel, press the button

. You can also activate this mode, even when the product is switched off.

Pressing

once will activate this mode for 15 minutes. If you press (X) again within the next two

seconds, the next period (30 minutes) will be activated. Consecutive presses will activate the

following periods as shown in the table below:

Iindicator LED Time Iindicator LED Time

1 LED

Led 1: ashing

Led 2: OFF

Led 3: OFF

Led 4: OFF

Led 5: OFF

Led 6: OFF

Led 7: ON

minutes

2 LED

Led 1: ashing

Led 2: ashing

Led 3: OFF

Led 4: OFF

Led 5: OFF

Led 6: OFF

Led 7: ON

minutes

3 LED

Led 1: ashing

Led 2: ashing

Led 3: ashing

Led 4: OFF

Led 5: OFF

Led 6: OFF

Led 7: ON

minutes

4 LED

Led 1: ashing

Led 2: ashing

Led 3: ashing

Led 4: ashing

Led 5: OFF

Led 6: OFF

Led 7: ON

minutes

5 LED

Led 1: ashing

Led 2: ashing

Led 3: ashing

Led 4: ashing

Led 5: ashing

Led 6: OFF

Led 7: ON

minutes

6 LED

Led 1: ashing

Led 2: ashing

Led 3: ashing

Led 4: ashing

Led 5: ashing

Led 6: ashing

Led 7: ON

120

minutes

If you press the button 7 times, you will return to the starting point (activation for 15 minutes).

The LEDs will work as a countdown, turning off as the time elapses. Once the time has elapsed, the

product will automatically return to the previous mode or will switch off if it was already in stand-by.

The MAX POWER mode can be stopped at any time by a short press on the button

. The towel rail

will return to its previous state.

3.7. Remote control

(optional)

The towel rails with the OVAL control panel can be controlled using the Rointe AIR and BASIC Control

remotes (sold separately). The use of the remote control extends the functionality of the towel rail by

allowing:

CIRCE OVAL

• Complete control without the need to use the control panel.

• More accurate setpoint temperatures to be set (half a degree by half a degree between 15 and

30 ºC e.g. 19.5 ºC).

• 24 hours a day, 7 days a week personalised programming or by using one of the 4 pre-installed

programmes on the BASIC Control remote.

To learn more about Rointe remote controls and their functions, go to our web portal or consult their

user manual.

IMPORTANT: When the product is programmed using a Rointe remote control, LED

number 7 (corresponding to MAX POWER mode) will ash.

WARNING: If the towel rail is automatically programmed and you wish to use it again

in manual mode, you must hold down the on/off button for 3 seconds (with the product

unlocked). The product will no longer be programmed and you will be able to control it

manually using the buttons on the control panel.

3.8. Troubleshooting

During normal operation of the towel rail, any malfunctions can be indicated by the LED indicators on

the product. See table below to identify the error codes:

Indicator Code Error Solution

LED 6

ashing

Led 1: OFF

Led 2: OFF

Led 3: OFF

Led 4: OFF

Led 5: OFF

Led 6: ashing

Led 7: OFF

Temperature sensor

failure due to short-

circuit or open sensor.

Please contact the

Rointe Technical Support

department by calling our

support team.

4. Maintenance & Cleaning

The product does not require any type of maintenance. We recommend that all parts of the product

are kept clean (behind, underneath, upper ns, etc.). Do not use any abrasive product on the steel

main body. Clean it with a damp cloth and a pH neutral soap, and the control panel with a dry cloth.

European Directive 2012/19/UE

Under the European Directive 2012/19/UE on waste electrical and electronic equipment (WEEE), the

product cannot be disposed in the usual council bins and containers. They must be separated to

optimize the recovery and recycling of all of the components and materials and reducing the impact

to human health and the environment. The symbol of the container crossed out over a horizontal line

is marked on all of Rointe products to remind the consumer of the obligation to separate them on

disposal.

The consumer should contact the local authority or original point of sale to learn more about the

correct disposal of this product.

5. Guarantee

In this section, we hereby describe the guarantee conditions which the buyer acquires on buying a

new Rointe product. These conditions comply with all the rights construed in the national legislation

in force, as well as any additional rights and guarantees which are offered by Rointe.

5.1. Any incident that you might detect in your Rointe product can be sorted by the product seller or

quickly by the manufacturer. Please contact Rointe by telephoning (UK) 0203 321 5929 or (Ireland)

01 553 0523 for technical support. If you live in a different country, please check the correct phone

number on the back of this manual.

CIRCE 500 300W

TCIVN45B077

300 W

You will need to state the product reference (located on the label indicating product features), serial

number, proof of purchase and the type of incident at hand when contacting us so that we can check

the guarantee. In addition, please attach a copy of the product invoice.

5.2. Rointe guarantees that there are no material defects of design or manufacture at the time of

original acquisition and guarantees the steel main body for a period of 120 months and 24 months for

any electronic and electrical components.

5.3. If during the guarantee period, the product does not work correctly under normal use, and any

design, material or manufacturing defect is found, Rointe will repair or substitute the product as it

may see t, in accordance with the terms and conditions as follows:

5.3.1. The guarantee is only applicable if the original guarantee is issued by the seller and when

the said guarantee is lled in correctly including product reference, series number (marked on the

product’s label indicating technical features), purchase date and the seller’s stamp.

Rointe reserves the right to reject the guarantee service when this information has been removed or

modied after the original product purchase.

CIRCE OVAL

5.3.2. The guarantee only applies to those cases that concern material, design and manufacturing

defects, and under no circumstances covers damage to the product for the following reasons:

5.3.2.1 Incorrect use of the product, i.e. used for other purposes that are not construed as its

normal use or for not respecting the instructions of use and maintenance given by Rointe as well as

incorrect installation or use of the product that may not comply with the current technical standards

of safety.

Corrosion caused by direct exposure to salt water is excluded from the guarantee. When the product

is installed no more than 200m from the coast the guarantee for damages caused by corrosion the

period will be reduced by 50%.

5.3.2.2 Any unauthorized repairs carried out by unauthorized technicians or opening of the

product by unauthorized people.

5.3.2.3 Any accidents that are deemed outside the control of Rointe, such as lightning, res,

oods, public disorders, etc.

5.3.3. Any repairs or substitutions that are included in this guarantee do not allow any additions

or new periods of guarantee.

5.3.4. Any repairs or substitutions covered under this guarantee must be parts that are functional-

ly equivalent. The defective parts or parts removed or replaced shall become the property of Rointe.

5.4. The technical service of Rointe will advise you if you need to buy any parts not covered under

the guarantee or out of guarantee.

5.5. This guarantee does not affect the buyer’s legal rights stipulated in the current national legisla-

tion, nor affects those rights against the distributor or installer that could come forth in compliance

with the purchase contract.

5.6. In the absence of a national legal legislation applicable, this guarantee shall prevail and may be

construed as the buyer’s only protection. Rointe, its ofces, distributors and installers may not be

held responsible for any accidental damage that emerges due to infringement of any rules implicitly

related to this product.

6. How to register your product guarantee

IMPORTANT: It’s important to register your ROINTE product as part of our guarantee service, in

case you wish to make a claim.

You can register your ROINTE product in the following ways:

WEBSITE

1. Go to www.rointe.com/uk/register-your-guarantee/.

2. Login to your existing account or create a new account if you need to.

3. Click on “My products”.

4. Enter your product reference (alphanumeric and in upper case).

5. Enter your serial number (26 digits located on the metal tag on your product and starts with 843).

6. Upload your proof of purchase, such as invoice in PDF, JPEG or PNG format. This is not

mandatory but by doing so you ensure your guarantee period is accurate.

7. Click “Register”.

8. Congratulations! Your product is now registered.

1. Send an email to [email protected] with the following information:

• Customer name

• Address and postcode

• Telephone number and email address

• Product reference (as described above)

• Serial number (as described above)

• Product purchase date and proof of purchase (as described above).

2. Our Technical Support team will conrm your product registration and request any additional

information needed via email.

POST

1. Post the information listed in the EMAIL section above to:

• INDUSTRIAS ROYAL TERMIC, S.L. t/a Rointe UK, C/E Parcela 43, 30140,

Santomera (SPAIN)

2. Please ensure you obtain proof of posting.

CIRCE OVAL

7. ERP DIRECTIVE (EU) 2015/1188

ITEM SYMBOL UNIT

TCIV*48A080

TCIV*53A080

TCIV*48A120

TCIV*53A120

HEAT OUTPUT

Nominal heat output

nom kW 0.30 0.30

Minimal heat output

min kW n/a n/a

Maximum continuous heat output

max,c kW 0.30 0.30

AUXILIARY ELECTRICITY CONSUMPTION

At nominal heat output

MAX kW 0.30 0.30

At minimum heat output

MIN kW 0.30 0.30

In standby mode

SB kW 0.002 0.002

CIRCE OVAL

TYPE OF HEAT OUTPUT/ROOM TEMPERATURE CONTROL (SELECT ONE)

Single-level heat output, no internal temperature control — — — —

Two or more manual levels, without internal temperature control — — — —

Internal temperature control by mechanical thermostat — — — —

With electronic interior temperature control — — — —

Electronic indoor temperature control and daily timer — — — —

Electronic indoor temperature control and weekly timer — —

OTHER CONTROL OPTIONS (MULTIPLE SELECTIONS POSSIBLE)

Interior temperature control with presence detection — — — —

Interior temperature control with detection of open windows — —

With remote control / distance option — —

With adaptive start-up control — —

With operating time limitation — —

With black lamp sensor — — —

SEASONAL SPACE HEATING ENERGY EFFICIENCY

s — 39.0% 39.0%

Precauciones de instalación y de seguridad (EN 60335 Standards)

Antes de encender el producto léase el apartado de “precauciones de instalación y de seguridad”

detenidamente para asegurar el funcionamiento correcto del producto.

Precauciones de instalación

Este producto está diseñado para uso doméstico o residencial. Se recomienda que el producto sea

instalado por un profesional autorizado. Asegúrese de que el producto esté conectado correctamente

a 230V.

ATENCIÓN

Los niños menores de 3 años deben mantenerse fuera del alcance del

aparato a menos que estén continuamente supervisados. Los niños de 3 a

8 años sólo deben encender y apagar el aparato cuando se haya colocado

o instalado en su posición normal de uso y cuando se les haya supervisado

o instruido sobre el uso del aparato de forma segura y comprendan

los peligros que conlleva. Los niños de 3 a 8 años no deben enchufar,

ajustar o limpiar el aparato ni realizar operaciones de mantenimiento. Este

aparato puede ser utilizado por niños a partir de 8 años y por personas

con capacidades físicas, sensoriales o mentales reducidas o con falta de

experiencia y conocimientos, siempre que estén supervisados o hayan

recibido instrucciones sobre el uso del aparato de forma segura y entiendan

los peligros que conlleva. Los niños no deben jugar con el aparato. La

limpieza y el mantenimiento del usuario no deben ser realizados por los

niños sin supervisión. Los niños deben ser supervisados en todo momento

para asegurarse de que no intereren con el producto.

Este producto de calefacción se rellena con una cantidad precisa de aceite

especial que no necesita mantenimiento. Las reparaciones que necesitan

la apertura del depósito de uido térmico no deberán efectuarse más que

por Rointe o su servicio posventa. Las reglamentaciones concernientes

a la eliminación de este uido después de que el aparato calefactor sea

desechado deben ser respetadas. Si el cable de alimentación está dañado,

debe ser reemplazado por el fabricante, su servicio posventa o personal

cualicado para evitar daños.

No corte el cable de alimentación bajo ningún concepto con el n de evitar

riesgos eléctricos y garantizar el correcto funcionamiento del producto.

No encienda el secatoallas si observa algún daño externo al desembalar

o instalar el producto. Si el cable de alimentación está dañado, debe ser

sustituido por el fabricante, su servicio postventa o personal autorizado

para evitar cualquier daño.

CIRCE OVAL

No rocíe ni moje el producto. Durante el funcionamiento, mantenga el

producto alejado de materiales combustibles como cortinas, muebles,

etc. No coloque sobre el producto nada que no sea ropa, toallas o tejidos

no inamables.

El secatoallas debe instalarse de forma que el enchufe esté siempre

accesible. El cable de alimentación nunca debe estar en contacto con el

producto durante su funcionamiento.

PRECAUCIÓN - No toque nunca el producto con las manos u

otra parte del cuerpo mojadas.

PRECAUCIÓN - Algunas partes de este producto podrían

ponerse muy calientes y causar quemaduras. Se debe prestar

atención especial cuando niños y personas vulnerables estén

presentes.

Contenido

1. Especicaciones técnicas de producto.................................................................................................20

2. Instalación del secatoallas Rointe ..........................................................................................................22

2.1. Montaje ...............................................................................................................................................22

2.2. Normas de conexión..............................................................................................................................22

2.3. Reglas particulares para los cuartos de baño..................................................................................23

3. Descripción del panel de control y funcionamiento........................................................................24

3.1. Panel de control....................................................................................................................................24

3.2. Encendido y stand-by.............................................................................................................................24

3.3. Selección de temperatura de consigna.............................................................................................24

3.4. Idicativo de consumo..................................................................................................................24

3.5. Bloqueo de teclado.........................................................................................................................24

3.6. Modo MAX POWER.........................................................................................................................24

3.7. Control mediante mando a distancia..............................................................................................27

3.8. Identicación de errores........................................................................................................................28

4. Mantenimiento y limpieza........... ..........................................................................................................28

5. Garantía............................................. ......................................................................................................28