TP-LINK Archer BE800 BE19000 Tri Band WiFi 7 Router Manuel utilisateur

Marque: TP-LINK

Modèle: Archer BE800 BE19000 Tri Band WiFi 7 Router

Taper: Manuel utilisateur

135

• Use another web browser or computer to log in again.

• Reset the router to factory default settings and try again. If login still fails, please

contact the technical support.

Note: You’ll need to reconfigure the router to surf the internet once the router is reset.

Q4. What should I do if I can’t access the internet even though the

configuration is finished?

1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for

the router.

2. Go to Advanced> Network > Status to check internet status:

If IP Address is a valid one, please try the methods below and try again:

• Your computer might not recognize any DNS server addresses. Please manually

configure the DNS server.

1 ) Go to Advanced > Network > DHCP Server.

2 ) Enter 8.8.8.8 as Primary DNS, click SAVE .

Tips: 8.8.8.8 is a safe and public DNS server operated by Google.

136

• Restart the modem and the router.

1 ) Power off your modem and router, and leave them off for 1 minute.

2 ) Power on your modem first, and wait about 2 minutes until it gets a solid cable

or Internet light.

3 ) Power on the router.

4 ) Wait another 1 or 2 minutes and check the internet access.

• Reset the router to factory default settings and reconfigure the router.

• Upgrade the firmware of the router.

• Check the TCP/IP settings on the particular device if all other devices can get internet

from the router.

As the picture below shows, if the IP Address is 0.0.0.0, please try the methods below

and try again:

• Make sure the physical connection between the router and the modem is proper.

• Clone the MAC address of your computer.

137

1 ) Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set

for the router.

2 ) Go to Internet or Advanced > Network > Internet and focus on the MAC Clone

section.

3 ) Choose an option as needed (enter the MAC address if Use Custom MAC

Address is selected), and click SAVE .

Tips:

• Some ISP will register the MAC address of your computer when you access the internet for the first time

through their Cable modem, if you add a router into your network to share your internet connection, the ISP will

not accept it as the MAC address is changed, so we need to clone your computer’s MAC address to the router.

• The MAC addresses of a computer in wired connection and wireless connection are different.

• Modify the LAN IP address of the router.

Note:

Most TP-Link routers use 192.168.0.1/192.168.1.1 as their default LAN IP address, which may conflict with the IP

range of your existing ADSL modem/router. If so, the router is not able to communicate with your modem and you

can’t access the internet. To resolve this problem, we need to change the LAN IP address of the router to avoid

such conflict, for example, 192.168.2.1.

1 ) Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set

for the router.

2 ) Go to Advanced > Network > LAN.

3 ) Modify the LAN IP address as the follow picture shows. Here we take 192.168.2.1

as an example.

4 ) Click SAVE .

• Restart the modem and the router.

138

1 ) Power off your modem and router, and leave them off for 1 minute.

2 ) Power on your modem first, and wait about 2 minutes until it get a solid cable

or Internet light.

3 ) Power on the router.

4 ) Wait another 1 or 2 minutes and check the internet access.

• Double check the internet connection type.

1 ) Confirm your internet connection type, which can be learned from the ISP.

2 ) Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set

for the router.

3 ) Go to Advanced > Network > Internet.

4 ) Select your Internet Connection Type and fill in other parameters.

5 ) Click SAVE .

6 ) Restart the modem and the router again.

• Please upgrade the firmware of the router.

If you’ve tried every method above but still cannot access the internet, please contact

the technical support.

Q5. What should I do if I can’t find my wireless network or I cannot

connect the wireless network?

If you fail to find any wireless network, please follow the steps below:

• Make sure the wireless function of your device is enabled if you’re using a laptop with

built-in wireless adapter. You can refer to the relevant document or contact the laptop

manufacturer.

139

• Make sure the wireless adapter driver is installed successfully and the wireless

adapter is enabled.

• On Windows 7

1 ) If you see the message No connections are available, it is usually because the

wireless function is disabled or blocked somehow.

2 ) Click Troubleshoot and windows might be able to fix the problem by itself.

• On Windows XP

1 ) If you see the message Windows cannot configure this wireless connection,

this is usually because windows configuration utility is disabled or you are

running another wireless configuration tool to connect the wireless.

2 ) Exit the wireless configuration tool (the TP-Link Utility, for example).

3 ) Select and right click on My Computer on desktop, select Manage to open

Computer Management window.

4 ) Expand Services and Applications > Services, find and locate Wireless Zero

Configuration in the Services list on the right side.

5 ) Right click Wireless Zero Configuration, and then select Properties.

6 ) Change Startup type to Automatic, click on Start button and make sure the

Service status is Started. And then click OK.

If you can find other wireless network except your own, please follow the steps below:

• Check the WLAN LED indicator on your wireless router/modem.

• Make sure your computer/device is still in the range of your router/modem. Move it

closer if it is currently too far away.

• Go to Wireless or Advanced > Wireless > Wireless Settings, and check the wireless

settings. Double check your wireless Network Name and SSID is not hided.

If you can find your wireless network but fail to connect, please follow the steps below:

• Authenticating problem/password mismatch:

1 ) Sometimes you will be asked to type in a PIN number when you connect to

the wireless network for the first time. This PIN number is different from the

Wireless Password/Network Security Key, usually you can only find it on the

label of your router.

140

2 ) If you cannot find the PIN or PIN failed, you may choose Connecting using a

security key instead, and then type in the Wireless Password/Network Security

Key.

3 ) If it continues to show note of Network Security Key Mismatch, it is suggested

to confirm the wireless password of your wireless router.

Note: Wireless Password/Network Security Key is case sensitive.

• Windows unable to connect to XXXX / Can not join this network / Taking longer than

usual to connect to this network:

• Check the wireless signal strength of your network. If it is weak (1~3 bars),

please move the router closer and try again.

• Change the wireless Channel of the router to 1, 6 or 11 to reduce interference

from other networks.

• Re-install or update the driver for your wireless adapter of the computer.

141

FCC compliance information statement

Product Name: BE19000 Tri-Band Wi-Fi 7 Router

Model Number: Archer BE800

Component Name Model

I.T.E. Power Supply T150500-2-DT

Responsible party:

TP-Link USA Corporation

Address: 10 Mauchly, Irvine, CA 92618

Website: http://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6804

E-mail: [email protected]om

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference

that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

142

Note: The manufacturer is not responsible for any radio or TV interference

caused by unauthorized modifications to this equipment. Such modifications

could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment. This device and its antenna must not be co-located

or operating in conjunction with any other antenna or transmitter.

To comply with FCC RF exposure compliance requirements, this grant is

applicable to only Mobile Configurations. The antennas used for this transmitter

must be installed to provide a separation distance of at least 20 cm from all

persons and must not be co-located or operating in conjunction with any other

antenna or transmitter.

FCC regulations restrict operation of this device to indoor use only. The

operation of this device is prohibited on oil platforms, cars, trans, boats, and

aircraft, except that operation of this device is permitted in large aircraft while

flying above 10000 feet. Operation of transmitters in the 5.925-7.125 GHz band

is prohibited for control of or communications with unmanned aircraft systems.

FCC compliance information statement

Product Name: I.T.E. Power Supply

Model Number: T150500-2-DT