Wacker Neuson RT82-SC2 Manuel utilisateur

5200008727 04 0613

Operator’s Manual

Roller

RT 82 SC-2

RTX SC-2

Notice d’Emploi

Rouleau

EN/FR

5200008727

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5200008727 04 0613

RT / RTx Foreword

wc_tx003198gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machines

covered in

this manual

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine Item Number

RT 82 SC-2 0620293

0620367

0620525

0620528

0620529

0620530

0620845

5200003107

RTx 5200008538

5200008539

5200008540

wc_gr009903

Serial Number:

Foreword RT / RTx

4 wc_tx003198gb.fm

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and main-

tain the above Wacker Neuson model(s). For your own safety and to reduce the

risk of injury, carefully read, understand, and observe all instructions described

in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

 The illustrations, parts, and procedures in this manual refer to Wacker Neuson

factory-installed components. Your machine may vary depending on the

requirements of your specific region.

CALIFORNIA

Proposition

65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

RT / RTx Foreword

wc_tx003198gb.fm 5

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker Neu-

son service center according to written instructions published by Wacker Neu-

son.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Foreword RT / RTx

6 wc_tx003198gb.fm

Original Declaration of Conformity

2013-CE-RT_RTx_en.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin USA

Product

Product category

Product function

Item number

Net installed power

Measured sound power level

Guaranteed sound power level

RT 56-SC2, RT 82-SC2, RTx

Trench Roller

To compact soil

0620528, 0620529, 0620530, 0620845, 5200003107,

5200008540

15.5 kW

108 dB(A)

109 dB(A)

Conformity Assessment Procedure

According to ANNEX VIII

Notified Body

Lloyds Register Quality Assurance Limited (Notified Body No 0088)

71 Fenchurch Street, London EC3M 4BS, United Kingdom

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2000/14/EC, 2004/108/EC, EN 500-1, EN 500-4

Authorized Person for Technical Documents

Axel Häret, Wacker Neuson Produktion GmbH & Co. KG, Preußenstraße 41, 80809 München

Menomonee Falls, WI, USA, 22.02.13

William Lahner

Managing Director

Paul Sina

Manager, Product Engineering

Dan Domanski

Technical Director

Table of Contents

RT / RTx

wc_bo5200008726_04TOC.fm

9

Foreword 3

EC Declaration of Conformity 7

1 Safety Information 13

1.1 Signal Words Used in this Manual ..................................................... 13

1.2 Machine Description and Intended Use ............................................. 14

1.3 Safety Guidelines for Operating the Machine ..................................... 15

1.4 Service Safety .................................................................................... 17

1.5 Safety Guidelines for Lifting the Machine ........................................... 18

1.6 Hydraulic Fluid Safety ........................................................................ 19

1.7 Operator Safety while Using Internal Combustion Engines ............... 20

2 Labels 21

2.1 Label Locations .................................................................................. 21

2.2 Label Meanings .................................................................................. 22

3 Lifting and Transporting 29

3.1 Lifting the Machine ............................................................................. 29

3.2 Transporting the Machine ................................................................... 29

4 Operation 31

4.1 Preparing the Machine for First Use ................................................... 31

4.2 Control / Component Locations .......................................................... 32

4.3 Control / Component Descriptions ..................................................... 33

4.4 Features and Controls ........................................................................ 36

4.5 Accessing the Engine or Hydraulic Component Compartments ......... 37

4.6 Accessing the Control Compartment .................................................. 38

4.7 Control Panel ...................................................................................... 39

4.8 SmartControl™ SC-2 Transmitter ...................................................... 41

4.9 Operating Status Indicator Codes ...................................................... 43

4.10 Infra-red System and Control Channels ............................................. 44

4.11 Before Starting ................................................................................... 46

4.12 Starting ............................................................................................... 47

4.13 Stopping ............................................................................................. 48

4.14 Light Ring Color Codes ...................................................................... 49

4.15 Operation ............................................................................................ 50

Table of Contents

RT / RTx

wc_bo5200008726_04TOC.fm

10

4.16 Position of the Operator ......................................................................51

4.17 Range Limits .......................................................................................52

4.18 Operating Characteristics ....................................................................53

4.19 Communication Faults .........................................................................53

4.20 NiMH Battery .......................................................................................54

4.21 Replacing the Battery Pack .................................................................54

4.22 Charging the Transmitter Battery ........................................................55

4.23 Machine Stability .................................................................................56

4.24 Articulated Joint Locking Bar ...............................................................58

4.25 Tip-Overs .............................................................................................58

4.26 Emergency Shutdown Procedure ........................................................59

4.27 Overview of the ECM and the Diagnostic Tool ....................................59

4.28 ECM Stages of Engine Start Up ..........................................................60

4.29 ECM Monitoring of Solenoids ..............................................................61

4.30 Connecting the Diagnostic Tool ..........................................................62

4.31 Programming the ECM Tip-Over Mode ...............................................63

4.32 Entering the ECM Diagnostic Mode ....................................................64

4.33 ECM Fault and Error Codes ................................................................65

4.34 Resetting the ECM Diagnostic Data and the Tip-Over Light ...............67

4.35 Calibrating the Joysticks ......................................................................68

5 Changing Drums (RTx) 70

5.1 Removing the Drum Extensions ..........................................................70

5.2 Installing Drum Extensions ..................................................................72

6 Maintenance 75

6.1 Break-in Period ....................................................................................75

6.2 Periodic Maintenance Schedule ..........................................................75

6.3 Hydraulic Oil Requirements .................................................................76

6.4 Hydraulic Oil Level ..............................................................................77

6.5 Changing Hydraulic Oil and Filter ........................................................77

6.6 Articulated Joint and Steering Cylinders .............................................79

6.7 Cleaning SmartControl™ Transmitter .................................................79

6.8 Scraper Bars .......................................................................................80

6.9 Shock Mounts ......................................................................................81

6.10 Battery .................................................................................................81

6.11

Engine Oil and Filter

................ ....................................................................82

6.12

Lubrication ...........

.................................. ...............................................82

6.13 Servicing the Air Cleaner .....................................................................83

6.14 Engine Fuel Delivery System Maintenance .........................................85

Table of Contents

RT / RTx

wc_bo5200008726_04TOC.fm

11

6.15 Maintaining the Fuel Filter .................................................................. 85

6.16 Draining the Fuel Filter Water Separator ............................................ 86

6.17 Priming the Fuel System .................................................................... 86

6.18 Engine Coolant ................................................................................... 86

6.19 Adjusting Valve Clearance ................................................................. 87

6.20 Adjusting the Fan Belt ........................................................................ 88

6.21 Storage ............................................................................................... 89

6.22 Long-Term Storage ............................................................................ 89

6.23 Machine Disposal / Decommissioning ................................................ 90

7 Troubleshooting 91

8 Technical Data 94

8.1 Engine ................................................................................................ 94

8.2 Roller .................................................................................................. 95

8.3 Lubrication .......................................................................................... 95

8.4 Sound and Vibration Specifications .................................................... 96

8.5 Dimensions ......................................................................................... 96

8.6 Radiation Compliance ........................................................................ 96

9 AEM Safety Manual 97

10 Schematics 124

10.1 Electrical Schematic - Sheet 1 ......................................................... 124

10.2 Electrical Schematic - Sheet 2 ......................................................... 125

10.3 Components ..................................................................................... 126

10.4 Hydraulic Schematic ......................................................................... 130

10.5 Hydraulic Schematic Components ................................................... 131

Table of Contents

RT / RTx

wc_bo5200008726_04TOC.fm

12

wc_si000730gb.fm

13

RT / RTx Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000730gb.fm

14

Safety Information RT / RTx

1.2 Machine Description and Intended Use

This machine is a remote-controlled trench roller. The Wacker Neuson Trench

Roller consists of two distinct machine halves (front and rear) joined by an

articulated joint. Each machine half includes an exciter assembly and two drums.

The front half also includes a diesel engine and pumps for the hydraulic system.

The rear half includes the hydraulic oil reservoir and the fuel tank. The diesel

engine powers the hydraulic systems that provide machine movement and drum

vibration. The operator controls all machine functions (steering, vibration, and

engine start/stop) using an infra-red control system.

This machine is intended to be used for compacting sub-bases, backfill, and

cohesive type soils.

This machine has been designed and built strictly for the intended use(s) described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

 Using the machine as a ladder, support, or work surface

 Using the machine to carry or transport passengers or equipment

 Using the machine to tow other machines

 Operating the machine outside of factory specifications

 Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

 Heat, noise, exhaust, and carbon monoxide from the engine

 Burns from hot hydraulic fluid

 Fire hazards from improper refueling techniques

 Fuel and its fumes

 Personal injury from improper lifting techniques

 Crushing hazards from improper operation and for other persons in the work

zone

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

wc_si000730gb.fm

15

RT / RTx Safety Information

1.3 Safety Guidelines for Operating the Machine

Operator

training

Before operating the machine:

 Read and understand the operating instructions contained in all manuals

delivered with the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Contact Wacker Neuson for additional training if necessary.

When operating this machine:

 Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

 have received instruction on how to properly use the machine

 are familiar with required safety devices

The machine must not be accessed or operated by:

 children

 people impaired by alcohol or drugs

Application

area

Be aware of the application area.

 Keep unauthorized personnel, children, and pets away from the machine.

 Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

Be aware of the application area.

 Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

 Always use the SmartControl™ transmitter neck strap provided by Wacker

Neuson while operating with the control cable connected. This neck strap is

designed to break away so that the operator will not be dragged by the machine

should the machine slide, tip, or fall.

 Always remain in visual contact with the machine at all times while operating the

controls.

 Never operate multiple rollers within 20 meters (65 feet) of one another, unless

you are certain that each roller and its accompanying transmitter have been set

to a different control channel than the other rollers/transmitters being used

within the area. Refer to section Setting Control Channels for additional

information.

wc_si000730gb.fm

16

Safety Information RT / RTx

Safety

devices,

controls, and

attachments

Only operate the machine when:

 All safety devices and guards are in place and in working order.

 All controls operate correctly.

 The machine is set up correctly according to the instructions in the Operator’s

Manual.

 The machine is clean.

 The machine’s labels are legible.

To ensure safe operation of the machine:

 Do not operate the machine if any safety devices or guards are missing or

inoperative.

 Do not modify or defeat the safety devices.

 Only use accessories or attachments that are approved by Wacker Neuson.

Safe

operating

practices

When operating this machine:

 Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

When operating this machine:

 Do not operate a machine in need of repair.

 Do not consume the operating fluids used in this machine. Depending on your

machine model, these operating fluids may include water, wetting agents, fuel

(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic fluid,

heat transfer fluid (propylene glycol with additives), battery acid, or grease.

 Use caution when operating near the edges of pits, trenches or platforms.

Check to be sure that the ground surface is stable enough to support the weight

of the machine with the operator and that there is no danger of the roller sliding,

falling, or tipping.

 Position yourself safely when operating machine in reverse or on hills. Leave

enough space between yourself and the machine so you will not be placed in a

hazardous position should the machine slide or tip.

 Do not use a cellphone or send text messages while operating this machine.

 Stay clear of the articulated steering joint and the area between the front and

rear frames.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

After Use

 Stop the engine when the machine is not being operated.

 Close the fuel valve, if equipped, when machine is not being operated.

 Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

 Store the machine in a clean, dry location out of the reach of children.

wc_si000730gb.fm

17

RT / RTx Safety Information

1.4 Service Safety

Service

training

Before servicing or maintaining the machine:

 Read and understand the instructions contained in all manuals delivered with

the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Only trained personnel shall troubleshoot or repair problems occurring with the

machine.

 Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

 Do not allow improperly trained people to service or maintain the machine.

Personnel servicing or maintaining the machine must be familiar with the

associated potential risks and hazards.

Precautions

Follow the precautions below when servicing or maintaining the machine.

 Read and understand the service procedures before performing any service to

the machine.

 All adjustments and repairs must be completed before operating the machine.

Do not operate the machine with a known problem or deficiency.

 All repairs and adjustments shall be completed by a qualified technician.

 Turn off the machine before performing maintenance or making repairs.

 Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

 Reinstall the safety devices and guards after repair and maintenance

procedures are complete.

 Always secure the articulated steering joint using the locking bar before lifting,

jacking, and servicing the machine. The machine halves could swing together

unexpectedly and cause a serious injury.

 Do not remove the radiator cap when the engine is running or hot. The radiator

fluid is hot and under pressure and may cause severe burns!

 Do not remove air cleaner cover, paper element, or precleaner while engine is

running.

 Do not leave SmartControl™ transmitter unattended while servicing machine.

Machine

modifications

When servicing or maintaining the machine:

 Use only accessories/attachments that are approved by Wacker Neuson.

When servicing or maintaining the machine:

 Do not defeat safety devices.

 Do not modify the machine without the express written approval of Wacker

Neuson.

wc_si000730gb.fm

18

Safety Information RT / RTx

Replacing

parts and

labels

 Replace worn or damaged components.

 Replace all missing and hard-to-read labels.

 When replacing electrical components, use components that are identical in

rating and performance to the original components.

 When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

Cleaning

When cleaning and servicing the machine:

 Keep the machine clean and free of debris such as leaves, paper, cartons, etc.

 Keep the labels legible.

When cleaning the machine:

 Do not clean the machine while it is running.

 Never use gasoline or other types of fuels or flammable solvents to clean the

machine. Fumes from fuels and solvents can become explosive.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

1.5 Safety Guidelines for Lifting the Machine

When lifting the machine:

 Make sure slings, chains, hooks, ramps, jacks, forklifts, cranes, hoists, and any

other type of lifting device used is attached securely and has enough weight-

bearing capacity to lift or hold the machine safely. See section Technical Data

for machine weight.

 Remain aware of the location of other people when lifting the machine.

 Only use the lifting points and tie-downs described in the Operator’s Manual.

 Make sure the transporting vehicle has sufficient load capacity and platform size

to safely transport the machine.

To reduce the possibility of injury:

 Do not stand under the machine while it is being lifted or moved.

 Do not get onto the machine while it is being lifted or moved.

wc_si000730gb.fm

19

RT / RTx Safety Information

1.6 Hydraulic Fluid Safety

Safety

instructions

 Inspect the hydraulic system thoroughly before operating the machine.

 Do not touch hydraulic fluid or hydraulic components while the machine is

operating. Wait until the machine is cool.

 Before disconnecting hydraulic fittings or hoses, ensure that all pressure has

been bled from the circuit. Set all controls in neutral, turn engine off, and allow

the fluids to cool before loosening hydraulic fittings or attaching test gauges.

 Hydraulic fluid escaping under high pressure may penetrate the skin, cause

burns, blind, or cause other serious injuries or infections. Contact a physician

immediately for treatment if your skin has been penetrated by hydraulic fluid,

even if the wound seems minor.

 Fluid leaks from small holes are often practically invisible. Do not use your bare

hands to check for leaks. Check for leaks using a piece of cardboard or wood.

 Hydraulic fluid is extremely flammable. Stop the engine immediately if a

hydraulic leak is detected.

 After servicing the hydraulics, make sure all components are reconnected to the

proper fittings. Failure to do so may result in damage to the machine and/or

injury to a person on or near the machine.

WARNING

Possibility of severe injury. Hydraulic fluid is under high pressure and becomes very

hot during operation.

f To avoid injury, obey the safety instructions listed below.

wc_si000730gb.fm

20

Safety Information RT / RTx

1.7 Operator Safety while Using Internal Combustion Engines

Operating

safety

When running the engine:

 Keep the area around exhaust pipe free of flammable materials.

 Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine. Do not run the machine if fuel leaks are present or the fuel lines are

loose.

When running the engine:

 Do not smoke while operating the machine.

 Do not run the engine near sparks or open flames.

 Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

 Do not operate a machine when its fuel cap is loose or missing.

 Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

Refueling

safety

When refueling the engine:

 Clean up any spilled fuel immediately.

 Refill the fuel tank in a well-ventilated area.

 Replace the fuel tank cap after refueling.

 Use suitable tools for refueling (for example, a fuel hose or funnel).

When refueling the engine:

 Do not smoke.

 Do not refuel a hot or running engine.

 Do not refuel the engine near sparks or open flames.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

La page charge ...

Wacker Neuson RT82-SC2 Manuel utilisateur

Ce manuel convient également à

Wacker Neuson RT82-SC2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents