GE JGP330BEKBB - 30" Gas Cooktop Guide d'installation

Marque: GE

Modèle: JGP330BEKBB - 30" Gas Cooktop

Taper: Guide d'installation

Installation

Instructions

36" SealedGasCooktop

JGP628, JGP630, JGP963, JGP9?0,

JGP9?5, ZGU36

I Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca

IN THE COMMONWEALTH OF

MASSACH USETTS:

• This product must be installed by u licensed

plumber or gas fitter.

• When using ball-type gas shut-off valves, they

shall be the T-handle type.

• A flexible gas connector, when used, must not

exceed 3 feet.

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

•IMPORTANT - Savetheseinstructions

forlocalinspector'suse.

•IMPORTANT - Observeallgoverning

codes and ordinances.

• Note to Installer- Be sure to leave these

instructions with the Consumer.

• Note to Consumer - Keep these instructions for

future reference.

• Product failure due to improper installation is not

covered under the Warranty.

-&WARNING - This appliance must be

properly grounded.

• IMPORTANT - Leak testingofthe

applianceshallbe conducted accordingto the

manufacturer'sinstructions.

• Proper installation is the responsibility

of the installer and product failure due to

improper installation is NOT covered under

warranty.

-AWARNING - Disconnectallelectrical

power atthe main circuit breaker

or fuse box before installing.

FOR YOUR SAFETY:

-&WARNING - Iftheinformation

in this manual is not followed exactly, a fire,

explosion or gas leak may result causing property

damage, personal injury or death.

Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance!

WHAT TO DO IF YOU SMELL

GAS:

Do not try to light any appliance. Do not touch

any electrical switch; do not use any phone in

your building.

Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire

department.

Installation and service must be performed by

a qualified installer, service agency or the gas

supplier.

This cooktop has been design certified

by CSA International. You'll find safety precautions

in your Owner's Manual.

Read them carefully.

Installation of this cooktop must conform with

local codes or, in the absence of local codes with

the National Fuel Gas Code, ANSI Z223.1/NFPA

54-Latest edition.

Be sure your cooktop is installed properly by a

qualified installer or service technician.

To eliminate reaching over surface burners,

cabinet storage above burner should be avoided.

Do not install the unit near an outside door or

where a draft may affect its use.

31-i0612-4 (lO-lO GE) 1

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

ELECTRICAL REQUIREMENTS

This appliance must be supplied with the proper

voltage and frequency and connected to an

individual, properly grounded branch circuit,

protected by a circuit breaker or fuse having

amperage as noted on the rating plate.

We recommend you have the electrical wiring and

hookup of your cooktop connected by a qualified

electrician. After installation, have the electrician

show you where your main cooktop disconnect is

located.

Check with your local utilities for electrical codes

which apply in your area. Failure to wire your

cooktop according to governing codes could result

in a hazardous condition.

If there are no codes, your cooktop must be wired

and fused to meet the requirements of the National

Electrical Code, ANSl/NFPA No. 70--Latest edition.

You can get a copy by writing:

National Fire Protection Association

Batterymarch Park

Quincy, IVlA 02269

In Canada your cooktop must be wired and fused

to meet the requirements of the Canadian Electrical

Code.

Be sure the installation of this product in a mobile

home conforms with the Manufactured Home

Construction and

Safety Standard, Title 24 CFR, Part 3280.

If this standard does not apply, you must follow

the standard for Manufactured Home Installations,

ANSI A225.1 and Manufactured Home Installations,

Sites and Communities and ANSI/NFPA S01A or

with local codes.

You can get a copy of the Federal Standard by

Writing:

Office of Mobile Home Standards

HUD Building

451 7th Street, S.W.

Washington, D.C. 24010

PARTS INCLUDED

2 Screws

Foam Tape

(GlassTop

Models Only)

2 Hold

Down Brackets

MATERIALS YOU MAY NEED

Joint Sealant Pipe Fittings

Shut-Off Valve

CSA-Approved Flexible Gas Line

3/8" Min. ID, 1/2" NPTConnection,

3-foot Maximum Length (Massachusetts Only)

TOOLS YOU WILL NEED

FOR INSTALLATION

I IIf_( ( _ /,(---]/ ]]

Pencil

Saber Saw

Phillips-Head

Screwdriver

Ruler or Straightedge

Safety Glasses

Pipe Wrench

1/8" Drill Bit & Electric or

Hand Drill

Installation Instructions

PRE-INSTALLATION CHECKLIST

When preparing cooktop opening, make

sure the inside of the cabinet and the

cooktop do not interfere with each other.

(See section on preparing the opening.)

Remove packaging materials, grate boxes,

regulator with literature, and literature

package from the cooktop before beginning

installation.

Package

Grate boxes

Foam_ _

Pac _ [_3_ i] _j

Cool<top J

r61

[]

FF1

Remove Installation Instructions from

literature pack and read them carefully

before you begin.

Be sure to place all literature, Use and Care,

Installations, etc. in a safe place

for future reference.

Make sure you have all the tools and

materials you need before starting the

installation of the cooktop.

Your home must provide the adequate

electrical service needed to safely and

properly use your cooktop. (Refer to section

on electrical requirements.)

When installing your cooktop in your home,

make sure all local codes and ordinances

are followed exactly as stated.

Make sure the wall coverings, countertop

and cabinets around the cooktop can

withstand heat (up to 200°F) generated by

the cooktop.

Instollotion Instructions

PREPARING THE OPENING

MAINTAIN THE FOLLOWING

MINIMUM CLEARANCE

DIMENSIONS

13" MAX.Depth of unprotected

overhead cabinets

\\ 6" MIN. clearance from

cutout to side wall on the

right of the unit

30" MIN. clearance from countertop

to unprotected overhead surface

18" MIN. height

from countertop to

nearest cabinet on

either side of unit

3-3/4" MIN.clearance from

cutout to side wall on the

left of the unit

NOTE:All gas cooktop models require 7/16"

free area below cooktop height to combustible

material.

I_l OVERALL COOKTOP DIMENSIONS

21" (21-1/4" IVlax.for

CUTOUT DIMENSIONS OF

COUNTERTOP

To ensure accuracy, it is best to make

a template when cutting the opening

in the counter.

_-1/8 _"width cut

length _ 16-15/16"

2-1/4" Min. B of cutcutout and the wail

behind the cooktop

2-1/2" Min. from

front edge of cutout

and front edge of

countertop

RECOMMENDED GAS SUPPLY

LOCATION FROM BACKWALL

Recommended

gas supply

location

l" Min. From Backwall

From Cutout

Center Line

F51 MAKE SURE WALL COVERINGS,

COUNTERTOP AND CABINETS

AROUND COOKTOP CAN

WITHSTAND HEAT {UP TO 200°F)

GENERATED BY COOKTOP

Wall covering,

cabinets and

countertop must

withstand heat

up to 200°F

Installation Instructions

INSTALLING THE COOKTOP UNIT

LOCATE ELECTRICAL OUTLET AND

GAS SHUT-OFF VALVE BENEATH

CABINET

NEVER REUSEOLD

CONNECTORS WHEN

INSTALLING THIS

UNIT.

H I

J_J

shutoff11i\

_L Valve r_ I Electrical

II Outlet 12"

I Below

Countertop

Install a manual shut-off valve in the gas line in an

easily accessible location outside the cooktop. Be

sure you know how and where to shut off the gas

supply to the cooktop. Install the electrical outlet

12" below the countertop.

_-I PROTECT SURFACE OF COOKTOP

Place a towel or tablecloth onto the

countertop. Lay the cooktop upside down onto the

protected surface.

Bottom of cooktop

Cloth under Cooktop

[_] ATTACH FOAM TAPE

(glass maintop models only)

Apply the foam tape around the outer edge

of the glass. Do not overlap the foam tapes.

Bottom of Cooktop

\ Foam Topes

Cooktop Gloss

LOCATE MOUNTING PARTS

Remove the hold down brackets from the

literature package.

_-I ATTACH BRACKETS TO COOKTOP

Remove the screw from the bottom of the

cooktop and screw the hold-down bracket

to the side of the cooktop unit. Repeat for opposite

side of cooktop.

Pre-drilled

Bottom

of Cooktop

.\.._ Foem Topes

Cooktop

Gloss

I-_ INSERT COOKTOP INTO CUTOUT

Insert the cooktop centered into the cutout

opening. Make sure the front edge of the countertop

is parallel to the cooktop. Make final check that all

required clearances are met.

Once the unit is in place, screw the hold- down

bracket into the cabinet sides to secure the unit

into place.

Installation Instructions

INSTALLATION--GAS CONNECTIONS

PROVIDE ADEQUATE

GAS SUPPLY

This cooktop is designed to operate on natural gas

at 4" of water column manifold pressure and 7" of

water column (W.C.) supply pressure. It is shipped

from the factory set for natural gas. The convertible

pressure regulator supplied with the unit must

be connected in series with the manifold of the

cooktop and must remain in series with the supply

line regardless of whether natural or L.P.gas is

being used.

FOR PROPEROPERATION, THE MAXIMUM INLET

PRESSURETO THE REGULATOR MUST BE NO MORE

THAN 14" OF WATER COLUMN PRESSURE.For

checking the regulator, the inlet pressure must

be at least 1" W.C.. (or 3.4 KPA) greater than the

regulator output setting. If the regulator is set for 4"

W.C. of water column pressure, the inlet pressure

must be at least 5" W.C. If the regulator is set for

10" W.C., the inlet pressure must be at least 11"

W.C.. The gas supply line to the cooktop should be

1/2" or 3/4" pipe.

_-I INSTALL REGULATOR

NEVER REUSEOLD CONNECTORS WHEN

INSTALLING THIS COOKTOP.

-A WARNING: Neverreuseold

flexible connectors. The use of old flexible

connectors can cause gas leaks and personal

injury. Always use new flexible connectors when

installing u gas appliance.

Screw a section of pipe onto

the inlet end of the pressure

regulator and install the

coupling.

Pressure _l

Regulator

Coupling _

To reduce the likelihood of gas leaks, apply teflon

tape or a thread compound approved for use with

LP or Natural gases to all threaded connections.

INSTALL REGULATOR ONTO

BURNER BOX BOTTOM

Screw the regulator

onto

the burner box

bottom pipe

connection.

Make sure the

top of the regulator

facing towards the

cabinet front, easily

accessible through

the cabinet doors.

Pressure __._

Regulator

Coupling --I

Shut-Off

Valve

II Electrical

I Outlet 12"

I Below

Countertop

COMPLETE CONNECTION WITH A

COUPLING

Complete the

connection between

the regulator pipe

coupling and

the shut-off valve.

Pressure

Regulator

Coupling --_

Shut-Off _:

Valve --'_

II Electrical

I Outlet 12"

I Below

Countertop

Installation Instructions

CHECK FOR LEAKS

Before testing for leaks, make sure oll burner knobs

ore in the OFF position.

After connecting the cooktop to gas, check system

for leaks with o manometer. If a manometer is not

available, turn the gas supply on to the cooktop

and use o liquid leak detector at oil joints and

connections to check for leaks.

Tighten oil connections if necessary to prevent gas

leakage in the cooktop or supply line.

DO NOT USE OPEN FLAME TO CHECK FOR

LEAKS!

Disconnect the cooktop and its individual shut-off

valve from the gas supply piping system during any

pressure testing of that system at test pressures

greater than 1/2 psig (3.5 kPa).

Isolate the cooktop from the gas supply piping

system by closing its individual shut-off valve

during any pressure testing of the gas supply

system at test pressures equal to or less than

1/2 psig (3.5 kPa).

INSTALLATION OVER

BUILT-IN OVEN

See built-in oven installation for complete

installation instructions.

I _ s,,ToCenterof

| I _] 2" Dia. Hole From

_ _ Countertop

90 ° Elbow ........ I ---'_--

7 _1"_ 2"Dia.Hole

(20 7/8" from front

of Countertop to

Hole Center}

Cabinet Sides

Installation Instructions

INSTALLATION--ELECTRICAL CONNECTIONS

_AWARNING - Disconnectoilelectricol

power ot the moin circuit breoker or fuse box

before instolling.

EXTENSION CORDS

Because of potential safety hazords under certoin

conditions, we strongly recommend against the

use of an extension cord. However, if you still

elect to use an extension cord, it is absolutely

necessary that it be a UL listed B-wire grounding

type applionce extension cord ond thot the

current carrying rating of the cord in amperes be

equivalent to or greoter than the branch circuit

roting. Such extension cords ore obtoinoble

through your Iocol opplionce deoler.

IMPORTANT: (Pleosereod corefully)FOR

PERSONAL SAFETY,THIS APPLIANCE MUST BE

PROPERLY GROUNDED.

ELECTRICAL SUPPLY AND OUTLET

An odequote electricol supply ond outlet must

be used to operote the electricol ports of your

cooktop.

The power cord of this applionce is equipped

with o 3-prong (grounding) plug which must

be used with o properly grounded 3-hole

outlet with u standard 120 Volt, 60 cycle AC

household current.

If you do not hove o 3-hole grounded outlet,

hove o quolified electricion chonge your old

one.

A grounding odoptor will be needed

to convert the old one until the outlet

con be reploced. This method is only

temporary, ond o qualified electrician should

test it to be sure it meets requirements.

Ensure proper

L groundond

firmconnection

beforeuse

TWO-PRONG WALL RECEPTACLE

Where a standard 2-prong wall receptacle is

encountered, it is the personal responsibility and

obligation of the customer to hove it replaced with

u properly grounded B-prong wall receptacle.

Do not under any circumstonces cut or remove

grounding prong from the cooktop cord. Failure

to provide proper polarization may create u

hazardous condition.

Installation Instructions

USAGE SITUATIONS WHERE

APPLIANCE POWER CORD

WILL BE DISCONNECTED

INFREQUENTLY

For 15 amp circuit only. Do not use an adaptor

on a 20 amp circuit. Where local codes permit, a

TEMPORARY CONNECTION may be made to a properly

grounded two-prong wall receptacle by the use of a

UL-listed adaptor available at most hardware stores.

The larger slot in the adaptor must be aligned with

the large slot in the wall receptacle to provide proper

polarity in the connection of the power cord.

Ensure proper ground and firm

_. connection before use

Alignlarge

prongs/slots

Temporary Method

(Adaptor plugs not permitted in Canada)

-ACAUTION: Attachingthe adaptor ground

terminaltothe wallreceptaclecoverscrew does not

ground the applianceunlessthe screw ismetal,and

notinsulated,and the wallreceptacleisgrounded

through the house wiring.The customer should have

the circuitchecked by a qualifiedelectriciantomake

surethe receptacleisproperlygrounded.

When disconnecting the power cord from the

adaptor, always hold the adaptor with one hand. If

this is not done, the adaptor ground terminal is very

likely to break with repeated use. Should this happen,

DO NOT USE the appliance until a proper ground has

again been established.

Usage situation where appliance power cord will be

disconnected frequently.

Do not use an adaptor plug in these situations

because disconnection of the power cord places

undue strain on the adaptor and leads to eventual

failure of the adaptor ground terminal. The customer

should have the 2-prong receptacle replaced with

a 3-prong (grounding) receptacle by a qualified

electrician before using the appliance.

Installation Instructions

COOKTOP BURNERS

ASSEMBLING THE COOKTOP

BURNERS

The electrode of the spark igniter is exposed. Be

careful not to push any cooktop controls while the

top of the burner is removed.

Do not remove the top or touch the electrode

of any burner while another burner is turned on.

Electrical shock might result.

Reploce the burner head onto the burner

bose, making sure that the heod is properly

oriented over the burner bose ond the

electrode. Moke sure to place

the correct burner head on the correct burner

bose and thor the burner head sits level on

the burner bose. The burner heads ore not

interchongeoble.

[]

Place the burner

cops on the burner

heads, making sure

to place the correct

burner cop on the

correct burner

head. The burner

cops ore not

interchangeable.

Make sure that the

burner cops ore

properly seated on

the burner heads.

Burner cop properly seoted

Burner cop not properly seoted

[]

Make sure the pins in

the burner heads

match the burner

bose indentutions

und that they ore

properly seated in

them by rotating the

heuds until they ore

level.

Make sure the slot in

the burner head

is positioned

over the

electrode. The

burner cup has

three to four

pins. When

replucing the

cup, make

sure none of

the pins sits

in the stability

chamber.

Burner cop

Burner heod

_ectrode

__Burner

Pin base

indentations

Stabilit_

chamber _

Electrode

Burnerbase

Make sure the hole Burner cop

in the burner head

assembly ispositioned

over the electrode and Burner head

that the burner heod is ossembly_r_-_]b,

fully inserted inside the

burner bose. A small

gop between the bose

and head is normal.

Electrode Burner

bose

Installation Instructions

[_ CHECK IGNITERS

Operation of the electric igniters should be

checked after the cooktop and supply line have

been carefully checked for leaks and the cooktop

has been connected to the electrical power.

On models so equipped, check to be sure the

cooktop is in the UNLOCKED position.

r_ Push and turn a burner valve to the LITE

position. All spark igniters will make a series of

sparks (ticking sounds), but only the burner

turned to LITE will light.

• The burner should light when gas is

available to the burner.

• Once the burner lights, it should be turned

out of the LITE position.

r_ Try each valve separately until all burners

have been checked.

_-I BURNER IGNITION

Cooktop Spark Ignition-When you turn the

cooktop knob to LITE,the spark igniter makes u

series of electric sparks (ticking sounds) which light

the burner. During a power failure, the burners will

not light automatically. In an emergency, a cooktop

burner may be lit with a match by following the

steps below.

-&WARNING: Lighting gas burners with a

match is dangerous. You should match light the

cooktop burners only in an emergency.

On models so equipped, check to be sure the

cooktop is in the UNLOCKED position.

r-_ Light a match and hold the flame near the

burner you want to light. Wooden matches

work best.

r_ Push in and turn the control knob slowly. Be

sure you are turning the correct knob for the

burner you are lighting.

NOTE: If the burner does not light within five seconds,

turn the knob off and wait one minute before trying

again.

THE BURNER FLAMES

Turn each burner on. Flames should be blue in color

with no trace of yellow. The burner flames should

not flutter or blow away from the burner. The flame

should be no less than 1/4" on the lowest setting

and no greater than 1-1/2" on highest setting.

-&WARNING: ,fyouattempt to measure

the flame, please use caution.

Burns could result.

Cooktop Burner

Burners should be checked frequently

I-_ BURNER GRATES

The three cooktop grates are designed for

specific positions. For maximum stability, these

grates should only be used in their proper position:

they should not be interchanged. For your

convenience, the undersides of the left and right

grates are marked "OUTSIDE" and "INSIDE". Make

sure that the side marked "OUTSIDE" is on the outer

edge of your cooktop. Make sure that the tubs

on either side of the center grate fit into the slots

located on the "INSIDE" edge

of the side grates.

"INSIDE"

edges

"OUTSIDE.... OUTSIDE"

edge edge

Tab Tab

Installation Instructions

OPERATION CHECKLIST

Hake sure all controls are left in the OFF

position. Check to be sure the cooktop is in the

UNLOCKED position (on models so equipped).

Hake sure the flow of air to and from the

cooktop is unobstructed.

The serial plate for your cooktop is located on

the bottom of the burner box. In addition to the

model and serial numbers, it tells you the ratings

of the burners and the type of fuel and pressure

the cooktop was adjusted for when it left the

factory.

When ordering parts, always include the serial

number, model number and a code letter to

ensure proper replacement parts.

Recheck Steps:

Double check to make sure everything

in this guide has been completed. Rechecking

steps will ensure safe use of the cooktop.

Installation Instructions

MAKING THE LP CONVERSION

If sold outside the U.S.and Canada:

-& WARNING: ,fyouwish to use this product

with Liquefied Petroleum (LP)gas containing greater

than 10% butane, you must purchase a butane

conversion kit. To order,

please call 1.888.664.8403 or 1.787.276.4051.

Model ButGne Kit #

JGP970 WB28T10229

ZGU36 WB28T10229

JGP975 WB28T10231

JGP963 WB28T10233

JGP630 WB28T10235

JGP628 WB28T10236

TOOLS YOU WILL NEED

FOR LP CONVERSION

Phillips-Head

Screwdriver

Pliers

Safety Glasses

7mm Nutdriver

No. 15 Torx-Head

Driver

Small Flat-Head

Screwdriver (4mm or

5/32" tip size, 60mm

long)

r_ SAFETY INFORMATION YOU

SHOULD KNOW

The pressure regulator and burner orifices (]re set

for natural gas. To use LP gas, the regulator and

burner orifices must be converted. The LP orifice

spuds for the cooktop burners can be located in the

literature package attached to the regulator.

--&CAUTION: The cooktop, as shipped from

the factory, is set for use with natural gas. If you

wish to use your cooktop with LP gas, you must

first replace the orifices and convert the pressure

regulator.

-&WARNING: This conversion must

be performed by a qualified installer or gas supplier

in (]ccordance with the manufacturer's instructions

and all codes and requirements of the authority

having jurisdiction. Failure to follow instructions could

result in serious injury or property damage. The

qualified agency performing this work assumes

responsibility for the conversion.

--&CAUTION: The following adjustments

must be mode before turning on the burner.

Failure to do so could result in serious injury. Be

sure pressure regulator has been converted as

described in Step 2.

[]

ADJUST YOUR COOKTOP FOR USE

WITH LP GAS

Disconnect oll electrical power, ot the moin

circuit breaker or fuse box.

Shut off the gas supply to the cooktop

by closing the manual shut-off valve.

Adjust the pressure regulator, by the following

instructions:

• Unscrew the cop.

• Ploce your thumb ogoinst the flot side of the

spring retoiner ond press down to remove

the retoiner.

• Carefully look at the spring retainer to locate

the NAT or LP position.

Cop Gosket

/ I---- Spring

/ _ L_JPropone

NAT. Position

Position

Pressure Regulator

• Turn the spring retoiner over so thot

LP is showing on the bottom.

• Snap the retainer buck into position.

• Screw the cup buck onto the regulator.

Installation Instructions

MAKING THE LP CONVERSION (CONT.)

CHANGE COOKTOP BURNER

ORIFICES

Remove the top grates,

burner cops, and burner

heads.

Remove the spark

igniters from the burner

bose (if required to

access the orifices).

Using o No. 15 "Torx"

head driver bit, remove

the screws holding the

burner bose in position.

emove This

Assembly

Orifice Spud Located

Through This Opening

Using u 7mm nut driver,

remove the top burner

orifices. These may be

accessed through the

hole in the cooktop.

Burner cap

18,000 BTUBurner

Ion some models)

Burner

cop

_Burner

Burner @head

base

Spark igniter

CHANGE COOKTOP BURNER

ORIFICES (CONT.)

NOTE: On most burners,

the orifices hove o spring- Retainer

loaded retaining ring Ground Ring

the hex head to hold the

orifice in the nut driver during

installation and removal. A

slight amount of force is required to push the nut

driver down over the ring.

Installation Instructions

CHANGE COOKTOP BURNER

ORIFICES {CONT.)

Locate the LP/Propmne orifices shipped

inside the literature package. They

will have a digit number and the letter "L" on

the side. (Important: Save the orifices

removed from the appliance

for future use.)

Each orifice will show a series of engraved

marks, (I, II, III, X or none),

located on the top.

These marks denote the precise location of each

orifice to the cooktop burner.

OOOO

18,000 BTU/HR Burner (on some models)

O he 18,000 BTU/HRburner has two orifices with

markings located in the sides only. (Seerating

plate on bottom of appliance).

NOTE: The main orifice is located low in the center

of the burner while the simmer orifice is located

higher behind the center of the burner.

Soirifmicmer_

Main orifice

Units with 4 burners

Units with 5 burners

Left Front Right Front

Model Orifice Orifice

JGP630 II III

JGP963 III X

JGP970

ZGU36K

Reploce: With:

JGP975 III Moin 206X N-_ 108X L

Simmer 57N -_ 34L

[]

Install the LP/Propune orifices in their precise

locutions us noted in the illustrations above.

Return the natural gas orifices to the bracket

and reattach the bracket and

the instruction sheet to the pressure regulator

using the screw removed previously.

Replace the burner bases, heads, cups and

top grates. (NOTE: When re-uttuchinq the

burner buses to qluss top units, tiqhten screws

to u maximum of

10 in.-Ibs torque.)

Installation Instructions

MAKING THE LP CONVERSION (CONT.)

ADJUST BURNER FLAMES

Turn all burners full on and check the flames.

They should be blue in color with some yellow

tipping at the ends of the flame. Foreign

particles in the gas line may cause an orange

flame at first, but this will soon disappear.

NOTE: For the 18,000 BTU/HR burner (on some

models) the cooktop burner knob should be

turned to the setting before the lowest setting.

This will ensure that the entire burner is

operating.

r_ Turn the cooktop burner knob to the lowest

setting while observing the flame.

Adjust the low flame setting using the valve bypass

screw as follows:

Low-setting adjustments must be made with two

other burners in operation on a medium setting.

This prevents the low flame from being set too low,

resulting in the flame being extinguished when

other burners are turned on.

E] To adjust the flame, remove the knobs. Insert

a screwdriver through the access hole in valve

switch. Engage

adjustment screw in

valve. Refer to the

illustration below that I

matches the adjustment

screw location for your

model.

If the flames were too

small or fluttered, open

the valve more than

the original setting.

If the flames blew

away from the burner,

close the valve more

than the original

setting.

Kburner

/only

r-_ Make the adjustment by slowly turning the

screw until flame appearance is correct.

Note: Some models may contain a siliconeshieldwhich

coversthe valve switch and access hole.A flashlight may

be requiredto locatethe access hole.Toaccessthe valve

adjusting screw,push the screwdriver through this shield.

After adjustment, reseat the shield around the switch hub

with your fingers, after withdrawing the screwdriver.

Reseat silicone shield

CORRECT INCORRECT

r_ Testing Flame Stability:

Test 1 - Turn the knob from "HI" to the lowest

setting quickly. If the flame goes out

at the lowest setting, increase the

flame size and test again.

Test 2 -

With the burner on the lowest setting,

open and close the cabinet door

under the cooktop. If the flame is

extinguished by the air currents

created by the door movement,

increase the flume height and test

again.

rF1 Flame Recheck:

After the adjustment is made, turn all burners off.

Ignite each burner individually. Observe the flame

at the "HI" position. Rotate the valve to the lowest

setting and be sure that the flame size decreases

as the valve is rotated counterclockwise.

TO CONVERT THE COOKTOP BACK TO NATURAL

GAS, REVERSETHE STEPS UNDER MAKING THE LP

CONVERSION.

Once the conversion is complete and checked

ok, fill out the LP sticker and include your name,

organization and date conversion was made. Apply

the sticker near the cooktop gas inlet opening to

alert others in the future that this appliance has

been converted to LP gas. If converting back to

natural gas from LP, please remove the sticker so

others know the appliance is set to use natural gas.

Instructions

d'installation

Table de cuisson scell

au gaz de 91 cm (36")

JGP628, JGP630, JGP963, JGP970,

JGP975, ZGU36

I P-1 Questions? Appelez le Centre de r_ponse 1.800.561.3344 ou visitez notre site

Web 8 I'adresse ' www.electromenagersge.ca

AVANT DE COMMENCER

Avant de commencer, lisez attentivement la totalit6

de ces instructions.

•IMPORTANT - Conservezces

instructionspour votreinspecteurlocal

•IMPORTANT - mespecteztoutesles

ordonnances etlescodes locoux.

• Note c_l'installateur- Assurez-vousde laissezces

instructionsau consommateur.

• Note au consommateur - Conservez ces

instructionspour r6f6rencefuture.

• Lo garantiene couvre aucune panne due c_une

mauvaise installation.

.AAVERTISSEMENT -

Cet appareil doit @trebien mis (_la terre.

•IMPORTANT - vousdevez

verifierque cetoppareiln'aitpos de fuite

conform6ment aux instructionsdu fabricant.

• L'installateur est responsable d'une bonne

installation et Io gorontie ne couvre aucune

panne due (_une mauvaise installation.

-AAV ERTISSEM ENT - D6brancheztout

couront61ectriqueou niveou du disjoncteurde Io

maison ou de laboTtec_fusiblesavant d'installer.

POUR VOTRE SI_CURITI_

-_ AVERTISSEMENT -

Si vous ne suivez pas exactement les instructions

de ce manuel, vous risquez d'occasionner un

incendie, une explosion

ou une fuite de gaz, qui peuvent provoquer des

dommages mat6riels, des blessures corporelles ou

la mort.

Ne conservez pos ou n'utilisezjomais d'essence

ou d'autres liquides ou vapeurs inflammables (_

proximit6 de cet appareil

ou de tout autre appareil m6naged

CI QUE VOUS DEVEZ FAIRE SI

VOUS SENTEZ LE GAZ :

• N'essoyezjomois d'ollumer un opporeil

61ectrom6nager. Ne touchez (_aucun

commutoteur d'61ectricit6, n'utilisez jamais un

t616phone dons votre b(_timent.

• Appelez imm6diatement votre fournisseur de

goz (_I'oide du t616phone d'un voisin. Suivez les

instructions de votre fournisseur de goz.

• Si vous ne pouvez pos entrer en contact avec

votre fournisseur de goz, appelez

les pompiers.

L'installation et le service de votre table de cuisson

doivent @trefoits par un installateur qualifi6, un

technicien de service ou votre fournisseur de gaz.

31-10612-4 (lO-lO GE) 1

Instructions d'installation

INSTRUCTIONS IMPORTANTES DE SI CURITI

La conception de votre table de cuisson a 6t6

approuv6 par I'ACNOR International. Vous trouverez

des pr6cautions _]prendre en mati_re de s6curit6

dans votre Guide d'utilisation et de soins. Lisez-les

attentivement.

• L'installation de votre table de cuisson

doit se conformer aux codes Iocaux ou, en

I'absence de codes Iocaux, au National Fuel Gas

Code, ANSI Z22E1/NFPA 54 Derni_re 6dition.

• Assurez-vous que votre table de cuisson soit

bien install6e par un installateur qualifi6 ou un

technicien de service.

• Pour 61iminer tout mouvement corporel

au dessus des brOleurs de votre table de cuisson,

6vitez de placer des armoires de cuisine au

dessus des brOleurs.

• N'installezjamais votre appareil pros d'une porte

d'entr6e ou dans un emplacement o0 un courant

d'air peut g@ner son usage.

PII_CES COMPRISES

2 vis

Bandes de mousse (Pour 2 Supports de fixation

les modules 6 surface en

verre seulement)

MATI_RIAUX DONT VOUS POUVEZ

AVOIR BESOIN

Agent de scellement Raccords de tuyaux Robinet d'alimentation

de tuyau de gaz

Raccord flexible de gaz approuv_ par I'ACNOR

DI min 3/8", Jonction NPT 1/2

BESOINS D'I_LECTRICITI_

Cet appareil m6nager doit _tre livr6 avec le ban

voltage et la bonne fr6quence et branch6 (_son

propre circuit de d6rivation bien mis 6 la terre,

prot6g6 par un disjoncteur ou un fusible qui ant

I'amp@age not6 sur la plaque min6ralogique de

votre appareil.

Nous vous recommandons de faire brancher le

ceblage 61ectrique et la fiche de votre cuisini_re

par un 61ectricien qualifi& Apr6s I'installation,

demandez 6 1'61ectricien de vous montrer

I'emplacement de votre coupe-circuit principal.

Demandez _]votre entreprise de services publics les

codes 61ectriques en vigueur

dans votre r6gion. En ne cOblant pas votre

cuisini_re conform6ment aux codes en vigueur,

vous provoquez une situation dangereuse. En

I'absence de codes, vous devez c0bler et isoler

votre cuisini_re conform6ment aux exigences du

Canadian Electrical Code.

OUTILS DONT VOUS AUREZ BESOINS

Crayon

Sciesauteuse

Tournevis Phillips

R@gle ordinaire ou de

v@ification

Lunettes de s@curit@

CI@6 tuyau

Perceuse 6 main ou _lectrique

et foret de 1/8po

Instructions d'lnstallation

LISTE DEVITRIFICATION AVANT INSTALLATION

Pour pr6parer I'ouverture de la surface de

cuisson, vous devez vous assurer que

I'int6rieur de I'armoire ne touche pas la table

de cuisson (consultez la section sur la

pr6paration de I'ouverture).

Enlevez les mat6riaux d'emballage, les

boTtes de grille, le r6gulateur avec sa

documentation et la documentation de

votre table de cuisson avant de commencer

6 I'installer.

_1_ Documentation

Bottes de

grille

2ballage_

de/

Table

cuisson

F61

Enlevez les instructions d'installation de la

trousse de documentation et lisez-les

soigneusement avant de commencer.

Assurez-vous de bien ranger toute la

documentation, le manuel d'utilisation et

d'entretien, etc. duns un endroit sOr pour

r6f6rence future.

Assurez-vous d'avoir tousles outils et tous

les mat6raux n6cessaires avant de

commencer 6 installer votre table de

cuisson.

rE1 Votre maison dolt @trealiment6e en courant

61ectrique ad6quat pour vous permettre de

bien utiliser en toute s6curit6 votre table de

cuisson. (Consultez la section sur les besoins

d'61ectricit&)

r_ Pour installer votre table de cuisson dans

votre maison, assurez-vous de vous

conformer scrupuleusement 6 tous les

codes et 6 toutes les ordonnances locales.

[]

Assurez-vous que les rev@tements

de mur, le comptoir et les armoires autour

de la table de cuisson puissent supporter la

chaleur [pouvant atteindre 93°C (200°F)]

produite par la table de cuisson.

PREPARATION

Instructions d'lnstallation

DE L°OUVERTURE

VOUS DEVEZ RESPECTER LES

DEGAGEMENTS MINIMAUX

Profondeur max de 33 cm (13") des

armoires en surplomb non prot6g6es D6gagement min. de 15

cm (6") d6coupage au

mur de c6t6 6 droite de

I'appareil

D6gagement min. de 76 cm (30") du

comptoir 6 la surface en non surplomb

non prot6g6es

D6gagement min

de 10 cm (3-3/4") du

d6coupage au tour de

c6t6 droite de I'appareil

Hauteur min

de 45 cm (18")

du comptoir

6 I'armoire la

plus proche de

chaque c6t6 de

I'appareil

REMARQUE : tous les mod61es de surface

6 cuisson au gaz requi6rent un d6gagement

de 1,1 cm (7/16 po) sous la hauteur de la surface

pour la mati6re combustible.

I_l DIMENSIONS DU DI_COUPAGE DE

LA TABLE DE CUISSON

55 cm (21")(54,6 cm [21-1/2"]

91 cm (56") "'"_1 "_'_ max. pour table de cuisson en

_'_ 8 cm (S')

verre)

48 cm (18-7/8") ..,,..I_,...-'--_

DIMENSIONS TOTALES DE LA

TABLE DE CUISSON

Pour assurer lajustesse du d6coupage,

il vaut mieux faire un gabarit pour couper

I'ouverture dans le comptoir.

86 cm (33-7/8 po)Iongueur

du d6coupage _ Largeur du d6coupage

_,5 cm_9- i/8")

! _--_.__-'--_ _ (16-15/16,,)

°(stancem(nde5,7cm _.-__J_l I

(2-1/4") de d6coupage au _'_i_r -_ _ I

murderrierelatablede / I_il)l _'

CUlSSOR " liT _I--

6,4 cm (2-i/2") Distance min.

de l'ar#te avant du d#coupage

de l'arr#te avant de la table de

cuisson

EMPLACEMENT RECOMMA.NDE_ DE

L'ALIMENTATION DE GAZ A

PARTIR DU MUR ARRII_RE

2,5 cm (1") min. du mur arri_re

Emplacement

recommand6 de

ralimentatbn Du

de gaz _ d6coupage 6

la ligne

du centre

F51 ASSUREZ-VOUS OUE LES

REVF:TEMENTS MUR, LE

COMPTOIR ET LES ARMOIRES

AUTOUR DE LA TABLE DE

CUISSON PUISSENT SUPPORTER

LA CHALEUR (POUVANT

ATTEINDRE 93°C [200°F])

Les rev#tements de

mur, lesarmoires et

le comptoir doivent

pouvoir supporter

une chaleru pouvant

atteindre 93°C (200°F)

La page charge ...

GE JGP330BEKBB - 30" Gas Cooktop Guide d'installation

Marque: GE

Modèle: JGP330BEKBB - 30" Gas Cooktop

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: GE JGP330BEKBB - 30" Gas Cooktop Installation guide

GE JGP330BEKBB - 30" Gas Cooktop Guide d'installation

GE JGP330BEKBB - 30" Gas Cooktop Guide d'installation

dans d''autres langues

Documents connexes

Autres documents