Installation
Instructions
36" SealedGasCooktop
JGP628, JGP630, JGP963, JGP9?0,
JGP9?5, ZGU36
I Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca
I
IN THE COMMONWEALTH OF
MASSACH USETTS:
• This product must be installed by u licensed
plumber or gas fitter.
• When using ball-type gas shut-off valves, they
shall be the T-handle type.
• A flexible gas connector, when used, must not
exceed 3 feet.
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
•IMPORTANT - Savetheseinstructions
forlocalinspector'suse.
•IMPORTANT - Observeallgoverning
codes and ordinances.
• Note to Installer- Be sure to leave these
instructions with the Consumer.
• Note to Consumer - Keep these instructions for
future reference.
• Product failure due to improper installation is not
covered under the Warranty.
-&WARNING - This appliance must be
properly grounded.
• IMPORTANT - Leak testingofthe
applianceshallbe conducted accordingto the
manufacturer'sinstructions.
• Proper installation is the responsibility
of the installer and product failure due to
improper installation is NOT covered under
warranty.
-AWARNING - Disconnectallelectrical
power atthe main circuit breaker
or fuse box before installing.
FOR YOUR SAFETY:
-&WARNING - Iftheinformation
in this manual is not followed exactly, a fire,
explosion or gas leak may result causing property
damage, personal injury or death.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance!
WHAT TO DO IF YOU SMELL
GAS:
Do not try to light any appliance. Do not touch
any electrical switch; do not use any phone in
your building.
Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire
department.
Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
This cooktop has been design certified
by CSA International. You'll find safety precautions
in your Owner's Manual.
Read them carefully.
Installation of this cooktop must conform with
local codes or, in the absence of local codes with
the National Fuel Gas Code, ANSI Z223.1/NFPA
54-Latest edition.
Be sure your cooktop is installed properly by a
qualified installer or service technician.
To eliminate reaching over surface burners,
cabinet storage above burner should be avoided.
Do not install the unit near an outside door or
where a draft may affect its use.
31-i0612-4 (lO-lO GE) 1
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
ELECTRICAL REQUIREMENTS
This appliance must be supplied with the proper
voltage and frequency and connected to an
individual, properly grounded branch circuit,
protected by a circuit breaker or fuse having
amperage as noted on the rating plate.
We recommend you have the electrical wiring and
hookup of your cooktop connected by a qualified
electrician. After installation, have the electrician
show you where your main cooktop disconnect is
located.
Check with your local utilities for electrical codes
which apply in your area. Failure to wire your
cooktop according to governing codes could result
in a hazardous condition.
If there are no codes, your cooktop must be wired
and fused to meet the requirements of the National
Electrical Code, ANSl/NFPA No. 70--Latest edition.
You can get a copy by writing:
National Fire Protection Association
Batterymarch Park
Quincy, IVlA 02269
In Canada your cooktop must be wired and fused
to meet the requirements of the Canadian Electrical
Code.
Be sure the installation of this product in a mobile
home conforms with the Manufactured Home
Construction and
Safety Standard, Title 24 CFR, Part 3280.
If this standard does not apply, you must follow
the standard for Manufactured Home Installations,
ANSI A225.1 and Manufactured Home Installations,
Sites and Communities and ANSI/NFPA S01A or
with local codes.
You can get a copy of the Federal Standard by
Writing:
Office of Mobile Home Standards
HUD Building
451 7th Street, S.W.
Washington, D.C. 24010
PARTS INCLUDED
2 Screws
Foam Tape
(GlassTop
Models Only)
2 Hold
Down Brackets
MATERIALS YOU MAY NEED
Joint Sealant Pipe Fittings
Shut-Off Valve
CSA-Approved Flexible Gas Line
3/8" Min. ID, 1/2" NPTConnection,
3-foot Maximum Length (Massachusetts Only)
TOOLS YOU WILL NEED
FOR INSTALLATION
I IIf_( ( _ /,(---]/ ]]
Pencil
Saber Saw
Phillips-Head
Screwdriver
Ruler or Straightedge
Safety Glasses
Pipe Wrench
1/8" Drill Bit & Electric or
Hand Drill
Installation Instructions
PRE-INSTALLATION CHECKLIST
_3
F_
When preparing cooktop opening, make
sure the inside of the cabinet and the
cooktop do not interfere with each other.
(See section on preparing the opening.)
Remove packaging materials, grate boxes,
regulator with literature, and literature
package from the cooktop before beginning
installation.
Package
Grate boxes
Foam_ _
Pac _ [_3_ i] _j
Cool<top J
E1
r61
[]
FF1
Remove Installation Instructions from
literature pack and read them carefully
before you begin.
Be sure to place all literature, Use and Care,
Installations, etc. in a safe place
for future reference.
Make sure you have all the tools and
materials you need before starting the
installation of the cooktop.
Your home must provide the adequate
electrical service needed to safely and
properly use your cooktop. (Refer to section
on electrical requirements.)
When installing your cooktop in your home,
make sure all local codes and ordinances
are followed exactly as stated.
Make sure the wall coverings, countertop
and cabinets around the cooktop can
withstand heat (up to 200°F) generated by
the cooktop.
Instollotion Instructions
PREPARING THE OPENING
MAINTAIN THE FOLLOWING
MINIMUM CLEARANCE
DIMENSIONS
13" MAX.Depth of unprotected
overhead cabinets
\\ 6" MIN. clearance from
cutout to side wall on the
right of the unit
30" MIN. clearance from countertop
to unprotected overhead surface
18" MIN. height
from countertop to
nearest cabinet on
either side of unit
3-3/4" MIN.clearance from
cutout to side wall on the
left of the unit
NOTE:All gas cooktop models require 7/16"
free area below cooktop height to combustible
material.
I_l OVERALL COOKTOP DIMENSIONS
21" (21-1/4" IVlax.for
CUTOUT DIMENSIONS OF
COUNTERTOP
To ensure accuracy, it is best to make
a template when cutting the opening
in the counter.
_-1/8 _"width cut
length _ 16-15/16"
2-1/4" Min. B of cutcutout and the wail
behind the cooktop
2-1/2" Min. from
front edge of cutout
and front edge of
countertop
RECOMMENDED GAS SUPPLY
LOCATION FROM BACKWALL
Recommended
gas supply
location
l" Min. From Backwall
From Cutout
Center Line
F51 MAKE SURE WALL COVERINGS,
COUNTERTOP AND CABINETS
AROUND COOKTOP CAN
WITHSTAND HEAT {UP TO 200°F)
GENERATED BY COOKTOP
Wall covering,
cabinets and
countertop must
withstand heat
up to 200°F
Installation Instructions
INSTALLING THE COOKTOP UNIT
B3
LOCATE ELECTRICAL OUTLET AND
GAS SHUT-OFF VALVE BENEATH
CABINET
NEVER REUSEOLD
CONNECTORS WHEN
INSTALLING THIS
UNIT.
H I
J_J
U
shutoff11i\
_L Valve r_ I Electrical
II Outlet 12"
I Below
Countertop
Install a manual shut-off valve in the gas line in an
easily accessible location outside the cooktop. Be
sure you know how and where to shut off the gas
supply to the cooktop. Install the electrical outlet
12" below the countertop.
_-I PROTECT SURFACE OF COOKTOP
Place a towel or tablecloth onto the
countertop. Lay the cooktop upside down onto the
protected surface.
Bottom of cooktop
Cloth under Cooktop
[_] ATTACH FOAM TAPE
(glass maintop models only)
Apply the foam tape around the outer edge
of the glass. Do not overlap the foam tapes.
Bottom of Cooktop
\ Foam Topes
\
Cooktop Gloss
LOCATE MOUNTING PARTS
Remove the hold down brackets from the
literature package.
_-I ATTACH BRACKETS TO COOKTOP
Remove the screw from the bottom of the
cooktop and screw the hold-down bracket
to the side of the cooktop unit. Repeat for opposite
side of cooktop.
Pre-drilled
Bottom
of Cooktop
.\.._ Foem Topes
Cooktop
Gloss
I-_ INSERT COOKTOP INTO CUTOUT
Insert the cooktop centered into the cutout
opening. Make sure the front edge of the countertop
is parallel to the cooktop. Make final check that all
required clearances are met.
Once the unit is in place, screw the hold- down
bracket into the cabinet sides to secure the unit
into place.
Installation Instructions
INSTALLATION--GAS CONNECTIONS
PROVIDE ADEQUATE
GAS SUPPLY
This cooktop is designed to operate on natural gas
at 4" of water column manifold pressure and 7" of
water column (W.C.) supply pressure. It is shipped
from the factory set for natural gas. The convertible
pressure regulator supplied with the unit must
be connected in series with the manifold of the
cooktop and must remain in series with the supply
line regardless of whether natural or L.P.gas is
being used.
FOR PROPEROPERATION, THE MAXIMUM INLET
PRESSURETO THE REGULATOR MUST BE NO MORE
THAN 14" OF WATER COLUMN PRESSURE.For
checking the regulator, the inlet pressure must
be at least 1" W.C.. (or 3.4 KPA) greater than the
regulator output setting. If the regulator is set for 4"
W.C. of water column pressure, the inlet pressure
must be at least 5" W.C. If the regulator is set for
10" W.C., the inlet pressure must be at least 11"
W.C.. The gas supply line to the cooktop should be
1/2" or 3/4" pipe.
_-I INSTALL REGULATOR
NEVER REUSEOLD CONNECTORS WHEN
INSTALLING THIS COOKTOP.
-A WARNING: Neverreuseold
flexible connectors. The use of old flexible
connectors can cause gas leaks and personal
injury. Always use new flexible connectors when
installing u gas appliance.
Screw a section of pipe onto
the inlet end of the pressure
regulator and install the
coupling.
Pressure _l
Regulator
Coupling _
To reduce the likelihood of gas leaks, apply teflon
tape or a thread compound approved for use with
LP or Natural gases to all threaded connections.
INSTALL REGULATOR ONTO
BURNER BOX BOTTOM
Screw the regulator
onto
the burner box
bottom pipe
connection.
Make sure the
top of the regulator
is
facing towards the
cabinet front, easily
accessible through
the cabinet doors.
I
I
Pressure __._
Regulator
Coupling --I
Shut-Off
Valve
LI
i\
II Electrical
I Outlet 12"
I Below
Countertop
COMPLETE CONNECTION WITH A
COUPLING
Complete the
connection between
the regulator pipe
coupling and
the shut-off valve.
I
I
Pressure
Regulator
Coupling --_
Shut-Off _:
Valve --'_
U
II Electrical
I Outlet 12"
I Below
Countertop
Installation Instructions
CHECK FOR LEAKS
Before testing for leaks, make sure oll burner knobs
ore in the OFF position.
After connecting the cooktop to gas, check system
for leaks with o manometer. If a manometer is not
available, turn the gas supply on to the cooktop
and use o liquid leak detector at oil joints and
connections to check for leaks.
Tighten oil connections if necessary to prevent gas
leakage in the cooktop or supply line.
DO NOT USE OPEN FLAME TO CHECK FOR
LEAKS!
Disconnect the cooktop and its individual shut-off
valve from the gas supply piping system during any
pressure testing of that system at test pressures
greater than 1/2 psig (3.5 kPa).
Isolate the cooktop from the gas supply piping
system by closing its individual shut-off valve
during any pressure testing of the gas supply
system at test pressures equal to or less than
1/2 psig (3.5 kPa).
INSTALLATION OVER
BUILT-IN OVEN
See built-in oven installation for complete
installation instructions.
I
T
I _ s,,ToCenterof
| I _] 2" Dia. Hole From
_ _ Countertop
90 ° Elbow ........ I ---'_--
7 _1"_ 2"Dia.Hole
(20 7/8" from front
of Countertop to
Hole Center}
Cabinet Sides
Installation Instructions
INSTALLATION--ELECTRICAL CONNECTIONS
_AWARNING - Disconnectoilelectricol
power ot the moin circuit breoker or fuse box
before instolling.
EXTENSION CORDS
Because of potential safety hazords under certoin
conditions, we strongly recommend against the
use of an extension cord. However, if you still
elect to use an extension cord, it is absolutely
necessary that it be a UL listed B-wire grounding
type applionce extension cord ond thot the
current carrying rating of the cord in amperes be
equivalent to or greoter than the branch circuit
roting. Such extension cords ore obtoinoble
through your Iocol opplionce deoler.
IMPORTANT: (Pleosereod corefully)FOR
PERSONAL SAFETY,THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
ELECTRICAL SUPPLY AND OUTLET
An odequote electricol supply ond outlet must
be used to operote the electricol ports of your
cooktop.
The power cord of this applionce is equipped
with o 3-prong (grounding) plug which must
be used with o properly grounded 3-hole
outlet with u standard 120 Volt, 60 cycle AC
household current.
If you do not hove o 3-hole grounded outlet,
hove o quolified electricion chonge your old
one.
A grounding odoptor will be needed
to convert the old one until the outlet
con be reploced. This method is only
temporary, ond o qualified electrician should
test it to be sure it meets requirements.
Ensure proper
L groundond
firmconnection
beforeuse
TWO-PRONG WALL RECEPTACLE
Where a standard 2-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the customer to hove it replaced with
u properly grounded B-prong wall receptacle.
Do not under any circumstonces cut or remove
grounding prong from the cooktop cord. Failure
to provide proper polarization may create u
hazardous condition.
Installation Instructions
USAGE SITUATIONS WHERE
APPLIANCE POWER CORD
WILL BE DISCONNECTED
INFREQUENTLY
For 15 amp circuit only. Do not use an adaptor
on a 20 amp circuit. Where local codes permit, a
TEMPORARY CONNECTION may be made to a properly
grounded two-prong wall receptacle by the use of a
UL-listed adaptor available at most hardware stores.
The larger slot in the adaptor must be aligned with
the large slot in the wall receptacle to provide proper
polarity in the connection of the power cord.
Ensure proper ground and firm
_. connection before use
Alignlarge
prongs/slots
Temporary Method
(Adaptor plugs not permitted in Canada)
-ACAUTION: Attachingthe adaptor ground
terminaltothe wallreceptaclecoverscrew does not
ground the applianceunlessthe screw ismetal,and
notinsulated,and the wallreceptacleisgrounded
through the house wiring.The customer should have
the circuitchecked by a qualifiedelectriciantomake
surethe receptacleisproperlygrounded.
When disconnecting the power cord from the
adaptor, always hold the adaptor with one hand. If
this is not done, the adaptor ground terminal is very
likely to break with repeated use. Should this happen,
DO NOT USE the appliance until a proper ground has
again been established.
Usage situation where appliance power cord will be
disconnected frequently.
Do not use an adaptor plug in these situations
because disconnection of the power cord places
undue strain on the adaptor and leads to eventual
failure of the adaptor ground terminal. The customer
should have the 2-prong receptacle replaced with
a 3-prong (grounding) receptacle by a qualified
electrician before using the appliance.
Installation Instructions
COOKTOP BURNERS
ASSEMBLING THE COOKTOP
BURNERS
The electrode of the spark igniter is exposed. Be
careful not to push any cooktop controls while the
top of the burner is removed.
Do not remove the top or touch the electrode
of any burner while another burner is turned on.
Electrical shock might result.
Reploce the burner head onto the burner
bose, making sure that the heod is properly
oriented over the burner bose ond the
electrode. Moke sure to place
the correct burner head on the correct burner
bose and thor the burner head sits level on
the burner bose. The burner heads ore not
interchongeoble.
[]
Place the burner
cops on the burner
heads, making sure
to place the correct
burner cop on the
correct burner
head. The burner
cops ore not
interchangeable.
Make sure that the
burner cops ore
properly seated on
the burner heads.
Burner cop properly seoted
Burner cop not properly seoted
[]
Make sure the pins in
the burner heads
match the burner
bose indentutions
und that they ore
properly seated in
them by rotating the
heuds until they ore
level.
Make sure the slot in
the burner head
is positioned
over the
electrode. The
burner cup has
three to four
pins. When
replucing the
cup, make
sure none of
the pins sits
in the stability
chamber.
Burner cop
Burner heod
_ectrode
__Burner
Pin base
indentations
Stabilit_
chamber _
Electrode
Burnerbase
Make sure the hole Burner cop
in the burner head
assembly ispositioned
over the electrode and Burner head
that the burner heod is ossembly_r_-_]b,
fully inserted inside the
burner bose. A small
gop between the bose
and head is normal.
Electrode Burner
bose
10
Installation Instructions
[_ CHECK IGNITERS
Operation of the electric igniters should be
checked after the cooktop and supply line have
been carefully checked for leaks and the cooktop
has been connected to the electrical power.
On models so equipped, check to be sure the
cooktop is in the UNLOCKED position.
r_ Push and turn a burner valve to the LITE
position. All spark igniters will make a series of
sparks (ticking sounds), but only the burner
turned to LITE will light.
• The burner should light when gas is
available to the burner.
• Once the burner lights, it should be turned
out of the LITE position.
r_ Try each valve separately until all burners
have been checked.
_-I BURNER IGNITION
Cooktop Spark Ignition-When you turn the
cooktop knob to LITE,the spark igniter makes u
series of electric sparks (ticking sounds) which light
the burner. During a power failure, the burners will
not light automatically. In an emergency, a cooktop
burner may be lit with a match by following the
steps below.
-&WARNING: Lighting gas burners with a
match is dangerous. You should match light the
cooktop burners only in an emergency.
On models so equipped, check to be sure the
cooktop is in the UNLOCKED position.
r-_ Light a match and hold the flame near the
burner you want to light. Wooden matches
work best.
r_ Push in and turn the control knob slowly. Be
sure you are turning the correct knob for the
burner you are lighting.
NOTE: If the burner does not light within five seconds,
turn the knob off and wait one minute before trying
again.
THE BURNER FLAMES
Turn each burner on. Flames should be blue in color
with no trace of yellow. The burner flames should
not flutter or blow away from the burner. The flame
should be no less than 1/4" on the lowest setting
and no greater than 1-1/2" on highest setting.
-&WARNING: ,fyouattempt to measure
the flame, please use caution.
Burns could result.
Cooktop Burner
Burners should be checked frequently
I-_ BURNER GRATES
The three cooktop grates are designed for
specific positions. For maximum stability, these
grates should only be used in their proper position:
they should not be interchanged. For your
convenience, the undersides of the left and right
grates are marked "OUTSIDE" and "INSIDE". Make
sure that the side marked "OUTSIDE" is on the outer
edge of your cooktop. Make sure that the tubs
on either side of the center grate fit into the slots
located on the "INSIDE" edge
of the side grates.
"INSIDE"
edges
"OUTSIDE.... OUTSIDE"
edge edge
Tab Tab
11
Installation Instructions
OPERATION CHECKLIST
Hake sure all controls are left in the OFF
position. Check to be sure the cooktop is in the
UNLOCKED position (on models so equipped).
Hake sure the flow of air to and from the
cooktop is unobstructed.
The serial plate for your cooktop is located on
the bottom of the burner box. In addition to the
model and serial numbers, it tells you the ratings
of the burners and the type of fuel and pressure
the cooktop was adjusted for when it left the
factory.
@
RI
When ordering parts, always include the serial
number, model number and a code letter to
ensure proper replacement parts.
Recheck Steps:
Double check to make sure everything
in this guide has been completed. Rechecking
steps will ensure safe use of the cooktop.
12
Installation Instructions
MAKING THE LP CONVERSION
If sold outside the U.S.and Canada:
-& WARNING: ,fyouwish to use this product
with Liquefied Petroleum (LP)gas containing greater
than 10% butane, you must purchase a butane
conversion kit. To order,
please call 1.888.664.8403 or 1.787.276.4051.
Model ButGne Kit #
JGP970 WB28T10229
ZGU36 WB28T10229
JGP975 WB28T10231
JGP963 WB28T10233
JGP630 WB28T10235
JGP628 WB28T10236
TOOLS YOU WILL NEED
FOR LP CONVERSION
Phillips-Head
Screwdriver
Pliers
Safety Glasses
7mm Nutdriver
No. 15 Torx-Head
Driver
Small Flat-Head
Screwdriver (4mm or
5/32" tip size, 60mm
long)
r_ SAFETY INFORMATION YOU
SHOULD KNOW
The pressure regulator and burner orifices (]re set
for natural gas. To use LP gas, the regulator and
burner orifices must be converted. The LP orifice
spuds for the cooktop burners can be located in the
literature package attached to the regulator.
--&CAUTION: The cooktop, as shipped from
the factory, is set for use with natural gas. If you
wish to use your cooktop with LP gas, you must
first replace the orifices and convert the pressure
regulator.
-&WARNING: This conversion must
be performed by a qualified installer or gas supplier
in (]ccordance with the manufacturer's instructions
and all codes and requirements of the authority
having jurisdiction. Failure to follow instructions could
result in serious injury or property damage. The
qualified agency performing this work assumes
responsibility for the conversion.
--&CAUTION: The following adjustments
must be mode before turning on the burner.
Failure to do so could result in serious injury. Be
sure pressure regulator has been converted as
described in Step 2.
[]
ADJUST YOUR COOKTOP FOR USE
WITH LP GAS
Disconnect oll electrical power, ot the moin
circuit breaker or fuse box.
Shut off the gas supply to the cooktop
by closing the manual shut-off valve.
Adjust the pressure regulator, by the following
instructions:
• Unscrew the cop.
• Ploce your thumb ogoinst the flot side of the
spring retoiner ond press down to remove
the retoiner.
• Carefully look at the spring retainer to locate
the NAT or LP position.
Cop Gosket
/ I---- Spring
/ _ L_JPropone
NAT. Position
Position
Pressure Regulator
• Turn the spring retoiner over so thot
LP is showing on the bottom.
• Snap the retainer buck into position.
• Screw the cup buck onto the regulator.
13
Installation Instructions
MAKING THE LP CONVERSION (CONT.)
CHANGE COOKTOP BURNER
ORIFICES
Remove the top grates,
burner cops, and burner
heads.
Remove the spark
igniters from the burner
bose (if required to
access the orifices).
Using o No. 15 "Torx"
head driver bit, remove
the screws holding the
burner bose in position.
emove This
Assembly
Orifice Spud Located
Through This Opening
Using u 7mm nut driver,
remove the top burner
orifices. These may be
accessed through the
hole in the cooktop.
Burner cap
18,000 BTUBurner
Ion some models)
Burner
cop
_Burner
Burner @head
base
Spark igniter
CHANGE COOKTOP BURNER
ORIFICES (CONT.)
NOTE: On most burners,
the orifices hove o spring- Retainer
loaded retaining ring Ground Ring
the hex head to hold the
orifice in the nut driver during
installation and removal. A
slight amount of force is required to push the nut
driver down over the ring.
14
Installation Instructions
CHANGE COOKTOP BURNER
ORIFICES {CONT.)
Locate the LP/Propmne orifices shipped
inside the literature package. They
will have a digit number and the letter "L" on
the side. (Important: Save the orifices
removed from the appliance
for future use.)
Each orifice will show a series of engraved
marks, (I, II, III, X or none),
located on the top.
These marks denote the precise location of each
orifice to the cooktop burner.
OOOO
18,000 BTU/HR Burner (on some models)
O he 18,000 BTU/HRburner has two orifices with
markings located in the sides only. (Seerating
plate on bottom of appliance).
NOTE: The main orifice is located low in the center
of the burner while the simmer orifice is located
higher behind the center of the burner.
Soirifmicmer_
Main orifice
Units with 4 burners
Units with 5 burners
Left Front Right Front
Model Orifice Orifice
JGP630 II III
JGP963 III X
JGP970
ZGU36K
Reploce: With:
JGP975 III Moin 206X N-_ 108X L
Simmer 57N -_ 34L
[]
[]
[]
Install the LP/Propune orifices in their precise
locutions us noted in the illustrations above.
Return the natural gas orifices to the bracket
and reattach the bracket and
the instruction sheet to the pressure regulator
using the screw removed previously.
Replace the burner bases, heads, cups and
top grates. (NOTE: When re-uttuchinq the
burner buses to qluss top units, tiqhten screws
to u maximum of
10 in.-Ibs torque.)
15
Installation Instructions
MAKING THE LP CONVERSION (CONT.)
ADJUST BURNER FLAMES
Turn all burners full on and check the flames.
They should be blue in color with some yellow
tipping at the ends of the flame. Foreign
particles in the gas line may cause an orange
flame at first, but this will soon disappear.
NOTE: For the 18,000 BTU/HR burner (on some
models) the cooktop burner knob should be
turned to the setting before the lowest setting.
This will ensure that the entire burner is
operating.
r_ Turn the cooktop burner knob to the lowest
setting while observing the flame.
Adjust the low flame setting using the valve bypass
screw as follows:
Low-setting adjustments must be made with two
other burners in operation on a medium setting.
This prevents the low flame from being set too low,
resulting in the flame being extinguished when
other burners are turned on.
E] To adjust the flame, remove the knobs. Insert
a screwdriver through the access hole in valve
switch. Engage
adjustment screw in
valve. Refer to the
illustration below that I
matches the adjustment
screw location for your
model.
If the flames were too
small or fluttered, open
the valve more than
the original setting.
If the flames blew
away from the burner,
close the valve more
than the original
setting.
Kburner
/only
r-_ Make the adjustment by slowly turning the
screw until flame appearance is correct.
Note: Some models may contain a siliconeshieldwhich
coversthe valve switch and access hole.A flashlight may
be requiredto locatethe access hole.Toaccessthe valve
adjusting screw,push the screwdriver through this shield.
After adjustment, reseat the shield around the switch hub
with your fingers, after withdrawing the screwdriver.
Reseat silicone shield
CORRECT INCORRECT
r_ Testing Flame Stability:
Test 1 - Turn the knob from "HI" to the lowest
setting quickly. If the flame goes out
at the lowest setting, increase the
flame size and test again.
Test 2 -
With the burner on the lowest setting,
open and close the cabinet door
under the cooktop. If the flame is
extinguished by the air currents
created by the door movement,
increase the flume height and test
again.
rF1 Flame Recheck:
After the adjustment is made, turn all burners off.
Ignite each burner individually. Observe the flame
at the "HI" position. Rotate the valve to the lowest
setting and be sure that the flame size decreases
as the valve is rotated counterclockwise.
TO CONVERT THE COOKTOP BACK TO NATURAL
GAS, REVERSETHE STEPS UNDER MAKING THE LP
CONVERSION.
Once the conversion is complete and checked
ok, fill out the LP sticker and include your name,
organization and date conversion was made. Apply
the sticker near the cooktop gas inlet opening to
alert others in the future that this appliance has
been converted to LP gas. If converting back to
natural gas from LP, please remove the sticker so
others know the appliance is set to use natural gas.
16
Instructions
d'installation
Table de cuisson scell
au gaz de 91 cm (36")
JGP628, JGP630, JGP963, JGP970,
JGP975, ZGU36
I P-1 Questions? Appelez le Centre de r_ponse 1.800.561.3344 ou visitez notre site
Web 8 I'adresse ' www.electromenagersge.ca
I
AVANT DE COMMENCER
Avant de commencer, lisez attentivement la totalit6
de ces instructions.
•IMPORTANT - Conservezces
instructionspour votreinspecteurlocal
•IMPORTANT - mespecteztoutesles
ordonnances etlescodes locoux.
• Note c_l'installateur- Assurez-vousde laissezces
instructionsau consommateur.
• Note au consommateur - Conservez ces
instructionspour r6f6rencefuture.
• Lo garantiene couvre aucune panne due c_une
mauvaise installation.
.AAVERTISSEMENT -
Cet appareil doit @trebien mis (_la terre.
•IMPORTANT - vousdevez
verifierque cetoppareiln'aitpos de fuite
conform6ment aux instructionsdu fabricant.
• L'installateur est responsable d'une bonne
installation et Io gorontie ne couvre aucune
panne due (_une mauvaise installation.
-AAV ERTISSEM ENT - D6brancheztout
couront61ectriqueou niveou du disjoncteurde Io
maison ou de laboTtec_fusiblesavant d'installer.
POUR VOTRE SI_CURITI_
-_ AVERTISSEMENT -
Si vous ne suivez pas exactement les instructions
de ce manuel, vous risquez d'occasionner un
incendie, une explosion
ou une fuite de gaz, qui peuvent provoquer des
dommages mat6riels, des blessures corporelles ou
la mort.
Ne conservez pos ou n'utilisezjomais d'essence
ou d'autres liquides ou vapeurs inflammables (_
proximit6 de cet appareil
ou de tout autre appareil m6naged
CI QUE VOUS DEVEZ FAIRE SI
VOUS SENTEZ LE GAZ :
• N'essoyezjomois d'ollumer un opporeil
61ectrom6nager. Ne touchez (_aucun
commutoteur d'61ectricit6, n'utilisez jamais un
t616phone dons votre b(_timent.
• Appelez imm6diatement votre fournisseur de
goz (_I'oide du t616phone d'un voisin. Suivez les
instructions de votre fournisseur de goz.
• Si vous ne pouvez pos entrer en contact avec
votre fournisseur de goz, appelez
les pompiers.
L'installation et le service de votre table de cuisson
doivent @trefoits par un installateur qualifi6, un
technicien de service ou votre fournisseur de gaz.
31-10612-4 (lO-lO GE) 1
Instructions d'installation
INSTRUCTIONS IMPORTANTES DE SI CURITI
La conception de votre table de cuisson a 6t6
approuv6 par I'ACNOR International. Vous trouverez
des pr6cautions _]prendre en mati_re de s6curit6
dans votre Guide d'utilisation et de soins. Lisez-les
attentivement.
• L'installation de votre table de cuisson
doit se conformer aux codes Iocaux ou, en
I'absence de codes Iocaux, au National Fuel Gas
Code, ANSI Z22E1/NFPA 54 Derni_re 6dition.
• Assurez-vous que votre table de cuisson soit
bien install6e par un installateur qualifi6 ou un
technicien de service.
• Pour 61iminer tout mouvement corporel
au dessus des brOleurs de votre table de cuisson,
6vitez de placer des armoires de cuisine au
dessus des brOleurs.
• N'installezjamais votre appareil pros d'une porte
d'entr6e ou dans un emplacement o0 un courant
d'air peut g@ner son usage.
PII_CES COMPRISES
2 vis
Bandes de mousse (Pour 2 Supports de fixation
les modules 6 surface en
verre seulement)
MATI_RIAUX DONT VOUS POUVEZ
AVOIR BESOIN
Agent de scellement Raccords de tuyaux Robinet d'alimentation
de tuyau de gaz
Raccord flexible de gaz approuv_ par I'ACNOR
DI min 3/8", Jonction NPT 1/2
BESOINS D'I_LECTRICITI_
Cet appareil m6nager doit _tre livr6 avec le ban
voltage et la bonne fr6quence et branch6 (_son
propre circuit de d6rivation bien mis 6 la terre,
prot6g6 par un disjoncteur ou un fusible qui ant
I'amp@age not6 sur la plaque min6ralogique de
votre appareil.
Nous vous recommandons de faire brancher le
ceblage 61ectrique et la fiche de votre cuisini_re
par un 61ectricien qualifi& Apr6s I'installation,
demandez 6 1'61ectricien de vous montrer
I'emplacement de votre coupe-circuit principal.
Demandez _]votre entreprise de services publics les
codes 61ectriques en vigueur
dans votre r6gion. En ne cOblant pas votre
cuisini_re conform6ment aux codes en vigueur,
vous provoquez une situation dangereuse. En
I'absence de codes, vous devez c0bler et isoler
votre cuisini_re conform6ment aux exigences du
Canadian Electrical Code.
OUTILS DONT VOUS AUREZ BESOINS
Crayon
Sciesauteuse
Tournevis Phillips
R@gle ordinaire ou de
v@ification
Lunettes de s@curit@
CI@6 tuyau
Perceuse 6 main ou _lectrique
et foret de 1/8po
Instructions d'lnstallation
LISTE DEVITRIFICATION AVANT INSTALLATION
_3
r_
Pour pr6parer I'ouverture de la surface de
cuisson, vous devez vous assurer que
I'int6rieur de I'armoire ne touche pas la table
de cuisson (consultez la section sur la
pr6paration de I'ouverture).
Enlevez les mat6riaux d'emballage, les
boTtes de grille, le r6gulateur avec sa
documentation et la documentation de
votre table de cuisson avant de commencer
6 I'installer.
_1_ Documentation
Bottes de
grille
2ballage_
de/
Table
cuisson
E1
F61
Enlevez les instructions d'installation de la
trousse de documentation et lisez-les
soigneusement avant de commencer.
Assurez-vous de bien ranger toute la
documentation, le manuel d'utilisation et
d'entretien, etc. duns un endroit sOr pour
r6f6rence future.
Assurez-vous d'avoir tousles outils et tous
les mat6raux n6cessaires avant de
commencer 6 installer votre table de
cuisson.
rE1 Votre maison dolt @trealiment6e en courant
61ectrique ad6quat pour vous permettre de
bien utiliser en toute s6curit6 votre table de
cuisson. (Consultez la section sur les besoins
d'61ectricit&)
r_ Pour installer votre table de cuisson dans
votre maison, assurez-vous de vous
conformer scrupuleusement 6 tous les
codes et 6 toutes les ordonnances locales.
[]
Assurez-vous que les rev@tements
de mur, le comptoir et les armoires autour
de la table de cuisson puissent supporter la
chaleur [pouvant atteindre 93°C (200°F)]
produite par la table de cuisson.
PREPARATION
Instructions d'lnstallation
DE L°OUVERTURE
VOUS DEVEZ RESPECTER LES
DEGAGEMENTS MINIMAUX
SUIVANT
Profondeur max de 33 cm (13") des
armoires en surplomb non prot6g6es D6gagement min. de 15
cm (6") d6coupage au
mur de c6t6 6 droite de
I'appareil
D6gagement min. de 76 cm (30") du
comptoir 6 la surface en non surplomb
non prot6g6es
D6gagement min
de 10 cm (3-3/4") du
d6coupage au tour de
c6t6 droite de I'appareil
Hauteur min
de 45 cm (18")
du comptoir
6 I'armoire la
plus proche de
chaque c6t6 de
I'appareil
REMARQUE : tous les mod61es de surface
6 cuisson au gaz requi6rent un d6gagement
de 1,1 cm (7/16 po) sous la hauteur de la surface
pour la mati6re combustible.
I_l DIMENSIONS DU DI_COUPAGE DE
LA TABLE DE CUISSON
55 cm (21")(54,6 cm [21-1/2"]
91 cm (56") "'"_1 "_'_ max. pour table de cuisson en
_'_ 8 cm (S')
verre)
48 cm (18-7/8") ..,,..I_,...-'--_
DIMENSIONS TOTALES DE LA
TABLE DE CUISSON
Pour assurer lajustesse du d6coupage,
il vaut mieux faire un gabarit pour couper
I'ouverture dans le comptoir.
86 cm (33-7/8 po)Iongueur
du d6coupage _ Largeur du d6coupage
_,5 cm_9- i/8")
! _--_.__-'--_ _ (16-15/16,,)
°(stancem(nde5,7cm _.-__J_l I
(2-1/4") de d6coupage au _'_i_r -_ _ I
murderrierelatablede / I_il)l _'
CUlSSOR " liT _I--
6,4 cm (2-i/2") Distance min.
de l'ar#te avant du d#coupage
de l'arr#te avant de la table de
cuisson
EMPLACEMENT RECOMMA.NDE_ DE
L'ALIMENTATION DE GAZ A
PARTIR DU MUR ARRII_RE
2,5 cm (1") min. du mur arri_re
Emplacement
recommand6 de
ralimentatbn Du
de gaz _ d6coupage 6
la ligne
du centre
F51 ASSUREZ-VOUS OUE LES
REVF:TEMENTS MUR, LE
COMPTOIR ET LES ARMOIRES
AUTOUR DE LA TABLE DE
CUISSON PUISSENT SUPPORTER
LA CHALEUR (POUVANT
ATTEINDRE 93°C [200°F])
Les rev#tements de
mur, lesarmoires et
le comptoir doivent
pouvoir supporter
une chaleru pouvant
atteindre 93°C (200°F)
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
dans d''autres langues
- English: GE JGP633DET1BB Installation guide
Documents connexes
-
GE JGP975BEKBB Guide d'installation
-
GE Profile Series JGP329SETSS Guide d'installation
-
-
GE Profile Series JGP970SEKSS Guide d'installation
-
-
-
-
GE PGP953DET5WW Guide d'installation
-
-