Wattstopper
®
Low Voltage Card Key Switch
Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
No: 24777 – 09/16 rev. 1
Catalog Number • Numéro de Catalogue • Número de Catálogo: HS-100
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
SPECIFICATIONS
Voltage ................................................................ 24VDC/24VAC (Class 2)
Current Consumption
DC ................................................................................... Max. 25mA
AC .................................................................................... Max. 90mA
Outputs ......................... Isolated relay (N.O./N.C.), 1A/30VDC/VAC SPDT
Egress Time Delay ................................................................... 30 seconds
Environment .......................................................................Indoor use only
Operating Temperature .............................. 32° to 104°F (0° to 40°C)
Humidity .................................................... 95% RH, non-condensing
Card Slot accepts standard size hotel card keys with dimensions
.............................................................2.125”W x 3.375”H x 0.034”D
.............................................. (53.975mm x 85.725mm x 0.8636mm)
Tools Needed
Insulated Screwdriver
Wire Strippers
DESCRIPTION AND OPERATION
The HS-100 is a low voltage card key switch that enables or disables power to electric circuits and loads in a hotel guest room or similar
site. When a hotel door entry card key (or the key fob HS-FOB) is inserted in the HS-100 card slot the controlled circuits are energized.
When the hotel door entry card key (or HS-FOB) is removed, the controlled circuits will remain energized for 30 seconds more to allow
safe egress from the hotel room. After this time delay elapses, they will be de-energized. To restore power to the room (that is, to the
controlled circuits and loads), the occupant will need to reinsert the hotel door entry card key into the HS-100 card slot.
Lighted Card Slot
To help you locate the HS-100 in a dark room, two green LEDs illuminate the card slot where the hotel door entry card key or the key
fob HS-FOB should be inserted. When the card or HS-FOB is in the slot, the green LEDs are OFF.
INSTALLATION AND WIRING
1. Make sure the insulation is stripped off the
wires to expose their copper cores to the length
indicated by the “Strip Gauge” shown in
Figure 1 (approx. 3/8”).
2. Insert wires into the terminals on the HS-100 as
indicated in these instructions for either power pack
wiring (Figure 2) or building control system wiring
(Figure 3). Make sure they are securely clamped.
3. Mount the HS-100 in the wall box with the mounting
screws provided.
4. Attach the cover plate then turn the power ON.
Power Pack Wiring:
1. Install the power pack according to its instructions.
2. Connect the power pack wires:
BLUE wire to isolated relay common (RLY COMM)
terminal on the HS-100.
RED wire (+24VDC) to the normally open relay
(N.O.) terminal and to the +24V IN terminal on the
HS-100. Building Control System Wiring:
WARNING: TURN THE POWER OFF AT THE
CIRCUIT BREAKER BEFORE WIRING.
Removing card key turns OFF power.
Insert card key for power.
Figure 1: Strip Gauge
Strip Gage
3/8"
9.66mm
Figure 2: Wiring to power pack
White (Neutral)
Red (Line)
White
Neutral
Black
Hot/Line
Power Pack
Blue
Black
Red *
(Load)
Local OFF
switches
08220r1
GROUND
LISTED
58GK
Photoelectric
Switc
h
58GK
hotoelectr
Switc
h
N.O.
COMM
+24V IN
N.C.
RLY COMM
Model #
HS-100
RLY COMM
COMM
Ground
N.O.
24V IN
Red
Controlled receptacles
inside the room
Lighting
load
Lighting
load
Lighting
load
Do not wire receptacles directly to HS-100; device is not rated to control receptacles.
*
Do not exceed the power pack’s maximum load rating.
C
Normally open
contactor
electrically held
120 VAC
Supply Circuits
Neutral
Neutral
Neutral
Neutral
Neutral
Neutral
HS-100
Card Key Switch
Card Key Switch
Input: 24VDC/24VAC Half Wave Rectified
Output: 1A/30V SPDT Isolated Relay
Indoor use only
800.879.8585
www.legrand.us/wattstopper
No. 24777 – 09/16 rev. 1
© Copyright 2016 Legrand All Rights Reserved.
© Copyright 2016 Tous droits réservés Legrand.
© Copyright 2016 Legrand Todos los derechos reservados.
Wattstopper warranties its products to be free
of defects in materials and workmanship for a
period of five (5) years. There are no obligations
or liabilities on the part of Wattstopper for
consequential damages arising out of, or in
connection with, the use or performance of this
product or other indirect damages with respect
to loss of property, revenue or profit, or cost of
removal, installation or reinstallation.
Wattstopper garantit que ses produits sont
exempts de défauts de matériaux et de fabrication
pour une période de cinq (5) ans. Wattstopper
ne peut être tenu responsable de tout dommage
consécutif causé par ou lié à l’utilisation ou
à la performance de ce produit ou tout autre
dommage indirect lié à la perte de propriété, de
revenus, ou de profits, ou aux coûts d’enlèvement,
d’installation ou de réinstallation.
Wattstopper garantiza que sus productos
están libres de defectos en materiales y mano
de obra por un período de cinco (5) años. No
existen obligaciones ni responsabilidades por
parte de Wattstopper por daños consecuentes
que se deriven o estén relacionados con el
uso o el rendimiento de este producto u otros
daños indirectos con respecto a la pérdida
de propiedad, renta o ganancias, o al costo
de extracción, instalación o reinstalación.
WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA
TROUBLESHOOTING
Lighted card slot is OFF; no response from controlled loads in the guest room when card is inserted in slot.
• Make sure the circuit breaker that feeds the controlled guest room loads is on and functioning.
• If the guest room loads are still not energized, turn power OFF and verify that the HS-100 is wired correctly and that all wires are
tightly secured inside the wiring terminals.
• If loads still do not respond properly after following troubleshooting, turn OFF power to the circuit and call Technical Support at
1.800.879.8585.
Lighted card slot is ON; no response from controlled loads in the guest room when card is inserted in slot or removed from it.
• If using a power pack, a direct connection between the Red (+24VDC) and the Blue thin wires on the power pack should close the
power pack’s relay and the controlled loads in the guest room should be energized.
• Turn power OFF, make this test connection and turn power back ON.
The controlled loads should be energized.
• If they are, turn power OFF and correctly rewire the HS-100, making sure that all wires are tightly secured inside the wiring
terminals.
If the controlled loads do not energize using the test connection, call Technical Support.
ORDERING INFORMATION
Catalog Number Description
HS-100 Low Voltage Card Key Switch; 24VDC/VAC
HS-150 Line Voltage Card Key Switch; 120/277VAC, 50/60Hz
HS-FOB* Key Fob accessory for use when room access uses a standard key entry or other system without standard size
hotel card key
HS-WP** Cover plate for single-gang box
HS-WPR Cover plate for triple-gang box with decorator switch option (card slot on the right)
HS-WPL Cover plate for triple-gang box with decorator switch option (card slot on the left)
Hotel Card Key Switches, Key Fobs and Cover Plates are available in White (-W), Light Almond (-LA), Ivory (-I), Black (-B), and Grey (-G)
* Not needed when hotel uses card key entry system.
** One HS-WP included with each switch.
Building Control System Wiring:
The HS-100’s Isolated Relay allows integration with a lighting control panel, a
building automation system (BAS), an energy management system (EMS), or
any other building control system that accepts a dry contact closure as an input
signal. Connect the wires coming from the building control system as follows:
• +24VDC or +24VAC Class 2 supply to the +24V IN terminal on the HS-100.
• Supply common to COMM terminal on the HS-100.
• Wire the Isolated Relay according to the building control system
requirements. The isolated relay is rated for 1A @ 30VAC/VDC:
▸ Normally Closed (N.C.) - Open when card key is in card slot.
▸ Normally Open (N.O.) - Closed when card key is in card slot.
▸ Isolated Relay Common (RLY COMM) must be used for proper operation.
08220r1
GROUND
Card Key Switch
Input: 24VDC/24VAC Half Wave Rectified
Output: 1A/30V SPDT Isolated Relay
Indoor use only
LISTED
58GK
Photoelectric
Switc
h
58GK
hotoelectr
Switc
h
N.O.
COMM
+24V IN
N.C.
RLY COMM
Model #
HS-100
RLY COMM
COMM
N.O.
+24V IN
N.C.
Lighting
control
panel
or other
building
control
system
Figure 3: Class 2 wiring to building control system
-
1
-
2
dans d''autres langues
- English: Legrand HS-150-W Installation guide
Documents connexes
-
wattstopper HS-WP-W Guide d'installation
-
-
-
-
-
Legrand UT-300-1-U Mode d'emploi
-
Legrand DT-300 Guide d'installation
-