GE Profile ETS22XBPCC Le manuel du propriétaire

ge.com
Refrigerators
Top-Freezer
200D8222P001     49-60446     11-05 JR
Safety Instructions
Connect Electricity  . . . . . . . . . . . . . . . .3
Extension Cords  . . . . . . . . . . . . . . . . . .2
Proper Disposal  . . . . . . . . . . . . . . . . . . .2
Safety Precautions  . . . . . . . . . . . . . . . . .2
Operating Instructions
Additional Features  . . . . . . . . . . . . . . . .9
Automatic Icemaker  . . . . . . . . . . . . . .10
Controls   . . . . . . . . . . . . . . . . . . . . . .4, 5
Crispers and Pans  . . . . . . . . . . . . . .9, 10
Shelves and Bins  . . . . . . . . . . . . . . . .7, 8
Water Dispenser  . . . . . . . . . . . . . . . . .11
Water Filter  . . . . . . . . . . . . . . . . . . . . . .6
Care and Cleaning  . . . . . . . . . . . . . .11
Replacing the Light Bulbs  . . . . . . . . .12
Installation Instructions
Preparing to Install 
the Refrigerator . . . . . . . . . . . . . . . . . .13
Reversing the Door Swing  . . . . . .18–22
Water Line Installation  . . . . . . . . .14–18
Troubleshooting Tips  . . . . . . . . .24–26
Normal Operating Sounds  . . . . . . . . .23
Consumer Support
Consumer Support . . . . . . . .Back Cover
Performance Data Sheet . . . . . . . . . . .27
State of California Water 
Treatment Device Certificate  . . . . . . .28
Warranty for Canadian Customers . . .29
Warranty for U.S. Customers  . . . . . . .30
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
Find these numbers on the gray label 
on the left side, near the top of the
refrigerator compartment.
Réfrigérateurs
Congélateur supérieur
Manuel d’utilisation 
et d’installation
La section française commence à la page 31
Refrigeradores
Congelador superior
Models  22, 25
Owner’s Manual &
Installation Instructions
Manual del propietario 
e instalación
La sección en español empieza en la página 63

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the

use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

2

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■ This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■ Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■ Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.

■

■ Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

■

■ In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating

element located on the bottom of the icemaker.

Do not place fingers or hands on the automatic

icemaking mechanism while the refrigerator

is plugged in.

■

■ Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small.

Be careful closing doors when children are

in the area.

■

■ Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

■

■ Setting the controls to the O (off) position does

not remove power to the light circuit. On some

models, only the refrigerator control has a

O (off) setting.

■

■ Do not refreeze frozen foods which have

thawed completely.

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not

problems of the past. Junked or abandoned

refrigerators are still dangerous…even if they

will sit for “just a few days.” If you are getting

rid of your old refrigerator, please follow the

instructions below to help prevent accidents.

Before You Throw Away Your Old

Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children

may not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an

old refrigeration product, check with the company

handling the disposal about what to do.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

3

ge.com

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For

personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall outlet

to minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by

a qualified electrician to make sure the outlet

is properly grounded.

If the outlet is a standard 2-prong outlet,

it is your personal responsibility and obligation

to have it replaced with a properly grounded

3-prong wall outlet.

The refrigerator should always be plugged into

its own individual electrical outlet which has

a voltage rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull

straight out from the outlet.

Repair or replace immediately all power cords

that have become frayed or otherwise damaged.

Do not use a cord that shows cracks or abrasion

damage along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

This feature allows you to lock the controls

so the settings cannot be changed.

To lock the controls:

Set the controls to the desired settings.

Press and hold the lock pad for

3 seconds.

When the controls are locked, the indicator

light will come on and the control settings

will not be displayed.

To unlock the controls:

Press and hold the lock pad for 3 seconds.

After unlocking the controls, the settings

will be displayed, the lock indicator light

will go out and the settings can be changed.

About the controls on the refrigerator.

The controls will look like one of the following:

Initially, set the refrigerator control at 5 and the freezer control at 5

and allow 12–24 hours for the temperature to stabilize.

Several adjustments may be required. Adjust the controls one

increment at a time, and allow 12 hours after each adjustment for

the refrigerator to reach the temperature you have set.

Setting the controls to 0 stops cooling in both the refrigerator and

freezer compartments but does not shut off electrical power to

the refrigerator. On some models, only the refrigerator control has

a 0 setting.

Touch pad controls

• Setting either control at 0 will automatically set the other control at 0.

The zeros will blink until you set the controls.

• If both controls are set at 0 and either COLDER pad is pressed, the

controls will automatically reset to 5.

Control settings will vary based on personal preferences, usage and

operating conditions and may require more than one adjustment.

Locking the Controls (on some models)

4

Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Troubleshooting Tips

Installation Instructions Safety InstructionsOperating Instructions

Troubleshooting Tips

Installation Instructions Safety InstructionsOperating Instructions

Consumer Support

ADJUST REFRIGERATOR TEMP

ADJUST FREEZER TEMP

ACTIVATE LOCK

IS COLDEST

9

IS COLDEST

9

HOLD

3 SECS

COLDER

WARMER

COLDER

WARMER

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions

Installation Instructions

5

About the temperature controls. ge.com

The temperature controls are preset in the factory at 37°F for the

refrigerator compartment and 0°F for the freezer compartment.

Allow 24 hours for the temperature to stabilize to the preset

recommended settings.

The temperature controls can display both the SET temperature

as well as the actual temperature in the refrigerator and freezer.

The actual temperature may vary slightly from the SET

temperature based on usage and operating environment.

Setting either or both controls to OFF stops cooling in both the

freezer and refrigerator compartments, but does not shut off

electrical power to the refrigerator.

NOTE: The refrigerator is shipped with protective film covering

the temperature controls. If this film was not removed during

installation, remove it now.

To change the temperature, press and release the

WARMER or COLDER pad. The SET light will come

on and the display will show the set temperature.

To change the temperature, tap either the

WARMER or COLDER pad until the desired

temperature is displayed. Refrigerator temperatures

can be adjusted between 34°F and 44°F and the

freezer temperatures can be adjusted between

–6°F and +6°F.

Once the desired temperature has been set,

the temperature display will return to the actual

refrigerator and freezer temperatures after 5

seconds. Several adjustments may be required.

Each time you adjust controls, allow 24 hours for the

refrigerator to reach the temperature you have set.

To turn the cooling system off, tap the WARMER pad

for either the refrigerator or the freezer until the

display shows OFF. To turn the unit back on, press the

COLDER pad for either the refrigerator or freezer.

The SET light will illuminate on the side you

selected. Then press the COLDER pad again (on the

side where the SET light is illuminated) and it will

go to the preset points of 0°F for the freezer and

37°F for the refrigerator. Setting either or both

controls to OFF stops cooling in both the freezer

and refrigerator compartments, but does not shut

off electrical power to the refrigerator.

This feature allows you to lock the controls

so the settings cannot be changed.

To lock the controls:

Set the controls to the desired settings.

Press and hold the lock pad for

3 seconds.

When the controls are locked, the indicator

light will come on and the control settings

will not be displayed.

To unlock the controls:

Press and hold the lock pad for 3 seconds.

After unlocking the controls, the settings

will be displayed, the lock indicator light

will go out and the settings can be changed.

Locking the Controls (on some models)

6

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Troubleshooting Tips

Installation Instructions Safety InstructionsOperating Instructions

Troubleshooting Tips

Installation Instructions Safety InstructionsOperating Instructions

About the water filter. (on some models)

Water Filter Cartridge

The water filter cartridge is located inside

the cartridge holder in the back upper right

corner of the refrigerator compartment.

NOTE: Some models ship with the filter

bypass plug in place of the filter cartridge.

The filter bypass plug needs to be removed

before the filter cartridge is installed. Keep

the filter bypass plug for future use.

When to Replace the Filter

The filter cartridge should be replaced

every six months or earlier if the flow of

water to the icemaker and dispenser

decreases.

Installing the Filter Cartridge

If you are replacing the cartridge,

first remove the old one. To open the

cartridge cover, push in where indicated

and the cover will drop down.

Remove the cartridge by slowly rotating

it to the left. A small amount of water

may drip down.

CAUTION:

If air has been

trapped in the system, the filter cartridge

may be ejected as it is removed. Use caution

when removing.

Mark your calendar to remind you to

replace the filter cartridge in six months.

Remove the protective foil from the end

of the cartridge.

Position the cartridge inside the

cartridge holder and slowly rotate the

cartridge to the right until it stops.

When the cartridge is properly installed,

you will feel it “click” as it locks into

place. The blade on the end of the

cartridge should be positioned

vertically. Do not overtighten.

Close the cartridge cover.

Run water from the dispenser for

3 minutes (about 1

1

⁄2 gallons) to clear

the system and prevent sputtering.

See To Use the Dispenser section.

NOTE: A newly-installed water filter cartridge

may cause water to spurt from the dispenser.

Filter Bypass Plug

You must use the filter bypass plug

when a replacement filter cartridge is not

available. The dispenser and the icemaker

will not operate without the filter or filter

bypass plug.

Replacement Filters

To order additional filter cartridges

in the United States, visit our Website, ge.com,

or call GE Parts and Accessories, 800.626.2002.

Filter Model GSWF

Suggested Retail Price $34.95 USD

Customers in Canada should consult

the yellow pages for the nearest Camco

Service Center.

7

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions

Installation Instructions

Rearranging the Shelves

To remove:

Tilt the shelf up at the front.

Lift the shelf up at the back and

bring the shelf out.

To replace:

While tilting the shelf up, insert the top

hook at the back of the shelf in a slot

on the track.

Lower the front of the shelf until the

bottom of the shelf locks into place.

Spillproof Shelves (on some models)

Spillproof shelves have special edges to

help prevent spills from dripping to lower

shelves. To remove or replace the shelves,

see Rearranging the Shelves.

About the shelves and bins. ge.com

Not all features are on all models.

Some models have wire shelves that

can be adjusted in the same manner.

To remove:

Lift up the left side of the shelf and

slide it left into the center of the shelf

supports.

Rotate the right side of the shelf up and

out of the shelf supports.

Shelves in the refrigerator and freezer compartments are adjustable.

Refrigerator Compartment

Freezer Compartment

To replace:

Holding the shelf diagonally, insert the

left end of the shelf into the center of

the shelf supports on the side wall at the

desired level.

Insert the right end of the shelf into the

shelf supports at the same level. Rest

each end of the shelf on the bottom of

the shelf supports.

NOTE: For models with an automatic icemaker,

the freezer shelf must be in the lower position

for the ice cube bucket to catch the cubes.

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Troubleshooting Tips

Installation Instructions Safety InstructionsOperating Instructions

Troubleshooting Tips

Installation Instructions Safety InstructionsOperating Instructions

8

About the shelves and bins (cont.).

Non-Adjustable Shelves on the Door

To remove: Lift the shelf straight up, then

pull out.

To replace: Engage the shelf in the molded

supports on the door and push down.

It will lock in place.

Adjustable Bins on the Door

Adjustable bins can easily be carried from

refrigerator to work area.

To remove: Lift bin straight up, then

pull out.

To replace or relocate: Engage the bin in the

molded supports of the door, and push in.

Bin will lock in place.

The snugger helps prevent tipping, spilling

or sliding of small items stored on the door

shelf. Grip the finger hold near the rear of

the snugger and move it to fit your needs.

Snugger

Freezer Tilt Out Bin (on some models)

Push the button as you tilt out the bin.

To remove: Hold the sides of the bin and

lift it straight up, then pull out.

To replace: Engage the ends of the bin in

the molded supports on the door and

push down. It will lock in place.

NOTE: Do not overload the bin.

Slide-Out Spillproof Shelf (on some models)

The slide-out spillproof shelf allows you

to reach items stored behind others. The

special edges are designed to help prevent

spills from dripping to lower shelves.

To remove:

Remove all items from shelf.

Slide the shelf out until it stops.

Lift the front edge of the shelf until the

central tabs are above the front bar.

Continue pulling the shelf forward

until it can be removed.

To replace:

Place the rear shelf tabs just in front of

the central notches on the shelf frame.

Slide the shelf in until the central tabs

are slightly behind the front bar.

Lower the shelf into place until it is

horizontal and slide the shelf in.

Make sure that the shelf sits flat after reinstallation

and doesn’t move freely from side to side.

Make sure you push the shelves all the way in

before you close the door.

Finger hold

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions

Installation Instructions

9

About the crispers and pans.

Not all features are on all models.

About the additional features. ge.com

Not all features are on all models.

Fruit and Vegetable Crisper

Excess water that may accumulate in the

bottom of the drawers or under the drawers

should be wiped dry.

Adjustable Humidity Crisper (on some models)

Slide the control all the way to the

HIGH setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the LOW

setting to provide lower humidity levels

recommended for most fruits.

Shelf Saver Rack (on some models)

Slide-out beverage rack holds 12 cans of

soda or 2 wine/water bottles (lengthwise).

It can be removed for cleaning.

To remove, slide the rack out to the stop

position, lift the rack up and past the stop

position and lift it out.

Snack Pan (on some models)

This pan can be moved to the most useful

location for your family’s needs.

To remove, slide the pan out to the stop

position, lift the pan up and past the stop

position and lift it out.

Adjustable Temperature Deli Pan (on some models)

When the pan is placed in the top 6 slots

on the left side and the lever is set at

COLDEST, air from the freezer is forced

around the pan to keep it very cold.

You can move the pan to any location if

you don’t want the extra cold storage.

The settings can be adjusted anywhere

between cold and coldest .

When set at cold, the pan will stay at the

normal refrigerator temperature.

The coldest setting provides the coldest

storage area.

10

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Troubleshooting Tips

Installation Instructions Safety InstructionsOperating Instructions

Troubleshooting Tips

Installation Instructions Safety InstructionsOperating Instructions

About crisper removal.

Not all features are on all models.

About the automatic icemaker.

A newly-installed refrigerator may take 12–24 hours to begin making ice.

Crisper Removal

To Remove:

These drawers can be removed easily by

lifting up slightly while pulling the drawer

past the stop location.

When the door cannot be fully opened,

remove the drawer farthest from the door

first. Make sure the drawer closest to the

door is fully closed. There is a latch at the

front of the center slide rail. Push down on

the latch and slide the center slide rail, to

which the drawer is attached, away from the

door. Remove the drawer.

Icemaker Accessory Kit

If your refrigerator did not come already

equipped with an automatic icemaker,

an icemaker accessory kit is available at

extra cost.

Check the back of the refrigerator for

the specific icemaker kit needed for

your model.

Automatic Icemaker (on some models)

The icemaker will produce seven or eight

cubes (depending on model) per cycle—

approximately 100–130 cubes in a 24-hour

period, depending on freezer compartment

temperature, room temperature, number

of door openings and other use conditions.

There are two types of icemakers: power

switch models and feeler arm models.

If the refrigerator is operated before the

water connection is made to the icemaker,

set the power switch to O (off) or move the

feeler arm to the STOP (up) position.

When the refrigerator has been connected

to the water supply, set the power switch to

the I (on) position or move the feeler arm to

the ON (down) position. On power switch

models, the green light will come on.

You will hear a buzzing sound each time

the icemaker fills with water.

The icemaker will fill with water when it

cools to approximately 15°F. A newly-

installed refrigerator may take 12 to 24

hours to begin making ice cubes.

Throw away the first few batches of ice to

allow the water line to clear.

Be sure nothing interferes with the sweep

of the feeler arm.

When the bin fills to the level of the feeler

arm, the icemaker will stop producing ice.

It is normal for several cubes to be joined

together.

If ice is not used frequently, old ice cubes

will become cloudy, taste stale and shrink.

On power switch models, the green power

light will blink if ice cubes get stuck in the

icemaker. To correct this, set the power

switch to O (off) and remove the cubes. Set

the power switch to I (on) to restart the

icemaker. After the icemaker has been

turned on again, there will be a delay of

about 45 minutes before the icemaker

resumes operation.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle multiple

times when making one batch of ice.

Icemaker

Feeler Arm

Power

Switch

Green

Power Light

Power switch model

Feeler Arm in

the STOP

(up) position

Feeler Arm in

the ON (down)

position

Feeler arm model

Preparing to Move

Secure all loose items such as base grille,

shelves and drawers by taping them securely

in place to prevent damage.

Be sure the refrigerator stays in an upright position

during moving.

For long vacations or absences, remove

food and unplug the refrigerator. Move

the freezer control to the O (off) position,

and clean the interior with a baking soda

solution of one tablespoon (15 ml) of

baking soda to one quart (1 liter) of water.

Leave the doors open.

Set the icemaker power switch to the O (off)

position and shut off the water supply to

the refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water

supply system (on some models) to prevent

serious property damage due to flooding.

11

About the water dispenser. (on some models) ge.com

Behind the Refrigerator

Be careful when moving the refrigerator

away from the wall. All types of floor

coverings can be damaged, particularly

cushioned coverings and those with

embossed surfaces.

Pull the refrigerator straight out and return

it to position by pushing it straight in.

Moving the refrigerator in a side direction

may result in damage to the floor covering

or refrigerator.

When pushing the refrigerator back, make sure you

don’t roll over the power cord or icemaker supply

line (on some models).

Preparing for Vacation

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Care and cleaning of the refrigerator.

Cleaning the Outside

The door handles and trim. Clean with

a cloth dampened with soapy water.

Dry with a soft cloth.

Keep the outside clean. Wipe with a clean

cloth lightly dampened with mild liquid

dish detergent. Dry with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish cloth

or wet towel. These may leave a residue that

can erode the paint. Do not use scouring pads,

powdered cleaners, bleach or cleaners containing

bleach because these products can scratch and

weaken the paint finish.

Cleaning the Inside

To help prevent odors, leave an open box of

baking soda in the refrigerator and freezer

compartments.

Unplug the refrigerator before cleaning.

If this is not practical, wring excess moisture

out of sponge or cloth when cleaning

around switches, lights or controls.

Use warm water and baking soda solution—

about a tablespoon (15 ml) of baking soda

to a quart (1 liter) of water. This both cleans

and neutralizes odors. Thoroughly rinse

and wipe dry.

Avoid cleaning cold glass shelves (on some models)

with hot water because the extreme temperature

difference may cause them to break. Handle glass

shelves carefully. Bumping tempered glass can

cause it to shatter.

Do not wash any refrigerator parts in the dishwasher.

Wash ice trays in lukewarm water only—do not put

them in an automatic dishwasher.

The water dispenser is located on the left

wall inside the refrigerator compartment.

To dispense water:

Hold the glass against the recess.

Push the water dispenser button.

Hold the glass underneath the

dispenser for 2–3 seconds after

releasing the dispenser button.

Water may continue to dispense

after the button is released.

If no water is dispensed when the refrigerator is first

installed, there may be air in the water line system.

Press the dispenser button for at least 2 minutes to

remove trapped air from the water line and to fill the

water system. During this process, the dispenser

noise may be loud as the air is purged from the

water line system. To flush out impurities in the

water line, throw away the first 6 glassfuls of water.

NOTE: To avoid water deposits, the dispenser

should be cleaned periodically by wiping with a

clean cloth or sponge.

12

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Troubleshooting Tips

Installation Instructions Safety InstructionsOperating Instructions

Troubleshooting Tips

Installation Instructions Safety InstructionsOperating Instructions

Replacing the light bulbs.

Turning the control to the O (off) position does not remove power to the light circuit.

Refrigerator Compartment

Freezer Compartment Light (on some models)

CAUTION: Light bulbs may be hot.

Unplug the refrigerator.

The bulb is located behind a light

shield at the back of the freezer

compartment. To remove, squeeze

the top and bottom of the shield and

pull the shield off.

After replacing with an appliance bulb

of the same or lower wattage, replace

the shield.

Plug the refrigerator back in.

CAUTION: Light bulbs may be hot.

Unplug the refrigerator.

The bulbs are located at the top of

the refrigerator compartment near

the opening. On some models, a light

shield will have to be removed.

To remove the light shield, grasp the

shield as shown. Squeeze the shield

and rotate the shield toward the back

of the refrigerator. The light shield

will pop out.

Replace the bulb with an appliance

bulb of the same or lower wattage.

On models with a light shield, replace

the light shield.

Plug the refrigerator back in.

Light shield

Freezer Compartment Dome Light (on some models)

CAUTION: Light bulbs may be hot.

Unplug the refrigerator.

The bulb is located at the top of the

freezer compartment inside the dome

light shield. To remove the shield, place

your finger in the pocket at the back

of the shield. Pull the shield forward

and down.

After replacing with an appliance

bulb of the same or lower wattage,

replace the shield.

Plug the refrigerator back in.

Pocket

13

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these

instructions for local inspector’s use.

•

IMPORTANT – Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions

for future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time – Refrigerator Installation

15 minutes

• Proper installation is the responsibility of

the installer.

• Product failure due to improper installation

is not covered under the Warranty.

• Do not install the refrigerator where the temperature

will go below 60°F (16°C) because it will not run often

enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature

will go above 100°F (37°C) because it will not perform

properly.

• Install it on a floor strong enough to support it fully

loaded.

REFRIGERATOR LOCATION

Installation

Refrigerator

Instructions

Models 22 and 25

Allow the following clearances for ease of installation,

proper air circulation and plumbing and electrical

connections:

• Sides 1/8″ (4 mm)

• Top 1″ (25 mm)

• Back 1″ (25 mm)

If the refrigerator is against a wall on either side, allow

a 1/8″ (3 mm) door clearance.

CLEARANCES

The rollers have 3 purposes:

■

Rollers adjust so the doors close on their own when

opened about 45°.

■

Rollers adjust so the refrigerator is firmly positioned

on the floor and does not wobble.

■

Rollers allow you to move the refrigerator away from

the wall for cleaning.

To adjust the rollers:

Remove the base grille by

positioning hands as shown.

Rotate the bottom of the

grille outward until the clips

snap out.

Pull the grille away from the

refrigerator.

Using a screwdriver, turn

the two front roller

adjusting screws clockwise

to raise the refrigerator,

counterclockwise to lower it.

Replace the grille so the

notch in the grille will fit

around the bottom door

hinge.

Tilt the top of the grille

toward the refrigerator and

insert the long metal clips

into the top of the oval

openings at the bottom of

the refrigerator.

Rotate the bottom of the

grille toward the refrigerator

until it snaps into place.

ROLLERS

If the refrigerator has an icemaker, it will have to be

connected to a cold water line. A GE water supply kit

(containing tubing, shutoff valve, fittings and

instructions) is available at extra cost from your dealer,

by visiting our Website at ge.com (in Canada at

www.geappliances.ca) or from Parts and Accessories,

800.626.2002 (in Canada 1.888.261.3055).

WATER SUPPLY TO THE ICEMAKER

(ON SOME MODELS)

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

In Canada, call 1.800.361.3400

or Visit our Website at: www.geappliances.ca

14

INSTALLING THE WATER LINE

(ON SOME MODELS)

Installation Instructions

Recommended copper water supply kits are WX8X2,

WX8X3 or WX8X4, depending on the amount of

tubing you need. Approved plastic water supply lines

are GE SmartConnect

™

Refrigerator Tubing

(WX08X10002, WX08X10006, WX08X10015 and

WX08X10025).

When connecting your refrigerator to a GE Reverse

Osmosis Water System, the only approved installation

is with a GE RVKit. For other reverse osmosis water

systems, follow the manufacturer’s recommendations.

This water line installation is not warranted by the

refrigerator or icemaker manufacturer. Follow these

instructions carefully to minimize the risk of expensive

water damage.

Water hammer (water banging in the pipes) in house

plumbing can cause damage to refrigerator parts and

lead to water leakage or flooding. Call a qualified

plumber to correct water hammer before installing

the water supply line to the refrigerator.

To prevent burns and product damage, do not hook

up the water line to the hot water line.

If you use your refrigerator before connecting the

water line, make sure the icemaker power switch is

in the O (off) position.

Do not install the icemaker tubing in areas where

temperatures fall below freezing.

When using any electrical device (such as a power

drill) during installation, be sure the device is double

insulated or grounded in a manner to prevent the

hazard of electric shock, or is battery powered.

All installations must be in accordance with local

plumbing code requirements.

BEFORE YOU BEGIN

• Copper or GE SmartConnect

™

Refrigerator Tubing

kit, 1/4″ outer diameter to connect the refrigerator

to the water supply. If using copper, be sure both ends

of the tubing are cut square.

To determine how much tubing you need: measure

the distance from the water valve on the back of the

refrigerator to the water supply pipe. Then add

8′ (2.4 m). Be sure there is sufficient extra tubing

(about 8′ [2.4 m] coiled into 3 turns of about

10″ [25 cm] diameter) to allow the refrigerator to

move out from the wall after installation.

GE SmartConnect

™

Refrigerator Tubing Kits are

available in the following lengths:

2′ (0.6 m) – WX08X10002

6′ (1.8 m) – WX08X10006

15′ (4.6 m) – WX08X10015

25′ (7.6 m) – WX08X10025

Be sure that the kit you select allows at least 8′ (2.4 m)

as described above.

NOTE: The only GE approved plastic tubing is that

supplied in GE SmartConnect

™

Refrigerator Tubing

kits. Do not use any other plastic water supply line

because the line is under pressure at all times. Certain

types of plastic will crack or rupture with age and cause

water damage to your home.

WHAT YOU WILL NEED

15

Installation Instructions

SHUT OFF THE MAIN WATER

SUPPLY

Turn on the nearest faucet long enough to clear

the line of water.

Install the shutoff valve on the nearest frequently used

drinking water line.

1

Choose a location for the valve that is easily

accessible. It is best to connect into the side of a

vertical water pipe. When it is necessary to connect

into a horizontal water pipe, make the connection

to the top or side, rather than at the bottom,

to avoid drawing off any sediment from the

water pipe.

CHOOSE THE VALVE LOCATION

2

Drill a 1/4″ hole in the water pipe (even if using a

self-piercing valve) using a sharp bit. Remove any

burrs resulting from drilling the hole in the pipe.

Take care not to allow water to drain into the drill.

Failure to drill a 1/4″ hole may result in reduced

ice production or smaller cubes.

DRILL THE HOLE FOR THE VALVE

3

• A GE water supply kit (containing tubing, shutoff

valve and fittings listed below) is available at extra

cost from your dealer or from Parts and Accessories,

800.626.2002.

• A cold water supply. The water pressure must be

between 20 and 120 p.s.i. (1.4–8.1 bar).

• Power drill.

• 1/2″ or adjustable wrench.

• Straight and Phillips blade screwdriver.

• Two 1/4″ outer diameter compression nuts and

2 ferrules (sleeves)—to connect the copper tubing

to the shutoff valve and the refrigerator water valve.

OR

• If you are using a GE SmartConnect

™

Refrigerator

Tubing kit, the necessary fittings are preassembled

to the tubing.

• If your existing copper water line has a flared fitting

at the end, you will need an adapter (available at

plumbing supply stores) to connect the water line to

the refrigerator OR you can cut off the flared fitting

with a tube cutter and then use a compression fitting.

Do not cut formed end from GE SmartConnect

™

Refrigerator tubing.

• Shutoff valve to connect to the cold water line.

The shutoff valve should have a water inlet with a

minimum inside diameter of 5/32″ at the point of

connection to the COLD WATER LINE. Saddle-type

shutoff valves are included in many water supply kits.

Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes.

WHAT YOU WILL NEED

(CONT.)

16

INSTALLING THE WATER LINE

(CONT.)

Place the compression nut and ferrule (sleeve)

for copper tubing onto the end of the tubing and

connect it to the shutoff valve.

Make sure the tubing is fully inserted into the valve.

Tighten the compression nut securely.

For plastic tubing from a GE SmartConnect

™

Refrigerator Tubing kit, insert the molded end

of the tubing into the shutoff valve and tighten

compression nut until it is hand tight, then tighten

one additional turn with a wrench. Overtightening

may cause leaks.

CONNECT THE TUBING

TO THE VALVE

7

Turn the main water supply on and flush out the

tubing until the water is clear.

Shut the water off at the water valve after about

one quart (1 liter) of water has been flushed

through the tubing.

FLUSH OUT THE TUBING

8

Installation Instructions

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

Saddle-Type

Shutoff Valve

Compression

Nut

SmartConnect

™

Tubing

Packing Nut

Outlet Valve

Ferrule (sleeve)

Fasten the shutoff valve to the cold water pipe with

the pipe clamp.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

FASTEN THE SHUTOFF VALVE

4

Tighten the clamp screws until the sealing washer

begins to swell.

NOTE: Do not overtighten or you may crush the

tubing.

TIGHTEN THE PIPE CLAMP

5

Vertical Cold

Water Pipe

Saddle-Type

Shutoff Valve

Washer

Inlet End

Pipe Clamp

Clamp Screw

Route the tubing between the cold water line and

the refrigerator.

Route the tubing through a hole drilled in the wall

or floor (behind the refrigerator or adjacent base

cabinet) as close to the wall as possible.

NOTE: Be sure there is sufficient extra tubing

(about 8 feet [244 cm] coiled into 3 turns of about

10″ [25 cm] diameter) to allow the refrigerator to

move out from the wall after installation.

ROUTE THE TUBING

6

Pipe Clamp

17

Tighten any connections that leak.

TURN THE WATER ON AT THE

SHUTOFF VALVE

10

Installation Instructions

Place the compression nut and ferrule (sleeve)

onto the end of the tubing as shown. On GE

SmartConnect

™

Refrigerator Tubing kit, the nuts

are already assembled to the tubing.

Insert the end of the tubing into the water valve

connection as far as possible. While holding the

tubing, tighten the fitting.

For plastic tubing from a GE SmartConnect

™

Refrigerator Tubing kit, insert the molded end of

the tubing into the shutoff valve and tighten

compression nut until it is hand tight, then tighten

one additional turn with a wrench. Overtightening

may cause leaks.

Remove the plastic flexible cap from the water valve

(refrigerator connection).

NOTES:

• Before making the connection to the refrigerator,

be sure the refrigerator power cord is not

plugged into the wall outlet.

• We recommend installing a water filter if your

water supply has sand or particles that could clog

the screen of the refrigerator’s water valve. Install

it in the water line near the refrigerator. If using

GE SmartConnect

™

Refrigerator Tubing kit, you

will need an additional tube (WX08X10002) to

connect the filter. Do not cut plastic tube to

install filter.

CONNECT THE TUBING TO THE

REFRIGERATOR

9

CONNECT THE TUBING TO THE

REFRIGERATOR

(CONT.)

9

Remove the access cover.

Reattach the access cover.

Fasten the tubing into the clamp provided to hold

it in a vertical position. You may need to pry open

the clamp.

1/4″ Compression Nut

Tubing Clamp

1/4″ Tubing

Ferrule (sleeve)

Refrigerator

Connection

SmartConnect

™

Tubing

One of the illustrations below will look like the

connection on your refrigerator.

Icemaker Models without Water Dispenser

1/4″ Tubing

Tubing Clamp

1/4″ Compression Nut

Ferrule (sleeve)

SmartConnect

™

Tubing

Refrigerator Connection

Water Dispenser Models

18

REVERSING THE DOOR SWING

Arrange the coil of tubing so that it does not vibrate

against the back of the refrigerator or against the

wall. Push the refrigerator back to the wall.

PLUG IN THE REFRIGERATOR

11

START THE ICEMAKER (CONT.)

Feeler arm models – Move the feeler arm to the

ON (down) position. The icemaker will not begin to

operate until it reaches its operating temperature

of (15 F) (-9 C) or below. It will begin operation

automatically if the icemaker feeler arm is in the

ON (down) position.

NOTE: In lower water pressure conditions, the

water valve may turn on up to 3 times to deliver

enough water to the icemaker.

INSTALLING THE WATER LINE

(CONT.)

Installation Instructions

TOOLS YOU WILL NEED

5/16″ Head socket driver

3/4″ Head socket driver

(a 6-point socket is

recommended)

Phillips screwdriver

Putty knife or

thin-blade screwdriver

Masking tape

IMPORTANT NOTES

When reversing the door swing:

• Read the instructions all the way through before

starting.

• Handle parts carefully to avoid scratching paint.

• Set screws down by their related parts to avoid using

them in the wrong places.

• Provide a non-scratching work surface for the doors.

IMPORTANT: Once you begin, do not move the

cabinet until door-swing reversal is completed.

These instructions are for changing the hinges from

the right side to the left side—if you ever want to change

the hinges back to the right side, follow these same

instructions and reverse all references to left and right.

Unplug the refrigerator from its electrical outlet.

Empty all door shelves, including the dairy

compartment.

Feeler Arm in the

STOP (up) position

Feeler Arm in the ON

(down) position

Feeler arm model

START THE ICEMAKER

Power switch models – Set the icemaker power

switch to the I (on) position. The icemaker will

not begin to operate until it reaches its operating

temperature of 15°F (–9°C) or below. It will then

begin operation automatically if the icemaker

power switch is in the I (on) position, and the

green light will come on.

Icemaker

Feeler Arm

Power

Switch

Green Power

Light

Power switch model

19

Installation Instructions

REMOVE THE REFRIGERATOR

DOOR

2

Tape the door shut with masking tape.

Remove the center hinge pin with a 3/4″ socket.

CAUTION: Do not let door drop to the floor.

To do so could damage the door stop.

Remove the tape and tilt the door away from the

cabinet. Lift the door straight off the bottom hinge

bracket.

Set the door on a non-scratching surface, with the

inside up.

TRANSFER TOP HINGE TO

THE LEFT

Interchange hinge and screws at top right with screws

at the top left of cabinet.

Do not tighten screws on hinge side at this time.

3

Hinge Pin

REMOVE THE FREEZER DOOR

1

Tape the door shut with masking tape.

Remove the tape and tilt the door away from the

cabinet. Lift it off the center hinge pin.

Set the door on a non-scratching surface with

the inside up.

Remove the hinge cover on top of the freezer door

(on some models).

Remove the two screws, then lift the hinge straight

up to free the hinge pin from the socket in the top

of the door.

Top Hinge

TRANSFER BOTTOM HINGE

BRACKET TO THE LEFT

Remove the base grille by pulling it straight out.

Using a socket driver, move the bottom hinge bracket

from the right side to the left side.

NOTE: If the washer is not on the hinge bracket,

check to see if it is stuck to the bottom of the door.

4

20

TRANSFER REFRIGERATOR

DOOR HANDLE TO THE RIGHT

To remove the handle: Remove the plug button by

carefully prying under the edge with a putty knife.

Remove the exposed screw holding the handle.

7

Remove the two screws holding the handle to the

top of the door.

After removing the handle: Move the small plug

buttons from the top right side of the door top and

insert them into the holes on the opposite side.

Small Plug

Buttons

Move the large plug button from the left edge of the

door and insert it into the hole on the opposite side.

Plug Button

Handle

Plug

Handle

Plug

Hole

Handle Plug

Short

Screw

Short Handle

Long Handle

REVERSING THE DOOR SWING (CONT.)

Installation Instructions

TRANSFER CENTER HINGE

BRACKET TO THE LEFT

Remove the center hinge bracket by removing

the three screws.

NOTE: Keep these screws with the hinge bracket.

They are long screws and will be used when installing

the hinge on the other side.

You will need to remove the color-matched cap from

the screw head before you can remove the screw.

Use the edge of a thin flat blade to gently pry the

caps off the screw heads. (A putty knife works well

for this.) Cover the blade with tape to prevent

scratching the paint.

Remove the mullion cover from the left side using

the thin flat blade. Assemble it to the right side.

Remove the screw from the center left side of the

cabinet. Screw it into the holes on the right side.

Place the center hinge bracket over the holes at

the center left side of the cabinet. Insert and

tighten the three long screws.

Replace the cap by snapping it over the screw with

your finger.

5

TRANSFER DOOR STOPS

On each door, move the metal door stop from the

right to the left.

Move any screws from the left to the right.

6

Screw Cap

Mullion Cover

La page charge ...

GE Profile ETS22XBPCC Le manuel du propriétaire

GE Profile ETS22XBPCC Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents