Faber Scirocco Lux 36 BK Guide d'installation

SCLX3015BKNB-B

SCLX3615BKNB-B

SCLX3015SSNB-B

SCLX3615SSNB-B

Installation Instructions

Use and Care Information

Instructions d'installation

Utilisez et d'entretien

SCIROCCO LUX

2

READ AND SAVE THESE INSTRUCTIONS BEFORE YOU

START INSTALLING THIS RANGEHOOD

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium setting.

b)AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan

orlter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A

RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

a)SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnofftheburner.

BECAREFULTOPREVENTBURNS.IftheamesdonotgooutimmediatelyEVACUATE

AND CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will

result.

d) Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. Thereissmallandcontainedintheareawhereitstarted.

3. Theredepartmentisbeingcalled.

4. Youcanghttherewithyourbacktoanexit.

* Based on "Kitchen Firesafety Tips" published by NFPA

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this fan

with any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have any

questions, contact the manufacturer.

2. Before servicing or cleaning unit, switch power off at service panel and lock the

service disconnecting means to prevent power from being switched on acciden-

tally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or

Explosive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. InstallationWorkAndElectricalWiringMustBeDoneByQualiedPerson(s)InAccor-

dance With All Applicable Codes And Standards, Including Fire-Rated Construction.

2. Sufcient airisneededfor propercombustion andexhausting ofgases through

theue(chimney) offuelburningequipmenttopreventbackdrafting.Followthe

heating equipment manufacturer's guideline and safety standards such as those

publishedbytheNational Fire ProtectionAssociation (NFPA),and theAmerican

SocietyforHeating,RefrigerationandAirConditioningEngineers(ASHRAE),and

the local code authorities.

3

ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED

MUST BE SEALED.

This rangehood requires at least 24" of clearance between the bottom of the rangehood

and the cooking surface or countertop. This hood has been approved by UL at this distance

from the cooktop.

This minimum clearance may be higher depending on local building codes. For gas cooktops

and combination ranges, a minimum of 30" is recommended and may be required.

Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking

surface or countertop. Consult the cooktop or range installation instructions given by the

manufacturer before making any cutouts.

MOBILE HOME INSTALLATION The installation of this rangehood must conform to the

Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly

Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280). See

Electrical Requirements.

• Venting system MUST terminate outside the home.

• DO NOT terminate the ductwork in an attic or other enclosed space.

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the ow of combustion and ventilation air.

• Failure to follow venting requirements may result in a re.

WARNING

!

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either through

the wall or the oor.

The length of the ductwork and the number of elbows should be kept to a minimum to provide ef-

cient performance. The size of the ductwork should be uniform. Do not install two elbows together.

Use duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or oor

opening around the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air

turbulence that greatly reduces performance.

Make sure there is proper clearance within the wall or oor for exhaust duct before making cutouts.

Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a support-

ing frame must be constructed.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

CAUTION-Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside–Do

not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and

other hidden utilities.

4. Ducted fans must always be vented to the outdoors.

4

• Electrical ground is required on this rangehood.

• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO

NOT use for grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or

grounding circuit could result in electrical shock.

• Check with a qualied electrician if you are in doubt as to whether the rangehood is

properly grounded.

• Failure to follow electrical requirements may result in a re.

WARNING

!

State of California Proposition 65 Warning (US only)

WARNING

This product contains chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

5

RANGEHOOD DIMENSIONS

3

11/16

“

25

1/4

“ - 31

1/4

”

4

3/4

“

3/16

“

16“

27

7/16

“

1/4

“

4“

9

13/16

“

13

1/16

“

25

9/16

“ - 31

9/16

“

13

1/16

“

30” - 36”

6

MAIN PARTS

Components

Ref. Qty. Product Components

1 1 Hood Canopy complete with:

Controls, Light, Filters.

3 1 Electric unit.

4 1 Top Frame

6 1 Duct Collar 10" duct collar used

with Remote Blowers

Ref. Qty. Installation Components

7.1 2 Lower Fixing Bracket

7.2 2 Top Side Fixing Bracket

7.3 2 Top Front Bracket

12a 16 Screws 1/8" x 3/8"

12b 6 Screws 3/16" x 5/16"

12c 8 Screws 3/16" x 9/16"

Qty. Documentation

1 Instruction Manual

10" duct collar used with Remote Blowers

AvailableAccessories(Purchasedseparately)

Recirculation Kit - sku # DUCTSCIR

Recirculation Vent Kit - Activated Charcoal Filter - FILTERSCIR

Internal Blower model - IBDD600-B

Remote Blower model - RB900, RB1200 (WIREBOX for Remote Blower included)

Wireless Remote Control - REMCTRL

Wiring box for Remote Blower - WIREBOXSCLX

Parts needed

- 6" Round Metal ductwork .



5



12b

7

EN

2

24









Inserting the Hood Canopy into the support surface from below

• Insert the Hood Canopy from below into the

support worktop, drilled as described above.

• With the aid of a support, lift the Hood Cano-

py until the front comes out of the Worktop.

• Insert the Brackets 7.2, as indicated in the

figure, into the slots provided and fix them

with the screws 12a provided.

• Centre the Hood Canopy with respect to the

Cooking Hob slot.

• Using the 2 screws 12c provided, fix the

Hood Canopy to the worktop and remove

the supports.

Warning:

If the cooker top is made from a material that does not allow the screws 12c to be inserted, use

a small amount of silicone to glue the Brackets 7.2 to the top and allow it to dry completely

before proceeding with installation.

1

2

The distance between the opening made for the cooker hob and the one for the suction device must

be minimum 1 3/16" - maximum 1 15/16", according to the strength of the material used for the top.

• Insert the Hood Canopy from below into the countertop

cutout, drilled as described above.

Installation Instructions

Cutout Dimensions

EN

2

23

INSTALLATION

This Hood is set up to be fitted inside the kitchen unit in:

• Ducting version: Evacuation to the outside.

Sequence of operations - Installation

• Drilling the Support Surface and Fitting the Hood

• Connections

• Functional Check

• Disposal of Packaging

Drilling the Support Surface

X

812

Warning

Once the Support surface has been drilled the Hood Canopy can be installed in two ways:

• By inserting the Hood Canopy from below ( X = 106 mm ).

• By inserting the Hood Canopy from above ( X = 113 mm ).

IMPORTANT

The minimum distance between the opening for the hob and the one for the hood must be of at

least 3-5 cm according to the strength of the material used for the working top.

Y

X

Inserting the Hood Canopy into the countertop from below

• Insert the Brackets

7.2, as indicated in

the gure, into the

slots provided and x

them with the screws

12a provided.

• Center the Hood

Canopy with respect

to the Cooktop slot.

• Using the 2 screws 12c provided, secure the

Hood Canopy to the countertop and remove

the supports.

Warning:

If the countertop is made from a material that does not allow the screws 12c to be inserted, use

a small amount of silicone to glue the Brackets 7.2 to the top and allow it to dry completely

before proceeding with installation.

• With the aid of a support,

lift the Hood Canopy until

the front comes out of the

countertop.

FOR YOUR SAFETY:

WARNING Before beginning the installation, switch power off at service panel and lock the service

disconnecting means to prevent power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Hood X Y

30" 25 15/16" 4 5/16"

36" 31 15/16" 4 5/16"

8

EN

2

26

12c

12a

7.1

12a

7.1

Fixing the Lower Brackets

• Screw the brackets 7.1 to the front of the Hood Canopy using the screws 12a provided.

• Before tightening the Brackets completely, make all the adjustments to allow them to rest on

the lower base of the worktop to avoid deformation of the upper brackets 7.2 as shown in the

figure.

• With the aid of a spirit level, set the Hood Canopy level vertically and fix it to the Lower

Surface using 2 screws 12c provided.

• Tighten the screws 12a completely.

3

• Insert the Brackets 7.2, as

indicated in the gure, into

the slots provided and x them

with the screws 12a provided.

Inserting the Hood Canopy into the countertop from above

• Insert the Hood Canopy into the

countertop, drilled as described

above.

• Center the Hood Canopy with

respect to the cooktop slot.

• Secure the Hood Canopy with

the 2 screws 12c provided.

Warning:

If the countertop is made from a material that does not allow the screws 12c to be inserted,

use a small amount of silicone to glue the Brackets 7.2 to the top and allow it to dry completely

before proceeding with installation.

EN

2

25









Inserting the Hood Canopy into the support surface from above

• Insert the Brackets 7.2, as

indicated in the figure, into the

slots provided and fix them with

the screws 12a provided.

• Insert the Hood Canopy into the

cooker top, drilled as described

above.

• Centre the Hood Canopy with

respect to the Cooking Hob slot.

• Fix the Hood Canopy with the 2

screws 12c provided.

Warning:

If the cooker top is made from a material that does not allow the screws 12c to be inserted, use

a small amount of silicone to glue the Brackets 7.2 to the top and allow it to dry completely

before proceeding with installation.

EN

2

25









Inserting the Hood Canopy into the support surface from above

• Insert the Brackets 7.2, as

indicated in the figure, into the

slots provided and fix them with

the screws 12a provided.

• Insert the Hood Canopy into the

cooker top, drilled as described

above.

• Centre the Hood Canopy with

respect to the Cooking Hob slot.

• Fix the Hood Canopy with the 2

screws 12c provided.

Warning:

If the cooker top is made from a material that does not allow the screws 12c to be inserted, use

a small amount of silicone to glue the Brackets 7.2 to the top and allow it to dry completely

before proceeding with installation.

4

Securing the Lower Brackets

• Screw the brackets 7.1 to the front of the Hood Canopy using the screws 12a provided.

• Before tightening the Brackets completely, make all the adjustments to allow them to rest on

the lower base of the Cabinet Base to avoid deformation of the upper brackets 7.2 as shown

in the gure.

9

EN

2

26

12c

12a

7.1

12a

7.1

Fixing the Lower Brackets

• Screw the brackets 7.1 to the front of the Hood Canopy using the screws 12a provided.

• Before tightening the Brackets completely, make all the adjustments to allow them to rest on

the lower base of the worktop to avoid deformation of the upper brackets 7.2 as shown in the

figure.

• With the aid of a spirit level, set the Hood Canopy level vertically and fix it to the Lower

Surface using 2 screws 12c provided.

• Tighten the screws 12a completely.

5

Leveling and Securing the Lower Brackets

• With the aid of a level,

set the Hood Canopy

level vertically and

secure it to the Lower

Surface using 2 screws

12c provided.

• Tighten the screws 12a

completely.

6

Securing the Squaring Brackets

• Screw the brackets 7.3 to the Hood Canopy using the screws 12b provided, without

tightening completely.

• Using the screws 12c provided, fasten the other part of the brackets 7.3 either to the side

walls of the unit or to the lower part of the cooktop.

EN

2

27

Fixing the Squaring Brackets

• Screw the brackets 7.3 to the Hood Canopy using the screws 12b provided, without

tightening completely.

• Using the screws 12c provided, fasten the other part of the brackets 7.3 either to the side

walls of the unit or to the lower part of the cooker top.

12b

7.3

12b

7.3

12c

• Tighten the screws 12c and 12b completely.

10

7a

Internal Blower Installation

• Installation of the Internal Blower (1) at the front or rear must

be decided according to the position of the cooktop, making

sure that the plug is properly positioned.

• The Internal Blower can be rotated as shown in the

gure 2 for multiple venting directions..

• Screw the Internal Blower to the Hood

Canopy using the screws 12a and 12b

provided as shown in the gure.

3

CAUTION - To Reduce The Risk Of Fire And Electric Shock, Install This Down Draft Only With

Integral Blowers IBDD600-B Manufactured by Faber.

11

3

• Connect the Wire Connector from the Blower with the

correct connector on the Electric Unit.

• Secure the Wire Connector from the Blower at the

Electric Unit with 2 screws.

3

12

7b

Connect the Remote Blower wiring to the connector of the Electric Unit.

Accessories needed:

- Remote Blower model - RB900, RB1200 (purchased separately).

- WIREBOXSCLX for Remote Blower (purchased separately).

Attention: Install the Wiring Box with two screws (provided) on a at and dry surface.

Connect the Remote Blower wiring plug connector to the connector of the Electric Unit.

Run 2-wire plus ground power cable from the Remote Blower to wiring box on the Cover according to

local codes and ordinances. Use Listed ttings.

Installation of Remote Blower

CAUTION - To Reduce The Risk Of Fire And Electric Shock, Install This Down Draft Only With Remote

Blowers RB900, RB1200 Manufactured by Faber.

4x

3

• Connect the Wire Connector

from the Blower with the

correct connector on the

Electric Unit.

• Secure the Wire

Connector from the

Blower at the Electric

Unit with 2 screws.

3

13

Installation of wiring connection

Remove the wiring electrical knockout using a at-blade

screwdriver. Feed the Power Supply Cable through the

electrical knockout.

Connect the Power Supply Cable to the Remote Blower.

Attach the White lead of the power supply (A) to the

White lead of the rangehood (D) with a twist-on type wire

connector. Attach the Black lead of the power supply to

the Black lead of the rangehood (B) with a twist-on type

wire connector (C). Connect the Green (E) (Green and

Yellow) ground wire under the Green grounding screws.

Replace the eld wiring compartment cover

Connect the ductwork to the damper and seal all connections with duct tape.

Turn the power supply on. Turn on the blower and light. If the rangehood does not operate, check that

the circuit breaker is not tripped or the house fuse blown. If the unit still does not operate, disconnect

the power supply and check that the wiring connections have been made properly.

Hood

wiring

A

E

D

B

C

14

8

EN

2

28

Fixing the Electric Unit

• Connect the wires coming out of the bottom

right part of the Hood Canopy to the

corresponding connector on the Electric

Unit, taking care not to make any wrong

connections.

• Fix the Electric Unit to the Hood Canopy

using the screws 12a provided.

• The position indicated in the figure is only

an option, as if necessary it may also be

fitted on the left of the Hood Canopy or

even left free on the base of the unit if there

are no structural or safety problems

involved.

Warning..: Do not install the product in such a way that the wiring box is in contact with the

floor.

• Connect the wires coming out of the bottom right part

of the Hood Canopy to the corresponding connector

on the Electric Unit, taking care not to make any

wrong connections. Check the picture below.

• Secure the Electric Unit to the Hood Canopy using the

screws 12a provided.

• The Electric Unit can be installed on the left or right of the

front of the hood canopy as shown above. It can also be

installed on the cabinet base if space allows.

EN

2

28

Fixing the Electric Unit

• Connect the wires coming out of the bottom

right part of the Hood Canopy to the

corresponding connector on the Electric

Unit, taking care not to make any wrong

connections.

• Fix the Electric Unit to the Hood Canopy

using the screws 12a provided.

• The position indicated in the figure is only

an option, as if necessary it may also be

fitted on the left of the Hood Canopy or

even left free on the base of the unit if there

are no structural or safety problems

involved.

Warning..: Do not install the product in such a way that the wiring box is in contact with the

floor.

"GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces

the risk of electric shock by providing an escape wire for the electric current. This appliance is

equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged

into an outlet that is properly installed and grounded.

WARNING - Improper grounding can result in a risk of electric shock.

Consult a qualied electrician if the grounding instructions are not completely understood, or if

doubt exists as to whether the appliance is properly grounded.

Do not use an extension cord. If the power supply cord is too short, have a qualied electrician

install an outlet near the appliance."

Warning..: Do not install the product in such a way that the electric unit is in contact with the oor.

Installation of Electrical Module

Connect the ductwork to the damper and seal all connections with duct tape.

Turn the power supply on. Turn on the blower and light. If the rangehood does not operate, check that

the circuit breaker is not tripped or the house fuse blown. If the unit still does not operate, disconnect

the power supply and check that the wiring connections have been made properly.

Power supply

Blower Connector

Command Flat

Connector

9 poles System

Connector

15

Connection the Air outlet with the

Accessories Remote

Motor

To connect the Hood to the outlet pipe, select the version that applies.

EN

2

29

Connection to the Air outlet

To connect the Hood to the outlet pipe, select the ver-

sion that applies.

Standard Outlets

According to your decision (Right or Left), break the

outlet hole already marked and screw on Flange 2 using

the 4 screws 12a provided.

Optional Outlets

The Hood is fitted with three other possible outlets:

Right Side

Left Side

Bottom

According to your decision, unfasten the screws fixing

the cover and fit a connector, not provided, to the outlet

(the connector shown in the figure is merely an

example).

1 1

22

30mm

220mm

55mm

1

3/16

"

Standard Outlets

According to your venting direction (Front or Rear), break off the outlet hole already marked

and screw on callout number from Main Parts Component using the 4 screws 12a provided.

10"

16

EN

3

31

Warning..:

Handle

with care

Fitting the Front element

• Lift the mobile hood canopy

(see paragraph on Use) by just a

few centimeters.

• To stop movement, simply

press down on the mobile

canopy as it lifts up.

Warning: Never block the

sliding door when it is opening

or closing, except during the

operations required to fit the

frame.

• Remove the sponge guards

from the corners of the glass.

• Take the front Frame and insert

it from above, making sure that

its tabs insert into the slots

provided on the Hood and

sliding it to the left.

Warning..: All the tabs must

be inserted.

• Use a tool (hammer) to tap all

along the front Frame from

right to left until it is

completely flush.

A piece of wood or similar

element can be inserted

between the hammer and the

front Frame to prevent any

damage.

• Please refer to the paragraph on

Use for indications of how to

return the mobile canopy to the

Standard position.

9

Installation of Top Frame

• Raise the downdraft to the Upper Position by a 1-2"

(See Page 15 for Use of Controls).

• Remove the sponge guards from the corners of the

glass.

• Take the Top Frame and insert it from above, making

sure that its tabs insert into the slots provided on the

downdraft and sliding it to the left.

Warning..: All the tabs must be inserted.

• Use a soft rubber mallet or similar tool to tap all

along the Top Frame from right to left until it is

completely ush.

A piece of wood or rubber block can be inserted

between the hammer and the front Frame to prevent

any damage.

• Please refer to the paragraph on Use for indications

of how to return the downdraft to the Standard

position.

10

Front Cover Panel

EN

3

32

Surround Suction Panel

• Open the Hood Door (see

USE).

• Remove the 2 strips of adhesive

tape fastening the panel during

transport.

• Raise the telescopic part to the Upper Position

(See Page 15 for Use of Controls).

• Remove the 2 strips of adhesive tape

fastening the panel during transport.

17

USE AND CARE INFORMATION

EN

3

33

USE

Control panel

Butto

n

Functio

n

o t t u b DEL

n

A

The button only works when the downdraft is open.

Press Briefly = Turns the Lights On/Off at maximum intensity.

Press and hold for 2 Seconds = Turns the Dimmer Lights

On/Off.

B Only works with the downdraft Open.

Press briefly = Activates/Deactivates Delay mode, causing auto-

matic shutdown of the Motor and the Lighting system from any

speed with a 15’ delay. It is disabled by pressing the same button

again, turning the motor off or closing the downdraft.

LED Button B+ Button for the set Speed are lit.

Works both with the downdraft Up and Down.

Press and hold for 2 Seconds = With the filter alarm triggered the

Filter Alarm is Reset. These indications are only visible when the

motor is turned off.

LED button ON:

Indicates the need to wash the metal grease filters.

The alarm is triggered after the Hood has been in

operation for 100 working hours.

Flashing LED button:

Indicates the need to change the activated charcoal

filters, and also to wash the metal grease filters. The

alarm is triggered after

the Hood has been in

operation for 200 working hours.

Works both with downdraft Up and Down with Motor + Lights =

Off.

Press and hold for 4 Seconds = Enables/disables the Keyboard

lock.

All the LED buttons flash twice. During the Lock

the LED buttons light up in sequence.

C Only works with the downdraft Up.

Press briefly = Activates speed four.

LED button ON.

Only works with the downdraft Up.

Press and hold for 2 seconds = Enables/Disables the

Intensive

speed. This speed is timed to run for 6 minutes. At the end of this

time the system will return to the speed set previously.

It is disabled by pressing the same button again, turning the motor

off or closing the downdraft.

Flashing LED button.

D Only works with the downdraft Up.

Activates speed three.

LED button ON.

E Only works with the downdraft Up

Activates/Deactivates speed two.

LED button ON.

F Only works with the downdraft Up.

Press briefly = Activates/Deactivates speed one.

LED button NO.

downdraft Up and Down

Press and hold for 2 Seconds = Enables/Disables the Activated

Charcoal Filter Alarm with the Motor turned off and no Filter

Alarm triggered.

LED button B flashes twice = Activated Charcoal

filter Alarm Activated.

LED button B flashes once = Activated Charcoal

filter Alarm Deactivate

d

.

G

downdraft Up

Press briefly = Turns the Motor off.

LED b

u

tton goes out.

downdraft Up and Down

Press and hold for 2 Seconds with Motor and Lights Off =

Enables/Disables the Remote control.

LED button

G

+ F flashes twice = Remote control

Enabled.

LED button G + F flashes once = Remote control

Disabled.

H downdraft Up = Lower the downdraft + Lights and Motor Off

downdraft Down = Upper the downdraft + Lights and Motor On.

Warning: If the downdraft remains partially open for any reason,

press the Button to complete the opening or closing cycle.

EN

3

33

USE

Control panel

Butto

n

Functio

n

o t t u b DEL

n

A

The button only works when the downdraft is open.

Press Briefly = Turns the Lights On/Off at maximum intensity.

Press and hold for 2 Seconds = Turns the Dimmer Lights

On/Off.

B Only works with the downdraft Open.

Press briefly = Activates/Deactivates Delay mode, causing auto-

matic shutdown of the Motor and the Lighting system from any

speed with a 15’ delay. It is disabled by pressing the same button

again, turning the motor off or closing the downdraft.

LED Button B+ Button for the set Speed are lit.

Works both with the downdraft Up and Down.

Press and hold for 2 Seconds = With the filter alarm triggered the

Filter Alarm is Reset. These indications are only visible when the

motor is turned off.

LED button ON:

Indicates the need to wash the metal grease filters.

The alarm is triggered after the Hood has been in

operation for 100 working hours.

Flashing LED button:

Indicates the need to change the activated charcoal

filters, and also to wash the metal grease filters. The

alarm is triggered after

the Hood has been in

operation for 200 working hours.

Works both with downdraft Up and Down with Motor + Lights =

Off.

Press and hold for 4 Seconds = Enables/disables the Keyboard

lock.

All the LED buttons flash twice. During the Lock

the LED buttons light up in sequence.

C Only works with the downdraft Up.

Press briefly = Activates speed four.

LED button ON.

Only works with the downdraft Up.

Press and hold for 2 seconds = Enables/Disables the Intensive

speed. This speed is timed to run for 6 minutes. At the end of this

time the system will return to the speed set previously.

It is disabled by pressing the same button again, turning the motor

off or closing the downdraft.

Flashing LED button.

D Only works with the downdraft Up.

Activates speed three.

LED button ON.

E Only works with the downdraft Up

Activates/Deactivates speed two.

LED button ON.

F Only works with the downdraft Up.

Press briefly = Activates/Deactivates speed one.

LED button NO.

downdraft Up and Down

Press and hold for 2 Seconds = Enables/Disables the Activated

Charcoal Filter Alarm with the Motor turned off and no Filter

Alarm triggered.

LED button B flashes twice = Activated Charcoal

filter Alarm Activated.

LED button B flashes once = Activated Charcoal

filter Alarm Deactivate

d

.

G

downdraft Up

Press briefly = Turns the Motor off.

LED b

u

tton goes out.

downdraft Up and Down

Press and hold for 2 Seconds with Motor and Lights Off =

Enables/Disables the Remote control.

LED button

G

+ F flashes twice = Remote control

Enabled.

LED button G + F flashes once = Remote control

Disabled.

H downdraft Up = Lower the downdraft + Lights and Motor Off

downdraft Down = Upper the downdraft + Lights and Motor On.

Warning: If the downdraft remains partially open for any reason,

press the Button to complete the opening or closing cycle.

18

RemoteControl(PurchasedSeparately)

This appliance can be commanded using a remote

control, powered by a CR2032 type 3 V battery (not

supplied).

• Do not place the remote control near heat sources.

• Do not discard the batteries with normal waste, they

must be put into the specic containers.

Remote Control Panel

Warning..: The remote control receiver is deactivated when rst supplied. To activate it, see the

paragraph Use Function of Button G.

EN

3

34

REMOTE CONTROL (OPTIONAL)

The appliance can be controlled using a remote control

powered by a 1.5 V carbon-zinc alkaline batteries of the

standard LR03-AAA type (not included).

• Do not place the remote control near to heat sources.

• Used batteries must be disposed of in the proper

manner.

Remote control panel

Warning..: The remote control receiver is deactivated when first supplied. To activate it, see the

paragraph Use Function of Button G.

Motor

downdraft Down:

Opens the downdraft, turns the motor on at speed one and turns the lights on at

maximum intensity.

downdraft Up:

Brief pressure: Motor On / Off.

Pressed for 2 Seconds: Closes the downdraft and Motor + Lights = Off.

Only with downdraftUp

:

Decreases the working speed each time it is pressed.

Only with downdraft Up

:

Increases the working speed each time it is pressed.

Intensive

Only with downdraft Up

:

Activates the Intensive function.

Delay

Only with downdraft Up

:

Activates the Delay function.

Light

Only with downdraft Up

:

Brief pressure: Lights On / Off.

Pressed for 2 Seconds: Dimmer lights On / Off.

19

LED LIGHTING UNIT

• LED lights must be replaced by Faber factory

authorized service.

Cleaning the Front Cover Panels

• Open the Front Cover Panel by pulling it at the top.

• Disconnect the panel from the hood canopy.

• The panel must never be washed in the dishwa-

sher.

• Clean the outside with a damp cloth and neutral

detergent.

• Clean the inside using a damp cloth and neutral

detergent; do not use wet cloths or sponges, or jets

of water; do not use abrasive substances.

• On completing the operation hook the panel and

close it.

CleaningtheMetalgreaselters

These can also be washed in the dishwasher, and

need to be cleaned whenever button B lights up or

at least once every 2 months use, or more frequently

if use is particularly intensive.

Resetting the alarm signal

• Turn the Lights and the Motor off.

• Press and hold button B for 2 seconds.

Cleaning the Filters

• Raise the downdraft to the Up position (see USE).

• Pull forward on the top edge of the Front Cover

to pull down.

• Remove the Filters one at a time, pushing them

towards the back of the unit and at the same time

pulling downward.

• Wash the Filters without bending them, and leave

them to dry completely before replacing. (If the

surface of the lter changes color as time goes by,

this will have absolutely no effect on the efciency

of the lter itself) .

• Replace, taking care to ensure that the handle

faces forwards.

• Close the Front Cover panel.

20

Wiring Diagram

991.0476.101 H90-322

D003071_03

991.0476.101 H90-322

D003071_03

La page charge ...

Faber Scirocco Lux 36 BK Guide d'installation

Ce manuel convient également à

Faber Scirocco Lux 36 BK Guide d'installation

dans d''autres langues

Documents connexes

Autres documents