Whirlpool WDG 8640S EX Mode d'emploi

1

GB

English,1

GB

WASHER-DRYER

! This symbol reminds you to read this instruc-

tion manual.

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 6

Cutting off the water and electricity supplies

Cleaning the washer-dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and advice, 7

General safety

Disposal

Opening the porthole door manually

Description of the washer-dryer, 8-9

Control panel

Display

How to run a wash cycle or a drying cycle, 10

Wash cycles and options, 11

Table of programmes and wash cycles

Wash options

Detergents and laundry, 12

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Troubleshooting, 13

Service, 14

WDG 8640

Instructions for use

Português,29

PT

ES

Español,15

Français,43

F

AR

, 57

FA

,71

2

GB

Installation

! This instruction manual should be kept in a safe

place for future reference. If the washer-dryer is

sold, transferred or moved, make sure that the

instruction manual remains with the machine so

that the new owner is able to familiarise himself/

herself with its operation and features.

! Read these instructions carefully: they contain

vital information relating to the safe installation

and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washer-dryer from its packaging.

2. Make sure that the washer-dryer has not been

damaged during the transportation process. If it

has been damaged, contact the retailer and do not

proceed any further with the installation process.

3 . R e m o v e t h e 4

protective screws (used

during transportation)

and the rubber washer

with the corresponding

spacer, located on the

rear part of the appliance

(see figure).

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will

need them again if the washer-dryer needs to

be moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washer-dryer on a flat sturdy floor,

without resting it up against walls, furniture

cabinets or anything else.

2. If the floor is not

p e r f e c t l y l e v e l ,

c o m p e n s a t e f o r

any unevenness by

tightening or loosening

the adjustable front

feet (see figure); the

angle of inclination,

measured in relation to

the worktop, must not

exceed 2°.

Levelling the machine correctly will provide it with

stability, help to avoid vibrations and excessive

noise and prevent it from shifting while it is

operating. If it is placed on carpet or a rug, adjust

the feet in such a way as to allow a sufficient

ventilation space underneath the washer-dryer.

Connecting the electricity and

water supplies

Connecting the water inlet hose

1. Connect the inlet

hose by screwing it to

a cold water tap using

a 3/4 gas threaded

connection (see figure).

Before performing the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the inlet

hose to the washer-

dryer by screwing it

onto the corresponding

water inlet of the

appliance, which is

situated on the top

right-hand side of

the rear part of the

appliance (see figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the range of values indicated in the Technical

data table (see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

3

GB

65 - 100 cm

Connecting the drain hose

Connect the drain

hose, without bending

it, to a drainage duct or

a wall drain located at a

height between 65 and

100 cm from the floor;

alternatively, rest it on

the side of a washbasin

or bathtub, fastening

the duct supplied to

the tap (see figure).

The free end of the

hose should not be

underwater.

! We advise against the use of hose extensions;

if it is absolutely necessary, the extension must

have the same diameter as the original hose and

must not exceed 150 cm in length.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

• the socket is earthed and in compliance with

the applicable law;

• the socket is able to sustain the appliance’s

maximum power load indicated on the

Technical Data Plate fixed on the machine;

• the supply voltage is included within the values

indicated on the Technical Data Plate fixed on

the machine.

• the socket is compatible with the washing

machine’s plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp

fused plug it can be plugged into a 13 amp

socket for immediate use. Before using the

appliance please read the instructions below.

WARNING - THIS APPLIANCE MUST BE

EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be

used, and the fuse cover re-fitted. If the fuse

cover is lost, the plug must not be used until a

replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of

the correct colour as indicated by the coloured

marking or the colour that is embossed in words

on the base of the plug. Replacements can

be obtained directly from your nearest Service

Depot.

Removing the plug:

If your appliance has a non-rewireable moulded

plug and you should wish to re-route the mains

cable through partitions, units etc., please

ensure that either:

the plug is replaced by a fused 13 ampere

rewireable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13

amp cable outlet, controlled by a switch, (in

compliance with BS 5733) which is accessible

without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself,

you make the pins unusable so that it cannot be

accidentally inserted into a socket.

Instructions for connecting cable to an alternative

plug:

Important: the wires in the mains lead are

coloured in accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

4

GB

As the colours of the wires in the lead may

not correspond with the coloured markings

identifying the terminals in your plug, proceed

as follows:

Connect Green & Yellow wire to terminal marked

E or or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked L or

coloured Red.

Connect Blue wire to terminal marked N or

coloured Black.

If a 13 amp plug (BS 1363) is used it must be

fitted with a

13 amp fuse, either in the plug or adaptor or at

the distribution board.

If you are in any doubt regarding the electrical

supply to your machine, consult a qualified

electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN & YELLOW EARTH (E)

Disposing of the appliance:

When disposing of the appliance please remove

the plug by cutting the mains cable as close as

possible to the plug body and dispose of it as

described on the previous page.

! The washing machine should not be installed

in an outdoor environment, not even where

the area is sheltered, because it may be very

dangerous to leave it exposed to damp, rain

and thunderstorms.

! When the washing machine is installed, the

mains socket must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent

or dangerously compressed.

! The power supply cable must only be replaced

by an authorised serviceman.

Warning! The company denies all liability if and

when these norms are not respected.

The first wash cycle

Once the appliance has been installed, and

before you use it for the first time, run a wash

cycle with detergent and no laundry, using the

programme “Auto Clean” (see “Cleaning the

washing machine”).

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

5

GB

Technical data

Model

WDG 8640

Dimensions

width 59.5 cm

height 85 cm

depth 54 cm

Capacity

from 1 to 8 kg for the wash

programme

from 1 to 6 kg for the drying

programme

Electrical

connections

please refer to the technical

data plate fixed to the ma-

chine

Water con-

nections

maximum pressure 1 MPa

(10 bar)

minimum pressure 0.05

MPa (0.5 bar)

drum capacity 58 litres

Spin speed

up to 1400 rotations per

minute

Energy ra-

ted

programmes

according to

regulation

EN 50229

Wash: programme 4; tempera-

ture 60°C; using a load of 8 kg.

Drying: the smaller load must

be dried by selecting the “A1”

(IRON) dryness level. The load

must consist of 2 sheets, 1 pil-

lowcase and 1 hand towel;

the remainder of the load must

be dried by selecting the “A4”

(EXTRA) dryness level.

This appliance conforms to

the following EC Directives:

- 2004/108/EC (Electromagne-

tic Compatibility)

- 2006/95/EC (Low Voltage)

- 2012/19/EU - WEEE

6

GB

Care and maintenance

Cutting off the water and electricity

supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system inside

the washer-dryer and help to prevent leaks.

• Unplug the washer-dryer when cleaning it and

during all maintenance work.

Cleaning the washer-dryer

• The outer parts and rubber components

of the appliance can be cleaned using a

soft cloth soaked in lukewarm soapy

water. Do not use solvents or abrasives.

• The washer-dryer has a “Auto Clean”

programme for its internal parts that must be

run with no load in the drum.

To help the wash cycle you may want to use

either the detergent (i.e. a quantity 10% the

quantity specified for lightly-soiled garments)

or special additives to clean the washer-dryer.

We recommend running a cleaning programme

every 40 wash cycles.

To start the programme press button A for 5

seconds (see figure).

The programme will start automatically and will

run for about 70 minutes. To stop the cycle press

the START/PAUSE button.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pulling

it out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of

your appliance

• Always leave the porthole door ajar in order to

prevent unpleasant odours from forming.

Cleaning the pump

The washer-dryer is fitted with a self-cleaning

pump which does not require any maintenance.

Sometimes, small items (such as coins or buttons)

may fall into the pre-chamber which protects the

pump, situated in its bottom part.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front part

of the washer-dryer

(see figure);

2. unscrew the lid

by rotating it anti-

clockwise (see figure):

a little water may trickle

out. This is perfectly

normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks

are securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose could

easily split open.

! Never use second-hand hoses.

1

2

A

7

GB

Precautions and tips

! This washer-dryer was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons and must

therefore be read carefully.

General safety

• This appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack

of experience and knowledge if they have been

given supervision or instruction concerning use of

the appliance in a safe way and understand the

hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall

not be made by children without supervision.

– Do not dry unwashed items in the tumble dryer.

– Items that have been soiled with substances

such as cooking oil, acetone, alcohol, petrol,

kerosene, spot removers, turpentine, waxes

and wax removers should be washed in hot

water with an extra amount of detergent before

being dried in the tumble dryer.

– Items such as foam rubber (latex foam),

shower caps, waterproof textiles, rubber

backed articles and clothes or pillows fitted

with foam rubber pads should not be dried in

the tumble dryer.

– Fabric softeners, or similar products, should

be used as specified by the fabric softener

instructions.

– The final part of a tumble dryer cycle occurs

without heat (cool down cycle) to ensure that the

items are left at a temperature that ensures that

the items will not be damaged.

WARNING: Never stop a tumble dryer before

the end of the drying cycle unless all items are

quickly removed and spread out so that the

heat is dissipated.

• This appliance was designed for domestic use only.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not touch the drained water as it may reach extremely

high temperatures.

• Never force the porthole door. This could damage the safety

lock mechanism designed to prevent accidental opening.

• If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• If it must be moved, proceed with the help of two or three

people and handle it with the utmost care. Never try to do

this alone, because the appliance is very heavy.

• Before loading laundry into the washer dryer, make sure

the drum is empty.

• During the drying phase, the door tends to get quite hot.

• Do not use the appliance to dry clothes that

have been washed with flammable solvents

(e.g. trichlorethylene).

• Do not use the appliance to dry foam rubber

or similar elastomers.

• Make sure that the water tap is turned on during the drying

cycles.

Opening the porthole door manually

In the event that it is not possible to open the porthole door

due to a powercut, and if you wish to remove the laundry,

proceed as follows:

1. remove the plug from the electrical socket.

2. make sure the water level inside the machine is lower than

the door opening; if it is not, remove excess water using the

drain hose, collecting it in a bucket as indicated in the figure.

3. using a screwdriver, remove the cover panel on the lower

front part of the washer-dryer (see figure).

4. pull outwards using the tab as indicated in the figure,

until the plastic tie-rod is freed from its stop position; pull

downwards and open the door at the same time.

5. reposition the panel, making sure the hooks are securely

in place before you push it onto the appliance.

20

• Children of less than 3 years should be kept

away from the appliance unless continuou-

sly supervised.

• Remove all objects from pockets such as

lighters and matches.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2012/19/EU - WEEE on Waste

Electrical and Electronic Equipment, requires that old

household electrical appliances must not be disposed of in

the normal unsorted municipal waste stream. Old appliances

must be collected separately in order to optimise the recovery

and recycling of the materials they contain and reduce the

impact on human health and the environment. The crossed

out “wheeled bin” symbol on the product reminds you of

your obligation, that when you dispose of the appliance it

must be separately collected. Consumers should contact

their local authority or retailer for information concerning the

correct disposal of their old appliance.

8

GB

Description of the washer-dryer

Control panel

TEMPERATURE

button

WASH

CYCLE

SELECTOR

KNOB

Detergent dispenser drawer

ON/OFF

button

SPIN

button

START/PAUSE

button and indicator

light

DISPLAY

DRYING

button

OPTION

buttons and

indicator lights

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents and

laundry”).

ON/OFF button: press this briefly to switch the

machine on or off. The START/PAUSE indicator light which

flashes slowly in a green colour shows that the machine

is switched on. To switch off the washer-dryer during the

wash cycle, press and hold the button for approximately 3

seconds; if the button is pressed briefly or accidentally the

machine will not switch off.

If the machine is switched off during a wash cycle, this

wash cycle will be cancelled.

WASH CYCLE SELECTOR KNOB: used to set the

desired wash cycle (see “Table of programmes and wash

cycles”).

OPTION buttons and indicator lights: press to select the

available options. The indicator light corresponding to the

selected option will remain lit.

CLEANING ACTION

button : to select the desired

wash intensity.

TEMPERATURE button: press to reduce or

completely exclude the temperature; the value appears on

the display.

SPIN button: press to reduce or completely exclude

the spin cycle; the value appears on the display.

DRYING button : press to decrease or exclude drying;

the selected drying level or time will appear on the display.

START/PAUSE button and indicator light: when the green

indicator light flashes slowly, press the button to start a

wash cycle. Once the cycle has begun the indicator light

will remain lit in a fixed manner. To pause the wash cycle,

press the button again; the indicator light will flash in an

amber colour. If the symbol is not illuminated, the door

may be opened. To start the wash cycle from the point at

which it was interrupted, press the button again.

CHILD LOCK button : to activate the control panel

lock, press and hold the button for approximately 2

seconds. When the symbol is illuminated, the control

panel is locked. This means it is possible to prevent wash

cycles from being modified accidentally, especially where

there are children in the home. To deactivate the control

panel lock, press and hold the button for approximately 2

seconds.

Standby mode

This washer-dryer, in compliance with new energy saving

regulations, is fitted with an automatic standby system

which is enabled after about 30 minutes if no activity is

detected. Press the ON-OFF button briefly and wait for the

machine to start up again.

Consumption in off-mode: 0,5 W

Consumption in Left-on: 8 W

CLEANING

ACTION

button

CHILD

LOCK

button

9

GB

Display

B

C

A

The display is useful when programming the machine and provides a great deal of information.

The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAYED

START option has been set, the countdown to the start of the selected wash cycle will appear.

Moreover, pressing the relative button allows for visualising the maximum values for the temperature, spin speed or type of

drying relative to the selected programme or the most recently selected ones, if compatible with the selected programme.

The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle

appear in section B:

Main wash

Rinse

Spin/Pump out

Drying

The icons corresponding to “temperature”, “spin” and “drying” (working from the left) are displayed in section C.

The “temperature” bars indicate the maximum temperature level which may be selected for the set cycle.

The “spin” bars indicate the maximum spin level which may be selected for the set cycle.

The symbol lights up while the drying settings are being adjusted.

DOOR LOCKED indicator light:

The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the door.

To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched

off the door may be opened.

10

GB

How to run a wash cycle or a

drying cycle

1. SWITCH THE MACHINE ON. Press the button; the

START/PAUSE indicator light will flash slowly in a green colour.

2. LOAD THE LAUNDRY. Open the porthole door. Load

the laundry, making sure you do not exceed the maximum

load value indicated in the table of programmes and wash

cycles on the following page.

3. MEASURE OUT THE DETERGENT. Pull out the

detergent dispenser drawer and pour the detergent into

the relevant compartments as described in “Detergents

and laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Use the WASH CYCLE

SELECTOR knob to select the desired wash cycle. A

temperature and spin speed is set for each wash cycle;

these values may be adjusted. The duration of the cycle will

appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant buttons:

Modify the temperature and/or spin speed. The

machine automatically displays the maximum temperature

and spin speed values set for the selected cycle, or the

most recently-used settings if they are compatible with

the selected cycle. The temperature can be decreased by

pressing the button, until the cold wash “OFF” setting

is reached. The spin speed may be progressively reduced

by pressing the button, until it is completely excluded

(the “OFF” setting). If these buttons are pressed again, the

maximum values are restored.

! Exception: if the

4

programme is selected, the

temperature can be increased up to a value of 90°C.

Setting the drying cycle

The first time the button is pressed, the machine will

automatically select the maximum drying cycle which is

compatible with the selected wash cycle. Subsequent

presses will decrease the drying level and then the drying

time, until the cycle is excluded completely (“OFF”).

Drying may be set as follows:

A- Based on the desired laundry dryness level:

Iron “A1”: suitable for clothes which will need ironing

afterwards. the remaining dampness softens creases,

making them easier to remove.

Hanger “A2”: ideal for clothes which do not need to be dried fully.

Cupboard “A3”: suitable for laundry which can be put

back in a cupboard without being ironed.

Extra “A4”: suitable for garments which need to be dried

completely, such as sponges and bathrobes.

B - Based on a set time period: between 30 and 180

minutes.

If your laundry load to be washed and dried is much

greater than the maximum stated load, perform the wash

cycle, and when the cycle is complete, divide the garments

into groups and put some of them back in the drum. At this

point, follow the instructions provided for a “Drying only”

cycle. Repeat this procedure for the remainder of the load.

A cooling-down period is always added to the end of each

drying cycle.

Drying only

Use the cycle selector knob to select a drying cycle (12-13-14)

in accordance with the type of fabric. The desired drying level or

time may also be set using the DRYING button .

Selecting the cotton drying cycle through the programme

selector knob and pressing the “Eco” button activates an

automatic drying cycle that allows for saving energy, thanks

to an optimal combination of air temperature and cycle

duration; the display will visualise the “A2” dryness level.

Set the desired wash intensity.

Option makes it possible to optimise washing based

on the level of soil in the fabrics and on desired wash cycle

intensity.

Select the wash programme: the cycle will be automatically

set to “Normal” as optimised for garments with an average

level of soil (this setting is not applicable to the “Wool”

cycle, which is automatically set to “Delicate”).

For heavily-soiled garments press button until the

“Intensive” level is reached. This level ensures a high-

performance wash due to a larger quantity of water used

in the initial phase of the cycle and due to increased drum

rotation. It is useful when removing the most stubborn stains.

It can be used with or without bleach. If you desire bleaching,

insert the extra tray compartment (4) into compartment 1.

When pouring in the bleach, be careful not to exceed the

“max” level marked on the central pivot (see figure pag. 12).

For lightly-soiled garments or a more delicate treatment

of the fabrics, press button until the “Delicate” level

is reached. The cycle will reduce drum rotation to ensure

washing results that are perfect for delicate garments.

Modify the cycle settings.

• Press the button to enable the option; the indicator light

corresponding to the button will switch on.

• Press the button again to disable the option; the

indicator light will switch off.

! If the selected option is not compatible with the set wash

cycle, the indicator light will flash and the option will not be

activated.

! If the selected option is not compatible with a previously

selected one, the indicator light corresponding to the first

function selected will flash and only the second option will

be activated; the indicator light for the option which has been

activated will be illuminated.

! The options may affect the recommended load value and/

or the duration of the cycle.

7. START THE WASH CYCLE. Press the START/PAUSE

button. The corresponding indicator light will turn green,

remaining lit in a fixed manner, and the door will be locked (the

DOOR LOCKED symbol will be lit). To change a wash

cycle while it is in progress, pause the washer-dryer using the

START/PAUSE button (the START/PAUSE indicator light will

flash slowly in an amber colour); then select the desired cycle

and press the START/PAUSE button again. To open the door

while a cycle is in progress, press the START/PAUSE button; if

the DOOR LOCKED symbol is switched off the door may

be opened. Press the START/PAUSE button again to restart

the wash cycle from the point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This will be indicated

by the text “END” on the display; when the DOOR LOCKED

symbol switches off the door may be opened. Open the

door, unload the laundry and switch off the machine.

! If you wish to cancel a cycle which has already begun, press

and hold the button. The cycle will be stopped and the

machine will switch off.

11

GB

Wash cycles and options

Wash options

! If the selected option is not compatible with the set wash

cycle, the indicator light will flash and the option will not

be activated.

! If the selected option is not compatible with a previously

selected one, the indicator light corresponding to the first

function selected will flash and only the second option will

be activated; the indicator light for the option which has

been activated will be illuminated.

Eco

The Eco option saves energy by not heating the water

used to wash your laundry – an advantage both to the

environment and to your energy bill. Instead, intensified

wash action and water optimisation ensure great wash

results in the same average time of a standard cycle.

For the best washing results we recommend the usage of

a liquid detergent

By selecting the drying function as well, an automatic

drying cycle automatically activates at the end of the wash

cycle – it too allows for saving energy, thanks to the optimal

combination of air temperature and cycle duration.

Table of programmes and wash cycles

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary

according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options

selected.

Wash cycles

Description of the wash cycle

Max.

temp. (°C)

Max.

speed

(rpm)

Drying

Detergents

Max.

load

(kg)

Cycle

duration

Prewash Wash Bleach

Fabric

softener

1

Anti Stain

40° 1400



-



-



5

2

Whites

60° 1400



-



-



5

3

Cotton + Prewash: extremely soiled whites. 90° 1400

  

-



8

4

Cotton (1-2): heavily soiled whites and resistant colours.

60°

(Max. 90°)

1400



-



-



8

5

Cotton: lightly soiled resistant colours. 40° 1400



-



-



8

6

Synthetics: heavily soiled resistant colours. 60° 1000



-

  

4

7

Anti allergy

60° 1400



-

  

5

8

Wool: for wool, cashmere, etc. 40° 800



-



-



2

9

Delicates

30° 0



-



-



1

10

Fast Wash 30’: to refresh lightly soiled garments

quickly (not suitable for wool, silk and clothes which

require washing by hand).

30° 800 - -



-



3,5

11

Wash&Dry

30° 1400



-



-



1

12

Drying Cottons

- -



- - - - 6

13

Drying Synthetics

- -



- - - - 4

14

Drying Wool

- -



- - - - 2

Rinse - 1400



- - -



8

Spin and Pump out - 1400



- - - -

8

The duration of the wash cycles can be checked on the display.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 50229: set wash cycle 4 with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle 5 with a temperature of 40°C.

Delay Timer

To set a delayed start for the selected cycle, press the

corresponding button repeatedly until the required delay

period has been reached. When this option is enabled, the

corresponding indicator light will remain lit. To remove the

delayed start setting, press the button until the text “OFF”

appears on the display.

12

GB

Detergents and laundry

Detergent dispenser drawer

Successful washing results also depend on the correct

dose of detergent: adding too much detergent will not

necessarily result in a more efficient wash, and may in

fact cause build up on the inside of your appliance and

contribute to environmental pollution.

! Do not use hand washing detergents; they create too

much foam.

Open the detergent

dispenser drawer and pour

in the detergent or washing

additive, as follows.

compartment 1: Pre-

wash detergent (powder)

Before pouring in the

detergent, make sure that

extra compartment 4 has

been removed.

compartment 2: Detergent for the wash cycle

(powder or liquid)

If liquid detergent is used, it is recommended that the removable

plastic partition A (supplied) be used for proper dosage. If

powder detergent is used, place the partition into slot B.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

extra compartment 4: Bleach

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Empty all garment pockets and check the buttons.

• Do not exceed the values listed in the “Table of wash cycles”,

which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1,200 g

1 towel 150-250 g

Special wash cycles

Anti Stain: the programme 1 is suitable to heavily-soiled

garments with resistant colours. It ensures a washing class

that is higher than the standard class (A class).

When running the programme, do not mix garments of

different colours. We recommend the use of powder

detergent. Pre-treatment with special additives is

recommended if there are obstinate stains.

Whites: use this cycle 2 to wash white clothes. The

programme is designed to maintain the brightness of white

clothes over time. Use powder detergent for best results.

If the drying function is selected, a drying cycle automatically

activates at the end of the wash cycle that resembles open-

M

AX

1

2

4

3

A

B

air drying, with the added advantages of preserving garments

from yellowing due to sunlight exposure and preventing loss

of whiteness caused by the possible presence of dust in the

air. Drying cycles can only be selected on a level basis.

Anti allergy: use programme 7 to remove major allergens

such as pollen, mites, cat’s and dog’s hair.

Wool: the wool wash cycle on this Ariston machine has

been tested and approved by The Woolmark Company

for washing wool garments labelled as hand washable

provided that the garments are washed according to the

instructions on the garment label and those issued by the

manufacturer of this washing machine. Ariston is the first

washing machine brand to be approved by The Woolmark

Company for Apparel Care- Platinum for its washing

performance and consumption of energy and water.

(M1127)

.

Delicates: use programme 9 to wash very delicate

garments having strasses or sequins.

We recommend turning the garments inside out before

washing and placing small items into the special bag

for washing delicates. Use liquid detergent on delicate

garments for best results.

When selecting an exclusively time-based drying function,

a drying cycle is performed at the end of the wash cycle

that is particularly delicate, thanks to light handling and

appropriate temperature control of the water jet.

The recommended durations are:

1 kg of synthetic garments --> 150 min

1 kg of synthetic and cotton garments --> 180 min

1 kg of cotton garments --> 180 min

The degree of dryness depends on the load and fabric

composition.

To wash silk garments and curtains select the cycle 9 and

set the “Delicate” level from option .

Wash&Dry select programme 11 for washing and drying

lightly soiled garments (Cotton and Synthetic) in a short

time. This cycle may be used to wash and dry a laundry

load of up to 1 kg in just 45 minutes.

To achieve optimum results, use liquid detergent and pre-

treat cuffs, collars and stains.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

before every spin and to distribute the load in a uniform

manner, the drum rotates continuously at a speed which

is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the load is

excessively unbalanced, the washer-dryer performs the

distribution process instead of spinning. To encourage

improved load distribution and balance, we recommend

small and large garments are mixed in the load.

13

GB

Troubleshooting

Your washer-dryer could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”), make

sure that the problem cannot be not solved easily using the following list.

Problem:

The washer-dryer does not switch

on.

The wash cycle does not start.

The washer-dryer does not fill

with water (the text “H2O” flashes

on the display).

The washer-dryer continuously

takes in and drains water.

The washer-dryer does not drain

or spin.

The washer-dryer vibrates a lot

during the spin cycle.

The washer-dryer leaks.

The “option” and START/PAUSE

indicator lights flash rapidly and an

error code appears on the display (e.g.:

F-01, F-..).

There is too much foam.

The washer-dryer does not dry.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or not enough to make contact.

• There is no power in the house.

• The washer-dryer door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set.

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

• The free end of the hose is under water (see “Installation”).

• The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch the

appliance off and contact the Technical Assistance Service. If the dwelling is on one

of the upper floors of a building, there may be problems relating to water drainage,

causing the washer-dryer to fill with water and drain continuously. Special anti-

draining valves are available in shops and help to prevent this inconvenience.

• The wash cycle does not include draining: some cycles require the draining

process to be enabled manually.

• The drain hose is bent (see “Installation”).

• The drainage duct is clogged.

• The drum was not unlocked correctly during installation (see “Installation”).

• The washer-dryer is not level (see “Installation”).

• The washer-dryer is trapped between cabinets and walls (see “Installation”).

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser drawer is blocked (for cleaning instructions, see “Care

and maintenance”).

• The drain hose is not fixed properly (see “Installation”).

• Switch off the machine and unplug it, wait for approximately 1 minute and then

switch it back on again.

If the problem persists, contact the Technical Assistance Service.

• The detergent is not suitable for machine washing (it should display the text

“for washing machine” or “hand and machine wash”, or the like).

• Too much detergent was used.

• The appliance is not plugged into the socket, or not enough to make contact.

• There has been a power failure.

• The appliance door is not shut properly.

• A DELAY TIMER has been set.

• DRYING is in the OFF position.

14

GB

Service

Before contacting the Technical Assistance Service:

• Check whether you can solve the problem alone (see “Troubleshooting”);

• Restart the wash cycle to check whether the problem has been solved;

• If this is not the case, contact an authorised Technical Assistance Centre.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• the type of problem;

• the appliance model (Mod.);

• the serial number (S/N).

This information can be found on the data plate applied to the rear of the washer-dryer, and can also be found on the front of

the appliance by opening the door.

ES

15

Español

ES

LAVASECADORA

! Este símbolo te recuerda que debes leer

este manual de instrucciones.

Sumario

Instalación, 16-17-18-19

Desembalaje y nivelación

Conexiones hidráulicas y eléctricas

Primer ciclo de lavado

Datos técnicos

Mantenimiento y cuidados, 20

Interrumpir el agua y la corriente eléctrica

Limpiar la lavasecadora

Limpiar el contenedor de detergentes

Cuidar la puerta y el cesto

Limpiar la bomba

Controlar el tubo de alimentación de agua

Precauciones y consejos, 21

Seguridad general

Eliminación

Apertura manual de la puerta

Descripción de la lavasecadora, 22-23

Panel de control

Pantalla

Cómo efectuar un ciclo de lavado o de

secado, 24

Programas y opciones, 25

Tabla de programas

Opciones de lavado

Detergentes y ropa, 26

Contenedor de detergentes

Preparar la ropa

Programas particulares

Anomalías y soluciones, 27

Asistencia Técnica, 28

WDG 8640

Manual de instrucciones

16

ES

Instalación

! Es importante conservar este manual para

poder consultarlo en cualquier momento. En

caso de venta, de cesión o de traslado, verifique

que permanezca junto con la lavasecadora

para informar al nuevo propietario sobre el

funcionamiento y brindar las correspondientes

advertencias.

! Lea atentamente las instrucciones: ellas

contienen importante información sobre la

instalación, el uso y la seguridad.

Desembalaje y nivelación

Desembalaje

1. Desembale la lavasecadora.

2. Controle que la lavasecadora no haya sufrido

daños durante el transporte. Si estuviera dañada

no la conecte y llame al revendedor.

3. Quite los 4 tornillos

de protección para

el transporte y la

arandela de goma

con el correspondiente

distanciador ubicados

en la parte posterior

(ver la figura).

4. Cubra los orificios con los tapones de plástico

suministrados con el aparato.

5. Conserve todas las piezas: cuando la

lavasecadora deba ser transportada nuevamente,

deberán volver a colocarse.

! Los embalajes no son juguetes para los niños.

Nivelación

1. Instale la lavasecadora sobre un piso plano y

rígido, sin apoyarla en las paredes, muebles ni en

ningún otro aparato.

2. Si el piso no está

p e r f e c t a m e n t e

horizontal, compense

las irregularidades

dese nroscan do o

enroscando las patas

delanteras (ver la figura);

el ángulo de inclinación

m ed i d o s ob r e l a

superficie de trabajo,

no debe superar los 2º.

Una cuidadosa nivelación brinda estabilidad

a la máquina y evita vibraciones, ruidos y

desplazamientos durante el funcionamiento.

Cuando se instala sobre moquetas o alfombras,

regule los pies para conservar debajo de la

lavasecadora un espacio suficiente para la

ventilación.

Conexiones hidráulicas y eléctricas

Conexión del tubo de alimentación de

agua

1. Conectar el tubo de

tubo enroscándolo a

un grifo de agua fría

con la boca roscada de

3/4 gas (ver la figura).

Antes de conectarlo,

haga correr el agua

hasta que esté límpida.

2. Conecte el tubo

d e a l i m e n t a c i ó n

a la lavasecadora

e n r o s c á n d o l o e n

la to ma d e agu a

c o r r e s p o n d i e n t e

ubicada en la parte

posterior derecha

(arriba) (ver la figura).

3. Controle que en el tubo no hayan pliegues ni

estrangulaciones.

! La presión de agua del grifo debe estar

comprendida dentro de los valores contenidos

en la tabla de Datos técnicos (ver la página

correspondiente).

! Si la longitud del tubo de alimentación no es la

suficiente, diríjase a un negocio especializado o

a un técnico autorizado.

! No utilice nunca tubos ya usados.

! Utilice los suministrados con la máquina.

ES

17

65 - 100 cm

Conexión del tubo de descarga

Conecte el tubo de

descarga, sin plegarlo,

a una tube ría de

descarga o a una

descarga de pared

colocadas a una altura

del piso entre 65 y 100

cm;

o apóyelo en el borde

de un lavamanos o de

una bañera, uniendo

la guía suministrada

con el aparato, al

grifo (ver la figura).

El extremo libre del

tubo de descarga no

debe permanecer

sumergido en el agua.

! No se aconseja utilizar tubos de prolongación,

si fuera indispensable hacerlo, la prolongación

debe tener el mismo diámetro del tubo original

y no superar los 150 cm.

Conexión eléctrica

Antes de enchufar el aparato, verifique que:

•latomatengalaconexiónatierrayhayasido

hecha según las normas legales;

•latomaseacapazdesoportarlacargamáxima

de potencia de la máquina indicada en la tabla

de Datos técnicos;

•latensióndealimentaciónestécomprendida

dentro de los valores indicados en la tabla de

Datos técnicos (ver al costado);

•latomaseacompatibleconelenchufedela

lavadora. Si no es así, sustituya la toma o el

enchufe.

Su electrodoméstico dispone ahora de un

enchufe con fusible de 13 ampere que se puede

introducir en una toma compatible para un uso

inmediato. Lea las siguientes instrucciones antes

de utilizar el electrodoméstico.

ATENCIÓN - EL ELECTRODOMÉSTICO DEBE

ESTAR CONECTADO A TIERRA.

LAS ACTIVIDADES QUE SE DESCRIBEN A

CONTINUACIÓN DEBEN SER REALIZADAS

POR UN ELECTRICISTA ESPECIALIZADO.

Sustitución del fusible:

Cuando sustituya un fusible defectuoso, utilice

siempre fusibles de 13 ampere ASTA que

cumplan con el estándar BS1362 y luego

coloque la tapa del fusible. Si la tapa del fusible

se hubiera perdido, no utilice el enchufe hasta

que no se haya encontrado la pieza o se

sustituya con una nueva.

Tapas de fusibles:

Si se sustituye la tapa del fusible, verifique que

el color sea el que se indica en la codificación o

en la inscripción de color que se encuentra en la

base del enchufe. Para conseguir los repuestos,

llame directamente al centro de asistencia

técnica más cercano.

Desmontaje del enchufe:

Si el electrodoméstico posee un enchufe

incorporado que no puede ser nuevamente

cableado y sea necesario hacer pasar el cable

a través de divisiones, unidades, etc., verifique

que:

el enchufe se sustituya con otro que se pueda

cablear, de 13 ampere y que posea la marca BSI

o

el cable de red esté conectado directamente

a la toma de 13 ampere, controlada por un

interruptor (que cumpla con la norma BS 5733)

al que se pueda acceder sin tener que desplazar

el electrodoméstico.

Eliminación del enchufe:

Antes de eliminar el enchufe, inutilice las

patitas, de modo que no pueda ser introducido

accidentalmente en una toma.

Instrucciones para la conexión del cable a un

enchufe alternativo:

Importante: el color de los cables de la red

respeta la siguiente codificación:

Amarillo/Verde Tierra

Azul Neutro

Marrón Cargado

18

ES

conecte el cable amarillo/verde al borne

marcado con E o o de color verde o

amarillo/verde;

conecte el cable marrón al borne marcado

con L o de color rojo;

conecte el cable azul al borne marcado con N

o de color negro.

Si se utiliza un enchufe de 13 ampere (BS

1363), instale un fusible de 13 ampere en el

enchufe, en el adaptador o en la placa de

distribución.

En caso de dudas sobre la alimentación

eléctrica de su electrodoméstico, llame a un

electricista especializado antes del uso.

Conexión de un enchufe alternativo:

El color de los cables de la red respeta la

siguiente codificación:

AZUL NEUTRO (N)

MARRÓN CARGADO (L)

AMARILLO/VERDE TIERRA (E)

Eliminación del electrodoméstico:

Cuando elimine el electrodoméstico, quite el

enchufe cortando el cable de alimentación lo

más cerca posible del mismo y elimínelo como

se describió precedentemente.

! La lavadora no debe ser instalada al aire

libre, ni siquiera si el lugar está reparado, ya

que es muy peligroso dejarla expuesta a la

lluvia o a las tormentas.

! Una vez instalada la lavadora, la toma de

corriente debe ser fácilmente accesible.

! No utilice prolongaciones ni conexiones

múltiples.

! El cable no debe estar plegado ni sufrir

compresiones.

! El cable de alimentación debe ser sustituido

sólo por técnicos autorizados.

¡Atención! La empresa fabricante declina toda

responsabilidad en caso de que estas normas

no sean respetadas.

Primer ciclo de lavado

Después de la instalación y antes del uso,

realice un ciclo de lavado con detergente y

sin ropa, seleccionando el programa “Auto

Limpieza” (ver “Limpiar la lavadora”).

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

ES

19

Datos técnicos

Modelo

WDG 8640

Dimensio-

nes

ancho 59.5 cm

altura 85 cm

profundidad 54 cm

Capacidad

de 1 a 8 kg para el lavado

de 1 a 6 kg para el secado

Conexiones

eléctricas

ver la placa de característi-

cas técnicas aplicada en la

máquina

Conexiones

hídricas

presión máxima 1 MPa (10

bar)

presión mínima 0,05 MPa

(0,5 bar)

capacidad del cesto 58

litros

Velocidad de

centrifugado

máxima 1400 r.p.m.

Programas

de control

según la re-

glamentos

EN 50229

lavado: programa 4; tempe-

ratura 60ºC;

efectuado con 8 kg. de carga.

secado: el secado de la car-

ga menor debe realizarse se-

leccionando el nivel de seca-

do “A1” (IRON), la carga de

ropa se debe componer de 2

sábanas, 1 funda y 1 toalla;

el secado de la carga que

queda debe realizarse selec-

cionando el nivel de secado

“A4” (EXTRA).

Esta máquina cumple con lo

establecido por las siguien-

tes Directivas de la Comuni-

dad:

- 2004/108/CE (Compatibili-

dad Electromagnética)

- 2012/19/EU - WEEE

- 2006/95/CE (Baja Tensión)

20

ES

Mantenimiento y cuidados

Cuidar la puerta y el cesto

•Dejesiempresemicerradalapuertaparaevitar

que se formen malos olores.

Limpiar la bomba

La lavasecadora posee una bomba autolimpiante

que no necesita mantenimiento. Pero puede

suceder que objetos pequeños (monedas,

botones) caigan en la precámara que protege la

bomba, situada en la parte inferior de la misma.

! Verifique que el ciclo de lavado haya terminado

y desenchufe la máquina.

Para acceder a la precámara:

1. quite el panel que

cubre la parte delantera

de la lavasecadora

con la ayuda de un

destornillador (ver la

figura);

2. desenrosque la tapa

girándola en sentido

antihorario (ve r la

figura): es normal que

se vuelque un poco de

agua;

3. limpie con cuidado el interior;

4. vuelva a enroscar la tapa;

5. vuelva a montar el panel verificando, antes de

empujarlo hacia la máquina, que los ganchos

se hayan introducido en las correspondientes

ranuras.

Controlar el tubo de alimentación de

agua

Controle el tubo de alimentación al menos una

vez al año. Si presenta grietas o rajaduras debe

ser sustituido: durante los lavados, las fuertes

presiones podrían provocar roturas imprevistas.

! No utilice nunca tubos ya usados.

Interrumpir el agua y la corriente

eléctrica

•Cierre el grifo de agua después de cada

lavado. De este modo se limita el desgaste de

la instalación hidráulica de la lavasecadora y

se elimina el peligro de pérdidas.

•Desenchufelamáquinacuandoladebelimpiar

y durante los trabajos de mantenimiento.

Limpiar la lavasecadora

• La parte externay las partes de goma se

pueden limpiar con un paño embebido en agua

tibia y jabón. No use solventes ni productos

abrasivos.

•Lalavasecadoraposeeunprogramade“Auto

Limpieza” de su interior que se debe realizar sin

ningún tipo de carga en el cesto.

El detergente (en un 10% de la cantidad

aconsejada para prendas poco sucias) o

algunos aditivos específicos para la limpieza de

la ropa se podrán utilizar como coadyuvantes en

el programa de lavado. Se aconseja efectuar el

programa de limpieza cada 40 ciclos de lavado.

Para activar el programa, presionar el boton A

durante 5 segundos (ver la figura).

El programa comenzará automáticamente

y tendrá una duración de 70 minutos

aproximadamente. Para detener el ciclo presione

el botón START/PAUSE.

L i m p i a r e l c o n t e n e d o r d e

detergentes

Extraiga el contenedor

l e v a n t á n d o l o y

tirándolo hacia fuera

(ver la figura).

Lávelo debajo del agua

corriente, esta limpieza

s e d e b e r e a l i z a r

frecuentemente.

1

2

A

La page est en cours de chargement...

Whirlpool WDG 8640S EX Mode d'emploi

Whirlpool WDG 8640S EX Mode d'emploi

dans d''autres langues