GE Appliances GSE25HSHSS Guide d'installation

GEAppliances.com

Refrigerators

Side by Side

200D8074P051 49-60646-3 03-14 GE

La section française commence à la page 40

La sección en español empieza en la página 75

Safety Instructions .................2–3

Operating Instructions

Automatic Icemaker ..................12,13

Care and Cleaning ...................15,16

Crispers and Pans .......................11

ExpressChill

™

.............................5

Ice and Water Dispenser ................14

Refrigerator Doors ......................10

Replacing the Light Bulbs .............16,17

Shelves and Bins .......................8, 9

Temperature Controls ....................4

TurboCool

™

..............................5

ClimateKepper2 ..........................5

Water Filter ..............................7

Installation Instructions

Installing the Refrigerator ............23–26

Moving the Refrigerator .............19–22

Preparing to Install

the Refrigerator .........................18

Water Line Installation ..............27–29

Troubleshooting Tips ............31–33

Normal Operating Sounds ...............30

Consumer Support

Consumer Support .............Back Cover

Performance Data Sheet .............34,35

State of California Water

Treatment Device Certificate .............36

Warranty (U.S.) ..........................37

Warranty (Canadian) ....................38

Product Registration (Canadian)

......... 39

Notes ...................................40

Réfrigérateurs

Côte à Côte

Refrigeradores

Lado a Lado

Models 22, 23, 25,26,27 and 29

Write the model and serial numbers here:

Model # _________________________

Serial # __________________________

Find these numbers on a label inside the

refrigerator compartment at the top on the

right side.

Owner’s Manual

and Installation

Manuel d’utilisation

et d’installation

Manual del propietario

e instalación

2

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

 This refrigerator must be properly installed and located in

accordance with the Installation Instructions before it is used.

 Do not allow children to climb, stand or hang on the shelves

in the refrigerator. They could damage the refrigerator and

seriously injure themselves.

 Do not touch the cold surfaces in the freezer compartment

when hands are damp or wet. Skin may stick to these

extremely cold surfaces.

 Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

 In refrigerators with automatic icemakers, avoid contact

with the moving parts of the ejector mechanism, or with

the heating element located on the bottom of the icemaker.

Do not place fingers or hands on the automatic icemaking

mechanism while the refrigerator is plugged in.

 Keep fingers out of the “pinch point” areas; clearances

between the doors and between the doors and cabinet are

necessarily small. Be careful closing doors when children are

in the area.

 Unplug the refrigerator before cleaning and making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

 Do not refreeze frozen foods which have thawed completely.

NOTE: Turning the refrigerator off via the controls on the touch

panel does not shut off electrical power to the refrigerator.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

GEAppliances.com

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems of the past.

Junked or abandoned refrigerators are still dangerous…even if

they will sit for “just a few days.” If you are getting rid of your old

refrigerator, please follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old Refrigerator or

Freezer:

 Take off the doors.

 Leave the shelves in place so that children may not easily

climb inside.

Refrigerants

All refrigeration products contain refrigerants, which under

federal law must be removed prior to product disposal. If you

are getting rid of an old refrigeration product, check with the

company handling the disposal about what to do.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension

cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United States) or a CSA-listed (in

Canada), 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of

the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

3

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this

appliance must be properly grounded.

The power cord of this appliance is equipped with a 3-prong

(grounding) plug which mates with a standard 3-prong

(grounding) wall outlet to minimize the possibility of electric

shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

If the outlet is a standard 2-prong outlet, it is your personal

responsibility and obligation to have it replaced with a properly

grounded 3-prong wall outlet.

The refrigerator should always be plugged into its own individual

electrical outlet which has a voltage rating that matches the

rating plate.

This provides the best performance and also prevents

overloading house wiring circuits which could cause a fire

hazard from overheated wires.

Never unplug your refrigerator by pulling on the power cord.

Always grip plug firmly and pull straight out from the outlet.

Repair or replace immediately all power cords that have

become frayed or otherwise damaged. Do not use a cord that

shows cracks or abrasion damage along its length or at either

end.

When moving the refrigerator away from the wall, be careful not

to roll over or damage the power cord.

About the temperature controls.

4

The temperature controls are preset in the factory at 37°F for the refrigerator compartment and 0°F for the

freezer compartment. Allow 24 hours for the temperature to stabilize to the preset recommended settings.

The temperature controls can display both the SET temperature as well as the actual temperature in the

refrigerator and freezer. The actual temperature may vary slightly from the SET temperature based on usage

and operating environment.





On some models, setting both controls to the warmest setting until the display flashes (off) will stop

cooling in both the freezer and refrigerator compartments.





On other models, setting either control to the warmest setting until the display flashes (off) will stop the

cooling to the freezer and refrigerator.





NOTE: Turning the refrigerator off via the controls on the touch panel does not shut off electrical power to

the refrigerator.

NOTE: The refrigerator is shipped with protective film- covering the temperature controls. If this film was not

removed during installation, remove it now.

Not all features are on all models. Your controls may be similar to the following:

The Performance Air-Flow System is designed to

maximize temperature control in the refrigerator and

freezer compartments. This unique special feature

consists of the Air Tower along the back wall of the

refrigerator and the Air Tunnel on the bottom portion

of the freezer rear wall.

Placing food in front of the louvers on these

components will not affect performance. Although

the Air Tower and the Air Tunnel can be removed,

doing so will affect temperature performance. (For

removal instructions, on-line, 24 hours a day, contact

us at GEAppliances.com or call 800.GE.CARES.

In Canada, contact us at geappliances.ca or call

1.800.561.3344.)

Performance Air Flow System

OR

5

TurboCool

™

rapidly cools the refrigerator

compartment in order to more quickly cool foods.

Use TurboCool

™

when adding a large amount

of food to the refrigerator compartment, putting

away foods after they have been sitting out at room

temperature or when putting away warm leftovers.

It can also be used if the refrigerator has been

without power for an extended period.

Once activated, the compressor will turn on

immediately and the fans will cycle on and off

at high speed as needed for eight hours. The

compressor will continue to run until the refrigerator

compartment cools to approximately 34°F (1°C),

then it will cycle on and off to maintain this setting.

After 8 hours, or if TurboCool

™

is pressed again,

the refrigerator compartment will return to the

original setting.

How to Use

Press TurboCool.

™

The TurboCool

™

temperature

display will show Tc and the LED will be activated.

After TurboCool

™

is complete, the TurboCool

™

indicator light will go out.

NOTES: The refrigerator temperature cannot be

changed during TurboCool

™

.

The freezer temperature is not affected

during TurboCool

™

.

When opening the refrigerator door during

TurboCool

™

, the fans will continue to run

if they have cycled on.

About TurboCool.™ (on some models)

How it Works

OR

About ClimateKeeper2.

™

(on some models) GEAppliances.com

How it Works

The ClimateKeeper2

™

is the industry’s most

advanced refrigeration system, delivering

optimum temperature and humidity

performance to keep food garden fresh longer

and reduce freezer burn.

The ClimateKeeper2

™

system features two

HYDSRUDWRUV³RQHIRUWKHUHIULJHUDWRUDQGRQH

for the freezer.

This provides two separate cooling systems,

and separates the airflow between the fresh

food and freezer compartments during normal

cooling operations.*

This ensures that the humidity levels in the

fresh food compartment are significantly higher

than in a conventional system,** allowing fresh

produce and other unsealed foods to retain

their moisture content and freshness longer.

Moisture sensitive foods such as fresh fruit,

salads, rice, etc., can now be stored on open

shelves without excessive moisture loss.

Due to the higher humidity in the refrigerator,

you may on occasion experience fog or

small amounts of moisture in the refrigerator

compartment. This is normal and may

come and go as different food loads and

environmental conditions change. Wipe dry

with a paper towel if desired.

The separate airflow system minimizes the

mixing of air between the two compartments,

which reduces fresh food odor transfer to

improve the taste of ice.

The ClimateKeeper2

™

system also reduces

the number of defrosting cycles in the freezer

evaporator, thereby reducing freezer burn.

* Freezer air is used in the CustomCool

™

feature.

** Testing shows a higher level of humidity in

the Fresh Food section in ClimateKeeper2

™

refrigerators versus conventional units.

6

Empty the pan. Place the Chill tray in the

pan. Place the items on the tray and close

the pan completely.

Select the ExpressChill™ pad. On some

models, you can then select the chill time

(use chart to determine best setting). Other

models will only have one option (45

minutes). On models with multiple settings,

tap the pad until the light appears next to

the desired setting.





To stop a feature before it is finished, tap

that feature’s pad until no options are

selected and the display is off.





During ExpressChill™, the display on the

controls will count down the time in the

cycle.

About ExpressChill™. (on some models)

The ExpressChill™ feature is a system of

dampers, a fan and a temperature thermistor.

The pan is tightly sealed to prevent the pan’s

temperature from causing temperature

fluctuations in the rest of the refrigerator.

The controls for this pan are located in the top

of the refrigerator or on the dispenser with the

temperature controls.

How to Use

How it Works

ExpressChill™

To remove:

Pull the drawer out to the stop position.

Rotate all four swing locks to the unlock

position.

Lift the front of the drawer up and out.

To replace:

Make sure all four swing locks are in the

unlock position.

Place the sides of the drawer into the

drawer supports, making sure the swing

locks fit on the drawer slots.

Lock all four swing locks by rotating them

to the lock position.

How to Remove and Replace the Drawer

ExpressChill™ Chart (on some models)

NOTE: Results may vary depending on packaging, starting temperature and other food traits.

15 Minutes





1 Beverage Can (12 oz)





2 Small Juice Boxes

(6–8 oz each)

30 Minutes





2 to 6 Beverage Cans

(12 oz each)



2 Plastic 20 oz Bottles

of Beverage





4 to 6 Small Juice Boxes

(6–8 oz each)





3 Foil Juice Packets





Wine (750 ml bottle)

45 Minutes





2 Liters of Beverage





1/2 Gallon of Juice





*HODWLQ³SDFNDJH

About the water filter. (on some models) GEAppliances.com

7

Water Filter Cartridge

The water filter cartridge is located in the back upper right

corner of the refrigerator compartment.

When to Replace the Filter on Models With a

Replacement Indicator Light

There is a replacement indicator light for the water filter

cartridge on the dispenser. This light will turn orange to tell you

that you need to replace the filter soon.

The filter cartridge should be replaced when the replacement

indicator light turns red or if the flow of water to the dispenser or

icemaker decreases.

When to Replace the Filter on Models Without a

Replacement Indicator Light

The filter cartridge should be replaced every six months or

earlier if the flow of water to the water dispenser or icemaker

decreases.

Removing the Filter Cartridge

If you are replacing the cartridge, first remove the old one by

slowly turning it to the left. Do not pull down on the cartridge. A

small amount of water may drip down.

Installing the Filter Cartridge

If you are replacing a SmartWater cartridge with an

adapter, it must be removed before installing the cartridge.

To remove the adapter, turn it to the left about 1/4 turn.

If you are replacing a Water by Culligan cartridge, leave the

adapter in place. This adapter will stay in the refrigerator

when you replace future cartridges.

On models ithout a replacement indicator light, apply the

month and year sticker to the new cartridge to remind you

to replace the filter in six months.

Fill the replacement cartridge with water from the tap to

allow for better flow from the dispenser immediately after

installation.

Line up the arrow on the cartridge and the cartridge holder.

Place the top of the new cartridge up inside the holder. Do

not push it up into the holder.

Slowly turn it to the right until the filter cartridge stops. DO

NOT OVERTIGHTEN. As you turn the cartridge, it will

automatically raise itself into position. The cartridge will

move about 1/2 turn.

Run water from the dispenser 1-1/2 gallons (about three

minutes) to clear the system and prevent sputtering.

Press and hold the WATER FILTER pad (on some models) on

the dispenser for 3 seconds.

NOTE: A newly-installed water filter cartridge may cause water

to spurt from the dispenser upon first use.

Filter Bypass Plug

You must use the filter bypass plug when a replacement filter

cartridge is not available. The dispenser and the icemaker will

not operate without the filter or filter bypass plug.

To use the filter bypass plug on Water by Culligan models, you

must first remove the filter adapter from the cartridge holder by

turning it to the left.

For the maximum benefit of your filtration system, GE

recommends the use of GE branded SmartWater filters only.

Using GE branded filters in GE and Hotpoint refrigerators

provides optimal performance and reliability. GE branded

SmartWater filters are always the right choice because they

are patented and designed specifically for GE products. GE

SmartWater filters meet rigorous industry NSF standards for

safety and quality that are important for products that are

filtering your water. GE has not qualified non-GE branded

filters for use in GE and Hotpoint refrigerators and there is no

assurance that non-GE branded filters meet GE’s standards for

quality, performance and reliability.

,I\RXKDYHTXHVWLRQV³YLVLWRXU:HEVLWHDWGEAppliances.com,

or call 1.800.GE.CARES (1.800.432.2737).

Replacement filters:

To order additional filter cartridges in the United States, visit our

Website at GEAppliances.com, or call GE Parts and Accessories,

800.626.2002.

See filter label for type of filter to order (MWF or MSWF).

Customers in Canada should consult the yellow pages for the

nearest Mabe Service Center.

Filter

Bypass

Plug

Filter

Bypass

Plug

SmartWater

Water by Culligan

(appearance may vary)

With adapter

Without adapter

Cartridge

Holder

Some models

use this type of

water filter.

8

About the shelves and bins.

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Large Bins

The larger refrigerator door bins and freezer

tilt-out door bins are adjustable.

To remove: Lift the front of the bin straight up,

then lift up and out.

To replace or relocate: Engage the back side of

the bin in the molded supports of the door. Then

push down on the front of the bin. Bin will lock

in place.

Small Bins

To remove: Lift the front of the bin straight up

then out.

To replace: Position the bin above the

rectangular molded supports on the door. Then

slide the bin down onto the support to lock it in

place.

The snugger helps prevent tipping, spilling or

sliding of small items stored on the door shelf.

Place a finger on either side of the snugger near

the rear and move it back and forth to fit your

needs.

Not all features are on all models.

Refrigerator bin

Freezer tilt-out bin

Snugger

Freezer bin

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows you to

reach items stored behind others. The special

edges are designed to help prevent spills from

dripping to lower shelves.

To remove:

Slide the shelf out until it reaches the stop,

then press down on the tab and slide the shelf

straight out.

Press tab and pull shelf

forward to remove

To replace or relocate:

Line the shelf up with the supports and slide it

into place. The shelf can be repositioned when

the door is at 90° or more. To reposition the

shelf, slide the shelf past the stops and angle

downward. Slide shelf down to the desired

position, line up with the supports and slide into

place.

Make sure you push the shelves all the way

back in before you close the door.

Top freezer bin

CAUTION:

Be careful when

placing items in

the top bin. Make

sure that items do

not block or fall

into the ice chute.

Freezer Baskets (on some models)

To remove, slide out to the stop position, lift the

front past the stop position, and slide out.

Make sure you push the baskets all the way

back in before you close the door.

Freezer Baskets (on some models)

To remove, push the basket all the way to the

back of the freezer. Lift up until the back pins

are disengaged. Lift the entire basket up and

pull out.

Make sure you push the baskets all the way

back in before you close the door.

9

About the shelves and bins.

GEAppliances.com

Not all features are on all models.

QuickSpace™ Shelf (on some models)

This shelf splits in half and slides under itself for

storage of tall items on the shelf below.

This shelf can be removed and replaced or

relocated just like Slide-Out Spillproof Shelves.

On some models, this shelf can not be used in

the lowest position.

Slide-Out Freezer Shelves

To remove, slide out to the stop position, lift the

front past the stop position, and slide out from

rib.

Make sure you push the shelves all the way

back in before you close the door.

Fixed Freezer Shelves

To remove, lift the shelf up at the left side and

then bring the shelf out.

NOTE FOR DISPENSER MODELS: In order to

take full advantage of the tilt-out ice bin (on

some models), only store items on the shelf

below the ice bin that are no taller than the

lowest point on the bin.

Door Wine/Beverage Rack

(on some models)

This rack holds up to 5 cans, one bottle of

wine or one 2-liter bottle of soda.

The rack hangs from the sides of the dairy bin.

To remove:

Empty the wine/beverage rack.

Holding the bottom of the dairy bin, lift the

front straight up, then lift up and out.

To detach the rack from the dairy bin, pull

the rack’s side wires out of the holes on

each side of the dairy bin.

ShelfSaver

™

Rack

(on some models)

Use this rack to store

beverage cans for easy

access.

It can also hold a 9” x 13”

baking dish.

Door Can Rack

(on some models)

Removable Beverage Rack

(on some models)

The beverage rack is designed to

hold a bottle on its side. It can be

attached to any slide-out shelf.

1

2

This door rack holds up to 9 cans.

NOTE: This rack can only be

mounted in the top position under

the dairy bin.

To replace:

Reattach the rack to the sides of the bin.

Engage the back side of the bin in the

molded supports on the door. Then push

down on the front of the bin. The bin will

lock into place.

To install:

Line up the large part of the

slots on the top of the rack with

the tabs under the shelf.

Then slide the rack back to lock

it in place.

10

About the refrigerator doors.

Refrigerator Doors

(on some models)

The refrigerator doors may feel different

than the ones you are used to. The special

door opening/closing feature makes sure

the doors close all the way and are securely

sealed.

When opening and closing the door you will

notice a stop position. If the door is opened

past this stop point, the door will remain

open to allow you to load and unload food

more easily. When the door is only partially

open, it will automatically close.

The resistance you feel at the stop position

will be reduced as the door is loaded with

food.

When the door is only partially

open, it will automatically close.

Beyond this stop the door will stay

open.

Door Alignment

If doors are uneven, adjust the refrigerator

door.

Using a 7/16” socket wrench, turn the

door adjusting screw to the right to raise

the door; to the left, to lower it. (A nylon

plug, imbedded in the threads of the pin,

prevents the pin from turning unless a

wrench is used.)

After one or two turns of the wrench,

open and close the refrigerator door

and check the alignment at the top of

the doors.

To remove the base

grille, open the doors,

remove the screw at

each end of the base

grille and then pull

the grille straight out.

7/16” Socket Wrench

Raise

About crisper removal.

Not all features are on all models.

Crisper Removal

Crispers can easily be removed by pulling the

drawer straight out and lifting the drawer up

and over the stop location.

If the door prevents you from taking out the

drawers, first try to remove the door bins.

If this does not offer enough clearance, the

refrigerator will need to be rolled forward

until the door opens enough to slide the

drawers out. In some cases, when you roll the

refrigerator out, you will need to move the

refrigerator to the left or right as you roll it out.

11

About the crispers and pans. GEAppliances.com

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that may accumulate in the

bottom of the drawers should be wiped dry.

On some models, the bottom drawer has full

extension slides that allow full access to the

drawer.

Adjustable Humidity Crispers

Slide the control all the way to the HI setting to

provide high humidity recommended for most

vegetables.

Slide the control all the way to the LO setting to

provide lower humidity levels recommended for

most fruits.

HI

LO

Convertible Deli Pan (on some models)

The convertible deli pan has its own cold

air duct to allow a stream of cold air from

the freezer compartment or refrigerator

compartment to flow to the pan.

The variable temperature control regulates the

air flow from the Climate Keeper.

Set the control to the coldest setting to store

fresh meats.

Set the control to cold to convert the panto

normal refrigerator temperature and provide

extra vegetable storage space. The cold air

duct is turned off. Variable settings between

these extremes can be selected.

C

O

L

D

C

O

L

D

E

S

T

12

About the automatic icemaker.

Automatic Icemaker

7KHLFHPDNHUZLOOSURGXFHVHYHQFXEHVSHUF\FOH³

approximately 100–130 cubes in a 24-hour period, depending

on freezer compartment temperature, room temperature,

number of door openings and other use conditions.

If the refrigerator is operated before the water connection is

made to the icemaker, set the power switch in the OFF position.

When the refrigerator has been connected to the water supply,

set the power switch to the ON position.

The icemaker will fill with water when it cools to 15°F (–10°C).

A newly installed refrigerator may take 12 to 24 hours to begin

making ice cubes.

You will hear a buzzing sound each time the icemaker fills with

water.

Throw away the first few batches of ice to allow the water line

to clear.

Be sure nothing interferes with the sweep of the feeler arm.

When the bin fills to the level of the feeler arm, the icemaker will

stop producing ice. It is normal for several cubes to be joined

together.

If ice is not used frequently, old ice cubes will become cloudy,

taste stale and shrink.

Special note about dispenser models:

 Some models have a tilt-out ice bin. The bin can be tilted

out as shown in the illustrations, and it will hold itself up

while you take ice out or turn the icemaker power switch on

and off. Be sure to put the bin back in place before closing

the door.

 To restore your ice level from an empty bucket stage, the

following steps are recommended:

12 hours after the first batch of ice has fallen into the bin,

dispense 3 to 4 cubes.

After an additional 6 hours, dispense 3 to 4 cubes again.

These steps will restore your ice level in the shortest amount of

time.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Icemaker

Feeler Arm

Power

Switch

(on some models)

Icemaker

Feeler Arm

Power

Switch

Green

Power Light

(on some models)

NOTE:

In homes with lower than average water pressure,

you may hear the icemaker cycle multiple times

when making one batch of ice.

13

Removing Ice Bin (dispenser models)

CAUTION: The ice bin is heavy when full.

Set the power switch to the OFF position before removing the

bin.

When replacing the bin, be sure to press it firmly into place. If

it does not go all the way back, remove it and rotate the drive

mechanism 1/4 turn. Then push the bin back again.

Rotate

Drive

Mechanism

Dispenser Models only

Lift the bin, then pull it forward

until the bin stops.

Lower the bin to access ice or

reach the power switch.

Models with tilt out ice bin

To access ice and reach the icemaker power switch:

Accessing Ice and Reaching the Power Switch on

Dispenser Models

There are two types of ice storage bins on dispenser models.

One has a shelf above the bin, the other does not.

Special note for models with tilt-out ice bin:

 These models have a tilt-out ice bin. The bin can be tilted

out as shown in the illustrations, and it will hold itself up

while you take ice out or turn the icemaker power switch

on and off. Be sure to put the bin back in place before

closing the door.

NOTE: In order to take full advantage of the tilt-out ice bin, only store items

on the shelf below the ice bin that are no taller than the lowest point on the

bin.

To access ice, pull the bin forward.

To reach the power switch, pull the

shelf straight out. Always be sure to

replace the shelf.

Models with a shelf above the ice bin

Shelf

Ice Bin

Shelf

Ice Bin

About the automatic icemaker. (cont) GEAppliances.com

Pull the bin forward until the

bin stops.

Lower the bin to access ice or

reach the power switch.

On some models, to access ice or reach the power switch:

14

About the ice and water dispenser. (on some models)

To Use the Dispenser

Select CUBED ICE , CRUSHED ICE

or WATER .

Press the glass gently against the top of the

dispenser cradle.

The spill shelf is not self-draining. To reduce

water spotting, the shelf and its grille should be

cleaned regularly.

If no water is dispensed when the

refrigerator is first installed, there may be air

in the water line system. Press the dispenser

arm for at least two minutes to remove

trapped air from the water line and to fill the

water system. To flush out impurities in the

water line, throw away the first six glassfuls

of water.

CAUTION: Never put fingers or any other

objects into the ice crusher discharge

opening.

Locking the Dispenser

Press the LOCK pad for

3 seconds to lock the

dispenser and control

panel. To unlock, press and

hold the pad again for 3

seconds.

Dispenser Light

This pad turns the night

light in the dispenser on and

off. The light also comes on

when the dispenser cradle is

pressed. For models with a

bulb, if the light burns out, it

should be replaced with a 6

watt 12V maximum bulb. For

LED models, contact Factory

Service.

Quick Ice (on some models)

When you need ice in a

hurry, press this pad to speed

up ice production. This will

increase ice production for

the following 48 hours or until

you press the pad again.

Door Alarm (on some

models)

To set the alarm, press this

pad until the indicator light

comes on. This alarm will

sound if either door is open

for more than 3 minutes.

The light goes out and the

beeping stops when you

close the door.

Spill Shelf

Important Facts About Your Dispenser

 Do not add ice from trays or bags to the

storage drawer. It may not crush or dispense

well.

 Avoid overfilling glass with ice and use of

narrow glasses. Backed-up ice can jam

the chute or cause the door in the chute to

freeze shut. If ice is blocking the chute, poke it

through with a wooden spoon.

 Beverages and foods should not be quick-

chilled in the ice storage drawer. Cans,

bottles or food packages in the storage

drawer may cause the icemaker or auger to

jam.

 To keep dispensed ice from missing the

glass, put the glass close to, but not touching,

the dispenser opening.

 Some crushed ice may be dispensed

even though you selected CUBED ICE. This

happens occasionally when a few cubes

accidentally get directed to the crusher.

 After crushed ice is dispensed, some water

may drip from the chute.

 Sometimes a small mound of snow will form

on the door in the ice chute. This condition is

normal and usually occurs when you have

dispensed crushed ice repeatedly. The snow

will eventually evaporate.

15

Care and cleaning of the refrigerator. GEAppliances.com

Cleaning the Outside

The dispenser drip area, beneath the grille,

should be wiped dry. Water left in this area may

leave deposits. Remove the deposits by adding

undiluted vinegar to the well. Soak until the

deposits disappear or become loose enough to

rinse away.

The dispenser cradle. Before cleaning, lock the

dispenser by pressing and holding the LOCK

pad for 3 seconds. Clean with warm water and

EDNLQJVRGDVROXWLRQ³DERXWDWDEOHVSRRQ

ml) of baking soda to a quart (1 liter) of water.

Rinse thoroughly and wipe dry.

The door handles and trim. Clean with a cloth

dampened with soapy water. Dry with a soft

cloth.

The stainless steel panels and door handles

(on some models) can be cleaned with a

commercially available stainless steel cleaner. A

spray-on stainless steel cleaner works best.

Do not use appliance wax or polish on the

stainless steel.

Keep the outside clean. Wipe with a clean cloth

lightly dampened with kitchen appliance wax or

mild liquid dish detergent. Dry and polish with a

clean, soft cloth.

Do not wipe the refrigerator with a soiled dish

cloth or wet towel. These may leave a residue

that can erode the paint. Do not use scouring

pads, powdered cleaners, bleach or cleaners

containing bleach because these products

can scratch and weaken the paint finish.

Cleaning the Inside

To help prevent odors, leave an open box

of baking soda in the fresh food and freezer

compartments.

Unplug the refrigerator before cleaning. If

this is not practical, wring excess moisture

out of sponge or cloth when cleaning around

switches, lights or controls.

8VHZDUPZDWHUDQGEDNLQJVRGDVROXWLRQ³

about a tablespoon (15 ml) of baking soda to

a quart (1 liter) of water. This both cleans and

neutralizes odors. Rinse and wipe dry.

Use of any cleaning solution other than that

which is recommended, especially those that

contain petroleum distillates, can crack or

damage the interior of the refrigerator.

Avoid cleaning cold glass shelves with hot

water because the extreme temperature

difference may cause them to break. Handle

glass shelves carefully. Bumping tempered

glass can cause it to shatter.

Do not wash any plastic refrigerator parts in

the dishwasher.

The chill/thaw tray is dishwasher safe.

Dispenser drip area.

16

Replacing the light bulbs. (on some models)

Note: Turning the refrigerator off via the controls on the touch panel does not shut off electrical power to the refrigerator.

5HIULJHUDWRU&RPSDUWPHQW³8SSHU/LJKW

Unplug the refrigerator.

The bulbs are located at the top of the

compartment, inside the light shield. On

some models, a screw at the front of the

light shield will have to be removed. On

other models, the screw is located in the

pocket located at the back of the shield.

To remove the light shield, on some models,

press in on the tabs on the sides of the

shield and slide forward and out. On other

models, just slide the shield forward and

out.

After replacing the bulb with an appliance

bulb of the same or lower wattage, replace

the light shield and screw. When replacing

the light shield, make sure that the tabs at

the back of the shield fit into the slots at the

back of the light shield housing.

Plug the refrigerator back in.

Tabs

Your light shield will look like

one of the following:

Pocket

OR

For long vacations or absences, remove food

and unplug the refrigerator. Clean the interior

with a baking soda solution of one tablespoon

(15 ml) of baking soda to one quart (1 liter) of

water. Leave the doors open.

Set the icemaker power switch to the OFF

position and shut off the water supply to the

refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water supply

system (on some models) to prevent serious

property damage due to flooding.

Care and cleaning of the refrigerator. (cont.)

Behind the Refrigerator

Be careful when moving the refrigerator away

from the wall. All types of floor coverings can

be damaged, particularly cushioned coverings

and those with embossed surfaces.

Pull the refrigerator straight out and return it

to position by pushing it straight in. Moving the

refrigerator in a side direction may result in

damage to the floor covering or refrigerator.

When pushing the refrigerator back, make

sure you don’t roll over the power cord or

icemaker supply line (on some models).

Preparing for Vacation

Preparing to Move

Secure all loose items such as shelves and

drawers by taping them securely in place to

prevent damage.

When using a hand truck to move the

refrigerator, do not rest the front or back of the

refrigerator against the hand truck. This could

damage the refrigerator. Handle only from the

sides of the refrigerator.

Be sure the refrigerator stays in an upright

position during moving.

17

Replacing the lights on models with LED lighting

Setting the controls to OFF does not remove power to the light circuit. Not all features are on all models.

Refrigerator Compartment (on some models)

There is an LED lighting display in the top and sides of the fresh food compartment and in the rear

and side of the freezer compartment on some models.

If this assembly needs to be replaced, call GE Service at 1.800.432.2737 in the United States or

1.800.561.3344 in Canada.

LED

Lighting

Display

5HIULJHUDWRU&RPSDUWPHQW³/RZHU/LJKW

This light is located above the top drawer.

Unplug the refrigerator.

Lift the light shield up and pull it out.

After replacing the bulb with an appliance

bulb of the same or lower wattage, replace

the shield.

Plug the refrigerator back in.

Freezer Compartment

Unplug the refrigerator.

Remove the shelf just above the light shield.

(The shelf will be easier to remove if it is

emptied first.) Remove the screw at the top

of the light shield.

To remove the light shield, press in on the

sides, and lift up and out.

Replace the bulb with an appliance bulb

of the same or lower wattage, and

reinstall the light shield. When reinstalling

the light shield, make sure the top tabs

snap securely into place. Replace the

screw.

Reinstall the shelf and plug the

refrigerator back in.

Dispenser (on some models)

Unplug the refrigerator.

The bulb is located on the dispenser under

the control panel. Remove the light bulb by

turning it counterclockwise.

Replace the bulb with a bulb of the same

size and wattage.

Plug the refrigerator back in.

Replacing the light bulbs. (cont) GEAppliances.com

18

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT ³6DYHWKHVHLQVWUXFWLRQVIRU

local inspector’s use.

•

IMPORTANT ³2EVHUYHDOOJRYHUQLQJ

codes and ordinances.

•

Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time –

Refrigerator Installation

30 minutes

Water Line Installation

30 minutes

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

If the refrigerator has already been installed, remove

the base grille (see Step 2 in Moving the Refrigerator),

then skip to Step 5 in Installing the Refrigerator.

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com

In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca

Installation

Refrigerator

Instructions

Models 22, 23, 25, 26, 27 & 29

If the refrigerator has an icemaker, it will have to be

connected to a cold water line. A GE water supply

kit (containing tubing, shutoff valve, fittings and

instructions) is available at extra cost from your

dealer, by visiting our Website at GEAppliances.

com (in Canada at www.geappliances.ca) or from

Parts and Accessories, 800.626.2002 (in Canada

1.800.661.1616).

PREPARATION

WATER SUPPLY TO THE ICEMAKER

TOOLS YOU WILL NEED

Phillips Head Screwdriver

3/8” and 5/16” Socket 1/2” and 7/16” Wrench

Plastic Putty Knife

19

Installation Instructions

LOADING THE REFRIGERATOR

ONTO A HAND TRUCK

Leave all tape and door pads on doors until the

refrigerator is in its final location.

To move the refrigerator, use a padded hand

truck. Center the refrigerator on the hand truck

and secure the strap around the refrigerator.

DO NOT OVERTIGHTEN THE STRAP.

1

REMOVE THE BASE GRILLE

Remove the grille by removing the two

Phillips head screws.

2

If the refrigerator must go through any

entrance that is less than 38” wide, the

doors must be removed. Proceed to

Step 3.

DO NOT remove the handles.

If all entrances are more than 38” wide,

skip to Installing the Refrigerator.

DISCONNECT THE WATER COUPLING

(on some models)

If the refrigerator has a water dispenser,

there is a water line from the cabinet into the

bottom hinge on the freezer door that must be

disconnected.

To disconnect, push in on the white collar of

the coupling and pull out the tubing.

3

White collar

Bottom

freezer

hinge

MOVING THE REFRIGERATOR

20

REMOVE THE FREEZER DOOR

Remove the freezer door top hinge cover (if

equipped) by either squeezing it and pulling it

up or by prying it off with a plastic putty knife.

Remove the two 5/16” hex head screws, then

lift the hinge straight up to free the hinge pin.

Open the freezer door to 90.°

Installation Instructions

DISCONNECT THE POWER COUPLING

(on some models)

If the refrigerator has a water dispenser,

there is a power line (harness) from the cabinet

into the bottom hinge on the freezer door that

must be disconnected.

To disconnect, pull apart at the coupling.

4

Bottom

freezer

hinge

DISCONNECT THE ELECTRICAL

CONNECTORS (on some models)

If the refrigerator has a refreshment center,

there are electrical connectors (harnesses)

from the cabinet into the bottom hinge on the

refrigerator door that must be disconnected.

To disconnect, pull apart each connector.

5

Bottom

refrigerator

hinge

CLOSE THE FREEZER AND

REFRIGERATOR DOORS

6

7

A

C

B

5/16” Hex Head

90°

MOVING THE REFRIGERATOR (CONT.)

La page charge ...

GE Appliances GSE25HSHSS Guide d'installation

GE Appliances GSE25HSHSS Guide d'installation

dans d''autres langues

Documents connexes

Autres documents