Hilti TE 6-A22 Mode d'emploi

TE 6-A22

English 1

Français 12

Español 24

Português 36

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

TE 6-A22

en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

fr Notice d'utilisation originale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

es Manual de instrucciones original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

pt Manual de instruções original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

*2166239*

2166239 English 1

Original operating instructions

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free

handling and use of the product.

• Observe the safety instructions and warnings in this documentation and on the product.

• Always keep the operating instructions with the product and make sure that the operating instructions

are with the product when it is given to other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶ Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶ Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶ Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage

to the equipment or other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use.

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

These numbers refer to the corresponding illustrations found at the beginning of these operating

instructions

The numbering reflects the sequence of operations shown in the illustrations and may deviate

from the steps described in the text

Item reference numbers are used in the overview illustrations and refer to the numbers used in

the product overview section

This symbol is intended to draw special attention to certain points when handling the product.

2 English 2166239

*2166239*

1.3 Product-dependent symbols

1.3.1 Symbols

The following symbols can be used on the product:

Drilling without hammer action

Drilling with hammering action (hammer drilling)

Chiseling

Chisel positioning

Forward / reverse

Rated speed under no load

Direct current (DC)

Li-ion battery

Hilti Li-ion battery type series used. Observe the information given in the section headed In-

tended use.

Never use the battery as a striking tool.

Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any

other way.

The power tool supports near-field communication (NFC) technology, which is compatible with

iOS and Android platforms.

1.4 Product information

products are designed for professional users and only trained, authorized personnel are

permitted to operate, service and maintain the products. This personnel must be specifically informed about

the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by

untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are printed on the rating plate.

▶ Write down the serial number in the table below. You will be required to state the product details when

contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Rotary hammer TE 6A22

Generation 04

Serial no.

1.5 Declaration of conformity

We declare, on our sole responsibility, that the product described here complies with the applicable directives

and standards. A copy of the declaration issued by the certification department can be found at the end of

this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING

Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

*2166239*

2166239 English 3

Work area safety

▶ Keep work area clean and well lit. Cluttered or dark areas invite accidents.

▶ Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

▶ Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

Electrical safety

▶ Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

▶ Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

Personal safety

▶ Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

▶ Use personal protective equipment. Always wear eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce

personal injuries.

▶ Prevent unintentional starting. Ensure the switch is in the off‐position before connecting to battery

pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising

power tools that have the switch on invites accidents.

▶ Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

▶ Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

▶ Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

▶ If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used. Use of dust collection can reduce dust-related hazards.

Power tool use and care

▶ Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

▶ Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

▶ Disconnect the battery pack from the power tool before making any adjustments, changing

accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the

power tool accidentally.

▶ Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

▶ Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and

any other condition that may affect the power tool’s operation. If damaged, have the power tool

repaired before use. Many accidents are caused by poorly maintained power tools.

▶ Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

▶ Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

Battery tool use and care

▶ Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with another battery pack.

▶

Use power tools only with specifically designated battery packs. Use of any other battery packs may

create a risk of injury and fire.

▶ When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a fire.

▶ Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

4 English 2166239

*2166239*

Service

▶ Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

2.2 Hammer safety warnings

▶ Wear ear protectors. Exposure to noise can cause hearing loss.

▶ Use auxiliary handles, if supplied with the tool. Loss of control can cause personal injury.

▶ Hold power tool by insulated gripping surfaces, when performing an operation where the cutting

accessory may contact hidden wiring.. Cutting accessory contacting a "live" wire may make exposed

metal parts of the power tool "live" and could give the operator an electric shock.

2.3 Additional safety instructions for rotary hammer

Personal safety

▶ Use the product only when it is in technically faultless condition.

▶ Never tamper with or modify the power tool in any way.

▶ Use the auxiliary grips supplied with the tool. Loss of control can cause personal injury.

▶ Apply appropriate safety measures at the opposite side of the workpiece in work that involves breaking

through. Parts breaking away could fall out and / or fall down causing injury to other persons.

▶ Always hold the power tool with both hands on the grips provided. Keep the grips clean and dry.

▶ Hold the power tool by the insulated gripping surfaces when performing work in which the accessory

tool might come into contact with concealed wiring. If the accessory tool comes into contact with a live

wire, metal parts of the power tool can also become live, resulting in an electric shock.

▶ Avoid touching rotating parts – risk of injury!

▶ Wear suitable protective glasses, a hard hat, ear defenders, protective gloves and light respiratory

protection while using the power tool.

▶ Wear protective gloves also when changing the accessory tool. Touching the accessory tool presents a

risk of injury (cuts or burns).

▶ Wear eye protection. Flying fragments present a risk of injury to the body and eyes.

▶ Before starting work, check the hazard class of the dust that will be produced when working. Use

an industrial vacuum cleaner with an officially approved protection class in compliance with the locally

applicable dust protection regulations. Dust from materials such as lead-based paint, certain types of

wood and concrete/masonry/stone containing quartz, minerals or metal can be harmful to health.

▶ Make sure that the workplace is well ventilated and, where necessary, wear a respirator appropriate for

the type of dust generated. Contact with or inhalation of the dust can cause allergic reactions and/or

respiratory or other diseases to the operator or bystanders. Certain kinds of dust such as oakwood

and beechwood dust are classified as carcinogenic, especially in conjunction with additives for wood

conditioning (chromate, wood preservative). Only specialists are permitted to handle material containing

asbestos.

▶ Take breaks and do physical exercises to improve the blood circulation in your fingers. Exposure to

vibration during long periods of work can lead to disorders of the blood vessels and nervous system in

the fingers, hands and wrists.

Electrical safety

▶ Before beginning work, check the working area for concealed electric cables, gas pipes and water

pipes. External metal parts of the power tool can become live, presenting a risk of electric shock, if you

accidentally damage an electric cable.

Power tool use and care

▶ Immediately switch off the power tool if the accessory tool jams. The power tool might twist off-line.

▶ Wait until the power tool stops completely before you lay it down.

2.4 Safety instructions for dust removal module

▶ Observe all safety instructions in this documentation and on the device.

▶ Use respiratory protection to keep residual dust away from the face and airways when drilling and when

servicing the tool or accessories.

▶ Always use the side handle on the Hilti rotary hammer drill, even when the dust removal module is fitted.

*2166239*

2166239 English 5

2.5 Battery use and care

▶ Observe the special regulations and instructions applicable to the transport, storage and use of Li-ion

batteries.

▶ Do not expose batteries to high temperatures, direct sunlight or fire.

▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C.

▶ Do not use or charge batteries that have suffered mechanical impact, have been dropped from a height

or show signs of damage. In this case, always contact your Hilti Service.

▶ If the battery is too hot to touch it may be defective. In this case, place the product in a non-flammable

location, well away from flammable materials, where it can be kept under observation and allowed to

cool down. In this case, always contact your Hilti Service.

3 Description

3.1 Overview of the product 1

@

Dust shield

;

chuck

=

Insert tool unlocking device

%

Depth gauge

&

Function selector switch

(

Forward / reverse selector switch with safety

lock

)

Control switch

+

Grip

§

Battery release buttons

/

Charge status and fault display (Li-ion bat-

tery)

:

Battery

∙

Connection for the TE DRS-6-A(02) dust re-

moval module

$

Side handle

£

Light to illuminate the work area

3.2 Intended use

The product described is a cordless rotary hammer drill. It is designed for drilling in steel, wood and masonry,

for hammer-action drilling in concrete and masonry, and for driving and removing screws. The product can

also be used for light chiseling work on masonry and surface finishing on concrete.

▶ Use only Hilti lithiumion batteries of the B 22 series with this product.

▶ Use only the Hilti lithium-ion batteries from the B22 series for this product.

3.3 Lithiumion battery status display

The charge status of the Li-ion battery and malfunctions of the power tool are indicated by the display on

the Liion battery. The charge status of the Liion battery is displayed after pressing one of the two battery

release buttons.

Status Meaning

4 LEDs light up. Charge status: 75 % to 100 %

6 English 2166239

*2166239*

Status Meaning

3 LEDs light up. Charge status: 50 % to 75 %

2 LEDs light up. Charge status: 25 % to 50 %

1 LED lights up. Charge status: 10 % to 25 %

1 LED blinks. Charge status: < 10 %

Battery charge status cannot be displayed while the control switch is pressed and for up to 5 seconds

after releasing the control switch. If the battery display LEDs blink, please observe the instructions

given in the Troubleshooting section.

3.4 Items supplied

Rotary hammer, side handle, depth gauge, operating instructions.

You can find other system products approved for your product at your local Hilti Center or online at:

www.hilti.com.

4 Technical data

4.1 Rotary hammer

TE 6A22

Rated voltage

21.6 V

Weight including battery B22⁄8.0

8.4 lb

(3.8 kg)

Rated speed under no load

1,050 /min

Single impact energy

2.5 J

Drilling diameter range in concrete/masonry (hammer drilling)

0.2 in … 0.8 in

Drilling diameter range in concrete/masonry (hammer drilling)

5 mm … 20 mm

Drilling diameter range in wood (solid)

0.1 in … 0.8 in

Drilling diameter range in wood (solid)

3 mm … 20 mm

Drilling diameter range in metal (solid-head drill bit)

0.1 in … 0.5 in

Drilling diameter range in metal (solid-head drill bit)

3 mm … 13 mm

4.2 Battery

Battery operating voltage

21.6 V

Ambient temperature for operation

1 ℉ … 140 ℉

(−17 ℃ … 60 ℃)

Storage temperature

−4 ℉ … 104 ℉

(−20 ℃ … 40 ℃)

Battery charging starting temperature

14 ℉ … 113 ℉

(−10 ℃ … 45 ℃)

5 Operation

5.1 Preparations at the workplace

CAUTION

Risk of injury by inadvertent starting!

▶ Before inserting the battery, make sure that the product is switched off.

▶ Remove the battery before making any adjustments to the power tool or before changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

*2166239*

2166239 English 7

5.2 Inserting the battery 2

CAUTION

Risk of injury! Inadvertent starting of the rotary hammer drill.

▶ Before installing the battery, check that the rotary hammer drill is switched off and that the forward/reverse

switch is in the middle position (i.e. safety lock engaged).

1. Push the battery into the battery holder until it engages with an audible click.

2. Check that the battery is seated securely.

5.3 Removing the battery 3

1. Press the release buttons on the battery.

2. Pull the battery out toward the rear.

5.4 Fitting the side handle 4

CAUTION

Risk of injury! Loss of control over the rotary hammer drill.

▶ Check that the side handle is fitted correctly and tightened securely. Check that the clamping band is

engaged in the groove in the tool.

1. Release the side handle clamping band by turning the handle grip.

2. From the front, slide the depth gauge into the 2 guide holes.

3. Tighten the side handle clamping band by turning the handle grip.

5.5 Fitting and adjusting the depth gauge 5

▶ Fit the depth gauge, if necessary, and adjust it correctly.

5.6 Fitting / removing the chuck 6

CAUTION

Risk of injury! The depth gauge, if fitted but not used, might hinder the operator.

▶ Remove the depth gauge from the tool.

▶ Fit / remove the chuck.

5.7 Inserting the tool 7

1. Lightly grease the connection end of the accessory tool.

▶ Use only genuine Hilti grease. Using the wrong grease can result in damage to the tool.

2. Push the accessory tool into the chuck as far as it will go (until it engages).

3. After fitting the accessory tool, grip it and pull it in order to check that it is securely engaged.

▶ The product is ready for use.

5.8 Removing the accessory tool 8

▶ Pull the chuck back as far as it will go and remove the accessory tool.

5.9 Overhead work 9

▶ Fit the DCD dust control ring for overhead work.

5.10 Chisel positioning 10

▶

Set the function selector switch to the position.

8 English 2166239

*2166239*

6 Types of work

ATTENTION

Risk of damage by incorrect handling!

▶ Do not operate the switches for direction of rotation and/or function selection during operation.

Observe the safety instructions and warnings in this documentation and on the product.

6.1 Function selector switch 10

▶ Set the function selector switch to the desired working position.

▶

Do not operate the function selector switch while the motor is running. Risk of damage!

6.2 Forward/reverse 11

▶ Set the forward/reverse switch to the desired direction of rotation.

6.3 Drilling without hammer action

▶

Set the function selector switch to the position.

6.4 Drilling with hammer action

▶

Set the function selector switch to the position.

6.5 Chiseling

▶

Set the function selector switch to the position.

▶ For optimum motor cooling, select the forward direction, i.e. clockwise (direction of rotation for

drilling).

7 Care and maintenance

7.1 Care and maintenance

WARNING

Risk of injury with battery inserted !

▶ Always remove the battery before carrying out care and maintenance tasks!

Care and maintenance of the tool

• Carefully remove stubborn dirt.

• Clean the air vents carefully with a dry brush.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

Care of the Liion batteries

• Keep the battery free from oil and grease.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

these may attack the plastic parts.

• Avoid ingress of moisture.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all

function correctly.

• Do not operate the product if signs of damage are found or if parts malfunction. Have it repaired

immediately by Hilti Service.

• After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with the product can be found at your

local Hilti Store or online at: www.hilti.group.

*2166239*

2166239 English 9

7.2 Cleaning the dust shield

▶ Clean the dust shield on the chuck with a dry, clean cloth at regular intervals.

▶ Clean the sealing lip by wiping it carefully and then grease it again lightly with Hilti grease.

▶ It is essential that the dust shield is replaced if the sealing lip is damaged.

8 Transport and storage

8.1 Transport and storage of cordless tools

Transport

CAUTION

Accidental starting during transport !

▶ Always transport your products with the batteries removed!

▶ Remove the battery.

▶ Never transport batteries in bulk form (loose, unprotected).

▶ Check the tool and batteries for damage before use after long periods of transport.

Storage

CAUTION

Accidental damage caused by defective or leaking batteries !

▶ Always store your products with the batteries removed!

▶ Store the tool and batteries in a place that is as cool and dry as possible.

▶ Never store batteries in direct sunlight, on heating units or behind a window pane.

▶ Store the tool and batteries in a place where they cannot be accessed by children or unauthorized

persons.

▶ Check the tool and batteries for damage before use after long periods of storage.

9 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by

yourself, please contact Hilti Service.

9.1 The rotary hammer is not in working order

Malfunction Possible cause Action to be taken

The LEDs on the battery indi-

cate nothing.

The battery is not fully inserted. ▶ Push the battery in until it

engages with a double click.

The battery is discharged. ▶ Change the battery and charge

the empty battery.

The battery is too hot or too cold. ▶ Allow the battery to cool

down or to warm up to room

temperature.

1 LED on the battery blinks. The battery is discharged. ▶ Change the battery and charge

the empty battery.

The battery is too hot or too cold. ▶ Allow the battery to cool

down or to warm up to room

temperature.

4 LEDs on the battery blink. The rotary hammer has been over-

loaded briefly.

▶ Release the control switch and

then press it again.

10 English 2166239

*2166239*

9.2 The rotary hammer is in working order

Trouble or fault Possible cause Action to be taken

No hammering action. The rotary hammer is too cold. ▶ Bring the tip of the drill bit

into contact with the working

surface, switch the rotary

hammer on and allow it to

run. If necessary, repeat the

procedure until the hammering

mechanism begins to operate.

The function selector switch is set

to “Drilling without hammering” .

▶ Set the function selector switch

to “Hammer drilling” .

The control switch can’t be

pressed, i.e. the switch is

locked.

The forward / reverse switch is in

the middle position.

▶ Push the forward / reverse

switch to the right or left.

The drive spindle does not

rotate.

The permissible operating temper-

ature of the rotary hammer’s elec-

tronics has been exceeded.

▶ Allow the tool to cool down.

The battery is discharged. ▶ Change the battery and charge

the empty battery.

The function selector switch is

not correctly engaged, is set to

“Chiseling” , or is set to “Chisel

positioning” .

▶ Set the function selector switch

to “Drilling without hammering”

or “Hammer drilling” .

The rotary hammer switches

itself off automatically.

The overload cut-out has been

activated.

▶ Release the control switch.

Allow the rotary hammer to cool

down. Press the control switch

again. Reduce the load on the

tool.

The battery runs down more

quickly than usual.

Very low ambient temperature. ▶ Allow the battery to warm up

slowly to room temperature.

The battery does not en-

gage with an audible "double

click".

The retaining lugs on the battery

are dirty.

▶ Clean the retaining lugs and refit

the battery.

The rotary hammer or the

battery gets very hot.

Electrical fault. ▶ Switch off the rotary hammer

immediately. Remove the

battery and keep it under

observation. Allow it to cool

down. Contact Hilti service.

The rotary hammer has been over-

loaded.

▶ Use a more powerful tool.

The insert tool can’t be re-

leased.

The chuck is not pulled back fully. ▶ Pull the chuck back as far as it

will go and remove the tool.

The tool makes no progress. The rotary hammer has been set to

reverse rotation.

▶ Move the forward / reverse

selector switch to the “Forward”

position.

The function selector switch is set

to “Drilling without hammering” .

▶ Set the function selector switch

to “Hammer drilling” .

10 Optional accessories

10.1 DCD dust control ring

The DCD dust control ring is an accessory for Hilti rotary hammer drills. It collects a high percentage of the

dust produced by overhead work and it attaches quickly and easily to the rotary hammer drill.

*2166239*

2166239 English 11

10.2 TE DRS-6-A / TE DRS-6-A OSHA dust removal module

The TE DRS6A dust removal module is an accessory for the Hilti TE 6A22 rotary hammer drill. It collects

a high percentage of the dust and it attaches quickly and easily to the rotary hammer drill. The dust removal

module has a built-in extractor fan. This fan is driven by its own motor. When the rotary hammer drill is

switched on the dust removal module draws its electric power from the rotary hammer drill’s battery.

The dust removal module is not suitable for working on metal and wood.

Conditions: TE DRS-6-A OSHA

The TE DRS-6-A OSHA satisfies the requirements of OSHA 1926.1153 Table 1. It has a filter-cleaning

mechanism.

10.2.1 Fitting the dust removal module 12

Before fitting the module, check that the attachment points and the electrical interfaces on the rotary

hammer drill and dust removal module are free of dust and that the parts fit or move freely and easily.

1. Check the dust removal module for damage.

2. Check the ease of movement of the telescoping mechanism.

3. Set the forward / reverse switch on the rotary hammer drill to the middle position.

4. Remove the depth gauge from the side handle.

5. Position the dust removal module on the guides and from the front, push it on to the power tool until it

engages.

6. After fitting, check that the dust removal module is secure.

10.2.2 Drilling with the dust removal module

1. Start the dust removal module by pressing the control button on the rotary hammer drill.

2. Hold down the control button until full suction power is reached.

3. Position the suction head with the edge seated flat against the work surface.

4. Drill the hole and ease the product slowly out of the drilled hole in order to catch as much dust as

possible.

10.2.3 Emptying the dust box 13

Regular cleaning and emptying are necessary because a full dust box or a clogged filter can lead to

excessive dust formation.

Empty the dust box after drilling 8-10 holes (16 mm x 50 mm) (5/8 in x 2 in).

To minimize dust formation, carefully transfer the dust to a container with a tight-fitting lid.

1. Hold the power tool horizontal and allow it to run for a short time.

▶ This ensures that residual dust deposits in the dust removal module are drawn into the dust box.

2. Press and hold down the release button of the dust box.

3. Pull the dust box down and clear of the dust removal module.

4. Empty the dust box.

▶ Filter is clogged.

▶ Change the filter.

▶ Filter is free of dust.

5. Push the empty dust box back into the dust removal module from below until it engages.

10.2.4 Cleaning the TE-DRS-OSHA filter 14

Clean the filter after drilling 5 holes (16 mm x 50 mm) (1/2 in x 3 in).

▶ When suction power diminishes, slide the cleaning mechanism 5 times forward and back until it audibly

clicks on each slide.

10.2.5 Removing the dust removal module 15

1. Set the forward / reverse switch on the rotary hammer drill to the middle position.

12 Français 2166239

*2166239*

2. Press and hold down the DRS release button.

3. Pull the dust removal module forward and clear of the power tool.

11 Disposal

Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The

materials must be correctly separated before they can be recycled. In many countries, your old tools,

machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative

for further information.

Battery disposal

Improper disposal of batteries can result in health hazards from leaking gases or fluids.

▶ DO NOT send batteries through the mail!

▶ Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting.

▶ Dispose of your battery out of the reach of children.

▶ Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public

health and safety resources for disposal instructions.

▶ Do not dispose of power tools, electronic equipment or batteries as household waste!

12 Manufacturer’s warranty

▶ Please contact your local Hilti representative if you have questions about the warranty conditions.

Notice d'utilisation originale

1 Indications relatives à la documentation

1.1 À propos de cette documentation

• Lire intégralement la présente documentation avant la mise en service. C'est la condition préalablement

requise pour assurer la sécurité du travail et un maniement sans perturbations.

• Bien respecter les consignes de sécurité et les avertissements de la présente documentation ainsi que

celles figurant sur le produit.

• Toujours conserver le mode d'emploi à proximité du produit et uniquement le transmettre à des tiers

avec ce mode d'emploi.

1.2 Explication des symboles

1.2.1 Avertissements

Les avertissements attirent l'attention sur des dangers liés à l'utilisation du produit. Les termes de

signalisation suivants sont utilisés :

DANGER

DANGER !

▶ Pour un danger imminent qui peut entraîner de graves blessures corporelles ou la mort.

AVERTISSEMENT

AVERTISSEMENT !

▶ Pour un danger potentiel qui peut entraîner de graves blessures corporelles ou la mort.

ATTENTION

ATTENTION !

▶ Pour attirer l'attention sur une situation pouvant présenter des dangers entraînant des blessures

corporelles légères ou des dégâts matériels.

La page charge ...

Hilti TE 6-A22 Mode d'emploi

Hilti TE 6-A22 Mode d'emploi

dans d''autres langues

Documents connexes