DMP Electronics 1106 Guide d'installation

Marque
DMP Electronics
Modèle
1106
Catégorie
Lecteurs de contrôle d'accès
Taper
Guide d'installation
1106 WIRELESS UNIVERSAL
TRANSMITTER
Installation Guide
The 1106 Wireless Universal
Transmitter is a wireless, two-input
transmitter typically used for door
and window applications.
The 1106 provides a cover tamper,
magnetic reed switch, and an
on-board terminal block to allow for
external contact wiring.
Both sets of contacts, internal and
external, can be programmed to
operate at the same time. This
allows two independent zones to
operate from one 1106.
The 1106 also features
Disarm/Disable functionality. When
this option is set to YES, Zone
Tripped messages are disabled
when the system is disarmed to
allow for extended transmitter
battery life. Supervision, Tamper,
and Low Battery are the only
messages that are sent to the panel
when the system is disarmed.
Compatibility
All DMP XTLplus
TM
, XT30/XT50, and
XR150/XR550 Series panels and all
1100 Series Wireless Receivers.
What is Included?
• One 1106 Wireless Universal
Transmitter
• One magnet in a one or
two-part housing
• One 3.0V lithium CR123A battery
• Hardware pack
• Double-sided tape
1
PROGRAM THE PANEL
Refer to the panel programming guide as needed.
1. In ZONE INFORMATION, enter the wireless ZONE NO: and
press CMD.
2. Enter the ZONE NAME and press CMD.
3. Select the ZONE TYPE and press CMD.
4. At the NEXT ZN? prompt, select NO.
5. Select YES when WIRELESS? displays.
6. Enter the eight-digit SERIAL# and press CMD.
7. At CONTACT, select either INTERNAL or EXTERNAL.
Note: Use consecutive zone numbers if using both internal
and external contacts.
8. If EXTERNAL was chosen in Step 7, choose NO or YES at
the NORM OPEN prompt.
9. Enter the SUPRVSN TIME and press CMD.
10. At DISARM DISABLE, select NO or YES.
11. At the NEXT ZN? prompt, select YES to finish programming
or select NO for additional programming options.
2
Figure 1: 1106 Housing
INSTALL THE BATTERY
Use a 3.0V lithium battery, a DMP Model CR123 battery, or an
equivalent model from Sony or Murata. For listed installations, use
either an Energizer® 123 battery or a CR123A battery manufactured
by Panasonic or Tekcell. Keep in mind, when setting up a wireless
system, program zones and connect the wireless receiver before
installing the battery.
1. Open the 1106 by inserting a 1/4” flat head screwdriver in
the tab. See Figure 1.
2. Gently pull upwards on the screwdriver handle until the
housing completely opens.
3. Observe polarity and place the battery in the holder and
press it into place.
3
The 1106 provides a Survey LED capability to allow one person to
confirm communication with the wireless receiver or panel while
the cover is removed.
1. Hold the 1106 in the exact desired location.
2. Press the tamper switch to send data to the panel and
determine if communication is confirmed or faulty.
Confirmed: If communication is confirmed, for each
press or release of the tamper switch the LED blinks
immediately on and immediately o.
Faulty: If communication is faulty, the LED remains on
for about 8 seconds or flashes multiple times in quick
succession. Relocate the 1106 or wireless receiver until
the LED confirms clear communication.
SELECT A LOCATION
Tab
DESCRIPTION
2 1106 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS
MOUNT THE 1106
For UL listed and commercial installations, use the supplied
screws when mounting the transmitter and the magnet.
Mount the Transmitter
1. If mounting with screws, remove the battery. If mounting
with double-sided tape, place the tape on the back of the
transmitter.
2. Hold the transmitter in place with the magnetic reed
switch closest to where the magnet will be mounted. See
Figure 2. Ensure the transmitter and the magnet will be no
more than 1/2” (1.3cm) apart.
3. If using screws, place the supplied #4 screws into the two
mounting holes and secure the transmitter to the surface.
If using double-sided tape, place the transmitter on the
surface.
4. Snap the transmitter cover back onto the base.
Mount the Magnet
Standard Installation
1. Push the supplied magnet into the magnet cover.
2. Hold the magnet base on the door closest to the
magnetic reed switch, no more than 1.3cm (0.5in) from the
transmitter.
3. If using screws, use the provided #4 screws to mount the
base. See Figure 3. If using double-sided tape, place the
tape on the back of the base and place on the surface.
4. Snap the cover onto the base.
Commercial Installation
1. Push the supplied magnet into the magnet cover.
2. Place and hold the magnet cover directly on the door
closest to the magnetic reed switch, no more than 1.3cm
(1.5in) apart from the transmitter.
3. Use the provided #4 screws to mount the cover.
See Figure 4.
4
5
TEST THE 1106
After installing the 1106, perform a Walk Test to confirm the 1106 is communicating with the panel.
At the keypad, enter 8144 (WALK) and select WLS. If the 1106 fails to check in at the keypad, relocate the
wireless device, receiver, or panel.
Figure 3: Standard Installation
Figure 4: Commercial Installation
Wall Mount
Screw Holes
Magnetic Reed
Switch
Figure 2: Transmitter Components
1106 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3
Connect External Contacts
Refer to Contacts and Zone Information in the appropriate panel programming guide for more information. DMP
recommends using 18 or 22 AWG un-shielded wire. If you use both the magnet reed switch in the 1106 transmitter
and an external contact, use consecutive zone numbers when connecting them to the panel.
1. Remove the cover of the 1106.
2. Use a flat head screwdriver to loosen the two screws on the 1106 terminal block. See Figure 5.
3. Insert the external contact wiring into the 1106 terminal block and tighten the screws.
4. Depending on how the contact was programmed in the Program the Panel section, connect the other ends of
the wires to the external contact as either normally open (N/O) or normally closed (N/C) without an end-of-
line resistor.
Figure 5: Connect External Contact
MODEL 1106
CR123
External Contact
Terminal Block
1106
Door
Window
External
Contact
ADDITIONAL INFORMATION
1. Open the transmitter housing to expose the inside of the 1106. See Figure 1.
2. Remove the old battery, observe polarity, and place the new battery in the holder.
3. Snap the cover back on the 1106.
Replace the Battery
Once the battery is replaced, a sensor reset is required at the keypad to clear the LOBAT message.
1. On an LCD Keypad, press and hold 2 for two seconds. On a Graphic Touchscreen Keypad,
press RESET.
2. Enter your user code, if required. The keypad displays SENSORS OFF followed by SENSORS
ON.
Sensor Reset to Clear LOBAT
Magnet
Program one
zone as an
internal contact.
Program the next
consecutive zone as
an internal contact.
EXTERNAL CONTACTS
Designed, engineered,
and manufactured in
Springfield, Missouri using U.S.
and global components.
LT-1377 1.01 18102
INTRUSION • FIRE • ACCESS • NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
866.266.2826 | DMP.com
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from
all persons. It must not be located or operated in conjunction with any other antenna or transmitter.
Changes or modifications made by the user and not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment o and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA INFORMATION
This device complies with Industry Canada Licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
1. This device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.
This system has been evaluated for RF Exposure per RSS-102 and is in compliance with the limits specified by Health
Canada Safety Code 6. The system must be installed at a minimum separation distance from the antenna to a general
bystander of 7.87 inches (20 cm) to maintain compliance with the General Population limits.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
1. l’appareil ne doit pas produire de brouillage, et
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
L’exposition aux radiofréquences de ce système a été évaluée selon la norme RSS-102 et est jugée conforme aux limites
établies par le Code de sécurité 6 de Santé Canada. Le système doit être installé à une distance minimale de 7.87 pouces
(20 cm) séparant l’antenne d’une personne présente en conformité avec les limites permises d’exposition du grand
public.
Patents
U. S. Patent No. 7,239,236
Certifications
FCC Part 15 Registration ID: CCKPC0124
Industry Canada: 5251A-PC0124
Underwriters Laboratory (UL) Listed
• ANSI/UL 1023 Household Burglar Alarm System
• ANSI/UL 634 Connections and Switches for use with Burglar Alarm
Systems Accessory
Universal Specifications
Do not use double-sided tape for listed installations.
Household Burglar Alarm System Units ANSI/UL 1023
Install only on non-conductive surfaces.
1106 Wireless Universal
Transmitter
Specifications
Battery
Life Expectancy 5 years (normal operation)
Type 3.0V lithium CR123A
Frequency Range 905-924 MHz
Color White
Housing Material Flame retardant ABS
Dimensions
Transmitter Case 1.79”L x 1.69”W x 0.84”H
Standard
Magnet Housing
1.35”L x 0.38”W x 0.43”H
Commercial Magnet Housing 2.25”L x 0.38”W x 0.34”H
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

DMP Electronics 1106 Guide d'installation

Marque
DMP Electronics
Modèle
1106
Catégorie
Lecteurs de contrôle d'accès
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents