Generac 16 kW 0058941 Manuel utilisateur

This manual must be used in conjunction with the Installation Manual before, and during installation!

Owner's Manual

8 - 20kW Air-cooled,

Automatic Standby Generators

L

I

S

T

E

D

C

U

S



NOT INTENDED FOR USE IN CRITICAL LIFE

SUPPORT APPLICATIONS.



ONLY QUALIFIED ELECTRICIANS OR CONTRACTORS

SHOULD ATTEMPT INSTALLATION!



DEADLY EXHAUST FUMES! OUTDOOR

INSTALLATION ONLY!

www.generac.com or 1-888-GENERAC

Introduction .............................................. 1

Read This Manual Thoroughly ................................................1

Safety Rules ............................................. 1

Contents ...............................................................................1

Operation and Maintenance....................................................1

How to Obtain Service ...........................................................1

Standards Index .....................................................................3

General Information ................................. 4

1.1 Unpacking/Inspection .....................................................4

1.2 Protection Systems ........................................................4

1.3 NEC Requirement for Arc Fault Circuit

Interruption Breaker for Bedrooms ..................................4

1.4 Emission Information......................................................5

1.5 The Generator ................................................................6

1.6 Specifications ................................................................7

1.7 Ready to Run .................................................................8

1.8 Fuel Requirements and Recommendations ......................8

1.9 Fuel Consumption ..........................................................8

1.10 Reconfiguring the Fuel System ........................................9

1.11 High Altitude Operation .................................................10

1.12 Location .......................................................................10

1.13 Battery Requirements ...................................................13

1.14 Battery Installation ........................................................13

1.15 The Battery ..................................................................13

1.16 Battery Charger ............................................................14

Post Installation Start-up and

Adjustments ........................................... 14

2.1 Activate the Generator ..................................................14

2.2 Before Initial Startup .....................................................14

2.3 Check Transfer Switch Operation ..................................14

2.4 Electrical Checks ..........................................................14

2.5 Generator Tests Under Load ..........................................16

2.6 Checking Automatic Operation ......................................16

Operation ................................................ 17

3.1 Control Panel Interface .................................................17

3.2 Automatic Transfer Operation ........................................18

3.3 Sequence of Automatic Operation .................................18

3.4 Manual Transfer Operation ............................................19

3.5 Side Compartment .......................................................20

3.6 Protection Systems ......................................................20

3.7 Shutting the Generator Down While Under Load ............22

Maintenance ........................................... 22

4.1 Performing Scheduled Maintenance ..............................22

4.2 Fuse .............................................................................22

4.3 Checking the Engine Oil Level .......................................23

4.4 Changing the Engine Oil ................................................23

4.5 Changing the Engine Air Cleaner ...................................24

4.6 Spark Plug(s) ...............................................................25

4.7 Battery Maintenance .....................................................26

4.8 Adjusting Valve Clearance .............................................26

4.9 Cooling System ............................................................27

4.10 Attention After Submersion ...........................................27

4.11 Corrosion Protection.....................................................27

4.12 Out of Service Procedure ..............................................27

4.13 Service Schedule .........................................................29

Troubleshooting ..................................... 30

5.1 Troubleshooting Guide ..................................................30

Appendix................................................. 31

6.1 Menu System Navigation ..............................................31

Installation Diagrams ............................ 33

Warranty ................................................. 38

MANUAL DEL USUARIO .................43

MANUEL DE L'UTILISATEUR ..........83

Table of Contents

1

INTRODUCTION

Thank you for purchasing this compact, high performance, air-cooled,

engine-driven generator. It is designed to automatically supply electrical

power to operate critical loads during a utility power failure.

This unit is factory installed in an all-weather, metal enclosure and is

intended exclusively for outdoor installation. This generator will operate

using either vapor withdrawn liquid propane (LP) or natural gas (NG).

NOTE:

This generator is suitable for supplying typical residential loads such

as Induction Motors (sump pumps, refrigerators, air conditioners,

furnaces, etc.), Electronic Components (computer, monitor, TV, etc.),

Lighting Loads and Microwaves.

READ THIS MANUAL THOROUGHLY

If any portion of this manual is not understood, contact the nearest Dealer

for starting, operating and servicing procedures. SAVE this Manual.

Provide this manual to any operator of the generator.

SAFETY RULES

Throughout this publication, and on tags and decals affixed to the genera-

tor, DANGER, WARNING, CAUTION and NOTE blocks are used to alert

personnel to special instructions about a particular operation that may be

hazardous if performed incorrectly or carelessly. Observe them carefully.

Their definitions are as follows:

INDICATES A HAZARDOUS SITUATION OR ACTION WHICH, IF

NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.

Indicates a hazardous situation or action which, if not

avoided, could result in death or serious injury.

Indicates a hazardous situation or action which, if not

avoided, could result in minor or moderate injury.

NOTE:

Notes contain additional information important to a procedure

and will be found within the regular text body of this manual.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the action or service are essential to

preventing accidents.

Four commonly used safety symbols accompany the DANGER,

WARNING and CAUTION blocks. The type of information each

indicates is as follows:



This symbol points out important safety information that,

if not followed, could endanger personal safety and/or

property of others.





This symbol points out potential explosion hazard.



This symbol points out potential fire hazard.



This symbol points out potential electrical shock hazard.

The operator is responsible for proper and safe use of the equipment. The

manufacturer strongly recommends that the operator read this Owner's

Manual and thoroughly understand all instructions before using this

equipment. The manufacturer also strongly recommends instructing other

users to properly start and operate the unit. This prepares them if they

need to operate the equipment in an emergency.

CONTENTS

This manual contains pertinent owner’s information for these models:

• 7 kW NG, 8 kW LP, single-cylinder GH-410 Engine

• 9 kW NG, 10 kW LP, V-twin GT-530 Engine

• 13 kW NG, 13 kW LP, V-twin GT-990 Engine

• 13 kW NG, 14 kW LP, V-twin GT-990 Engine

• 16 kW NG, 16 kW LP, V-twin GT-990 Engine

• 16 kW NG, 17 kW LP, V-twin GT-990 Engine

• 18 kW NG, 20 kW LP, V-twin GT-999 Engine

OPERATION AND MAINTENANCE

It is the operator's responsibility to perform all safety checks, to make sure

that all maintenance for safe operation is performed promptly, and to have

the equipment checked periodically by a Dealer. Normal maintenance ser-

vice and replacement of parts are the responsibility of the owner/operator

and, as such, are not considered defects in materials or workmanship

within the terms of the warranty. Individual operating habits and usage

contribute to the need for maintenance service.

Proper maintenance and care of the generator ensures a minimum number

of problems and keep operating expenses at a minimum. See a Dealer for

service aids and accessories.

HOW TO OBTAIN SERVICE

When the generator requires servicing or repairs, contact a Dealer for

assistance. Service technicians are factory-trained and are capable of

handling all service needs.

When contacting a Dealer about parts and service, always supply the

complete model number and serial number of the unit as given on its data

decal, which is located on the generator. See section "The Generator" for

decal location.

Model No. _________________ Serial No. ______________

Safety Rules

2

Study these SAFETY RULES carefully before installing, operating

or servicing this equipment. Become familiar with this Owner’s

Manual and with the unit. The generator can operate safely, effi-

ciently and reliably only if it is properly installed, operated and

maintained. Many accidents are caused by failing to follow simple

and fundamental rules or precautions.

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all-inclusive. If

using a procedure, work method or operating technique the manu-

facturer does not specifically recommend, ensure that it is safe for

others. Also make sure the procedure, work method or operating

technique utilized does not render the generator unsafe.



Despite the safe design of this generator,

operating this equipment imprudently, neglect-

ing its maintenance or being careless can

cause possible injury or death. Permit only

responsible and capable persons to install,

operate and maintain this equipment.



Potentially lethal voltages are generated by

these machines. Ensure all steps are taken to

render the machine safe before attempting to

work on the generator.



Parts of the generator are rotating and/or

hot during operation. Exercise care near run-

ning generators.



Installation must always comply with appli-

cable codes, standards, laws and regula-

tions.



A running generator gives off carbon mon-

oxide, and odorless, colorless poison gas.

Breathing in carbon monoxide can cause

headaches, fatigue, diziness, nausea, vomit-

ting, confusion, fainting, siezures or death.

GENERAL HAZARDS

• For safety reasons, the manufacturer recommends that this equip-

ment be installed, serviced and repaired by a Service Dealer or

other competent, qualified electrician or installation technician who

is familiar with applicable codes, standards and regulations. The

operator also must comply with all such codes, standards and

regulations.

• The engine exhaust fumes contain carbon monoxide, which

can be DEADLY. This dangerous gas, if breathed in sufficient

concentrations, can cause unconsciousness or even death.

Do NOT alter or add to the exhaust system or do anything that

might render the system unsafe or in noncompliance with appli-

cable codes and standards.

• Install a battery operated carbon monoxide alarm indoors,

according to manufacturer's instructions/recommendations.

• Adequate, unobstructed flow of cooling and ventilating air is

critical to correct generator operation. Do not alter the instal-

lation or permit even partial blockage of ventilation provisions,

as this can seriously affect safe operation of the generator. The

generator MUST be installed and operated outdoors only.

• Keep hands, feet, clothing, etc., away from drive belts, fans,

and other moving or hot parts. Never remove any drive belt or

fan guard while the unit is operating.

• When working on this equipment, remain alert at all times.

Never work on the equipment when physically or mentally

fatigued.

• Inspect the generator regularly, and contact the nearest Dealer

for parts needing repair or replacement.

• Before performing any maintenance on the generator, discon-

nect its battery cables to prevent accidental start up. Disconnect

the cable from the battery post indicated by a NEGATIVE, NEG

or (–) first, then remove the POSITIVE, POS or (+) cable. When

reconnecting the cables, connect the POSITIVE cable first, the

NEGATIVE cable last.

• Never use the generator or any of its parts as a step. Stepping

on the unit can stress and break parts, and may result in dan-

gerous operating conditions from leaking exhaust gases, fuel

leakage, oil leakage, etc.

EXHAUST HAZARDS

• Generator engine exhaust contains DEADLY carbon monox-

ide, an odorless, colorless poisonous gas. Breathing carbon

monoxide can cause: dizziness, throbbing temples, nausea,

muscular twitching, headache, vomiting, weakness and sleepi-

ness, inability to think clearly, fainting, unconsciousness or

even death. If you experience any carbon monoxide poisoning

symptoms, move into fresh air and immediately seek medical

attention.

• NEVER operate the generator set inside any garage or other

enclosed area EVEN IF the doors and windows are open.

ELECTRICAL HAZARDS

• All generators covered by this manual produce dangerous elec-

trical voltages and can cause fatal electrical shock. Utility power

delivers extremely high and dangerous voltages to the transfer

switch as does the standby generator when it is in operation.

Avoid contact with bare wires, terminals, connections, etc.,

while the unit is running. Ensure all appropriate covers, guards

and barriers are in place, secured and/or locked before operat-

ing the generator. If work must be done around an operating

unit, stand on an insulated, dry surface to reduce shock hazard.

• DO NOT handle any kind of electrical device while stand-

ing in water, while barefoot, or while hands or feet are wet.

DANGEROUS ELECTRICAL SHOCK MAY RESULT.



SAVE THESE INSTRUCTIONS – The manufacturer suggests that these rules for safe operation be copied and posted near the unit’s

installation site. Safety should be stressed to all operators and potential operators of this equipment.

Safety Rules

3

• The National Electrical Code (NEC) requires the frame and external

electrically conductive parts of the generator to be connected to

an approved earth ground. Local electrical codes also may require

proper grounding of the generator electrical system.

• After installing this home standby electrical system, the genera-

tor may crank and start at any time without warning. When this

occurs, load circuits are transferred to the STANDBY (genera-

tor) power source. To prevent possible injury if such a start and

transfer occur, always set the generator’s AUTO/OFF/MANUAL

switch to its OFF position before working on equipment and

remove the 7.5A fuse from the generator control panel.

• In case of accident caused by electric shock, immediately shut

down the source of electrical power. If this is not possible,

attempt to free the victim from the live conductor. AVOID DIRECT

CONTACT WITH THE VICTIM. Use a nonconducting implement,

such as a dry rope or board, to free the victim from the live

conductor. If the victim is unconscious, apply first aid and get

immediate medical help.

• Never wear jewelry when working on this equipment. Jewelry

can conduct electricity resulting in electric shock, or may get

caught in moving components causing injury.

FIRE HAZARDS

• For fire safety, the generator must be installed and maintained

properly. Installation must always comply with applicable

codes, standards, laws and regulations. Adhere strictly

to local, state and national electrical and building codes.

Comply with regulations the Occupational Safety and Health

Administration (OSHA) has established. Also, ensure that the

generator is installed in accordance with the manufacturer’s

instructions and recommendations. Following proper installa-

tion, do nothing that might alter a safe installation and render

the unit in noncompliance with the aforementioned codes,

standards, laws and regulations.

• Keep a fire extinguisher near the generator at all times.

Extinguishers rated “ABC” by the National Fire Protection

Association are appropriate for use on the standby electric

system. Keep the extinguisher properly charged and be familiar

with its use. Consult the local fire department with any ques-

tions pertaining to fire extinguishers.

EXPLOSION HAZARDS

• Do not smoke around the generator. Wipe up any fuel or oil

spills immediately. Ensure that no combustible materials are left

in the generator compartment, or on or near the generator, as

FIRE or EXPLOSION may result. Keep the area surrounding the

generator clean and free from debris.

• Gaseous fluids such as natural gas and liquid propane (LP)

gas are extremely EXPLOSIVE. Install the fuel supply system

according to applicable fuel-gas codes. Before placing the

home standby electric system into service, fuel system lines

must be properly purged and leak tested according to applica-

ble code. After installation, inspect the fuel system periodically

for leaks. No leakage is permitted.

STANDARDS INDEX

Applicable national, state, or local laws, codes, and regulations

pertaining to the installation of engine-generator power systems

must be strictly complied with. Always use the current accept-

able version or edition of the applicable code or standard which

applies to your jurisdiction. In the absence of pertinent local laws

and standards, the following published booklets may be used as

a guide (these apply to localities which recognize NFPA and IBC):

1. National Fire Protection Association (NFPA) 70: The NATIONAL

ELECTRIC CODE (NEC) *

2. NFPA 10: Standard for Portable Fire Extinguishers *

3. NFPA 30: Flammable And Combustible Liquids Code *

4. NFPA 37: Standard for Stationary Combustion Engines And

Gas Turbines *

5. NFPA 54: National Fuel Gas Code *

6. NFPA 58: Standard for Storage And Handling Of Liquefied

Petroleum Gases *

7. NFPA 70E: Standard For Electrical Safety In The Workplace *

8. NFPA 5000: Building Code *

9. ASAE EP-364.2 Installation and Maintenance of Farm Standby

Electric Power ****

10. Agricultural Wiring Handbook ***

11. International Building Code **

This list is not all inclusive. Check with the Authority Having Local

Jurisdiction (AHJ) for any local codes or standards which may

be applicable to your jurisdiction. The above listed standards are

available from the following internet sources:

* www.nfpa.org

** www.iccsafe.org

*** www.rerc.org Rural Electricity Resource Council, P.O. Box

309 Wilmington, OH 45177-0309

**** www.asabe.org American Society of Agricultural & Biological

Engineers, 2950 Niles Road, St. Joseph, MI 49085

CALIFORNIA PROPOSITION 65 WARNING

Engine exhaust and some of its constituents are known

to the State of California to cause cancer, birth defects

and other reproductive harm.

CALIFORNIA PROPOSITION 65 WARNING

This product contains or emits chemicals known to the

State of California to cause cancer, birth defects and

other reproductive harm.

Safety Rules



Only qualified electricians or contractors

should attempt such installations, which must

comply strictly with applicable codes, stan-

dards and regulations.

1.1 UNPACKING/INSPECTION

After unpacking, carefully inspect the contents for damage.

• This standby generator set is ready for installation with a factory

supplied and pre-mounted base pad and has a weather protec-

tive enclosure that is intended for outdoor installation only.

• This UL listed standby generator set may be packaged with an

automatic transfer switch with built in load center. The combi-

nation transfer switch and load center is pre-wired with a two

foot and 30 foot conduit. Circuit breakers for emergency circuit

connections are included (if equipped).

• This UL listed, 2-pole switch is rated at 100 or 200 AC amperes

at 250 volts maximum. The 100 Amp transfer switch is for

indoor use only. The 200 Amp transfer switch is for indoor/

outdoor use (if equipped).



If this generator is used to power electrical load

circuits normally powered by a utility power

source, it is required by code to install a trans-

fer switch. The transfer switch must effectively

isolate the electrical system from the utility

distribution system when the generator is oper-

ating (NEC 700, 701 & 702). Failure to isolate an

electrical system by such means will result in

damage to the generator and also may result in

injury or death to utility power workers due to

backfeed of electrical energy.

If any loss or damage is noted at time of delivery, have the

person(s) making the delivery note all damage on the freight bill

or affix their signature under the consignor's memo of loss or

damage.

If a loss or damage is noted after delivery, separate the damaged

materials and contact the carrier for claim procedures.

“Concealed damage” is understood to mean damage to the con-

tents of a package that is not in evidence at the time of delivery,

but is discovered later.

To properly open the roof, press down on the center top lip and

release the latch. If pressure is not applied from the top, the roof

may appear stuck. Always verify that the side lock is unlocked

before attempting to lift the roof.

1.2 PROTECTION SYSTEMS

Unlike an automobile engine, the generator may have to run for

long periods of time with no operator present to monitor engine

conditions. For that reason, the engine is equipped with the fol-

lowing systems that protect it against potentially damaging condi-

tions:

1. Low Oil Pressure Sensor 6. Low Battery

2. High Temperature Sensor 7. Under-frequency

3. Overcrank 8. Undervoltage

4. Overspeed 9. Overvoltage

5. RPM Sensor 10. Internal Failure

There are readouts on the control panel to notify personnel that

one of these failures has occurred. There is a Status message on

the display that displays when all of the conditions described in the

"Ready to Run" section are true.

1.3 NEC REQUIREMENT

FOR ARC FAULT CIRCUIT

INTERRUPTION BREAKER

FOR BEDROOMS

In 2001, the National Electric Code (NEC) introduced a requirement

for new construction. This new requirement indicates the need for

Arc Fault Circuit Interrupters to be used to protect the complete

branch circuit that feeds a dwelling bedroom. The actual NEC

requirement is indicated below.

1.3.1 SECTION 210.12 ARC FAULT CIRCUIT

INTERRUPTER PROTECTION

1. Definition: An arc fault circuit interrupter is a device intended

to provide protection from the effects of arc faults by recog-

nizing characteristics unique to arcing and by functioning to

de-energize the circuit when an arc fault is detected.

2. Dwelling Unit Bedrooms: All branch circuits that supply 125

volt, single-phase, 15 and 20 ampere outlets installed in

dwelling unit bedrooms shall be protected by an arc fault cir-

cuit interrupter listed to provide protection of the entire branch

circuit.

Section 210.12 requires that AFCI protection be provided on branch

circuits that supply outlets (receptacle, lighting, etc.) in dwell-

ing bedrooms. The requirement is limited to 15 and 20 ampere,

125 volt circuits. There is no prohibition against providing AFCI

protection on other circuits or in locations other than bedrooms.

Because circuits are often shared between a bedroom and other

areas such as closets and hallways, providing AFCI protection on

the complete circuit would comply with 210.12.

4

General Information

5

If during the installation of the home standby system the decision

is made to provide back up power to a bedroom branch circuit,

then the circuit breaker in the transfer switch should be replaced

with an Arc Fault Circuit Interrupter.

It is most important that breakers only be switched like for like.

For instance, if replacing a 15A breaker, it MUST be replaced with

a 15A AFCI breaker. Likewise, a 20A breaker MUST be replaced

with a 20A AFCI.

These AFCI breakers are available at the nearest hardware store.

Item # Description

Q115AF 15A Single Pole AFCI

Q120AF 20A Single Pole AFCI

1.4 EMISSION INFORMATION

The U.S. Environmental Protection Agency (EPA) requires that

this generator comply with exhaust emission standards. This

generator is certified to meet the applicable EPA emission levels,

and is certified for use as a stationary engine for standby power

generation. Any other use may be a violation of federal and/or local

laws. It is important to follow the maintenance specifications in the

Maintenance section to ensure that the engine complies with the

applicable emission standards for the duration of the engine’s life.

This generator is certified to operate on Liquid Propane Vapor fuel

and pipeline Natural Gas.

For generators 10kW and below, the Emission Control System

consists of the following components:

• Air Induction System

– Intake Pipe / Manifold

– Air Cleaner

• Fuel Metering System

– Carburetor / Mixer Assembly

– Fuel Regulator

• Ignition System

– Spark Plug

– Ignition Module

• Exhaust System

– Exhaust Manifold

– Muffler / Catalyst

For generators 13kW and greater, the Emission Control System

code is EM (Engine Modification) and consists of the following

components:

• Air Induction System

– Intake Pipe / Manifold

– Air Cleaner

• Fuel Metering System

– Carburetor / Mixer Assembly

– Fuel Regulator

• Ignition System

– Spark Plug

– Ignition Module

• Exhaust System

– Exhaust Manifold

– Muffler

General Information

6

1.5 THE GENERATOR

Data Label

(see sample)

Oil

Dipstick

Exhaust

Enclosure

Composite Base Oil Filter Battery Compartment

Fuel

Regulator

Fuel Inlet

(back)

Air Filter

Circuit

Breaker

Control

Panel

Data Label

(see sample)

Oil

Dipstick

Exhaust

Enclosure

Composite Base Oil Filter Battery Compartment

Fuel

Regulator

Fuel Inlet

(back)

Air Filter

Circuit

Breakers

Control

Panel

Figure 1.3 – 13, 14, 16, 17 and 20kW, V-twin,

GT-990/GT-999 Engine (door removed)

Figure 1.1 – 8kW, Single Cylinder, GH-410 Engine (door

removed)

Data Label

(see sample)

Oil

Dipstick

Exhaust

Enclosure

Composite Base Oil Filter Battery Compartment

Fuel

Regulator

Fuel Inlet

(back)

Air

Filter

Circuit

Breaker

Control

Panel

Figure 1.2 – 10kW, V-twin, GT-530 Engine

(door removed)

Data Label Sample

General Information

7

1.6 SPECIFICATIONS

1.6.1 GENERATOR

Model 8kW 10kW 13kW 14kW 16kW 17kW 20kW

Rated Voltage 240

Rated Maximum Load Current

(Amps) at 240 Volts (LP)*

33.3 41.6 54.1 58.3 66.6 70.8 83.3

Main Circuit Breaker 35 Amp 45 Amp 55 Amp 60 Amp 65 Amp 65 Amp 90 Amp

Circuits** 50A, 240V - - 1 - 1 1 -

40A, 240V - 1 1 1 1 1 -

30A, 240V 1 1 - - - - -

20A, 240V 1 - 1 1 1 1 -

20A, 120V 3 3 4 6 5 5 -

15A, 120V 3 5 4 4 5 5 -

Phase 1

Number of Rotor Poles 2

Rated AC Frequency 60 Hz

Battery Requirement Group 26R, 12 Volts and 525 CCA Minimum

Weight (unit only in lbs.) 340 387 439 439 439421 455/421 450

Enclosure Steel Steel Steel Steel Steel/Aluminum Steel/Aluminum Aluminum

Normal Operating Range

This unit is tested in accordance to UL 2200 standards with an operating temperature of -20 °F (-29 °C) to 122 °F. (50 °C). For areas where temperatures fall

below 32 °F (0 °C), a cold weather kit is highly recommended. When operated above 77º F (25º C) there may be a decrease in engine power. (Please reference the

engine specifications section).

These generators are rated in accordance with UL2200, Safety Standard for Stationary Engine Generator Assemblies; and CSA-C22.2 No. 100-04 Standard for Motors and Generators.

* Natural Gas ratings will depend on specific fuel Btu content. Typical derates are between 10-20% off the LP gas rating.

** Circuits to be moved must be protected by same size breaker. For example, a 15 amp circuit in the main panel must be a 15 amp circuit in the transfer switch.

1.6.2 ENGINE

Model 8 kW 10 kW 13/14/16/17 kW 20 kW

Type of Engine GH-410 GT-530 GT-990 GT-999

Number of Cylinders 1 2 2 2

Rated Horsepower @ 3,600 rpm* 14.8 18 32 36

Displacement 410cc 530cc 992cc 999cc

Cylinder Block Aluminum w/Cast Iron Sleeve

Valve Arrangement Overhead Valves

Ignition System Solid-state w/Magneto

Recommended Spark Plug RC14YC BPR6HS RC14YC RC12YC

Spark Plug Gap 0.76 mm (0.030 inch) 0.76 mm (0.030 inch) 1.02 mm (0.040 inch) 0.76 mm (0.030 inch)

Compression Ratio 8.6:1 9.5:1 9.5:1 9.5:1

Starter 12 VDC

Oil Capacity Including Filter Approx. 1.5 Qts Approx. 1.7 Qts Approx. 1.9 Qts Approx. 1.9 Qts

Recommended Oil Filter Part # 070185F

Recommended Air Filter Part # 0G3332 Part # 0E9581 Part # 0C8127 Part # 0G5894

Operating RPM 3,600

* Engine power is subject to and limited by such factors as fuel Btu content, ambient temperature and altitude. Engine power decreases about 3.5 percent for each 1,000 feet above sea level; and

also will decrease about 1 percent for each 6 C (10 F) above 16 C (60 F) ambient temperature.

General Information

1.7 READY TO RUN

The "Ready to Run" on the display is ready when all of the following

conditions are true:

1. The AUTO/OFF/MANUAL switch is set to the AUTO position.

2. The utility voltage being supplied to the unit is being sensed

by the PCB. If the utility sense voltage is not connected to the

unit or if it is below approximately 150-160 volts AC, then

the system will display the message "No Utility Present". This

indicates that if the AUTO/OFF/MANUAL switch is placed in

the Auto position, the generator will start.

3. No alarms are present, for example, low oil pressure, high

temperature, etc.

1.8 FUEL REQUIREMENTS AND

RECOMMENDATIONS

With LP gas, use only the vapor withdrawal system. This type of

system uses the vapors formed above the liquid fuel in the storage

tank.

The engine has been fitted with a fuel carburetion system that

meets the specifications of the 1997 California Air Resources

Board for tamper-proof dual fuel systems. The unit will run on

natural gas or LP gas, but it has been factory set to run on natural

gas. Should the primary fuel need to be changed to LP gas, the

fuel system needs to be reconfigured. See the reconfiguring the

Fuel System section for instructions on reconfiguration of the fuel

system.

Recommended fuels should have a Btu content of at least 1,000

Btus per cubic foot for natural gas; or at least 2,520 Btus per

cubic foot for LP gas. Ask the fuel supplier for the Btu content of

the fuel.

Required fuel pressure for natural gas is five (5) inches to seven

(7) inches water column (0.18 to 0.25 psi); and for liquid pro-

pane, 10 inches to 12 inches of water column (0.36 to 0.43 psi).

The primary regulator for the propane supply is NOT INCLUDED

with the generator.

NOTE:

All pipe sizing, construction and layout must comply with NFPA

54 for natural gas applications and NFPA 58 for liquid propane

applications. Once the generator is installed, verify that the fuel

pressure NEVER drops more than one (1) inch water column

from no load to full load from the starting pressure for either

fuel type, and remains within the limits of the stated specifica-

tion.

Prior to installation of the generator, the installer should consult

local fuel suppliers or the fire marshal to check codes and regula-

tions for proper installation. Local codes will mandate correct rout-

ing of gaseous fuel line piping around gardens, shrubs and other

landscaping to prevent any damage.

Special considerations should be given when installing the unit

where local conditions include flooding, tornados, hurricanes,

earthquakes and unstable ground for the flexibility and strength of

piping and their connections.

Use an approved pipe sealant or joint compound on all threaded

fittings.

All installed gaseous fuel piping must be purged and leak tested

prior to initial start-up in accordance with local codes, standards

and regulations.

1.9 FUEL CONSUMPTION

Unit

Nat. Gas LP Vapor

1/2 Load Full Load 1/2 Load Full Load

7/8 kW 77 140 0.94/34 1.68/62

9/10 kW 102 156 1.25/46 1.93/70

13/13 kW 156 220 1.55/57 2.18/80

13/14 kW 156 220 1.56/58 2.30/84

16/16 kW 183 261 1.59/58 2.51/91

16/17 kW 183 261 1.61/59 2.57/94

18/20 kW 206 294 1.89/69 2.90/106

* Natural gas is in cubic feet per hour.

** LP is in gallons per hour/cubic feet per hour.

*** Values given are approximate.

Verify that gas meter and all piping is capable of providing enough

fuel flow at full load to include household appliances.

1.9.1 BTU FLOW REQUIREMENTS - NATURAL GAS

BTU flow required for each unit based on 1000 BTU per cubic foot.

• 7kW — 140,000 BTU/Hour

• 9kW — 156,000 BTU/Hour

• 13kW — 220,000 BTU/Hour

• 16kW — 261,000 BTU/Hour

• 18kW — 294,000 BTU/Hour





Gaseous fuels such as natural gas and liquid

propane (LP) gas are highly explosive. Even

the slightest spark can ignite such fuels and

cause an explosion. No leakage of fuel is

permitted. Natural gas, which is lighter than

air, tends to collect in high areas. LP gas is

heavier than air and tends to settle in low

areas.

NOTE:

A minimum of one approved manual shut-off valve must be

installed in the gaseous fuel supply line. The valve must be eas-

ily accessible. Local codes determine the proper location.

8

General Information

9

1.10 RECONFIGURING THE FUEL

SYSTEM

1.10.1 8 KW, 410CC ENGINE

To reconfigure the fuel system from NG to LP, follow these steps

(Figure 1.4):

NOTE:

The primary regulator for the propane supply is NOT INCLUDED

with the generator. A fuel pressure of 10 to 12 inches of water

column (0.36 to 0.43 psi) to the fuel inlet of the generator MUST

BE SUPPLIED.

1. Turn off the main gas supply (if connected).

2. Open the roof and remove the door.

3. Remove the battery (if installed).

4. Take the plastic T-handle fuel selector in the poly bag supplied

with the generator.

5. Locate the selector knob on the air box cover, behind the

yellow air filter door and power bulge. The unit comes from

the factory in the NG (Natural Gas) position. Grasping the

T-handle, insert the pin end into the hole in the selector knob

and pull out to overcome spring pressure and then twist

clockwise 90 degrees and allow the selector to return in once

aligned with the LP (Liquid Propane) position.

6. Save this tool with the Owner's Manual.

7. Install the battery, door and close the roof.

8. Reverse the procedure to convert back to natural gas.

Figure 1.4 – Fuel Selector

NOTE:

Use an approved pipe sealant or joint compound on all threaded

fittings to reduce the possibility of leakage.

1.10.2 10, 13, 14, 16, 17 AND 20KW, V-TWIN ENGINES

To reconfigure the fuel system from NG to LP, follow these steps:

NOTE:

The primary regulator for the propane supply is NOT INCLUDED

with the generator. A fuel pressure of 10 to 12 inches of water

column (0.36 to 0.43 psi) to the fuel inlet of the generator MUST

BE SUPPLIED AND MAINTAINED UP TO FULL LOAD.

1. Open the roof.

2. For 10kW units: Loosen clamp and slide back the air inlet

hose.

– Slide fuel selector on carburetor out towards the back of the

enclosure (Figures 1.5 and 1.6).

– Return the inlet hose and tighten clamp securely.

For 13, 14, 16, 17 and 20kW units: remove the air cleaner

cover.

– Slide the selector lever out towards the back of the enclosure

(Figures 1.7 and 1.8).

– Return the air cleaner cover and tighten the two thumb

screws.

Figure 1.5 - 10kW, GT-530 (Inlet Hose Slid Back)

Fuel Selection

Lever - "In"

Position for

Natural Gas

Fuel

Figure 1.6 - 10kW, GT-530 (Inlet Hose Slid Back)

Fuel Selection

Lever - "Out"

Position for

Liquid Propane

(Vapor) Fuel

General Information

10

3. Close the roof.

4. Reverse the procedure to convert back to natural gas.

Figure 1.7 - 13, 14, 16, 17, & 20kW,

GT-990/GT-999 (Airbox Cover Removed)

Fuel Selection Lever - "In" Position for Natural Gas Fuel

Figure 1.8 - 13, 14, 16, 17, & 20kW,

GT-990/GT-999 (Airbox Cover Removed)

Fuel Selection Lever - "Out" Position for Liquid Propane

(Vapor) Fuel

1.11 HIGH ALTITUDE OPERATION

The fuel system on this generator may be influenced by operation

at higher altitudes. Proper operation can be ensured by installing

an altitude kit when required. See the table below to determine

when an altitude kit is required. Operating this generator without

the proper altitude kit installed may increase the engine’s emis-

sions and decrease fuel economy and performance. Kits may be

obtained from any Dealer, and should be installed by a qualified

individual.

1.12 LOCATION



The engine exhaust fumes contain carbon

monoxide, which can be DEADLY. This dan-

gerous gas, if breathed in sufficient con-

centrations, can cause unconsciousness or

even death. This generator must be installed

properly, in strict compliance with applicable

codes and standards. Following installation,

do nothing that might render the system

unsafe or in noncompliance with such codes

and standards.

Operate the generator outdoors ONLY.

• Keep exhaust gases from entering a confined

area through windows, doors, ventilation, crawl

spaces or other openings (Figure 1.9).

• It is highly recommended that carbon monox-

ide detector(s) be installed indoors according

to the manufacturer's instructions/recommen-

dations.

• The generator must be mounted safely per

applicable codes and the manufacturer's speci-

fications. Do NOT alter or add to the exhaust

system, or do anything that might render the

exhaust system unsafe or in noncompliance

with applicable codes and standards.

1.12.1 GENERATOR

Install the generator set, in its protective enclosure, outdoors,

where adequate cooling and ventilating air is always available

(Figure 1.9). Consider these factors:

• The installation of the generator must comply strictly with

NFPA 37, NFPA 54, NFPA 58, and NFPA 70 standards.

• Install the unit where air inlet and outlet openings will not

become obstructed by leaves, grass, snow, etc.. If prevailing

winds will cause blowing or drifting, consider using a wind-

break to protect the unit.

• Install the generator on high ground where water levels will not

rise and endanger it.

General Information

11

• Allow sufficient room on all sides of the generator for mainte-

nance and servicing. This unit must be installed in accordance

with current applicable NFPA 37 and NFPA 70 standards; as

well as any other federal, state and local codes for minimum

distances from other structures. DO NOT install under wooden

decks or structures unless there is at least five (5) feet of clear-

ance above the generator, three (3) feet of clearance on sides

and front, and 18 inches of clearance at back of unit.

• Install the unit where rain gutter down spouts, roof run-off,

landscape irrigation, water sprinklers or sump pump discharge

does not flood the unit or spray the enclosure, including any air

inlet or outlet openings.

• Install the unit where services will not be affected or obstructed,

including concealed, underground or covered services such as

electrical, fuel, phone, air conditioning or irrigation.

• Where strong prevailing winds blow from one direction, face the

generator air inlet openings to the prevailing winds.

• Install the generator as close as possible to the fuel supply, to

reduce the length of piping.

• Install the generator as close as possible to the transfer switch.

REMEMBER THAT LAWS OR CODES MAY REGULATE THE

DISTANCE AND LOCATION.

• The genset must be installed on a level surface. The base frame

must be level within two (2) inches all around.

• The generator is typically placed on pea gravel or crushed

stone. Check local codes if a concrete slab is required. If a

concrete base slab is required, all federal, state and local codes

should be followed. Special attention should be given to the

concrete base slab which should exceed the length and width

of the generator by a minimum of six (6) inches (0.152 meters)

on all sides.

Figure 1.9 – Generator Clearances

1.12.2 INSTALLATION GUIDELINES FOR STATIONARY

STATIONARY AIR-COOLED 8 - 20KW

GENERATORS

The National Fire Protection Association has a standard for the

installation and use of stationary combustion engines. That

standard is NFPA 37 and its requirements limit the spacing of an

enclosed generator set from a structure or wall (Figure 1.10).

NFPA 37, Section 4.1.4, Engines Located Outdoors. Engines, and

their weatherproof housings if provided, that are installed outdoors

shall be located at least 5 ft. from openings in walls and at least 5

ft. from structures having combustible walls. A minimum separa-

tion shall not be required where the following conditions exist:

1. The adjacent wall of the structure has a fire resistance rating

of at least 1 hour.

2. The weatherproof enclosure is constructed of noncombus-

tible materials and it has been demonstrated that a fire within

the enclosure will not ignite combustible materials outside the

enclosure.

Annex A — Explanatory Material

A4.1.4 (2) Means of demonstrating compliance are by means

of full scale fire test or by calculation procedures.

Because of the limited spaces that are frequently available for

installation, it has become apparent that exception (2) would be

beneficial for many residential and commercial installations. With

that in mind, the manufacturer contracted with an independent

testing laboratory to run full scale fire tests to assure that the

enclosure will not ignite combustible materials outside the enclo-

sure.

The criteria was to determine the worst case fire scenario within

the generator and to determine the ignitability of items outside the

engine enclosure at various distances. The enclosure is construct-

ed of non-combustible materials and the results and conclusions

from the independent testing lab indicated that any fire within the

generator enclosure would not pose any ignition risk to nearby

combustibles or structures, with or without fire service personnel

response.

Based on this testing and the requirements of NFPA 37, Sec 4.1.4,

the guidelines for installation of the generators listed above are

changed to 18 inches (457mm) from the back side of the genera-

tor to a stationary wall or building. For adequate maintenance and

airflow clearance, the area above the generator should be at least

4 feet with a minimum of 3 feet at the front and ends of the enclo-

sure. This would include trees, shrubs and vegetation that could

obstruct airflow. See the diagram on the reverse of this page and

the installation drawing within the owner’s manual for details.

Generator exhaust contains DEADLY carbon monoxide gas. This

dangerous gas can cause unconsciousness or death. Do not place

the unit near windows, doors, fresh air intakes (furnaces, etc.) or

any openings in the building or structure, including windows and

doors of an attached garage.

General Information

12

Figure 1.10 – Installation Guidelines

18 inches

Minimum Distance

36 inches

60 inches 60 inches

Existing Wall

No operable windows or openings in the wall permitted

within 5 feet from any point of the generator.

Top of Generator

60” Minimum

60” Recommended

Minimum From Ends

18 inches

Minimum

Generator

Clearance from operable

windows, doors, any

openings in the wall,

shrubs or vegetation over

12” in height

Clearance from the ends and front of the

generator should be 36 inches. This

would include shrubs, trees and any

kind of vegetation. Clearance at the top

should be a minimum of 60 inches from

any structure, overhang or projections

from the wall. The generator should not

be placed under a deck or other

structure that is closed in and would limit

or contain air flow.

These guidelines are based upon fire

testing of the generator enclosure and

the manufacturer’s requirement for air

flow for proper operation. Local codes

may be different and more restrictive

than what is described here.

This drawing supersedes installation instructions in all air-cooled installation and owner’s manuals dated previous

to May 26, 2007.

General Information

13





If the AUTO/OFF/MANUAL switch is not set

to its OFF position, the generator can crank

and start as soon as the battery cables are

connected. If the utility power supply is not

turned off, sparking can occur at the battery

posts and cause an explosion.

1.13 BATTERY REQUIREMENTS

See the Specifications section for correct battery size and rating.

1.14 BATTERY INSTALLATION

Fill the battery with the proper electrolyte fluid if necessary and

have the battery fully charged before installing it.

Before installing and connecting the battery, complete the follow-

ing steps:

1. Set the generator's AUTO/OFF/MANUAL switch to OFF.

2. Turn off utility power supply to the transfer switch.

3. Remove the 7.5A fuse from the generator control panel.

Battery cables were factory connected at the generator (Figure

1.11). Connect cables to battery posts as follows:

4. Connect the red battery cable (from starter contactor) to the

battery post indicated by a positive, POS or (+).

5. Connect the black battery cable (from frame ground) to the

battery post indicated by a negative, NEG or (—).

6. Install the battery post covers (included).

NOTE:

Dielectric grease should be used on battery posts to aid in the

prevention of corrosion.

NOTE:

Damage will result if battery connections are made in reverse.

Figure 1.11 – Battery Cable Connections

NOTE:

In areas where temperatures regularly fall below 32° F (0° C) it

is recommended that a pad type battery heater be installed to

aid in cold climate starting.

1.15 THE BATTERY





DO NOT dispose of the battery in a fire. The

battery is capable of exploding.



A battery presents a risk of electrical shock

and high short circuit current. The following

precautions are to be observed when work-

ing on batteries:

• Remove the 7.5A fuse from the generator con-

trol panel.

• Remove watches, rings or other metal objects.

• Use tools with insulated handles.

• Wear rubber gloves and boots.

• Do not lay tools or metal parts on top of the

battery.

• Disconnect charging source prior to connecting

or disconnecting battery terminals.



Do not open or mutilate the battery.

Released electrolyte has been known to

be harmful to the skin and eyes, and to be

toxic.



The electrolyte is a dilute sulfuric acid that

is harmful to the skin and eyes. It is electri-

cally conductive and corrosive.

The following procedures are to be observed:

• Wear full eye protection and protective clothing.

• Where electrolyte contacts the skin, wash it off

immediately with water.

• Where electrolyte contacts the eyes, flush thor-

oughly and immediately with water and seek

medical attention.

• Spilled electrolyte is to be washed down with

an acid neutralizing agent. A common practice

is to use a solution of 1 pound (500 grams)

bicarbonate of soda to 1 gallon (4 liters) of

water. The bicarbonate of soda solution is to

be added until the evidence of reaction (foam-

ing) has ceased. The resulting liquid is to be

flushed with water and the area dried.



Lead-acid batteries present a risk of fire

because they generate hydrogen gas. The fol-

lowing procedures are to be followed:

• DO NOT SMOKE when near the battery.

• DO NOT cause flame or spark in battery area.

• Discharge static electricity from body before

touching the battery by first touching a ground-

ed metal surface.



Be sure the AUTO/OFF/MANUAL switch is

set to the OFF position before connecting

the battery cables. If the switch is set to

AUTO or MANUAL, the generator can crank

and start as soon as the battery cables are

connected.

General Information

14





Be sure the utility power supply is turned off

and the 7.5A fuse is removed from the gener-

ator control panel, or sparking may occur at

the battery posts as the cables are attached

and cause an explosion.

Servicing of the battery is to be performed or supervised by per-

sonnel knowledgeable of batteries and the required precautions.

Keep unauthorized personnel away from batteries.

See the Specifications section for the correct size and rating when

replacing the battery. Have these procedures performed at the

intervals specified in the “Service Schedule.” A negative ground

system is used. Battery connections are shown on the wiring dia-

grams. Make sure the battery is correctly connected and terminals

are tight. Observe battery polarity when connecting the battery to

the generator set.

1.16 BATTERY CHARGER

NOTE:

The battery charger is integrated into the control module in all

models.

It operates as a "Smart Charger" which ensures output is continu-

ally optimized to promote maximum battery life and charging levels

are at safe conditions.

NOTE:

There is a warning on the LCD display when the battery needs

service.

2.1 ACTIVATE THE GENERATOR

When battery power is applied to the generator during the installa-

tion process, the controller will light up. However, the generator still

needs to be activated before it will automatically run in the event

of a power outage.

Activating the generator is a simple one time process that is guided

by the controller screen prompts. Once the product is activated,

the controller screen will not prompt you again, even if you discon-

nect the generator battery.

After obtaining your activation code, please complete the following

steps at the generator’s control panel as outlined by the Activation

Chart.

2.2 BEFORE INITIAL START-UP

NOTE:

These units have been run and tested at the factory prior to

being shipped and do not require any type of break-in.

NOTE:

This unit comes filled with oil from the factory. Check the oil

level and add the appropriate amount if necessary.

Before starting, complete the following:

1. Set the generator’s main circuit breaker to its OFF (or OPEN)

position.

2. Set the generator's AUTO/OFF/MANUAL switch to the OFF

position.

3. Turn OFF all breakers on the load center of the transfer box (T1

and T2).

4. Turn OFF all loads connected to the transfer switch terminals

T1 and T2.

5. Check the engine crankcase oil level and, if necessary, fill to

the dipstick FULL mark with the recommended oil. Do not fill

above the FULL mark.

6. Check the fuel supply. Gaseous fuel lines must have been

properly purged and leak tested in accordance with applicable

fuel-gas codes. All fuel shutoff valves in the fuel supply lines

must be open.

During initial start up only, the generator may exceed the normal

number of start attempts and experience an “over crank” fault (See

the "Overcrank" section). This is due to accumulated air in the fuel

system during installation. Reset the control board and restart up

to two more times, if necessary. If unit fails to start, contact the

local dealer for assistance.



Never operate the engine with the oil level

below the “Add” mark on the dipstick. Doing

this could damage the engine.

2.3 CHECK TRANSFER SWITCH

OPERATION

Refer to the "Manual Transfer Operation" section, of the owner’s

manual for procedures.



Do not attempt manual transfer switch opera-

tion until all power voltage supplies to the

transfer switch have been positively turned

off. Failure to turn off all power voltage sup-

plies will result in extremely hazardous and

possibly fatal electrical shock.

2.4 ELECTRICAL CHECKS

Complete electrical checks as follows:

1. Set the generator's main circuit breaker to its OFF (or OPEN)

position.

2. Set the generator's AUTO/OFF/MANUAL switch to the OFF

position.

3. Turn OFF all breakers on the load center of the transfer box (T1

and T2).

4. Turn on the utility power supply to the transfer switch using

the means provided (such as a utility main line circuit break-

er).



The transfer switch is now electrically

“hot.” Contact with “hot” parts will result in

extremely hazardous and possibly fatal

electrical shock. Proceed with caution.

5. Use an accurate AC voltmeter to check utility power source

voltage across transfer switch terminals N1 and N2. Nominal

line-to-line voltage should be 240 volts AC.

Post Installation Start-up and Adjustments

15

ACTIVATION CHART

CHOOSE LANGUAGE TROUBLESHOOTING

Display Reads: Use ARROW keys to scroll to desired lan-

guage. Press ENTER to select.

If the wrong language is chosen, it can be

changed later using the “edit” menu.

Display Reads: Press ENTER to begin the activation pro-

cess.

If ESCAPE is pressed instead of ENTER,

your generator will only run in manual mode

(for test purposes) and NOT ACTIVATED will

be displayed. You will need to remove the

generator control panel fuse AND disconnect

the T1, N1 and N2 connector in the external

connection box (if equipped); or disconnect

utility input (main breaker) to the transfer

switch for 3-5 seconds and reconnect, then

begin with Step 1.

Display Reads: If you do not have your activation code,

go to www.activategen.com or call

1-888-9ACTIVATE (922-8482).

If you already have your activation code,

wait 3-5 seconds for the next display.

ENTER ACTIVATION CODE (Passcode) TROUBLESHOOTING

Display Reads: Use ARROW keys to scroll and find the first

number of your Activation Code.

Press ENTER to select.

Repeat this step until all digits have been

entered.

Use ESCAPE to correct previous digits.

Display Reads: Activation is complete when all digits are

entered above and your screen shows this

display.

Follow the controller prompts to continue

setting the time function. Refer to your

Owner’s Manual with questions.

What happens if “Wrong Passcode Try

Again” appears?

Reenter the activation code. If a second

attempt is unsuccessful, check the number

against the code given on activategen.com.

If it is correct and the generator will not

accept it, contact 1-888-9ACTIVATE (922-

8482).

“SELECT HOUR (0-23)”

“- +”6

Escape Enter

Serial 123456789

Passcode XXXXX +/-

Escape Enter

To Activate go to

www.activategen.com

Escape Enter

Activate me (ENT) or

ESC to run in manual

Escape Enter

Language

- English +

Escape Enter

Post Installation Start-up and Adjustments

16

6. Check utility power source voltage across terminals N1 and

the transfer switch neutral lug; then across terminal N2 and

neutral. Nominal line-to-neutral voltage should be 120 volts AC.

7. When certain that utility supply voltage is compatible with

transfer switch and load circuit ratings, turn OFF the utility

power supply to the transfer switch.

8. On the generator panel, set the Auto/Off/ Manual switch to

MANUAL. The engine should crank and start.

9. Let the engine warm up for about five minutes to allow inter-

nal temperatures to stabilize. Then, set the generator’s main

circuit breaker to its ON (or closed) position.



Proceed with caution! Generator power volt-

age is now supplied to the transfer switch.

Contact with live transfer switch parts will

result in dangerous and possibly fatal electri-

cal shock.

10. Connect an accurate AC voltmeter and a frequency meter

across transfer switch terminal lugs E1 and E2. Voltage

should be 238-242 at a frequency of 59.5-60.5 Hertz.

11. Connect the AC voltmeter test leads across terminal lugs E1

and neutral; then across E2 and neutral. In both cases, voltage

reading should be 119-121 volts AC.

12. Set the generator’s main circuit breaker to its OFF (or OPEN)

position. Let the engine run at no-load for a few minutes to

stabilize internal engine generator temperatures.

13. Set the generator's AUTO/OFF/MANUAL switch to OFF. The

engine should shut down.

NOTE:

It is important not to proceed until certain that generator AC

voltage and frequency are correct and within the stated limits.

2.5 GENERATOR TESTS UNDER

LOAD

To test the generator set with electrical loads applied, proceed as

follows:

1. Set generator’s main circuit breaker to its OFF (or OPEN) posi-

tion.

2. Turn OFF all breakers on the load center of the transfer box (T1

and T2).

3. Set the generator's AUTO/OFF/MANUAL switch to OFF.

4. Turn OFF the utility power supply to the transfer switch,

using the means provided (such as a utility main line circuit

breaker).



Do not attempt manual transfer switch opera-

tion until all power voltage supplies to the

transfer switch have been positively turned

off. Failure to turn off all power voltage sup-

plies will result in extremely hazardous and

possibly fatal electrical shock.

5. Manually set the transfer switch to the STANDBY position, i.e.,

load terminals connected to the generator's E1/E2 terminals.

The transfer switch operating lever should be down.

6. Set the generator's AUTO/OFF/MANUAL switch to MANUAL.

The engine should crank and start immediately.

7. Let the engine stabilize and warm up for a few minutes.

8. Set the generator’s main circuit breaker to its ON (or CLOSED)

position. Loads are now powered by the standby generator.

9. Turn ON the load center of the transfer switch (T1 and T2).

10. Connect an accurate AC voltmeter and a frequency meter

across terminal lugs E1 and E2.

– Voltage should be greater than, or approximately 240 volts

and frequency should be 60 Hz.

11. Let the generator run at full rated load for 20-30 minutes.

Listen for unusual noises, vibration or other indications of

abnormal operation. Check for oil leaks, evidence of overheat-

ing, etc.

12. When testing under load is complete, turn OFF electrical

loads.

13. Set the generator's main circuit breaker to its OFF (or OPEN)

position.

14. Let the engine run at no-load for a few minutes.

15. Set the AUTO/OFF/MANUAL switch to OFF. The engine should

shut down.

2.6 CHECKING AUTOMATIC

OPERATION

To check the system for proper automatic operation, proceed as

follows:

1. Set generator’s main circuit breaker to its OFF (or OPEN) posi-

tion.

2. Check that the AUTO/OFF/MANUAL switch is set to OFF.

3. Turn OFF the utility power supply to the transfer switch, using

means provided (such as a utility main line circuit breaker).

4. Manually set the transfer switch to the UTILITY position, i.e.,

load terminals connected to the utility power source side.

5. Turn ON the utility power supply to the transfer switch,

using the means provided (such as a utility main line circuit

breaker).

6. Set the generator's main circuit breaker to its ON (or CLOSED)

position.

7. Set the AUTO/OFF/MANUAL switch to AUTO. The system is

now ready for automatic operation.

8. Turn OFF the utility power supply to the transfer switch.

With the AUTO/OFF/MANUAL switch at AUTO, the engine should

crank and start when the utility source power is turned OFF after a

10 second delay. After starting, the transfer switch should connect

load circuits to the standby side after a five (5) second delay. Let

the system go through its entire automatic sequence of operation.

With the generator running and loads powered by generator AC

output, turn ON the utility power supply to the transfer switch. The

following should occur:

• After about 15 seconds, the switch should transfer loads back

to the utility power source.

• About one minute after re-transfer, the engine should shut

down.

Post Installation Start-up and Adjustments

17

3.1 CONTROL PANEL INTERFACE

3.1.1 USING THE AUTO/OFF/MANUAL SWITCH

(FIGURE 3.1)



With the switch set to AUTO, the engine may

crank and start at any time without warning.

Such automatic starting occurs when utility

power source voltage drops below a preset

level or during the normal exercise cycle. To

prevent possible injury that might be caused

by such sudden starts, always set the switch

to OFF and remove the fuses before work-

ing on or around the generator or transfer

switch. Then, place a “DO NOT OPERATE”

tag on the generator panel and on the trans-

fer switch.

1. “AUTO” Position – Selecting this switch activates fully auto-

matic system operation. It also allows the unit to automati-

cally start and exercise the engine every seven days with the

setting of the exercise timer (see the Setting the Exercise

Timer section).

2. “OFF” Position – This switch position shuts down the engine.

This position also prevents automatic operation.

3. “MANUAL” Position – Set the switch to MANUAL to crank

and start the engine. Transfer to standby power will not occur

unless there is a utility failure.

3.1.2 SETTING THE EXERCISE TIMER

This generator is equipped with an exercise timer. Once it is set,

the generator will start and exercise every seven days, on the day

of the week and at the time of day specified. During this exercise

period, the unit runs for approximately 12 minutes and then shuts

down. Transfer of loads to the generator output does not occur

during the exercise cycle unless utility power is lost.

Figure 3.1 – 8 - 20kW Generator Control Panel

Escape

MAIN FUSE

AUTO OFF MANUAL

7.5 AMP

Enter

Installation Assistant

Interconnect System Self Test Feature (follow the on-screen

prompts)

Upon power up, this controller will go through a system self test

which will check for the presence of utility voltage on the DC

circuits. This is done to prevent damage if the installer mistakenly

connects AC utility power sense wires into the DC terminal block.

If utility voltage is detected, the controller will display a warning

message and lock out the generator, preventing damage to the

controller. Power to the controller must be removed to clear this

warning.

Utility voltage must be turned on and present at the N1 and N2

terminals inside the generator control panel for this test to be

performed and pass.

NOTE:

DAMAGE CAUSED BY MISWIRING OF THE INTERCONNECT

WIRES IS NOT WARRANTABLE!

This test will be performed each time the controller is powered up.

Upon first power up of the generator, the display interface will

begin an installation assistant. The assistant will prompt the user

to set the minimum settings to operate. These settings are sim-

ply: Current Date/Time and Exercise Day/Time. The maintenance

intervals will be initialized when the exercise time is entered (Figure

3.1).

The exercise settings can be changed at any time via the "EDIT"

menu (see Appendix, "Menu System").

If the 12 volt battery is disconnected or the fuse removed, the

Installation Assistant will operate upon power restoration. The only

difference is the display will only prompt the customer for the cur-

rent Time and Date.

IF THE INSTALLER TESTS THE GENERATOR PRIOR TO

INSTALLATION, PRESS THE “ENTER” KEY TO AVOID SETTING

UP THE EXERCISE TIME. THIS WILL ENSURE THAT WHEN

THE CUSTOMER POWERS UP THE UNIT, HE WILL STILL BE

PROMPTED TO ENTER AN EXERCISE TIME.

NOTE:

The exerciser will only work in the AUTO mode and will not work

unless this procedure is performed. The current date/time will

need to be reset every time the 12 volt battery is disconnected

and then reconnected, and/or when the fuse is removed.

Low Speed Exercise

16, 17 & 20kW units will run at 2,400 rpm.

Operation

18

Display Interface Menus

The LCD display is organized as detailed below:

• The “Home” page, this page is the default page which will be

displayed if no keys are pressed for 30 seconds. This page

normally shows the current Status message and the current

date and time. The highest priority active Alarm and/or Warning

will be automatically posted on this page as well as flashing

the backlight when such an event is detected. In the case of

multiple Alarms or Warnings, only the first message will be

displayed. To clear an Alarm or Warning, see the Protection

Systems section - Clear Alarm.

• The display backlight is normally off. If the user presses any

key, the backlight will come on automatically and remain on for

30 seconds after the last key was pressed.

• The “Main Menu” page will allow the user to navigate to all other

pages or sub-menus by using the Left/Right and Enter keys.

This page can be accessed at any time with several presses of

the dedicated Escape key. Each press of the Escape key takes

you back to the previous menu until the main menu is reached.

This page displays the following options: HISTORY; STATUS;

EDIT; AND DEBUG. (See the Appendix - "Menu System".)

3.2 AUTOMATIC TRANSFER

OPERATION

To select automatic operation, do the following:

1. Make sure the transfer switch main contacts are set to their

UTILITY position, i.e., loads connected to the utility power

source (Figure 3.1).

2. Be sure that normal UTILITY power source voltage is avail-

able to transfer switch terminal lugs N1 and N2 (Refer to the

Electrical Data section).

3. Set the generator’s AUTO/OFF/MANUAL switch to AUTO.

4. Set the generator’s main circuit breaker to its ON (or CLOSED)

position.

With the preceding steps complete, the generator will start auto-

matically when utility source voltage drops below a preset level.

After the unit starts, loads are transferred to the standby power

source. Refer to the Sequence of Automatic Operation section.

3.3 SEQUENCE OF AUTOMATIC

OPERATION

3.3.1 UTILITY FAILURE

Initial Conditions: Generator in Auto, ready to run, load being sup-

plied by utility source. When utility fails (below 60% of nominal),

a 10 second (optionally programmable) line interrupt delay time is

started. If the utility is still gone when the timer expires, the engine

will crank and start. Once started, a five (5) second engine warm-

up timer will be initiated. When the warm-up timer expires, the

control will transfer the load to the generator. If the utility power is

restored (above 80% of nominal) at any time from the initiation of

the engine start until the generator is ready to accept load (5 sec-

ond warm-up time has not elapsed), the controller will complete

the start cycle and run the generator through its normal cool down

cycle; however, the load will remain on the utility source.

3.3.2 CRANKING

The system will control the cyclic cranking as follows: 16 second

crank, seven (7) second rest, 16 second crank, seven (7) second

rest followed by three (3) additional cycles of seven (7) second

cranks followed by seven (7) second rests.

Choke Operation

1. The 990/999cc engines have an electric choke in the air

box that is automatically controlled by the electronic control

board.

2. The 530cc engines have an electric choke on the divider panel

air inlet hose that is automatically controlled by the electronic

control board.

3. The 410cc engines have a choke behind the air box that is

automatically controlled by the electronic control board.

Failure to Start

This is defined as any of the following occurrences during crank-

ing:

1. Not reaching starter dropout within the specified crank cycle.

Starter dropout is defined as four (4) cycles at 1,000 RPM.

2. Reaching starter dropout, but then not reaching 2200 RPM

within 15 seconds. In this case the control board will go into

a rest cycle for seven (7) seconds, then continue the rest of

the crank cycle.

During a rest cycle the start and fuel outputs are de-energized and

the magneto output is shorted to ground.

Cranking Conditions

The following notes apply during cranking cycle.

1. Starter motor will not engage within five (5) seconds of the

engine shutting down.

2. The fuel output will not be energized with the starter.

3. The starter and magneto outputs will be energized together.

4. Once the starter is energized the control board will begin look-

ing for engine rotation. If it does not see an RPM signal within

three (3) seconds it will shut down and latch out on RPM

sensor loss.

5. Once the control board sees an RPM signal it will energize the

fuel solenoid, drive the throttle open and continue the crank

sequence.

6. Starter motor will disengage when speed reaches starter

dropout.

7. If the generator does not reach 2200 RPM within 15 seconds,

re-crank cycle will occur.

8. If engine stops turning between starter dropout and 2200

RPM, the board will go into a rest cycle for seven (7) seconds

then re-crank (if additional crank cycles exist).

9. Once started, the generator will wait for a hold-off period

before starting to monitor oil pressure and oil temperature

(refer to the Alarm Messages section for hold-off times).

10. During Manual start cranking, if the Mode switch is moved

from the Manual position, the cranking stops immediately.

11. During Auto mode cranking, if the Utility returns, the cranking

cycle does NOT abort but continues until complete. Once the

engine starts, it will run for one (1) minute, then shut down.

Operation

La page charge ...

Generac 16 kW 0058941 Manuel utilisateur

Generac 16 kW 0058941 Manuel utilisateur

dans d''autres langues