INSTALLATION
INSTRUCTIONS
with Design Guide
Double-Drawer Built-In
Refrigerator
Monogram.com
Safety Information
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
IMPORTANT – Save these instructions for
local inspector’s use. Observe all governing codes and
ordinances.
• Note to Installer – Be sure to leave these instructions
with the Consumer.
• Note to Consumer – Keep these instructions with your
Owner’s Manual for future reference.
If you received a damaged refrigerator, you should
immediately contact your dealer or builder.
Skill Level – Installation of this refrigerator requires
basic mechanical, carpentry and plumbing skills. Proper
installation is the responsibility of the installer. Product
failure due to improper installation is not covered under
the GE Appliance Warranty. See the Owner’s Manual for
warranty information.
WARNING
Explosion Hazard. Keep flammable materials and vapors, such as gasoline, away from
refrigerator. Failure to do so can result in fire, explosion, or death.
WARNING
To reduce the risk associated with choking, do not allow children under 3 years of age to have
access to small parts during the installation of this product.
For Monogram local service in your area, call 800.444.1845 or visit monogram.com.
For Monogram service in Canada, call 888.880.3030
For Monogram Parts and Accessories, call 800.444.1845 or visit monogram.com.
For Monogram Parts and Accessories in Canada, call 888.880.3030 or visit monogram.ca.
CONNECTING ELECTRICITY
WARNING
Electrical Shock Hazard.
Plug into a grounded 3-prong outlet.
Do not remove the ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped with a
3-prong (grounding) plug which mates with a standard
3-prong (grounding) wall outlet to minimize the possibility
of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it
is your personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall outlet. Do
not use an adapter.
The refrigerator should always be plugged into its own
individual electrical outlet which has a voltage rating that
matches the rating plate.
A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded
electrical supply is required. This provides the best
performance and also prevents overloading house wiring
circuits which could cause a fire hazard from overheated
wires.
Never unplug your refrigerator by pulling on the power
cord. Always grip plug firmly and pull straight out from the
outlet.
Immediately discontinue use of a damaged
supply cord. If the supply cord is damaged
it must be replaced by a qualified service
professional with an authorized service part
from the manufacturer.
When moving the refrigerator away from
the wall, be careful not to roll over or
damage the power cord.
2 31-51545-5
3
Consignes de Sécurité
AVERTISSEMENT
Risque d’explosion.
Conservez les matériaux et vapeurs inflammables tels que l’essence à l’écart de votre réfrigérateur. Le non-respect de
cette instruction peut entraîner un risque d’incendie, d’explosion ou de décès.
AVERTISSEMENT
Pour réduire le risque d’étouffement pendant l’installation de ce produit, ne pas laisser les
petites pièces à la portée des enfants âgés de moins de 3 ans.
AVERTISSEMENT
Risque d’électrocution.
Branchez l’appareil dans une prise à 3 broches mise à la terre.
N’enlevez pas la broche de mise à la terre.
N’utilisez pas un adaptateur.
N’utilisez pas un cordon de rallonge.
Le non-respect de ces instructions peut entraîner des risques d’incendies, des chocs électriques ou la mort.
BRANCHEMENTS ÉLECTRIQUES
Ne coupez pas ou n’enlevez pas, sous aucun prétexte, la troisième broche de mise à la terre du cordon
d’alimentation. Pour des raisons de sécurité, cet appareil doit être correctement mis à la terre.
Le cordon d’alimentation de cet appareil est équipé d’une
fiche à trois broches (pour une mise à la terre) qui s’adapte
à la prise de courant standard à 3 broches (pour une mise
à la terre) pour minimiser les risques de chocs électriques
par cet appareil.
Faites vérifier la prise murale et le circuit électrique par
un électricien qualifié pour s’assurer que le système est
correctement mis à la terre.
Dans le cas d’une prise biphasée, l’installateur a la
responsabilité et l’obligation de la remplacer par une prise
triphasée correctement mise à la terre. N’utilisez pas
d’adaptateur.
Le réfrigérateur doit toujours être branché à sa propre
prise électrique d’une tension nominale correspondant à
celle indiquée sur sa plaque signalétique.
Une alimentation électrique à 115 volts CA, 60 Hz, avec
un fusible de 15 ou 20 ampères et une mise à la terre est
nécessaire. Ceci permet d’obtenir un meilleur rendement
et évite de surcharger les circuits électriques du domicile
qui risque d’occasionner un incendie en surchauffant.
Ne débranchez jamais le réfrigérateur en tirant sur le
cordon d’alimentation. Prenez toujours fermement la fiche
en main et tirez pour la sortir de la prise.
Cessez immédiatement l’utilisation d’un
cordon électrique endommagé. Si le
cordon électrique est endommagé, son
remplacement doit être exécuté par un
technicien en réparation qualifié au moyen
d’un cordon de rechange autorisé par le
fabricant.
Lorsque vous éloignez votre réfrigérateur
du mur, faites attention à ne pas le faire
rouler sur le cordon d’alimentation afin de
ne pas l’endommager.
31-51545-5 3
CONTENTS
Important Information
Tools, Hardware ....................................................... 4
Parts Required .......................................................... 4
Caring for Your Stainless Steel ................................. 4
Design Guide (for ZIDS240)
The Installation Space ............................................... 5
Product Clearances ................................................... 5
Side-by-Side Installations ......................................... 5
Design Guide (for ZIDI240)
The Installation Space ............................................... 6
Product Clearances ................................................... 6
Side-by-Side Installations ......................................... 6
Installation Instructions
Step 1, Remove Packaging ....................................... 7
Step 2, Install Custom 3/4"
Drawer Panels and Handles
(ZIDI240 model only) ............................................. 7, 8
Step 3, Level ............................................................. 8
Step 4, Connect Power ............................................. 9
Step 5, Slide Product into Cutout ..............................9
Step 6, Set Temperature Controls ............................ 9
Important Information
ZIDI240 MODEL ONLY
PARTS REQUIRED
• Custom handles
• Overlay panels
• Spacer panels
• Backer panels
• Screws
PARTS SUPPLIED
• Drawer side trims
• Optional black or
stainless steel toekick
TOOLS REQUIRED
• Adjustable wrench
• Carpenter’s glue (ZIDI240 model only)
• Screwdriver (ZIDI240 model only)
CARING FOR YOUR STAINLESS
STEEL
• Before installation or first use, we strongly advise you
polish the stainless steel exterior and handles with a
commercially available stainless steel cleaner such
as Stainless Steel Magic
™
. To preserve and protect
the fine finish, we also strongly advise that you apply
stainless steel cleaner monthly.
REFRIGERATOR LOCATION
• Do not install the refrigerator where the temperature
will go below 55°F (12.7°C) because it will not run
often enough to maintain proper temperatures.
• Do not install the refrigerator where the temperature
will go above 100°F (37°C) because it will not
perform properly.
• Do not install the refrigerator in a location exposed to
water (rain, etc.) or direct sunlight.
• Install it on a floor strong enough to support it fully
loaded.
4 31-51545-5
Design Guide
THE INSTALLATION SPACE
IMPORTANT: Double-Drawer Refrigerators are
designed to be built-in only. They cannot be used
free-standing.
The cutout depth should be 24”
NOTE: The unit is designed to be flush with the
surrounding cabinets.
Additional Specifications
• A 120 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch circuit
or circuit breaker is recommended. Install a properly
grounded 3-prong electrical receptacle recessed into
the back wall as shown. Electrical must be located on
rear wall as shown. NOTE: GFCI (ground fault circuit
interrupter) is not recommended.
PRODUCT CLEARANCES
When installed in a corner:
Allow 2-1/2" min. clearance between Double-Drawer
and adjacent cabinet, wall or other appliances. Allow
22" min. clearance from the front for drawer opening.
NOTE: Clearances are based on the noted 2-1/8"
handle standoff depth.
• Test the drawer openings. Carefully open and close
the drawers. The drawers should not rub or catch on
adjacent cabinetry. Notify the installer if the drawers
make contact with cabinetry.
Choose the location:
• These products may be closed in on the top and
three sides as long as the front is unobstructed for air
circulation and proper access to the drawers.
• Do not install these products where the temperature
will go below 55°F (13°C) or above 100°F (37°C).
• These products are not designed to be stacked one over
the other.
SIDE-BY-SIDE INSTALLATIONS –
Stainless Steel Models Only
For a complete refreshment center, install a Double-
Drawer Refrigerator beside a Beverage Center, Wine
Chiller/Wine Reserve, Fresh-Food Refrigerator or Bar
Refrigerator with Icemaker.
• A side-by-side installation requires at least a 47-1/2"
wide opening. No trim kits required.
• Products must operate from separate, properly
grounded receptacles.
34-1/2"-35"
47-1/2" Min.
1-1/2"
9"
10-1/2"
9"
10-1/2"
14"
15"
Locate
Outlet
24"
23-3/4"
34-1/4"
25-7/8"
Including
Handles
Locate
Outlet
34-1/2"-35"
24"
23-3/4" Min.
1-1/2"
9"
Max.
8-1/2"
9" Max.
10-1/2"
1-1/2"
to 34-3/4"
34-1/4"
to 34-3/4"
NOTE:
Handle and
handle standoff
depth is 2-1/8"
FOR MODEL ZIDS240 WITH STAINLESS STEEL DRAWERS AND HANDLES
Clearance for Door
Opening 2-1/2" min.
Countertop
Double-Drawer
22" min.
31-51545-5 5
Design Guide
PRODUCT CLEARANCES
When installed
in a corner:
Allow 2-1/2" min. clearance between Double-Drawer and
adjacent cabinet, wall or other appliances. Allow 23-1/8"
min. clearance from the front for drawer opening.
NOTE: Custom handle clearances may vary depending on
the standoff of the custom handles.
• Test the drawer openings. Carefully open and close
the drawers. The drawers should not rub or catch on
adjacent cabinetry. Notify the installer if the drawers
make contact with cabinetry. NOTE: When installing
custom panels and handles, use above clearances as a
general guide but adjust according to the installation.
Choose the location:
• These products may be closed in on the top and
three sides as long as the front is unobstructed for air
circulation and proper access to the drawers.
• Do not install these products where the temperature will
go below 55°F (13°C) or above 100°F (37°C).
• These products are not designed to be stacked one over
the other.
Black or Stainless Steel Toekick Options
• These products are shipped with two toekicks, a stainless
steel and a black toekick. For shipping purposes, one of
the toekicks will be secured to the back of the unit and
the second will be installed, in place, on the unit. Keep
the unused toekick, and other unused or removed parts,
for future use.
FOR MODEL ZIDI240 WITH CUSTOM DRAWER PANELS AND HANDLES
Clearance for Door
Opening 2-1/2" min.
Countertop
Double-Drawer
23-1/8" min.
SIDE-BY-SIDE INSTALLATIONS –
Custom Panel Models Only
For a complete refreshment center, install a Double-
Drawer Refrigerator beside a Beverage Center or Wine
Chiller/Wine Reserve.
• A side-by-side installation requires at least a 47-1/2"
wide opening. No trim kits required.
• Products must operate from separate, properly
grounded receptacles.
34-1/2"-35"
47-1/2" Min.
1-1/2"
9"
10-1/2"
9"
10-1/2"
14"
15"
Locate
Outlet
24"
* NOTE: Additional
clearances may be required.
THE INSTALLATION SPACE
IMPORTANT: Double-Drawer Refrigerators are
designed to be built-in only. They cannot be used
free-standing.
The cutout depth should be 24”
The cutout dimensions shown allow for full drawer
extension.
NOTE: The unit is designed to be flush with the
surrounding cabinets.
Additional Specifications
• A 120 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install
a properly grounded 3-prong electrical receptacle
recessed into the back wall as shown. Electrical must
be located on rear wall as shown. NOTE: GFCI
(ground fault circuit interrupter) is not recommended.
23-3/4"
24-7/8"
34-1/4"
Locate
Outlet
34-1/2"-35"
24"
23-3/4" Min.
1-1/2"
9"
Max.
8-1/2"
9" Max.
10-1/2"
1-1/2"
to 34-3/4"
NOTE: Handles
not supplied.*
* Custom handle clearances may vary, depending on the
standoff of the custom handles.
6 31-51545-5
Installation Instructions
STEP 1 REMOVE PACKAGING
AND INSTALLATION PARTS
• Remove corner blocks and foam drawer stops.
• Remove all packing material, tape and protective
plastic coverings.
WARNING
Small objects are a choke hazard for
children. Remove and discard any parts not used.
AVERTISSEMENT
Les petits objets peuvent
étrangler les enfants. Il faut jeter toutes les pièces qui
ne sont pas utilisées.
STEP 2 INSTALL CUSTOM 3/4”
DRAWER PANELS AND
HANDLES (CONT.)
(ZIDI240 model only)
Install custom drawer panels and handles:
• Open drawers.
• Remove 2 screws holding each trim; lift trims off.
Retain screws.
•
Custom handles of your choice, supplied by your
cabinet maker, must be installed onto the overlay
panels before they are slid into the trims. Countersink
all screws into the backer panels. Screws cannot
protrude from the backer panels.
•
Slide overlay panels into the trims.
STEP 2 INSTALL CUSTOM 3/4”
DRAWER PANELS AND
HANDLES
(ZIDI240 model only)
3/4” Overlay Panel Dimensions
Model ZIDI240 requires field-installed
overlay drawer panels.
• The overlay panels must be secured
to 1/4” thick backer panels that slide
into the trims. A .10” thick spacer
panel must be placed between the
overlay and backer panels.
• Custom handles of your choice,
supplied by your cabinet maker,
must be installed on these overlay
panels. Countersink all screws into
the backer panels. Screws cannot protrude from the
backer panels.
IMPORTANT NOTE: Maximum total weight for custom
drawer panels are 25 pounds (12-1/2 pounds maximum
each drawer).
Assemble overlay panels with glue and screws.
• Center spacer panel on the
backer panel, left to right and
top to bottom. Secure the panels
with glue.
• Center the spacer/backer
panel on the overlay panel.
Secure with glue and screws.
Countersink all screws into the
backer panel.
Overlay
Panel
1/4"
Backer
Panel
Drawer
.10 Inch
Spacer
3/4" Overlay Panel Dimensions (in inches)
A (Width) B (Height)
1/4" Backer 23-3/16" 14-11/16"
0.10" Spacer 22-1/2" 14-3/16"
3/4" Overlay 23-5/8" 15-1/16"
A
B
B
12-1/2 lbs. max.
12-1/2 lbs. max.
*
*Maintain a 1/4" min. gap between
top and bottom drawer panels.
Spacer Panel
Backer Panel
Overlay Panel
Handle
Custom
Drawer Panel
Screws Must
Be Countersunk
Into Panel
31-51545-5 7
Installation Instructions
STEP 2 INSTALL CUSTOM 3/4”
DRAWER PANELS AND
HANDLES
(CONT.)
(ZIDI240 model only)
• Reinstall the side trims using the trim screws removed
earlier.
• Place the brushed decorative covers over the side trim
to hide the screw heads. Ensure side trim is aligned
top to bottom and front to back. Snap into place.
NOTE: For shipping purposes, the brushed decorative
cover will be secured to the front of the unit.
STEP 3 LEVEL
Use an adjustable wrench to turn and raise or lower the
leveling legs.
• Measure floor to countertop height inside the opening.
Adjust leveling legs until the product is approximately
1/8” less than countertop height.
INSTALLATION TIP:
Measure floor to underside of countertop inside
the opening.
• If the room floor is higher than the floor inside the
opening, adjust the rear leveling legs to approximately
1/8” less than the opening height. Screw front leveling
legs all the way in to shorten the height at the front.
This will allow you to slightly tip the unit into the
opening. Once the unit is in the correct position,
the front legs can be adjusted to level the product.
Turn Right to Lower
Turn Left to Raise
8 31-51545-5
Installation Instructions
STEP 4 CONNECT POWER
• Connect power cord plug to a properly grounded
receptacle.
• Check to make sure power is on by opening a drawer
to see if interior light turns on.
• The interior fan runs all the time except when a drawer
is open.
See the Owner’s Manual for further explanation of the
fan.
STEP 6 SET TEMPERATURE
CONTROLS
• The temperature controls are preset. Refer to the
Owner’s Manual for more information. Allow 12–24
hours for the temperature to stabilize.
NOTE: The Double-Drawer Refrigerator operates very
quietly. You may not notice the unit running, and when
first installed, the fans and motor may not come on
immediately – this is normal. If the display is lit and the
light is working, the unit is operating.
STEP 5 SLIDE PRODUCT INTO
THE CUTOUT
NOTICE: Do not push against the drawer panels with
your knees. Do not push or lift the unit by the drawer
handles. Damage may occur!
• Open one of the drawers and gently push the unit
back into the opening with your hands against the
sides. Be careful not to entangle power cord.
• Check again to be sure the unit is level. Adjust the
leveling legs until the unit is resting firmly against
the bottom of the counter to prevent rocking or
movement during operation.
• If alignment with adjacent cabinetry is an issue, use
a shim to secure the unit against the underside of the
countertop.
31-51545-5 9
Notes
10 31-51545-5
Notes
31-51545-5 11
NOTE: While performing installations described in this
book, safety glasses or goggles should be worn.
NOTE: Product improvement is a continuing endeavor
at Monogram. Therefore, materials, appearance and
specifications are subject to change without notice.
31-51545-5
02-19 GEA
Monogram.com
Printed in Serbia
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
dans d''autres langues
- English: GE ZIDS240NSS Installation guide
