Glacier Bay HD873X-1027H2 Guide d'installation

THANK YOU

INSTALLATION AND CARE GUIDE

SINGLE-HANDLE TUB AND SHOWER FAUCET

We appreciate the trust and condence you have placed in Glacier Bay through the purchase of this tub and

shower faucet. We strive to continually create quality products designed to enhance your home. Visit us online

to see our full line of products available for your home improvement needs. Thank you for choosing Glacier Bay!

HOMEDEPOT.COM

Questions, problems, missing parts?

Before returning to the store, call Glacier Bay Customer Service

8 a.m. - 7 p.m., EST, Monday - Friday

9 a.m. - 6 p.m., EST, Saturday

1-855-HD-GLACIER (1-855-434-5224)

HOMEDEPOT.COM

8/2017 REV.01

Model#

HD873X-1001

HD873X-1004

HD873X-1027H2

SKU#

1003015371

1003002587

1003002782

Internet#

304367659

304367710

304367675

2

Table of Contents

Important Information ..............................2

Warranty ...................................................2

Pre-Installation .........................................3

Planning Installation ..............................3

Package Contents ..................................6

Installation ................................................7

Care and Cleaning ....................................14

Troubleshooting ........................................15

Service Parts

...........................................

16

Important Information

□ Do not install this product until you read and understand the instructions in this manual. If you are installing this

product for someone else, leave this manual for the owner’s/ user’s reference.

□ Inlet ports are designed to allow for 1/2 in. COPPER tubing solder connection or 1/2 in. IPS threading coupling

connection. For threaded connections, wrap sealant tape around threaded ends before connecting. If soldering

connections, certain inammable parts should be removed prior to the soldering in order to avoid heat damage.

If you are unsure how to properly remove these parts, please call us at 1-855-HD-Glacier.

□ Protect your eyes with safety glasses when cutting or soldering water supply lines.

□ NOISE AND WATER HAMMER IN PEX SYSTEMS: Due to the inherent exibility of PEX compared with metallic

plumbing materials, water hammer and noise can sometimes occur from the pressure surges. It is important to

ensure the tubing is not in contact with wallboard, forced air ducts or other high-resonance materials. Clamping

or strapping can help prevent these noises. DO NOT USE PEX tubing from the valve to the tub spout.

Tools and Hardware Required ...............3

Warranty

LIMITED LIFETIME WARRANTY

Glacier Bay products are manufactured with superior quality standards and workmanship and are backed by our

limited lifetime warranty. Glacier Bay products are warranted to the original consumer purchaser to be free of

defects in materials or workmanship. We will replace FREE OF CHARGE any product or parts that proves defective.

Simply, return the product / part to any of The Home Depot retail locations or call 1-855-HD-GLACIER (1-855-434-

5224) to receive the replacement item. Proof of purchase (original sales receipt) from the original consumer

purchaser must be made available for all Glacier Bay warranty claims.

This warranty excludes incidental/inconsequential damages and failures due to misuse, abuse or normal wear and

tear. This warranty excludes all industrial, commercial and business usage, whose purchasers are hereby extended

a ve year limited warranty from the date of purchase, with all other terms of this warranty applying except the

duration of warranty.

Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitations may not apply to you. This warranty gives you specic legal rights and you may also have other

rights that vary from state to state and province to province. Please see a store or contact 1-855-HD-GLACIER for

more details.

Contact the Customer Service Team at 1-855-434-5224 or visit www.HomeDepot.com.

3

Safety

goggles

Thread

sealant tape

Tube

cutter

Strap wrench

Adjustable

wrench

Measuring

tape

Thermometer

Phillips

screwdriver

Flathead

screwdriver

SILICONE

Silicone

sealant

Pre-Installation

PLANNING INSTALLATION

Before beginning the installation of this product, ensure all parts are present. Compare parts with the Package

Contents list. If any part is missing or damaged, do not attempt to install the product. Contact Customer Service

for replacement parts.

TOOLS AND HARDWARE REQUIRED

ADVANCED INSTALLATION: Consult a plumber or

professional before installing this product.

If you are replacing your plumbing valve, please review the four common plumbing methods illustrated below:

COPPER, IPS, PEX and CPVC. Remove the existing handle and valve trim before replacing your valve. Please follow

all local building and plumbing codes.

A. COPPER (Before soldering, remove the cartridge & stop valves from the valve)

Torch Lead-free solder Kit

Key

hole saw

Wire

brush

All installations can vary depending on how your previous faucet was installed. Not all supplies for faucet

installation are included; however, they are available wherever plumbing supplies are sold. When choosing your

installation supplies, make sure they are UPC and/or CSA approved products.

Flashlight

HOMEDEPOT.COM

Please contact 1-855-HD-GLACIER for further assistance.

Pre-Installation (continued)

4

Safety

goggles

Thread

sealant tape

Tube

cutter

Strap wrench

Adjustable

wrench

Measuring

tape

Thermometer

Phillips

screwdriver

Flathead

screwdriver

SILICONE

Silicone

sealant

B. IPS

Key

hole saw

Flashlight

C. PEX+COPPER

Safety

goggles

Thread

sealant tape

Tube

cutter

Strap wrench

Adjustable

wrench

Measuring

tape

Thermometer

Phillips

screwdriver

Flathead

screwdriver

SILICONE

Silicone

sealant

Key

hole saw

Flashlight

Full circle

crimping tool

Pipe

wrench

COPPER

Pre-Installation (continued)

5

D. CPVC+COPPER

Safety

goggles

Thread

sealant tape

Tube

cutter

Strap wrench

Adjustable

wrench

Measuring

tape

Thermometer

Phillips

screwdriver

Flathead

screwdriver

SILICONE

Silicone

sealant

Key

hole saw

Flashlight

CPVC

cleaner

P

i

p

e

J

o

i

n

t

C

o

m

p

o

u

n

d

CPVC

cement

P

i

p

e

J

o

i

n

t

C

o

m

p

o

u

n

d

COPPER

HOMEDEPOT.COM

Please contact 1-855-HD-GLACIER for further assistance.

6

Pre-Installation (continued)

PACKAGE CONTENTS

Part Description Quantity

A

1

B Shower arm 1

C Shower head 1

D Valve body 1

E Escutcheon 1

F Handle 1

G Index 1

H Screw 1

Shower ange

I Plug 1

J Tub spout 1

K Screw 2

L Plaster guard 1

M Escutcheon screw 2

N Protective cap 1

D

E

F

I

J

L

K

N

M

A

B

C

G

H

7

Installation

1

Preparing for installation

CAUTION: Always shut off the water supply before

removing an existing faucet or replacing any part of a

faucet. Open the faucet handle to relieve water pressure

and ensure that the water is completely shut off.

30 in.

Tub & Shower

8 in. Min.

48 in.

Shower Only

1 1/4 in. Diamter

1 1/4 in. Diameter

48 in.

Tub & Shower

Refer to

the step 2

30 in.

Shower Only

D

2

1-1/2 in. to 2-1/4 in.

Finished wall

6 in. dia.

D

3-3/8 in. to 6 in. dia.

Finished wall

D

L

Installing the valve body and

removing the plaster guard

□ Shut off the water supply to the tub and

shower.

□ Verify that the hole sizes and positions of the

holes in the wall are correct

□ The shower and tub spout outlet holes

should be 1-1/4 in. diameter.

□ Refer to Step 2 for valve access hole

dimensions.

□ The recommended valve depth to the

nished wall is 1-1/2 in. min. to

2-1/4 in. max.

□ Ensure that the valve body (D) cover is ush

with the nished exterior surface of the wall.

Position the valve body (D) correctly in the

wall with the side marked "UP" pointing up. The

8 in. minimum from the valve body (D) to the tub

spout (J) is required for proper operation.

A. Thin Wall Installation

“Thin Walls” are usually built up with materials

such as berglass tub surrounding them and will

be the main source of support for the valve. The

plaster guard (L) remains attached to the valve.

□

B. Thick Wall Installation

“Thick Walls” are usually built up with materials such

as cement board, drywall, tile, etc. The plaster guard

(L) is positioned so that it is ush with the nished

wall. This ensures that the valve will be at the correct

position to accept the trim. The depth for the valve

body (D) in wall is measured from the center of the

shower outlet to the nished wall surface. The

accepted depth distance is 1-1/2 in. to 2-1/4 in.. When

the depth distance is 1-1/2 in. to 1-3/4 in., there will

be interference between the plaster guard (L) and

escutcheon (E). It is recommended that you remove

the plaster guard (L) after the wall installation.

□

Unscrew the screws (K), and remove the plaster

guard (L).

□

NOTE: Be sure to position the valve body (D) correctly in

the wall, with the side marked "UP" facing upward.

HOMEDEPOT.COM

Please contact 1-855-HD-GLACIER for further assistance.

L

K

8

Installation (continued)

3

Installing the supply

connections

□

□ Tighten the pipes to the valve body (D) with a

pipe wrench (not included).

Wrap thread sealant tape (not included) around

the pipe threads in a clockwise direction, as

shown.

□

Connect the hot and cold water supply lines (1,

not included), the shower outlet pipe (2, not

included), and tub outlet pipe (3, not included)

by threading them into the valve body (D) in a

clockwise direction.

Connect the pipe elbows (4, not included) to

the end of the shower outlet and tub outlet

pipes.

□

NOTE: The hot water supply lines go into the "H" inlet, and

the cold water supply lines go into the "C" inlet. Do not use

PEX or CPVC between the valve body (D) and tub spout (J).

NOTE: If you do not wish to install the tub outlet, insert

the plug (I) into the bottom of the valve body (D).

4

Back to back installation

NOTE: Never install the valve body (D) upside down!

□ If the hot and cold inlets are reversed (hot on

right and cold on left), remove the screw (1),

inverter (2), sleeve (3), and bonnet (4) from the

valve body (D) with reversed supply connections.

Rotate the cartridge (5) 180°, so H appears on

the right. Install the cartridge making sure that

the key is fully engaged with the slot in the

valve body (D). Slide the bonnet (4) over the

cartridge (5) and thread them onto the valve

body (D). Hand tighten securely. Reassemble

the sleeve (3), inverter (2) and screw (1). If you

are not making a reverse or back to back

installation, skip this step and continue with

the step 5.

Cold

Hot

Normal

installation

(changes

not required)

Reverse

installation

Normal installation

Reverse installation

D

1

2

3

4

5

H

Hot

Cold

H

D

N

3

2

D

1

4

I

2

D

1

4

9

Installation (continued)

6

Installing the plaster guard

Place the plaster guard (L) onto the valve body (D)

and secure with the screws (K).

□

5

Flushing the water outlets

□

and checking for leaks

Place the handle (F) on the valve body (D)

inverter and turn the handle (F) to the full on

mixed position. Turn on the hot and cold water

supply lines and allow the water to ow from

the outlets for one minute, or until all foreign

matter has been ushed out. Check for leaks.

Shut off the water at the faucet and supply

lines. Remove the handle (F).

□

Loosen the screw (H). □

NOTE: Be sure to position the plaster guard (L) correctly

onto the valve body (D), with the side marked "SHOWER"

facing upward.

HOMEDEPOT.COM

Please contact 1-855-HD-GLACIER for further assistance.

D

K

L

D

H

F

10

Installation (continued)

7

Installing the shower arm

□ Insert the long end of the shower arm (B) through

the shower ange (A), and wrap thread sealant

tape (not included) around the long end of the

shower arm (B) in a clockwise direction, as

shown.

Install the long end of the shower arm (B)

into the pipe elbow inside the wall. Carefully

tighten the shower arm (B) with a clean strap

wrench. Do not over tighten.

□

Wrap thread sealant tape around the pipe

threads of the tub spout outlet (1, not included)

in a clockwise direction, as shown.

□

Connect the tub spout outlet pipe (the tub

spout outlet pipe should project 4 in. to 4-5/32 in.

from the nished wall) to the lower pipe elbow

(2, not included). Tighten the elbow and tub

spout outlet pipe connections with a strap

wrench.

□

8

Installing the tub spout

□

Wrap thread sealant tape around the pipe

threads of the tub spout (J) outlet in a clockwise

direction, as shown.

Thread the tub spout (J) onto the threaded

connection in a clockwise direction until the tub

spout (J) becomes ush with the nished wall.

□

Use the strap wrench to tighten the tub spout (J).

4 in. to 4-5/32 in.

Wall

1

2

B

A

J

11

Installation (continued)

□ Unscrew the sleeve (1) from the valve body (D).

□ Remove the inverter (2) from the valve body (D).

10

Adjusting the temperature

9

Removing the plastic cap

□ Before installing the escutcheon (E), remove the

plastic cap (1) from the valve body (D) by twisting

the cap in a clockwise direction when the depth

distance (which is measured from the center of

the shower outlet to the nished wall surface) is

1-3/4 in. to 2-1/4 in.. Or unscrew the screws (K)

and remove the plaster guard (L) when the depth

distance (which is measured from the center of

the shower outlet to the nished wall surface)

is 1-1/2 in. to 1-3/4 in..

NOTE: The limiter on the valve can be set to allow partial

or full access to hot water by limiting how far the handle

can be turned to the hot side of the valve. The limiter is

typically set at the factory to allow only warm water to pass

through the valve. Follow the directions in this section if you

wish to adjust the amount of hot water that is allowed

through the valve. If you do not wish to adjust the amount

of hot water that is allowed through the valve, proceed to

the step 11, and skip over the step 10 (A, B, C).

A

Removing the sleeve and

inverter

D

2

1

HOMEDEPOT.COM

Please contact 1-855-HD-GLACIER for further assistance.

OR

1

D

K

L

12

Installation (continued)

10

Adjusting the temperature

C

Adjusting the desired maximum

water temperature

□ For colder water, adjust the red limit stop ring (1) in a clockwise direction and reinstall the red limit stop

ring (1) onto the cartridge assembly (2).

□ For hotter water, adjust the red limit stop ring (1) in a counterclockwise direction and reinstall the red

limit stop ring (1) onto the cartridge assembly (2).

B

Removing the red limit stop ring

□ Remember the position of the red limit stop ring (1)

on the cartridge assembly (2). Remove the red limit

stop ring (1) from the cartridge assembly (2).

NOTE: A thermometer (not included) can be held in the

running water to aid in reaching the desired water

temperature.

For hotter water

For colder water

1

2

1

2

1

2

Installation (continued)

10

Adjusting the temperature

13

D

Reinstalling the inverter and

sleeve

□ Place the inverter (2) onto the valve body (D)

and rotate the inverter (2) with notch facing

down.

□ Screw the sleeve (3) onto the valve body (D).

NOTE: Rotate the cartridge stem (1) clockwise to turn off

the water before you install the handle.

11

Installing the escutcheon

and handle

□ Install the escutcheon (E) onto the valve body

(D) using the escutcheon screws (M).

Place the handle (F) onto the valve body (D)

and tighten with the screw (H). Insert the

index (G).

□

D

2

3

1

HOMEDEPOT.COM

Please contact 1-855-HD-GLACIER for further assistance.

D

F

M

E

H

G

Installation (continued)

13

Installing the shower head

□ Attach the shower head (C) to the shower arm

(B). Hand-tighten only.

12

Checking for leaks

□

Turn the handle (F) to the full on mixed position.

When the valve body (D) is turned on, water

normally ows through the tub spout (J). To

activate the shower, turn the valve on and pull

the knob (1) up. Hold the knob (1) until the water

ows continuously from the shower arm (B).

Check for leaks.

Shut off the water at the faucet and supply lines. □

14

Care and Cleaning

□ To clean, wipe down with a damp cloth and dry with a towel.

□ Do not use abrasive cleaners, steel wool, or harsh chemicals when cleaning this faucet, or the warranty will

be voided.

UP

FOR

SHOWER

1

J

F

D

B

J

B

C

15

Troubleshooting

NOTE: Refer to the Service Parts section in this manual

for a detailed drawing showing the location of the parts

listed below.

Problem Possible Cause Solution

Hot and cold are reversed. The lines are reversed or the cartridge is

installed upside down.

□ Rotate the cartridge stem 180°

so that the notch is facing down

towards the drain.

There is no ow or a low

water ow.

□ Turn both water supply valves

counterclockwise to the on

position.

There is leaking or dripping

from the spout when the

handle is closed.

The grommets are not sealing properly. □ Replace the cartridge.

One or both water supplies are not turned

on.

Water comes out of the

tub spout and showerhead

at the same time.

If the pattern of the water ow switches to

the shower from the tub spout, and the leak

from the tub spout is less than 0.01 GPM,

this is a normal occurrence. Or consider the

causes below:

! The pipe used between the valve and the

tub spout is not 1/2 in. IPS, or the COPPER

pipe is incorrect.

! The distance between the valve and the

showerhead is less than 48 in..

! There is a restriction between the valve

and the tub spout.

! The valve is installed upside down.

□ Change the pipe to IPS or

COPPER.

□ The distance from the

showerhead and valve moved

to at least 48 in..

□ Remove the tub spout and ush

out debris and/or replace the

undersized line or ttings.

□ Remove the valve and reinstall it

using the correct orientation.

The temperature range is

restricted.

The temperature limit stop is out of position. □ Refer to the section Adjusting

the Temperature.

The handle cannot be

installed or the handle rubs

against the escutcheon.

The valve is installed too far back from the

nished wall.

□ Reinstall the valve (refer to Step

2 of the Installation section).

The handle is hard to turn. The bonnet nut is too tight. □ Loosen the bonnet nut and

reinstall it. Do not overtighten.

HOMEDEPOT.COM

Please contact 1-855-HD-GLACIER for further assistance.

16

Part Description Part Number

1 RP38046*

2 Shower arm RP38002*

3 Shower head RP38360*

4 O-ring RP60101

5 Cartridge RP20075

6 O-ring RP60091

7 Bonnet nut RP70437*

8 Sleeve RP80297*

9 Inverter RP64043

Shower ange

Part Description Part Number

14 Screw RP50012

10 Escutcheon RP80409*

11 Escutcheon screw RP50066*

12 Handle seat RP17005*

13 Handle RP13150*

15 Index RP10007*

16 Plug RP70365

17 Spout RP33004*

Service Parts

*Specify Finish

Many replacement cartridges, aerators, and drain

assemblies can be purchased at your local The

Home Depot store or online at HOMEDEPOT.COM

Faucet ID tags can be

found by removing the

handle

12

11

10

9

8

7

6

5

4

16

17

1

14

15

2

3

13

Questions, problems, missing parts?

Before returning to the store, call Glacier Bay Customer Service

8 a.m. - 7 p.m., EST, Monday - Friday

9 a.m. - 6 p.m., EST, Saturday

1-855-HD-GLACIER (1-855-434-5224)

HOMEDEPOT.COM

Retain this manual for future use.

GUÍA DE USO Y MANTENIMIENTO

GRIFO PARA BAÑERA Y DUCHA, DE UNA SOLA LLAVE

Apreciamos la conanza que has depositado en Glacier Bay al comprar este grifo para bañera y ducha. Nos esforzamos por

crear continuamente productos de calidad diseñados para mejorar tu hogar. Visítanos en Internet para ver nuestra línea

completa de productos disponibles para las necesidades de mejoras de tu hogar. ¡Gracias por elegir a Glacier Bay!

GRACIAS

¿Problemas, preguntas o piezas faltantes?

Antes de regresar a la tienda, llama al servicio al cliente de

Glacier Bay de lunes a viernes entre 8 a.m. y 7 p.m. y los

sábados entre 9 a.m. y 6 p.m.(hora estándar del Este)

1-855-HD-GLACIER (1-855-434-5224)

HOMEDEPOT.COM

Modelo núm.

HD873X-1001

HD873X-1004

HD873X-1027H2

SKU núm.

1003015371

1003002587

1003002782

Internet núm.

304367659

304367710

304367675

19

Tabla de contenido

Información importante .........................19

Garantía...................................................19

Pre-instalación .......................................20

.............20

Herramientas y herrajes necesarios ....20

Contenido del paquete .........................23

Instalación ..............................................24

Planicación de la instalación

Cuidado y limpieza ................................31

Piezas de repuesto ................................33

Solución de problemas ...........................32

Información importante

□ No instales este producto hasta que hayas leído y entendido las instrucciones de este manual. Si estás instalando

este producto para alguien, déjale este manual para que le sirva como referencia al dueño/usuario.

□ Los puertos de entrada están diseñados para 1/2 plg. Conexión de soldadura de tubería de COBRE o 1/2 plg.

Conexión de acoplamiento de rosca IPS. Para conexiones roscadas, envuelve los extremos roscados con cinta

selladora antes de conectar. Si vas a soldar las conexiones, algunas partes inamables deben quitarse antes

de la soldadura para evitar daños por calor. Si no estás seguro sobre cómo quitar estas partes, llámanos a

1-855-HD-Glacier.

□ Al soldar o cortar las líneas de suministro de agua, protege tus ojos con gafas de seguridad.

□ RUIDO Y GOLPE DE ARIETE EN SISTEMAS PEX: Debido a la exibilidad inherente del PEX, en comparación con

materiales de plomería metálicos, el ruido y golpe de ariete puede ocurrir de vez en cuando por sobrecargas

de presión. Es importante garantizar que la tubería no esté en contacto con paneles de pared, ductos de aire

propulsado u otros materiales de alta resonancia. La sujeción o anclaje son métodos para evitar estos ruidos.

NO USES tuberías PEX desde la válvula al caño de la bañera.

Garantía

GARANTÍA DE POR VIDA LIMITADA

Los productos de Glacier Bay están fabricados con normas y mano de obra de calidad superior y están respaldados

por nuestra garantía de por vida limitada. Los productos de Glacier Bay están garantizados al comprador consumidor

original de estar libres de defectos en materiales o mano de obra. Reemplazaremos LIBRE DE CARGOS cualquier

producto o pieza que se demuestre está defectuosa. Símplemente, devuelva el producto a cualquiera de las

ubicaciones de venta al detalle de The Home Depot o llame al 1-855-HD-GLACIER (1-855-434-5224) para recibir el

artículo de reemplazo. La prueba de compra (recibo de venta original) del comprador consumidor original debe estar

disponible para todos los reclamos de garantía de Glacier Bay.

Esta garantía excluye daños y fallos incidentales/consecuenciales debido al mal uso, abuso o desgaste normal por

el uso. Esta garantía excluye todos los usos industriales, comerciales y de negocios, a cuyos compradores por la

presente, se les ha ampliado una garantía limitada de cinco años a partir de la fecha de compra, con todos los otros

artículos de esta garantía que aplican excepto la duración de la garantía.

Algunos estados y provincias no permiten la exclusión o la limitación de los daños incidentales o consecuenciales,

por lo tanto, las limitaciones y exclusiones anteriores podrían no aplicar a usted. Esta garantía le otorga derechos

legales especícos y también puede tener otros derechos que varían de un estado a otro. Por favor, vaya a una

tienda o llame al 1-855-HD-GLACIER para más detalles.

Póngase en contacto con el Equipo de Servicio al Cliente llamando al 1-855-434-5224 o visite www.HomeDepot.com.

20

Pre-instalación

PLANIFICACIÓN DE LA INSTALACIÓN

Gafas de

seguridad

Cinta selladora

para roscas

Cortador de

tuberías

Llave de correa

Llave

ajustable

Cinta

métrica

Termómetro

Destornillador

Phillips

Destornillador de

cabeza plana

SILICONE

Sellador de

silicona

Antes de comenzar la instalación de este producto, asegúrate de que no falta ninguna pieza. Compara las piezas

con la lista de Contenido del paquete. Si falta alguna pieza o está dañada, no intentes instalar el producto.

Comunícate con el servicio al cliente para piezas de repuesto.

HERRAMIENTAS Y HERRAJES NECESARIOS

INSTALACIÓN AVANZADA: Consulta a un plomero o

profesional antes de instalar este producto.

Si estás cambiando tu válvula de plomería, consulta los cuatro métodos comunes que aparecen más abajo: COBRE,

IPS, PEX y CPVC. Quita la manija y el regulador de válvula preexistentes antes de reemplazar tu válvula. Cumple con

todos los códigos locales de construcción y plomería.

A. COBRE (Antes de soldar, quita el cartucho y las válvulas de cierre del cuerpo de la válvula)

Soplete Kit de alambre de

soldadura sin plomo

Serrucho

de punta

Cepillo de

alambre

Todas las instalaciones pueden variar en dependencia de cómo estaba instalado el grifo anterior. No se incluyen todos

los suministros para la instalación del grifo; sin embargo, están disponibles dondequiera que se vendan suministros de

plomería. Al elegir tus suministros de instalación, asegúrate de que son productos aprobados por UPC y/o CSA.

Linterna

HOMEDEPOT.COM

Para obtener asistencia, llama al 1-855-HD-GLACIER.

La page charge ...

Glacier Bay HD873X-1027H2 Guide d'installation

Ce manuel convient également à

Glacier Bay HD873X-1027H2 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents