Simplicity PRESSURE WASHER, BRIGGS & STRATTON [email protected] MODEL 020662-00 Manuel utilisateur
- Catégorie
- Nettoyeurs haute pression
- Taper
- Manuel utilisateur
Ce manuel convient également à
Not for
Reproduction
Manual No. 80017424 Rev C
BRIGGS & STRATTON CORPORATION
MILWAUKEE, WISCONSIN, U.S.A.
Pressure Washer
Operator’s Manual
This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA)
standard PW101-2010 (Testing and Rating Performance of Pressure Washers).
Not for
Reproduction
2 BRIGGSandSTRATTON.COM
Thank you for purchasing this quality-built Briggs & Stratton® pressure washer. We are pleased that you’ve
placed your confidence in the Briggs & Stratton brand. When operated and maintained according to the
instructions in this manual, your Briggs & Stratton pressure washer will provide many years of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with pressure
washers and how to avoid them. Because Briggs & Stratton does not necessarily know all the applications this
pressure washer could be used for, it is important that you read and understand these instructions thoroughly
before attempting to start or operate this equipment. Save these original instructions for future reference.
This pressure washer requires final assembly before use. Refer to the Assembly section of this manual for
instructions on final assembly procedures. Follow the instructions completely.
Where to Find Us
You never have to look far to find Briggs & Stratton support and service for your pressure washer. Consult your
Yellow Pages. There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality
service. You can also contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet
at BRIGGSandSTRATTON.COM.
Register Your Product
To ensure prompt and complete warranty coverage, register your product online at www.onlineproductregistration.com
Pressure Washer Engine
Model Number _____________________ Model Number ______________________
Revision __________________________ Type Number _______________________
Serial Number ______________________ Code Number _______________________
Date Purchased ___________________
Table of Contents
Operator Safety....................... 3
Assembly............................ 6
Features and Controls ................. 9
Operation........................... 10
Maintenance ........................ 14
Troubleshooting ..................... 20
Warranty ........................... 21
Product Specifications ................ 22
Common Service Parts ............... 22
Copyright © 2017. Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
Not for
Reproduction
3
Operator Safety
Equipment Description
Read this manual carefully and become
familiar with your pressure washer. Know
its applications, its limitations, and any
hazards involved.
This pressure washer operates at a maximum of 2,800
PSI (193 BAR) at a flow rate of up to 2.3 gallons
(8.7 l) per minute. This high quality residential system
features 10” (25.4 cm) wheels, axial cam pump with
stainless steel pistons, automatic cool down system,
half gallon cleaning tank system, nozzle extension with
quick connect fitting, a selector nozzle with 5 different
settings, a heavy duty 25 ft. (7.6 m) hose, and more.
Every effort has been made to ensure that information
in this manual is accurate and current. However, we
reserve the right to change, alter, or otherwise improve
the product and this document at any time without prior
notice.
The Emission Control System for this pressure washer
is warranted for standards set by the Environmental
Protection Agency and the California Air Resources
Board.
This spark ignition system complies with the Canadian
standard ICES-002.
Important Safety Information
Safety Symbols and Meanings
The safety alert symbol indicates a potential
personal injury hazard. A signal word (DANGER,
WARNING, or CAUTION) is used with the alert symbol
to designate a degree or level of hazard seriousness.
A safety symbol may be used to represent the type of
hazard. The signal word NOTICE is used to address
practices not related to personal injury.
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazard which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazard which, if not
avoided, could result in minor or moderate injury.
NOTICE address practices not related to personal
injury.
Fire
Explosion
Toxic Fumes
Hot Surface
Moving Parts
Electrical Shock
Slippery Surface
Fall
Kickback
Flying Objects
Fluid Injection
Operator’s Manual
Chemical Burn
Projectile
WARNING POISONOUS GAS HAZARD.
Engine exhaust contains carbon monoxide,
a poisonous gas that could kill you in
minutes. You CANNOT smell it, see it, or
taste it. Even if you do not smell exhaust fumes, you
could still be exposed to carbon monoxide gas.
Some chemicals or detergents could be harmful if
inhaled or ingested, resulting in death, serious
injury, nausea, fainting or poisoning.
• Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
• DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors
and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for hours,
even after this product has shut off.
• ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces.
If you start to feel sick, dizzy, or weak while using this
product, get to fresh air RIGHT AWAY. See a doctor. You
may have carbon monoxide poisoning.
• Use a respirator or mask whenever there is a chance that
vapors may be inhaled when using chemicals.
• Read all instructions with mask so you are certain the
mask will provide the necessary protection against
inhaling harmful vapors when using chemicals.
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting in
death or serious injury.
• DO NOT use caustic liquid with pressure washer.
• Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
Not for
Reproduction
4 BRIGGSandSTRATTON.COM
WARNING Fuel and its vapors are extremely
flammable and explosive which could
cause burns, fire or explosion
resulting in death or serious injury.
WHEN ADDING OR DRAINING FUEL
• Turn pressure washer engine OFF and let it cool at least
2 minutes before removing fuel cap. Loosen cap slowly to
relieve pressure in tank.
• Fill or drain fuel tank outdoors.
• DO NOT overfill tank. Allow space for fuel expansion.
• If fuel spills, wait until it evaporates before starting engine.
• Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
• Check fuel lines, tank, cap and fittings frequently for
cracks or leaks. Replace if necessary.
• DO NOT light a cigarette or smoke.
WHEN STARTING EQUIPMENT
• Ensure spark plug, muffler, fuel cap, and air cleaner are in
place.
• DO NOT crank engine with spark plug removed.
WHEN OPERATING EQUIPMENT
• DO NOT operate this product inside any building,
carport, porch, mobile equipment, marine applications, or
enclosure.
• DO NOT tip engine or equipment at angle which causes
fuel to spill.
• DO NOT spray flammable liquids.
WHEN TRANSPORTING, MOVING OR REPAIRING
EQUIPMENT
• Transport/move/repair with fuel tank EMPTY or with fuel
shutoff valve OFF (0).
• DO NOT tip engine or equipment at angle which causes
fuel to spill.
• Disconnect spark plug wire.
WHEN STORING FUEL OR EQUIPMENT IN THE FUEL
TANK
• Store away from furnaces, stoves, water heaters, clothes
dryers, or other appliances that have pilot light or other
ignition source because they could ignite fuel vapors.
WARNING Risk of electrocution.
Contact with power source could cause
electric shock or burn resulting in death or
serious injury.
• NEVER spray near power source.
WARNING Use of pressure washer could create
puddles and slippery surfaces
causing you to fall resulting in death
or serious injury.
Kickback from spray gun could cause you to fall
resulting in death or serious injury.
• Operate pressure washer from a stable surface.
• The cleaning area should have adequate slopes and
drainage to reduce the possibility of a fall due to slippery
surfaces.
• Be extremely careful if you must use the pressure washer
from a ladder, scaffolding, or any other similar location.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.
WARNING Starter cord kickback (rapid
retraction) will pull hand and arm toward
engine faster than you can let go which
could cause broken bones, fractures,
bruises, or sprains resulting in serious injury.
• NEVER pull starter cord without first relieving spray gun
pressure.
• When starting engine, pull cord slowly until resistance is
felt and then pull rapidly to avoid kickback.
• After each starting attempt, where engine fails to run,
always point spray gun in safe direction, press red button
and squeeze spray gun trigger to release high pressure.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage
fuel tank causing a fire, resulting in
death or serious injury.
Contact with muffler area could cause burns
resulting in serious injury.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 5 ft. (1.5 m) of clearance on all sides of
pressure washer including overhead.
• It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
defined in Section 4442, maintained in effective working
order. Other states or federal jurisdictions may have
similar laws.
Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
• Replacement parts must be the same and installed in the
same position as the original parts.
WARNING The engine exhaust from this
product contains chemicals known to the State of
California to cause cancer, birth defects, or other
reproductive harm.
WARNING This product contains lead and lead
compounds, known to the State of California to
cause birth defects or other reproductive harm.
Wash your hands after handling this product.
Not for
Reproduction
5
NOTICE High pressure spray could damage fragile
items including glass.
• DO NOT point spray gun at glass when using MAX (0°) setting
in selector nozzle.
• NEVER aim spray gun at plants.
NOTICE Improper treatment of pressure washer
could damage it and shorten its life.
• If you have questions about intended use, ask dealer or
contact qualified service center.
• NEVER operate units with broken or missing parts, or
without protective housing or covers.
• DO NOT by-pass any safety device on this machine.
• DO NOT tamper with governed speed.
• DO NOT operate pressure washer above rated pressure.
• DO NOT modify pressure washer in any way.
• Before starting pressure washer in cold weather, check all
parts of the equipment to be sure ice has not formed there.
• NEVER move machine by pulling on hoses. Use handle
provided on unit.
• This equipment is designed to be used with Briggs & Stratton
authorized parts ONLY. If equipment is used with parts that
DO NOT comply with minimum specifications, user assumes
all risks and liabilities.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• If cut by fluid, call physician immediately. DO NOT treat
as a simple cut.
• DO NOT allow CHILDREN to operate pressure washer.
• NEVER repair high pressure hose. Replace it.
• NEVER repair leaking connections with sealant of any
kind. Replace o-ring or seal.
• NEVER connect high pressure hose to nozzle extension.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
• NEVER aim spray gun at people, animals, or plants.
• DO NOT secure spray gun in open position.
• DO NOT leave spray gun unattended while machine is
running.
• NEVER use a spray gun which does not have a trigger
lock or trigger guard in place and in working order.
• Always be certain spray gun, nozzles and accessories
are correctly attached.
WARNING Unintentional sparking could cause
fire or electric shock resulting in death
or serious injury.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR
PRESSURE WASHER
• Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
• Use approved spark plug tester.
• DO NOT check for spark with spark plug removed.
WARNING Starter and other rotating parts
could entangle hands, hair, clothing, or
accessories resulting in serious injury.
• NEVER operate pressure washer without protective
housing or covers.
• DO NOT wear loose clothing, jewelry or anything that
could be caught in the starter or other rotating parts.
• Tie up long hair and remove jewelry.
CAUTION
Excessively high operating speeds
could result in minor injury.
Excessively low speeds impose a heavy load.
• DO NOT tamper with governor spring, links or other
parts to increase engine speed. Pressure washer
supplies correct rated pressure and flow when running at
governed speed.
• DO NOT modify pressure washer in any way.
WARNING Risk of eye or bodily injury.
Spray could splash back or propel
objects resulting in serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
• NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
• Always wear protective clothing such as a long-sleeved
shirt, long pants and close-toed shoes.
• NEVER operate pressure washer when barefoot or
wearing sandals or shorts.
Not for
Reproduction
6 BRIGGSandSTRATTON.COM
Assembly
Read entire operator’s manual before you
attempt to assemble or operate your new
pressure washer.
Your pressure washer requires some assembly and is
ready for use after it has been properly serviced with
the recommended oil and fuel.
If you have any problems with the assembly of your
pressure washer, please call the pressure washer
helpline at (800) 743-4115. If calling for assistance,
please have the model, revision, and serial number
from the identification label available.
Unpack Pressure Washer
1. Remove the parts bag, accessories, and inserts
included with pressure washer.
2. Open carton completely by cutting each corner
from top to bottom.
3. Ensure you have all included items prior to
assembly.
Items in the carton include:
• Main Unit with Cleaning Tank
• Handle
• High Pressure Hose
• Spray Gun
• Nozzle Extension with Quick Connect Fitting
• Plastic Accessory Tray
• Selector Nozzle
• Oil Pouch
• Parts Bag (which includes the following):
• Operator’s Manual
• Handle/Accessory Tray Fastening Hardware
Kit (which includes):
• Carriage Bolts (2)
• Plastic Knobs (2)
• Tree Clips (4)
To prepare your pressure washer for operation,
you will need to perform these tasks:
1. Attach handle and accessory tray to main unit.
2. Add oil to engine crankcase.
3. Add fuel to fuel tank.
4. Connect high pressure hose to spray gun and
pump.
5. Connect water supply to pump.
6. Attach nozzle extension to spray gun.
7. Attach quick connect selector nozzle to nozzle
extension.
Attach Handle and Accessory Tray
1. Place handle (A) onto handle supports connected
to main unit. Make sure holes in handle align with
holes on handle supports.
2. Insert handle carriage bolts (B) through holes from
inside of unit and attach a plastic knob (C) from
outside of unit. Tighten by hand.
NOTICE By loosening both knobs to the unthreaded
middle section of the attachment bolt, the upper handle
can fold forward to store flat atop the cold engine.
DO NOT fold the handle down while the engine is hot.
3. Place accessory tray (D) over holes (E) on handle
(viewing from front of unit). Push the tree clips (F) into
the holes until they sit flat against the accessory tray.
Add Engine Oil
1. Place pressure washer on a flat, level surface.
2. Clean area around oil fill and remove yellow oil fill
cap/dipstick.
3. Hold neck of supplied oil pouch and remove cap.
4. Slowly pour contents of oil pouch into oil fill
opening. Checking oil level frequently, fill to FULL
mark (top hole) on dipstick.
NOTICE Pause to permit oil to settle. Wipe dipstick
clean each time oil level is checked. DO NOT overfill.
NOTICE Improper treatment of pressure washer
could damage it and shorten its life.
• DO NOT attempt to crank or start the engine before it has
been properly serviced with the recommended oil. This
could result in an engine failure.
5. Replace oil fill cap/dipstick and fully tighten.
Full
Add
B
A
C
D
F
E
Not for
Reproduction
7
Add Fuel
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane/87 AKI (91 RON). For
high altitude use, see High Altitude.
• Gasoline with up to 10% ethanol (gasohol) is
acceptable.
NOTICE Use of unapproved fuels could damage
generator and voids warranty.
• DO NOT use unapproved gasoline such as E15 and E85.
• DO NOT mix oil in gasoline or modify engine to run on
alternate fuels.
To protect the fuel system from gum formation, mix in a
fuel stabilizer when adding fuel. See Storage. All fuel is
not the same. If you experience starting or performance
problems after using fuel, switch to a different fuel
provider or change brands. This engine is certified to
operate on gasoline. The emission control system for this
engine is EM (Engine Modifications).
1. Clean area around fuel fill cap, remove cap.
2. Slowly add regular unleaded fuel (A) to fuel tank (B).
Be careful not to overfill. To allow for fuel expansion,
do not fill above the bottom of the fuel tank neck.
3. Install fuel cap and let any spilled fuel evaporate
before starting engine.
High Altitude
At altitudes over 5,000 ft. (1524 m), a minimum
85 octane / 85 AKI (89 RON) gasoline is acceptable.
To remain emissions compliant, high altitude
adjustment is required. Operation without this
adjustment will cause decreased performance,
increased fuel consumption, and increased emissions.
See an Authorized Briggs & Stratton dealer for high
altitude adjustment information. Operation of the
engine at altitudes below 2,500 ft. (762 m) with the
high altitude kit is not recommended.
Lubricate O-Rings
Lubrication of o-rings is extremely important for
installation and operation. The use of a lubricant
(petroleum or synthetic grease) during assembly helps
seat o-rings properly and provides an improved seal. It
also helps protect the o-ring from damage by abrasion,
pinching or cutting and extends the life of the o-ring.
NOTICE ALWAYS apply a small amount of lubricant
on o-rings prior to assembling the garden hose to the
pump (C), high pressure hose (D), spray gun (E), and
nozzle extension (F).
Lubricate all connections following these instructions:
1. Inspect and clean connecting surfaces prior to
lubrication and assembly.
2. Use lubricants sparingly during assembly; a light
film is all that is required.
3. Use a small brush or cotton swab to apply grease
directly to o-rings where they are not accessible
(QC fitting, M22 fitting).
WARNING Fuel and its vapors are extremely
flammable and explosive which
could cause burns, fire or explosion
resulting in death or serious injury.
WHEN ADDING FUEL
• Turn pressure washer engine OFF and let it cool at least
2 minutes before removing fuel cap. Loosen cap slowly to
relieve pressure in tank.
• Fill fuel tank outdoors.
• DO NOT overfill tank. Allow space for fuel expansion.
• If fuel spills, wait until it evaporates before starting engine.
• Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
• Check fuel lines, tank, cap and fittings frequently for
cracks or leaks. Replace if necessary.
• DO NOT light a cigarette or smoke.
B
A
F
E
C
D
Not for
Reproduction
8 BRIGGSandSTRATTON.COM
Connect Hose and Water Supply to Pump
NOTICE DO NOT run the pump without the water
supply connected and turned on.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
NOTICE Remove and discard the shipping caps from
the pump’s high pressure outlet and water inlet before
attaching hoses.
1. Uncoil high pressure hose and attach one end of
hose to base of spray gun. Tighten by hand.
2. Attach other end of high pressure hose to high
pressure outlet on pump. Tighten by hand.
3. Run water through your garden hose for
30 seconds to clean out any debris.
NOTICE DO NOT siphon standing water for the water
supply. Use ONLY cold water (less than 100°F (38°C)).
4. Before connecting garden hose to water inlet,
inspect inlet screen (A). Clean screen if it contains
debris or have it replaced if damaged. DO NOT
run pressure washer if inlet screen is damaged.
NOTICE Using a One Way Valve (vacuum breaker
or check valve) at pump inlet could cause pump or
inlet connector damage.
• There MUST be at least 10 ft. (3 m) of unrestricted garden
hose between the pressure washer inlet and any device,
such as a vacuum breaker or check valve.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
5. Connect the garden hose (not to exceed
50 ft. (15 m) in length) to the water inlet. Tighten
by hand.
6. Turn ON the water, press red button (B) on the
gun and squeeze the trigger to purge the pump
system of air and impurities.
Checklist Before Starting Engine
Review the unit’s assembly to ensure you have
performed all of the following.
1. Be sure to read Operator Safety and Operation
before using pressure washer.
2. Make sure handle is in place and secure.
3. Check that oil has been added to proper level in
the engine crankcase.
4. Add proper fuel to fuel tank.
5. Check for properly tightened hose connections.
6. Check to make sure there are no kinks, cuts, or
damage to high pressure hose.
7. Provide a proper water supply at an adequate
flow.
A
B
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
• NEVER connect high pressure hose to nozzle extension.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• Always be certain spray gun, nozzles and accessories
are correctly attached.
WARNING Risk of eye injury.
Spray could splash back or propel objects
resulting in serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
• NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
Not for
Reproduction
9
A - Spray Gun — Controls the application of water
onto cleaning surface with trigger device. Includes
trigger lock.
B - Recoil Starter — Used for starting the engine
manually.
C - Oil Fill/Dipstick — Check and fill with oil here.
D - Engine Identification — Provides model, type
and code of engine. Please have these readily
available if calling for assistance.
E - High Pressure Outlet — Connection for high
pressure hose.
F - Water Inlet — Connection for garden hose.
G - Pump — Develops high pressure.
H - Automatic Cool Down System — Cycles water
through pump when water reaches 125°-155°F
(51°C-68°C). Warm water will discharge from pump
onto ground. This system prevents internal pump
damage.
J - Cleaning Tank — Use to hold up to 0.5 gallon
(1.9 l) of pressure washer detergent.
K - Identification Label — Provides model and serial
number of pressure washer. Please have these
readily available if calling for assistance.
L - Air Filter — Protects engine by filtering dust and
debris out of intake air.
M - Engine Rocker Switch — Push this switch to
ON (I) position before using recoil starter. Push
switch to OFF (0) position for shutting off engine.
N - Fuel Tank — Fill tank with regular unleaded fuel.
Always leave room for fuel expansion.
P - Warning/Operating Instructions Tag — Identifies
hazards and proper procedure to start/stop
pressure washer.
R - Nozzle Extension with Quick Connect — Allows
you to switch between selector nozzle and optional
nozzle accessories.
S - Selector Nozzle — Contains five different spray
pattern nozzles for various applications.
T - Accessory Tray — Provides convenient storage
for standard and optional accessories, such as
brushes, turbo wands, etc.
U - High Pressure Hose — Connect one end to water
pump and the other end to spray gun.
Features and Controls
Read this Operator’s Manual and safety rules before operating your pressure washer.
Compare the illustrations with your pressure washer, to familiarize yourself with the locations of various
controls and adjustments. Save this manual for future reference.
D
A
U
N
T
L
S
E
HG
F
B
M
R
P
K
,
J
C
Not for
Reproduction
10 BRIGGSandSTRATTON.COM
Operation
If you have any problems operating your pressure
washer, please call the pressure washer helpline at
(800) 743-4115.
Pressure Washer Location
Carbon Monoxide Poisoning
Risk of Fire Clearances
How to Start Your Pressure Washer
To start your pressure washer for the first time,
follow these instructions step-by-step. This starting
information also applies if you have let the pressure
washer sit idle for at least a day.
1. Place pressure washer near an outside water
source capable of supplying water at a flow rate
greater than 3.3 gallons (12.4 l) per minute and no
less than 20 PSI (1.3 BAR) at pressure washer end
of garden hose. DO NOT siphon supply water.
2. Check that high pressure hose is tightly connected
to spray gun and pump. See Assembly section.
3. Make sure unit is in a level position.
4. Connect garden hose to water inlet on pressure
washer pump.
NOTICE DO NOT run the pump without the water
supply connected and turned on.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
5. Turn ON water, point gun in a safe direction, press
red button and squeeze trigger to purge pump
system of air and impurities.
6. Attach nozzle extension to spray gun. Tighten by hand.
7. Pull back on collar of nozzle extension, insert
selector nozzle and release collar. Tug on selector
nozzle to make sure it is securely in place. See
How to Use Selector Nozzle.
8. Push engine rocker switch (A) to ON (I) position.
A
WARNING POISONOUS GAS HAZARD.
Engine exhaust contains carbon monoxide,
a poisonous gas that could kill you in
minutes. You CANNOT smell it, see it, or
taste it. Even if you do not smell exhaust fumes, you
could still be exposed to carbon monoxide gas.
• Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
• DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors
and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for hours,
even after this product has shut off.
• ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces.
If you start to feel sick, dizzy, or weak while using this
product, get to fresh air RIGHT AWAY. See a doctor. You
may have carbon monoxide poisoning.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage fuel
tank causing a fire, resulting in death or
serious injury.
• Keep at least 5 ft. (1.5 m) clearance on all sides of
pressure washer including overhead.
Not for
Reproduction
11
NOTICE This unit is equipped with a ReadyStart®
engine. A ReadyStart engine means there is no
priming or choking required.
9. When starting engine, position yourself as
recommended and grasp starter grip handle and
pull slowly until you feel some resistance. Then
pull rapidly to start engine.
10. Return starter grip handle slowly. DO NOT let
rope “snap back” against starter.
NOTICE Before starting the pressure washer, be sure
you are wearing safety goggles as described below.
WARNING Risk of eye injury.
Spray could splash back or propel objects
resulting in serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
• NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
WARNING Starter cord kickback (rapid
retraction) will pull hand and arm toward
engine faster than you can let go which
could cause broken bones, fractures,
bruises, or sprains resulting in serious injury.
• NEVER pull starter cord without first relieving spray gun
pressure.
• When starting engine, pull cord slowly until resistance is
felt and then pull rapidly to avoid kickback.
• After each starting attempt, where engine fails to run,
always point spray gun in safe direction, press red button
and squeeze spray gun trigger to release high pressure.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• DO NOT allow CHILDREN to operate pressure washer.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• NEVER aim spray gun at people, animals, or plants.
• DO NOT secure spray gun in open position.
• DO NOT leave spray gun unattended while machine is
running.
• NEVER use a spray gun which does not have a trigger
lock or trigger guard in place and in working order.
• Always be certain spray gun, nozzles and accessories
are correctly attached.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage
fuel tank causing a fire, resulting in
death or serious injury.
Contact with muffler area could cause burns
resulting in serious injury.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 5 ft. (1.5 m) of clearance on all sides of
pressure washer including overhead.
• It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
defined in Section 4442, maintained in effective working
order. Other states or federal jurisdictions may have
similar laws.
Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
• Replacement parts must be the same and installed in the
same position as the original parts.
Not for
Reproduction
12 BRIGGSandSTRATTON.COM
How to Stop Your Pressure Washer
1. Release spray gun trigger and let engine idle for
two minutes.
2. Push engine rocker switch to OFF (0) position.
3. ALWAYS point gun in a safe direction and press
red button and squeeze spray gun trigger to
release retained high water pressure.
How to Use Accessory Tray
The unit is equipped with an accessory tray with
places to store your spray gun, nozzle extension, high
pressure hose and selector nozzle.
1. Place nozzle extension in slots on left side of
accessory tray (viewing from rear of unit) and snap in.
2. Place spray gun through grooves on right side of
accessory tray.
3. Insert selector nozzle in hole provided on front of
accessory tray.
4. Wrap high pressure hose and hang on hook of
accessory tray.
How to Use Selector Nozzle
The selector nozzle allows you to switch between five
different spray pattern nozzles. Spray patterns can be
changed while pressure washer is running once spray
gun trigger safety lock is engaged. The spray patterns
vary as shown below.
Follow these instructions to change nozzle patterns:
1. Select desired spray pattern:
• MAX - For stubborn or hard to reach surface
such as second story surfaces, paint removal,
oil stains, rust removal or other stubborn
substances (tar, gum, grease, wax, etc.).
• GENERAL - For most all purpose cleaning
such as home siding, brick patios, wood decks,
driveways and sidewalks, garage floors, etc..
•
DELICATE - For gentle cleaning of cars/trucks,
boats, RV’s, patio furniture, lawn equipment, etc..
• FLUSH - For quick high flow clean up and
long reach cleaning of second story siding and
windows.
• SOAP - For general soap applications or to
launch soap to second story siding and windows.
cleaning of second story siding and windows.
2.
Push button on selector nozzle, nozzle dial will pop up.
3. Turn dial until desired spray pattern lines up with
button on selector nozzle.
4. Push dial in until it locks into place.
Usage Tips
• For most effective cleaning, keep selector nozzle
from 8 to 24 inches (20 to 61 cm) away from
cleaning surface.
• If you get selector nozzle too close, especially
using a high pressure spray pattern, you may
damage surface being cleaned.
• Do Not get closer than 6 inches (15 cm) when
cleaning tires.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
2800 PSI
2.1 GPM
2600 PSI
2.2 GPM
2400 PSI
2.3 GPM
WARNING
The high pressure stream of water that
this equipment produces could cut through
skin and its underlying tissues, resulting in
serious injury and possible amputation.
• NEVER change spray patterns without the trigger locked
on the spray gun.
• DO NOT twist selector nozzle while spraying.
Not for
Reproduction
13
Applying Detergent
To apply detergent, follow these steps:
1. Review use of selector nozzle.
2. Prepare detergent solution as required by job.
3. Pour detergent into cleaning tank.
NOTICE The cleaning tank holds 0.5 gallon (1.9 l).
4. Make sure SOAP spray pattern nozzle is selected
on selector nozzle.
NOTICE
Detergent cannot be applied with the MAX,
GENERAL, DELICATE or FLUSH spray pattern nozzles.
5. Make sure garden hose is connected to water
inlet. Check that high pressure hose is connected
to spray gun and pump. Turn on water.
NOTICE You must attach all hoses before you start
the engine.
• Starting the engine without all the hoses connected and
without the water turned ON could damage the pump.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
6. Start engine following instructions How to Start
Your Pressure Washer.
7. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward,
using long, even, overlapping strokes.
8. Allow detergent to “soak in” for 3-5 minutes
before washing and rinsing. Reapply as needed
to prevent surface from drying. DO NOT allow
detergent to dry on (prevents streaking).
Pressure Washer Rinsing
For Rinsing:
1. Select and change to desired spray pattern nozzle on
selector nozzle. See How To Use Selector Nozzle.
2. Keep the spray gun a safe distance from the area
you plan to spray.
3. Apply a high pressure spray to a small area, then
check the surface for damage. If no damage is
found, it is okay to continue cleaning.
5. Start at the top of the area to be rinsed, working
down with same overlapping strokes as you used
for washing and applying detergent.
Automatic Cool Down System (Thermal Relief)
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the
spray gun, circulating water in the pump can reach
temperatures above 125º-155ºF (51°-68°C). The
system engages to cool the pump by discharging the
warm water onto the ground.
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting in
death or serious injury.
• DO NOT use caustic liquid with pressure washer.
• Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
WARNING Kickback from spray gun could
cause you to fall resulting in death or
serious injury.
• Operate pressure washer from a stable surface.
• Be extremely careful if you must use the pressure washer
from a ladder, scaffolding, or any other similar location.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.
Not for
Reproduction
14 BRIGGSandSTRATTON.COM
Maintenance
Maintenance Schedule
Follow the hourly or calendar intervals, whichever
occurs first. More frequent service is required when
operating in adverse conditions noted below.
1
Clean if clogged. Replace if perforated or torn.
2
Service more often under dirty or dusty conditions.
General Recommendations
Regular maintenance will improve the performance
and extend the life of the pressure washer. See any
qualified dealer for service.
The pressure washer’s warranty does not cover
items that have been subjected to operator abuse or
negligence. To receive full value from the warranty,
the operator must maintain the pressure washer as
instructed in this manual, including proper storage as
detailed in Winter Storage and Long Term Storage.
NOTICE Should you have questions about replacing
components on your pressure washer, please call
(800) 743-4115 for assistance.
Some adjustments will need to be made periodically to
properly maintain your pressure washer.
All service and adjustments should be made at least
once each season. A new spark plug and clean air filter
assure proper fuel-air mixture and help your engine run
better and last longer. Follow the requirements in the
Maintenance Schedule chart above.
Pump Oil
DO NOT attempt any oil maintenance on this pump.
The pump is pre-lubricated and sealed from the
factory, requiring no additional maintenance for the life
of the pump.
Emissions Control
Maintenance, replacement, or repair of the
emissions control devices and systems may
be performed by any non-road engine repair
establishment or individual. However, to obtain
”no charge” emissions control service, the work must
be performed by a factory authorized dealer. See the
Emissions Warranty.
Before Each Use
1. Check engine oil level.
2. Clean debris.
3. Check water inlet screen for damage.
4. Check high pressure hose for leaks.
5. Check detergent tube/tank for damage.
6. Check spray gun and nozzle extension assembly
for leaks.
7. Rinse out garden hose to flush out debris.
Pressure Washer Maintenance
Clean Debris
Daily or before use, clean accumulated debris from
pressure washer. Keep linkage, spring and controls
clean. Keep area around and behind muffler free from
any combustible debris. Inspect cooling air slots and
openings on the pressure washer. These openings
must be kept clean and unobstructed.
pressure washer parts should be kept clean to reduce
the risk of overheating and ignition of accumulated
debris.
• Use a damp cloth to wipe exterior surfaces clean.
NOTICE Improper treatment of pressure washer
could damage it and shorten its life.
• DO NOT insert any objects through cooling slots.
• Use a soft bristle brush to loosen caked on dirt,
oil, etc.
• Use a vacuum cleaner to pick up loose dirt and
debris.
Check and Clean Inlet Screen
Examine the screen on the pump’s water inlet. Clean
it if the screen is clogged or replace it if screen is
damaged.
First 5 Hours
• Change engine oil
Every 8 Hours or Daily
• Check/clean water inlet screen
1
• Check high pressure hose
• Check detergent tube/tank
• Check spray gun and assembly for leaks
• Clean debris
• Check engine oil level
Every 50 Hours or Yearly
• Clean air cleaner
2
• Change engine oil
2
• Inspect muffler and spark arrester
Every 200 Hours
• Replace air cleaner
Yearly
• Replace spark plug
• Clean cooling system
2
Not for
Reproduction
15
Check High Pressure Hose
The high pressure hose can develop leaks from wear,
kinking, or abuse. Inspect the hose each time before
using it. Check for cuts, leaks, abrasions or bulging
of cover, damage or movement of couplings. If any of
these conditions exist, replace the hose immediately.
Check Detergent Tube/Tank
Examine the detergent tank and detergent tube and
clean if clogged. The tube should fit tightly on the
barbed fitting of the pump and tank. Examine the tube
for leaks or tears. Replace the tank or tube if either is
damaged.
Detergent Siphoning Check Ball
Occasionally check ball in detergent siphoning
system may become stuck from storage, dried soap,
or minerals in water. The check ball can be freed by
performing the following:
NOTICE Before performing this procedure, be sure
you are wearing safety goggles as described below.
1. Shut OFF engine and turn off water supply.
2. ALWAYS point spray gun in a safe direction,
press red button and squeeze spray gun trigger to
release retained high water pressure.
3. Remove detergent hose from barbed fitting on pump.
4. Using a firm, blunt object 7/64” in diameter or smaller,
by at least 1” long, such as an Allen wrench, slowly
insert the object into the barbed fitting until you meet
resistance. This resistance is the check ball.
5. Slowly push down until you feel the ball move
slightly, push no more than 1/8”. Slight pressure
may be required to free the ball.
6. Repeat steps 4 and 5 if necessary.
7. Reinstall detergent hose onto barb fitting.
8. Treat with PumpSaver as described in Protecting
the Pump during storage to prevent reoccurrence.
Check Spray Gun
Examine the hose connection to the spray gun and
make sure it is secure. Test the trigger by pressing the
red button and making sure the trigger “springs back”
into place when you release it. You should not be able
to press the trigger without pressing the red button.
Replace spray gun immediately if it fails any of these tests.
Selector Nozzle Maintenance
A pulsing sensation felt while squeezing the spray gun
trigger may be caused by excessive pump pressure.
The principal cause of excessive pump pressure is a
spray tip clogged or restricted with foreign materials,
such as dirt, etc. To correct the problem, immediately
clean the spray tip following these instructions:
1. Shut off engine and turn off water supply.
2. ALWAYS point spray gun in a safe direction,
press red button and squeeze spray gun trigger to
release retained high water pressure.
3.
Remove selector nozzle from end of nozzle extension.
4. Use a small paper clip to free any foreign material
clogging or restricting each nozzle (A) in the
selector nozzle.
5. Remove nozzle extension from spray gun.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
• NEVER repair high pressure hose. Replace it.
• Replacement hose rating MUST equal or exceed
maximum pressure rating of unit.
WARNING Risk of eye injury.
Spray could splash back or propel objects
resulting in serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
• NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
A
Not for
Reproduction
16 BRIGGSandSTRATTON.COM
6. Using a garden hose, remove additional debris
by back flushing water through nozzle extension.
Back flush between 30 to 60 seconds.
7. Reinstall selector nozzle into nozzle extension.
8. Reconnect nozzle extension to spray gun.
9. Make sure garden hose is connected to water
inlet. Check that high pressure hose is connected
to spray gun and pump. Turn on water.
10. Start engine following instructions How to Start
Your Pressure Washer.
11. Test pressure washer by operating in each spray
pattern.
O-Ring Maintenance
Purchase an O-Ring/Maintenance Kit, model 705001,
by contacting the nearest authorized service center.
It is not included with the pressure washer. This kit
includes replacement o-rings, rubber washer and water
inlet filter. Refer to the instruction sheet provided in the
kit to service your unit’s o-rings.
Engine Maintenance
Oil
Oil Recommendations
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF,
SG, SH, SJ or higher. DO NOT use special additives.
Outdoor temperatures determine the proper oil viscosity
for the engine. Use the chart to select the best viscosity
for the outdoor temperature range expected.
* Below 40°F (4°C) the use of SAE 30 will result in hard starting.
** Above 80°F (27°C) the use of 10W30 may cause
increased oil consumption. Check oil level more frequently.
Checking Oil Level
Oil level should be checked prior to each use or
at least every 8 hours of operation. Keep oil level
maintained.
1. Make sure pressure washer is on a level surface.
2. Remove oil dipstick and wipe dipstick with clean
cloth. Replace and tighten dipstick. Remove and
check oil level.
3. Verify oil is at FULL mark (top hole) on dipstick.
Replace and tighten dipstick.
Adding Engine Oil
1. Make sure pressure washer is on a level surface.
2. Check oil level as described in Checking Oil Level.
3. If needed, slowly pour oil into oil fill opening to
the FULL mark (top hole) on dipstick. DO NOT
overfill.
NOTICE Overfilling with oil could cause the engine
to not start, or hard starting.
• DO NOT overfill.
• If over the FULL mark on dipstick, drain oil to reduce oil
level to FULL mark on dipstick.
4. Replace and tighten dipstick.
WARNING Unintentional sparking could cause
fire or electric shock resulting in death
or serious injury.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR
PRESSURE WASHER
• Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
• Use approved spark plug tester.
• DO NOT check for spark with spark plug removed.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
• NEVER repair leaking connections with sealant of any
kind. Replace o-ring or seal.
Full
Add
Not for
Reproduction
17
Changing Engine Oil
If you are using your pressure washer under extremely
dirty or dusty conditions, or in extremely hot weather,
change the oil more often.
KEEP OUT OF REACH OF CHILDREN.
DON’T POLLUTE. CONSERVE
RESOURCES. RETURN USED OIL TO
COLLECTION CENTERS.
Change oil while engine is still warm from
running, as follows:
1. Drain fuel tank by running pressure washer until
fuel tank is empty.
2. Disconnect spark plug wire and keep it away from
spark plug.
3. Clean area around oil fill, remove oil fill cap/
dipstick. Wipe dipstick clean.
4. Tip your pressure washer to drain oil from oil fill
into a suitable container making sure you tip your
unit away from spark plug. When crankcase is
empty, return pressure washer to upright position.
5. Slowly pour recommended oil about 20 oz.
(0.6 liters) into oil fill opening. Pause to permit oil
to settle. Fill to FULL mark (top hole) on dipstick.
6. Wipe dipstick clean each time oil level is checked.
DO NOT overfill.
7. Replace and tighten dipstick.
8. Wipe up any remaining oil.
9. Reconnect spark plug wire to spark plug.
Service Air Cleaner
Your engine will not run properly and may be damaged
if you run it with a dirty air cleaner. Service more often
if operating under dirty or dusty conditions.
To service the air cleaner, follow these steps:
1. Pull the latch (A) and open cover (B).
2. Carefully remove air cleaner to prevent debris
from falling into carburetor.
3. Wash foam air cleaner (C) in liquid detergent and
water. Squeeze dry in a clean cloth.
4. SATURATE foam air cleaner in engine oil and
squeeze in a clean cloth to remove excess oil.
5. Reinstall clean or new foam air cleaner in base (D).
6. Close the cover and resecure the latch.
Service Spark Plug
Changing the spark plug will help your engine to start
easier and run better.
1. Clean area around spark plug.
2. Remove and inspect spark plug.
3. Replace spark plug if electrodes are pitted,
burned or porcelain is cracked. Use the
recommended replacement plug. See
Specifications.
4. Check electrode gap with wire feeler gauge and
reset spark plug gap to recommended gap if
necessary (see Specifications).
5. Install spark plug and tighten firmly.
Inspect Muffler and Spark Arrester
Inspect the muffler for cracks, corrosion, or other
damage. Remove the spark arrester, if equipped, and
inspect for damage or carbon blockage. If replacement
parts are required, make sure to use only original
equipment replacement parts.
CAUTION Avoid prolonged or repeated skin
contact with used motor oil.
• Used motor oil has been shown to cause skin cancer in
certain laboratory animals.
• Thoroughly wash exposed areas with soap and water.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage
fuel tank causing a fire, resulting in
death or serious injury.
Contact with muffler area could cause burns
resulting in serious injury.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 5 ft. (1.5 m) of clearance on all sides of
pressure washer including overhead.
• It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
defined in Section 4442, maintained in effective working
order. Other states or federal jurisdictions may have
similar laws.
Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
• Replacement parts must be the same and installed in the
same position as the original parts.
C
B
D
A
Not for
Reproduction
18 BRIGGSandSTRATTON.COM
Air Cooling System
Over time debris may accumulate in cylinder cooling
fins and cannot be observed without partial engine
disassembly. For this reason, we recommend you have
a qualified service dealer clean the cooling system per
recommended intervals (see Maintenance Schedule in
beginning of Maintenance section). Equally important
is to keep top of engine free from debris. See Clean
Debris.
Carburetor Adjustment
The carburetor on this engine is low emission. It is
equipped with a non-adjustable idle mixture valve.
Top speed has been set at the factory. If adjustment is
required, see an authorized service dealer.
After Each Use
Water should not remain in the unit for long periods
of time. Sediments or minerals can deposit on pump
parts and freeze pump action. Follow these procedures
after every use:
1. Flush detergent from pump by running pressure
washer for one to two minutes with a high
pressure spray pattern.
2. Shut OFF engine, turn off water supply, point gun
in a safe direction, press red button and squeeze
trigger to relieve trapped pressure, and let engine
cool.
3. Disconnect hose from spray gun and high
pressure outlet on pump. Drain water from hose,
gun, and nozzle extension. Use a rag to wipe off
the hose.
4. Place the spray gun, nozzle extension, and
selector nozzle in the accessory tray. Hang high
pressure hose on hook of accessory tray.
5. Empty pump of all pumped liquids by pulling recoil
handle about six times. This should remove most
liquid in pump.
6. Store unit in a clean, dry area.
7. If storing for more than 30 days, see Long Term
Storage on next page.
CAUTION
Excessively high operating speeds
could result in minor injury.
Excessively low speeds impose a heavy load.
• DO NOT tamper with governor spring, links or other
parts to increase engine speed. Pressure washer
supplies correct rated pressure and flow when running at
governed speed.
• DO NOT modify pressure washer in any way.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
WARNING Fuel and its vapors are extremely
flammable and explosive which could
cause burns, fire or explosion resulting
in death or serious injury.
STORING FUEL OR EQUIPMENT WITH FUEL IN TANK
• Store away from furnaces, stoves, water heaters, clothes
dryers, or other appliances that have pilot light or other
ignition source because they could ignite fuel vapors.
Not for
Reproduction
19
Winter Storage
NOTICE You must protect your unit from freezing
temperatures.
• Failure to do so will permanently damage your pump and
render your unit inoperable.
• Freeze damage is not covered under warranty.
To protect the unit from freezing temperatures:
1. Empty detergent tank as follows:
a. Place suitable container under barbed fitting
on detergent tank and and remove detergent
tube. Remove the tanks cover, tip pressure
washer forward slightly and empty tank
contents into container.
b. Reconnect hose to barbed fitting on tank.
c. Add 1 pint (0.5 liter) of clean fresh water to
detergent tank and close tanks cover.
2. Flush detergent tank by running pressure washer
with soap spray pattern. Flush until tank is empty.
3. Follow steps 2-5 in the previous section After
Each Use.
4. Use pump saver, Model 6039, to treat pump. This
minimizes freeze damage and lubricates pistons
and seals.
5. If pump saver is not available, connect a 3 ft. (1 m)
section of garden hose to water inlet adapter.
Pour RV-antifreeze (antifreeze without alcohol)
into hose. Pull recoil handle twice. Disconnect
3 ft. (1 m) hose.
6. Store unit in a clean, dry area.
Long Term Storage
If you do not plan to use the pressure washer for more
than 30 days, you must prepare the engine and pump
for long term storage.
Protect Fuel System
Fuel Additive:
Fuel can become stale when stored over 30 days. Stale
fuel causes acid and gum deposits to form in the fuel
system or on essential carburetor parts. To keep fuel
fresh, use Briggs & Stratton® Advanced Formula
Fuel Treatment & Stabilizer, available wherever
Briggs & Stratton genuine service parts are sold.
There is no need to drain gasoline from the engine
if a fuel stabilizer is added according to instructions.
Run the engine for 2 minutes to circulate the stabilizer
throughout the fuel system before storage.
If gasoline in the engine has not been treated with a
fuel stabilizer, it must be drained into an approved
container. Run the engine until it stops from lack
of fuel. The use of a fuel stabilizer in the storage
container is recommended to maintain freshness.
Change Oil
While engine is still warm, drain oil from crankcase.
Refill with recommended grade. See Changing Engine
Oil in Engine Maintenance.
Protecting the Pump
To protect the pump from damage caused by mineral
deposits or freezing, use PumpSaver, Model 6039,
to treat pump. This prevents freeze damage and
lubricates pistons and seals.
NOTICE PumpSaver is available as an optional
accessory. It is not included with the pressure washer.
Contact the nearest authorized service center to
purchase PumpSaver.
NOTICE You must protect your unit from freezing
temperatures.
• Failure to do so will permanently damage your pump and
render your unit inoperable.
• Freeze damage is not covered under warranty.
To use PumpSaver, make sure the pressure washer is
turned off and disconnected from supply water. Read
and follow all instructions and warnings given on the
PumpSaver container.
Other Storage Tips
1. DO NOT store fuel from one season to another
unless it has been treated as described in Protect
Fuel System.
2. Replace fuel container if it starts to rust. Rust and/
or dirt in fuel can cause problems if it’s used with
this unit.
3. Cover unit with a suitable protective cover that
does not retain moisture.
4. Store unit in a clean and dry area.
WARNING Storage covers could cause a fire
resulting in death or serious injury.
• DO NOT place a storage cover over a hot pressure washer.
• Let equipment cool for a sufficient time before placing the
cover on the equipment.
Not for
Reproduction
20 BRIGGSandSTRATTON.COM
Troubleshooting
Problem Cause Correction
Pump has following problems:
failure to produce pressure,
erratic pressure, chattering, loss
of pressure, low water volume.
1. Low pressure spray pattern
nozzle is selected.
2. Water inlet is blocked.
3. Inadequate water supply.
4. Inlet hose is kinked or leaking.
5. Clogged inlet hose screen.
6. Water supply is over 100°F
(38°C).
7. High pressure hose is blocked
or leaks.
8. Spray gun leaks.
9. Selector nozzle is obstructed.
1. Select high pressure spray
pattern nozzle on selector
nozzle.
2. Clear inlet.
3. Provide adequate water flow.
4. Straighten inlet hose, patch
leak.
5. Check and clean inlet hose
screen.
6. Provide cooler water supply.
7. Clear blocks in outlet hose.
8. Replace spray gun.
9. Clean selector nozzle.
Detergent fails to mix with spray.
1. Detergent tube is clogged or
cracked.
2. High pressure spray pattern
nozzle is selected.
3. Check ball stuck in detergent
siphoning system.
1. Clean or replace detergent tube.
2. Select soap spray pattern
nozzle on selector nozzle.
3. Unstick check ball as described
in Detergent Siphoning Check
Ball.
Engine will not start; starts and
runs rough or shuts down during
operation.
1. Engine rocker switch set to
OFF (0) position.
2. Low oil level.
3. Dirty air cleaner.
4. Out of fuel.
5. Stale fuel.
6. Spark plug wire not connected
to spark plug.
7. Bad spark plug.
8. Water in fuel.
1. Set engine rocker switch to
ON (I) position.
2. Fill crankcase to proper level.
3. Clean or replace air cleaner.
4. Fill fuel tank.
5. Drain fuel tank; fill with fresh
fuel.
6. Connect wire to spark plug.
7. Replace spark plug.
8. Drain fuel tank; fill with fresh
fuel.
Engine lacks power. Dirty air cleaner. Clean or replace air cleaner.
For all other troubleshooting problems, contact a Briggs & Stratton authorized service dealer.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
Simplicity PRESSURE WASHER, BRIGGS & STRATTON [email protected] MODEL 020662-00 Manuel utilisateur
- Catégorie
- Nettoyeurs haute pression
- Taper
- Manuel utilisateur
- Ce manuel convient également à