Bosch SPE53U56UC Manuel utilisateur

Dishwasher

en Operating instructions

Guide d’Utilisation fr

Lave-Vaisselle

9000981753 (9501)

Dear Valued Customer,

Welcome and congratulations on your new Bosch® dishwasher purchase! Our German

engineers work tirelessly to craft machines with virtually silent operation, resource-sav-

ing efficiency, and optimum quality. We know you’ll be pleased.

For other premium Bosch® appliances, visit us online at:

www.bosch-home.com/us (USA)

or

www.bosch-appliances.ca (Canada)

While there, don’t forget to register your new dishwasher by clicking on the Support

tab or filling out the product registration card enclosed with your new unit.

If you have any questions or comments, please contact us at: 1-800-944-2904

or write us at:

http://www.bosch-home.com/us/customer-support/contact-us.html

Table of Contents

Important Safety Instructions....................................................................2-3

Dishwasher Components............................................................................4-5

Dishwasher Setup......................................................................................6-8

Dishware Materials.......................................................................................9

Loading the Dishwasher.........................................................................10-11

Rack Features.............................................................................................12

Dishwasher Cycles and Options..................................................................13

Wash Cycle Information..............................................................................13

Operating the Dishwasher......................................................................14-15

Care and Maintenance............................................................................16-17

Troubleshooting Guide...........................................................................18-20

Customer Service.......................................................................................21

Statement of Limited Product Warranty .....................................................22

2

IMPORTANT SAFETY INSTRUCTIONS:

Please READ and SAVE this information

WARNING

Misuse of the dishwasher can result in serious injury or death. Do not use the dishwasher in

any way not covered in this manual or for any purpose other than those explained in the fol-

lowing pages.

Severe product damage and/or injury could result from the use of unqualified service techni-

cians or non-original replacement parts. All repairs must be performed by a qualified service

technician using only original equipment factory replacement parts.

Electrical shock or fire could result if the electrical supply for the dishwasher covered in this

manual is incorrectly installed or if the dishwasher has been improperly grounded. Do not use

the dishwasher covered in this manual unless you are certain the electrical supply has been

correctly installed and the dishwasher has been properly grounded.

Never use harsh chemicals to clean your dishwasher. Some chloride-containing products can

damage your dishwasher and may present health hazards!

NOTICE

Never use steam cleaning products to clean your dishwasher. The manufacturer will not be

responsible for the possible damages or consequences.

It is highly recommended for the end user to become familiar with the procedure to shut off

the incoming water supply and the procedure to shut off the incoming power supply. See the

Installation Instructions or contact your installer for more information.

To avoid possible dishwasher damage, do not use harsh chemicals, abrasive cleaners, scour-

ing pads (metal or plastic), or abrasive cloths/paper towels to clean your dishwasher’s exte-

rior door panel. Your dishwasher's exterior door panel can be damaged by doing so.

NSF/ANSI 184 Certified residential dishwashers are not intended for licensed food establish-

ments.

3

WARNING: To reduce the risk of fire, electrical

shock, or serious injury, observe the following:

1 This dishwasher is provided with Installation Instructions and this Use and Care Manual.

Read and understand all instructions before using the dishwasher.

2 This appliance must be grounded to a metal, permanent wiring system, or an equipment

grounding conductor must be run with the circuit conductors and connected to the equip-

ment grounding terminal or lead on the dishwasher. See the Installation Instructions

included with this dishwasher for more information on electrical requirements.

3 Use this dishwasher only for its intended function, which is the washing of household dish-

ware and kitchenware rated as dishwasher safe.

4 Use only detergents or rinsing agents recommended for use in a dishwasher, and keep

them out of the reach of children.

5 When loading items to be washed:

• Locate sharp items so they are not likely to damage the door seal.

• Load knives and other sharp utensils with their HANDLES UP to reduce the risk of

cut-type injuries.

• Do not wash plastic items unless they are marked “dishwasher safe” or the

equivalent. For plastic items not so marked, check the manufacturer’s recom-

mendations.

• Do not operate your dishwasher unless all enclosure panels are in place.

• Do not tamper with or override controls and interlocks.

6 Do not abuse, sit or stand on the door or dish racks of the dishwasher.

7 To reduce risk of injury, do not allow children to play in or on the dishwasher.

8 When children become old enough to operate the appliance, it is the responsibility of the

parents/legal guardians to ensure the children are instructed in safe practices by qualified

persons.

9 Under certain conditions, hydrogen gas may be produced in a hot water system that has

not been used for two weeks or more. Hydrogen gas is explosive. Before using a dish-

washer that is connected to a hot water system that has been unused for two weeks or

longer, turn on all hot water faucets and let the water flow from each for several minutes.

This will release any accumulated hydrogen gas. As the gas is explosive, do not smoke or

use an open flame during this time.

10 Remove the dishwasher door to the washing compartment when removing an old dish-

washer for service or discarding.

11 To avoid floor damage and possible mold growth, do not allow wet areas to remain around

or under the dishwasher.

12 Protect your dishwasher from the elements. Protect against freezing to avoid possible

damage to the fill valve. Damage caused by freezing is not covered by the warranty.

13

This appliance must be grounded. In the event of a malfunction or breakdown, grounding

will reduce the risk of electric shock by providing a path of least resistance for electric cur-

rent. This appliance is equipped with a cord having an equipment-grounding conductor.

• Improper connection of the equipment-grounding conductor can result in risk

of electric shock. Check with a qualified electrician or service representative if

you are in doubt whether the appliance is properly grounded.

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to

cause cancer, birth defects, or other reproductive harm.

4

Dishwasher Components

Wash Cycles Wash Cycle Options

Model Heavy Auto Normal Rinse Delay Delicate Sanitize

Extra

Shine®

SPE53U5xUC*

Additional Features Description

Rackmatic

* x can be any number

®

3 position adjustable upper rack.

The height of the upper rack can

be adjusted in 3 positions to create more space.

Time Remaining Indicator

Indicates the cycle time remaining.

46 dBA Sound Level

Quiet washing.

Delay Start

Start of a cycle can be delayed in 1-hour increments up to 24 hours.

Rinse Cycle

If you need to pre-rinse dishes to avoid odors, let the dishwasher do

the work for you. Place unrinsed dishes inside dishwasher and

select the “Rinse” cycle. Uses less water than hand rinsing and very

low energy. Note: Do not use detergent in this cycle.

Tab Tray / Upper Rack Han-

dle

Place detergent tabs inside the dispenser as normal. The tabs fall

into the tab tray and dissolve perfectly every time. Also serves as

an upper rack handle.

24/7 AquaStop

®

Leak Pro-

tection

If a leak has occurred, it shuts down operation and automati-

cally pumps out water to avoid contact with the ﬂoor.

2 Flip Tine Rows in lower

rack

Folds down to improve loading versatility.

Vase Holder

Positions tall vases securely.

Plastic Item Clips

Securely holds light-weight plastic accessories (cups, lids, etc.).

Low Salt Notiﬁcation Light

Illuminates to indicate Salt is low.

Low Rinse Aid Notiﬁcation

Light

Illuminates to indicate Rinse Aid is low.

Sanitized Notiﬁcation

Light

Illuminates to indicate sanitation requirements are met. Only avail-

able in Heavy, Auto, or Normal cycles.

Energy Efﬁcient 259 kWh

ENERGY STAR

®

qualiﬁed.

5

Upper rack spray arm

Vent hole

Detergent dispenser

Lower rack

Salt container

Lower rack spray arm

Upper rack

Rinse aid dispenser

Tablet Collecting Tray

Filter System

Silverware basket

Cup shelves

6

Dishwasher Setup

Water Softening System

Your dishwasher requires soft water to ensure proper washing results

and is equipped with an internal water softening system. However, if you

have a household water softening system, the internal system provided

is not needed.

For the water softening system to function properly, it will need to use

dishwasher water softening salt. The amount of salt dispensed can be

set from “H:00” to “H:07”. Salt is not used at H:00 (default factory set-

ting). The amount of salt required depends on the degree of hardness of

your tap water. See

Table 1

.

1

Turn the unit on using the

[ON/OFF]

button.

2 Hold down the “A” button (see Figure 1) and press [START] until

the display indicates “H:00”.

3 Release both buttons and press the “C” button to select the

desired setting.

4 Save the selected setting by pressing [START] .

Using the water hardness test strip

Figure 1

7

Figure 3

Figure 2

Salt

Only refill the salt container, using a funnel to pour, right before turning

on the unit to ensure that salt overflow is immediately washed away. This

prevents corrosion. See Figure 2.

1 Open the screw cap of the salt container.

2 Fill the container with water (only required when turning on the unit for

the first time).

3 Add dishwasher salt until the water is displaced and runs out.

4 Refill with salt as soon as the “Refill Salt

”

LED is lit.

Notice: Never fill the salt dispenser with detergent. It will destroy the

water softening system. To prevent corrosion, refill with salt and immedi-

ately begin any cycle.

Note: Do not use salt tablets or any salt other than dishwasher water softening salt.

For more information about ordering salt please contact Customer Service (1-800-944-2904).

Detergent

Use only detergent specifically designed for dishwashers. For best results, use fresh powdered dish-

washing detergent or detergent tabs

.

NOTICE

To avoid dishwasher damage, do not use hand dishwashing products in your dishwasher.

To avoid dishwasher damage, do not use too much detergent if your water is soft. Using too much

detergent with soft water may cause etching in glassware.

The dishwasher uses less water than most, therefore, less detergent is

required. With soft water, 1 tablespoon (15 ml) of detergent will clean

most loads. The detergent dispenser cup has lines that measure deter-

gent (Figure 3) to 1 tablespoon (15 ml) and 2 tablespoons (25 ml). 3

tablespoons (45 ml) of detergent will completely fill the detergent dis-

penser.

Note: If you do not know the hardness of your water supply, use 15 ml (1 tbsp)

of detergent. Increase the amount if necessary to the least amount required to

get your kitchenware clean.

Use the measuring lines in the detergent dispenser cup as a guide to

measure the amount of detergent recommended in Table 2.

Table 2- Recommended Detergent Amount

Wash Cycle

Hard Water/

Heavy Soil

Medium Water/

Medium Soil

Soft Water/

Little Soil

Heavy 3 tbsp (45 ml) 3 tbsp (45 ml) 1.75-3 tbsp (25-45 ml)

Auto 1.75-3 tbsp (25-45 ml) 1.75 tbsp (25 ml) 1-1.75 tbsp (15-25 ml)

Normal 1.75-3 tbsp (25-45 ml) 1.75 tbsp (25 ml) 1-1.75 tbsp (15-25 ml)

Rinse None None None

8

Figure 4

Figure 5

Figure 6

To Close:

• Place finger as shown in Figure 4.

• Slide door closed and press down firmly until it clicks.

To Open:

• To open the cover, push the button as shown in Figure 5.

• Cover will slide open.

Rinse Aid

To achieve proper drying, always use a liquid rinse aid, even if your detergent contains a rinse aid or

drying additive.

Note: The dishwasher indicates low rinse aid by turning on the “Refill Rinse Aid” LED in the display. If this light is

on, you need to refill the rinse aid dispenser by following the directions below.

Adding Rinse Aid

NOTICE

To avoid oversudsing or clogging, do not overfill the rinse aid dispenser. Wipe up any spills with a damp

cloth.

1 Add liquid rinse aid to the dispenser until it

is full (see Figure 6). Do not overfill.

2 Close the lid. Lid must be fully closed until it clicks in order to seal.

3

Wipe up any excess rinse aid that may have puddled when the dis-

penser reservoir is full.

The indicator light will go out a few moments after the dishwasher door is shut.

See page 15 for instructions on how to adjust the amount of rinse aid dispensed.

9

Dishware Materials

Note: Before using your dishwasher for the first time, check the information in this section. Some items

are not dishwasher safe and should be hand washed; others require special loading.

Recommended

Aluminum: Colored anodized aluminum may fade over time. Minerals in your water may cause

the aluminum to darken or spot. This can usually be removed with a soap-filled steel wool pad.

China, Crystal, Stoneware: Some hand-painted utensils may discolor, fade or spot. Hand wash

these utensils. Position fragile glassware so that it will not fall over or come in contact with

other utensils during the wash cycle.

Glass: Milk glasses may discolor or become yellow.

Non-stick Coatings: Apply a light coating of vegetable oil to non-stick surfaces after drying.

Plastics: Make sure the plasticware is dishwasher safe.

Stainless Steel, Sterling Silver and Silver Plates: Load these so they do not come in contact

with other metals.

Not Recommended

Acrylic: Crazing, small cracks throughout the acrylic, may occur.

Adhesive-Joined Pieces: Adhesives that join materials such as plastic, wood, bone, steel, cop-

per, tin, etc. may loosen.

Bone-Handled Utensils: Handles may separate.

Iron: Iron will rust. Hand wash and dry immediately.

Non-Dishware Items: Your dishwasher is intended for use in cleaning ONLY standard house-

hold dishware and kitchenware.

Pewter, Brass, Bronze: These items will tarnish. Hand wash and dry immediately.

Tin: Tin will stain. Hand wash and dry immediately.

Wood: Wooden bowls, wooden utensils and utensils with wooden handles can crack, warp

and lose their finish.

10

Upper Rack Lower Rack

Silverware Basket

Loading the Dishwasher

Do not pre-wash items with loosely attached soiling. Remove all food particles, bones, toothpicks and

excessive grease. Items having burned-on, baked-on or starchy soils may require some pretreatment. Refer

to the Dishware Materials section for more information about dishware suitability.

Load only dishwasher safe items into the dishwasher. Load dishes in the dishwasher racks so the insides

of bowls, pots and pans are facing the spray arms as shown. Avoid nesting and contact points between

dishes. Separate items of dissimilar metals. Use care to not block movement of the spray arms.

WARNING

The sharp points and edges of knives and other sharp utensils can cause serious injuries. Load knives and

other sharp utensils with edges down. Do not allow children to handle or play near knives and sharp uten-

sils.

NOTICE

To avoid dishwasher damage, do not load the dishwasher with paper products, plastic bags, packing mate-

rials or anything other than normal, dishwasher safe dishware and kitchenware.

11

Loading the Upper Rack

Ensure items do not protrude through the bottom of the racks and block the spray arms.

Note: When pushing the upper rack into the dishwasher, push it until it stops against the back of the tub so the

upper rack spray arm connects to the water supply at the back of the tub. Do not push racks in using the door.

Loading the Lower Rack

Place large items in the lower rack. Load pots, pans and bowls upside down. Do not block vent with tall

baking sheets. Load these items on the right side of the dishwasher.

Unloading the Dishwasher

When unloading the dishwasher, it is recommended to unload the lower rack first. Next, unload the sil-

verware basket followed by the upper rack. This prevents water from dripping down onto dishware.

Note: Dishes are more likely to chip when unloading before cooling.

Rack Features

Flip Tines

The upper and lower racks consist of tines that can be folded down

depending on what you may need to load in the rack. To fold down, grasp

the folding tine and release from notch. Push folding tine downward to

desired position as shown in Figure 7.

RackMatic®

The height of the upper rack can be adjusted in 3 positions to create more

space (see Figure 8).

1 Pull the empty upper rack out of the dishwasher until it stops.

2 To lower the rack, push the lever inward then upward.

3 To raise, hold the empty rack by the sides and lift up.

Cup Shelves

The shelf and the space underneath can be used for cups or for larger

serving utensils (see Figure 9).

Figure 7

Figure 8





Figure 9

12

Dishwasher Cycles and Options

Wash Cycles

Note: In order to save energy, it is recommended to set the “Auto Power Off” feature to “P:01” (see the “Auto

Power Off” section of this manual).

Heavy: Best for cleaning items with baked-on food or grease. These dishes would normally require soaking.

Auto: This is the most flexible cycle. With our most complex soil sensing capability, this cycle is perfect

for use with mixed loads of dishware with varying amounts of food soil.

Normal:

The Normal cycle is recommended for daily, regular, or typical use to completely wash a full load of

normally soiled dishes.

In order to obtain optimal performance with minimum energy consumption, it is recommended to disable all available

features except Auto Power Off as noted at the start of this section.

Note 1: See footnote for additional energy test setup instructions.

Rinse: Allows you to rinse food soil off of a partial load and hold them in the dishwasher until you are

ready to run a full load.

Wash Cycle Options

Delay Start: Allows you to delay the start time of your dishwasher in one hour increments up to 24 hours.

Delicate: Available only in the Heavy, Auto and Normal cycles. This option’s lower temperature will

reduce the risk of cloudy glasses.

Sanitize: The Sanitize feature is available only in the Heavy, Auto and Normal cycles. Select one of these

cycles, press the “Sanitize Option” button and then press Start to activate the Sanitation features. The

sanitize LED will light when sanitation requirements are met. The technical sanitation measures may also

improve the drying results.

Note: The dishwasher automatically defaults to Auto when turned off and back on. If you used the sanitize

option in your last cycle, the dishwasher will default to Auto with the Sanitize option selected when you turn it on.

Extra Shine®: Used in combination with a wash cycle (except Rinse), the Extra Shine® option raises the tem-

perature and extends the drying time to further enhance drying results and provides a brilliant shine.

Note 1: The Energy Guide label was based on the Normal or Regular soil sensing cycle as follows: The unit was tested without any

Rinse Aid (liquid) in the Rinse Aid chamber. A single dose of detergent was inserted into the Detergent Dispenser, with no detergent

being used in the prewash. The unit was not subjected to truncated testing per the definitions in the test procedure. We recommend that

dish loads such as the one in the energy certification test have the rack position set in the highest position.

13

Wash Cycle Information

The cycle times in this Use and Care Manual are based on normal soil loads and 120°F incoming water and

will vary based on your actual conditions.

Table 3 - Wash Cycle Information

Heavy Auto Normal Rinse

cycle time 110-125 min 105-129 min 130-135 min 9 min

water consumption 16.7-21.9 L

4.3 gal

11.1-20.0 L

2.9-5.3 gal

8.2-16.3 L

2.2-4.3 gal

4.0 L

1.0 gal

wash temperature 66-71°C

151-160°F

53-55°C

127-131°F

50-55°C

122-131°F

incoming

rinse temperature 72°C

162°F

70-72°C

158-162°F

65-69°C

149-156°F

incoming

Delicate

cycle time 85-95 min 85-95 min 102-105 min n/a

water consumption 16.7-21.9 L

4.4-5.8 gal

11.1-20.0 L

2.9-5.3 gal

8.2-16.3 L

2.2-4.3 gal

n/a

wash temperature 55°C (131°F) 50°C (122°F) 50°C (122°F) n/a

rinse temperature 60°C (140°F) 60°C (140°F) 60°C (140°F) n/a

Sanitize

cycle time 120-145 min 120-150 min 150-155 min n/a

water consumption 16.7-21.9 L

4.4-5.8 gal

11.1-20.0 L

2.9-5.3 gal

8.2-16.3 L

2.2-4.3 gal

n/a

wash temperature 66-71°C

151-160°F

53-55°C

127-131°F

50-55°C

122-131°F

n/a

rinse temperature 72°C (162°F) 72°C (162°F) 72°C (162°F) n/a

Extra Shine®

cycle time 120-145 min 120-150 min 150-155 min n/a

water consumption 16.7-21.9 L

4.4-5.8 gal

11.1-20.0 L

2.9-5.3 gal

8.2-16.3 L

2.2-4.3 gal

n/a

wash temperature 66-71°C

151-160°F

53-55°C

127-131°F

50-55°C

122-131°F

n/a

rinse temperature 72°C (162°F) 72°C (162°F) 72°C (162°F) n/a

Note: Only sanitizing cycles have been designed to meet the requirements of Section 6 of the NSF/ANSI Standard for

Residential Equipment for soil removal and sanitization efficacy. There is no intention, either directly or indirectly, to imply

that all cycles have passed sanitization performance tests

14

Operating the Dishwasher

NOTE: Buttons are sensitive and should be touched gently. Avoid any grease or food particles resting on

the buttons as they could activate the dishwasher. Wiping and cleaning can also activate the dishwasher.

For best results, use bare, clean hands when touching the buttons.

WARNING

To avoid risk of injury, always use caution when opening the door during or following a wash cycle as hot

water or steam may escape. Do not fully open the door until water noises have stopped and steam has

subsided.

Start the dishwasher

1

Press the [

On/Off]

button.

2 Select a cycle and desired options and press [Start].

Cancel a Cycle

1 Press and hold the [Start] button for approximately 3 seconds until the display reads “0:01”.

2 Wait about 1 minute while the dishwasher drains.

3 Press the [On/Off] button.

Interrupt a Cycle

1 Press the [On/Off] button to turn the unit off.

2 To resume the cycle, press the [On/Off] button.

WARNING

SPE53U5xUC*

A

B

C

* x can be any number

15

Setting the Amount of Rinse Aid

The amount of rinse aid dispensed can be set from “r:00” to “r:06”.

To change the setting:

1 Press the [On/Off] button.

2 Hold down the “A” button (see page 14) and press [Start] until the display indicates “H:00”.

3 Release both buttons.

4 Press the “A” button until the display shows “r:04”.

5 Press the “C” button to select the desired setting.

“r:00” = dispenser is OFF

“r:01” = lowest setting

“r:02” = low setting

“r:03” = medium setting

“r:04” = medium/high setting

“r:05” = high setting

“r:06” = highest setting

6 Press [Start] to save the setting.

Delay Start

You can delay the start of the cycle in one hour increments up to 24 hours.

To set delay start:

1 Press the [On/Off] button.

2 Press the [+] button until the display jumps to “h:01”.

3 Press the [+] or [-] button until the displayed time corresponds with your requirements.

h:01 = 1 hour delay

h:24 = 24 hour delay

4 Press [Start] to activate delay start.

To cancel delay start:

1 Press the [+] or [-] button until “h:00” is indicated on the digital display.

2 Press and hold [Start] for 3 seconds to cancel the cycle. You may now start a new cycle.

Auto Power Off

To save energy, the dishwasher is turned off 1 minute after the wash cycle ends. Auto Power Off can be

adjusted from P:00 to P:02.

To change the setting:

1 Press the [On/Off] button.

2 Hold down the “A” button (see page 14) and press [Start] until the display indicates “H:0x” (x can be

any number).

3 Release both buttons.

4 Press the “A” button until the display indicates “P:0x”.

5 Press the “C” button until the display corresponds with your requirements.

P:00 = dishwasher does not turn off automatically

P:01 = dishwasher turns off automatically after 1 minute

P:02 = dishwasher turns off automatically after 120 minutes (2 hours)

6 Press [Start] to save the setting.

Aquastop® Leak Protection

Our AquaStop® system contains leaks through a precisely engineered tub and sensor system that works

with our solid molded base. If a leak has occurred, it shuts down operation and automatically pumps out

water to avoid contact with the floor. It works 24/7 and can turn itself on.

16

Care and Maintenance

A regular inspection and maintenance of your machine will help to prevent faults. This saves time and

prevents future problems.

Overall condition of the machine

Never use a steam cleaner to clean your dishwasher. The manufacturer is not responsible for any con-

sequential damage.

Regularly wipe the front of the appliance with a damp cloth - water and a small amount of liquid soap is

adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the

surfaces.

Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or chlorine based cleaners.

Use a stainless steel polish to seal and protect the surface.

Clean the outer edges of the inside door panel regularly to remove debris that may collect from normal

loading. If spots begin to appear on the stainless steel, make sure the rinse agent is full and functioning

properly.

Use caution when removing parts for cleaning as some debris may be sharp.

Filters

The filter system consists of a coarse filter, a flat fine filter and a micro fil-

ter. The filters keep large foreign objects in the rinsing water away from the

pump. Foreign objects may occasionally block the filters.

Check the filters for residue by:

• Unscrew the filter cylinder as illustrated in Figures 10-11 and take out the

filter system.

• Remove any residue and clean filters under running water.

• Reinstall filter system in reverse sequence and ensure that the arrow

marks are facing each other after locking it into place.

Spray Arms

Check spray arms for grease and limescale

deposits.

If you find such deposits:

• Fill detergent dispenser with detergent and

start the appliance without utensils in the

cycle with the highest rinsing temperature

(see wash cycle information table).

• Clean the appliance with detergents/ appli-

ance cleaners which are particularly suitable

for use with dishwashers.

• Unscrew the spray arms and inspect as shown

in Figure 12.

Figure 10

Figure 11

Figure 12

WARNING

17

Drain Pump

Large food remnants in the rinsing water not retained by the filters may

block the drain pump. The rinsing water does not get pumped out and cov-

ers the filters.

In this case:

• Disconnect the appliance from the power supply.

• Remove the filters.

• Scoop out standing water - use a sponge if necessary.

• Using a spoon, pry off the pump cover (see Figures 13-14) until it clicks,

then grip the cover and pull upward until it resists and then pull forward.

• Check inner compartment and remove any foreign objects.

• Place cover in the original position, press down and engage.

• Reinstall filters.

NOTICE

Preparing your Dishwasher for Vacation

Before leaving for vacation during warmer weather, besides turning off the main valve, also turn off wa-

ter supply at the nearest point to the dishwasher. During colder weather, please follow the instructions

for winterizing your unit below.

NOTICE

Winterizing your Dishwasher

If your dishwasher will be unused for an extended period of time in a location that experiences freezing

temperatures (holiday home or through a vacation period), have your dishwasher winterized by a pro-

fessional servicer.

Figure 14

Figure 13







&OLFN

18

Troubleshooting Guide

Dishwashers may occasionally exhibit problems that are unrelated to a malfunction of the dishwasher itself. The

following information may help you with a dishwasher problem without involving a repair professional.

Problem Cause Action

Dishwasher

does not

start

1. Door may not be properly latched.

2. Unit may not be turned on.

3. Unit not reset or previous cycle not com-

pleted.

4. Delay start engaged.

5. Interruption of electrical power supply to

dishwasher or blown fuse.

6. The door may have been closed without

first selecting a cycle.

7. Water supply may not be turned on.

1. Shut the door completely.

2. Press the main power switch to turn unit

on.

3. To reset, refer to “Operating the Dish-

washer” in this manual.

4. To reset, refer to “Delay Start” section in

this manual.

5. Check circuit breaker.

6. Select a cycle and press start.

7. Check and turn on water supply.

Dishwasher

beeping (end

of cycle sig-

nal)

1. Default factory settings alert the customer

that the cycle is complete by beeping. This

feature can be deactivated if so desired.

2. Water connection is lost.

1. To adjust the volume or deactivate, refer

to the “Cycle Completion Signal” section in

this manual.

2. Check and turn on water supply.

Display does

not illumi-

nate or con-

sole lights

are not on

1. A fuse may have been blown or circuit

breaker tripped.

2. Door not closed or latched.

1. Check the fuse or circuit breaker box and

replace the fuse or reset the breaker if nec-

essary.

2. Ensure door is properly latched and com-

pletely closed.

Dishwasher

seems to run

a long time

1. Incoming water is not warm enough.

2. Cycle time can vary due to soil and water

conditions.

3. Rinse aid dispenser is empty.

4. Dishwasher connected to cold water sup-

ply.

Note: Refer to “Wash Cycle Information” section

in this manual for typical cycle lengths.

1. Before starting a cycle, run hot water

faucet at the sink closest to the dish-

washer.

2. Sensors in the dishwasher automatically

increase the cycle time to ensure a good

wash when heavy soil is detected.

3. Add rinse aid.

4. Verify dishwasher is connected to hot

water supply plumbing.

Dishes are

not getting

clean

enough

1. Spray arm movement obstructed.

2. Spray arm nozzles clogged.

3. Improper use of detergents.

4. Filters could be clogged.

5. Dishes are nested or loaded too close

together.

6. Selected wash cycle is not suitable for

food soil conditions.

1. Ensure that spray arm movement is not

blocked by hand rotating spray arms before

starting cycle.

2. Remove the spray arms and clean

according to the “Care and Maintenance”

section of the manual.

3. Increase or decrease detergent depend-

ing on the water hardness (refer to Table

1).

4. Clean the filters according to the “Care

and Maintenance” section of the manual.

5. Rearrange load such that water spray

can reach all items in the dishwasher - see

“Loading the Dishwasher” section of the

manual.

6. Refer to “Wash Cycle Information” sec-

tion of the manual.

La page est en cours de chargement...

Bosch SPE53U56UC Manuel utilisateur

Bosch SPE53U56UC Manuel utilisateur

dans d''autres langues

Documents connexes