GE JV347HWW Manuel utilisateur

Catégorie
Hottes
Taper
Manuel utilisateur
Range Hoods
ge.com
49-80424-1 02-07 JR
Safety Information . . . . . . . . 2, 3
Operating/Care and
Cleaning Instructions
Charcoal Filter . . . . . . . . . . . . . . .5
Grease Filter . . . . . . . . . . . . . . . .4
Hood Light . . . . . . . . . . . . . . . . .5
Hood Surfaces . . . . . . . . . . . . . . .5
Controls . . . . . . . . . . . . . . . . . . . .4
Installation Instructions . . .6–14
Consumer Support
Consumer Support . . .Back Cover
Warranty . . . . . . . . . . . . . . . . . . 15
JN327–Recirculation only
JV338*–Vent options only
JV347*–Vent & Recirculation
options
JV348*–Vent & Recirculation
options
JV367*–Vent & Recirculation
options
RN328–Recirculation only
Owner’s Manual and
Installation Instructions
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
You can find them on a label on the
back wall of the hood.
*
Operating Instructions Safety InstructionsConsumer Support Installation Instructions
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
READ AND SAVE THESE INSTRUCTIONS
SAFETY PRECAUTIONS
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING – TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
A. Use this unit only in the manner intended
by the manufacturer. If you have questions,
contact the manufacturer.
B. Before servicing or cleaning unit, switch power off
at service panel and lock the service disconnecting
means to prevent power from being switched on
accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag, to
the service panel.
C. Do not use this unit with any solid-state speed
control device.
D. If using a cord connection kit, use only with range
hood cord-connection kit JXHC1 that has been
investigated and found acceptable for use with
this model range hood.
E. This unit must be grounded.
CAUTION – FOR GENERAL VENTILATING USE
ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR
EXPLOSIVE MATERIALS AND VAPORS.
WARNING – TO REDUCE THE RISK OF
INJURY TO PERSONS IN THE EVENT OF A RANGE TOP
GREASE FIRE, OBSERVE THE FOLLOWING*:
A. SMOTHER FLAMES with a close-fitting lid,
cookie sheet or metal tray, then turn off the
burner. BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE
DEPARTMENT.
B. NEVER PICK UP A FLAMING PAN—
You may be burned.
C. DO NOT USE WATER, including wet
dishcloths or towels—a violent steam
explosion will result.
D. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher,
and you already know how to operate it.
2. The fire is small and contained in the area
where it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit.
* Based on “Kitchen Firesafety T
ips” published
by NFPA.
WARNING – TO REDUCE THE RISK OF
A RANGE TOP GREASE FIRE:
A. Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on low
or medium settings.
B. Always turn hood ON when cooking on high
heat or when flambeing food (i.e. Crepes Suzette,
Cherries Jubilee, Peppercorn Beef Flambé).
C. Clean ventilating fans frequently. Grease should
not be allowed to accumulate on fan or filter.
D. Use proper pan size. Always use cookware
appropriate for the size of the surface element.
WARNING –
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
A. Installation work and electrical wiring must be
done by qualified person(s) in accordance with
all applicable codes and standards, including
fire-rated construction.
B. Sufficient air is needed for proper combustion
and exhausting of gases through the flue
(chimney) of fuel burning equipment to prevent
back drafting. Follow the heating equipment
manufacturer’s guideline and safety standards
such as those published by the National Fire
Protection Association (NFPA), the American
Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE) and the
local code authorities.
C. When cutting or drilling into wall or ceiling, do
not damage electrical wiring and other hidden
utilities.
D. Ducted fans must always be vented to the
outdoors.
WARNING – TO REDUCE THE RISK OF FIRE,
USE ONLY METAL DUCTWORK.
Do not attempt to repair or replace any part of
your hood unless it is specifically recommended in
this guide. All other servicing should be referred to
a qualified technician.
2
Installation Instructions Consumer Support
Safety Instructions
Operating Instructions
LISEZ ET SUIVEZ ATTENTIVEMENT CES INSTRUCTIONS.
LISEZ ET CONSERVEZ CES INSTRUCTIONS
PRÉCAUTIONS EN MATIÈRE DE SÉCURITÉ
INSTRUCTIONS DE SÉCURITÉ IMPORTANTES.
LISEZ TOUTES LES INSTRUCTIONS AVANT D’UTILISER.
AVERTISSEMENT – POUR RÉDUIRE LE
RISQUE D’INCENDIE, DE SECOUSSE ÉLECTRIQUE OU DE
BLESSURE CORPORELLE, OBSERVEZ LES PRÉCAUTIONS
SUIVANTES :
A. N’utilisez cet appareil que de la manière prévue
par le fabricant. Si vous avez des questions, appelez
le fabricant.
B. Avant de réparer ou de nettoyer votre appareil,
débranchez le courant au niveau du panneau
de service et verrouillez les mécanismes de
débranchement de service pour éviter tout
branchement accidentel au courant. Si vous ne
pouvez pas verrouiller les mécanismes de
débranchement de service, attachez soigneusement
un avertissement bien visible, comme une étiquette,
au panneau de service.
C. N’utilisez jamais cet appareil avec un mécanisme
de réglage de la vitesse à semi-conducteurs.
D. Si vous utilisez l’ensemble de cordon de
raccordement, utilise seulement avec l’ensemble de
cordon de raccordement pour hotte JXHC1. Suite à
un examen technique, l’article JXHC1 s’est avéré
compatible avec ce modèle de hotte.
E. Cet appareil doit être bien mis à la terre.
ATTENTION – UNIQUEMENT À USAGE DE
VENTILATION GÉNÉRALE. N’UTILISEZ JAMAIS POUR
L’ÉCHAPPEMENT DE MATIÈRES ET DE VAPEURS
EXPLOSIVES.
AVERTISSEMENT – POUR RÉDUIRE LE
RISQUE DE BLESSURE CORPORELLE SI DE LA GRAISSE
PREND FEU SUR LA SURFACE DE CUISSON DE LA
CUISINIÈRE, SUIVEZ LES INSTRUCTIONS SUIVANTES* :
A. ÉTOUFFEZ LES FLAMMES avec un couvercle qui
convient, une tôle à biscuits ou un plateau en métal,
puis éteignez le brûleur. FAITES BIEN ATTENTION
DE NE PAS VOUS BRÛLER. Si les flammes ne
s’éteignent pas immédiatement, SORTEZ ET
APPELEZ LES POMPIERS.
B. NE DÉPLACEZ JAMAIS UNE CASSEROLLE QUI
FLAMBE – Vous pouvez vous brûler.
C. N’UTILISEZ JAMAIS D’EAU, en particulier de
serviette ou de chiffon mouillé – il se produira une
explosion violente de vapeur brûlante.
D. N’UTILISEZ UN EXTINCTEUR que si :
1. Vous avez un extincteur de classe ABC et vous
savez comment l’utiliser;
2. Le feu est réduit et confiné à l’endroit où il a
commencé;
3. Vous avez déjà appelé les pompiers;
4. Vous combattez les flammes en tournant le dos à
une sortie.
* Basé sur l’ouvrage intitulé «Kitchen Fire Safety Tips»
publié par la NFPA.
AVERTISSEMENT – POUR RÉDUIRE
LE RISQUE D’UN FEU DE GRAISSE SUR LA SURFACE
DE CUISSON DE LA CUISINIÈRE :
A. Ne laissez jamais sans surveillance les unités de
cuisson de surface à une température élevée. Le
bouillonnement occasionne des débordements
fumants et graisseux qui peuvent prendre feu.
Chauffez à feu doux les substances huileuses,
avec un réglage bas ou moyen.
B. ALLUMEZ toujours la hotte en cas de cuisson à
feu élevé ou lorsque vous faites flamber des aliments
(par exemple, crêpes Suzette, cerises jubilées, bœuf
au poivre flambé).
C. Nettoyez les mécanismes de ventilation
fréquemment. Il ne faut pas permettre une
accumulation de graisse sur le ventilateur ou
sur le filtre.
D. Utilisez une casserole de bonne taille. Utilisez
toujours un ustensile de cuisine qui convienne au
diamètre de l’élément de cuisson.
AVERTISSEMENT –
POUR RÉDUIRE LE
RISQUE D’INCENDIE, DE SECOUSSE ÉLECTRIQUE OU DE
BLESSURE CORPORELLE, OBSERVEZ LES PRÉCAUTIONS
SUIVANTES :
A. Vous devez faire exécuter tous les travaux
d’installation et de câblage électrique par une
personne qualifiée, conformément à tous les codes
et les normes en vigueur, en particulier ceux de
construction relatifs aux incendies.
B. Vous devez assez d’air pour avoir une bonne
combustion et permettre l’évacuation des gaz par le
conduit de cheminée du matériel de combustion du
carburant, afin d’éviter tout retour d’air. Suivez les
directives du fabricant de matériel de combustion et
les normes de sécurité comme celles publiées par la
National Fire Protection Association (NFPA),
l’American Society for Heating, Refrigeration and
Air Conditioning Engineers (ASHRAE), ainsi que les
modalités des codes locaux.
C. Si vous faites un trou ou une ouverture dans un mur
ou un plafond, n’endommagez pas les fils électriques
et les autres installations cachées de service public.
D. Vous devez toujours alimenter les ventilateurs dans
les conduits en air en provenance de l’extérieur.
AVERTISSEMENT – POUR RÉDUIRE
LE RISQUE D’INCENDIE, N’UTILISEZ QUE DES CONDUITS
EN MÉTAL.
N’essayez jamais de remplacer ou de réparer un
élément de votre hotte si le présent manuel ne le
recommande pas expressément. Tout autre entretien
doit être effectué par un technicien qualifié.
3
Operating Instructions Safety InstructionsConsumer Support Installation Instructions
Using the hood controls.
Throughout this manual, features and appearance may vary from your model.
FAN Control
Turn to HI, MED or LO as needed.
Continuous use of the fan system while cooking
helps keep the kitchen comfortable and less
humid. It also reduces cooking odors and soiling
moisture that create a frequent need for cleaning.
LIGHT Control
Turn to ON while cooking or to NITE for use as a
night light.
LIGHT Control
Press the pad at the top to turn the light ON.
FAN Control
Press the pad at the top to turn the fan on HI and
at the bottom to turn it on LO. The center position
is OFF.
Continuous use of the fan system while cooking
helps keep the kitchen comfortable and less
humid. It also reduces cooking odors and soiling
moisture that create a frequent need for cleaning.
Control Knobs (on some models)
Care and cleaning of the vent hood.
Be sure electrical power is off and all surfaces are cool before cleaning or servicing any part of the
vent hood.
The efficiency of your hood
depends on a clean filter.
Frequency of cleaning depends on
hood use and the type of cooking
you do. However, the grease filter
should be cleaned at least once a
month.
To remove:
Pull down on the center of the
front edge of the filter. The filter
will then slip out of the retaining
tabs on the back.
To replace:
Slip the back edge of the filter
into the retaining tabs and push
the front edge up until it snaps
into place.
To clean:
Soak and then agitate it in a hot
water and detergent solution.
Light brushing can be used to
remove embedded dirt. Rinse,
shake and let it dry before
replacing.
NEVER OPERATE THE HOOD
WITHOUT THE FILTER IN PLACE.
With careful handling, the metal
filter will last for years. If a new
replacement filter becomes
necessary, order the part from
your dealer. Order genuine GE
part number WB02X8391.
Reusable Metal Grease Filter—Ducted Installations Only
4
Switch Pad Controls (on some models)
Grease filter
LO HI
MED NITE
OFF
OFF
ON
LO
OFF
HI
OFF
ON
Installation Instructions
Consumer Support
Safety Instructions Operating Instructions
Do not use steel-wool pads or other
abrasive cleaners. They will scratch
the surface.
Clean grease-laden surfaces of the
hood frequently. To clean the hood
surface, use a hot, damp cloth with a
mild detergent suitable for painted
surfaces. About one tablespoon of
ammonia may be added to the
water. Use a clean, hot, damp
cloth to remove soap. Dry with
a dry, clean cloth.
NOTE: When cleaning, take care not
to come in contact with filters and
other non-enameled surfaces.
CAUTION: When cleaning the
hood surfaces, be certain that you
do not touch the light bulb with moist
hands or cloth. A warm or hot light
bulb may break if touched with a moist
surface. Always let the light bulb cool
completely before cleaning around it.
Painted Surfaces
(on some models)
CAUTION: Let the light bulb cool
completely before removing. A
warm or hot bulb may break if
touched with a moist cloth or hand.
Remove the bulb and replace it
with a type A15 light bulb with an
ordinary screw-base, not more than
60 watts.
To remove the light cover
(on some models):
Press the sides with two fingers
until the side prongs are released.
Lift the light cover and slide it
toward you in one motion.
To replace the light cover:
Insert the prong located at the
end of the cover into the top
opening.
Gently push the cover up and
press the sides to fit the side
prongs into the side openings.
Release and the cover will lock
in position.
Hood Light
The charcoal filter cannot be cleaned.
It must be replaced. Order filter no.
WB02X10700. Replacement filters
can be ordered from your GE supplier.
If the hood is not vented to the
outside, the air will be recirculated
through a disposable charcoal filter
that helps remove smoke and odors.
The charcoal filter should be
replaced after 6 to 12 months
(depending on hood usage).
To remove:
Pull down on the center of the front
edge of the filter. The filter will then
slip out of the retaining tabs on the
back.
To replace:
Slip the back edge of the filter into
the retaining tabs and push the
front edge up until it snaps into
place.
Charcoal Filter—Recirculating Installations Only
Replaceable charcoal filter
5
NOTE: DO NOT rinse, or put charcoal filters in
an automatic dishwasher.
Light cover
Do not use a steel-wool pad; it will
scratch the surface.
To clean the stainless steel
surface, use warm sudsy water or
a stainless steel cleaner or polish.
Always wipe the surface in the
direction of the grain. Follow the
cleaner instructions for cleaning
the stainless steel surface.
To inquire about purchasing
stainless steel appliance cleaner or
polish, or to find the location of a
dealer nearest you, please call our
toll-free number:
National Parts Center 800.626.2002
ge.com
Stainless Steel Surfaces
(on some models)
CAUTION: Use only a type A15 light bulb,
60 Watt maximum.
BEFORE YOU BEGIN
6
Installation Range Hood
Instructions
Read these instructions completely and carefully.
IMPORTANT – Save these
instructions for local inspector’s use.
IMPORTANT – Observe all
governing codes and ordinances.
Note to Installer – Be sure to leave these
instructions with the Consumer.
Note to Consumer – Keep these instructions
for future reference.
Skill level – Installation of this appliance requires
basic mechanical and electrical skills.
Completion time – 30 minutes–3 hours
Proper installation is the responsibility of the
installer.
Product failure due to improper installation is not
covered under the Warranty.
NOTE: Read the ductwork sections only if you do not
have existing ductwork. If you have existing ductwork,
skip to the “Damage” section and proceed.
The venting system must exhaust to the outside.
This hood can be vented vertically through upper
cabinets or horizontally through an outside wall.
Ductwork is not included.
Exhaust connection:
The hood exhaust has been designed to mate with
standard 3
1
4 x 10 rectangular ducting or 7 diameter
round ducting.
If a 6round duct is required, a rectangular-to-round
transition adaptor must be used*. Do not use less than
a 6diameter duct.
Maximum duct length:
For satisfactory air movement, the total duct length
of a 3
1
4 x 10 rectangular, 6or 7diameter round
duct should not exceed 65 equivalent feet. See the
WORKSHEET–CALCULATE TOTAL EQUIVALENT
DUCTWORK LENGTH section.
NOTE: It is important that ducting be installed using
the most direct route and with as few elbows as possible.
This ensures clear venting of exhaust and helps prevent
blockages. Also, make sure dampers swing freely and
nothing is blocking the ducts.
Elbows, transitions, wall and roofcaps, etc.,
present additional resistance to airflow and are
equivalent to a section of straight duct longer than their
actual physical size. When calculating the total duct
length, add the equivalent lengths of all transitions and
adaptors plus the length of all straight duct sections. The
charts on the following pages show you how to calculate
total equivalent ductwork length using the approximate
feet of equivalent length of some typical ducts.
* IMPORTANT: If a rectangular-to-
round transition adaptor is used, the
bottom corners of the damper will
have to be cut to fit, using the tin
snips, in order to allow free
movement of the damper.
Equivalent lengths of duct pieces
are based on actual tests and reflect
requirements for good venting
performance with any hood.
DUCTWORK REQUIREMENTS
WARNING – Before beginning the
installation, switch power off at service panel and lock
the service disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
FOR YOUR SAFETY:
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
An optional Power Cord Connection Kit, model
JXHC1, is available at extra cost from your GE
supplier for installation using a standard 3-prong,
grounded wall outlet. Follow the Installation
Instructions packed with the kit to connect
the power cord to the range hood.
OPTIONAL POWER CORD KIT JXHC1
7
DUCT EQUIVALENT NUMBER
PIECES LENGTH x USED = TOTAL
3
1
4x 10 1 Ft. x ( ) = Ft.
Rect.,
straight
7 Round, 1 Ft. x ( ) = Ft.
straight
6 Round, 1 Ft. x ( ) = Ft.
straight
3
1
4x 10 14 Ft. x ( ) = Ft.
Rect. 90°
elbow
3
1
4x 10 8 Ft. x ( ) = Ft.
Rect. 45°
elbow
3
1
4x 10 33 Ft. x ( ) = Ft.
Rect. 90°
flat elbow
3
1
4x 10 24 Ft. x ( ) = Ft.
Rect.
(18 ft. w/o
wall cap
damper)
x ( ) = Ft.
with
damper
3
1
4x 10 2 Ft. x ( ) = Ft.
Rect. to
6 round
transition
3
1
4x 10 4 Ft. x ( ) = Ft.
Rect. to
6 round
transition
90° elbow
6 Round, 25 Ft. x ( ) = Ft.
90° elbow
6 Round, 16 Ft. x ( ) = Ft.
45° elbow
Subtotal column 1 = Ft.
WORKSHEET—CALCULATE TOTAL EQUIVALENT DUCTWORK LENGTH
DUCT EQUIVALENT NUMBER
PIECES LENGTH x USED = TOTAL
6Round 53 Ft. x ( ) = Ft.
wall cap
(39 ft. w/o
with
damper)
x ( ) = Ft.
damper
6Round 72 Ft. x ( ) = Ft.
roof cap
6 Round 3 Ft. x ( ) = Ft.
to
3
1
4x 10
rect.
transition
6 Round 9 Ft. x ( ) = Ft.
to
3
1
4x 10
rect.
transition
90° elbow
7 Round, 14 Ft. x ( ) = Ft.
90° elbow
7 Round, 9 Ft. x ( ) = Ft.
45° elbow
7Round 28 Ft. x ( ) = Ft.
wall cap (
21 ft. w/o
with
damper)
x ( ) = Ft.
damper
7Round 39 Ft. x ( ) = Ft.
roof cap
7 Round 1 Ft. x ( ) = Ft.
to
3
1
4x 10
rect.
transition
7Round 5 Ft. x ( ) = Ft.
to
3
1
4
x 10
rect.
transition,
90° elbow
Subtotal column 2 = Ft.
Subtotal column 1 = Ft.
Total ductwork = Ft.
Installation Instructions
MAXIMUM DUCT LENGTH: For satisfactory air
movement, the total duct length of a 3
1
4 x 10
rectangular, 7 diameter round duct should
not exceed 65 equivalent feet.
PART QUANTITY
Grease Filter only (JV338) 1
Charcoal Filter only 1
(JN327 and RN328)
Grease Filter and Charcoal 2
Filter (JV347, JV348 and JV367)
Mounting Screws 4
(8 - 18 x 3/4 Phillips pan head)
Exhaust Adaptor 1
(for 3
1
4 x 10rect. venting)
Exhaust Adaptor Screw 1
(8 - 18 x 3/8 Phillips pan head
or hex head)
8
If the unit is damaged in shipment, return the unit to the
store in which it was bought for repair or replacement.
If the unit is damaged by the customer, repair or
replacement is the responsibility of the customer.
If the unit is damaged by the installer (if other than
the customer), repair or replacement must be made
by arrangement between customer and installer.
DAMAGE – SHIPMENT/INSTALLATION
PARTS INCLUDED
MOUNTING SPACE
NOTES:
This range hood is for installation over ranges or
cooktops up to 36wide.
If you are going to vent your range hood to the
outside, see the “Ducting Requirements” section
for exhaust duct preparation.
66or more
from the floor
to the top of
the hood
30or 36
30
min.
Bottom edge of
cabinet needs
to be 30or
more from
the cooking
surface
Flat blade and Phillips
screwdrivers
Pencil
Metal snips
(in some
applications)
Electric drill
Saw (saber or keyhole)
Duct tape
Pliers
Level
Caulking
Tape measure
TOOLS YOU WILL NEED
1/4pivoting
hex socket
Flashlight
Wire stripper
1/4Nutdriver
Installation Instructions
9
Outside top exhaust
(Vertical duct–3
1
4 x 10 Rectangular)
Outside rear exhaust
(Horizontal duct–3
1
4 x 10
Rectangular)
Outside top exhaust
(Vertical duct–7 Round)
A
C
B
Recirculating
(non-vented/ductless)
D
Installation Instructions
CHOOSE VENT OPTION
Determine the vent option that your installation will
require and that is available for your model from the
below choices.
1
IMPORTANT: If the hood is to be installed in a
recirculating, non-vented ductless manner, do not
knock out any vent openings in the hood. Only an
electrical access hole will be knocked out of the hood.
JV338
JV347
JV348
JV367
JV338
JV347
JV348
JV367
JV338
JV347
JV348
JV367
JN327
RN328
JV347
JV348
JV367
10
REMOVE EXHAUST ADAPTOR
If exhausting/venting using the 3
1
4x 10 rectangular
duct—optional for JV338, JV347, JV348 and JV367
models only:
Remove the exhaust adaptor from the inside of the
hood. Set it aside along with its mounting screws.
3
1
4x 10
rectangular
exhaust
adaptor
and screws
REMOVE FILTER
Remove the shipping tape holding the metal grease
filter in place. Pull down on the center of the front
edge of the filter. The filter will then slip out of the
retaining tabs on the back.
REVERSE THE BAFFLE FOR
DUCTED INSTALLATIONS ONLY
(JV347, JV348 and JV367 models)
If the hood is to be recirculated, skip to the next step.
Remove the baffle from the top of the hood. Re-install
the baffle so the short side marked “VENTED” is
visible. The long side of the baffle should be inside
the hood.
REMOVE WIRING COVER
Remove the wiring cover from inside the hood.
Set the cover and its mounting screw aside.
Wiring
cover
REMOVE WIRING KNOCKOUT
Remove either the top or the back wiring knockout as
needed and install an approved strain relief clamp.
Strain relief
clamp
2
3
4
5
6
Metal grease filter
Installation Instructions
Back knockout
Top knockout
“VENTED” is visible
Strain relief
clamp
REMOVE DUCT KNOCKOUT
If recirculating, non-vented ductless (JN327 and RN328,
and optional for JV347, JV348 and JV367 models only),
skip to Step 10 D and proceed.
Using a flat blade screwdriver, remove the appropriate
duct knockout from the top or back of the hood.
3
1
4x 10 Rectangular
vertical discharge.
Remove top rectangular
duct knockout only.
7Round vertical
discharge. Remove circular
duct knockout only.
3
1
4x 10 Rectangular
horizontal discharge. Remove
rear rectangular duct knockout only.
7
11
FOR 3
1
4 X 10 RECTANGULAR
DUCTED DISCHARGE
INSTALLATIONS ONLY:
Attach exhaust adaptor/damper over the appropriate
knockout opening (for vertical or horizontal,
depending on installation) with two exhaust adaptor
screws. Make sure damper pivot is nearest to top/back
edge of hood. Remove tape from damper flap.
Up to 1side-to-
side adjustment
Tape
Top/back edge
Exhaust adaptor/damper
(vertical discharge position)
Pivot
(depending on
installation)
FOR 7 ROUND VERTICAL
DUCTED DISCHARGE
INSTALLATIONS ONLY:
Bend up the duct alignment ears in preparation for
later attachment of the 7duct.
8
9
Installation Instructions
NOTE: The exhaust adaptor/damper can be installed
up to 1 inch on either side of the hood center to
accommodate off-center ductwork. In extreme off-
center installations, one end of the duct connector may
need to be trimmed to clear the electrical cable clamp.
Exhaust adaptor/damper
(horizontal discharge position)
Attachment ear tabs
FOR RECESSED-BOTTOM
CABINETS ONLY
10
Wood shims
(minimum thickness 3/8″)
If the cabinets have front, side or back trim, make
2 wood shims a minimum of 3/8 thick and cut to
fit the width of the inner recessed cabinet bottom.
Attach them to the cabinet bottom recess on both
sides. See Step 11 for marking locations.
12
D.
Recirculating (non-vented ductless–
JN327 and RN328, and optional on
JV347, JV348 and JV367 models only)
Use the hood as a template and mark the locations
on the cabinet for the electrical wiring and keyhole
screw slots.
Since the hood is to be recirculated (not to be vented
outside), do not cut out any vent openings in the wall
or cabinet bottom.
Installation Instructions
Wood shims
(recessed-bottom cabinets only–shims must be a
minimum of 3/8 thick and cut to fit the width
of the inner recessed cabinet bottom)
Cabinet front
Center line
Electrical access hole
(in wall)
Hood mounting screws (4)
Horizontal duct
access hole
Cabinet
bottom
13
3
4(30hood)
16
3
4(36hood)
1
1
4
1
2
3
3
4
5
1
4
5
1
4
7
3
4
13
3
4(30hood)
16
3
4(36hood)
C.
Outside rear exhaust
(Horizontal duct–3
1
4
x 10
Rectangular)
Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
RUN WIRES
Run the electrical wires through the wall or
cabinet according to National Electrical Code
and applicable local codes.
NOTE: DO NOT turn the power on until
installation is complete.
13
CUT HOLES
Cut holes at marked locations for duct and electrical
wiring. For the vertical duct, cut out 3/4 extra
toward the front of the cabinet so you can move the
duct freely when installing the hood. It may also ease
installation by cutting the hole 10
1
2instead of 10.
12
MARK HOLES
Select the vent option that your installation will
require and proceed to that section:
Hood mounting screws (4)
13
3
4(30hood)
16
3
4(36hood)
13
3
4
(30
hood)
16
3
4
(36
hood)
Cabinet front
Center
line
Electrical access hole
(in cabinet bottom)
Wood shims
(recessed-bottom cabinets
only–shims must be a
minimum of 3/8 thick
and cut to fit the width
of the inner recessed
cabinet bottom)
Vertical duct
access hole
9
5
8
1
3
8
1
1
4
7
3
4
3
3
4
1
2
A.
Outside top exhaust
(Vertical duct–3
1
4
x 10
Rectangular)
Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
B.Outside
top exhaust (Vertical duct–7 Round)
Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
Hood mounting screws (4)
13
3
4(30hood)
16
3
4(36hood)
13
3
4
(30
hood)
16
3
4
(36
hood
)
Cabinet front
Center
line
Electrical access
hole (in cabinet bottom)
Wood shims
(recessed-bottom cabinets
only–shims must be a minimum
of 3/8 thick and cut to fit the
width of the inner recessed
cabinet bottom)
Access
hole for 7
round duct
9
5
8
1
3
8
1
1
4
7
3
4
5
3
4
Cabinet
bottom
8 DIA.
HOLE
Cabinet Bottom
11
5
1
4
5
1
4
13
Installation Instructions
SCREW IN PARTWAY
Drive a mounting screw (from the hardware packet)
partway into each center of the narrow neck of the
keyhole slots marked on the cabinet bottom.
OPTIONAL POWER CORD
KIT JXHC1
An optional Power Cord Connection Kit, model
JXHC1, is available at extra cost from your GE
supplier for installation using a standard 3-prong,
grounded wall outlet. Follow the Installation
Instructions packed with the kit to connect the
power cord to the range hood.
14
15
NOTE: If using optional Power Cord Kit JXHC1,
feed the power cord through the hole in the top
cabinet while raising the hood. Loop any excess
length of cord and tie away with a suitable tape
or tie.
Cabinet
7
3
4
3-prong
wall outlet
(if using cord
connection)
1
1
4
1
3
4dia. clearance hole
for optional power
supply location
C
L
FEED IN WIRES
Lift the hood into position and feed the house
wiring through the wiring knockout.
16
SECURE HOOD
Slide the hood back against the wall. Tighten
the mounting screws. Be sure the screw heads
are in the narrow neck of the keyhole slot.
Keyhole (4)
Mounting
screw (4)
NOTE: DO NOT PUSH ON FAN BLADE. Pushing
on the blade may cause it to interfere with other
hood parts.
17
CONNECT DUCTWORK TO
HOOD
(Ducted installations only)
On 7 round installations, attach the 7 duct
with sheet metal screws through the holes in
the alignment ears.
Use duct tape to make joints secure and air tight.
Duct tape
18
Attachment ear tabs
7round duct
14
FOLLOW ELECTRICAL CODE
Complete the electrical wiring according to
National Electrical Code and local codes.
NOTE: This hood must be permanently grounded.
Connect house wiring (120 VAC) to hood wiring.
20
INSTALL LIGHT BULB
NOTE: A light bulb is not shipped with the hood.
Obtain one locally. Purchase and install a type A15
light bulb with an ordinary screw-base, not more
than 60 watts.
19
Installation Instructions
TROUBLESHOOTING CHECKLIST
If the hood seems to be operating at high speed when
the control is not set on high, or if ventilation seems
inadequate, check the following:
Knockouts not removed from hood.
Damper blade not opening.
Reduced airflow because the duct is too small or
the duct length is too long.
The duct is blocked.
Undersized or restrictive wall or roof cap.
If the hood seems to make excessive noise:
Fan may be hitting the filter. Turn off the fan and
remove the filter. Bend the filter down slightly in the
center (into a dome shape) to allow fan clearance.
Reinstall and adjust as needed.
The fan does not work but the lights do:
Switch power off at the service panel and lock the
service disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
Check the wiring connections. See the CONNECT
WIRING section in these Installation Instructions.
REPLACE WIRING COVER
CONNECT WIRING
Connect house black to hood black wire, house
white to hood white wire and house ground under
green ground screw. Securely tighten the strain
relief clamp onto the house wiring.
Green ground screw
21
22
23
REPLACE FILTER
Make sure fan blade turns freely and replace the
filter. NOTE: Install the metal grease filter if ducted
or the charcoal filter if recirculated.
WARNING: IMPROPER CONNECTION OF
ALUMINUM HOUSE WIRING TO THESE
COPPER LEADS CAN RESULT IN A SERIOUS
PROBLEM. USE ONLY CONNECTORS
DESIGNED FOR JOINING COPPER TO
ALUMINUM AND FOLLOW THE
MANUFACTURER’S RECOMMENDED
PROCEDURE CLOSELY.
The installation is complete. Turn on power at
service panel, and test for proper operation.
Wiring cover
Metal grease filter or charcoal filter
GE Range Hood Warranty.
For The Period Of: GE Will Replace:
One Year Any part of the range hood which fails due to a defect in materials or workmanship.
From the date of the During this limited one-year warranty, GE will also provide, free of charge, all labor and
original purchase in-home service to replace the defective part.
Service trips to your home to teach you how to use
the product.
Improper installation, delivery or maintenance.
Failure of the product if it is abused, misused, or
used for other than the intended purpose or used
commercially.
Replacement of house fuses or resetting of circuit
breakers.
Damage to the product caused by accident, fire, floods
or acts of God.
Incidental or consequential damage caused by possible
defects with this appliance.
Damage caused after delivery.
Product not accessible to provide required service.
What GE Will Not Cover:
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home
use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available, you
may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service Location
for service. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
Installation Instructions
Consumer Support
Safety Instructions Operating Instructions
15
All warranty service provided by our Factory Service Centers, or
an authorized Customer Care
®
technician. To schedule service,
on-line, 24 hours a day, visit us at ge.com, or call 800.GE.CARES
(800.432.2737). Please have serial number and model number
available when calling for service.
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in
this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness
for a particular purpose, are limited to one year or the shortest period allowed by law.
Printed in China
Consumer Support.
GE Appliances Website
ge.com
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
order parts or even schedule service on-line.
Schedule Service ge.com
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at
your convenience 24 hours any day of the year! Or call 800.GE.CARES (800.432.2737) during normal
business hours.
Real Life Design Studio ge.com
GE supports the Universal Design concept—products, services and environments that can be used by
people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and
mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen
design ideas for people with disabilities, check out our Website today. For the hearing impaired, please call
800.TDD.GEAC (800.833.4322).
Extended Warranties ge.com
Purchase a GE extended warranty and learn about special discounts that are available while your warranty
is still in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours.
GE Consumer Home Services will still be there after your warranty expires.
Parts and Accessories ge.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their
homes (VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or
by phone at 800.626.2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause
unsafe operation.
Contact Us ge.com
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
Register Your Appliance ge.com
Register your new appliance on-line—at your convenience! Timely product registration will allow for
enhanced communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the pre-printed registration card included in the packing material.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

GE JV347HWW Manuel utilisateur

Catégorie
Hottes
Taper
Manuel utilisateur

dans d''autres langues