Dolmar AX1821H Le manuel du propriétaire

GB Cordless Grass Shear Instruction manual

F Taille-Herbes sans Fil Manuel d’instructions

D Akku-Grasschere Betriebsanleitung

I Cesoie tagliaerba senza filo Istruzioni per l’uso

NL Accugrasschaar Gebruiksaanwijzing

E Tijeras Inalámbricas para Manual de instrucciones

Hierba

P Tesoura para Poda a Bateria Manual de instruções

DK Batteridreven græsklipper Brugsanvisning

GR Ψαλίδι Γρασιδιού Μπαταρίας Οδηγίες χρήσης

TR Akülü Çim Makası Kullanım kılavuzu

AX-1821H

012738

2

1 012739 2 012128

3 015676 4 012524

5 012523 6 012527

7 012526 8 012525

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

3

9 012528 10 012529

11 012533 12 012535

13 012536 14 012537

16

12

10

11

12

14

17

18

19

20

18

21

22

22 18 13

4

15 012538 16 012539

17 012540 18 012541

19 012542 20 012534

21 012543 22 012544

14

13

23

24

25

22

26

24

27

28

29

18

17

30

17

5

23 012530 24 012531

25 012532 26 012546

27 012545

28 011044

31

32

33

34

35

6

29 012561 30 012562

31 012563 32 012564

33 012565 34 012554

35 012556 36 012555

22

18

13

27

29

28

14

36

37

17

18

14

7

37 012557 38 012558

39 012559 40 012560

41 011045 42 010878

43 013054 44 012550

17

18

19

20

18

37

22

13

38

39

35

40

41

404042

8

45 013055 46 013053

47 013056 48 013057

49 012547 50 012566

43

44

45

46

47

48

9

ENGLISH (Original instructions)

Explanation of general view

SPECIFICATIONS

• Due to our continuing program of research and development, the specifications herein are subject to change without

notice.

• Specifications and battery cartridge may differ from country to country.

• Weight, with battery cartridge, according to EPTA-Procedure 01/2003

Symbols

END010-4

The following show the symbols used for the equipment.

Be sure that you understand their meaning before use.

.................... Take particular care and attention.

....... Read instruction manual.

................... Danger; be aware of thrown objects.

..................Keep bystanders away.

................... Cutting means continues to run after

the motor is switched off.

................... Do not expose to moisture.

.............Only for EU countries

Do not dispose of electric equipment or

battery pack together with household

waste material!

In observance of the European

Directives, on Waste Electric and

Electronic Equipment and Batteries

and Accumulators and Waste Batteries

and Accumulators and their

implementation in accordance with

national laws, electric equipment and

batteries and battery pack(s) that have

reached the end of their life must be

collected separately and returned to an

environmentally compatible recycling

facility.

Intended use

ENE015-1

The tool is intended for cutting lawn edges or sprouts.

1. Red indicator

2. Button

3. Battery cartridge

4. Star marking

5. Indicator lamps

6. Check button

7. Lock-off button

8. Switch trigger

9. Indication lamp

10. Change lever

11. Protrusion on base frame

12. Base frame

13. Shear blades

14. Blade cover

15. Blade frame

16. Groove

17. Locking lever

18. Undercover

19. Press

20. Turn

21. Shear blade

22. Crank

23. Basic alignment line on the tool

housing

24. Pins

25. Recessed part of crank

26. Apply grease

27. Base plate

28. Hole in the base plate of shear

blades

29. Oval holes that are overlapped

30. Groove in the undercover

31. Brush

32. Machine oil

33. Hedge shear blade

34. Hedge shear blade cover

35. Storage case

36. Bent part of the base plate of

shear blades

37. Screws

38. Grass shear blade cover

39. Grass shear blade

40. Trimming direction

41. Tilt the blades

42. Hedge surface to be trimmed

43. String

44. Clamping nuts

45. Chip receiver

46. Screws on the shear blades

47. Blade cover to be always installed

before installing the chip receiver

48. Hook hole

Model AX-1821H

Effective cutting width 160 mm

Stroke per minute (min

-1

) 1,250

Rated voltage D.C. 18 V

Battery cartridge

AP-181/AP-1815/BL1815N/BL1820/

BL1820B

AP-183/BL1830/BL1840/BL1840B/

BL1850/BL1850B

Dimensions (L x W x H) 337 mm x 176 mm x 130 mm 353 mm x 176 mm x 130 mm

Net weight 1.4 kg 1.6 kg

Battery charger LG-184/DC18RC

(Optional accessory)

Blade length of optional hedge shear

blades

200 mm

Cd

Ni-MH

Li-ion

10

CORDLESS GRASS SHEAR

SAFETY WARNINGS

GEB070-4

WARNING! IMPORTANT READ CAREFULLY all

safety warnings and all instructions BEFORE USE.

Failure to follow the warnings and instructions may result

in electric shock, fire and/or serious injury.

Save all warnings and

instructions for future reference.

General instructions

1. To ensure correct operation, user has to read this

instruction manual to make himself familiar with the

handling of the equipment. Users insufficiently

informed will risk danger to themselves as well as

others due to improper handling.

2. Never allow children, persons with reduced physical,

sensory or mental capabilities or lack of experience

and knowledge or people unfamiliar with these

instructions to use the machine, local regulations may

restrict the age of the operator.

3. Use the equipment with the utmost care and attention.

4. Operate the equipment only if you are in good physical

condition. Perform all work calmly and carefully. Use

common sense and keep in mind that the operator or

user is responsible for accidents or hazards occurring

to other people or their property.

5. Never operate the machine while people, especially

children, or pets are nearby.

6. Never use the equipment after consumption of alcohol

or drugs, or if feeling tired or ill.

7. The motor is to be switched off immediately in case

that the equipment shows any problem or abnormal

sign.

8. Switch off and remove the battery cartridge when

resting and when leaving the equipment unattended,

and place it in a safe location to prevent danger to

others or damage to the equipment.

9. Don’t force the equipment. It will do the job better and

with less likelihood of a risk of injury at the rate for

which it was designed.

10. Don’t overreach. Keep proper footing and balance at

all times.

11. Avoid using the machine in bad weather conditions

especially when there is a risk of lightning.

Personal protective equipment

1. Dress properly. The clothing worn should be functional

and appropriate, i.e. it should be tight-fitting but not

cause hindrance. Do not wear either jewelry or

clothing which could become entangled. Wear

protective hair covering to contain long hair.

2. Wear eye protection and stout shoes at all times while

operating the machine.

3. Always wear substantial footwear and long trousers

while operating the machine.

Electrical and battery safety

1. Avoid dangerous environment. Don’t use the

equipment in damp or wet locations or expose it to

rain. Water entering an equipment will increase the

risk of electric shock.

2. Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of fire when used with

another battery pack.

3. Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury and fire.

4. When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys, nails,

screws or other small metal objects, that can make a

connection from one terminal to another. Shorting the

battery terminals together may cause burns or a fire.

5. Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, flush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from the

battery may cause irritation or burns.

6. Do not dispose of the battery(ies) in a fire. The cell

may explode. Check with local codes for possible

special disposal instructions.

7. Do not open or mutilate the battery(ies). Released

electrolyte is corrosive and may cause damage to the

eyes or skin. It may be toxic if swallowed.

Starting up the equipment

1. Make sure that there are no children or other people

nearby, also pay attention to any animals in the

working vicinity. Otherwise stop using the equipment.

2. Before use always check that the equipment is safe

for operation. Check the security of the cutting tool

and the guard and the switch trigger/lever for easy and

proper action. Check for clean and dry handles and

test the function of the start/stop.

3. Check damaged parts before further use of the

equipment. A guard or other part that is damaged

should be carefully checked to determine that it will

operate properly and perform its intended function.

Check for alignment of moving parts, binding of

moving parts, breakage of parts, mounting, and any

other condition that may affect its operation. A guard

or other part that is damaged should be properly

repaired or replaced by our authorized service center

unless indicated elsewhere in this manual.

4. Switch on the motor only when the hands and feet are

away from the cutting tool.

5. Before starting make sure that the cutting tool has no

contact with any objects.

Method of operation

1. Only use the equipment in good light and visibility.

During the winter season beware of slippery or wet

areas, ice and snow (risk of slipping). Always ensure a

safe footing on slopes and be sure to walk and never

run.

2. Take care against injury to feet and hands from the

cutting tool.

3. Never stand on a ladder and run the equipment.

4. Never climb up into trees to perform cutting operation

with the equipment.

5. Never work on unstable surfaces.

6. Remove sand, stones, nails etc. found within the

working range. Foreign particles may damage the

cutting tool and can cause dangerous kick-backs.

7

. Should the cutting tool hit stones or other hard objects,

immediately switch off the motor and inspect the

cutting tool.

11

8. Inspect the cutting tool at short regular intervals for

damage (detection of hairline cracks by means of

tapping-noise test).

9. Before commencing cutting, the cutting tool must have

reached full working speed.

10. The cutting tool has to be equipped with the

appropriate guard. Never run the equipment with

damaged guards or without guards in place!

11. All protective installations and guards supplied with

the equipment must be used during operation.

12. Always remove the battery cartridge from the

equipment:

- whenever leaving the equipment unattended;

- before clearing a blockage;

- before checking, cleaning or working on the

equipment;

- after striking a foreign object;

- whenever the equipment starts vibrating abnormally.

13. Always ensure that the ventilation openings are kept

clear of debris.

14. Cutting means continues to run after the motor is

switched off.

Cutting Tools

1. Employ only the correct cutting tool for the job in hand.

Maintenance instructions

1. The condition of the equipment, in particular of the

cutting tool of the protective devices must be checked

before commencing work.

2. Turn off the motor and remove the battery cartridge

before carrying out maintenance, replacing cutting

tools or cleaning the equipment or cutting tool.

3. Check loose fasteners and damaged parts such as

cracks in the cutting attachment.

4. Follow instructions for lubricating and changing

accessories.

5. When not in use, store the equipment indoors in dry

and high or locked-up place - out of the reach of

children. Clean and maintain before storage.

6. Use only the manufacturer’s recommended

replacement parts and accessories.

7. Inspect and maintain the equipment regularly,

especially before/after use. Have the equipment

repaired only by our authorized service center.

8. Keep handles dry, clean and free from oil and grease.

KEEP FOR FUTURE REFERENCE

WARNING:

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to safety

rules for the subject product. MISUSE or failure to

follow the safety rules stated in this instruction

manual may cause serious personal injury.

General Power Tool Safety

Warnings GEA010-1

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

CORDLESS HEDGE TRIMMER

SAFETY WARNINGS

GEB062-5

1. Keep all parts of the body away from the cutter

blade. Do not remove cut material or hold material

to be cut when blades are moving. Make sure the

switch is off when clearing jammed material. A

moment of inattention while operating the hedge

trimmer may result in serious personal injury.

2. Carry the hedge trimmer by the handle with the

cutter blade stopped. When transporting or

storing the hedge trimmer always fit the cutting

device cover. Proper handling of the hedge trimmer

will reduce possible personal injury from the cutter

blades.

3. Hold the power tool by insulated gripping surfaces

only, because the cutter blade may contact hidden

wiring. Cutter blades contacting a “live” wire may

make exposed metal parts of the power tool “live” and

could give the operator an electric shock.

4. Do not use the hedge trimmer in the rain or in wet or

very damp conditions. The electric motor is not

waterproof.

5. First-time users should have an experienced hedge

trimmer user show them how to use the trimmer.

6. The hedge trimmer must not be used by children or

young persons under 18 years of age. Young persons

over 16 years of age may be exempted from this

restriction if they are undergoing training under the

supervision of an expert.

7. Use the hedge trimmer only if you are in good physical

condition. If you are tired, your attention will be

reduced. Be especially careful at the end of a working

day. Perform all work calmly and carefully. The user is

responsible for all damages to third parties.

8. Never use the trimmer when under the influence of

alcohol, drugs or medication.

9. Work gloves of stout leather are part of the basic

equipment of the hedge trimmer and must always be

worn when working with it. Also wear sturdy shoes

with anti-skid soles.

10. Before starting work check to make sure that the

trimmer is in good and safe working order. Ensure

guards are fitted properly. The hedge trimmer must

not be used unless fully assembled.

11. Make sure you have a secure footing before starting

operation.

12. Hold the tool firmly when using the tool.

13. Do not operate the tool at no-load unnecessarily.

14. Immediately switch off the motor and remove the

battery cartridge if the cutter should come into contact

with a fence or other hard object. Check the cutter for

damage, and if damaged repair immediately.

15. Before checking the cutter, taking care of faults, or

removing material caught in the cutter, always switch

off the trimmer and remove the battery cartridge.

16. Switch off the trimmer and remove the battery

cartridge before doing any maintenance work.

17. When moving the hedge trimmer to another location,

including during work, always remove the battery

cartridge and put the blade cover on the cutter blades.

12

Never carry or transport the trimmer with the cutter

running. Never grasp the cutter with your hands.

18. Clean the hedge trimmer and especially the cutter

after use, and before putting the trimmer into storage

for extended periods. Lightly oil the cutter and put on

the cover. The cover supplied with the unit can be

hung on the wall, providing a safe and practical way to

store the hedge trimmer.

19. Store the hedge trimmer with the cover on, in a dry

room. Keep it out of reach of children. Never store the

trimmer outdoors.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to safety

rules for the subject product. MISUSE or failure to

follow the safety rules stated in this instruction

manual may cause serious personal injury.

IMPORTANT SAFETY

INSTRUCTIONS

ENC011-1

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all

instructions and cautionary markings on (1)

battery charger, (2) battery, and (3) product using

battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively shorter,

stop operating immediately. It may result in a risk

of overheating, possible burns and even an

explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it is

severely damaged or is completely worn out. The

battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

10. Follow your local regulations relating to disposal

of battery.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita/Dolmar

batteries.

Use of non-genuine Makita/Dolmar batteries, or batteries

that have been altered, may result in the battery bursting

causing fires, personal injury and damage. It will also void

the Makita/Dolmar warranty for the Makita/Dolmar tool

and charger.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the battery

cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room

temperature at 10°C - 40°C (50°F - 104°F). Let a hot

battery cartridge cool down before charging it.

4. Charge the battery cartridge if you do not use it for

a long period (more than six months).

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking function on the tool.

Installing or removing battery cartridge

(Fig. 1)

CAUTION:

• Always switch off the tool before installing or removing

of the battery cartridge.

• Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge. Failure to

hold the tool and the battery cartridge firmly may cause

them to slip off your hands and result in damage to the

tool and battery cartridge and a personal injury.

To remove the battery cartridge, slide it from the tool while

sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip it

into place. Insert it all the way until it locks in place with a

little click. If you can see the red indicator on the upper

side of the button, it is not locked completely.

CAUTION:

• Always install the battery cartridge fully until the red

indicator cannot be seen. If not, it may accidentally fall

out of the tool, causing injury to you or someone

around you.

• Do not install the battery cartridge forcibly. If the

cartridge does not slide in easily, it is not being inserted

correctly.

Battery protection system (Lithium-ion

battery with star marking) (Fig. 2)

Lithium-ion batteries with a star marking are equipped

with a protection system. This system automatically cuts

off power to the tool to extend battery life.

The tool will automatically stop during operation if the tool

and/or battery are placed under one of the following

conditions:

13

• Overloaded:

The tool is operated in a manner that causes it to

draw an abnormally high current.

In this situation, release the trigger switch on the tool

and stop the application that caused the tool to

become overloaded. Then pull the trigger switch

again to restart.

If the tool does not start, the battery is overheated. In

this situation, let the battery cool before pulling the

trigger switch again.

• Low battery voltage:

The remaining battery capacity is too low and the tool

will not operate. In this situation, remove and

recharge the battery.

Indicating the remaining battery capacity

(Only for battery cartridges with “B” at the end of the

model number.) (Fig. 3)

Press the check button on the battery cartridge to indicate

the remaining battery capacity. The indicator lamps light

up for few seconds.

015658

NOTE:

• Depending on the conditions of use and the ambient

temperature, the indication may differ slightly from the

actual capacity.

Switch action (Fig. 4)

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, depress the lock-off button and pull the

switch trigger. Release the switch trigger to stop. The

lock-off button can be pressed from either right or left side.

Indication lamp (Fig. 5)

Running the tool allows the indication lamp to show the

battery cartridge capacity status.

When the tool is also overloaded and has stopped during

operation, the lamp lights up in red.

Refer to the following table for the status and action to be

taken for the indication lamp.

Note 1: The time at which the indication lamp lights up varies by the temperature around the work area and the battery

cartridge conditions.

010970

Adjusting the shearing height (Fig. 6)

Changing the position of holding the change lever allows

three-stepped setting for sheared grass height (10 mm,

20 mm, 30 mm).

To change setting, tilt the change lever for the base frame

position and with the change lever tilted move it up or

down along the tool surface until the protrusion on base

frame fits in one of the holes in the tool and release it.

Indicator lamps

Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery may

have

malfunctioned.

Indication lamp Status Action to be taken

The lamp blinks in red. This indicates the appropriate time to

replace the battery cartridge when the

battery power becomes low.

Recharge the battery cartridge as soon

as possible.

The lamp lights up in red. (Note 1) This function works when the battery

power is almost used up. At this time,

tool stops immediately.

Recharge the battery cartridge.

The lamp lights up in red. (Note 1) Autostop due to overload. Turn off the tool.

14

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Installing or removing blade cover

CAUTION:

• Be careful not to contact the shear blade when

installing or removing the blade cover. Contacting the

shear blade may cause personal injuries. (Fig. 7 & 8)

Slide the blade cover from the tool’s side until the shear

blade completely hides itself and then push in it lightly

towards the tool from the front.

To remove the blade cover, take the above installation

procedure in reverse.

Installing or removing base frame

CAUTION:

• Before installing or removing base frame, be sure to

install the blade cover.

• When installing or removing base frame, take care that

your fingers are not be pinched between the tool and

base frame. (Fig. 9)

To remove the base frame, upset the tool and take it out

of the groove grabbing its bottom. (Fig. 10)

To install the base frame, fit the protrusion of base frame

near the change lever into the hole for the sheared grass

height setting. With the base frame so fitted, pull the lower

part of base frame and fit the other part of the base frame

in the groove in the tool.

Installing or removing grass shear blades

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before installing or

removing shear blades. Failure to switch off and

remove the battery cartridge from the tool may result in

serious injury from accidental start-up.

• When replacing the shear blade, always wear gloves

without removing blade cover so that hands and face

does not directly contact the blade. Failure to do so

may cause personal injury.

NOTE:

• Do not wipe off grease from the gear and crank. Failure

to do so may cause damage to the tool.

• For specific way of removing and installing shear

blades refer to the reverse of a package for accessory

shear blades. (Fig. 11)

Remove the base frame and place the tool upside down.

CAUTION:

• Before placing the tool upside down, be sure to remove

the base frame. (Fig. 12)

To remove the shear blade, press the locking lever and

with the locking lever pressed turn the undercover

counterclockwise until the symbol on the undercover is

aligned with the symbol  on the locking lever. (Fig. 13)

Take out the undercover, shear blade and crank in order

from the tool. (Fig. 14)

To install the grass shear blade, prepare the crank,

undercover and new grass shear blade. (Fig. 15)

Take out the blade cover from the old shear blades and fit

it onto the new ones for easy handling during the

replacement of blades. (Fig. 16)

Adjust the three pin position so that these pins are lined

up at right angle in relation to the basic alignment line on

the tool housing. (Fig. 17)

Fit the crank with its recessed part facing upwards onto

the pins. At this time, apply a small amount of grease to

the periphery of the crank using grease that the shear

blades as optional accessory are provided with or that

remains inside gear housing. (Fig. 18)

Overlap the oval hole in the upper blade with that in the

lower one. Move the shear blades so that the hole in the

base plate of shear blades are positioned in the center of

these overlapped oval holes. (Fig. 19)

Turn the shear blades upside down and install it so that

the pins on the tool fit in the hole in the shear blades.

Make sure that the shear blades are set in place securely

as far as they reach the base plate. (Fig. 20)

Place the undercover so that the symbol on the

undercover is aligned with the symbol  on the locking

lever. (Fig. 21)

Press the undercover down and turn the undercover

clockwise while pressing it down until the symbol on

the label is aligned with the symbol  on the locking lever

(the undercover is completely locked.). (Fig. 22)

At this time, make sure that the locking lever fits in the

groove in the undercover.

Remove the blade cover and then turn on the tool to

check it for proper movement.

NOTE:

• When the shear blades do not operate properly, there

is a poor fit between the blades and crank. Redo from

the beginning.

OPERATION

WARNING:

• Keep hands away from blades.

CAUTION:

• Smear the blade before and once per hour during

operation using machine oil or the like.

• Avoid operating the tool under the scorching sunlight

as much as practicable. When operating the tool, be

careful of your physical conditions.

• Hold the tool with one hand. Do not hold the front bulge

of the tool as a grip. (Fig. 23)

Turn the tool on after adjusting the shearing height and

hold it so that the foot of the tool rest on the ground. Then

gently move the tool forward into the area to be cut.

(Fig. 24)

When trimming around curb, fence or trees, move the tool

along them. Be careful for the blade not to contact them.

(Fig. 25)

When trimming sprouts or foliage of a small tree, remove

the base frame from the tool and cut little by little.

Shear big branches to your desired height beforehand

using branch scissors before using this tool.

CAUTION:

• When trimming twigs and foliage, do not attempt to trim

too much at a time. Proceed gently. Also do not attempt

to cut thick branches.

15

• Do not let the shear blades contact the grounds during

operation. The blades will be dulled, causing poor

performance.

• Do not trim wet grass or foliage of small trees.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

Cleaning the tool

Clean out the tool by wiping off dust with a dry or soap-

dipped rag.

CAUTION:

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Shear blade maintenance (Fig. 26 & 27)

After operation, remove dust from both sides of the blade

with wired brush, wipe it off with a rag and then apply

enough low-viscosity oil, such as machine oil etc. and

spray-type lubricating oil.

CAUTION:

• Do not wash the blades in water. Failure to do so may

cause rust or damage on the tool.

• Dirt and corrosion cause excessive blade friction and

shorten the operating time per battery charge.

After use

• To clean off the exterior of the tool, dampen a soft cloth

in a soapy water and wipe gently. Never use thinner or

benzine.

• Do not store the tool in a place where volatile materials

are stored.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Dolmar Authorized Service Centers, always

using Dolmar replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Dolmar tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Dolmar Service Center.

• Grass shear blade assembly

• Grass shear blade cover

• Base frame

• Makita/Dolmar genuine battery and charger

• Long handle attachment

For cordless hedge trimmer use

This tool can be used as a hedge trimmer by using the

hedge shear blade (optional accessory) and 2-way

change set (optional accessory).

To use this tool as a hedge trimmer, replacing the grass

shear blades with the hedge shear blades is required.

For removing the grass shear blades, refer to the

aforementioned section titled “Installing or removing grass

shear blades”. For installing the hedge shear blades, refer

to the section below titled “Installing or removing hedge

shear blades”.

• Hedge shear blade assembly (for Hedge Trimmer)

• 2-way change set consisting of the following two

accessories

• Hedge shear blade cover (for Hedge Trimmer)

• Storage case (for blade bottom section) (Fig. 28)

• Chip receiver for hedge trimming (for Hedge Trimmer)

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Installing or removing hedge shear

blades

CAUTION:

• Before installing or removing shear blades, always be

sure that the tool is switched off and the battery

cartridge is removed.

• When replacing the shear blades, always wear gloves

without removing blade cover so that hands and face

do not directly contact the blade. Failure to do so may

cause personal injury.

NOTE:

• Do not wipe off grease from the gear and crank. Failure

to do so may cause damage to the tool.

• For specific way of removing and installing shear

blades refer to the reverse of a package for accessory

shear blades.

Installing the hedge shear blades (Fig. 29)

Prepare the crank, the undercover and new shear blades.

(Fig. 16)

Adjust the three pin position so that these three pins are

aligned with the basic alignment line on the tool housing.

(Fig. 17)

Fit the crank with its recessed part facing downward onto

the pins. At this time, apply a small amount of grease to

the periphery of the crank using grease that the shear

blades as optional accessory are provided with or that

remains inside gear housing. (Fig. 30)

Overlap the oval hole in the upper blade with that in the

lower one. Move the shear blades so that the hole in the

base plate of shear blades are positioned in the center of

these overlapped oval holes. (Fig. 31)

Take out the blade cover from the old shear blades and fit

it onto the new ones for easy handling during the

replacement of blades. (Fig. 32)

Turn the shear blades upside down and install it so that

pin on the tool fit in the hole in the shear blades. Fit the

bent part of the base plate of the shear blades to the

groove in the tool housing. Then make sure that the base

plate of the shear blades is set in place. (Fig. 33)

Tighten two screws with a coin firmly. (Fig. 34)

Place the undercover so that the symbol on the

undercover is aligned with the symbol  on the locking

lever. (Fig. 35)

Press the undercover down and with the undercover

pressed down turn the undercover clockwise until the

symbol on the label is aligned with the symbol  on the

16

locking lever (the undercover is completely locked.).

(Fig. 22)

At this time, make sure that the locking lever fits in the

groove in the undercover.

CAUTION:

• Never use the tool without installing the undercover on

it.

Remove the blade cover and then turn on the tool to

check it for proper movement.

NOTE:

• When the shear blades do not operate properly, there

is a poor fit between the blades and crank. Redo from

the beginning.

Removing the hedge shear blades

(Fig. 36)

CAUTION:

• Install the blade cover before removing or installing the

shear blades.

Reverse the tool. (Fig. 37)

To remove the shear blades, press the locking lever and

with the locking lever pressed turn the undercover

counterclockwise until the symbol on the undercover is

aligned with the symbol  on the locking lever. (Fig. 38)

Take out the undercover from the tool. (Fig. 39)

Loosen two screws with a coin and remove the shear

blades.

NOTE:

• Do not remove the screws. Without removing the

screws loosened, shear blades can be removed.

(Fig. 40)

Remove the crank from the shear blades.

NOTE:

• The crank may remain in the tool. (Fig. 41)

NOTE:

• In the 2-way usage, the removed grass shear blades

need to be sheared in the blade storage case and

stored for future use.

OPERATION

Refer to the Important Safety Instructions before

operation.

CAUTION:

• Be careful not to accidentally contact a metal fence or

other hard objects while trimming. The blade will break

and may cause serious injury.

• Also, be careful for the shear blade not to contact the

ground.

• Overreaching with a hedge trimmer, particularly from a

ladder, is extremely dangerous. Do not work from

anything wobbly or infirm. (Fig. 42)

Do not attempt to cut branches thicker than 10 mm

diameter with this trimmer. These should first be cut with

shears down to the hedge trimming level.

CAUTION:

• Do not cut off dead trees or similar hard objects. Failure

to do so may damage the tool.

• Do not trim the grass or weeds while using hedge

shear blade. The shear blade may entangle the grass

or weeds. (Fig. 43)

Hold the trimmer with one hand, depress the lock-off

button and pull the switch trigger and then move it in front

of your body. (Fig. 44)

As a basic operation, tilt the blades towards the trimming

direction and move it calmly and slowly at the speed rate

of 3 - 4 seconds per meter. (Fig. 45)

To cut a hedge top evenly, it helps to tie a string at the

desired hedge height and to trim along it, using it as a

reference line. (Fig. 46)

Attaching the chip receiver (optional accessory) on the

tool when trimming the hedge straight can avoid cut off

leaves’ being thrown away. (Fig. 47)

To cut a hedge side evenly, it helps to cut from the bottom

upwards. (Fig. 48)

Trim boxwood or rhododendron from the base toward the

top for a nice appearance and good job.

Installing or removing chip receiver

(optional accessory)

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before installing or

removing chip receiver.

NOTE:

• When replacing the chip receiver, always wear gloves

so that hands and face does not directly contact the

blade. Failure to do so may cause personal injury.

• When replacing the chip receiver, always be careful not

to contact the shear blades.

• The chip receiver receives cut-off leaves and alleviates

collecting thrown-away leaves. This can be installed on

either side of the tool. (Fig. 49)

Place the chip receiver on the shear blades so that its slits

overlap with the screws on the shear blades and secure it

using two clamping nuts.

To remove the chip receiver, loosen and remove the two

clamping nuts and then take it out.

Storage (Fig. 50)

The hook hole in the tool bottom is convenient for hanging

the tool from a nail or screw on the wall.

Put the blade cover on the shear blades so that the blades

are not exposed. Store the tool out of the reach of children

carefully.

Store the tool in the place not exposed to water and rain.

Noise

ENG905-1

The typical A-weighted noise level determined according

to IEC60335:

Sound pressure level (L

pA

): 78 dB (A)

Uncertainty (K): 2.5 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined

according to IEC60335:

Vibration emission (a

h

): 2.5 m/s

2

or less

Uncertainty (K): 1.5 m/s

2

17

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to

the trigger time).

Hedge trimming operation with optional hedge shear

blades

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

pA

): 74 dB (A)

Uncertainty (K): 2.5 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Vibration emission (a

h

): 2.5 m/s

2

or less

Uncertainty (K): 1.5 m/s

2

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to

the trigger time).

For European countries only

ENH003-15

EC Declaration of Conformity

Makita declares that the following Machine(s):

Designation of Machine:

Cordless Grass Shear

Model No./Type: AX-1821H

Conforms to the following European Directives:

2006/42/EC

They are manufactured in accordance with the following

standard or standardized documents:

EN60745, EN60335

The technical file in accordance with 2006/42/EC is

available from:

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

30. 9. 2015

Yasushi Fukaya

Director

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

For European countries only

ENH021-8

EC Declaration of Conformity

Makita declares that the following Machine(s):

Designation of Machine:

Cordless Hedge Trimmer

Model No./Type: AX-1821H

Specifications: see “SPECIFICATIONS” table.

Conforms to the following European Directives:

2000/14/EC, 2006/42/EC

They are manufactured in accordance with the following

standard or standardized documents:

EN60745

The technical file in accordance with 2006/42/EC is

available from:

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

The conformity assessment procedure required by

Directive 2000/14/EC was in Accordance with annex V.

Measured Sound Power Level: 82 dB (A)

Guaranteed Sound Power Level: 84 dB (A)

30. 9. 2015

Yasushi Fukaya

Director

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

18

FRANÇAIS (Instructions d’origine)

Descriptif

SPÉCIFICATIONS

• Étant donné l’évolution constante de notre programme de recherche et de développement, les spécifications

contenues dans ce manuel sont sujettes à des modifications sans préavis.

• Les spécifications et la batterie peuvent varier d’un pays à l’autre.

• Poids, batterie incluse, selon la procédure EPTA 01/2003

Symboles

END010-4

Les symboles utilisés pour l’appareil sont indiqués ci-

dessous. Assurez-vous d’avoir bien compris leur

signification avant d’utiliser l’appareil.

.................... Usez d’attention et de soins

particuliers !

....... Reportez-vous au manuel

d’instructions.

................... Danger ; faites attention au risque de

projection d’objets.

.................. Éloignez les spectateurs.

................... L’organe de coupe continue à

fonctionner une fois le moteur éteint.

...................Tenez l’appareil à l’abri de l’humidité.

.............Pour les pays européens uniquement

Ne pas jeter les appareils électriques et

les bloc-batteries dans les ordures

ménagères !

Conformément aux directives

européennes relatives aux déchets

d’équipements électriques ou

électroniques (DEEE) ainsi qu’aux

batteries, aux accumulateurs et aux

batteries et accumulateurs usagés et à

leur transposition dans la législation

nationale, les appareils électriques, les

batteries et les bloc-batteries doivent

être collectés à part et être soumis à un

1. Voyant rouge

2. Bouton

3. Batterie

4. Étoile

5. Voyants

6. Bouton de vérification

7. Bouton de sécurité

8. Gâchette

9. Voyant

10. Levier de changement

11. Saillie sur le châssis

12. Châssis

13. Lames de cisailles

14. Couvercle de protection de la

lame

15. Châssis de la lame

16. Rainure

17. Levier de verrouillage

18. Couvercle supérieur

19. Appuyez

20. Tournez

21. Lame de cisailles

22. Bielle

23. Repère d’alignement de base sur

le carter de l’outil

24. Clous

25. Partie encastrée de la bielle

26. Appliquer de la graisse

27. Plaque de base

28. Orifice dans la plaque de base

des lames de cisailles

29. Orifices ovales qui se

chevauchent

30. Rainure dans le couvercle

supérieur

31. Brosse

32. Huile pour machine

33. Lame de cisailles pour haie

34. Couvercle de protection de la

lame de cisailles pour haie

35. Étui de rangement

36. Partie incurvée de la plaque de

base des lames de cisailles

37. Vis

38. Couvercle de protection de la

lame du taille-herbes

39. Lame du taille-herbes

40. Sens de la taille

41. Inclinez les lames

42. Surface de la haie à tailler

43. Ficelle

44. Écrous de serrage de collier

45. Récepteur de copeaux

46. Vis sur les lames de cisailles

47. Couvercle de protection de la

lame à installer

systématiquement avant

d’installer le récepteur de

copeaux

48. Orifice du crochet

Modèle AX-1821H

Largeur de coupe effective 160 mm

Passes par minute (min

-1

) 1 250

Tension nominale 18 V C.C.

Batterie

AP-181/AP-1815/BL1815N/BL1820/

BL1820B

AP-183/BL1830/BL1840/BL1840B/

BL1850/BL1850B

Dimensions (L x P x H) 337 mm x 176 mm x 130 mm 353 mm x 176 mm x 130 mm

Poids net 1,4 kg 1,6 kg

Chargeur de batterie LG-184/DC18RC

(Accessoire fourni en option)

Longueur de lames de cisailles pour haie

fournies en option

200 mm

Cd

Ni-MH

Li-ion

19

recyclage respectueux de

l’environnement.

Utilisations

ENE015-1

Cet outil a été conçu pour couper les bordures ou les

pousses d’arbres.

AVERTISSEMENTS DE SÉCURITÉ

CONCERNANT LE TAILLE-

HERBES SANS FIL

GEB070-4

AVERTISSEMENT ! IMPORTANT LISEZ

ATTENTIVEMENT toutes les consignes de sécurité et

toutes les instructions AVANT D’UTILISER L’OUTIL. Il

y a un risque de choc électrique, d’incendie et/ ou de

blessure grave si les consignes et les instructions ne sont

pas toutes respectées.

Conservez toutes les consignes

et instructions pour référence

ultérieure.

Instructions générales

1. Pour une utilisation correcte, lisez ce mode d’emploi

afin de vous familiariser avec le fonctionnement de

l’appareil. Sans ces informations, vous risquez de ne

pas utiliser l’appareil correctement et de vous mettre

en danger ou de blesser d’autres personnes.

2. Ne laissez jamais les enfants, les personnes dont les

capacités physiques, sensorielles ou mentales sont

réduites, n’ayant aucune expérience ni compétence,

ou ne connaissant pas les présentes instructions

utiliser l’appareil. Les réglementations locales peuvent

limiter l’âge de l’opérateur.

3. N’utilisez l’appareil qu’avec une précaution et une

attention extrêmes.

4. Utilisez l’appareil uniquement si vous êtes en bonne

condition physique. Effectuez tout le travail avec

calme et prudence. Faites preuve de bon sens et

gardez à l’esprit que l’opérateur ou l’utilisateur est

responsable des accidents ou blessures infligés à

d’autres personnes ou à leurs biens.

5. N’utilisez jamais l’appareil lorsque des personnes,

particulièrement des enfants, ou des animaux se

trouvent à proximité.

6. N’utilisez jamais l’appareil après avoir consommé de

l’alcool ou de la drogue, ou bien si vous vous sentez

fatigué ou malade.

7. Éteignez immédiatement le moteur si vous constatez

un problème ou une anormalité avec l’appareil.

8. Lorsque vous rangez l’appareil et que vous le laissez

sans surveillance, mettez-le hors tension, retirez la

batterie et placez-le en lieu sûr pour protéger les

autres et éviter que l’appareil ne s’abîme.

9. N’utilisez pas l’appareil au-dessus des capacités pour

lesquels il a été conçu : cela pourrait nuire à la qualité

du travail et provoquer un risque de blessures.

10. Ne tendez pas le bras de manière excessive.

Assurez-vous d’une bonne prise au sol et d’une bonne

position d’équilibre à tout moment.

11. Évitez d’utiliser l’appareil lorsque les conditions

météorologiques sont mauvaises, en particulier en

cas de risque d’orage.

Dispositif de protection individuelle

1. Portez des vêtements adéquats. Les vêtements que

vous portez doivent être fonctionnels et appropriés,

c’est-à-dire qu’ils doivent être près du corps, sans

pour autant gêner vos mouvements. Ne portez pas de

bijoux ou de vêtements susceptibles d’être happés par

l’appareil. Portez un filet de protection pour

envelopper les cheveux longs.

2. Portez toujours des lunettes de protection et des

chaussures solides lors de l’utilisation de l’appareil.

3. Portez toujours des chaussures résistantes et des

pantalons longs lors de l’utilisation de l’appareil.

Sécurité électrique et de la batterie

1. Évitez les environnements dangereux. N’utilisez pas

l’appareil dans des lieux humides et ne l’exposez pas

aux intempéries. Le risque de choc électrique

augmente lorsque de l’eau pénètre dans un appareil

électrique.

2. N’utilisez que le chargeur spécifié par le fabricant. Un

chargeur qui convient à un type de batterie peut créer

un risque d’incendie s’il est utilisé avec un autre type

de batterie.

3. Utilisez les outils électriques uniquement avec les

batteries désignées. L’utilisation d’autres types de

batterie peut créer un risque de blessures et

d’incendie.

4. Lorsque le bloc-batterie n’est pas utilisé, gardez-le

éloigné de tout objet métallique, comme les

trombones, pièces, clefs, clous, vis ou autres petits

objets métalliques, qui peuvent faire office de

connexion d’une borne à l’autre. Court-circuiter les

bornes de la batterie peut provoquer des brûlures ou

un incendie.

5. En cas de mauvaise utilisation, du liquide peut fuir de

la batterie ; évitez tout contact. Si un contact

accidentel se produit, nettoyez avec de l’eau. Si le

liquide entre en contact avec les yeux, consultez un

médecin. Le liquide émis par la batterie peut

provoquer une irritation ou des brûlures.

6. Ne jetez pas les batteries au feu. Elles risqueraient

d’exploser. Consultez la réglementation locale pour

connaître les éventuelles consignes de mise au rebut

spéciales.

7. N’ouvrez pas les batteries et n’essayez pas de les

démonter. L’électrolyte libéré est corrosif et risquerait

de blesser vos yeux ou votre peau. Si vous l’avalez, il

peut se révéler toxique.

Démarrage de l’appareil

1. Assurez-vous qu’aucun enfant ou adulte ne se trouve

à proximité et faites attention aux animaux situés dans

la zone de travail. Le cas échéant, arrêtez l’appareil.

2. Avant d’utiliser l’appareil, vérifiez toujours qu’il ne

présente aucun danger. Vérifiez la sécurité de l’outil

tranchant et de son protège-lame, ainsi que le

fonctionnement de la gâchette et du levier. Vérifiez

que les poignées sont propres et sèches, ainsi que le

bon fonctionnement de l’interrupteur marche/arrêt.

3. Recherchez les éventuelles pièces endommagées

avant de continuer à utiliser l’appareil. Un protège-

lame ou une autre pièce endommagé(e) doit être

inspecté(e) soigneusement pour déterminer s’il/si elle

va f

onctionner correctement. Assurez-vous que les

pièces en mouvement sont alignées et se déplacent

20

librement, qu’aucune pièce n’est cassée, que les

pièces sont correctement montées et qu’aucune

anomalie ne risque d’affecter le fonctionnement de

l’appareil. Un protège-lame ou toute autre pièce

endommagé(e) doit être correctement réparé(e) ou

remplacé(e) par un centre de service agréé, sauf

indication contraire dans ce manuel.

4. Ne mettez le moteur sous tension que lorsque vos

mains et vos pieds sont éloignés de la lame.

5. Avant de commencer, assurez-vous que l’outil de

coupe ne touche aucun objet.

Mode d’emploi

1. N’utilisez l’appareil que dans des conditions

d’éclairage et de luminosité suffisantes. En hiver,

soyez attentif aux zones glissantes ou mouillées, au

verglas et à la neige (risque de glissade). Assurez-

vous toujours d’avoir une bonne prise au sol sur les

pentes ; marchez et ne courrez pas.

2. Faites attention à ne pas vous blesser les pieds et les

mains avec l’outil de coupe.

3. N’utilisez jamais l’appareil sur une échelle.

4. Ne montez jamais dans un arbre pour utiliser

l’appareil.

5. Ne travaillez jamais sur des surfaces instables.

6. Enlevez le sable, les pierres, les clous, etc., trouvés à

l’intérieur du périmètre de travail. Des corps étrangers

peuvent endommager l’outil de coupe et causer des

chocs en retour dangereux.

7. Si l’outil de coupe heurte des pierres ou d’autres

objets durs, éteignez de suite le moteur et examinez

l’outil de coupe.

8. Examinez l’outil de coupe à intervalles réguliers courts

pour voir s’il n’a pas subi de dommages (détection de

fissures capillaires en utilisant le test de tapping).

9. Avant de commencer à couper, assurez-vous que

l’outil de coupe a atteint sa vitesse de fonctionnement

maximale.

10. L’outil de coupe doit toujours être équipé de son

protège-lame approprié. N’utilisez jamais l’appareil si

les protège-lames sont endommagés ou s’ils ne sont

pas en place !

11. Vous devez utiliser tous les carters et dispositifs de

protection fournis avec l’appareil pendant son

utilisation.

12. Retirez toujours la batterie de l’appareil :

- toutes les fois où l’appareil doit être laissé sans

surveillance ;

- avant toute opération de retrait d’obstruction ;

- avant toute opération de vérification, de nettoyage

ou de réparation de l’appareil ;

- après avoir heurté un objet étranger ;

- dès que l’appareil commence à vibrer de manière

anormale.

13. Assurez-vous toujours que les ouvertures de

ventilation ne sont pas obstruées par des débris.

14. Les éléments coupants continuent à fonctionner après

l’arrêt du moteur.

Outils de coupe

1. Utilisez uniquement l’outil de coupe adapté au travail.

Instructions d’entretien

1. Avant d’utiliser l’appareil, vérifiez son état, et

notamment l’outil de coupe et les dispositifs de

protection.

2. Avant d’effectuer une opération d’entretien, de

remplacer les lames ou de nettoyer l’appareil ou la

lame, mettez le moteur hors tension et retirez la

batterie.

3. Vérifiez que les dispositifs de fixation sont bien

attachés et recherchez les éventuelles pièces

endommagées, comme des fissures sur la fixation de

l’outil de coupe.

4. Suivez les instructions de lubrification et de

changement des accessoires.

5. Lorsque vous n’utilisez pas l’appareil, rangez-le en

intérieur, dans un endroit sec et, élevé ou verrouillé,

hors de portée des enfants. Nettoyez l’appareil et

effectuez les opérations d’entretien avant de le ranger.

6. N’utilisez que les pièces et accessoires de

remplacement recommandés par le fabricant.

7. Inspectez et assurez régulièrement l’entretien de

l’appareil, particulièrement avant/après utilisation. Ne

faites réparer l’appareil que par notre centre de

service agréé.

8. Gardez les poignées de l’outil sèches, propres et

exemptes d’huile ou de graisse.

CONSERVER POUR RÉFÉRENCE

ULTÉRIEURE.

AVERTISSEMENT:

NE vous laissez PAS tromper (au fil d’une utilisation

répétée) par un sentiment d’aisance et de familiarité

avec le produit, en négligeant le respect rigoureux

des consignes de sécurité qui accompagnent l’outil.

Une UTILISATION INCORRECTE de l’outil ou un non-

respect des consignes de sécurité indiquées dans ce

manuel d’instructions peuvent causer des blessures

graves.

Consignes de sécurité générales

des outils électriques

GEA010-1

AVERTISSEMENT Veuillez lire toutes les

consignes de sécurité et les instructions. Il y a un

risque de choc électrique, d’incendie et/ou de blessure

grave si les consignes et les instructions ne sont pas

toutes respectées.

Conservez toutes les consignes

et instructions pour référence

ultérieure.

CONSIGNES DE SÉCURITÉ

CONCERNANT LE TAILLE-HAIE

SANS FIL

GEB062-5

1. Maintenez toutes les parties du corps éloignées

de la lame de coupe. Ne retirez pas et ne retenez

pas le matériau à couper lorsque les lames sont

en mouvement. Assurez-vous que l’outil est éteint

lors du dégagement des matériaux enchevêtrés.

Tout moment d’inattention pendant l’utilisation du

taille-haie comporte un risque de blessure corporelle

grave.

La page charge ...

Dolmar AX1821H Le manuel du propriétaire

Dolmar AX1821H Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents