Haier WS**GA(E) Manuel utilisateur

Catégorie
Boissons glacées
Taper
Manuel utilisateur

Ce manuel convient également à

WS**GDB(E)
WS**GA(E)
Cantina per vini
- Manuale dell'utente
Bodega
- Manual del usuario
Weinkühlschrank
Bedienungsanleitung
Cave à vin
- Mode d'emploi
Wijnkast
- Gebruikershandleiding
Vinotéka
Uživatelská příručka
Chłodziarka do wina
- Instrukcja Obsługi
Холодильник для вина
Руководство пользователя
Wine Cellar
- User Manual
9
3
3
WS25GA
WS50GA
9
50
49
25
WS49GDB
14
46
WS46GDBE
46
WS59GAE
59
9
9
9
5
5
9
9
9
9
5
5
18
18
18
WS30GA
30 30 32 33
WS30GAE WS32GAE WS33GAE
WS59GAE
WS49GDB
WS46GDBE
White
Down
TEMPER ATURE
Up
On
/
Off
Red
13
TEMPERATURE
Down
Up
White
Red
On/Off
1
3
4
6
7
8
9
8
10
11
13
12
14
2
5
WS25GA
WS59GAE
White
Down
TEMPER ATURE
Up
On
/
Off
Red
8
15
13
14
WS30GA
WS30GAE
8
8
WS32GAE
WS33GAE
Table Of Contents
Important safeguards......................................................................1
Installing Your Wine Cellar .............................................................2
Unpacking Your Wine Cellar .............................................................2
Leveling Your Wine Cellar.................................................................2
Proper Air Circulation ........................................................................2
Electrical Requirement ......................................................................3
Install Limitations...............................................................................3
Use of Extension Cord.......................................................................3
Wine Cellar Features And Use .......................................................4
Initial Setup........................................................................................4
Temperature Adjustments .................................................................4
Shelving.............................................................................................6
Interior Light.......................................................................................6
Normal Operating Sounds You May Hear.........................................6
Proper Wine Cellar Care and Cleaning..........................................7
Cleaning and Maintenance................................................................7
Power Interruptions ...........................................................................7
Vacation and Moving Care ................................................................7
Troubleshooting ..............................................................................8
PAGE
English
IMPORTANT SAFEGUARDS
When using this appliance, always exercise basic safety precautions,
including the following:
1. Read all of the instructions before using this appliance.
2. Use this appliance only for its intended purpose as described in this use
and care guide.
3. This wine cellar must be properly installed in accordance with the
installation instructions before it is used.
instructions in the installation section of this manual.
4. It is intended strictly for household use. If using it for industrial or
commercial purpose, be sure to observe the relevant regulations
and national laws. This appliance is not intended for use by persons (in-
cluding children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given super-
vision or instruction concerning use of the appliance by
a person resp-
onsible for their safety. Child should be supervised to ensure that they
do not play with the appliance.
5. The appliance must be positioned so that the plug is accessible.
6. If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
7. Keep ventilation openings, in the appliance enclosure or in the built-in
structure, clear of obstruction.
8. Do not use mechanical devices or other means to accelerate the
defrosting process, other than those recommended by the manufacturer.
9. Do not damage the refrigerant circuit.
10. Do not use electrical appliances inside the food storage compartments
of the appliance, unless they are of the type recommended by the
manufacturer.
11. If the light is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
12. This appliance is intended to be use
d exclusively for the storage of wine.
13. Risk of child entrapment. Before you throw away your old wine cellar, take
off the doors. Leave the shelves in place so that children may not easily
climb inside.
1
English
Refer to the earthing / grounding
2
English
Unpacking Your Wine Cellar
1. Remove all packaging material. This includes the foam base and
all adhesive tape holding the wine cellar accessories inside and
outside.
2. Inspect and remove any remains of packing, tape or printed
materials before powering on the wine cellar.
Leveling Your Wine Cellar
Your wine cellar has leveling feet which are located in the front
and rear corners of your wine cellar. After properly placing your
wine cellar in its final position, you can level your wine cellar.
The leveling feet can be adjusted by turning them clockwise to
raise your wine cellar or by turning them counterclockwise to lower
your wine cellar. The wine cellar door will close easier when the
leveling feet are extended.
Proper Air Circulation
To assure your wine cellar works at the maximum efficiency it
was designed for, you should install it in a
location where there is
proper air circulation, plumbing and electrical connections.
The following are recommended clearances around the wine
cellar:
Sides .......................... 2" (50mm)
Top ............................. 2" (50mm)
Back ........................... 2" (50mm)
Do not over fill your wine cellar for proper wine cooling.
Note: If your wine cellar has been tilted for any reason, wait 24 hours
before plugging it in.
Installing Your Wine Cellar
3
English
Electrical Requirement
Make sure there is a suitable power Outlet (220-240V, 15 amps
outlet) with proper grounding to power the wine cellar.
Avoid the use of plug adapters or cutting off the third
in order to accommodate a two plug outlet. This
is a
dangerous practice since it provides no effective earth or grou-
nding the wine cellar and may result in shock hazard.
Install Limitations
Do not install your wine cellar in any location not properly insulated
or heated e.g. garage etc. Your wine cellar was not designed to
operate in ambient temperature below 16°C.
Select a suitable location for the wine cellar on a hard even surface
away from direct sunlight or heat source e.g. radiators, under floor
heaters, cooking appliances etc. Any floor unevenness should
b
e corrected with the leveling feet located on
bottom corners of the wine cellar.
Your wine cellar is designed for free-standing installation only. It is
not designed for built-in application.
Use of Extension Cord
Avoid the use of an extension
potential safety
hazards under certain conditions. If it is nec-
essary to use an
extension cord, use only an extension cord that
has a plug and an
outlet with grounding function. The marked
rating of the extension
cord must be equal to or greater than the
electrical rating of the
appliance.
earth
or grounding pin
leads, cables or cords because of
the front and rear
4
English
Wine Cellar Features And Use
Initial Setup
Once you have plugged the unit into an electrical outlet, let the unit
run for at least 30 minutes to acclimatize itself before making any
adjustments.
Temperature Adjustments:
WS50GA
See
The temperature of wine cellar is preset to 12 °C (54 °F) from the
factory.
The wine cellar can be set to any temperature between 5
°C (41 °F) and 20 °C (68 °F) in either the compartments to
accommodate your wine storage requirements. To set the
temperature hold the "
" button for about 3 seconds. You
will notice the temperature display blink. Press the "
" or
"" button to increase or decrease the temperature setting.
Once the desired temperature is attained, press the "
" button or
stop operation about 5 seconds, panel will memorize the setting. The
temperature display will revert back to display the inside temperature.
It may take some time to reach the set temperature.
Press the "
" button about 3 seconds to transform "°C" and "°F"
(the temperature display model) each other.
WS49GDB/WS46GDBE
See
The wine cellar is preset from the factory to automatically to
accommodate temperature requirements for red or white wines.
The wine cellar can be set to any temperature between 6 °C and
18 °C in either of the compartments to accommodate your wine
storage requirements. To set the temperature hold the "
" button
for about 3 seconds. You will notice the temperature display blink
for the upper compartment. Press the up or down arrow button to
increase or decrease the temperature setting. Once the desired
temperature is attained, press the "
" button. Doing this, the
electronic control panel will memorize the setting. The temperature
display will revert back to display the inside temperature. It may
take some time to reach the set temperature.
5
English
Once the temperature is set for the upper compartment, you will
notice the temperature display blink for the lower compartment.
Again press the up or down arrow button to increase or decrease
the temperature. Once the desired temperature is attained, press
the "
" button. Doing this, the electronic control panel will
memorize the setting. The temperature display will revert back to
display the inside temperature. It may take some time to reach the
set temperature.
WS25GA/WS59GAE/WS30GA
WS30GAE/WS32GAE/WS33GAE
See
The wine cellar is preset from the factory to automatically
accommodate temperature requirements for red or white wines.
If you store mostly white wines, press the "
" button
and the wine cellar will maintain an average temperature between
to 10 °C. Pushing the "
" button will yield an average
temperature between 13 °C to 16 °C.
The wine cellar can be set to any temperature you desire to
accommodate your wine storage requirements. To set the
temperature, press both the "
" and " " buttons
simultaneously and hold for approximately 3 seconds. Now you are
in temperature set mode. Decrease the temperature by pushing
the "
" button and increase the temperature by pressing
the "
" button. Pressing the appropriate button 3 times will
adjust the temperature 3 degrees, press 4 times equals 4 degrees,
5 times equals 5 degrees, and so on. Once you have selected the
temperature you desire, push the "
" button. Now the wine
cellar is programmed and the LED readout will return to current
internal temperature reading.
Wine Cellar Features And Use
Note: You can add water to the tray to increase the humidity inside
the wine cellar. Some degree of humidity is required in order to keep
wines with corks from drying out. Even when wine bottles are stored
on their sides, one end of the cork is still exposed to air. If the cork
begins to dry out, it can allow oxygen to enter the bottle, filling the u-
llage space and possibly causing the wine to spoil or oxidize. Exces-
sive humidity can also pose the risk of damaging wine labels, which
may hinder identification or hurt potential resale value.
6
English
Shelving
The shelves are designed for appearance and easy cleaning.
Larger bottles or Magnums can be more easily accommodated at
the cross shelves at the bottom of the cellar.
There are some shelves for easy storage and removal of your
wine.
Interior Light
To complement the look of your wine collection, a light has been
built into the wine cellar. Simply push the "
" or " " button
and the light comes on, push again for off. For maximum energy
efciency, leave light off when not viewing your collection.
When door is open the light will go on. Upon closing the door, the
light will go off.(Except WS30GA/WS30GAE/WS32GAE/WS33GAE)
Normal Operating Sounds You May Hear
Boiling water, gurgling sounds or slight vibrations that are the
result of the refrigerant circulating through the cooling coils.
The thermostat control will click when it cycles on and off.
7
English
To avoid electric shock always unplug your wine cellar
before cleaning. Ignoring this warning may result in
death or injury.
Before using cleaning products, always read and follow
manufacturer's instructions and warnings to avoid
personal injury or product damage.
Prepare a cleaning solution of 3-4 tablespoons of
baking soda mixed with warm water. Use sponge or
soft cloth, dampened with the cleaning solution, to
wipe down your wine cellar.
Rinse with clean warm water and dry with a soft cloth.
Do not use harsh chemicals, abrasives, ammonia,
chlorine bleach, concentrated detergents, solvents or
metal scouring pads. Some of these chemicals may
dissolve, damage and/or discolor your wine cellar.
Clean door gaskets every three months according to
general instructions. Gaskets must be kept clean and
pliable to assure a proper seal.
Petroleum jelly applied lightly on the hinge side of
gaskets will keep the gasket pliable and assure a
good seal.
Power Interruptions
Occasionally there may be power interruptions due to
thunderstorms or other causes. Remove the power cord from
AC outlet when a power outage occurs. When power has been
restored, replug power cord to AC outlet.
Vacation and Moving Care
For long vacations or absences, unplug the wine cellar and clean
the wine cellar and door gaskets according to "General cleaning"
section. Leave doors open, so air can circulate inside.
When moving always move the wine cellar vertically. Do not move
with the unit lying down, as possible damage to the sealed system
could occur.
Note: After moving, wait for 24 hours before plugging in the wine
cellar.
Warning:
Caution:
Generall:
Door Gaskets:
Proper Wine Cellar Care and Cleaning
Cleaning and Maintenance
8
English
Wine Cellar Does Not Operate:
Check if wine cellar is plugged in.
Check if there is power in the AC outlet, by checking the circuit
breaker.
Wine appears too warm:
Frequent door openings.
Allow time for recently added wine to reach desired temperature.
Check gaskets for proper seal.
Clean condenser coils.
Adjust temperature control to colder setting.
Wine temperature is too cold:
If temperature control setting is too cold, adjust to a warmer
setting.
Wine cellar runs too frequently:
This may be normal to maintain constant temperature during high
temperature and humid days.
Doors may have been opened frequently or for an extended period
of time.
Clean condenser coils.
Check gasket for proper seal.
Check to see if doors are completely closed.
Moisture build up on interior or exterior of the wine cellar:
This is normal during high humidity periods.
Prolonged or frequent door openings.
Check door gaskets for proper seal.
Wine cellar door does not shut properly:
Level the wine cellar.
Check for blockages e.g. wine bottles, shelves.
Do not dispose of electrical appliances as unsorted
municipal waste, use separate collection facilities.
Contact you local government forinformation
regarding the collection systems available. If electrical
appliances are disposed of in landfills or dumps,
hazardous substances can leak into the groundwater
and get into the food chain, damaging your health and
well-being. When replacing old appliances with new
ones, the retailer is legally obligated to take back your
old appliance for disposals at least free of charge.
TroubleShooting
After Sales Service and Support.
In event of trouble refer to the warranty card for after sales service and
support information or go to www.haier.com and go to the Service and
Support tab and either e-mail or telephone the Service Centre.
Sommario
Importanti misure di sicurezza.......................................................1
Installazione della cantina ..............................................................2
Disimballaggio della cantina per vini .................................................2
Messa in piano della cantina per vini.................................................2
Circolazione adeguata dell'aria .........................................................2
Requisiti elettrici ................................................................................3
Limitazioni per l'installazione .............................................................3
Utilizzo di cavi di prolunga.................................................................3
Funzioni e utilizzo della cantina per vini.......................................4
......................................................................4
Regolazione della temperatura..........................................................4
Ripiani................................................................................................6
Luce interna.......................................................................................6
Rumori durante il funzionamento.......................................................6
Pulizia e manutenzione corrette della cantina per vini................7
Pulizia e manutenzione .....................................................................7
Interruzioni di corrente.......................................................................7
Manutenzione in caso di vacanze e trasporti ....................................7
Risoluzione dei problemi................................................................8
PAGINA
Italiano
IMPORTANTI MISURE DI SICUREZZA
Durante l'utilizzo dell'apparecchio, seguire sempre le precauzioni di
sicurezza basilari, tra cui:
1. Leggere tutte le istruzioni prima di utilizzare l'apparecchio.
2. Utilizzare l'apparecchio solo per lo scopo previsto, in base a quanto descritto
nella presente guida relativa all'utilizzo e alla manutenzione.
3. Prima dell'utilizzo, la cantina per vini deve essere accuratamente installata
in conformità alle istruzioni di installazione fornite. Vedere le istruzioni sulla
messa a terra nella sezione relativa all'installazione.
4. L'apparecchio è destinato esclusivamente all'uso domestico. Se utilizzato
per scopi industriali o commerciali, assicurarsi di osservare le normative in
materia. Questo apparecchio non è idoneo per l'uso da parte di persone
(inclusi bambini) con capacità fisiche, sensoriali o mentali limitate o prive
dell'adeguata esperienza e conoscenza del suo utilizzo, a meno che non
vengano sorvegliate o non ricevano istruzioni da un responsabile per la
sicurezza.
Sorvegliare i bambini, per assicurarsi che non giochino con l'apparecchio.
5. Posizionare l'apparecchio in modo che la spina sia facilmente accessibile.
6. Se il cavo di alimentazione è danneggiato, contattare il produttore, un tecnico
dell'assistenza o un'altra persona qualificata per la sostituzione, al fine di
evitare rischi.
7. Mantenere libere da ostruzioni le aperture di ventilazione nell'involucro
dell'apparecchio o nella struttura a incasso.
8. Non utilizzare nessuno strumento per accelerare il processo di sbrinamento,
ad eccezione di quelli consigliati dal produttore.
9. Non danneggiare il circuito del refrigeratore.
10. Non utilizzare apparecchi elettrici nei vani di conservazione degli alimenti, ad
eccezione di quelli di tipo consigliato dal produttore.
11. Se la spia è danneggiata, deve essere sostituita dal produttore, da un tecnico
dell'assistenza o da altra persona qualificata per la sostituzione, al fine di
evitare rischi.
12. Questo apparecchio è concepito per essere utilizzato esclusivamente per la
conservazione del vino.
13. Rischio di intrappolamento bambini. Prima di disfarsi di una vecchia cantina
per vini, è opportuno rimuovere gli sportelli. Non rimuovere i ripiani per evitare
che i bambini possano introdursi all'interno.
1
Italiano
2
Italiano
Disimballaggio della cantina per vini
1. Rimuovere tutto il materiale di imballaggio, inclusa la base in schiuma e il
nastro adesivo che ssa gli accessori all'interno e all'esterno.
2. Ispezionare e rimuovere eventuali rimanenze dell'imballaggio o di nastro e
qualsiasi materiale stampato prima dell'accensione della cantina.
Messa in piano della cantina per vini
La cantina dispone di piedini per la messa in piano, posizionati agli angoli
anteriori e posteriori. Una volta stabilita la posizione denitiva, effettuare la
messa in piano.
I piedini possono essere regolati, ruotandoli in senso orario per alzare la
cantina e in senso antiorario per abbassarla. L'estensione completa dei
piedini agevola la chiusura e l'apertura dello sportello.
Circolazione adeguata dell'aria
Per garantire il funzionamento ottimale della cantina, è necessario installare
l'apparecchio in una posizione che consenta un'adeguata circolazione
dell'aria e in cui siano presenti i collegamenti elettrici e l'impianto idraulico
corretti.
Spazio libero consigliato attorno alla cantina:
Lati .................................. 50 mm
Piano superiore .............. 50 mm
Retro ............................... 50 mm
Non sovraccaricare la cantina per consentire un corretto raffreddamento
del vino.
Nota: se, per qualche motivo, la cantina è stata inclinata, attendere 24 ore
prima di collegarla all'alimentazione.
Installazione della cantina
3
Italiano
Requisiti elettrici
Vericare la presenza di una presa di corrente idonea (220-240 V, 15 amp)
con messa a terra corretta.
Evitare l'utilizzo di adattatori tripolari o l'adattamento a una presa bipolare
eliminando il polo della messa a terra. Si tratta di un'operazione pericolosa
poiché elimina la messa a terra necessaria per la cantina, con conseguente
pericolo di scosse elettriche.
Limitazioni per l'installazione
Non installare la cantina per vini in ambienti non isolati o riscaldati
correttamente, come garage, ecc. La cantina non è progettata per
funzionare a una temperatura inferiore ai 16 °C.
Scegliere una posizione idonea, con una superficie solida e piana, non
esposta alla luce diretta del sole e lontana da fonti di calore, come radiatori,
riscaldatori a zoccolo, apparecchiature per la cucina, ecc. Eventuali
dislivelli del pavimento possono essere compensati regolando i piedini
posizionati agli angoli anteriori e posteriori della cantina.
La cantina è progettata per essere installata solo autonomamente e non in
strutture a incasso.
Utilizzo di cavi di prolunga
Evitare l'utilizzo di cavi di prolunga che, in alcune condizioni, possono
causare potenziali rischi per la sicurezza. Se è necessario utilizzare un
cavo di prolunga, utilizzare un cavo dotato di spina e terminale di messa
a terra. La tensione elettrica del cavo deve essere uguale o superiore a
quella indicata per l'apparecchio.
4
Italiano
Funzioni e utilizzo della cantina per vini
Configurazione iniziale
Dopo aver collegato l'unità a una presa elettrica, lasciarla in funzione per
almeno 30 minuti per stabilizzare la temperatura, prima di procedere con le
regolazioni desiderate.
Regolazione della temperatura:
WS50GA
Vedere
La temperatura predefinita della cantina è di 12 °C (54 °F).
La temperatura può essere regolata su un valore compreso tra 5 °C (41 °F)
e 20 °C (68 °F) in tutti gli scomparti, in base alle esigenze di conservazione
del vino. Per impostare la temperatura, tenere premuto il tasto "
" per
circa 3 secondi. Il display della temperatura inizierà a lampeggiare. Premere
il tasto "
" o "—" per aumentare o diminuire il valore della temperatura.
Una volta raggiunta la temperatura desiderata, premere il tasto " " o
interrompere l'operazione per 5 secondi; il pannello memorizzerà l'impostazione.
Il display della temperatura tornerà a visualizzare la temperatura interna. È
necessario qualche minuto affinché l'apparecchio raggiunga la temperatura
impostata.
Premere il tasto "
" per circa 3 secondi per passare da C" a F"
(modello del display della temperatura).
WS49GDB/WS46GDBE
Vedere
La cantina per vini è preimpostata dalla fabbrica per adattarsi ai requisiti di
temperatura dei vini rossi o bianchi.
La temperatura della cantina può essere impostata su qualsiasi valore
compreso tra 6 °C e 18 °C in ogni scomparto, in base alle esigenze di
conservazione del vino. Per impostare la temperatura, tenere premuto
il tasto "
" per circa 3 secondi. Il display della temperatura inizierà
a lampeggiare per lo scomparto superiore. Premere i pulsanti freccia
Su o Giù per aumentare o diminuire il valore della temperatura. Una
volta raggiunto il valore desiderato, premere il tasto "
". Il pannello di
controllo memorizzerà l'impostazione. Il display della temperatura tornerà a
visualizzare la temperatura interna. È necessario qualche minuto affinché
l'apparecchio raggiunga la temperatura impostata.
5
Italiano
Una volta impostata la temperatura dello scomparto superiore, il display
della temperatura inizierà a lampeggiare per lo scomparto inferiore.
Premere di nuovo i pulsanti freccia Su o G per aumentare o diminuire
il valore della temperatura. Una volta raggiunto il valore desiderato,
premere il tasto "
". Il pannello di controllo memorizzerà l'impostazione.
Il display della temperatura tornerà a visualizzare la temperatura interna. È
necessario qualche minuto affinché l'apparecchio raggiunga la temperatura
impostata.
WS30GAE/WS32GAE/WS33GAE
WS25GA/WS59GAE/WS30GA
Vedere
La cantina per vini è preimpostata dalla fabbrica per adattarsi ai requisiti di
temperatura dei vini rossi o bianchi. Se vengono conservati in prevalenza
vini bianchi, premere il tasto "
"; la cantina manterrà una
temperatura media compresa tra 7 °C e 10 °C. Premendo il tasto
"
", la temperatura verrà portata a un valore medio compreso tra
13 °C e 16 °C.
La temperatura della cantina può essere impostata su qualsiasi valore
desiderato, in base alle esigenze di conservazione del vino. Per impostare
la temperatura, tenere premuti entrambi i tasti "
" e " "
simultaneamente per circa 3 secondi per entrare nella modalità di
impostazione della temperatura. Diminuire la temperatura premendo il tasto
" " e aumentarla premendo il tasto " ". Premendo
3 volte uno dei tasti, si modifica il valore della temperatura di 3 gradi,
premendolo 4 volte si modifica di gradi, 5 volte di 5 gradi e così via. Una
volta selezionata la temperatura desiderata, premere il tasto " ".
La cantina per vini è ora programmata e il valore visualizzato sul LED
indicherà la temperatura interna attuale.
Nota: versare nell'apposito contenitore la quantità di acqua adeguata per
migliorare l'umidità all'interno della cantina.
Funzioni e utilizzo della cantina per vini
1 / 1

Haier WS**GA(E) Manuel utilisateur

Catégorie
Boissons glacées
Taper
Manuel utilisateur
Ce manuel convient également à