Arthur_Martin AGS6435X Manuel utilisateur

Marque: Arthur_Martin

Modèle: AGS6435X

Catégorie: Plaques de cuisson

Taper: Manuel utilisateur

AGS6435X

EN Hob User Manual 2

FR Table de cuisson Notice d'utilisation 17

CONTENTS

Safety information 2

Safety instructions 4

Installation 6

Product description 10

Daily use 10

Hints and tips 12

Care and cleaning 12

Troubleshooting 13

Technical data 15

Subject to change without notice.

SAFETY INFORMATION

Before the installation and use of the appliance, carefully

read the supplied instructions. The manufacturer is not

responsible for any injuries or damage that are the result of

incorrect installation or usage. Always keep the instructions

in a safe and accessible location for future reference.

Children and vulnerable people safety

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

the use of the appliance in a safe way and understand the

hazards involved.

• Children between 3 and 8 years of age and persons with

very extensive and complex disabilities shall be kept away

from the appliance unless continuously supervised.

• Children of less than 3 years of age should be kept away

from the appliance unless continuously supervised.

• Do not let children play with the appliance.

• Keep all packaging away from children and dispose of it

appropriately.

• Keep children and pets away from the appliance when it

operates or when it cools down. Accessible parts may

become hot during use.

• If the appliance has a child safety device, it should be

activated.

• Children shall not carry out cleaning and user maintenance

of the appliance without supervision.

General Safety

• WARNING: The appliance and its accessible parts

become hot during use. Care should be taken to avoid

touching heating elements.

• WARNING: Unattended cooking on a hob with fat or oil

can be dangerous and may result in fire.

• NEVER try to extinguish a fire with water, but switch off the

appliance and then cover flame e.g. with a lid or a fire

blanket.

• CAUTION: The appliance must not be supplied through an

external switching device, such as a timer, or connected to

a circuit that is regularly switched on and off by a utility.

• CAUTION: The cooking process has to be supervised. A

short term cooking process has to be supervised

continuously.

• WARNING: Danger of fire: Do not store items on the

cooking surfaces.

• Metallic objects such as knives, forks, spoons and lids

should not be placed on the hob surface since they can get

hot.

• Do not use the appliance before installing it in the built-in

structure.

• Do not use a steam cleaner to clean the appliance.

• If the supply cord is damaged, it must be replaced by the

manufacturer, an authorized Service or similarly qualified

persons in order to avoid a hazard.

• Where the appliance is directly connected to the power

supply, an all-pole isolating switch with a contact gap is

required. Complete disconnection in compliance with the

conditions specified in overvoltage category III must be

guaranteed. The earth cable is excluded from this.

• When you route the mains cable, make sure that the cable

doesn't come into direct contact (for example using

insulating sleeving) with parts that can reach temperatures

of more than 50°C above room temperature.

• WARNING: Use only hob guards designed by the

manufacturer of the cooking appliance or indicated by the

manufacturer of the appliance in the instructions for use as

suitable or hob guards incorporated in the appliance. The

use of inappropriate guards can cause accidents.

SAFETY INSTRUCTIONS

This appliance is suitable for the following

markets: DZ MA

Installation

WARNING! Only a qualified

person must install this

appliance.

WARNING! Risk of injury or

damage to the appliance.

• Remove all the packaging.

• Do not install or use a damaged

appliance.

• Follow the installation instructions

supplied with the appliance.

• Keep the minimum distance from other

appliances and units.

• Always take care when moving the

appliance as it is heavy. Always use

safety gloves and enclosed footwear.

• Seal the cut surfaces with a sealant to

prevent moisture to cause swelling.

• Protect the bottom of the appliance

from steam and moisture.

• Do not install the appliance adjacent to

a door or under a window. This

prevents hot cookware falling from the

appliance when the door or the window

is opened.

• If the appliance is installed above

drawers make sure that the space,

between the bottom of the appliance

and the upper drawer, is sufficient for

air circulation.

• The bottom of the appliance can get

hot. Make sure to install a non-

combustible separation panel under the

appliance to prevent access to the

bottom.

Electrical Connection

WARNING! Risk of fire and

electric shock.

• All electrical connections should be

made by a qualified electrician.

• The appliance must be earthed.

• Before carrying out any operation make

sure that the appliance is disconnected

from the power supply.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Make sure the appliance is installed

correctly. Loose and incorrect electricity

mains cable or plug (if applicable) can

make the terminal become too hot.

• Use the correct electricity mains cable.

• Do not let the electricity mains cable

tangle.

• Make sure that a shock protection is

installed.

• Use the strain relief clamp on the cable.

• Make sure the mains cable or plug (if

applicable) does not touch the hot

appliance or hot cookware, when you

connect the appliance to the near

sockets.

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to the

mains plug (if applicable) or to the

mains cable. Contact our Authorised

Service Centre or an electrician to

change a damaged mains cable.

• The shock protection of live and

insulated parts must be fastened in

such a way that it cannot be removed

without tools.

• Connect the mains plug to the mains

socket only at the end of the

installation. Make sure that there is

access to the mains plug after the

installation.

• If the mains socket is loose, do not

connect the mains plug.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• Use only correct isolation devices: line

protecting cut-outs, fuses (screw type

fuses removed from the holder), earth

leakage trips and contactors.

• The electrical installation must have an

isolation device which lets you

disconnect the appliance from the

mains at all poles. The isolation device

must have a contact opening width of

minimum 3 mm.

Gas connection

• All gas connections must be made by a

qualified person.

• Before installation, make sure that the

local distribution conditions (nature of

the gas and gas pressure) and the

adjustment of the appliance are

compatible.

• Make sure that there is air circulation

around the appliance.

• The information about the gas supply is

on the rating plate.

• This appliance is not connected to a

device, which evacuates the products

of combustion. Make sure to connect

the appliance according to current

installation regulations. Follow the

requirements for adequate ventilation.

Use

WARNING! Risk of injury,

burns and electric shock.

• Remove all the packaging, labelling

and protective film (if applicable) before

first use.

• This appliance is for household use

only.

• Do not change the specification of this

appliance.

• Make sure that the ventilation openings

are not blocked.

• Do not let the appliance stay

unattended during operation.

• Set the cooking zone to “off” after each

use.

• Do not put cutlery or saucepan lids on

the cooking zones. They can become

hot.

• Do not operate the appliance with wet

hands or when it has contact with

water.

• Do not use the appliance as a work

surface or as a storage surface.

• When you place food into hot oil, it may

splash.

WARNING! Risk of fire and

explosion

• Fats and oil when heated can release

flammable vapours. Keep flames or

heated objects away from fats and oils

when you cook with them.

• The vapours that very hot oil releases

can cause spontaneous combustion.

• Used oil, that can contain food

remnants, can cause fire at a lower

temperature than oil used for the first

time.

• Do not put flammable products or items

that are wet with flammable products

in, near or on the appliance.

WARNING! Risk of damage to

the appliance.

• Do not keep hot cookware on the

control panel.

• Do not let cookware boil dry.

• Be careful not to let objects or

cookware fall on the appliance. The

surface can be damaged.

• Never leave a burner on with empty

cookware or without cookware.

• Do not put aluminium foil on the

appliance.

• Use only stable cookware with the

correct shape and diameter larger than

the dimensions of the burners.

• Make sure cookware is centrally

positioned on the burners.

• Do not use large cookware that overlap

the edges of the appliance. This can

cause damage to the worktop surface.

• Make sure the flame does not go out

when you quickly turn the knob from

the maximum to the minimum position.

• Use only the accessories supplied with

the appliance.

• Do not install a flame diffuser on the

burner.

• The use of a gas cooking appliance

results in the production of heat and

moisture. Provide good ventilation in

the room where the appliance is

installed.

• Prolonged intensive use of the

appliance may call for additional

ventilation, for example opening of a

window, or more effective ventilation,

for example increasing the level of

mechanical ventilation where present.

• This appliance is for cooking purposes

only. It must not be used for other

purposes, for example room heating.

• Do not let acid liquids, for example

vinegar, lemon juice or limescale

remover, touch the hob. This can cause

matt patches.

• Discoloration of the enamel or stainless

steel has no effect on the performance

of the appliance.

Care and cleaning

WARNING! Do not remove the

buttons, knobs or gaskets from

the control panel. Water may

get inside the appliance and

cause damage.

• Clean the appliance regularly to

prevent the deterioration of the surface

material.

• Deactivate the appliance and let it cool

down before you clean it.

• Disconnect the appliance from the

electrical supply before maintenance.

• Do not use water spray and steam to

clean the appliance.

• Clean the appliance with a moist soft

cloth. Only use neutral detergents. Do

not use any abrasive products,

abrasive cleaning pads, solvents or

metal objects.

• Do not clean the burners in the

dishwasher.

Service

• To repair the appliance contact the

Authorised Service Centre.

• Use original spare parts only.

Disposal

WARNING! Risk of injury or

suffocation.

• Contact your municipal authority for

information on how to discard the

appliance correctly.

• Disconnect the appliance from the

mains supply.

• Cut off the mains electrical cable close

to the appliance and dispose of it.

• Flat the external gas pipes.

INSTALLATION

WARNING! Refer to Safety

chapters.

Before the installation

Before you install the hob, write down the

information below from the rating plate.

The rating plate is on the bottom of the

hob.

Model .......................................

PNC .........................................

Serial number ...........................

Gas Connection

WARNING! The following

instructions about installation,

connection and maintenance

must be carried out by qualified

personnel in compliance with

standards and local regulations

in force.

Choose fixed connections or use a flexible

pipe in stainless steel in compliance with

the regulation in force. If you use flexible

metallic pipes, be careful they do not

come in touch with mobile parts or they

are not squeezed. Also be careful when

the hob is put together with an oven.

Make sure that the gas supply

pressure of the appliance

obeys the recommended

values. The adjustable

connection is fixed to the

comprehensive ramp by means

of a threaded nut G 1/2". Screw

the parts without force, adjust

the connection in the

necessary direction and tighten

everything.

A B C

A. End of shaft with nut

B. Washer supplied with the appliance

C. Elbow supplied with the appliance

WARNING! It is important to

install the elbow correctly.

Make sure that the shoulder is

on the end of the thread. Then

install it on the hob connecting

pipe. Incorrect assembly may

cause a gas leakage.

Liquid gas

Use the rubber pipe holder for liquid gas.

Always engage the gasket. Then continue

with the gas connection.

The flexible pipe is prepared for apply

when:

• it can not get hot more than room

temperature, higher than 30°C;

• it is no longer than 1500 mm;

• it shows no throttles;

• it is not subject to traction or torsion;

• it does not get in touch with cutting

edges or corners;

• it can be easily examined in order to

make sure its condition.

The control of preservation of the flexible

pipe consists in checking that:

• it does not show cracks, cuts, marks of

burnings on the two ends and on its full

length;

• the material is not hardened, but shows

its correct elasticity;

• the fastening clamps are not rusted;

• expired term is not due.

If one or more defects are visible, do not

repair the pipe, but replace it.

WARNING! When installation

is complete, make sure that the

seal of each pipe fitting is

correct. Use a soapy solution,

not a flame!

Injectors replacement

1. Remove the pan supports.

2. Remove the caps and crowns of the

burner.

3. With a socket spanner 7 remove the

injectors and replace them with the

ones which are necessary for the type

of gas you use (see table in "Technical

Data" chapter).

4. Assemble the parts, follow the same

procedure backwards.

5. Attach the label with the new type of

gas supply near the gas supply pipe.

You can find this label in the package

supplied with the appliance.

If the supply gas pressure is changeable

or different from the necessary pressure,

you must fit an applicable pressure

adjuster on the gas supply pipe.

Adjustment of minimum level

To adjust the minimum level of the

burners:

1. Light the burner.

2. Turn the knob on the minimum

position.

3. Remove the knob and the gasket.

4. With a thin screwdriver, adjust the

bypass screw position (A).

5. If you change:

• from natural gas G20 20 mbar to

liquid gas, fully tighten the bypass

screw in.

• from liquid gas to natural gas G20

20 mbar, undo the bypass screw

approximately 1/4 of a turn (1/2 of a

turn for Multi Crown burner).

6. Reassemble the gasket and the knob.

WARNING! Make sure the

flame does not go out when

you quickly turn the knob from

the maximum position to the

minimum position.

Electrical connection

• Make sure that the rated voltage and

type of power on the rating plate agree

with the voltage and the power of the

local power supply.

• This appliance is supplied with a mains

cable. It has to be supplied with a

correct plug which can hold the load

that the rating plate rates. Make sure

that you install the plug in a correct

socket.

• Always use a correctly installed

shockproof socket.

• Make sure that there is an access to

the mains plug after the installation.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• There is a risk of fire when the

appliance is in connection with an

extension cable, an adapter or a

multiple connection. Make sure that the

ground connection agrees with the

standards and regulations.

• Do not let the power cable to heat up to

a temperature higher than 90° C.

Make sure that you connect the

blue neutral cable to the

terminal with a letter "N" on it.

Connect the brown (or black)

phase cable to the terminal

which has a letter "L". Keep the

phase cable connected at all

times.

Connection cable

To replace the connection cable use only

the special cable or its equivalent. The

cable type is: H03V2V2-F T90.

Make sure that the cable section is

applicable to the voltage and the working

temperature. The yellow / green earth wire

must be approximately 2 cm longer than

the brown (or black) phase wire.

Assembly

min.

55 mm

min.

650 mm

560 mm

480 mm

min.

100 mm

30 mm

A. Supplied seal

B. Supplied bracket

CAUTION! Install the appliance

only on a worktop with flat

surface.

Possibilities for insertion

The panel installed below the hob must be

easy to remove and let an easy access in

case a technical assistance intervention is

necessary.

Kitchen unit with door

min 20 mm

(max 150 mm)

30 mm

60 mm

A. Removable panel

B. Space for connections

Kitchen unit with oven

The electrical connection of the hob and

the oven must be installed separately for

safety reasons and to let easy remove

oven from the unit.

PRODUCT DESCRIPTION

Cooking surface layout

Semi-rapid burner

Multi Crown burner

Auxiliary burner

Control knobs

Control knob

Symbol Description

no gas supply / off posi‐

tion

Symbol Description

ignition position / maxi‐

mum gas supply

minimum gas supply

DAILY USE

WARNING! Refer to Safety

chapters.

Burner overview

A. Burner cap

B. Burner crown

C. Ignition candle

D. Thermocouple

Ignition of the burner

Always light the burner before

you put on the cookware.

WARNING! Be very careful

when you use open fire in the

kitchen environment. The

manufacturer declines any

responsibility in case of the

flame misuse.

1. Push the control knob down and turn it

counterclockwise to the maximum gas

supply position ( ).

2. Keep the control knob pushed for

equal or less than 10 seconds. This

lets the thermocouple warm up. If not,

the gas supply is interrupted.

3. Adjust the flame after it is regular.

If after some tries the burner

does not light, check if the

crown and its cap are in correct

positions.

WARNING! Do not keep the

control knob pushed for more

than 15 seconds. If the burner

does not light after 15 seconds,

release the control knob, turn it

into off position and try to light

the burner again after minimum

1 minute.

CAUTION! In the absence of

electricity you can ignite the

burner without electrical device;

in this case approach the

burner with a flame, turn the

control knob counter-clockwise

to maximum gas supply

position and push it down.

Keep the control knob pushed

for equal or less than 10

seconds to let the

thermocouple warm up.

If the burner accidentally goes

out, turn the control knob to the

off position and try to light the

burner again after minimum 1

minute.

The spark generator can start

automatically when you switch

on the mains, after installation

or a power cut. It is normal.

The hob is supplied with the

progressive valves. They make

the flame regulation more

precise.

Turning the burner off

To put the flame out, turn the knob to the

off position .

WARNING! Always turn the

flame down or switch it off

before you remove the pans

from the burner.

HINTS AND TIPS

WARNING! Refer to Safety

chapters.

Cookware

CAUTION! Do not use cast

iron pans, clay or earthenware

pots, grill or toaster plates. The

stainless steel can become

tarnished if it is too much

heated.

WARNING! Do not put the

same pan on two burners.

WARNING! Do not put

unstable or damaged pots on

the burner to prevent spills and

injuries.

CAUTION! Make sure that the

bottoms of pots do not stand

too close to the control knob,

otherwise the flame heats the

control knob up.

CAUTION! Make sure that pot

handles are not above the front

edge of the cooktop.

CAUTION! Make sure that the

pots are placed centrally on the

burner in order to get the

maximum stability and a lower

gas consumption.

Energy saving

• If it is possible, always put the lids on

the cookware.

• When the liquid starts to boil, turn down

the flame to barely simmer the liquid.

Diameters of cookware

Use cookware with diameters

applicable to the size of

burners.

Burner Diameter of

cookware

(mm)

Multi Crown 180 - 260

Semi-rapid 120 - 240

Auxiliary 80 - 180

CARE AND CLEANING

WARNING! Refer to Safety

chapters.

General information

• Clean the hob after each use.

• Always use cookware with a clean

base.

• Scratches or dark stains on the surface

have no effect on how the hob

operates.

• Use a special cleaner suitable for the

surface of the hob.

Stainless steel

• Wash stainless steel parts with water,

and then dry them with a soft cloth.

• To remove burnt food, fat and stubborn

stains let them soak in a small amount

of mild detergent for a few minutes

before cleaning.

• Use cleaning products designed

specifically for cleaning stainless steel

in order to protect the steel surfaces.

• Do not use cleaning products

containing corrosive chemicals such as

chlorides, do not clean the surface with

disinfectants, stain or rust removers

and immersion cleaners.

Pan supports

The pan supports are not

resistant to washing in a

dishwasher. They must be

washed by hand.

1. Remove the pan supports to easily

clean the hob.

Be very careful when you

replace the pan supports to

prevent the hob top from

damage.

2. The enamel coating occasionally can

have rough edges, so be careful when

you wash the pan supports by hand

and dry them. If necessary, remove

stubborn stains with a paste cleaner.

3. After you clean the pan supports,

make sure that they are in correct

positions.

4. For the burner to operate correctly,

make sure that the arms of the pan

supports are aligned with the centre of

the burner.

Cleaning the hob

• Remove immediately: melted plastic,

plastic foil, sugar and food with sugar,

otherwise, the dirt can cause damage

to the hob. Take care to avoid burns.

• Remove when the hob is sufficiently

cool: limescale rings, water rings, fat

stains, shiny metallic discoloration.

Clean the hob with a moist cloth and a

non-abrasive detergent. After cleaning,

wipe the hob dry with a soft cloth.

• To clean the enamelled parts, caps and

crowns, wash them with warm soapy

water and dry them carefully before you

put them back on.

Cleaning the spark plug

This feature is obtained through a ceramic

ignition candle with a metal electrode.

Keep these components well clean to

prevent difficult lighting and check that the

burner crown holes are not obstructed.

Periodic maintenance

Speak to your local Authorised Service

Centre periodically to check the conditions

of the gas supply pipe and the pressure

adjuster, if fitted.

TROUBLESHOOTING

WARNING! Refer to Safety

chapters.

What to do if...

Problem Possible cause Remedy

There is no spark when you

try to activate the spark gen‐

erator.

The hob is not connected to

an electrical supply or it is

connected incorrectly.

Check if the hob is correctly

connected to the electrical

supply.

The fuse is blown. Make sure that the fuse is

the cause of the malfunc‐

tion. If the fuse is blown

again and again, contact a

qualified electrician.

Burner cap and crown are

placed incorrectly.

Place the burner cap and

crown correctly.

The flame extinguishes im‐

mediately after ignition.

Thermocouple is not heated

up sufficiently.

After lightning the flame,

keep the knob pushed for

equal or less than 10 sec‐

onds.

The flame ring is uneven. Burner crown is blocked with

food residues.

Make sure that the injector

is not blocked and the burn‐

er crown is clean.

If you cannot find a solution...

If you cannot find a solution to the problem

yourself, contact your dealer or an

Authorised Service Centre. Give the data

from the rating plate. Make sure, you

operated the hob correctly. If not the

servicing by a service technician or dealer

will not be free of charge, also during the

warranty period. The instructions about

the Service Centre and conditions of

guarantee are in the guarantee booklet.

Labels supplied with the

accessories bag

Stick the adhesive labels as indicated

below:

MOD.

PROD.NO.

SER.NO

DATA

MOD.

PROD.NO.

SER.NO

DATA

MOD.

PROD.NO.

SER.NO.

03 IT

MADE IN ITALY

TYPE

IP20

0049

A B C

A. Stick it on Guarantee Card and send

this part (if applicable).

B. Stick it on Guarantee Card and keep

this part (if applicable).

C. Stick it on instruction booklet.

TECHNICAL DATA

Hob dimensions

Width 595 mm

Depth 510 mm

Bypass diameters

BURNER Ø BYPASS 1/100 mm

Multi Crown 57

Semi-rapid 35

Auxiliary 28

Other technical data

TOTAL POW‐

ER:

Gas original:

G30/G31 (3B/P) 30/30

mbar

629 g/h

Gas replace‐

ment:

G20 (2H) 20 mbar 8,7 kW

Electric supply: 220-240 V ~ 50-60 Hz

Appliance cate‐

gory:

II2H3B/P

Gas connec‐

tion:

G 1/2"

Appliance

class:

Gas burners for LPG G30/G31 30/30 mbar

BURNER NORMAL

POWER kW

MINIMUM

POWER kW

INJECTOR

MARK

NOMINAL GAS

FLOW g/h

Multi Crown 3,65 1,4 095 265

Semi-rapid 2,0 0,6 71 145

Auxiliary 1,0 0,33 50 73

Gas burners for NATURAL GAS G20 20 mbar

BURNER NORMAL POWER

MINIMUM POWER

INJECTOR MARK

Multi Crown 4,0 1,4 146

Semi-rapid 1,85 0,6 92

Auxiliary 1,0 0,33 70

ENVIRONMENTAL CONCERNS

Recycle materials with the symbol . Put

the packaging in relevant containers to

recycle it. Help protect the environment

and human health by recycling waste of

electrical and electronic appliances. Do

not dispose of appliances marked with the

symbol with the household waste.

Return the product to your local recycling

facility or contact your municipal office.

TABLE DES MATIÈRES

Informations de sécurité 17

Consignes de sécurité 19

Installation 22

Description de l'appareil 26

Utilisation quotidienne 27

Conseils 28

Entretien et nettoyage 29

Dépannage 30

Caractéristiques techniques 32

Sous réserve de modifications.

INFORMATIONS DE SÉCURITÉ

Avant d'installer et d'utiliser cet appareil, lisez

soigneusement les instructions fournies. Le fabricant ne

pourra être tenu pour responsable des blessures et dégâts

résultant d'une mauvaise installation ou utilisation.

Conservez toujours les instructions dans un lieu sûr et

accessible pour vous y référer ultérieurement.

Sécurité des enfants et des personnes vulnérables

• Cet appareil peut être utilisé par des enfants de plus de

8 ans, ainsi que des personnes dont les capacités

physiques, sensorielles et mentales sont réduites ou dont

les connaissances et l'expérience sont insuffisantes, à

condition d'être surveillés ou d'avoir reçu des instructions

concernant l'utilisation sécurisée de l'appareil et de

comprendre les risques encourus.

• Les enfants entre 3 et 8 ans et les personnes ayant un

handicap très important et complexe doivent être tenus à

l'écart de l'appareil, à moins d'être surveillés en

permanence.

• Les enfants de moins de 3 ans doivent être tenus à l'écart

de l'appareil, à moins d'être surveillés en permanence.

• Ne laissez pas les enfants jouer avec l'appareil.

• Ne laissez pas les emballages à la portée des enfants et

jetez-les convenablement.

• Tenez les enfants et les animaux éloignés de l'appareil

lorsqu'il est en cours de fonctionnement ou lorsqu'il

refroidit. Les parties accessibles peuvent devenir chaudes

en cours d'utilisation.

• Si l'appareil est équipé d'un dispositif de sécurité enfants,

nous vous recommandons de l'activer.

• Les enfants ne doivent pas nettoyer ni entreprendre une

opération de maintenance sur l'appareil sans surveillance.

Sécurité générale

• AVERTISSEMENT : L'appareil et ses parties accessibles

deviennent chauds pendant son fonctionnement. Veillez à

ne pas toucher les éléments chauffants.

• AVERTISSEMENT : Il peut être dangereux de laisser

chauffer de la graisse ou de l'huile sans surveillance sur

une table de cuisson car cela pourrait provoquer un

incendie.

• N'essayez JAMAIS d'éteindre un feu avec de l'eau.

Éteignez l'appareil puis couvrez les flammes, par exemple

avec un couvercle ou une couverture ignifuge.

• ATTENTION : L'appareil ne doit pas être branché à

l'alimentation en utilisant un appareil de connexion externe

comme un minuteur, ou branché à un circuit qui est

régulièrement activé/désactivé par un fournisseur

d'énergie.

• ATTENTION : Toute cuisson doit être surveillée. Une

cuisson courte doit être surveillée en permanence.

• AVERTISSEMENT : Risque d'incendie ! N'entreposez rien

sur les surfaces de cuisson.

• Ne posez pas d'objets métalliques tels que couteaux,

fourchettes, cuillères ou couvercles sur la table de cuisson

car ils pourraient chauffer.

• N'utilisez pas l'appareil avant de l'avoir installé dans la

structure encastrée.

• N'utilisez pas de nettoyeur vapeur pour nettoyer l'appareil.

• Si le câble d'alimentation est endommagé, il doit être

remplacé par le fabricant, un service de maintenance

agréé ou un technicien qualifié afin d'éviter tout danger.

• Si l'appareil est relié directement à l'alimentation

électrique, installez un sectionneur avec une ouverture de

contact. Il est indispensable de garantir une déconnexion

complète conformément aux conditions de surtension de

catégorie III. Le fil de terre n'est pas concerné.

• Lorsque vous acheminez le câble d'alimentation, assurez-

vous qu'il n'entre pas en contact direct (par exemple, à

l'aide d'un manchon isolant) avec des parties pouvant

atteindre des températures supérieures de 50 °C à la

température ambiante.

• AVERTISSEMENT : Utilisez uniquement les dispositifs de

protection pour table de cuisson conçus ou indiqués

comme adaptés par le fabricant de l'appareil de cuisson

dans les instructions d'utilisation, ou les dispositifs de

protection pour table de cuisson intégrés à l'appareil.

L'utilisation de dispositifs de protection non adaptés peut

entraîner des accidents.

CONSIGNES DE SÉCURITÉ

Cet appareil est adapté aux marchés

suivants: DZ MA

Installation

AVERTISSEMENT! L'appareil

doit être installé uniquement

par un professionnel qualifié.

AVERTISSEMENT! Risque de

blessure corporelle ou de

dommages matériels.

• Retirez l'intégralité de l'emballage.

• N'installez pas et ne branchez pas un

appareil endommagé.

• Suivez scrupuleusement les

instructions d'installation fournies avec

l'appareil.

• Respectez l'espacement minimal requis

par rapport aux autres appareils et

éléments.

• Soyez toujours vigilants lorsque vous

déplacez l'appareil car il est lourd.

Utilisez toujours des gants de sécurité

et des chaussures fermées.

• Isolez les surfaces découpées à l'aide

d'un matériau d'étanchéité pour éviter

que la moisissure ne provoque de

gonflements.

• Protégez la partie inférieure de

l'appareil de la vapeur et de l'humidité.

• N'installez pas l'appareil près d'une

porte ou sous une fenêtre. Les

récipients chauds risqueraient de

tomber de l'appareil lors de l'ouverture

de celles-ci.

• Si l'appareil est installé au-dessus de

tiroirs, assurez-vous qu'il y a

suffisamment d'espace entre le fond de

l'appareil et le tiroir supérieur pour que

l'air puisse circuler.

• Le dessous de l'appareil peut devenir

très chaud. Veillez à installer un

panneau de séparation ignifuge sous

l'appareil pour en bloquer l'accès.

Branchement électrique

AVERTISSEMENT! Risque

d'incendie ou d'électrocution.

• L’ensemble des branchements

électriques doit être effectué par un

technicien qualifié.

• L’appareil doit être relié à la terre.

• Avant toute intervention, assurez-vous

que l'appareil est débranché.

• Vérifiez que les paramètres figurant sur

la plaque signalétique correspondent

aux données électriques de votre

réseau.

• Assurez-vous que l'appareil est bien

installé. Un câble d'alimentation lâche

et inapproprié ou une fiche (si

présente) non serrée peuvent être à

l'origine d'une surchauffe des bornes.

• Utilisez le câble d'alimentation

électrique approprié.

• Ne laissez pas le câble d'alimentation

s'emmêler.

• Assurez-vous qu'une protection anti-

électrocution est installée.

• Utilisez un collier anti-traction sur le

câble.

• Assurez-vous que le câble

d'alimentation ou la fiche (si présente)

n'entrent pas en contact avec les

surfaces brûlantes de l'appareil ou les

récipients brûlants lorsque vous

branchez l'appareil à des prises

électriques situées à proximité.

• L’appareil ne doit pas être raccordé à

l’aide d'une prise multiple ou d'un

prolongateur.

• Veillez à ne pas endommager la fiche

secteur (si présente) ni le câble

d'alimentation. Contactez notre service

après-vente agréé ou un électricien

pour remplacer le câble d'alimentation

s'il est endommagé.

• La protection contre les chocs des

parties sous tension et isolées doit être

fixée de telle manière qu’elle ne puisse

pas être enlevée sans outils.

• Ne branchez la fiche d’alimentation à la

prise de courant qu’à la fin de

l’installation. Assurez-vous que la prise

principale est accessible une fois

l’appareil installé.

• Si la prise de courant est lâche, ne

branchez pas la fiche d'alimentation

secteur.

• Ne tirez jamais sur le câble

d’alimentation électrique pour

débrancher l’appareil. Tirez toujours

sur la fiche de la prise secteur.

• N’utiliser que des dispositifs d’isolation

corrects : coupe-circuits de protection

de ligne, fusibles. (les fusibles à visser

doivent être retirés du support), un

disjoncteur différentiel et des

contacteurs.

• L'installation électrique doit être

équipée d'un dispositif d'isolement à

coupure omnipolaire. Le dispositif

d'isolement doit présenter une distance

d'ouverture des contacts d'au moins

3 mm.

Raccordement au gaz

• Tous les raccordements au gaz doivent

être effectués par une personne

qualifiée.

• Avant l'installation, vérifiez que les

conditions de distribution locales

(nature et pression du gaz) sont

compatibles avec le réglage de

l'appareil.

• Assurez-vous que l'air circule autour de

l'appareil.

• Les informations concernant

l'alimentation en gaz se trouvent sur la

plaque signalétique.

• Cet appareil n'est pas raccordé à un

dispositif d'évacuation des produits de

combustion. Assurez-vous de brancher

l'appareil selon les réglementations

d'installation en vigueur. Respectez les

recommandations pour assurer une

bonne ventilation.

Utilisation

AVERTISSEMENT! Risque de

blessures, de brûlures ou

d'électrocution.

• Avant la première utilisation, retirez les

emballages, les étiquettes et les films

de protection (si présents).

• Cet appareil est exclusivement destiné

à une utilisation domestique.

• Ne modifiez pas les caractéristiques de

cet appareil.

• Assurez-vous que les orifices de

ventilation ne sont pas bouchés.

• Ne laissez jamais l'appareil sans

surveillance pendant son

fonctionnement.

La page charge ...

Arthur_Martin AGS6435X Manuel utilisateur

Marque: Arthur_Martin

Modèle: AGS6435X

Catégorie: Plaques de cuisson

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Arthur_Martin AGS6435X User manual