Kenmore 106.5035 Series Manuel utilisateur
- Catégorie
- Frigos
- Taper
- Manuel utilisateur
Use & Care Guide
Manual de uso y cuidado
Guide d’utilisation et d’entretien
English / Español / Français
Models/Modelos/Modèles: 106.5022*, 106.5023*, 106.5027*, 106.5028*, 106.5034*, 106.5035*
Kenmore®
Side by Side Refrigerator
Refrigerador de dos puertas
Réfrigérateur côte à côte
* = color number, número de color, le numéro de la couleur
P/N W10319293A
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A.
www.kenmore.com
www.sears.com
Sears Canada Inc.
Toronto, Ontario, Canada M5B 2B8
www.sears.ca
2
TABLE OF CONTENTS
WARRANTY.................................................................................. 4
REFRIGERATOR SAFETY ...............................................................5
Proper Disposal of Your Old Refrigerator......................................... 5
INSTALLATION INSTRUCTIONS .................................................. 6
Unpack the Refrigerator ....................................................................... 6
Location Requirements........................................................................... 6
Electrical Requirements .........................................................................7
Water Supply Requirements ................................................................7
Base Grille................................................................................................7
Refrigerator Doors.................................................................................. 8
Adjust the Doors.....................................................................................10
Connect the Water Supply..................................................................10
Prepare the Water System...................................................................11
Normal Sounds.......................................................................................12
REFRIGERATOR USE ................................................................... 12
Ensuring Proper Air Circulation...........................................................12
Using the Controls .................................................................................12
Convertible Drawer Temperature Control........................................13
Crisper Humidity Control......................................................................13
Chilled Door Bin.....................................................................................13
Water and Ice Dispensers ...................................................................13
Water Filter Status Light......................................................................15
Water Filtration System.......................................................................15
Ice Maker and Storage Bin..................................................................16
REFRIGERATOR FEATURES..........................................................17
Refrigerator Shelves .............................................................................17
Deli Bin.................................................................................................... 17
Convertible Vegetable/Meat Drawer, Crisper and Covers .........17
Wine Rack..............................................................................................17
Utility Bin................................................................................................. 17
FREEZER FEATURES.....................................................................18
Freezer Shelf.......................................................................................... 18
Freezer Basket or Bin............................................................................ 18
DOOR FEATURES.........................................................................18
Door Rails or Bins.................................................................................. 18
Door Bins................................................................................................. 19
REFRIGERATOR CARE.................................................................19
Cleaning.................................................................................................. 19
Changing the Light Bulbs.....................................................................20
Power Interruptions...............................................................................20
Vacation and Moving Care................................................................20
TROUBLESHOOTING...................................................................21
Refrigerator Operation.........................................................................21
Temperature and Moisture..................................................................22
Ice and Water.......................................................................................22
PROTECTION AGREEMENTS......................................................24
ACCESSORIES.............................................................................24
WATER FILTER CERTIFICATIONS ...............................................24
PERFORMANCE DATA SHEET .................................................... 25
SERVICE NUMBERS ..................................................BACK COVER
ÍNDICE
GARANTÍA................................................................................. 27
SEGURIDAD DEL REFRIGERADOR ..............................................28
Cómo deshacerse adecuadamente de su refrigerador viejo.......28
INSTRUCCIONES DE INSTALACIÓN.......................................... 29
Desempaque el refrigerador..............................................................29
Requisitos de ubicación.......................................................................29
Requisitos eléctricos .............................................................................30
Requisitos del suministro de agua .....................................................30
Rejilla de la base..................................................................................30
Puertas del refrigerador.......................................................................31
Ajuste las puertas..................................................................................33
Conexión del suministro de agua...................................................... 33
Preparación del sistema de agua......................................................35
Sonidos normales..................................................................................35
USO DE SU REFRIGERADOR ...................................................... 36
Cómo asegurar la debida circulación del aire...............................36
Uso de los controles.............................................................................36
Control de temperatura del cajón convertible ...............................37
Control de humedad del cajón para verduras...............................37
Depósito enfriador de la puerta........................................................37
Despachadores de agua y hielo........................................................37
Luz de estado del filtro de agua.......................................................38
Sistema de filtración de agua............................................................39
Fábrica de hielo y depósito................................................................40
CARACTERÍSTICAS DEL REFRIGERADOR ...................................41
Estantes del refrigerador......................................................................41
Recipiente para carnes frías............................................................... 41
Cajón convertible para verduras/carne,
cajón para verduras y tapas.............................................................. 41
Portabotellas..........................................................................................42
Recipiente de uso general...................................................................42
CARACTERÍSTICAS DEL CONGELADOR.....................................42
Estante del congelador........................................................................42
Canastilla o recipiente del congelador ............................................42
CARACTERÍSTICAS DE LA PUERTA ............................................43
Rieles o recipientes de la puerta........................................................43
Recipientes de la puerta......................................................................43
CUIDADO DE SU REFRIGERADOR .............................................43
Limpieza .................................................................................................43
Cómo cambiar los focos .................................................................... 44
Cortes de corriente...............................................................................45
Cuidado durante las vacaciones y mudanzas................................45
SOLUCIÓN DE PROBLEMAS .......................................................46
Funcionamiento del refrigerador...................................................... 46
Temperatura y humedad.................................................................... 47
Hielo y agua ......................................................................................... 47
CONTRATOS DE PROTECCIÓN..................................................49
ACCESORIOS..............................................................................49
HOJA DE DATOS DEL RENDIMIENTO........................................ 50
NÚMEROS DE SERVICIO .................................CONTRAPORTADA
3
TABLE DES MATIÈRES
GARANTIE .................................................................................. 51
SÉCURITÉ DU RÉFRIGÉRATEUR...................................................52
Mise au rebut de votre vieux réfrigérateur .....................................52
INSTRUCTIONS D’INSTALLATION..............................................53
Déballage du réfrigérateur ................................................................53
Exigences d'emplacement .................................................................. 53
Spécifications électriques....................................................................54
Spécifications de l’alimentation en eau...........................................54
Grille de la base...................................................................................54
Portes du réfrigérateur.........................................................................55
Ajustement des portes..........................................................................57
Raccordement de la canalisation d'eau ..........................................57
Préparer le système d'eau...................................................................59
Sons normaux........................................................................................59
UTILISATION DU RÉFRIGÉRATEUR............................................ 60
Pour s’assurer d’une circulation d’air appropriée...........................60
Utilisation des commandes.................................................................60
Commande de température du tiroir convertible ...........................61
Réglage de l'humidité dans le bac à légumes.................................61
Compartiment froid de la porte.........................................................61
Distributeurs d’eau et de glaçons.......................................................61
Témoin lumineux de l’état du filtre à eau........................................62
Système de filtration d’eau.................................................................63
Machine à glaçons et bac d'entreposage.......................................64
CARACTÉRISTIQUES DU RÉFRIGÉRATEUR................................. 65
Tablettes du réfrigérateur ...................................................................65
Bac pour spécialités alimentaires ......................................................65
Tiroir à légumes/viande convertible,
bac à légumes et couvercles ..............................................................65
Casier à vin ............................................................................................66
Casier utilitaire ......................................................................................66
CARACTÉRISTIQUES DU CONGÉLATEUR ..................................66
Tablette de congélateur......................................................................66
Panier ou bac de congélateur............................................................66
CARACTÉRISTIQUES DE LA PORTE ............................................67
Tringles de la porte ou balconnets................................................... 67
Balconnets de porte............................................................................. 67
ENTRETIEN DU RÉFRIGÉRATEUR ...............................................67
Nettoyage ............................................................................................. 67
Remplacement des ampoules d’éclairage.......................................68
Pannes de courant ................................................................................69
Entretien avant les vacances ou lors d’un déménagement...........69
DÉPANNAGE..............................................................................70
Fonctionnement du réfrigérateur ...................................................... 70
Température et humidité .....................................................................71
Glaçons et eau......................................................................................71
CONTRATS DE PROTECTION.....................................................74
ACCESSOIRES.............................................................................74
FEUILLE DE DONNÉES SUR LA PERFORMANCE......................... 75
NUMÉROS DE SERVICE ............................ COUVERTURE ARRIÈRE
4
KENMORE APPLIANCE WARRANTY
ONE YEAR LIMITED WARRANTY
When installed, operated and maintained according to all
instructions supplied with the product, if this appliance fails due to
a defect in material or workmanship within one year from the date
of purchase, call 1!800!4!MY!HOME
®
to arrange for free repair.
This warranty applies for only 90 days from the date of purchase if
this appliance is ever used for other than private family purposes.
THIS WARRANTY COVERS ONLY DEFECTS IN MATERIAL AND
WORKMANSHIP. SEARS WILL NOT PAY FOR:
1. Expendable items that can wear out from normal use, including
but not limited to filters, belts, light bulbs, and bags.
2. A service technician to instruct the user in correct product
installation, operation or maintenance.
3. A service technician to clean or maintain this product.
4. Damage to or failure of this product if it is not installed,
operated or maintained according to all instructions supplied
with the product.
5. Damage to or failure of this product resulting from accident,
abuse, misuse or use for other than its intended purpose.
6. Damage to or failure of this product caused by the use of
detergents, cleaners, chemicals or utensils other than those
recommended in all instructions supplied with the product.
7. Damage to or failure of parts or systems resulting from
unauthorized modifications made to this product.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF
REMEDIES
Customer’s sole and exclusive remedy under this limited warranty
shall be product repair as provided herein. Implied warranties,
including warranties of merchantability or fitness for a particular
purpose, are limited to one year or the shortest period allowed by
law. Sears shall not be liable for incidental or consequential
damages. Some states and provinces do not allow the exclusion or
limitation of incidental or consequential damages, or limitations on
the duration of implied warranties of merchantability or fitness, so
these exclusions or limitations may not apply to you.
This warranty applies only while this appliance is used in the United
States or Canada.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
Sears Brands Management Corporation
Hoffman Estates, IL 60179
Sears Canada Inc.
Toronto, Ontario, Canada M5B 2C3
PRODUCT RECORD
Record your complete model number, serial number, and purchase
date. You can find this information on the model and serial number
label located on the product.
Have this information available to help you obtain assistance or
service more quickly whenever you contact Sears concerning your
appliance.
Model number __ __ __._____________________________________
Serial number _____________________________________________
Purchase date _____________________________________________
Save these instructions and your sales receipt for future reference.
5
REFRIGERATOR SAFETY
Proper Disposal of Your Old Refrigerator
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous –
even if they will sit for “just a few days.” If you are getting rid of
your old refrigerator, please follow these instructions to help
prevent accidents.
Before You Throw Away Your Old Refrigerator or Freezer:
■ Take off the doors.
■ Leave the shelves in place so that children may not easily climb
inside.
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
SAVE THESE INSTRUCTIONS
■
Plug into a grounded 3 prong outlet.
■
Do not remove ground prong.
■
Do not use an adapter.
■
Do not use an extension cord.
■
Disconnect power before servicing.
■
Replace all parts and panels before operating.
■
Remove doors from your old refrigerator.
■
Use nonflammable cleaner.
■
Keep flammable materials and vapors, such as gasoline,
away from refrigerator.
■
Use two or more people to move and install refrigerator.
■
Disconnect power before installing ice maker (on ice maker
kit ready models only).
■
Use a sturdy glass when dispensing ice (on some models).
■
Do not hit the refrigerator glass doors (on some models).
WARNING
Suffocation Hazard
Remove doors from your old refrigerator.
Failure to do so can result in death or brain damage.
6
INSTALLATION INSTRUCTIONS
Unpack the Refrigerator
Remove the Packaging
■ Remove tape and glue residue from surfaces before turning on
the refrigerator. Rub a small amount of liquid dish soap over
the adhesive with your fingers. Wipe with warm water and dry.
■ Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For more
information see “Refrigerator Safety.”
Clean Before Using
After you remove all of the packaging materials, clean the inside of
your refrigerator before using it. See the cleaning instructions in
“Refrigerator Care.”
Location Requirements
To ensure proper ventilation for your refrigerator, allow for ¹⁄₂"
(1.25 cm) of space on each side and at the top. Allow for 1"
(2.54 cm) of space behind the refrigerator. If your refrigerator has
an ice maker, allow extra space at the back for the water line
connections. When installing your refrigerator next to a fixed wall,
leave a 2" (5.08 cm) minimum space on each side (depending on
your model) to allow the doors to swing open.
NOTES:
■ It is recommended that you do not install the refrigerator near
an oven, radiator, or other heat source. Do not install in a
location where the temperature will fall below 55°F (13°C).
■ Normal minimum cabinet cut-out width required for product
installation is 36" (91.44 cm). However, if the product is placed
against an extended wall and the ability to remove the crisper
pans is desired, an additional 18" (45.72 cm) of cabinet width
is required, so a total cabinet opening width of 54" (137.16 cm)
is recommended.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for
cleaning or service, be sure to cover the floor with
cardboard or hardboard to avoid floor damage. Always pull
the refrigerator straight out when moving it. Do not wiggle or
“walk” the refrigerator when trying to move it, as floor
damage could occur.
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
1
/
2
" (1.25 cm)
2" (5.08 cm)
7
Electrical Requirements
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical connection.
Recommended Grounding Method
A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet that
cannot be turned off by a switch. Do not use an extension cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn the control (Thermostat, Refrigerator or
Freezer Control depending on the model) OFF and then disconnect
the refrigerator from the electrical source. When you are finished,
reconnect the refrigerator to the electrical source and reset the
control (Thermostat, Refrigerator or Freezer Control depending on
the model) to the desired setting. See “Using the Control(s).”
Water Supply Requirements
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed here.
TOOLS NEEDED:
NOTE: Your refrigerator dealer has a kit available with a
¹⁄₄"
(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.
Before purchasing, make sure a saddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or
³⁄₁₆"
(4.76 mm) saddle valve which reduces water flow and clogs more
easily.
IMPORTANT:
■ All installations must meet local plumbing code requirements.
■ Use copper tubing and check for leaks. Install copper tubing
only in areas where the household temperatures will remain
above freezing.
Water Pressure
A cold water supply with water pressure of between 30 and 120 psi
(207 and 827 kPa) is required to operate the water dispenser and
ice maker. If you have questions about your water pressure, call a
licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 and
827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis system
needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than 40 to
60 psi (276 to 414 kPa):
■ Check to see whether the sediment filter in the reverse osmosis
system is blocked. Replace the filter if necessary.
■ Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
■ If your refrigerator has a water filter, it may further reduce the
water pressure when used in conjunction with a reverse osmosis
system. Remove the water filter. See “Water Filtration System.”
If you have questions about your water pressure, call a licensed,
qualified plumber.
Base Grille
Remove the Base Grille:
1. Open both doors.
2. Place hands along the ends of the grille. Push in on the top of
the base grille and pull up on the bottom.
NOTE: Be sure to refasten the Tech Sheet behind the base grille
after cleaning.
Replace the Base Grille:
1. Open both doors.
2. Line up the grille support tabs with the metal clips.
3. Push the grille firmly to snap it into place.
■ Flat-blade screwdriver
■ ⁷⁄₁₆" (11.11 mm) and ¹⁄₂" (12.7 mm)
open-end or two adjustable
wrenches
■ ¹⁄₄" (6.35 mm) nut
driver
■ ¹⁄₄" (6.35 mm) drill bit
■ Cordless drill
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
8
Refrigerator Doors
TOOLS NEEDED: ¹⁄₄" hex-head socket wrench, ⁵⁄₁₆" hex-head socket wrench and a flat-blade screwdriver.
IMPORTANT: Before you begin, turn the refrigerator control OFF. Unplug refrigerator or disconnect power. Remove food and any adjustable
door or utility bins from doors.
NOTE: It may only be necessary to remove either the door handle or the doors to get your product through the doorway of your home.
Measure the doorway to see whether you need to remove the refrigerator handles or the doors.
WARNING
Electrical Shock Hazard
Disconnect power before removing doors.
Reconnect both ground wires before operating.
Failure to do so can result in death or electrical shock.
5
Door Removal
2
Base Grille
4
Top Left Hinge
A. Do Not Remove Screw
A
1
Handle
Removal
(Optional)
Bottom Hinge
7
A. Do Not
Remove Screw
A
3
Water Dispenser
Tubing Connection
A. Red Outer Ring
A
6
A. Do Not Remove Screw
A
Top Right Hinge
9
Door Alignment
8
Level
Door Closing and Alignment
Front Leveling
10
A. Leveling Screw
A
9
Remove the Handles (optional)
1. Apply firm pressure with your hand on the face of trim. Slide
top trim up and bottom trim down away from handle. Lift trim
pieces off shoulder screws. See Graphic 1.
2. Remove handle screws and handles. See Graphic 1.
3. Move refrigerator into place. Replace handles as shown. See
Graphic 1.
Remove the Doors
1. Unplug refrigerator or disconnect power.
2. Open both refrigerator doors. Remove the base grille. Place
hands along the ends of the grille. Push in on the top of the
base grille and pull up on the bottom. See Graphic 2.
3. Close both doors and keep them closed until you are ready to
lift them free from the cabinet.
4. If you have a dispenser (ice or water), disconnect the water
dispenser tubing located behind the base grille on the freezer
door side. See Graphic 3.
■ Press the red outer ring against the face of the fitting and
pull the dispenser tubing free.
■ On some models, remove the tubing from hose clip.
5. Remove the top left hinge cover and screws as shown. See
Graphic 4. Do not remove screw A.
6. Disconnect wiring:
■ Disconnect wiring plug.
■ Remove green ground wire screw to disconnect ground
wires.
7. Lift freezer door straight up and off of the bottom hinge. See
Graphic 5. The water dispenser tubing remains attached to the
freezer door and pulls through the bottom left hinge. Be sure to
avoid damaging the dispenser tubing.
8. Remove the top right hinge cover and screws as shown. See
Graphic 6. Do not remove screw A.
9. Lift the refrigerator door straight up and off of the bottom
hinge.
10. It may not be necessary to remove the bottom hinge to move
the refrigerator through a doorway. Both bottom hinges have
similar construction.
■ Remove the hinges as shown. See Graphic 7. Do not
remove screw A.
Replace the Doors and Hinges
1. Replace both bottom hinges, if removed. Tighten screws.
2. Feed the dispenser tubing through the bottom left hinge before
replacing the freezer door on the hinge. Assistance may be
needed.
NOTE: Provide additional support for the doors while the top
hinges are being replaced. Do not depend on the door magnets
to hold the doors in place while you are working.
3. Reconnect water dispenser tubing by pushing tubing into fitting
until it stops and the red outer ring touches face of fitting. See
Graphic 3. On some models, replace tubing in hose clip.
4. Align and replace the top left hinge as shown. See Graphic 4.
Tighten screws.
■ Reconnect both ground wires.
■ Reconnect wiring plug.
5. Replace left hinge cover and screws.
6. Replace the refrigerator door by lifting the door onto the
bottom right hinge.
7. Align and replace the top right hinge as shown. See Graphic 6.
Tighten screws.
8. Replace hinge cover and screws. Tighten screws.
9. Plug in refrigerator or reconnect power.
A. Do not remove screw A.
B. Ground wires
C. Green ground wire screw
D. Wiring plug
WARNING
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.
B
A
C
D
A. Do not remove screw A.
B. Ground wires
C. Green ground wire screw
D. Wiring plug
WARNING
Electrical Shock Hazard
Reconnect both ground wires.
Failure to do so can result in death or electrical shock.
B
A
C
D
10
Adjust the Doors
Door Closing
1. Place a level inside the refrigerator at the back of the top shelf.
See Graphic 8 in “Refrigerator Doors.”
2. Locate the leveling screws behind the base grille of the
refrigerator on either side.
3. Use a hex-head wrench to adjust the front roller leveling screws
until the refrigerator is level. Turn the front roller leveling screw
to the right to raise that side of the refrigerator or turn the
leveling screw to the left to lower that side. See Graphic 10 in
“Refrigerator Doors.” Make sure refrigerator is level before
proceeding.
4. Check the door alignment after leveling the refrigerator.
Align the Doors
IMPORTANT: First level the back of the refrigerator as described in
“Door Closing.”
The doors may be uneven after leveling the refrigerator. See
Graphic 9 in “Refrigerator Doors.” The doors are preset at the
factory so that the refrigerator door is higher than the freezer door
by approximately the thickness of a quarter. Once the doors are
loaded with food, they should be even. If the door height needs to
be adjusted AFTER the doors have been loaded with food, follow
the these steps.
1. Use a hex-head wrench to adjust the front roller leveling screws
until the doors are even. Turn the front roller leveling screw to
the right to raise that side of the refrigerator or turn the leveling
screw to the left to lower that side. See Graphic 10 in
“Refrigerator Doors.”
NOTE: Open and close both the refrigerator and freezer doors
after each adjustment to check the door alignment.
2. Open the doors and replace the base grille. Line up the grille
support tabs with the metal clips. Push the grille firmly to snap it
into place.
NOTE: Be sure to refasten the Tech Sheet behind the base
grille.
Connect the Water Supply
Read all directions before you begin.
IMPORTANT: If you turn the refrigerator on before the water line is
connected, turn the ice maker OFF.
Connect to Water Line
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Locate a ½" to 1
¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water
pipe near the refrigerator.
IMPORTANT:
■ Make sure it is a cold water pipe.
■ Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and normal sediment from collecting in the valve.
4. Determine the length of copper tubing you need. Measure from
the connection on the lower left rear of refrigerator to the
water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use
¹⁄₄"
(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both
ends of copper tubing are cut square.
5. Using a cordless drill, drill a
¹⁄₄" (6.35 mm) hole in the cold
water pipe you have selected.
6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the
¹⁄₄" (6.35 mm)
drilled hole in the water pipe and that the washer is under the
pipe clamp. Tighten the packing nut. Tighten the pipe clamp
screws slowly and evenly so the washer makes a watertight
seal. Do not overtighten or you may crush the copper tubing.
7. Slip the compression sleeve and compression nut onto the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten.
8. Place the free end of the tubing in a container or sink, and turn
ON the main water supply. Flush the tubing until water is clear.
Turn OFF the shutoff valve on the water pipe. Coil the copper
tubing.
Connect to Refrigerator
Style 1 - Connection to Water Valve
1. Unplug refrigerator or disconnect power.
2. Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut. Do not
overtighten.
3. Use the tube clamp on the back of the refrigerator to secure
the tubing to the refrigerator as shown. This will help avoid
damage to the tubing when the refrigerator is pushed back
against the wall.
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any connections (including connections
at the valve) or nuts that leak.
6. The ice maker is equipped with a built-in water strainer. If your
water conditions require a second water strainer, install it in the
¹⁄₄" (6.35 mm) water line at either tube connection. Obtain a
water strainer from your nearest appliance dealer.
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
E. Compression sleeve
F. Shutoff valve
G. Packing nut
A. Tube clamp
B. Tube clamp screw
C. Copper tubing
D. Compression nut
E. Valve inlet
A
B
C
DEF
G
A
C
B
D
E
11
Style 2 - Connection to Water Line
1. Unplug refrigerator or disconnect power.
2. Remove and discard the black nylon plug from the gray water
tube on the rear of the refrigerator.
3. If the gray water tube supplied with the refrigerator is not long
enough, a
¹⁄₄" x ¹⁄₄" (6.35 mm x 6.35 mm) coupling is needed in
order to connect the water tubing to an existing household
water line. Thread the provided nut onto the coupling on the
end of the copper tubing.
NOTE: Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtighten.
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
Style 3 - Connection to Shutoff Valve
1. Unplug refrigerator or disconnect power.
2. Remove and discard the black nylon plug from the gray water
tube on the rear of the refrigerator.
3. Thread the provided nut onto the water valve as shown.
NOTE: Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtighten.
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
Complete the Installation
1. Plug into a grounded 3 prong outlet.
2. Flush the water system. See “Prepare the Water System.”
NOTE: It may take up to 24 hours for your ice maker to begin
producing ice.
Prepare the Water System
Please read before using the water system.
Immediately after installation, follow the steps below to make sure
that the water system is properly cleaned.
1. Open the freezer door and turn off the ice maker. For Style 1,
lift up the wire shutoff arm as shown. For Style 2, move the
switch to the OFF (right) setting as shown. The On/Off switch is
located on the top right side of the freezer compartment.
Style 1
Style 2
NOTE: If your model has a base grille filter system, make sure the
base grille filter is properly installed and the cartridge cap handle
is in the horizontal position.
A. Refrigerator water tubing
B. Nut (provided)
C. Bulb
D.Coupling (provided)
E. Ferrule (purchased)
F. N ut (purchased)
G. Household water line
A. Bulb
B. Nut (provided)
A B C D E F G
A
B
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
12
2. Flush the water system. Use a sturdy container to depress and
hold the water dispenser lever for 5 seconds, then release it for
5 seconds. Repeat until water begins to flow. Once water
begins to flow, continue depressing and releasing the dispenser
lever (5 seconds on, 5 seconds off) until a total of 3 gal. (12 L)
has been dispensed. This will flush air from the filter and water
dispensing system, and prepare the water filter for use.
Additional flushing may be required in some households. As air
is cleared from the system, water may spurt out of the
dispenser.
3. Open the freezer door and turn on the ice maker. For Style 1,
lower the wire shutoff arm. For Style 2, move the switch to the
ON (left) position. Please refer to the “Ice Maker and Storage
Bin” section for further instructions on the operation of your ice
maker.
■ Allow 24 hours to produce the first batch of ice.
■ Discard the first three batches of ice produced.
■ Depending on your model, you may want to select the
maximum ice feature to increase the production of ice.
Normal Sounds
Your new refrigerator may make sounds that your old one didn’t
make. Because the sounds are new to you, you might be concerned
about them. Most of the new sounds are normal. Hard surfaces,
such as the floor, walls, and cabinets, can make the sounds seem
louder. The following describes the kinds of sounds and what may
be making them.
■ If your refrigerator is equipped with an ice maker, you will hear
a buzzing sound when the water valve opens to fill the ice
maker for each cycle.
■ Your refrigerator is designed to run more efficiently to keep
your food items at the desired temperatures and to minimize
energy usage. The high efficiency compressor and fans may
cause your refrigerator to run longer than your old one. You
may also hear a pulsating or high-pitched sound from the
compressor or fans adjusting to optimize performance.
■ You may hear the evaporator fan motor circulating air through
the refrigerator and freezer compartments. The fan speed may
increase as you open the doors or add warm food.
■ Rattling noises may come from the flow of refrigerant, the
water line, or items stored on top of the refrigerator.
■ Water dripping on the defrost heater during a defrost cycle
may cause a sizzling sound.
■ As each cycle ends, you may hear a gurgling sound due to the
refrigerant flowing in your refrigerator.
■ Contraction and expansion of the inside walls may cause a
popping noise.
■ You may hear air being forced over the condenser by the
condenser fan.
■ You may hear water running into the drain pan during the
defrost cycle.
REFRIGERATOR USE
Ensuring Proper Air Circulation
In order to ensure proper temperatures, you need to permit air to
flow between the two sections. Cold air enters the bottom of the
freezer section and moves up. It then enters the refrigerator section
through the top vent. Air then returns to the freezer as shown.
Do not block any airflow vents. If the vents are blocked, airflow will
be obstructed and temperature and moisture problems may occur.
IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To avoid odor
transfer and drying out of food, wrap or cover foods tightly.
Using the Controls
For your convenience, your refrigerator controls are preset at the
factory. When you first install your refrigerator, make sure that the
controls are still preset. The Refrigerator Control and the Freezer
Control should both be set to the “mid-settings.”
Style 1: Rotary Controls
Style 2: Slide Controls
IMPORTANT:
■ Your product will not cool when the REFRIGERATOR Control is
set to OFF.
■ The Refrigerator Control adjusts the refrigerator compartment
temperature. The Freezer Control adjusts the freezer
compartment temperature. Settings to the left of the mid-
setting make the temperature less cold. Settings to the right of
the mid-setting make the temperature colder.
Refrigerator
off
colder
1
234
Freezer
cold
colder
1
234
13
■ Wait 24 hours before you put food into the refrigerator. If you
add food before the refrigerator has cooled completely, your
food may spoil.
NOTE: Adjusting the Refrigerator and Freezer Controls to a higher
(colder) than recommended setting will not cool the compartments
any faster.
Adjusting Controls
Give the refrigerator time to cool down completely before adding
food. It is best to wait 24 hours before you put food into the
refrigerator. The settings indicated in the previous section should be
correct for normal household refrigerator usage. The controls are
set correctly when milk or juice is as cold as you like and when ice
cream is firm.
Rotary Controls: Turn the control right (clockwise) to make the
compartment colder. Turn the control left (counterclockwise) to
make it less cold. To turn the cooling system off, turn the
Refrigerator Control counterclockwise until it reaches the OFF
position.
Slide Controls: Slide the control one setting to the right to make the
compartment colder. Slide the control one setting to the left to
make it less cold.
If you need to adjust temperatures in the refrigerator or freezer, use
the settings listed in the chart below as a guide. Wait at least
24 hours between adjustments.
Convertible Drawer Temperature Control
(on some models)
The control can be adjusted to properly chill meats or vegetables.
The air inside the pan is cooled to avoid “spot” freezing and can be
set to keep meats at the National Livestock and Meat Board
recommended storage temperatures of 28° to 32°F (-2° to 0°C).
The convertible vegetable/meat drawer control comes preset at
the lowest meat setting.
To store meat:
Set the control to one of the three MEAT settings to store meat at its
optimal storage temperature.
To store vegetables:
Set the control to VEG to store vegetables at their optimal storage
temperatures.
NOTE: If food starts to freeze, move the control to the left (less
cold). Remember to wait 24 hours between adjustments.
Crisper Humidity Control
(on some models)
You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW and HIGH.
LOW (open) for best storage of fruits and vegetables with skins.
HIGH (closed) for best storage of fresh, leafy vegetables.
Chilled Door Bin
(on some models)
Cool air from the freezer is directed to the refrigerator door bin
directly beneath the vents.
NOTE: The dairy compartment and can rack are not associated
with the Chilled Door Bin feature.
Chilled Door Bin Control
The chilled door bin control is located on the left-hand side of the
refrigerator compartment.
■ Slide the door chill control to the left to reduce the flow of cold
air to the bin and make it less cold.
■ Slide the door chill control to the right to increase the flow of
cold air to the bin and make it colder.
Water and Ice Dispensers
(on some models)
Depending on your model, you may have one or more of the
following options: the ability to select either crushed or cubed ice, a
special light that turns on when you use the dispenser, or a lock
option to avoid unintentional dispensing.
IMPORTANT: After connecting the refrigerator to a water source or
replacing the water filter, flush the water system. Use a sturdy
container to depress and hold the water dispenser lever for
5 seconds, then release it for 5 seconds. Repeat until water begins
to flow. Once water begins to flow, continue depressing and
releasing the dispenser lever (5 seconds on, 5 seconds off) until a
total of 3 gal. (12 L) has been dispensed. This will flush air from the
filter and water dispensing system, and prepare the water filter for
use. Additional flushing may be required in some households. As air
is cleared from the system, water may spurt out of the dispenser.
CONDITION/REASON: ADJUSTMENT:
REFRIGERATOR too warm REFRIGERATOR Control
one setting higher
FREEZER too warm/
too little ice
FREEZER Control
one setting higher
REFRIGERATOR too cold REFRIGERATOR Control
one setting lower
FREEZER too cold FREEZER Control
one setting lower
A. Chilled door bin control
A
14
The Water Dispenser
Allow 24 hours for the refrigerator to cool down and chill water.
IMPORTANT: Depending on your model, the small removable tray
at the bottom of the dispenser is designed to catch small spills and
allow for easy cleaning. There is no drain in the tray. The tray can
be removed from the dispenser and carried to the sink to be
emptied or cleaned.
To Dispense Water:
1. Press a sturdy glass against the water dispenser lever.
2. Remove the glass to stop dispensing.
NOTE: Water may have an off-flavor if you do not use the
dispenser periodically. Dispense enough water every week to
maintain a fresh supply.
The Ice Dispenser
Ice dispenses from the ice maker storage bin in the freezer. When
the dispenser lever is pressed:
■ A trap door opens in a chute between the dispenser and the ice
bin. Ice moves from the bin and falls through the chute.
■ When you release the dispenser lever, the trap door closes and
the ice dispensing stops. The dispensing system will not operate
when the freezer door is open.
Some models dispense both cubed and crushed ice. Before
dispensing ice, select which type of ice you prefer. The button
controls are designed for easy use and cleaning.
For crushed ice, cubes are crushed before they are dispensed. This
may cause a slight delay when dispensing crushed ice. Noise from
the ice crusher is normal, and pieces of ice may vary in size. When
changing from crushed to cubed, a few ounces of crushed ice will
be dispensed along with the first cubes.
To Dispense Ice:
1. Press button for the desired type of ice.
2. Press a sturdy glass against the ice dispenser lever. Hold the
glass close to the dispenser opening so ice does not fall outside
of the glass.
IMPORTANT: You do not need to apply a lot of pressure to the
lever in order to activate the ice dispenser. Pressing hard will
not make the ice dispense faster or in greater quantities.
3. Remove the glass to stop dispensing.
NOTE: The first few batches of ice may have an off-flavor from
new plumbing and parts. Throw the ice away. Also, take large
amounts of ice from the ice bin, not through the dispenser.
The Dispenser Light
The dispenser area has a light. It can be turned on manually by
pressing the ON button (touchpad or rocker switch).
On some models: Whenever you use the dispenser, the lever will
automatically turn the light on.
NOTE: See “Changing the Light Bulbs” for information on changing
the dispenser light bulb.
The Dispenser Lock (on some models)
The dispenser can be turned off for easy cleaning or to avoid
unintentional dispensing by small children and pets.
NOTE: The lock feature does not shut off power to the refrigerator,
to the ice maker, or to the dispenser light. It simply deactivates the
dispenser levers.
To turn off the dispenser, press the LOCK button. The indicator will
appear above the LOCK button and the ice and water dispensers
will not work. To unlock the dispenser, press the UNLOCK button
until the indicator appears. Then continue to dispense ice or water
as usual.
ICE
CRUSH CUBE
Cut Hazard
Use a sturdy glass when dispensing ice.
Failure to do so can result in cuts.
WARNING
LIGHT
OFF ON
DISPENSER
LOCK
UNLOCK
15
Water Filter Status Light
(on some models)
The water filter status light will help you know when to change your
water filter. When the status light changes from green to yellow,
this tells you that it is almost time to change the water filter. It is
recommended that you replace the filter when the status light
changes to red OR when water flow to your water dispenser or ice
maker decreases noticeably. The filter should be replaced at least
every 6 months depending on your water quality and usage. To
change the filter, see “Water Filtration System.”
After changing the water filter, reset the status light by pressing
and holding the RESET button for 2 seconds. The status light will
change from Replace (red) to Good (green) when the system is
reset.
Water Filtration System
Changing the Water Filter
The water filter is located in the base grille below the freezer
compartment door. It is not necessary to remove the base grille to
remove the filter.
1. Remove the filter by pressing the eject button and pulling
straight out on the filter cap.
NOTES:
■ Avoid twisting the cap when removing the filter because
this could cause the cap to come off. If this occurs, replace
the cap and pull the filter straight out.
■ There will be water in the filter. Some spilling may occur.
2. Remove the cap by turning it counterclockwise until it stops.
IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.
3. Take the new cartridge out of its packaging and remove the
covers from O-rings.
4. Place the cap (removed in Step 2) on the new filter. Align the
ridge on the cap with the arrow on the filter. Turn the cap
clockwise until it snaps into place.
5. Push the new filter into the opening in the base grille. As the
filter is inserted, the eject button will depress. The eject button
will pop back out when the filter is fully engaged.
6. Pull gently on the cap to check that the filter is securely in
place.
7. Flush the water system. See “Water and Ice Dispensers.”
INDICATOR: STATUS:
GOOD (green) New filter installed
ORDER (yellow) Order filter
REPLACE (red) OR
when water flow decreases
Replace water filter
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
A. Eject button
B. Filter cap
A. Cover
B. O-ring
A. Eject button
B. Arrow on filter
C. Ridge on cap
A
B
A
B
A
B
C
16
Using the Dispenser Without the Water Filter Cartridge
You can run the dispenser without a water filter cartridge. Your
water will not be filtered.
1. Remove the filter by pressing the eject button and pulling on
the cap. See “Changing the Water Filter” earlier in this section.
2. Remove the cap by turning it counterclockwise until it stops.
IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.
3. With the cap in a horizontal position, insert the cap into the
base grille until it stops.
4. Turn the cap counterclockwise until the cap slips into the
attachment slot. Then, turn the cap clockwise until it is in a
horizontal position.
NOTE: The cap will not be even with the base grille.
Ice Maker and Storage Bin
(on some models)
Turning the Ice Maker On/Off
Style 1
■ To turn ON the ice maker, simply lower the wire shutoff arm.
■ To manually turn off the ice maker, lift the wire shutoff arm to
the OFF (arm up) position and listen for the click. Ice can still
be dispensed, but no more can be made.
NOTE: Your ice maker has an automatic shutoff. As ice is made, the
ice cubes will fill the ice storage bin, and the ice cubes will raise the
wire shutoff arm to the OFF (arm up) position. Do not force the wire
shutoff arm up or down.
Style 2
The On/Off switch is located on the top right-hand side of the
freezer compartment.
■ To turn on the ice maker, slide the control to the ON (left)
position.
■ To manually turn off the ice maker, slide the control to the OFF
(right) position.
NOTE: Your ice maker has an automatic shutoff. The ice maker
sensors will automatically stop ice production, but the control will
remain in the ON (left) position.
REMEMBER:
■ Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
■ The quality of your ice will be only as good as the quality of the
water supplied to your ice maker. Avoid connecting the ice
maker to a softened water supply. Water softener chemicals
(such as salt) can damage parts of the ice maker and lead to
poor quality ice. If a softened water supply cannot be avoided,
make sure the water softener is operating properly and is well
maintained.
■ Do not use anything sharp to break up the ice in the storage
bin. This can cause damage to the ice container and the
dispenser mechanism.
■ Do not store anything on top of or in the ice maker or storage
bin.
Removing and Replacing Ice Storage Bin
Style 1
1. Pull the covering panel up from the bottom and then slide it
back toward the rear.
2. Lift the wire shutoff arm so it clicks into the OFF (up) position.
3. Lift up the front of the storage bin and pull it out.
4. Replace the bin by pushing it in all the way or the dispenser will
not work.
5. To restart ice production, push the wire shutoff arm down to the
ON position. Make sure the door is closed tightly.
Style 2
1. Hold the base of the storage bin with both hands and press the
release button to lift the storage bin up and out.
NOTE: It is not necessary to turn the ice maker control to the
OFF (right) position when removing the storage bin. The sensor
cover (“flipper door”) on the left wall of the freezer stops the
ice maker from producing ice if the door is open or the storage
bin is removed.
2. Replace the storage bin on the door and push down to make
sure it is securely in place.
17
REFRIGERATOR FEATURES
Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word “Accessory.” Not all accessories will fit all models. If
you are interested in purchasing one of the accessories, please call
the toll-free number on the back cover or in the “Accessories”
section.
Refrigerator Shelves
Your model may have glass or wire shelves. Store similar foods
together and adjust the shelves to fit different heights. This reduces
the time the refrigerator door is open and saves energy.
Shelves and Shelf Frames (Fixed and Slide-out)
To Remove and Replace a Shelf:
1. Pull the shelf forward to the stop. Tilt the front of the shelf up.
Lift to remove from the shelf supports.
2. Replace the shelf/frame by aligning the shelf with the shelf
supports. Slide the shelf onto the shelf supports. Be sure that the
shelf is securely in position.
Deli Bin
The deli drawer stores raisins, nuts, spreads, and other small items
at normal refrigerator temperatures.
To Remove and Replace the Deli Bin:
1. Remove the deli bin by sliding it straight out to the stop. Lift the
front and back of the bin up and out of the shelf supports. Tilt
the bin sideways to remove from the refrigerator compartment.
2. Replace the deli bin by sliding it back past the stop and
pushing into place.
Convertible Vegetable/Meat Drawer,
Crisper and Covers
(on some models)
Crisper and Convertible Vegetable Meat Drawers
To Remove and Replace Drawers:
1. Slide crisper or meat drawer straight out to the stop. Lift the
front of drawer with one hand while supporting the bottom of
drawer with other hand and slide the drawer out the rest of the
way.
2. Replace the crisper or meat drawer by sliding it back in fully
past the drawer stop.
Crisper or Vegetable/Meat Drawer Covers
To Remove and Replace Covers:
1. Remove the crisper and meat drawers. Press up in center of
crisper glass insert until it rises above the plastic frame. Holding
the crisper glass firmly, slide the glass insert forward to remove.
2. Lift crisper cover frame and remove. Repeat steps to remove
the meat drawer cover.
3. Replace back of meat drawer cover frame into supports or
slides on side walls of the refrigerator and lower or slide the
front of the cover frame into place.
4. Slide rear of glass insert into cover frame and lower front into
place. Repeat steps to replace the crisper cover.
Wine Rack
(on some models - Accessory)
To Install and Remove the Wine Rack:
1. Install the wine rack by aligning it with the three shelf tabs
located on the bottom of the shelf. Pull the wine rack straight
down until it locks onto the shelf tabs as shown.
2. To remove the wine rack, lift it straight up and off the shelf
tabs.
Utility Bin
(on some models - Accessory)
NOTE: For long-term storage, place eggs in a covered container
or in their original carton on an interior shelf.
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
18
FREEZER FEATURES
Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word “Accessory.” Not all accessories will fit all models. If
you are interested in purchasing one of the accessories, please call
the toll-free number on the cover or in the “Accessories” section.
Freezer Shelf
(number of shelves varies with model)
Style 1
To Remove and Replace the Shelf:
1. Slide the shelf to one side. Tilt the shelf upward to remove the
shelf from the support holes. To remove the left side from the
support holes, pull the shelf up and to the right.
2. Replace the shelf by inserting the left side of the shelf into the
support holes. Lower the right side of the shelf and insert into
support holes.
NOTE: Be sure that both sides of the shelf are positioned evenly
in the shelf support holes and the shelf is secure.
Style 2
To Remove and Replace the Shelf:
1. Lift the shelf up and off the supports.
2. Replace the shelf by lowering it onto the shelf supports. Be sure
that the shelf is securely in place.
Frozen Food Storage Guide
Storage times will vary according to the quality and type of food,
the type of packaging or wrap used (should be airtight and
moisture-proof), and the storage temperature. Ice crystals inside a
sealed package are normal. This simply means that moisture in the
food and air inside the package have condensed, creating ice
crystals.
Put no more unfrozen food into the freezer than will freeze within
24 hours (no more than 2 to 3 lbs of food per cubic foot
[907 to 1,360 g per 28 L] of freezer space). Leave enough space in
the freezer for air to circulate around packages. Be sure to leave
enough room for the door to close tightly.
For more information on preparing food for freezing, check a
freezer guide or reliable cookbook.
Freezer Basket or Bin
(plastic bin on some models)
The freezer basket or bin can be used to store bags of frozen fruits
and vegetables that may slide off freezer shelves.
To Remove and Replace the Freezer Basket or Bin:
1. Remove basket or bin by sliding it out to the stop.
2. Lift the front of the basket or bin and slide it out the rest of the
way.
3. Replace the basket or bin by positioning it on the side wall
guide rails. Lift the basket or bin front slightly while pushing it
past the guide rail stops and slide basket or bin in the rest of
the way.
DOOR FEATURES
Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word “Accessory.” Not all accessories will fit all models. If
you are interested in purchasing one of the accessories, please call
the toll-free number on the cover or in the “Accessories” section.
Door Rails or Bins
The door rails may be removed for easier cleaning.
Snap-On Door Rails or Bins
To Remove and Replace the Rails or Bins:
1. Remove the rails by pushing in slightly on the front of the
bracket while pulling out on the inside tab. Repeat these steps
for the other end of the rail.
2. Replace the rails by aligning the ends of the brackets with the
buttons on the sides of the door liner. Firmly snap bracket and
rail assembly onto the tabs above the shelf as shown.
Drop-In Door Rails
To Remove and Replace the Rails:
1. Remove the rails by pulling straight up on each end of the rail.
2. Replace the rails by sliding the shelf rail into the slots on the
door and pushing the rail straight down until it stops.
19
Door Bins
To Remove and Replace the Bins:
1. Remove the bin by lifting it and pulling it straight out.
2. Replace the bin by sliding it in above the desired support and
pushing it down until it stops.
REFRIGERATOR CARE
Cleaning
Both the refrigerator and freezer sections defrost automatically.
However, clean both compartments about once a month to avoid
buildup of odors. Wipe up spills immediately.
To Clean Your Refrigerator:
1. Unplug refrigerator or disconnect power.
2. Remove all removable parts from inside, such as shelves,
crispers, etc.
3. If your model has a touch screen display on the dispenser
panel, clean the screen using a soft, lint-free cloth. Mix a mild
detergent with water, then use the mixture to dampen the cloth
and gently wipe the screen.
■ To avoid unintentionally changing settings, make sure the
refrigerator is unplugged or the power is disconnected
before wiping the screen.
■ Do not over-saturate the cloth. Do not spray or wipe liquids
directly onto the screen. Do not use abrasive or harsh
cleaners such as window sprays, scouring cleansers,
flammable fluids, cleaning waxes, concentrated detergents,
nail polish remover, bleaches or cleansers containing
petroleum products. Do not use paper towels, scouring
pads, or other harsh cleaning tools. These can scratch or
damage materials.
4. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
■ Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, cleaning
waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on plastic parts, interior and
door liners or gaskets. Do not use paper towels, scouring
pads, or other harsh cleaning tools. These can scratch or
damage materials.
■ To help remove odors, you can wash interior walls with a
mixture of warm water and baking soda (2 tbs to 1 qt
[26 g to 0.95 L] of water).
5. Determine whether your refrigerator exterior is painted metal,
Ultra Satin™ (stainless look) finish, brushed aluminum or
stainless steel, and choose the appropriate cleaning method.
NOTE: Ultra Satin™ (stainless look) finish has a smooth,
uniform color with a glossy finish that resists fingerprints.
Stainless steel has a distinct grainy texture with variation in
color that is natural to steel.
Painted metal: Wash exteriors with a clean sponge or soft cloth
and a mild detergent in warm water. Do not use abrasive or
harsh cleaners, or cleaners designed for stainless steel. Dry
thoroughly with a soft cloth. Additionally, to avoid damage to
painted metal exteriors, apply appliance wax (or auto paste
wax) with a clean, soft cloth. Do not wax plastic parts.
Brushed aluminum: Wash with a clean sponge or soft cloth and
a mild detergent in warm water. Do not use abrasive or harsh
cleaners, or cleaners designed for stainless steel. Dry thoroughly
with a soft cloth.
Ultra Satin™ (stainless look) finish: Wash with a clean sponge
or soft cloth and a mild detergent in warm water. Do not use
abrasive or harsh cleaners, or cleaners designed for stainless
steel. Dry thoroughly with a soft cloth.
Stainless steel finish: Wash with a clean sponge or soft cloth
and a mild detergent in warm water. Do not use abrasive or
harsh cleaners. Dry thoroughly with a soft cloth.
■ To keep your stainless steel refrigerator looking like new
and to remove minor scuffs or marks, it is suggested that
you use the manufacturer’s approved Stainless Steel
Cleaner and Polish. To order the cleaner, see “Accessories.”
IMPORTANT: This cleaner is for stainless steel parts only!
■ Do not allow the Stainless Steel Cleaner and Polish to come
into contact with any plastic parts such as the trim pieces,
dispenser covers or door gaskets. If unintentional contact
does occur, clean plastic part with a sponge and mild
detergent in warm water. Dry thoroughly with a soft cloth.
6. There is no need for routine condenser cleaning in normal home
operating environments. If the environment is particularly
greasy or dusty, or there is significant pet traffic in the home,
the condenser should be cleaned every 2 to 3 months to ensure
maximum efficiency.
If you need to clean the condenser:
■ Remove the base grille. See “Base Grille” graphic or “Base
Grille” section.
■ Use a vacuum cleaner with a soft brush to clean the grille,
the open areas behind the grille and the front surface area
of the condenser.
■ Replace the base grille when finished.
7. Plug in refrigerator or reconnect power.
WARNING
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
20
Changing the Light Bulbs
NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to
replace the bulb with one of the same size and shape. The
dispenser light requires a heavy duty 10-watt bulb. All other lights
require a 40-watt appliance bulb. Replacement bulbs are
available from your dealer.
1. Unplug refrigerator or disconnect power.
2. Remove light shield when applicable as shown.
NOTE: To clean the light shield, wash it with warm water and
liquid detergent. Rinse and dry the shield well.
3. Remove light bulb and replace with one of the same size, shape
and wattage.
4. Replace light shield when applicable as shown.
5. Plug in refrigerator or reconnect power.
Dispenser Light (on some models)
Reach through the dispenser area to remove and replace
light bulb.
Refrigerator Control Panel Light
Reach behind the refrigerator control panel to remove and replace
light bulb.
Crisper Lights
■ If necessary, remove the top crisper drawer for easier access to
the crisper light shield. Remove the light shield by squeezing the
top and bottom in toward the center and pulling the bottom
tabs out of the refrigerator liner, then sliding the top tabs down
and out.
■ Replace the light shield by sliding the top tabs up into the
slotted holes in the refrigerator liner, then snapping the bottom
tabs into place. If necessary, replace the top crisper drawer.
Upper Freezer Light (on some models)
■ Remove light shield by grasping the top center of the shield
and pulling forward while turning it slightly to one side. If
necessary, remove top crisper drawer to gain access to the
crisper light shield.
■ Replace the light shield by inserting the tabs on one end into
the slotted holes in the refrigerator or freezer liner. Then, gently
bend the shield at the center to insert the tabs on the other end.
Lower Freezer Light (on some models)
■ Remove the light shield by grasping the sides and squeezing in
toward the center. Once the side hooks of shield are free from
the freezer lining, pull down the shield.
■ Replace the light shield by squeezing the sides toward the
center and inserting the side hooks into the slotted holes. Once
the side hooks are in place, snap the front tab into the slotted
hole.
Power Interruptions
If the power will be out for 24 hours or less, keep the door or doors
closed (depending on your model) to help food stay cold and
frozen.
If the power will be out for more than 24 hours, do one of the
following:
■ Remove all frozen food and store it in a frozen food locker.
■ Place 2 lbs (907 g) of dry ice in the freezer for every cubic foot
(28 L) of freezer space. This will keep the food frozen for 2 to
4days.
■ If neither a food locker nor dry ice is available, consume or can
perishable food at once.
REMEMBER: A full freezer stays cold longer than a partially filled
one. A freezer full of meat stays cold longer than a freezer full of
baked goods. If you see that food contains ice crystals, it may be
refrozen, although the quality and flavor may be affected. If the
condition of the food is poor, dispose of it.
Vacation and Moving Care
Vacations
If You Choose to Leave the Refrigerator On While You’re
Away:
1. Use up any perishables and freeze other items.
2. If your refrigerator has an automatic ice maker:
■ Raise wire shutoff arm to OFF (up) position or move the
switch to the OFF (right) setting.
■ Shut off water supply to the ice maker.
3. Empty the ice bin.
A. Dispenser light
A
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
Kenmore 106.5035 Series Manuel utilisateur
- Catégorie
- Frigos
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Kenmore 106.5035 Series User manual
- español: Kenmore 106.5035 Series Manual de usuario
