Jandy H0622800_REVE Nicheless LED Underwater Light Le manuel du propriétaire

H0622800 REV E

ENGLISH | FRANÇAIS | ESPAÑOL

OWNER’S MANUAL

FOR YOUR SAFETY - This product must be installed and serviced by a contractor

who is licensed and qualified in pool equipment by the jurisdiction in which the

product will be installed where such state or local requirements exist. The maintainer

must be a professional with sufficient experience in pool equipment installation and

maintenance so that all of the instructions in this manual can be followed exactly.

Before installing this product, read and follow all warning notices and instructions

that accompany this product. Failure to follow warning notices and instructions

may result in property damage, personal injury, or death. Improper installation and/

or operation may void the warranty.

Improper installation and/or operation can create unwanted electrical hazard which

can cause serious injury, property damage, or death.

ATTENTION INSTALLER - This manual contains important information about the

installation, operation and safe use of this product. This information should be

given to the owner/operator of this equipment.

WARNING

Jandy Nicheless LED Underwater Light

Page 2 ENGLISH Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual

FCC Regulatory Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

CAUTION: Changes or modications not expressly approved by the

party responsible for compliance may void the user’s authority to operate

the equipment.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual ENGLISH Page 3

Table of Contents

Section 1. Important Safety Instructions ............. 4

Section 2. General Description ............................. 5

2.1 Product Overview ..................................................................... 5

2.2 Product Contents .................................................................... 5

Section 3. Installing the Jandy®

Nicheless LED Light ............................ 6

3.1 Preparing the Light Fixture for Installation ............................... 6

3.2 Installing the Light Fixture ....................................................... 8

3.3 Wet Area Installations ............................................................. 9

Section 4. Wiring Options for Controlling

Jandy Nicheless LED Lights ............... 9

4.1 Wiring to an AquaLink® RS Control System ............................. 9

4.2 Wire Gauge and Length ......................................................... 10

4.3 Wiring to a Switch .................................................................. 11

4.4 Twelve (12) Volt Installation ................................................... 11

Section 5. Jandy Nicheless Underwater LED

Light Operating Instructions ............ 12

5.1 Light Synchronization ............................................................. 12

5.2 Operating the Light ................................................................. 13

Section 6. S-Series Nicheless Underwater

LED Light Operating Instructions .... 14

6.1 Light Synchronization for S-Series Lights .............................. 14

6.2 Operating the S-Series Lights ................................................ 14

Section 7. H-Series Nicheless Underwater

LED Light Operating Instructions .... 15

7.1 Light Synchronization for H-Series Lights .............................. 15

7.2 Operating the H-Series Lights ................................................ 15

Section 8. P-Series Nicheless Underwater

LED Light Operating Instructions .... 17

8.1 Operating the P-Series Lights ................................................ 17

Section 9. Winterizing .........................................18

Section 10. Troubleshooting ................................. 19

Page 4 ENGLISH Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual

Section 1. Important Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS PERTAINING TO A RISK

OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

READ AND FOLLOW ALL INSTRUCTIONS

When installing and using this electrical equipment, basic safety

precautions should always be followed, including the following:

WARNING

Before installing this underwater light, read and follow all warning

notices and instructions accompanying this light. Failure to follow safety

warnings and instructions can result in severe injury, death, or property

damage.

Visit www.zodiacpoolsystems.com for additional free copies of these

instructions or call Zodiac Technical Support at 800.822.7933 (U.S.) or

888.647.4004 (Canada)

DANGER

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION. This

underwater light must be installed by a licensed or certified electrician

in accordance with the National Electrical Code® and applicable local

codes and ordinances. In Canada, the Canadian Electrical Code and

all applicable local codes and ordinances must be adhered to. Improper

installation will create an electrical hazard, which could result in death or

serious injury to pool or spa users, installers, or others due to electrical

shock, and may also cause damage to property. Read and follow the

specific instructions below.

CAUTION

Except when the Jandy® Nicheless Underwater LED Lights are installed

in an area of the swimming pool that is not used for swimming and the

lens is adequately guarded to keep any person from contacting it, the

light shall be installed in or on a wall of the pool, with the top of the lens

opening not less than 4 inches (102 mm) below the normal water level of

the pool.

SAVE THESE INSTRUCTIONS

ATTENTION INSTALLER

This manual contains important information about the installation,

operation and safe use of this product. This information should be given

to the owner/operator of this equipment.

Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual ENGLISH Page 5

SAVE THESE INSTRUCTIONS

Section 2. General Description

2.1 Product Overview

This manual provides instructions for installing and replacing the Jandy

Nicheless Underwater LED Lights for pool and spa use.

CAUTION

The Jandy Nicheless LED Underwater Lights are not serviceable

and therefore contain no serviceable parts. In order to prevent risk of

property damage and/or injury, no service should be attempted to the

light in the event of a malfunction. The complete light assembly must be

replaced.

2.2 Product Contents

1

2

3

46

7

5

1 - Jandy Nicheless Underwater LED Light

2 - Protective Cover (See Page 7)

3 - White Cosmetic Cover (See Page 7)

4 - Gray Cosmetic Cover (See Page 7)

5 - Installation Tool (See Page 7)

6 - Quick Reference Guide

7 - Nicheless LED Underwater Light Owner’s Manual

WARNING

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION, which

could result in serious injury or death. The Jandy® Nicheless LED

Lights are only available for 12-volt AC power. For supply connection,

use only an isolating low voltage power supply with ungrounded output,

evaluated and listed by a NRTL for swimming pool use.

Page 6 ENGLISH Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual

Section 3. Installing the Jandy Nicheless LED

Light

WARNING

Risk of Electrical Shock or Electrocution. This underwater light

must be installed by a licensed or certified electrician or a qualified pool

serviceman in accordance with the National Electrical Code® (Canadian

Electrical Code, in Canada) and all applicable local codes and

ordinances. Improper installation will create an electrical hazard, which

could result in death or serious injury to pool or spa users, installers or

others due to electrical shock, and may also cause damage to property.

Always disconnect the power to the light at the circuit breaker before

installing or servicing the light. Failure to do so could result in death or

serious injury to serviceman, pool or spa users or others due to electrical

shock.

NOTE: Jandy Nicheless Lights are Low Voltage and do not have any

exposed metal and as such do not require a separate ground or

bonding wire.

3.1 Preparing the Light Fixture for Installation

NOTE: The electrician must complete preparatory steps before light xture

is installed. See Figure 1.

Verify that the pool meets the requirements of the current National Electri-

cal Code® (Canadian Electrical Code, in Canada) and all local codes and

ordinances. A licensed or certied electrician must install the electrical

system to meet or exceed those requirements before the underwater light is

installed. Some of the requirements of the National Electrical Code, which

the pool electrical systems must meet, are as follows:

1. The junction box or the low-voltage magnetic transformer must be

located at least eight (8) inches (measured from the inside of the

bottom of the junction box or transformer) above the MAXIMUM

water level, OR at least four (4) inches above the ground level or pool

deck, whichever is greater. The junction box or 12VAC magnetic

transformer must also be installed at least forty-eight (48) inches (4 ft.)

from the edge of the pool. See Figure 1.

2. 1.5” pipe must be installed through the bond beam followed by 1”

conduit for the cord using sweep elbows only for turns. Do not use 90

degree elbows. It is highly recommended to use 1.5” pipe throughout

the entire width of the bond beam, however, the minimum length for

the particular light being installed is specied in Table 1.

Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual ENGLISH Page 7

3. A standard 1.5” plastic wall / return tting (not included) must be

installed so that the top edge of the underwater light’s lens is at least 4

inches (10.2 cm) below the surface of the water in the pool.

See Figure 1.

NOTE: For optimal lighting results it is recommended to place lights 12-18”

below the water line.

NOTE: To be certain that the pool’s electrical system meets all applicable

requirements, the electrician should also consult the local building

department.

12 VAC Class 2 Magnetic

Transformer or

Junction Box

48” min.

Check AHJ for other J-box requirements

8” minimum to maximum water level

1.5” pipe. Length requirement varies

by model. (See Table 1)

Rigid 1” electrical conduit. Sweep

elbows only, no 90º elbows.

NOTE: Vertical installations such as bench and walk-out locations will use ALL of the same clearance requirements.

The light face must be completely snug with the light fitting without any protrusion from the light fixture.

4” minimum to top of lens

Maximum possible water line.

(top of copping)

Figure 1. Jandy® LED Light Installation with Standard 1.5” Plastic Fitting

Use the chart below to determine the appropriate pipe length for your

installation.

WATTS MINIMUM LENGTH FOR 1.5” PIPE

6W 7”

12W 10”

24W 10”

All products listed above come in a variety of cord lengths. Cord lengths

come in 50, 100 & 150 feet lengths.

Table 1. Jandy® LED Light Minimum 1.5” pipe length

Page 8 ENGLISH Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual

3.2 Installing the Light Fixture

NOTE: Perform these steps only after the electrical system requirements are met.

1. Keep protective cover on to protect the light during installation.

The light face must be completely

snug with the return fitting without

any protrusion from the light fixture.

NOTE: Gasket helps ensure

that the conduit is not a

potential leak path.

See Table 1

for min. length

requirements

Figure 2. Standard installation with 1.5” pool wall fitting

2. Snake the electric cord through the conduit outlet of the wall tting,

into the conduit and up to the location of the pool transformer. Cut the

cord 18”-24” beyond the length needed to reach the transformer to

allow for a service loop. Pull the xture snug to the wall tting.

3. Remove protective cover after construction (including plastering for

gunite pools) is complete. Do not plaster the pool with the construction

cover removed.

4. Install cosmetic cover if desired.

5. Apply Teon™ silicone lube to threads to assist with threading.

NOTE: When using a 1 1/2” MIP tting on the back of a SP-1022 or

SP-1408 Wall Fitting, the interior of the Spears and Dura MIP are too small

for use with the Jandy® Nicheless LED Lights.

6. Using the included installation tool,

thread the light into the wall tting

until it is snug. The light face must

be completely ush with the return

tting. Please provide the pool

owner with a minimum of 1 key

upon job completion.

Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual ENGLISH Page 9

NOTE: Service

Loop not applicable

for Junction Box

Installations.

Vertical Installation

12VAC Magnetic Pool Transformer,

see table 3.2 for more details

The light face must be completely

snug with the light fitting without

any protrusion from the light fixture.

Conduit to 12VAC Magnetic Transformer

12VAC Magnetic Transformer

The light must be installed with the

light face completely snug with the

light fitting, without any protrusion

from the light fixture, and in

accordance with applicable local

codes and AHJ (Authority Having

Jurisdiction) requirements.

Figure 3. Standard installation with 1.5” pool wall fitting

3.3 Wet Area Installations

For wet area lighting within 10 feet (3M) of a pool or spa, use 6 Watt

Models ONLY. Except when the luminaire is adequately guarded, the

luminaire shall be installed in areas not subject to incidental contact from

people, pets, vehicles, and foot traffic.

Section 4. Wiring Options for Controlling

Jandy® Nicheless LED Lights

NOTE: Always consider the cable length when calculating the input

voltage at the transformer. The maximum run of service between

transformer and lights should not exceed 150ft. in length, inclusive

of the use of a J Box or not.

To the extent allowed by local installation codes in effect in the installation

jurisdiction and capacity of the electrical equipment, multiple Jandy lights

may be controlled with a single switch and a 12VAC magnetic transformer

so their colors may be synchronized.

IMPORTANT NOTE: All xtures must be tied into the same transformer,

circuit or switch for synchronization to occur. The use of Solid Core over

Stranded wire and terminating Bus Bars is strongly recommended.

4.1 Wiring to an AquaLink® Controller

The Jandy Nicheless LED Lights can be controlled by an AquaLink

controller. Connect the transformer powering the lights to one of the

auxiliary relays in the AquaLink.

Refer to Figure 4 to connect the Jandy Nicheless LED Lights to the Power

Center.

Page 10 ENGLISH Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual

4.2 Wire Gauge and Length

CAUTION

Jandy® Nicheless Underwater LED Lights are low voltage fixtures.

Improper wire gauge and wire length can effect the performance of these

products. Follow the guidelines below to determine the proper operation

and optimum performance of the lights.

Voltages are determined by the measured voltage level at the Bus Bar where

the transformer and cords are connected.

NOTE: Each color mode has a slightly different power draw

6W & 12W lights: Min/Max Voltage per cord length

Cord Length Min. Voltage Max. Voltage

50 Feet 9.4VAC 12.4VAC

100 Feet 10.7VAC 13.2VAC

150 Feet 11.82VAC 13.8VAC

24W Lights: Min/Max Voltage per cord length

Cord Length Min. Voltage Max. Voltage

50 Feet 10.34VAC 12.56VAC

100 Feet 10.9VAC 13.5VAC

150 Feet 11.43VAC 14.1VAC

Table 2. Jandy® LED Light Voltage Min/Max Levels

WARNING

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION,

which could result in serious injury or death. A Ground Fault

Circuit Interrupter (GFCI) for 120 Volt transformers should be used if

required by the transformer manufacturer or if required by the local

applicable code and/or Authority Having Jurisdiction (AHJ). When

a GFCI is used, the conductors on the load side of the GFCI circuit

shall not occupy conduit, boxes, or enclosures containing other

conductors unless the additional conductors are also protected by a

GFCI. Refer to local codes for complete details.

Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual ENGLISH Page 11

WARNING

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION,

which could result in serious injury or death. The Jandy Nicheless

LED Lights are only available for 12-volt AC power. For supply

connection, use only an isolating low voltage power supply with

ungrounded output, evaluated and listed by a NRTL for swimming

pool use.

4.3 Wiring to a Switch

The Jandy® Nicheless LED Lights can be wired to a switch to manually

operate the lights. Refer to Figure 4 to connect the lights into the switch.

AquaLink® Aux

Black

GFCI*

120 volts to

12VAC

Transformer

White

Ground

*If required by transformer manufacturer’s instructions

or by local code and AHJ requirements.

Line

Neutral

Ground

Black

White

Green

Relay or Switch

Figure 4. Wiring Jandy Nicheless Underwater Lights

4.4 Twelve (12) Volt Installation

A 12-14 Volt AC Magnetic Transformer must be used to power all 12-Volt

lights.

NOTE For optimum performance do not exceed the load factor specied

by the instructions included with the transformer.

To ensure maximum safety, use only a Class 2 magnetic transformer that

can supply 12-14 Volts AC to power all 12-Volt lights. The transformer

must be listed or certified by a Nationally Recognized Testing Laboratory

(NRTL) for the intended use.

Page 12 ENGLISH Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual

CAUTION

To prevent risk of fire which could result in property damage,

and to ensure optimum performance, do not exceed the load

factor specified in the instructions provided by the transformer

manufacturer.

Class 2 Magnetic Transformer

Output: 12-14 VAC

Ground Bar

White - Neutral

Green - Ground

Black - Hot (Line)

Time clock, Automation relay,

or switch

Figure 5. Wiring LED Lights to a 12 Volt Magnetic Transformer

NOTE A magnetic low-voltage dimmer switch or dimming relay may be

used when Jandy Nicheless WHITE ONLY lights are installed.

Jandy color lights are NOT DIMMABLE and are NOT COMPATIBLE

with dimmer switches or dimmer relays.

NOTE Sections 5-8 apply to color (RGBW or RGB) lights only. All xtures

must be tied into the same transformer, circuit or switch for

synchronization to occur.

Section 5. Jandy® Nicheless Underwater LED

Light Operating Instructions

5.1 Light Synchronization

1. Turn the light ON. If the light has been off for 7 seconds or longer, the

light will turn on with the last color selected.

2. To synchronize multiple lights to the same color mode, you will need to

reset to the beginning of the color mode sequence. With the lights ON,

turn them OFF for five (5) seconds, then turn ON again. All of the lights

will reset to the Alpine White color mode. If all of the lights are not in

the Alpine White color mode, they have not been synchronized, repeat

step 2.

Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual ENGLISH Page 13

5.2 Operating the Light

3. To change the color mode, turn the light OFF for one 1-3 seconds.

Continue turning OFF and ON until the desired light color mode is

reached. See Table 3 for the color mode sequence.

Example: If you followed step 3 and are now on Sky Blue and want the lights to be

Violet, then the lights must be turned off and on 7 times to bring you to Violet.

Sequence Order Color Modes

1 Alpine White

2 Sky Blue

3 Cobalt Blue

4 Caribbean Blue

5 Spring Green

6 Emerald Green

7 Emerald Rose

8Magenta

9Violet

10 Slow Color Splash

11 Fast Color Splash

12 America the Beautiful

13 Fat Tuesday

14 Disco Tech

Table 3. Color Mode Sequence

4. The lights have memory. If the lights are off for 7 seconds or more, the

next time the lights are turned on, they will return to the last color mode

they were on prior to being turned off (Step 1 listed above). This function

allows you to keep your lights returning to your favorite color mode

every time the lights are turned back on.

NOTE To synchronize colors on multiple Jandy® Nicheless Underwater

LED Light systems wired to separate switches, perform the above

actions on all of their switches simultaneously. All Jandy Nicheless

Underwater LED Lights will synchronize automatically if activated by

the same switch. No other accessories are required.

Page 14 ENGLISH Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual

Section 6. S-Series Nicheless Underwater LED

Light Operating Instructions

6.1 Light Synchronization for S Series Lights

1. Turn the light ON and wait for 20 seconds. The lights will first come on

white for 10-15 seconds and then return to the color mode it was on prior

to being turned off.

2. To synchronize lights, turn the lights off, wait 6-9 seconds and then turn

them back on. You should see three quick flashes (red, green & blue),

then all the lights will reset to the first color mode (Treasure Island)

3. (A) If you do not see three quick flashes, then the lights did not reset.

(B) If you did not wait long enough (shorter than 6 seconds) the lights

will advance to their next color mode. They are not synced as each light

could be in different color modes.

(C) If you wait too long (longer than the 9 seconds) they all will go to

white for 10-15 seconds, looking like they’re synced BUT AFTER 15

seconds they will return to their previous color mode (which at this point

the lights are still unsynchronized).

4. Repeat step 1 - 3 until synchronization is accomplished.

6.2 Operating the S Series Lights

1. To move to the next color mode, turn the lights off for 1-2 seconds and

turn back on. Repeat until desired color mode is found.

Example: If you are now on Fixed Green and want the lights to be White,

then the lights must be turned off and on 7 times to bring you to Moonlight

White.

Sequence

Order Color Modes for S Series Lights

1Treasure Island / Slow Color Change

2Moonlight White / Fixed White

3SAVI Blue / Fixed Blue

4Sargasso Sea / Fixed Green

5Blue Lagoon / Fixed Light Blue

6Passion Pink / Fixed Light Blue

7Caribbean Hues / Blue and Green Slow Color Change

8Copacabana / Magenta, Yellow and Orange Slow Color Change

9Dance Party / Multi Color Strobe Effect

Table 4. Color Mode Sequence for S Series Lights

Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual ENGLISH Page 15

2. The lights have memory. If the lights are off for 10 seconds or more, the

next time the lights are turned on, they will go to white for approximately

10-15 seconds and then return to the last color mode they were on

prior to being turned off. This function allows you to keep your lights

returning to your favorite color mode every time the lights are turned

back on.

NOTE To synchronize colors on multiple S-Series Nicheless Underwater

LED Light systems wired to separate switches, perform the

above actions on all of their switches simultaneously. All S-Series

Nicheless Underwater LED Lights will synchronize automatically if

activated by the same switch. No other accessories are required.

Section 7. H-Series Nicheless Underwater

LED Light Operating Instructions

7.1 Light Synchronization for H-Series Lights

1. Turn the light ON. The lights will first come on white for 15 seconds and

then return to the color mode it was on prior to being turned off.

2. H-Series Lights may be operated independently or together depending

upon the initial installation of your lights. All H-Series lights that are

wired to the same 12V Transformer/Switch will synchronize their

operation of the 17 Color modes. If they do get out of sync, turn the

switch on then back off - wait between 6 and 9 seconds and turn the

switch back on. They should now all be in position #1.

7.2 Operating the H-Series Lights

1. To move to the next color mode, turn the lights off for 1-3 seconds and

turn back on. Repeat until desired color mode is found.

Example: If you are now on Deep Blue and want the lights to be White, then the

lights must be turned off and on 5 times to bring you to White.

Page 16 ENGLISH Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual

Sequence

Order Color Modes (Universal Hayward® ColorLogic® emulation)

1Color Show - Voodoo Lounge

2 Deep Blue Sea

3 Royal Blue

4 Afternoon Skies

5 Aqua Green

6 Emerald

7 Cloud White

8 Warm Red

9 Flamingo Pink

10 Vivid Violet

11 Sangria Dark Purple/Red

12 Color Show - Twilight

13 Color Show - Tranquility

14 Color Show - Gemstone

15 Color Show - USA

16 Color Show - Mardi Gras

17 Color Show - Cool Cabaret

Table 5. Color Mode Sequence for H-Series Lights

2. The lights have memory. If the lights are off for 60 seconds or more, the

next time the lights are turned on, they will go to white for approximately

15 seconds and then return to the last color mode they were on prior to

being turned off. This function allows you to keep your lights returning

to your favorite color mode every time the lights are turned back on.

3. H-Series LED Colored Nicheless Lights are specifically designed to be

compatible with by select Hayward® Controls and Zodiac® Rev T.2 RS

Systems for direct switching/access to colors and programs. Please refer

to Hayward and Zodiac Series controls for installation and operational

directions.

NOTE At NO TIME shall the H-Series lights be used in conjunction with

any other lights. The color choices, shows and operations are

entirely different.

Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual ENGLISH Page 17

Section 8. P-Series Nicheless Underwater LED

Light Operating Instructions

8.1 Operating the P-Series Lights

1. Turn the light ON and wait for 20 seconds. The lights will first come on

white for a few seconds and then return to the color mode it was on prior

to being turned off.

2. P-Series LED Colored Nicheless Lights are specifically designed to

be compatible with by select Pentair® Controls and Jandy Aqualink®

Controls with Pentair IntelliBrite® control for direct switching/access to

colors and programs WITHOUT having to toggle sequences ON/OFF.

Please refer to the controller manual for installation and operational

directions.

NOTE When using the above mentioned controls - when programming the

Light Function - the general selection choice offered that should be

selected is IntelliBrite. The color and show names will be slightly

different but all operations will be correct.

NOTE At NO TIME shall the P-Series lights be used in conjunction with

any other lights. The color choices, shows and operations are

entirely different.

3. To move to another color mode, cycle the lights OFF/ON the selected

number of times listed below.

Example: If you are now on Blue (8) and want the lights to be Magenta (12), then

the lights must be turned off and on twelve (12) times to bring you to Magenta. To

move to Old School, turn OFF/ON 1 time.

WARNING

During OFF/ON Cycle, before the selected mode is displayed, no

illumination will occur. During this period of time the pool/spa will be dark

and precautions should be taken to avoid unforeseen accidents. Failure

to observe this warning may result in serious injury or death to pool/spa

users.

Page 18 ENGLISH Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual

Cycle

Number

Color Modes for P-Series Lights (Pentair® IntelliBrite®

emulation)

1 SAm® Mode

2Party Mode

3Romance Mode

4Caribbean Mode

5American Mode

6 California Sunset

7Royal Mode

8 Blue

9 Green

10 Red

11 White

12 Magenta

13* Hold : Saves the current color choice during a color show

14* Recall: Turns on last saved color selection selected in

position #13

* These 2 Modes are specically used with advanced control systems and not

manual operations

Table 6. Color Mode Sequence for P-Series Lights

4. The lights have memory. If the lights are off for 5-10 seconds, the next

time the lights are turned on, they will go to white for a few seconds and

then return to the last color mode they were on prior to being turned off.

This function allows you to keep your lights returning to your favorite

color mode every time the lights are turned back on.

Section 9. Winterizing

Do not keep the winter water level at the level of the light. Make certain

that the water level is left at least 4” or more above or below the light

depending on the pool’s other winterization needs. Consult a Local

Swimming Pool Professional for proper winterization. At NO TIME should

there be water removed from the pool without checking ground water

tables.

Nicheless Underwater LED Lights | Owner’s Manual Nicheless Underwater LED Lights | Owner’s Manual ENGLISH Page 19

Section 10. Troubleshooting

Use the troubleshooting information in the following table for suggestions.

Symptom Problem Corrective Action

All lights fail to illuminate Lights are not

recieving power

Check 120VAC power supply

into transformer. Check for

12VAC output at transformer.

Check or reset GFCI. Make

sure 120 volts has not been

used in the installation - if so

damage is assured and is NOT

WARRANTABLE.

One or more lights are

dim, blinking or not

working

Poor connection or

improper wire gauge

Separate each light and

independently wire 12V to

the single light only. Repeat

this process on each light. If

junction box is being used,

check for proper connection of

light cord. Verify that the correct

wire gauge is being used

between the transformer and

junction box.

Colored lights out of

synch

Improper voltage

supply or poor

connection to the

light

Verify that proper wire

connections are being achieved

for the lights that are out of

sync. Reset all the lights to

white by turning lights OFF for

ve (5) seconds, then turning

ON

Light is blinking Light is too hot Conrm that the light is

submerged in water that does

not exceed a temperature of

104F (40C)

Different colors from

different lights

Color lights of

different series

installed on same

circuit

Verify if one or more lights is of

a different series type than the

desired series and replace with

the desired series type.

Zodiac Pool Systems LLC

2882 Whiptail Loop # 100

Carlsbad, CA 92010, USA

Jandy.com | 1.800.822.7933

Zodiac Pool Systems Canada, Inc.

2-3365 Mainway

Burlington, ON L7M 1A6, Canada

Jandy.ca | 1.800.822.7933

A Fluidra Brand

is a registered

trademark of Zodiac International, S.A.S.U., used under license. All other

trademarks are the property of their respective owners.

H0622800_REVE

ETL LISTED

CONFORMS TO

UL STD 676

CERTIFIED TO

CAN/CSA C22.2 NO.89

La page charge ...

Jandy H0622800_REVE Nicheless LED Underwater Light Le manuel du propriétaire

Jandy H0622800_REVE Nicheless LED Underwater Light Le manuel du propriétaire

dans d''autres langues