Murray 7800889 Manuel utilisateur

Marque: Murray

Modèle: 7800889

Catégorie: Tondeuses à gazon

Taper: Manuel utilisateur

Ce manuel convient également à

7800890

Operator's Manual

7105382

Rev. A

22” WALK BEHIND

MOWER

Model No.Description

7800889 MD22550FC

7800890 M22550FC

en fr

Not for

Reproduction

Thank You for purchasing this quality-built Murray product. We’re pleased that you placed your confidence in the Murray

brand. When operated and maintained according to the instructions in this manual, your Murray product will provide many

years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with the machine and how to

avoid them. This machine is designed and intended only for finish cutting of established lawns and is not intended for any

other purpose. It is important that you read and understand these instructions thoroughly before attempting to start or operate

this equipment. Save these original instructions for future reference.

Complete the following information on your Murray purchase.

Date of Purchase_______________________________________________________________________________________

Retailer______________________________________________________________________________________________

Retailer's Phone Number________________________________________________________________________________

Equipment

Model Number_________________________________________________________________________________

Serial Number ______________________________________________________________________________

Engine

Model___________________________Type___________________________Code__________________________

Not for

Reproduction

Table of Contents

Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Handle Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Grass Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Mulching Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Mulching Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Side Discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

How to Prepare the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Final Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Engine Stop Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

How to Stop the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

How to Start the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Rules for Safe and Effective Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Adjusting the Height of Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Maintenance Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Mower Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Engine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Warranties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Slope Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

WARNING

Battery posts, terminals and related accessories contain

lead and lead compounds, chemicals known to the State of

California to cause cancer and birth defects or other

reproductive harm. Wash hands after handling.

WARNING

Engine exhaust, some of its constituents, and certain

vehicle components contain or emit chemicals known to

the State of California to cause cancer or other reproductive

harm.

Not for

Reproduction

www.murray.com4

Operator Safety

Operating Safety

Power equipment is only as safe as the operator. If it is misused, or

not properly maintained, it can be dangerous! Remember, you are

responsible for your safety and that of those around you.

Use common sense, and think through what you are doing. If you are

not sure that the task you are about to perform can be safely done

with the equipment you have chosen, ask a professional: contact your

local authorized dealer.

Read the Manual

The operator’s manual contains important safety information you need to

be aware of BEFORE you operate your unit as well as DURING operation.

Safe operating techniques, an explanation of the product’s features and

controls, and maintenance information is included to help you get the

most out of your equipment investment.

Be sure to completely read the Safety Rules and Information found on the

following pages. Also completely read the Operation section.

Children

Tragic accidents can occur with children. Do not allow them any-

where near the area of operation. Children are often attracted to the

unit and mowing activity. Never assume that children will remain

where you last saw them. If there is a risk that children may enter

the area where you are mowing, have another responsible adult

watch them.

Slope Operation

You could be seriously injured or even killed if you use this unit on

too steep an incline. Using the unit on a slope that is too steep or

where you don’t have adequate footing or traction can cause you to

lose control or slip and fall.

You should not operate on inclines with a slope greater than 10

degrees, which is a 3.5 ft (1,5 m) rise over 20.0 ft (6,0 m). Always

mow across slopes, never up and down.

Also note that the surface you are mowing can greatly impact con-

trol. Wet grass or leaves can seriously affect your footing and trac-

tion on a slope.

If you feel unsure about operating the unit on an incline, don’t do it.

It’s not worth the risk.

20.0 ft

(6,0 m)

3.5 ft

(1,5 m)

Not for

Reproduction

Operator Safety

Moving Parts

This equipment has moving parts that can injure you or someone else.

However, if you stand behind the handle properly and follow all the rules in

this book, the unit is safe to operate.

The mower deck has a spinning mower blade that can amputate hands and

feet. Do not allow anyone near the equipment while it is running!

To help you, the operator, use this equipment safely, it is equipped with an

operator present safety system. Do NOT attempt to alter or bypass the sys-

tem. See your dealer immediately if the system does not pass all the safety

interlock system tests found in this manual.

Thrown Objects

This unit has a spinning mower blade. This blade can pick up and

throw debris that could seriously injure a bystander. Be sure to clean

up the area to be mowed BEFORE you start mowing.

Do not operate this unit without the entire grass catcher or discharge

guard (deflector) in place.

Also, do not allow anyone in the area while the unit is running! If

someone does enter the area, shut the unit off immediately until they

leave.

Debris Accumulation

Accumulation of grass and debris can result in a fire. Be sure to clean any

accumulation of grass and debris with a brush or compressed air, before

and after operation.

Fuel and Maintenance

Gasoline is extremely flammable. Its vapors are also extremely flam-

mable and can travel to distant ignition sources. Gasoline must only

be used as a fuel, not as a solvent or cleaner. It should never be

stored any place where its vapors can build up or travel to an ignition

source like a pilot light. Fuel belongs in an approved, plastic, sealed

gas can, or in the tractor fuel tank with the cap securely closed.

Spilled fuel needs to be cleaned up immediately.

Proper maintenance is critical to the safety and performance of your

unit. Be sure to perform the maintenance procedures listed in this

manual, especially periodically testing the safety system.

Not for

Reproduction

www.murray.com6

WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that

can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious

injury or death to the operator or other persons. The owner of the machine must understand these instructions

and must allow only persons who understand these instructions to operate machine. Each person operating

the machine must be of sound mind and body and must not be under the influence of any substance, which

might impair vision, dexterity or judgment. If you have any questions pertaining to your machine which your

dealer cannot answer to your satisfaction, contact the Customer Service Department (1-800-661-6662 or

www.murray.com).

Protection for Children

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

machine and the mowing activity. Never assume that

children will remain where you last saw them.

1. KEEP children out of the mowing area and under the

watchful care of a responsible adult other than the operator.

2. DO NOT allow children in yard when machine is operated

and turn machine OFF if anyone enters the area.

3. DO NOT allow pre-teenage children to operate machine.

4. ALLOW only responsible adults & teenagers with mature

judgment under close adult supervision to operate machine.

5. DO NOT pull mower backwards unless absolutely

necessary. LOOK and SEE behind and down for children,

pets and hazards before and while backing.

6. USE EXTRA CARE when approaching blind corners,

shrubs, trees, or other objects that may obscure vision.

Slope Operation

1. Slopes are a major factor related to slip and fall acci-

dents, which can result in severe injury. All slopes require

extra caution. If you feel uneasy on a slope, DO NOT mow

it.

2. Mow across slopes, never up-and-down. Exercise

extreme CAUTION when changing directions on slopes. DO

NOT mow steep slopes or other areas where stability or

traction is in doubt. Refer to the Slope Guide at the end of

this manual.

3. Use extra care with grass catchers or other attachments;

these affect the handling and the stability of the machine.

Preparation

1. Read, understand, and follow instructions and warnings

in this manual and on the mower, engine and attachments.

Know the controls and the proper use of the mower before

starting.

2. Only mature, responsible persons shall operate the

machine and only after proper instruction.

3. Data indicates that operators age 60 and above, are

involved in a large percentage of mower-related injuries.

These operators should evaluate their ability to operate the

mower safely enough to protect themselves and others

from serious injury.

Preparation

(Continued From Previous Column)

4. Handle fuel with extra care. Fuels are flammable and

vapors are explosive. Use only an approved fuel container.

DO NOT remove fuel cap or add fuel with engine running.

Add fuel outdoors only with engine stopped and cool. Clean

spilled fuel and oil from machine. DO NOT smoke.

5. Check the area to be mowed and remove all objects such

as toys, wire, rocks, limbs and other objects that could

cause injury if thrown by blade or interfere with mowing.

Also note the location of holes, stumps, and other possible

hazards.

6. Keep people and pets out of the mowing area.

Immediately, STOP Blade, Stop engine and Stop mower if

anyone enters the area.

7. Check shields, deflectors, switches, blade controls and

other safety devices frequently for proper operation and

location.

8. Make sure all safety decals are clearly legible. Replace if

damaged.

9. Protect yourself when mowing and wear safety glasses, a

dust mask, long pants, and substantial footwear. DO NOT

mow barefooted or with sandals.

10. Know how to STOP blade and engine quickly in

preparation for emergencies.

11. Use extra care when loading or unloading the machine

into a trailer or truck.

12. Check grass catcher components frequently for signs of

wear or deterioration and replace as needed to prevent

injury from thrown objects going through weak or torn

spots.

Safe Handling of Gasoline

To avoid personal injury or property damage, use extreme

care in handling gasoline. Gasoline is extremely flammable

and the vapors are explosive.

1. Extinguish all cigarettes, cigars, pipes and other sources

of ignition.

2. Use only an approved fuel container.

3. DO NOT remove fuel cap or add fuel with the engine

running. Allow the engine to cool before refueling.

4. DO NOT refuel the machine indoors.

5. DO NOT store the machine or fuel container inside where

there is an open flame, spark or pilot light such as on a

water heater or other appliances.

Operator Safety

Not for

Reproduction

Operator Safety

Safe Handling of Gasoline

(Continued From Previous Page)

6. DO NOT fill fuel containers inside a vehicle or on a truck

or trailer bed with a plastic liner. Always place the contain-

ers on the ground away from the vehicle before filling.

7. Remove gas-powered equipment from the vehicle or

trailer and refuel it on the ground. If this is not possible,

then refuel equipment using a portable container, rather

than a gasoline dispenser nozzle.

8. DO NOT start gas powered equipment in enclosed vehi-

cles or trailers.

9. Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. DO

NOT use a nozzle lock-open device

10. If fuel is spilled on clothing, change clothing

immediately.

11. DO NOT overfill a fuel tank. Replace fuel cap and tight-

en securely.

Operation

1. DO NOT put hands or feet near or under rotating parts.

Keep clear of discharge area while engine is running.

2. STOP engine when crossing gravel drives, walks, or

roads, and under any conditions where thrown objects

might be a hazard.

3. Mow only in daylight or good artificial light.

4. DO NOT operate mower while under the influence of

alcohol or drugs.

5. After striking a foreign object or if mower vibrates

abnormally, STOP the engine, disconnect and secure spark

plug wire. Inspect the mower for any damage and repair

the damage before starting.

6. DO NOT mow near drop offs, ditches or embankments.

Operator could lose footing or balance.

7. STAY ALERT for holes and other hidden hazards. Tall

grass can hide obstacles. Keep away from ditches,

washouts, culverts, fences and protruding objects.

8. DO NOT mow on wet grass. Always be sure of your

footing. Keep a firm hold on the handle and walk, never

run. Slipping could cause injury.

9. ALWAYS stay behind handle when engine (motor) is

running.

10. DO NOT leave the machine with the engine running.

STOP BLADE and STOP ENGINE before leaving the opera-

tors position for any reason.

11. Before cleaning, repairing or inspecting make certain

engine, blade and all moving parts have STOPPED.

Disconnect and secure spark plug wire away from plug to

prevent accidental starting.

12. STOP engine and wait until the blade comes to com-

plete STOP before removing grass bag and/or clearing

grass.

Operation

(Continued From Previous Column)

13. DO NOT operate mower without the entire grass catch-

er, or guards in place discharge guard, rear guard or other

safety devices in place and working. DO NOT point dis-

charge at people, passing cars, windows or doors.

14. DO NOT discharge material against a wall or obstruc-

tion. Material may ricochet back towards the operator.

15. Slow down before turning.

16. Watch out for traffic when near or crossing roadways.

17. DO NOT operate engine in enclosed areas. Engine

exhaust gases contain carbon monoxide, a deadly poison.

18. Only use accessories approved by the manufacturer.

See manufacturer’s instructions for proper operation and

installation of accessories.

Maintenance and Storage

1. DO NOT store mower or fuel container inside where

fumes may reach an open flame, spark or pilot light such as

in a water heater, furnace, clothes dryer or other gas appli-

ance. Allow engine to cool before storing machine in an

enclosure. Store fuel container out of reach of children in a

well ventilated, unoccupied building.

2. Keep mower and engine free of grass, leaves or excess

grease to reduce fire hazard and engine overheating.

3. When draining fuel tank, drain fuel into an approved

container outdoors and away from open flame.

4. Keep all bolts, especially blade bolts, nuts and screws

properly tight. Check that all cotter pins are in proper

position.

5. Always provide adequate ventilation when running

engine. Engine exhaust gases contain carbon monoxide, a

deadly poison.

6. Service engine and make adjustments only when engine

is stopped. Removed spark plug wire from spark plug and

secure wire away from spark plug to prevent accidental

starting.

7. DO NOT change engine governor speed settings or

overspeed engine.

8. Check grass bag assembly frequently for wear or

deterioration to avoid thrown objects and exposure to

moving parts. Replace with new bag if loose seams or tears

are evident. Replace slider or bag adapter if broken or

cracked.

9. Mower blades are sharp and can cut. Wrap the blades or

wear heavy leather gloves and use CAUTION when handling

them.

10. DO NOT test for spark by grounding spark plug next to

spark plug hole; spark plug could ignite gas exiting engine.

11. Have machine serviced by an authorized dealer at least

once a year and have the dealer install any new safety

devices.

12. Use only factory authorized replacement parts or like

parts when making repairs.

Not for

Reproduction

www.murray.com8

WARNING: Before doing any assembly or

maintenance to the mower, remove the wire

from the spark plug.

NOTE: In this instruction book, left and right describe the

location of a part with the operator standing behind the

handle.

Unpacking

The mower was fully assembled at the factory. When the

mower was put in the carton, the handle was put in the

storage position. To put the handle in the operating position,

follow the steps below.

Handle

1. Remove the mower from the carton.

2. Remove all packing material from the mower and the

handle.

3. MD22550FC - Raise the lower handle (A, Figure 1).

Make sure the lower handle is between the locking tabs

(B). Tighten the lower wingnuts (C).

M22550FC - Remove the wingnut (A, Figure 2) and bolt

(B) from each handle bracket (C). Raise the lower han-

dle (D), and secure with the removed bolt and wingnut.

4. Put the upper handle (D, Figure 1) in the operating

(upright) position. Tighten the upper wingnuts (E).

NOTE: The height of the handle can be set for operator

comfort. See “Handle Height”.

CAUTION: Be careful when you fold or raise the handle. Do

not damage the cables. A cable that is bent will not work

correctly. Before you use the unit, replace a bent or damaged

cable.

5. Hold the engine stop lever against the handle. (Refer to

section entitled ‘Engine Stop Lever’.) Slowly pull the

recoil-start grip (A, Figure 2). To attach the recoil-start

grip to the rope guide (B), twist the rope through the

rope guide mounted on the right side of the handle.

IMPORTANT: Operate the engine stop lever several times.

Make sure that the engine stop cable moves freely and that

the engine stop lever operates correctly.

Figure 1: Unfolding the handle (MD22550FC)

Figure 3: Attaching the recoil-start grip

Figure 2: Unfolding the handle (M22550FC)

Assembly

Not for

Reproduction

Handle Height (MD22550FC)

1. Remove the wingnuts (A, Figure 4) and bolts (B) from

the right and left handle brackets (C).

2. To raise the handle, mount the lower handle (A, Figure

5) in the high position (B).

3. To lower the handle, mount the lower handle in the low

position (C).

4. Attach the lower handle to the handle brackets with the

bolts and wingnuts removed in Step 1.

Handle Height (M22550FC)

1. Remove the wingnuts (A, Figure 6) and bolts (B) from

the right and left handle brackets (C).

Note: Do not remove the lower set of bolts and nuts securing

the lower handle.

2. To raise the handle, mount the lower handle (D, Figure

6) to a higher adjustment hole (E).

3. To lower the handle, mount the lower handle to a lower

adjustment hole.

4. Replace the bolts and wingnuts removed in Step 1,

tightening securely.

Figure 4: Removing the handle adjustment hardware

Figure 6: Handle positions (M22550FC)

Assembly

Figure 5: Handle positions (MD22550FC)

Not for

Reproduction

www.murray.com10

Assembling the Grass Bag (M22550FC)

Note: On some models, the side mounted discharge deflector

is temporarily attached (for shipping purposes) to the rear of

the mower. Before assembly of the grass bag, remove the

side mounted discharge deflector.

1. Slide the frame assembly (A, Figure 7) into the

grass bag (B).

2. Make sure the handle (A, Figure 8) is on the outside of

the grass bag.

3. First, attach the clips (B, Figure 8) to the side of the

frame assembly (C). Next, attach the clips to the top and

bottom of the frame assembly.

Mounting the Grass Bag (M22550FC)

1. To mount the grass bag on the mower, raise the rear

door (A, Figure 9). Holding the grass bag by the han-

dle (B), mount the hooks (C) on either end of the grass

bag frame assembly onto the rear door pivot rod (D).

Lower the grass bag against the rear of the mower.

Lower the rear door.

Important: Make sure both grass bag hooks are mounted on

the pivot rod.

WARNING: Check the condition of the grass

bag for wear or deterioration. If worn or

damaged, replace the parts only with

approved factory replacement parts.

Emptying the Grass Bag (M22550FC)

WARNING: Before you remove the grass bag,

stop the engine. Before you remove any grass

from the mower housing, disconnect the wire

from the spark plug.

1. Raise the rear door to a vertical position.

2. Hold the handle of the grass bag and lift the frame

assembly. Continue to lift the frame assembly until the

hooks are no longer mounted on the pivot rod. Remove

the grass bag.

3. Empty the grass from the grass bag.

4. To mount the grass bag on the mower, see “Mounting

The Grass Bag”.

Figure 7: Installing the frame assembly

Figure 8: Installing the bag clips

Figure 9: Mounting the grass bag

Assembly

Not for

Reproduction

Attaching the Mulching Plate

(MD22550FC)

WARNING: To prevent the engine from

starting, disconnect the wire from the

spark plug.

1. Raise the chute deflector (A, Figure 10).

2. Align the mulcher plate (B) with the side discharge

opening. Make sure that the two alignment bumps (C)

are inside the opening.

3. Mount the tab (D) on the top of the mulcher plate to the

inside of the mower housing.

4. Mount the tab (E) on the bottom of the mulcher plate to

the inside of the mower housing.

5. Lower the chute deflector.

6. Attach the wire to the spark plug.

Note: On some models, the mulcher kit is installed at the

factory. To convert from a mulcher to a side discharge,

simply remove the mulching plate.

Mulching Tips

Mulching finely cuts the grass so that the grass can be easily

recycled. Because the nutrients are returned to the soil, the

lawn will need less fertilizer. To correctly mulch the lawn,

follow the tips below.

• The grass must be dry. If the grass is wet, it will be

difficult to cut and cause heavy clumps of grass.

• The grass must not be too tall. The maximum height to

effectively cut is 4 1/2 inches. Set the height adjusters

so that only the top third of the grass is cut.

• If the grass is more than 4 1/2 inches high, two

mowings will be necessary. For the first mowing, set the

height adjusters in the highest position. Then, lower the

height adjusters for the second mowing.

• Keep a sharp edge on the blade. A blade that is not

sharp will cause the ends of the grass to become brown.

• Clean the underside of the mower housing. Grass and

other debris can keep the mower from working

correctly.

If the quality of cut is marginal, try the following:

• Set the height adjusters at a higher cutting height.

• Cut the grass more frequently.

• Operate the mower at a slower ground speed.

• Overlap the cutting swaths instead of cutting a full

swath with each pass.

• Mow across the marginal areas a second time.

Convert to Side Discharge

(M22550FC)

WARNING: To prevent the engine from

starting, disconnect the wire from the

spark plug.

1. Ensure the grass bag is removed.

2. Lift the mulching cover.

3. Slide the two tabs (A, Figure 11) on the side deflector

under the pivot pin.

4. Lower the side deflector. Make sure the locking tabs (B)

go through the slots in the side deflector.

5. Release the mulching cover (it will lay on top of the side

discharge deflector).

Assembly

Figure 10: Installing the mulcher plate

(MD22550FC)

Figure 11: Side deflector (M22550FC)

Not for

Reproduction

www.murray.com12

Assembly

How To Prepare The Engine

NOTICE: The engine does not contain oil. Before you start

the engine, make sure you add oil according to the instruc-

tions in this manual. If you start the engine without oil, it will

be damaged beyond repair and will not be covered under

warranty.

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality deter-

gent oils are acceptable if classified for service SF, SG, SH,

SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

* Below 40°F (4°C) the use of SAE 30 will result in hard

starting.

** Above 80°F (27°C) the use of 10W-30 may cause

increased oil consumption. Check oil level more frequently.

How To Check/Add Oil

Before adding or checking the oil

• Place engine level.

• Clean the oil fill area of any debris.

1. Remove the dipstick (A, Figure 12) and wipe with a

clean cloth.

2. Insert and tighten the dipstick.

3. Remove the dipstick and check the oil level. It should be

at the top of the full indicator (B) on the dipstick.

4. If low, add oil slowly into the engine oil fill (C). Do not

overfill. After adding oil, wait one minute and then

recheck the oil level.

5. Replace and tighten the dipstick.

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude

use, see below.

• Gasoline with up to 10% ethanol (gasohol) or up to

15% MTBE (methyl tertiary butyl ether) is acceptable.

CAUTION: Do not use unapproved gasolines, such as E85.

Do not mix oil in gasoline or modify the engine to run on

alternate fuels. This will damage the engine components and

void the engine warranty.

To protect the fuel system from gum formation, mix a fuel

stabilizer into the fuel. See Storage. All fuel is not the same.

If starting or performance problems occur, change fuel

providers or change brands. This engine is certified to oper-

ate on gasoline. The emissions control system for this

engine is EM (Engine Modifications).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85

octane/85 AKI (89 RON) gasoline is acceptable. To remain

emissions compliant, high altitude adjustment is required.

Operation without this adjustment will cause decreased per-

formance, increased fuel consumption, and increased emis-

sions. See a Briggs & Stratton Authorized Dealer for high

altitude adjustment information.

Operation of the engine at altitudes below 2,500 feet (762

meters) with the high altitude kit is not recommended.

Figure 12: Engine oil

Not for

Reproduction

Assembly

How To Add Fuel

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

When Adding Fuel:

• Turn engine off and let engine cool at least 2 minutes

before removing the fuel cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank. To allow for expansion of the

fuel, do not fill above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap, and fittings frequently for

cracks or leaks. Replace if necessary.

• If fuel spills, wait until it evaporates before starting

engine.

1. Clean the fuel cap area of dirt and debris. Remove the

fuel cap (A, Figure 13).

2. Fill the fuel tank (B) with fuel. To allow for expansion of

the fuel, do not fill above the bottom of the fuel tank

neck (C).

3. Reinstall the fuel cap.

IMPORTANT: This unit is equipped with an internal

combustion engine and must not be used on or near any

unimproved forest-covered, brush-covered or grass-covered

and unless the engine’s exhaust system is equipped with a

spark arrester meeting applicable local or state laws (if any).

If a spark arrester is used, it must be maintained in effective

working order by the operator.

In the State of California the above is required by law

(Section 4442 of the California Public Resources Code).

Other states may have similar laws. Federal laws apply on

federal lands. See an Authorized Service Center for a spark

arrester for the muffler.

Final Preparation

Before you use the mower, check the assembly of the

wheels, the handle, and the controls. Make sure all the

fasteners are tight. Make sure the throttle control (if

equipped) and the engine stop lever work correctly.

Before starting the engine, make sure each height adjuster is

set at the desired height. See “Adjusting The Height Of Cut”

in the Operation section.

Figure 13: Adding fuel

Not for

Reproduction

www.murray.com14

Engine Stop Lever

Release the engine stop lever (A, Figure 14) and the engine

and the blade will automatically stop. To run the engine, hold

the engine stop lever in the Operating position (B).

Before you start the engine, operate the engine stop lever

several times. Make sure the cable moves easily.

How to Stop the Engine

To stop the engine, release the engine stop lever. Disconnect

the wire from the spark plug to prevent the engine from

starting.

Before you start the engine, check the engine stop cable.

Make sure the engine stop cable is assembled correctly.

Before you operate the unit, replace a bent or damaged

engine stop cable.

How To Start The Engine

WARNING: The blade will rotate when the

engine runs.

WARNING

Rapid retraction of starter cord (kickback) will

pull hand and arm toward engine faster than you

can let go.

Broken bones, fractures, bruises or sprains

could result.

• When starting engine, pull the starter cord slowly until

resistance is felt and then pull rapidly to avoid kickback.

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

When Starting Engine

• Ensure that spark plug, muffler, fuel cap and air cleaner

(if equipped) are in place and secured.

• Do not crank engine with spark plug removed.

• If engine floods, set choke (if equipped) to OPEN/RUN

position, move throttle (if equipped) to FAST position

and crank until engine starts.

WARNING

Engines give off carbon monoxide, an odorless,

colorless, poison gas.

Breathing carbon monoxide can cause nausea,

fainting or death.

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if

doors or windows are open.

Important: Before you start the engine, operate the engine

stop lever several times. Make sure that the engine stop

cable moves freely and that the engine stop lever operates

correctly.

1. Check the oil. See “How To Prepare The Engine”.

2. Fill the fuel tank. See “How To Prepare The Engine”.

3. Engines with primer: For most temperature conditions,

firmly push the primer bulb (A, Figure 15) three times.

In cooler weather, additional priming may be needed. A

warm engine will usually not require priming. Every time

you push the primer button, wait two seconds. Note:

When starting a new engine for the first time, push the

primer bulb five times.

Note: Excessive priming can flood the carburetor with

fuel. See “The Engine Will Not Start” in the

Troubleshooting section.

Figure 14: Operating the engine stop lever

Figure 15: Primer bulb

Operation

Not for

Reproduction

4. Stand behind the mower. Use one hand to hold the

engine stop lever (A, Figure 16) in the operating posi-

tion. Use the other hand to hold the recoil starter handle

(B).

5. Slowly pull the recoil starter handle until resistance is

felt, then pull quickly to start the engine. Slowly return

the recoil starter handle.

6. If the engine does not start in 5 or 6 tries, see the

Troubleshooting section.

Rules for Safe and Effective Operation

Refer to the ‘Operator Safety’ section of this manual for

important rules concerning safe and effective mower

operation.

Adjusting the Height of Cut

WARNING: The blade will rotate when the

engine runs. Before you change the height of

cut, stop the engine and disconnect the wire

from the spark plug.

To change the height of cut, move the position of the

adjuster arm at each wheel (A, Figure 17). Make sure each

adjuster arm is in the same position so that the mower will

cut level.

1. Disengage the adjuster arm.

2. Move the adjuster arm to another position.

Figure 16: Starting the engine

Operation

Figure 17: Adjusting the height of cut

Not for

Reproduction

www.murray.com16

Maintenance

Maintenance Chart

WARNING: Before you make an inspection,

adjustment (except carburetor), or repair, stop

the engine and disconnect the wire from the

spark plug.

MOWER

Every 8 Hours or Daily

Check safety interlock system

Clean debris off mower

Every 25 Hours or Annually *

Check mower for loose hardware

See Dealer Annually to

Lubricate mower

Check mower blade **

Check mower blade stopping time

ENGINE

First 5 Hours

Change engine oil

Every 8 Hours or Daily

Check engine oil level

Every 25 Hours or Annually *

Clean engine air filter and pre-cleaner (if equipped) **

Every 50 Hours or Annually *

Change engine oil

Replace oil filter (if equipped)

Annually

Replace air filter

Replace pre-cleaner (if equipped)

See Dealer Annually to

Inspect muffler and spark arrester (if equipped)

Replace spark plug

Replace fuel filter (if equipped)

Clean engine air cooling system

* Whichever comes first

**Check blades more often in regions with sandy soils or

high dust conditions.

* Whichever comes first

**Clean more often in dusty conditions or when airborne

debris is present.

Not for

Reproduction

Mower Maintenance

Emissions Control

Maintenance, replacement, or repair of the emissions control

devices and systems may be performed by any non-road

engine repair establishment or individual. However, to obtain

“no charge” emissions control service, the work must be

performed by a factory authorized dealer. See the Emissions

Warranty.

WARNING: Before you make an inspection,

adjustment (except carburetor), or repair, stop

the engine and disconnect the wire from the

spark plug.

Engine Tipping

When you service the engine, inspect the blade, or clean the

underside of the mower housing; make sure to always tip the

engine with the spark plug up (Figure 18). Transporting or

tipping the engine with the spark plug down will cause:

• Hard starting.

• Engine smoking.

• Spark plug fouling.

• Oil or gas saturation of the air filter.

Check Safety Interlock System

1. Start the mower.

2. Release the engine stop lever. The engine must stop

within 3 seconds.

If the engine does not stop, do not use the mower. Bring the

mower to an authorized dealer for service.

Cleaning the Mower Housing

WARNING: The blade will rotate when the

engine runs. Before you clean the mower

housing, stop the engine and disconnect the

wire from the spark plug.

Grass and other debris can keep the mower from working

correctly. After you mow, clean the mower housing as

follows.

1. Stop the engine.

2. Disconnect the wire from the spark plug.

3. Clean dirt and debris from the top and the bottom of the

mower housing.

Lubrication

For maximum performance, lubricate the wheels and all pivot

points with engine oil every 25 hours.

Note: Do not lubricate the engine stop cable. Lubricants will

damage the cable and prevent the cable from moving freely.

Replace the cable if bent or damaged.

Figure 18: No forward engine tipping

Maintenance

Not for

Reproduction

www.murray.com18

Blade Service

WARNING: Before you inspect the blade or the

blade adapter, disconnect the wire to the

spark plug. If the blade hits an object, stop the

engine. Disconnect the wire to the spark plug.

Check the unit for damage.

Frequently check the blade for wear or damage such as

cracks. Frequently check the bolt that holds the blade. Keep

the bolt tight. If the blade hits an object, stop the engine.

Disconnect the wire to the spark plug. Check the blade

adapter (A, Figure 19) for damage. Check for a bent or

damaged blade, a badly worn blade, or other damage. Before

you operate the unit, damaged parts must be replaced with

factory replacement parts. For safety, replace the blade every

two years. Keep a sharp edge on the blade. A blade that is

not sharp will cause the ends of the grass to become brown.

Remove the blade as follows.

Removing the Blade

WARNING: Before you remove the blade,

disconnect the wire to the spark plug. The

blade has sharp edges. When you hold the

blade, use gloves or cloth material to protect

your hands.

1. Drain the fuel tank.

2. Lift the side of the mower that has the muffler or spark

plug.

3. Use a piece of wood to keep the blade from rotating.

4. Remove the bolt (B, Figure 19) that holds the blade

with a 9/16” (14mm) wrench.

5. Check the blade (C) according to the “Blade Service”

instructions. Replace a badly worn or damaged blade

with a factory replacement blade.

6. Mount the blade with the curved edges toward the

housing. If the blade is upside down, the blade will not

cut correctly and can cause an accident.

7. Fasten the blade with the original washer (D) and bolt.

Make sure the outside rim of the Belleville washer is

toward the blade.

8. Tighten the bolt that holds the blade to a torque of 30

foot pounds.

WARNING: Always keep the bolt that holds the

blade tight. A loose bolt or blade can cause an

accident.

Sharpening the Blade

WARNING: Vibration is the result if the blade

is not correctly balanced. A blade that is

damaged with cracks can break and cause

an accident.

1. Sharpen the blade two times a year or every 25 hours.

2. If the blade is on the unit, do not sharpen. Remove the

blade according to the instructions in “Removing The

Blade”.

3. Clean the blade with a brush, soap, and water. Check the

blade. Look for cracks, nicks, or other damage. Replace

a blade that is badly worn, bent, or damaged with a

factory replacement blade.

4. Sharpen the blade (A, Figure 20) with a file (B). Make

sure you keep the original beveled cutting edge.

5. Make sure the blade is balanced. Use a screwdriver (C)

and hold the blade parallel to the ground (D) as shown.

A blade that is balanced will stay parallel to the ground.

If the blade is not balanced, the heavy end will rotate

toward the ground. Sharpen the heavy end until the

blade is balanced.

6. A new blade will cut better than a badly worn blade.

Every two years replace the old blad6.

Checking the Level of Cut

Test the unit in a small area. If the height of cut is not level

or if the cut grass is not discharged, the cause can be: (1)

the blade is bent or damaged, (2) the blade is not sharp, (3)

a worn blade, (4) or a broken blade adapter. Before you use

the unit, correct the problem.

Figure 19: Removing the blade

Maintenance

Not for

Reproduction

Maintenance

Engine Maintenance

Carburetor Adjustment

Never make adjustments to the carburetor. The carburetor

was set at the factory to operate efficiently under most con-

ditions. However, if adjustments are required, see any Briggs

& Stratton Authorized Dealer for service.

How To Change The Oil

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

• If you drain the oil from the top oil fill tube, the fuel tank

must be empty or fuel can leak out and result in a fire or

explosion.

Used oil is a hazardous waste product and must be disposed

of properly. Do not discard with household waste. Check

with your local authorities, service center, or dealer for safe

disposal/recycling facilities.

Remove Oil

You can drain the oil from the bottom drain hole, the side

drain hole, or from the top oil fill tube.

1. With engine off but still warm, disconnect the spark plug

wire and keep it away from the spark plug.

2. The engine is equipped with a bottom drain and/or a

side drain. Remove the oil drain plug. Drain the oil into

an approved container.

3. After the oil has drained, install and tighten the oil drain

plug.

4. If you drain the oil from the top oil fill tube (C, Figure

21), keep the spark plug end of the engine up. Drain the

oil into an approved container.

WARNING: If you drain the oil from the top oil

fill tube, the fuel tank must be empty or fuel can

leak out and result in a fire or explosion. To

empty the fuel tank, run the engine until it stops

from lack of fuel.

Add Oil

• Place engine level.

• Clean the oil fill area of any debris.

1. Remove the dipstick (A, Figure 21) and wipe with a

clean cloth.

2. Pour the oil slowly into the engine oil fill (C). Do not

overfill. After adding oil, wait one minute and then check

the oil level.

3. Install and tighten the dipstick.

4. Remove the dipstick and check the oil level. It should be

at the top of the full indicator (B) on the dipstick.

5. Install and tighten the dipstick.

Figure 20: Sharpening the blade

Figure 21: Engine oil

Not for

Reproduction

www.murray.com20

Maintenance

How To Service The Air Filter

NOTICE: Do not use pressurized air or solvents to clean the

filter. Pressurized air can damage the filter and solvents will

dissolve the filter.

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

• Never start or run the engine with the air cleaner assem-

bly (if equipped) or the air filter (if equipped) removed.

1. Open the cover (A, Figure 22) and remove the filter (B).

2. Gently tap the filter on a hard surface. If the filter is

excessively dirty, replace with a new filter.

3. Install the filter and close the cover.

Storage

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

When Storing Fuel Or Equipment With Fuel In Tank

• Store away from furnaces, stoves, water heaters or

other appliances that have pilot lights or other ignition

sources because they can ignite fuel vapors.

Fuel System

Fuel can become stale when stored over 30 days. Stale fuel

causes acid and gum deposits to form in the fuel system or

on essential carburetor parts. To keep fuel fresh, use Briggs

& Stratton FRESH START® fuel stabilizer, available as a liq-

uid additive or a drip concentrate cartridge.

There is no need to drain gasoline from the engine if a fuel

stabilizer is added according to instructions. Run the engine

for 2 minutes to circulate the stabilizer throughout the fuel

system. The engine and fuel can then be stored up to 24

months.

If gasoline in the engine has not been treated with a fuel sta-

bilizer, it must be drained into an approved container. Run

the engine until it stops from lack of fuel. The use of a fuel

stabilizer in the storage container is recommended to main-

tain freshness.

Engine Oil

While the engine is still warm, change the engine oil.

How To Prepare The Mower For Storage

1. Clean the dirt and debris from the cylinder cooling fins

and the engine housing.

2. Clean the bottom of the mower housing.

3. Completely clean the mower to protect the paint.

4. Put the unit in a building that has good ventilation.

5. Make sure the grass bag is empty of grass. Grass remain-

ing in the bag during storage will damage the bag.

6. Fold the handles (if desired).

CAUTION: Be careful when you fold or raise the handle. Do

not damage the cables. A cable that is bent will not work

correctly. Before you use the unit, replace a bent or damaged

cable.

NOTICE: Store the engine level (normal operating position).

If the engine is tipped for storage, the fuel tank must be

empty and the spark plug side must be up. If the fuel tank is

not empty and if the engine is tipped in any other direction, it

may be difficult to start due to oil or gasoline contaminating

the air filter and/or the spark plug.

Figure 22: Air filter

Not for

Reproduction

La page est en cours de chargement...

Murray 7800889 Manuel utilisateur

Marque: Murray

Modèle: 7800889

Catégorie: Tondeuses à gazon

Taper: Manuel utilisateur

Ce manuel convient également à

7800890

Télécharger le PDF

rapport

dans d''autres langues

English: Murray 7800889 User manual

Murray 7800889 Manuel utilisateur

Ce manuel convient également à

Murray 7800889 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents