Sony XM554ZR - XM Amplifier Manuel utilisateur
- Taper
- Manuel utilisateur
1
SERVICE MANUAL
US Model
Canadian Model
E Model
XM-554ZR
STEREO POWER AMPLIFIER
Circuit system OTL (output transformerless) circuit
Pulse power supply
Inputs RCA pin jacks
High level input connector
Input level adjustment range
0.3 – 6 V (RCA pin jacks),
2.8 – 12 V (High level input)
Outputs Speaker terminals
Speaker impedance 2 – 8 Ω (stereo)
4 – 8 Ω (when used as a bridging amplifier)
Maximum output 4 speakers: 110 W × 4 (at 4 Ω)
3 speakers: 150 W × 2 (at 2 Ω) + 300 W × 1 (BTL, at 4 Ω)
Rated output (supply voltage at 14.4 V)
4 speakers:
55 W × 4 (20 Hz – 20 kHz, 0.04% THD, at 4 Ω)
65 W × 4 (20 Hz – 20 kHz, 0.1% THD, at 2 Ω)
Frequency response 5 Hz – 50 kHz ( dB)
Harmonic distortion 0.005% or less (at 1 kHz, 4 Ω)
Low-pass filter 80 Hz, –18 dB/oct
High-pass filter 80 Hz, –12 dB/oct
Power requirements 12 V DC car battery (negative ground)
Power supply voltage 10.5 – 16 V
Current drain at rated output : 30 A (4 Ω, 55 W × 4)
Remote input : 1 mA
Dimensions Approx. 401 × 55 × 264 mm (w/h/d)
not incl. projecting parts and controls
Mass Approx. 3.2 kg not incl. accessories
Supplied accessories Mounting screws (4)
High level input cord (1)
Protection cap (1)
Design and specifications are subject to change without
notice.
SPECIFICATIONS
+0
–3
Ver. 1.2 2006. 08
9-887-093-03
2006H04-1
© 2006. 08
Sony Corporation
eVehicle Division
Published by Sony Techno Create Corporation
2
TABLE OF CONTENTS
1. GENERAL
Location and Function of Controls.......................................... 3
Connections ............................................................................. 4
2. DISASSEMBLY
2-1. Bottom Plate........................................................................ 7
2-2. AMP Board Section ............................................................ 8
2-3. Panel (Front)........................................................................ 8
3. DIAGRAMS
3-1. Block Diagram .................................................................... 9
3-2. Printed Wiring Board ........................................................11
3-3. Schematic Diagram –AMP Section (1/2)–........................12
3-4. Schematic Diagram –AMP Section (2/2)–........................13
4. EXPLODED VIEWS
4-1. Heat Sink (Main) Section.................................................. 15
4-2. AMP Board Section .......................................................... 16
5. ELECTRICAL PARTS LIST ........................................ 17
XM-554ZR
PROTECTOR OPERATION CHECK
Thermal Protect
1. Short across TH901 with the power on.
2. Verify that the protector is operated and LED901 illuminates
red.
3. Ve rify that the protector is released and LED901 illuminates green
when the short is removed.
4. Likewise, perform items 1 to 3 for TH902 and TH903.
Over Current Protect
1. Short between the positive and negative sides of the speaker
output terminals CN903 and CN904 with the power on.
(Perform this shorting for each channel on FRONT and REAR.)
2. Verify that the protector is operated and LED901 illuminates
red.
3. Verify that the protector is not released and LED901 remains
red even when the short is removed.
4. Ve rify that the protector is released and LED901 illuminates green
when the power is turned off and then on again.
Offset Protect
1. Short between the +12V terminal of CN905 and the (L+R) + or
(L+R) – of the speaker output terminal CN904.
(Short between +12V terminal and (L+R) + and between +12V
terminal and (L+R) –.)
2. Verify that the protector is operated and LED901 illuminates
red.
3. Verify that the protector is not released and LED901 remains
red even when the short is removed.
4. Ve rify that the protector is released and LED901 illuminates green
when the power is turned off and then on again.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
Notes on Chip Component Replacement
•Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Ver. 1.1
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
3
XM-554ZR
SECTION 1
GENERAL
This section is extracted
from instruction manual.
Location and Function of Controls
Emplacement et fonction des commandes
Ubicación y función de los controles
POWER/
PROTECTO
R
1 POWER/PROTECTOR indicator
Lights up in green during operation.
When the PROTECTOR is activated the
indicator will change from green to red.
When the PROTECTOR is activated refer to
the Troubleshooting Guide.
2 LEVEL adjustment control
The input level can be adjusted with this
control. Turn it in the clockwise direction
when the output level of the car audio unit
seems low.
3 HPF switch
When the HPF switch is set to ON, the
High-
pass filter
(80 Hz) is effective.
4 LPF switch
When the LPF switch is set to ON, the
Low-
pass filter
(80 Hz) is effective.
1 Indicateur POWER/PROTECTOR
S’allume en vert en cours de fonctionnement.
Lorsque PROTECTOR est activé, l’indicateur
passe du vert au rouge.
Lorsque PROTECTOR est activé, reportez-
vous au Guide de dépannage.
2 Commande de réglage LEVEL
Le niveau d’entrée peut se régler avec cette
commande. Tournez cette commande dans le
sens des aiguilles d’une montre lorsque le
niveau de sortie de l’autoradio semble faible.
3 Commutateur HPF
Lorsque le commutateur HPF est réglé sur
ON, le filtre passe-haut (80 Hz) est activé.
4 Commutateur LPF
Lorsque le commutateur LPF est réglé sur
ON, le filtre passe-bas (80 Hz) est activé.
1 Indicador POWER/PROTECTOR
Se ilumina en verde durante el uso.
Si se activa PROTECTOR, el indicador
cambiará de verde a rojo.
Si se activa PROTECTOR, consulte la Guía de
solución de problemas.
2 Control de ajuste LEVEL
Mediante este control se puede ajustar el
nivel de entrada. Gírelo en el sentido de las
agujas del reloj si el nivel de salida del
sistema de audio para automóvil parece bajo.
3 Interruptor HPF
Cuando el interruptor HPF está ajustado en
ON, se activa el filtro de paso alto (80 Hz).
4 Interruptor LPF
Cuando el interruptor LPF está ajustado en
ON, se activa el f
iltro de paso bajo
(80 Hz).
(80Hz)
LPF
LEVEL
REAR
OFF ON
1
2
4
60.3V
0.5
(80Hz)
HPF
LEVEL
FRONT
OFF ON
1
2
4
6 0.3V
0.5
Precautions
• This unit is designed for negative ground 12 V
DC operation only.
• Use speakers with an impedance of 2 to 8 Ω (4
to 8 Ω when used as a bridging amplifier).
• Do not connect any active speakers (with built-
in amplifiers) to the speaker terminals of the
unit. Doing so may damage the active speakers.
• Avoid installing the unit in areas subject to:
—high temperatures such as from direct
sunlight or hot air from the heater
— rain or moisture
— dust or dirt.
•If your car is parked in direct sunlight and there
is a considerable rise in temperature inside the
car, allow the unit to cool down before use.
• When installing the unit horizontally, be sure
not to cover the fins with the floor carpet etc.
•If this unit is placed too close to the car audio
unit or aerial, interference may occur. In this
case, relocate the amplifier away from the car
audio unit or aerial.
•If no power is being supplied to the car audio
unit, check the connections.
• This power amplifier employs a protection
circuit* to protect the transistors and speakers if
the amplifier malfunctions. Do not attempt to
test the protection circuits by covering the heat
sink or connecting improper loads.
• Do not use the unit on a weak battery as its
optimum performance depends on a good
power supply.
• For safety reasons, keep your car audio unit
volume moderate so that you can still hear
sounds outside your car.
Fuse Replacement
If the fuse blows, check the power connection
and replace both the fuses. If the fuse blows
again after replacement, there may be an internal
malfunction. In such a case, consult your nearest
Sony dealer.
Warning
When replacing the fuse, be sure to use one matching
the amperage stated above the fuse holder. Never use a
fuse with an amperage rating exceeding the one
supplied with the unit as this could damage the unit.
*
Protection circuit
This amplifier is provided with a protection circuit
that operates in the following cases:
— when the unit is overheated
— when a DC current is generated
— when the speaker terminals are short-circuited.
The colour of the POWER/PROTECTOR indicator
will change from green to red, and the unit will
shut down.
If this happens, turn off the connected equipment,
take out the cassette tape or disc, and determine
the cause of the malfunction. If the amplifier has
overheated, wait until the unit cools down before
use.
If you have any questions or problems
concerning your unit that are not covered in this
manual, please consult your nearest Sony dealer.
Précautions
• Cet appareil est conçu pour fonctionner
uniquement sur un courant de 12 V CC avec
masse négative.
•Utilisez des haut-parleurs d’une impédance
appropriée de 2 à 8 Ω (stéréo), 4 à 8 Ω (en cas
d’utilisation comme amplificateur en pont).
• Ne raccordez pas de haut-parleurs actifs (avec
amplificateurs intégrés) aux bornes des haut-
parleurs de cet appareil. Cela risquerait en effet
d’endommager les haut-parleurs actifs.
• N’installez pas l’appareil dans des endroits
soumis :
— à des températures élevées, comme en plein
soleil ou près du chauffage ;
— à la pluie ou à l’humidité ;
— à la poussière ou à la saleté.
•Si votre voiture est garée en plein soleil et que
la température a considérablement augmenté à
l’intérieur de l’habitacle, laissez l’appareil
refroidir avant de l’utiliser.
•Si vous installez l’appareil à l’horizontale, ne
recouvrez pas les ailettes de ventilation avec le
tapis de sol ou quoi que ce soit d’autre.
•Si cet appareil est placé trop près de l’autoradio
ou de l’antenne, il se peut que des interférences
se produisent. Dans ce cas, éloignez
l’amplificateur de l’autoradio ou de l’antenne.
•Si l’autoradio n’est pas alimenté, vérifiez les
connexions.
• Cet amplificateur de puissance est équipé d’un
circuit de protection * conçu pour protéger les
transistors et les haut-parleurs en cas de
défaillance de l’amplificateur. N’essayez pas de
tester l’efficacité des circuits de protection en
recouvrant le dissipateur thermique ou en
effectuant de mauvaises connexions.
• N’utilisez pas l’appareil avec une batterie faible,
car sa performance optimale dépend d’une
bonne alimentation en électricité.
• Pour des raisons de sécurité, maintenez le
volume de l’autoradio à un niveau modéré afin
d’entendre les bruits extérieurs.
Remplacement du fusible
Si le fusible fond, vérifiez les connexions de
l’alimentation et remplacez le fusible. Si le fusible
fond de nouveau après avoir été remplacé, cela
peut révéler une défaillance interne de l’appareil.
Dans ce cas, consultez votre distributeur Sony le
plus proche.
Avertissement
Lorsque vous remplacez le fusible, veillez à
utiliser un fusible dont la capacité en ampères
correspond à celle inscrite sur le porte-fusible.
N’utilisez jamais de fusible dont la capacité
dépasse celle du fusible fourni avec l’appareil car
cela pourrait endommager l’appareil.
*
Circuit de protection
Cet amplificateur est fourni avec un circuit de
protection qui entre en fonction dans les cas suivants :
— lorsque l’appareil est en surchauffe ;
— lorsqu’un courant continu est généré ;
— lorsque les bornes de haut-parleur sont court-
circuitées.
La couleur de l’indicateur POWER/PROTECTOR passe
du vert au rouge et l’appareil se met hors tension.
Dans ce cas, éteignez les appareils raccordés, retirez
la cassette ou le disque et déterminez l’origine du
problème. Si l’amplificateur est en surchauffe,
attendez qu’il refroidisse avant d’utiliser l’appareil.
Si vous avez des questions ou des problèmes
concernant votre appareil qui ne sont pas
abordés dans ce mode d’emploi, adressez-vous à
votre distributeur Sony le plus proche.
Sustitución del fusible
Si el fusible se funde, compruebe la conexión de
alimentación y sustituya ambos fusibles. Si el
fusible se funde de nuevo después de sustituirlo,
es posible que exista un fallo de funcionamiento
interno. En este caso, póngase en contacto con el
distribuidor Sony más próximo.
Advertencia
Al sustituir el fusible, asegúrese de utilizar uno
cuyo amperaje coincida con el especificado en el
portafusible. No utilice nunca un fusible con un
amperaje superior al del suministrado con la
unidad, ya que podría dañar la unidad.
*
Circuito de protección
Este amplificador dispone de un circuito de
protección que se activa en los siguientes casos:
—Si la unidad se calienta excesivamente
—Si se genera corriente cc
—Si los terminales de altavoz se cortocircuitan.
El color del indicador POWER/PROTECTOR
cambiará de verde a rojo y la unidad se
desactivará.
Si esto ocurre, desactive el equipo conectado,
extraiga la cinta de casete o el disco y determine la
causa del fallo de funcionamiento. Si el
amplificador se ha sobrecalentado, espere hasta
que la unidad se enfríe antes de volver a utilizarla.
Si desea realizar alguna consulta o solucionar
algún problema relativos a la unidad que no
aparezcan en este manual, póngase en contacto
con el distribuidor Sony más próximo.
Precauciones
• Esta unidad está diseñada para utilizarse sólo
con cc de 12 V negativo a masa.
• Emplee altavoces con impedancia de 2 a 8 Ω (de
4 a 8 Ω cuand se utilice como amplificador en
puente).
• No conecte altavoces activos (con
amplificadores incorporados) a los terminales
de altavoz de la unidad, ya que puede dañar
dichos altavoces.
• Evite instalar la unidad en lugares expuestos a:
—altas temperaturas, como a la luz solar
directa o al aire caliente de la calefacción
—la lluvia o la humedad
— suciedad o polvo.
•Si aparca el automóvil bajo la luz solar directa y
se produce un considerable aumento de
temperatura en el interior, deje que la unidad se
enfríe antes de utilizarla.
•Si instala la unidad horizontalmente, asegúrese
de no cubrir las aletas con la moqueta del suelo,
etc.
•Si coloca la unidad demasiado cerca del sistema
de audio para automóvil o de la antena, pueden
producirse interferencias. En este caso, instale
el amplificador alejado de dichos dispositivos.
•Si el sistema de audio para automóvil no recibe
alimentación, compruebe las conexiones.
• Este amplificador de potencia emplea un
circuito de protección * para proteger los
transistores y los altavoces en caso de que dicho
amplificador presente fallos de funcionamiento.
No intente someter a prueba los circuitos de
protección cubriendo el disipador de calor o
conectando cargas inadecuadas.
• No utilice la unidad si la batería se está
agotando, ya que el rendimiento óptimo de
dicha unidad depende de un buen suministro
de alimentación.
• Por razones de seguridad, mantenga el
volumen del sistema de audio para automóvil
en un nivel moderado de forma que sea posible
oír los sonidos del exterior del automóvil.
4
XM-554ZR
Installation
Instalación
1
Installation
Mount the unit as illustrated.
Montez l’appareil comme illustré.
Monte la unidad tal como se muestra
en la ilustración.
Before Installation
• Mount the unit either inside the trunk or under
a seat.
• Choose the mounting location carefully so the
unit will not interfere with the normal
movements of the driver and it will not be
exposed to direct sunlight or hot air from the
heater.
• Do not install the unit under the floor carpet,
where the heat dissipation from the unit will be
considerably impaired.
First, place the unit where you plan to install it,
and mark the positions of the 4 screw holes on
the mounting board (not supplied). Then drill a 3
mm (
1
/ 8 in) pilot hole at each mark and mount
the unit onto the board with the supplied
mounting screws. The mounting screws are all
15 mm (
19
/ 32 in) long, so make sure that the
mounting board is thicker than 15 mm (
19
/ 32 in).
Avant l’installation
• Installez l’appareil dans le coffre ou sous un
siège.
• Choisissez soigneusement l’emplacement de
montage afin d’éviter que l’appareil ne gêne le
conducteur dans ses mouvements et qu’il ne
soit pas exposé au rayonnement direct du soleil
ou à l’air chaud du radiateur.
• N’installez pas l’appareil sous le tapis de sol car
la dissipation thermique ne pourrait pas se faire
correctement.
Posez d’abord l’appareil à l’endroit où vous
souhaitez l’installer et tracez un repère de
positionnement pour les 4 orifices de vis sur la
plaque de montage (non fournie). Percez des
orifices de 3 mm (
1
/ 8 po) au niveau de chaque
repère et fixez l’appareil sur la plaque avec les vis
de montage fournies. La longueur des vis de
montage est de 15 mm (
19
/ 32 po). Assurez-vous
donc que l’épaisseur de la plaque de montage est
supérieure à 15 mm (
19
/ 32 po).
Antes de realizar la instalación
• Monte la unidad en el interior del maletero o
debajo de un asiento.
• Elija cuidadosamente el lugar de instalación de
forma que la unidad no dificulte las maniobras
normales del conductor y no quede expuesta a
la luz solar directa ni al aire caliente de la
calefacción.
• No instale la unidad debajo de la moqueta del
suelo, en cuyo caso la disipación de calor de la
misma disminuirá considerablemente.
En primer lugar, coloque la unidad donde tenga
previsto instalarla y marque sobre la superficie
del tablero de montaje (no suministrado) las
posiciones de los 4 orificios para los tornillos. A
continuación, perfore los orificios con un
diámetro de aproximadamente 3 mm y monte la
unidad sobre el tablero con los tornillos de
montaje suministrados. Ya que la longitud de
estos tornillos es de 15 mm, compruebe que el
grosor del tablero de montaje sea superior a 15
mm.
Avertissement
Cautions
Precaución
• Before making any connections, disconnect the
ground terminal of the car battery to avoid
short circuits.
• Be sure to use speakers with an adequate power
rating. If you use small capacity speakers, they
may be damaged.
• This is a Phase-Inverted Amplifier.
• Do not connect the # terminal of the speaker
system to the car chassis, and do not connect
the # terminal of the right speaker with that of
the left speaker.
• Install the input and output cords away from
the power supply wire as running them close
together can generate some interference noise.
• This unit is a high powered amplifier.
Therefore, it may not perform to its full
potential if used with the speaker cords
supplied with the car.
• If your car is equipped with a computer system
for navigation or some other purpose, do not
remove the ground wire from the car battery. If
you disconnect the wire, the computer memory
may be erased. To avoid short circuits when
making connections, disconnect the +12 V
power supply wire until all the other wires
have been connected.
• Avant d’effectuer les raccordements,
débranchez la borne de masse de la batterie de
voiture pour éviter de provoquer un court-
circuit.
• Utilisez des haut-parleurs d’une capacité
adéquate. Si vous utilisez des haut-parleurs de
faible capacité, ils risquent d’être endommagés.
• Les phases de cet amplificateur sont inversées.
• Ne raccordez pas la borne # du système de
haut-parleurs à la carrosserie de la voiture, ou
la borne # du haut-parleur droit à celle du
haut-parleur gauche.
• Eloignez les cordons d’entrée et de sortie du fil
d’alimentation électrique afin d’éviter que des
interférences ne se produisent.
• Cet appareil est un amplificateur de haute
puissance. Il se peut donc qu’il n’atteigne pas sa
puissance maximale s’il est utilisé avec les
cordons de haut-parleurs de la voiture.
• Si votre voiture est équipée d’un ordinateur de
bord pour la navigation ou autre, ne débranchez
pas le fil de masse de la batterie de la voiture. Si
vous débranchez ce fil, toute la mémoire de
l’ordinateur risque d’être effacée. Pour éviter
tout risque de court-circuit lorsque vous
effectuez les raccordements, branchez le fil
d’alimentation de +12 V uniquement après
avoir branché tous les autres fils.
• Antes de realizar las conexiones, desconecte el
terminal de toma a tierra de la batería del
automóvil para evitar cortocircuitos.
• Asegúrese de utilizar altavoces con una
potencia nominal adecuada. Si emplea
altavoces de capacidad reducida, pueden
dañarse.
• Este amplificador es de fase invertida.
• No conecte el terminal # del sistema de
altavoces al chasis del automóvil, ni el terminal
# del altavoz derecho al del altavoz izquierdo.
• Instale los cables de entrada y salida alejados
del cable de la fuente de alimentación, ya que
en caso contrario puede generarse ruido por
interferencias.
• Esta unidad es un amplificador de alta
potencia. Por tanto, puede no funcionar a pleno
rendimiento si se utiliza con los cables de
altavoz suministrados con el automóvil.
• Si el automóvil está equipado con un sistema de
ordenador para la navegación o para otra
finalidad, no desconecte el conductor de toma a
tierra de la batería del automóvil. Si lo
desconecta, la memoria del ordenador puede
borrarse. Para evitar cortocircuitos al realizar
las conexiones, desconecte el cable de la fuente
de alimentación de +12 V hasta conectar todos
los cables.
Make the terminal connections as illustrated below.
Effectuez les connexions des bornes comme illustré ci-dessous.
Realice las conexiones de terminal como se ilustra a continuación.
Pass the wires through the cap, connect the wires, then cover the terminals with the cap.
Note
When you tighten the screw, be careful not to apply too much torque
*
as doing so may damage the screw.
*
The torque value should be less than 1 N•m.
Faites passer les fils par le cache, raccordez les fils, puis recouvrez les bornes avec le cache.
Remarque
Lorsque vous vissez la vis, faites attention à ne pas appliquer une trop grande force
*
, car cela pourrait
endommager la vis.
*
Le couple de serrage doit être inférieur à 1 N•m.
Pase los cables a través de la cubierta, conéctelos y cubra los terminales con dicha
cubierta.
Nota
Al apretar el tornillo, tenga cuidado de no aplicar demasiada fuerza de torsión
*
, ya que puede dañarlo.
*
El valor de fuerza de torsión debe ser inferior a 1 N•m.
R
E
M
+
12
V
GN
D
R
EM
+
1
2
V
GN
D
3
3
c
Power Connection Wires (not supplied)
Câbles d’alimentation (non fournis)
Cables de conexión de alimentación (no suministrados)
to a metal point of the car
vers un point métallique de la
carrosserie
a un punto metálico del
automóvil
Fuse (50 A)
Fusible (50 A)
Fusible (50 A)
+12 V car battery
Batterie de voiture +12 V
Batería de automóvil de +12 V
Car audio unit
Autoradio
Sistema de audio para
automóvil
Remote output
*
1
Sortie de télécommande
*
1
Salida remota
*
1
(REM)
less than 450 mm (18 in)
moins de 450mm (18 po)
menos de 450 mm
*
2
*
1
If you have the factory original or some other car audio unit without a remote output for the
amplifier, connect the remote input terminal (REMOTE) to the accessory power supply.
In High level input connection, car audio unit can also be activated without need for REMOTE
connection. However, this function is not guaranteed for all car audio units.
*
1
Si vous disposez de l’autoradio d’origine ou d’un autre autoradio dont l’amplificateur ne comporte pas
de sortie de télécommande à distance, raccordez la borne d’entrée de commande à distance (REMOTE)
à la prise d’alimentation accessoires.
Dans une connexion d’entrée à haut niveau, l’autoradio peut également être activé sans raccordement
à REMOTE. Toutefois, cette fonction n’est pas garantie pour tous les autoradios.
*
1
Si dispone del sistema de audio para automóvil original de fábrica o de otro sistema sin una salida
remota para el amplificador, conecte el terminal de entrada remota (REMOTE) a la fuente de
alimentación auxiliar.
En la conexión de entrada de alto nivel, el sistema de audio para automóvil también puede activarse
sin necesidad de conexión REMOTE. No obstante, esta función no se garantiza en todos los sistemas
de audio para automóvil.
Connections
5
XM-554ZR
Remarques sur l’alimentation électrique
• Raccordez le câble d’alimentation +12 V
uniquement après avoir réalisé toutes les autres
connexions.
• Raccordez solidement le fil de masse de l’appareil à
un point métallique de la carrosserie. Une
connexion lâche risque de provoquer un problème
de fonctionnement de l’amplificateur.
• Veillez à raccorder le fil de commande à distance de
l’autoradio à la borne de commande à distance.
•Si vous utilisez un autoradio dont l’amplificateur ne
comporte pas de sortie de commande à distance,
raccordez la borne d’entrée de commande à
distance (REMOTE) à la prise d’alimentation
accessoires.
•Utilisez un câble d’alimentation doté d’un fusible
(50A).
Notes on the power supply
• Connect the +12 V power supply wire only after all
the other wires have been connected.
• Be sure to connect the ground wire of the unit
securely to a metal point of the car. A loose
connection may cause a malfunction of the
amplifier.
• Be sure to connect the remote control wire of the
car audio unit to the remote terminal.
• When using a car audio unit without a remote
output on the amplifier, connect the remote input
terminal (REMOTE) to the accessory power supply.
• Use a power supply wire with a fuse attached (50
A).
Notas sobre la fuente de alimentación
• Conecte el cable de la fuente de alimentación de
+12 V sólo después de haber conectado los otros
cables.
• Asegúrese de conectar firmemente el cable de
toma a tierra de la unidad a un punto metálico del
automóvil. Una conexión floja puede causar fallos
de funcionamiento del amplificador.
• Compruebe que conecta el cable de control remoto
del sistema de audio para automóvil al terminal
remoto.
•Si utiliza un sistema de audio para automóvil sin
salida remota en el amplificador, conecte el
terminal de entrada remota (REMOTE) a la fuente
de alimentación auxiliar.
• Emplee el cable de la fuente de alimentación con
un fusible fijado (50 A).
•All power wires connected to the positive battery
post should be fused within 450 mm (18 in) of the
battery post, and before they pass through any
metal.
• Make sure that the vehicle’s battery wires
connected to the vehicle (ground to chassis)
*
2
are
of a wire gauge at least equal to that of the main
power wire connected from the battery to the
amplifier.
• During full-power operation, a current of more
than 50 A will run through the system. Therefore,
make sure that the wires to be connected to the
+12 V and GND terminals of this unit are at least
10-Gauge (AWG-10) or have a sectional area of
more than 5 mm
2
(
7
/
32
in
2
).
• Todos los cables de alimentación conectados al polo
positivo de la batería deben conectarse a un fusible
situado a menos de 450 mm del polo de la batería,
y antes de pasar por ninguna pieza metálica.
• Asegúrese de que los cables de la batería del
vehículo conectados al mismo (a la masa del
chasis)
*
2
tienen una anchura igual o superior a la
del cable de alimentación principal que conecta la
batería con el amplificador.
• Durante el funcionamiento a pleno rendimiento,
fluye por el sistema una corriente superior a 50 A.
Por tanto, compruebe que los cables que va a
conectar a los terminales de +12 V y GND de esta
unidad son del calibre 10 (AWG 10) como mínimo o
presentan un área de sección superior a 5 mm
2
.
• Tous les fils électriques raccordés à la borne positive
de la batterie doivent être protégés par un fusible à
une distance maximum de 450mm (18 po) à la
borne de la batterie et avant de passer dans une
partie métallique quelconque.
• Assurez-vous que les fils de la batterie du véhicule
raccordés à ce dernier (sol au châssis)
*
2
sont d’un
calibre au moins égal à celui du fil électrique
principal reliant la batterie et l’amplificateur.
• Pendant une utilisation à pleine puissance, un
courant d’une intensité supérieure à 50 A circule
dans le système. Assurez-vous que les câbles à
raccorder aux bornes +12 V et GND de cet appareil
sont de calibre supérieur à 10 (AWG-10) ou d’une
section supérieure à 5 mm
2
(
7
/
32
po
2
).
High Level Input Connection (with Speaker Connection 3)
Connexion d’entrée à haut niveau
(avec connexion de haut-parleur 3)
Conexión de entrada de alto nivel(con conexión de altavoces 3)
Line Input Connection
Connexion d’entrée de ligne
Conexión de entrada de línea
BB
BB
B
AA
AA
A
Input Connections/Connexions d’entrée/Conexiones de entrada
Rear
Arrière
Traseros
Front
Avant
Delanteros
Front right speaker output
Sortie du haut-parleur avant droit
Salida del altavoz delantero derecho
Rear right speaker output
Sortie du haut-parleur arrière droit
Salida del altavoz trasero derecho
Car audio unit
Autoradio
Sistema de audio para
automóvil
White
Blanc
Blanco
Grey
Gris
Gris
2
Car audio unit
Autoradio
Sistema de audio para
automóvil
Green
vert
Verde
Purple
Mauve
Violeta
Front left speaker output
Sortie du haut-parleur avant gauche
Salida del altavoz delantero izquierdo
Rear left speaker output
Sortie du haut-parleur arrière gauche
Salida del altavoz trasero izquierdo
LINE OUTLINE OUT
Striped
Rayé
Con rayas
Striped
Rayé
Con rayas
Striped
Rayé
Con rayas
Striped
Rayé
Con rayas
LR LR
FRONT REAR
High Level Input Connector
Connecteur d’entrée à haut niveau
Conector de entrada de alto nivel
Grey
Gris
Gris
White
Blanc
Blanco
Striped/White
Rayé blanc
Con rayas/Blanco
Striped/Grey
Rayé gris
Con rayas/Gris
Green
Vert
Verde
Purple
Mauve
Violeta
Striped/Purple
Rayé mauve
Con rayas/Violeta
Striped/Green
Rayé vert
Con rayas/Verde
6
XM-554ZR
4-Speaker System
Système à 4 haut-parleurs
Sistema de 4 altavoces
11
11
1
3-Speaker System
Système à 3 haut-parleurs
Sistema de 3 altavoces
22
22
2
2-Way System
Système 2 voies
Sistema de 2
vías
33
33
3
Speaker Connections
Turn on or off the LPF and HPF switch at the unit rear as illustrated below.
Conexións des haut-parleurs
Réglez le commutateur LPF et HPF situé à l’arrière de l’appareil à On ou Off, comme indiqué dans l’illustration ci-dessous.
Conexiones de los altavoces
Encienda o apague el interruptor LPF y HPF situados en la parte posterior de la unidad, como se muestra a continuación.
(80Hz)
OFF ON
LPF
(80Hz)
OFF ON
HPF
(80Hz)
OFF ON
LPF
(80Hz)
OFF ON
HPF
RL
Notes
•In this system, the volume of the subwoofer will be
controlled by the car audio unit fader control.
•In this system, the output signals to the subwoofer
will be the combination of both the REAR L and R
INPUT jacks or the REAR high level input connector
signals.
Remarques
• Dans ce système, le volume du caisson de graves
est contrôlé par la commande de balance avant/
arrière de l’autoradio.
• Dans ce système, les signaux émis vers le
caisson de graves sont constitués des signaux
des prises REAR L et R INPUT ou des signaux
du connecteur d’entrée de haut niveau REAR.
Front speaker (min. 2 Ω)
Haut-parleurs avant (min. 2 Ω)
Altavoces delanteros (mín. 2 Ω)
Notas
• En este sistema, el volumen del altavoz
potenciador de graves se controla mediante el
control de equilibrio entre altavoces del sistema de
audio para automóvil.
• En este sistema, las señales de salida que recibe el
altavoz potenciador de graves serán la
combinación de las tomas REAR L y R INPUT o de
las señales del conector de entrada de alto nivel
REAR.
Rear speaker (min. 2 Ω)
Haut-parleurs arrière (min. 2 Ω)
Altavoces traseros (mín. 2 Ω)
Left
gauche
Izquierdo
Right
droit
Derecho
Subwoofer (min. 4 Ω)
Caisson de graves (min. 4 Ω)
Altavoz potenciador de graves (mín. 4 Ω)
Full range speakers (min. 2 Ω)
Hauts-parleurs pleine gamme (min. 2 Ω)
Altavoces de gama completa (mín. 2 Ω)
(80Hz)
OFF ON
LPF
(80Hz)
OFF ON
HPF
Subwoofer (min. 2 Ω)
Caisson de graves (min. 2 Ω)
Altavoz potenciador de graves (mín. 2 Ω)
Full range speakers (min. 2 Ω)
Hauts-parleurs pleine gamme (min. 2 Ω)
Altavoces de gama completa (mín. 2 Ω)
Note
In this system, the volume of the subwoofer will be controlled by the car audio unit fader control.
Remarque
Dans ce système, le volume du caisson de graves est contrôlé par la commande de balance avant/arrière de
l’autoradio.
Nota
En este sistema, el volumen del altavoz potenciador de graves se controla mediante el control de equilibrio
entre altavoces del sistema de audio para automóvil.
Left
gauche
Izquierdo
Right
droit
Derecho
Left
gauche
Izquierdo
Right
droit
Derecho
Left
gauche
Izquierdo
Right
droit
Derecho
Left
gauche
Izquierdo
Right
droit
Derecho
7
XM-554ZR
SECTION 2
DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
Note : Follow the disassembly procedure in the numerical order given.
2-1. BOTTOM PLATE
1
three
screws
(+BTP 3
×
6)
3
bottom plat
e
2
four
screws
(+BTP 3
×
6)
2-1. BOTTOM PLATE
(Page 7)
2-2. AMP BOARD SECTION
(Page 8)
SET
2-3. PANEL (FRONT)
(Page 8)
8
XM-554ZR
2-2. AMP BOARD SECTION
2-3. PANEL (FRONT)
1
three
screw
s
(+P 3
×
8)
2
three
screws
(+P 3
×
8)
3
three
screws
(+P 3
×
8)
4
screw
(+BTP 3
×
8)
5
AMP board section
heat sink (main)
1
three
screws
(+P 3
×
8)
2
screw
(+P 3
×
8)
3
screw
(+P 3
×
8)
4
panel (front)
5
AMP board
99
XM-554ZR
XM-554ZR
SECTION 3
DIAGRAMS
3-1. BLOCK DIAGRAM
3
2
1
PRE AMP
IC801 (1/2)
1
GAIN CONTROL AMP
IC805 (1/2)
HPF
IC803 (1/2)
DIFFERENTIAL
AMP
Q103
POWER
AMP
Q110
DRIVE
AMP
Q104
DIFFERENTIAL
AMP
Q102
POWER
AMP
Q111
DRIVE
AMP
Q105
BIAS
Q106,107
BIAS
Q206,207
CN902 (1/2)
CN901
MUTE
SWITCH
Q101
+12V
GND
9
PRE AMP
IC801 (2/2)
DIFFERENTIAL
AMP
Q203
POWER
AMP
Q210
DRIVE
AMP
Q204
DIFFERENTIAL
AMP
Q202
MUTE
CONTROL
Q802
POWER
AMP
Q211
DRIVE
AMP
Q205
-3
-2
-4
FL
FR
RL
RR
-1
L
FRONT
INPUT
D906
D907
REAR
R
CN903
L
R
MUTE
SWITCH
Q201
1
2
14
12
REF.
REG
CN905
F901
25A
SWITCHING
DRIVER
Q910,911
SWITCHING
DRIVER
Q912,913
DRIVER
Q908,909
8
10
11
3
LED901
POWER/
PROTECTOR
FRONT
SPEAKER
OUT
DC-DC
CONVERTER
TRANSFORMER
T901
DC-DC CONVERTER
IC903
B+
SWITCH
Q905
OVERLOAD
DET
Q112
OVERLOAD
DET
Q212
CN904
L
(L+R)
R
REAR
SPEAKER
OUT
6
5
CN902 (2/2)
L
(L+R)
R
(L+R)
REM
+15V REG
Q807
–15V REG
Q808
PROTECTOR
DETECT
Q901,902
OVERLOAD
PROTECT
(REAR)
Q805,806
OVERLOAD
PROTECT
(FRONT)
Q803,804
POWER
ON/OFF
Q906
DC DET
IC902
+30V
+15V
–30V
–15V
D804
RECT
D803
RECT
(FRONT)
(REAR)
HIGH
LEVEL
INPUT/
SENSING
POWER ON
F902
25A
PRE AMP
IC802 (1/2)
1
LPF
IC804 (1/2)
GAIN CONTROL AMP
IC806 (1/2)
DIFFERENTIAL
AMP
Q303
POWER
AMP
Q310
DRIVE
AMP
Q304
DIFFERENTIAL
AMP
Q302
POWER
AMP
Q311
DRIVE
AMP
Q305
MUTE
SWITCH
Q301
PRE AMP
IC802 (2/2)
3
7
LPF
IC804 (2/2)
DIFFERENTIAL
AMP
Q403
POWER
AMP
Q410
DRIVE
AMP
Q404
DIFFERENTIAL
AMP
Q402
POWER
AMP
Q411
DRIVE
AMP
Q108
DRIVE
AMP
Q109
DRIVE
AMP
Q208
DRIVE
AMP
Q209
DRIVE
AMP
Q308
DRIVE
AMP
Q309
DRIVE
AMP
Q408
DRIVE
AMP
Q409
DRIVE
AMP
Q405
MUTE
SWITCH
Q401
OVERLOAD
DET
Q412
6
OVERLOAD
DET
Q312
3
2
5
BUFFER
Q904
TEMP.DET
TH901-903
LED DRIVER
Q903
R
(PROTECTOR)
G
(POWER)
THERMAL DET
Q914,915
VCC
REF
D905
D901
D902
OVER
VOLTAGE
DETECT
Q907
2
HPF
3
2
7
7
GAIN CONTROL AMP
IC805 (2/2)
HPF
IC803 (2/2)
6
HPF
LPF
5
6
LPF
2
3
6 7
GAIN CONTROL AMP
IC806 (2/2)
2 1
6
5
MUTE
CONTROL
Q810
MUTE
CONTROL
Q809
MUTE
CONTROL
Q811
MUTE
CONTROL
Q812
15
16
1
7
1
7
BIAS
Q306,307
BIAS
Q406,407
VR801-1
VR801-2
VR802-1
VR802-2
SW801-1
SW801-2
VR801
LEVEL
(FRONT)
ON
OFF
VR802
LEVEL
(REAR)
SW801
HPF
(80Hz)
(FRONT)
OFF ON
SW802
SW802-1
SW802-2
LPF
(80Hz)
(REAR)
• Signal path
: AUDIO
10 10
XM-554ZR
XM-554ZR
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
for schematic diagram:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and
1
/
4
W or less unless otherwise
specified.
• A : B+ Line.
• B : B– Line.
• Power voltage is dc 14.4V and fed with regulated dc power
supply from +12V and REM terminals.
•Voltage is dc with respect to ground under no-signal
condition.
•Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
•Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : AUDIO
for printed wiring boards:
• : Pattern from the side which enables seeing.
• Waveform
1 V/DIV, 10
µ
sec/DIV
1 IC903 5
3.3 Vp-p
18
µ
sec
Ver. 1.1
Note:
The components identi-
fied by mark 0 or dotted
line with mark 0 are criti-
cal for safety.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce portant le numéro
spécifié.
11 11
XM-554ZR
XM-554ZR
3-2. PRINTED WIRING BOARD : Uses unleaded solder.
Ref. No. Location
D101 F-4
D102 F-4
D201 F-5
D202 F-4
D301 F-6
D302 F-5
D401 F-7
D402 F-6
D801 G-9
D802 G-9
D803 B-13
D804 C-13
D805 F-7
D806 F-8
D807 D-10
D901 B-4
D902 G-10
D904 H-10
D905 G-10
D906 I-6
D907 I-6
IC801 H-5
IC802 H-6
IC803 G-4
IC804 G-7
IC805 G-4
IC806 H-7
IC902 F-9
IC903 E-10
LED901 I-8
Q101 G-4
Q102 F-4
Q103 F-4
Q104 E-4
Q105 E-4
Q106 F-2
Q107 F-2
Q108 E-4
Q109 E-4
Q110 E-1
Q111 F-1
Q112 D-2
Q201 G-4
Q202 F-5
Q203 F-5
Q204 E-5
Q205 E-5
Q206 C-2
Q207 C-2
Q208 E-5
Q209 E-5
• Semiconductor Location
Q210 C-1
Q211 D-1
Q212 B-2
Q301 G-6
Q302 F-6
Q303 F-6
Q304 E-6
Q305 E-5
Q306 B-6
Q307 C-6
Q308 E-6
Q309 E-5
Q310 A-7
Q311 A-5
Q312 B-7
Q401 F-6
Q402 F-7
Q403 F-7
Q404 E-7
Q405 E-6
Q406 B-8
Q407 C-8
Q408 E-7
Q409 E-6
Q410 A-9
Q411 A-8
Q412 C-10
Q802 G-9
Q803 H-3
Q804 H-3
Q805 G-8
Q806 G-8
Q807 F-8
Q808 E-8
Q809 G-7
Q810 G-7
Q811 G-6
Q812 G-6
Q901 E-10
Q902 E-10
Q903 I-8
Q904 F-10
Q905 G-10
Q906 G-10
Q907 H-10
Q908 E-11
Q909 E-11
Q910 E-13
Q911 F-13
Q912 E-13
Q913 D-13
Q914 G-10
Q915 G-10
Ref. No. Location
1
A
B
C
D
E
F
G
H
I
J
2345678910111213
C308
-1 -7
-2 -8
FL RLFR RR
L R
POWER/
PROTECTOR
LED901
JW187
JW100
JW95
JW98
JW97
JW105
JW126
RG
(PROTECTOR)
(POWER)
C212
JW3
JW1
JW4
JW6
JW5
JW7
JW11
JW198
JW46
JW107
VR802
JW32
JW28
JW12
JW13
JW33
JW20
JW10
JW21
JW157
JW16
JW15
JW9
JW135
JW19
JW36
JW24
JW23
JW8
JW14
JW2
JW25
R164
SW802
SW801
VR801
C155
R172
R272
C355
C455
C912
C255
C802
Q903
R934
R919
R472
R372
R933
R932
Q112
R367
R165
Q107
Q106
Q206
D102
C2
B2 B1
B1
E
C1 C2
B2 B1E
C1
C2
B2 B1E
C1
C2
B2 B1E
C1
C2
B2E
C1
B1
C2
B2E
C1 C2
B2 B1E
C1
B1
C2
B2E
C1
Q202
Q203
Q302 Q303
C210
C110
IC804
IC903
C905
IC806
IC802
Q907
Q906
Q915
D905
Q914
Q805
Q806
D904
C909
C916
C917R903
R901
C902
R902
C901
R906
JW173
JW170
R947
R911
R920
R921
R923
R922
R924
R925
JR3
TH903
R926
R930
Q908
Q909
R927
R910
C904
C907
R912
C915
JW151
JW150
L803
C819
C821
C822
C820
L802
L805
L804
JW155
JW154
R931
R929
R928
C911
R942
R904
JW196
JW34
JW106
JW108
JW107
JW160
JW161
JW138
JW163
JW130
JW132
JW131
JW162
JW167
JW109
C810
JW195
R471
R813
C812
R371
JW22
R936
R940
R914
R915
C919
R935R938
R939
JR4
C903
D902
Q904
C311
C411
D906 D907
R811
C409
C408
C310
R311
R310
R309
R414
R807
R937
C921
R916
R941
R809
R808
R909
R308
C416
C401
R943
R944
R945
R946
C402
R301
C202
R801
C801
R803
C803
R404
C405
R403
R201
C102
R212
R211
R112
R210
R102
JW50
JW51
C811 R271
R812
R113
R810
JW29
R111
JR1
R213
R804
R101
R402
R302
R207
R203
R205
R204
C216
C217
C804
C805 R805
C302
C201
C301
R202
R802
R110
R401
C417
C316
C317
C101
C407
R406
R206
R306
R304
R303
R307
R305
R103
R104
C116
C117
R105
R107
C107
C108
R108
C109
R109
C809
R162
R155
R156 R158
R157
R153
C153
R161
R154
R262
R253
C253
R261
R254
R362
R355
R356
R357
R358
C354
C454
R353
C353
R361
R354
R452
R462
R453
C453
R461
R454
R457
R458
R456
R455
R255
R256
R258
R257
R114
C112
R209
C808
C208
C111
C306
C815
C406
R407
R405
R410
R313
R411
R409
C410
R413
R412
C312 C412
R312
R314
R408
C307
R208C209
R214
R171
C206
C205 C207
C105
R251
C106
R106
R252
R151
C305
C309
R905
C918
R917
R918
IC801
Q201
R152
C151
R173
Q102 Q103
R176 R175
R174
R273
R276
C152R160
R159
R260
R166
R266
C252
R259
R360
R275
R274
R376
Q402
Q403
R373
JR2
R352
R351
JR6
R451
JR5
Q301
Q812 Q811
Q810
Q809
C451
C351
C826
R806 R818
R816 R817
R374
R473
C825
C827
C824
D805
D806
R474
R476
C452
R459
D401
D301
R815
R814
R359
C352
R366
R460
R466
R475
R375
Q101
IC805 IC803
Q105
Q104
Q205
Q204
D201
Q108
Q109
Q209
Q208
Q305
Q807
Q405Q304
Q404
IC902
4
3
1
2
JW191
JW192
JW128
JW133
C908
C920
C814
JW190
JW189
JW188
JW127
C914
C913
JW143
JW186
JW185
JW184
JW183
JW180
C910
JW179
JW178
L901
JW182
JW181
JW112
JW84
JW166
JW165
JW164
JW121
JW76
R469
R369
Q310Q311
EC B EC B ECB E
ECB
ECB
CB
Q411 Q410
JW124
JW174
JW120
JW145
JW146
JW99
JW144
JW123
JW122
JW172
JW171
JW125
C906
C211
C251
C154
C254
R168
R177
R167
R170
JW65
R269
R169
JW67
JW66
JW53
JW54
JW55
JW27
JW26
JW48
JW49
C813
JW58
JW41
JW31
JW30
JW35
JW18
JW47
JW17
JW59
JW68
JW62
JW63
JW61
JW60
JW52
JW56
JW57
JW71
JW70
JW83
JW74 JW78 JW82
JW75
JW72
JW73
JW79
JW93
JW39 JW94
JW45
JW37
JW38
JW43
JW42
JW96
JW81
JW85
JW77
JW80
R268
TH901
R267
R270
R278
R277
E C B
B C E
E C B
E C B
E C B
B C E
B C E
D402
D302
B C E
E C B E C B
Q901
E C B
Q902
D807
T901
E C B
B C E
B C E
E C B E C B
E C B
Q804
E C B
Q803
E C B
B C E
B C E
B C E
Q401
B C E
B C E
Q308
Q408
B C EQ309
B C E
B C E
B C E
B C E
B C E
Q409
B C E
B C E
B C E
Q802
D801
D802
B C E
D101
D202
E C B
E C B
B C E
B C E
R907
R908
TH902
R364
R365
Q307
Q312
Q407
E C B
Q412
Q406
Q808
Q306
R465
R463
C817
R378
R363
R470
R478
R464
R468
R370R377
R368
R467
R477
C818
L801
JW139
C823
R265
C118
R178
R163
C119
Q207
Q212
1-868-781-
Q111 Q110 Q211 Q210
E
C
B
E
C
B
B
C
E
B
C
E
B
C
E
B
C
E
D901
R263
R264
916
81
41
58
41
58
41
58
41
58
41
58
41
58
JW158
JW152
JW153
D803D804Q913
A
K
A
K
A
K
S
D
G
Q912
S
D
G
Q910
S
D
G
Q911
S
D
G
JW168
JW177
JW176
JW92
Q905
BCE
JW169
JW134
JW149
JW147
JW148
JW129
JW175
11
AMP BOARD
-2
-1
-4
-3
-6
-5
-8
-7
OFF ON
SW802
LPF(80Hz)
OFF ON
SW801
HPF(80Hz)
CN902
(L+R)
INPUT
CN901
HIGH LEVEL INPUT/
SENSING POWER ON
JW111
VR801
LEVEL
VR802
LEVEL
25A
F902
25A
F901
REM +12V GND
REAR SPEAKER OUT
CN904
(L+R)
CN905
JW104
JW103
JW102
JW101
JW114JW110
JW115JW88
JW113
JW116
JW117
JW118
JW119
JW89
JW90
JW91
JW159
JW86
JW87
JW142
JW141
JW140
JW69
JW64
L
R
FRONT SPEAKER OUT
FRONT
CN903
REAR
-2
-1
L
-3
L
-2
R
-4
R
-1
-1
-2
-2
-1
-1
-2
12 12
XM-554ZR
XM-554ZR
3-3. SCHEMATIC DIAGRAM — AMP SECTION (1/2) —
(Page 13)
R202
R402
R802
C801R801
R803 C803
R804 C804
R102
R103
R101
C201
C202
R201
R301
R401
C108 C109
C111
C110
R111 R110
R203
C205
C206
C207
C208
C210
C211
R210R211
C112 R151
R251
R302
R303
R403
C301
C302
C401
C402
C305
C306
C307
C808
C407
C405
C815
C809
R309
C308
R310
SW802
R409 R410
C408
C311
C312
C411
R351
R451
C412
R153
R161
R159
R162
C154
R160
R164
R165
R166
R167
R169
R168
R170
R259
R253 R261
R262
R260
C254
R264
R265
R267
R269
R268
R270
R353 R361
R362
R360
R359
C354
R364
R365
R366
R367
R369
R368
R370
R453
R459
R461
R462
R460
C454
R464
R466
R467
R468
R469
R470
R172
R272
R372
R472
C106
C105
C107
C209
SW801
C406
R266
C212
R465
VR801
VR801
VR802
VR802
CN902
CN902
R104 R105
R109
R209
R113
R114
R214
R806
R816
R817
R818
C116
C117
C216 C217
C417
C416
C317 C316
R205 R204
R305 R304
R943
R944
R945
R946
C802
R404 R405
C309
C310
C410
C409
R313
R413
R314
R414
R174
R173
R273
R274
R373
R374
R473
R474
Q103
Q203
Q303
Q403
Q102
Q202
Q302
Q402
Q108
Q208
Q308
Q408
Q109
Q209
Q309
Q409
Q110
Q210
Q310
Q410
Q111
Q211
Q311
Q411
R178
R278
R378
R478
C118
C119
R213
Q201
Q101
Q301
Q401
C101
C102
C151
C251
C351
C451
Q104
Q204
Q304
Q404
Q105
Q205
Q305
Q405
R154
R254
R354
R454
CN901
CN902
CN903
CN904
IC801(1/2)
IC803(1/2)
IC805(1/2)
IC805(2/2)
IC803(2/2)
IC801(2/2)
R106
R107
R207
R206
R208
R212
R252
R152
R112
D906
D907
IC802(1/2)
R308 R311
IC804(1/2)
R307
R306
R312
IC806(1/2)
R352
R452
IC806(2/2)
R412
IC804(2/2)
R411
R408
R407
IC802(2/2)
R406
C155
C255
C355
C455
R155
R158
R175
D101
C152
C153
R163
Q107
R157
R176
R156
D102
Q112
Q106
R177
R171
R255
R258 R275
D201
C252
C253
D202
R256
R276R257
R263
Q206
R355
R358 R375
D301
C352
C353
D302
R356
R376R357
R363
Q312
R455
R458 R475
D401
C452
C453
D402
R456
R476R457
R463
Q412
R277
R271
R371
R471
Q307
Q306
Q207
Q406
Q407
R477
R377
R108
Q212
13 13
XM-554ZR
XM-554ZR
• Refer to page 10 for Waveform.
3-4. SCHEMATIC DIAGRAM — AMP SECTION (2/2) — • Refer to page 14 for IC Block Diagram.
(Page 12)
IC B/D
F901
R912
F902
R919
C909
R918
R917
R916
R934 C911
R809
C904
R911
C906
C907
C903
C901
R903
R902
R901
C917
R805 C805
R928
R931
R920
R921
R922
R923
R924
R925
R929
R930
C913
C914
C817
C818
C819
C821
C820
C822
C823
R814
R815
C824
C825
C826
C827
R810
C811
C813
R811
C814
C915
C916
R932
R933
R914
C910
C918
R942
L901
R940
C920
R937
C921
R936
R935
C919
C908
R904
Q902
Q901
C902
R905
C812
R813
R812
D803
D804
Q807
Q808
Q913
Q911
Q910
Q912
Q908
Q909
R927
R926
R807
Q812 Q811 Q809 Q810
C810
L804
L805
L802
L803
T901
TH903
TH902
TH901
CN905
D802
Q802
D801
R808
C912
L801 D805
D806
Q905
IC902
R915
D904
Q906
Q907
D905
R941
R938
Q915
Q914
R939
D901
D902
R909
R908
R907
Q904
R947
IC903
R910 C905
R906
Q903
LED901
D807
Q803
Q804
Q805
Q806
15
XM-554ZR
SECTION 4
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
Parts Color Cabinet’s Color
• Accessories are given in the last of this parts list.
Ref. No. Part No. Description Remark
4-1. HEAT SINK (MAIN) SECTION
R
Ref. No. Part No. Description Remark
R
12-663-766-01 PLATE (TOP), ORNAMENTAL
22-663-767-01 PLATE (SIDE), ORNAMENTAL
0 F901 1-576-256-11 FUSE (BLADE TYPE) (AUTO FUSE) (25A)
0 F902 1-576-256-11 FUSE (BLADE TYPE) (AUTO FUSE) (25A)
#1 7-685-146-19 SCREW +P 3X8 TYPE2 NON-SLIT
#2 7-685-545-19 SCREW +BTP 3X6 TYPE2 N-S
F901
F902
not supplied
not supplied
#1
#1
#1
#1
#1
#2
#2
#2
1
2
Ver. 1.1
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
16
XM-554ZR
4-2. AMP BOARD SECTION
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
51 A-1176-995-A AMP BOARD, COMPLETE
52 3-225-183-02 SCREW (+PSW.TT.3XL)
53 2-663-768-01 PANEL (FRONT)
54 3-912-432-11 SCREW (+–B)
D803 6-501-466-01 DIODE F1B2CCI
D804 6-501-467-01 DIODE F1B2CAI
Q110 6-551-502-01 TRANSISTOR KTD998
Q111 6-551-503-01 TRANSISTOR KTB778
Q210 6-551-502-01 TRANSISTOR KTD998
Q211 6-551-503-01 TRANSISTOR KTB778
Q306 8-729-041-66 TRANSISTOR 2SC4015TV2
Q311 6-551-503-01 TRANSISTOR KTB778
Q406 8-729-041-66 TRANSISTOR 2SC4015TV2
Q410 6-551-502-01 TRANSISTOR KTD998
Q910 6-551-506-01 FET IRFI3205
Q911 6-551-506-01 FET IRFI3205
Q912 6-551-506-01 FET IRFI3205
Q913 6-551-506-01 FET IRFI3205
#1 7-685-146-19 SCREW +P 3X8 TYPE2 NON-SLIT
#1
#1
#1
51
52
52
52
52
52
53
54
54
54
52
52
not supplied
not supplied
Q911,Q910,Q912,Q913
Q111,Q110,
Q211,Q210
Q311,Q306,Q406,Q410
D804,D803
not supplied
17
XM-554ZR
SECTION 5
ELECTRICAL PARTS LIST
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORS
uF : µF
• COILS
uH : µH
A-1176-995-A AMP BOARD, COMPLETE
*********************
3-225-183-02 SCREW (+PSW.TT.3XL)
3-912-432-11 SCREW (+–B)
< CAPACITOR >
C101 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C102 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C105 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C106 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C107 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C108 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C109 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C110 1-126-933-11 ELECT 100uF 20% 16V
C111 1-126-963-11 ELECT 4.7uF 20% 50V
C112 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C116 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C117 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C118 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C119 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C151 1-126-947-11 ELECT 47uF 20% 35V
C152 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C153 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C154 1-126-960-11 ELECT 1uF 20% 50V
C155 1-137-397-11 MYLAR 0.047uF 5% 100V
C201 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C202 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C205 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C206 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C207 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C208 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C209 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C210 1-126-933-11 ELECT 100uF 20% 16V
C211 1-126-963-11 ELECT 4.7uF 20% 50V
C212 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C216 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C217 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C251 1-126-947-11 ELECT 47uF 20% 35V
C252 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C253 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C254 1-126-960-11 ELECT 1uF 20% 50V
C255 1-137-397-11 MYLAR 0.047uF 5% 100V
C301 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C302 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C305 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C306 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C307 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C308 1-126-960-11 ELECT 1uF 20% 50V
C309 1-164-336-11 CERAMIC CHIP 0.33uF 25V
C310 1-164-345-11 CERAMIC CHIP 0.082uF 10% 25V
C311 1-126-933-11 ELECT 100uF 20% 16V
C312 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C316 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C317 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C351 1-126-947-11 ELECT 47uF 20% 35V
C352 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C353 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C354 1-126-960-11 ELECT 1uF 20% 50V
C355 1-137-397-11 MYLAR 0.047uF 5% 100V
C401 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C402 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C405 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C406 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C407 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C408 1-126-960-11 ELECT 1uF 20% 50V
C409 1-164-336-11 CERAMIC CHIP 0.33uF 25V
C410 1-164-345-11 CERAMIC CHIP 0.082uF 10% 25V
C411 1-126-933-11 ELECT 100uF 20% 16V
C412 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C416 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C417 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C451 1-126-947-11 ELECT 47uF 20% 35V
C452 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C453 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C454 1-126-960-11 ELECT 1uF 20% 50V
C455 1-137-397-11 MYLAR 0.047uF 5% 100V
C801 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C802 1-126-934-11 ELECT 220uF 20% 16V
C803 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C804 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C805 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C808 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C809 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C810 1-126-965-11 ELECT 22uF 20% 50V
C811 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C812 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C813 1-104-655-11 ELECT 470uF 20% 6.3V
C814 1-104-655-11 ELECT 470uF 20% 6.3V
C815 1-126-933-11 ELECT 100uF 20% 16V
When indicating parts by reference
number, please include the board.
AMP
Ver. 1.1
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
18
XM-554ZR
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C817 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C818 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C819 1-165-949-11 ELECT 1500uF 20% 35V
C820 1-165-949-11 ELECT 1500uF 20% 35V
C821 1-165-949-11 ELECT 1500uF 20% 35V
C822 1-165-949-11 ELECT 1500uF 20% 35V
C823 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C824 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C825 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C826 1-126-933-11 ELECT 100uF 20% 16V
C827 1-126-933-11 ELECT 100uF 20% 16V
C901 1-100-352-11 CERAMIC CHIP 1uF 20% 16V
C902 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C903 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C904 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C905 1-137-410-11 MYLAR 0.001uF 10% 100V
C906 1-126-933-11 ELECT 100uF 20% 16V
C907 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C908 1-126-933-11 ELECT 100uF 20% 16V
C909 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V
C910 1-117-378-11 FILM 1uF 5% 50V
C911 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C912 1-137-397-11 MYLAR 0.047uF 5% 100V
C913 1-131-731-21 ELECT 2200uF 20% 16V
C914 1-131-731-21 ELECT 2200uF 20% 16V
C915 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C916 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C917 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C918 1-100-352-11 CERAMIC CHIP 1uF 20% 16V
C919 1-100-352-11 CERAMIC CHIP 1uF 20% 16V
C920 1-126-965-11 ELECT 22uF 20% 50V
C921 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
< CONNECTOR >
CN901 1-580-283-11 PIN, CONNECTOR (PC BOARD) 8P
(HIGH LEVEL INPUT/SENSING POWER ON)
< JACK >
CN902 1-779-078-32 JACK, PIN 4P (INPUT FRONT/REAR)
< TERMINAL BOARD >
CN903 1-780-406-11 TERMINAL BOARD (4P)
(FRONT SPEAKER OUT)
CN904 1-780-406-11 TERMINAL BOARD (4P) (REAR SPEAKER OUT)
CN905 1-780-351-11 TERMINAL BOARD (3P+FUSE)
(GND,+12V,REM,25A,25A)
< DIODE >
D101 8-719-801-78 DIODE 1SS184
D102 8-719-801-78 DIODE 1SS184
D201 8-719-801-78 DIODE 1SS184
D202 8-719-801-78 DIODE 1SS184
D301 8-719-801-78 DIODE 1SS184
D302 8-719-801-78 DIODE 1SS184
D401 8-719-801-78 DIODE 1SS184
D402 8-719-801-78 DIODE 1SS184
D801 8-719-025-34 DIODE 02CZ6.8-TE85L
D802 8-719-801-78 DIODE 1SS184
D803 6-501-466-01 DIODE F1B2CCI
D804 6-501-467-01 DIODE F1B2CAI
D805 8-719-025-50 DIODE 02CZ16-TE85L
D806 8-719-025-50 DIODE 02CZ16-TE85L
D807 8-719-801-78 DIODE 1SS184
D901 8-719-801-78 DIODE 1SS184
D902 8-719-801-78 DIODE 1SS184
D904 8-719-025-50 DIODE 02CZ16-TE85L
D905 8-719-801-78 DIODE 1SS184
D906 8-719-801-78 DIODE 1SS184
D907 8-719-801-78 DIODE 1SS184
< FUSE >
0 F901 1-576-256-11 FUSE (BLADE TYPE) (AUTO FUSE) (25A)
0 F902 1-576-256-11 FUSE (BLADE TYPE) (AUTO FUSE) (25A)
< IC >
IC801 8-759-745-64 IC NJM4560M
IC802 8-759-745-64 IC NJM4560M
IC803 8-759-745-64 IC NJM4560M
IC804 8-759-745-64 IC NJM4560M
IC805 8-759-745-64 IC NJM4560M
IC806 8-759-745-64 IC NJM4560M
IC902 6-600-354-01 IC PC-17K1
IC903 8-759-144-88 IC uPC494GS
< JUMPER RESISTOR >
JR1 1-216-296-11 SHORT CHIP 0
JR2 1-216-296-11 SHORT CHIP 0
JR3 1-216-296-11 SHORT CHIP 0
JR4 1-216-296-11 SHORT CHIP 0
JR5 1-216-296-11 SHORT CHIP 0
JR6 1-216-296-11 SHORT CHIP 0
< COIL >
L801 1-410-396-71 INDUCTOR, FERRITE BEAD 0.45uH
L901 1-411-756-11 COIL, CHOKE 50uH
< DIODE >
LED901 8-719-064-11 LED SPR-325MVW (POWER/PROTECTOR)
< TRANSISTOR >
Q101 6-550-686-01 TRANSISTOR KTC2875-B-RTK
Q102 6-551-504-01 TRANSISTOR KTA501U
Q103 6-551-505-01 TRANSISTOR KTC601U
Q104 6-551-508-01 TRANSISTOR KTA1268
Q105 8-729-045-02 TRANSISTOR KTC3200GR-AT
Q106 8-729-041-66 TRANSISTOR 2SC4015TV2
Q107 8-729-034-50 TRANSISTOR KTA1504
Q108 6-550-693-01 TRANSISTOR KTC4373
Q109 6-550-690-01 TRANSISTOR KTA1661
Q110 6-551-502-01 TRANSISTOR KTD998
Q111 6-551-503-01 TRANSISTOR KTB778
Q112 8-729-034-51 TRANSISTOR KTC3875
Q201 6-550-686-01 TRANSISTOR KTC2875-B-RTK
Q202 6-551-504-01 TRANSISTOR KTA501U
Q203 6-551-505-01 TRANSISTOR KTC601U
AMP
19
XM-554ZR
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
Q204 6-551-508-01 TRANSISTOR KTA1268
Q205 8-729-045-02 TRANSISTOR KTC3200GR-AT
Q206 8-729-041-66 TRANSISTOR 2SC4015TV2
Q207 8-729-034-50 TRANSISTOR KTA1504
Q208 6-550-693-01 TRANSISTOR KTC4373
Q209 6-550-690-01 TRANSISTOR KTA1661
Q210 6-551-502-01 TRANSISTOR KTD998
Q211 6-551-503-01 TRANSISTOR KTB778
Q212 8-729-034-51 TRANSISTOR KTC3875
Q301 6-550-686-01 TRANSISTOR KTC2875-B-RTK
Q302 6-551-504-01 TRANSISTOR KTA501U
Q303 6-551-505-01 TRANSISTOR KTC601U
Q304 6-551-508-01 TRANSISTOR KTA1268
Q305 8-729-045-02 TRANSISTOR KTC3200GR-AT
Q306 8-729-041-66 TRANSISTOR 2SC4015TV2
Q307 8-729-034-50 TRANSISTOR KTA1504
Q308 6-550-693-01 TRANSISTOR KTC4373
Q309 6-550-690-01 TRANSISTOR KTA1661
Q310 6-551-502-01 TRANSISTOR KTD998
Q311 6-551-503-01 TRANSISTOR KTB778
Q312 8-729-034-51 TRANSISTOR KTC3875
Q401 6-550-686-01 TRANSISTOR KTC2875-B-RTK
Q402 6-551-504-01 TRANSISTOR KTA501U
Q403 6-551-505-01 TRANSISTOR KTC601U
Q404 6-551-508-01 TRANSISTOR KTA1268
Q405 8-729-045-02 TRANSISTOR KTC3200GR-AT
Q406 8-729-041-66 TRANSISTOR 2SC4015TV2
Q407 8-729-034-50 TRANSISTOR KTA1504
Q408 6-550-693-01 TRANSISTOR KTC4373
Q409 6-550-690-01 TRANSISTOR KTA1661
Q410 6-551-502-01 TRANSISTOR KTD998
Q411 6-551-503-01 TRANSISTOR KTB778
Q412 8-729-034-51 TRANSISTOR KTC3875
Q802 8-729-034-51 TRANSISTOR KTC3875
Q803 8-729-034-51 TRANSISTOR KTC3875
Q804 8-729-034-51 TRANSISTOR KTC3875
Q805 8-729-034-51 TRANSISTOR KTC3875
Q806 8-729-034-51 TRANSISTOR KTC3875
Q807 6-551-511-01 TRANSISTOR KTD2424
Q808 6-551-510-01 TRANSISTOR KTB1424
Q809 8-729-038-54 TRANSISTOR KRA102S
Q810 8-729-038-54 TRANSISTOR KRA102S
Q811 8-729-038-54 TRANSISTOR KRA102S
Q812 8-729-038-54 TRANSISTOR KRA102S
Q901 8-729-038-67 TRANSISTOR KRC102S
Q902 8-729-038-54 TRANSISTOR KRA102S
Q903 8-729-038-67 TRANSISTOR KRC102S
Q904 8-729-034-51 TRANSISTOR KTC3875
Q905 8-729-040-76 TRANSISTOR KTA1273-Y-AT
Q906 8-729-034-51 TRANSISTOR KTC3875
Q907 8-729-038-67 TRANSISTOR KRC102S
Q908 6-551-507-01 TRANSISTOR MMBTA06
Q909 6-551-507-01 TRANSISTOR MMBTA06
Q910 6-551-506-01 FET IRFI3205
Q911 6-551-506-01 FET IRFI3205
Q912 6-551-506-01 FET IRFI3205
Q913 6-551-506-01 FET IRFI3205
Q914 8-729-034-51 TRANSISTOR KTC3875
Q915 8-729-034-50 TRANSISTOR KTA1504
< RESISTOR >
R101 1-216-206-00 RES-CHIP 2.2K 5% 1/8W
R102 1-216-837-11 METAL CHIP 22K 5% 1/10W
R103 1-216-837-11 METAL CHIP 22K 5% 1/10W
R104 1-216-849-11 METAL CHIP 220K 5% 1/10W
R105 1-216-849-11 METAL CHIP 220K 5% 1/10W
R106 1-218-875-11 METAL CHIP 15K 0.5% 1/10W
R107 1-218-875-11 METAL CHIP 15K 0.5% 1/10W
R108 1-218-875-11 METAL CHIP 15K 0.5% 1/10W
R109 1-216-840-11 METAL CHIP 39K 5% 1/10W
R110 1-216-833-11 METAL CHIP 10K 5% 1/10W
R111 1-216-833-11 METAL CHIP 10K 5% 1/10W
R112 1-218-843-11 METAL CHIP 680 0.5% 1/10W
R113 1-216-833-11 METAL CHIP 10K 5% 1/10W
R114 1-216-837-11 METAL CHIP 22K 5% 1/10W
R151 1-216-222-00 RES-CHIP 10K 5% 1/8W
R152 1-216-841-11 METAL CHIP 47K 5% 1/10W
R153 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R154 1-216-218-11 RES-CHIP 6.8K 5% 1/8W
R155 1-218-883-11 METAL CHIP 33K 0.5% 1/10W
R156 1-218-883-11 METAL CHIP 33K 0.5% 1/10W
R157 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R158 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R159 1-216-809-11 METAL CHIP 100 5% 1/10W
R160 1-216-809-11 METAL CHIP 100 5% 1/10W
R161 1-216-845-11 METAL CHIP 100K 5% 1/10W
R162 1-216-845-11 METAL CHIP 100K 5% 1/10W
R163 1-218-843-11 METAL CHIP 680 0.5% 1/10W
R164 1-216-813-11 METAL CHIP 220 5% 1/10W
R165 1-216-833-11 METAL CHIP 10K 5% 1/10W
R166 1-216-182-00 RES-CHIP 220 5% 1/8W
R167 1-216-134-00 RES-CHIP 2.2 5% 1/8W
R168 1-216-134-00 RES-CHIP 2.2 5% 1/8W
R169 1-205-991-11 ENCAPSULATED COMPONENT 0.1X2 5W
R170 1-216-833-11 METAL CHIP 10K 5% 1/10W
R171 1-218-893-11 METAL CHIP 82K 0.5% 1/10W
R172 1-249-385-11 CARBON 2.2 5% 1/4W F
R173 1-216-837-11 METAL CHIP 22K 5% 1/10W
R174 1-216-837-11 METAL CHIP 22K 5% 1/10W
R175 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R176 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R177 1-218-875-11 METAL CHIP 15K 0.5% 1/10W
R178 1-216-833-11 METAL CHIP 10K 5% 1/10W
R201 1-216-206-00 RES-CHIP 2.2K 5% 1/8W
R202 1-216-837-11 METAL CHIP 22K 5% 1/10W
R203 1-216-837-11 METAL CHIP 22K 5% 1/10W
R204 1-216-849-11 METAL CHIP 220K 5% 1/10W
R205 1-216-849-11 METAL CHIP 220K 5% 1/10W
R206 1-218-875-11 METAL CHIP 15K 0.5% 1/10W
R207 1-218-875-11 METAL CHIP 15K 0.5% 1/10W
R208 1-218-875-11 METAL CHIP 15K 0.5% 1/10W
R209 1-216-840-11 METAL CHIP 39K 5% 1/10W
R210 1-216-833-11 METAL CHIP 10K 5% 1/10W
R211 1-216-833-11 METAL CHIP 10K 5% 1/10W
R212 1-218-843-11 METAL CHIP 680 0.5% 1/10W
R213 1-216-833-11 METAL CHIP 10K 5% 1/10W
AMP
20
XM-554ZR
Ref. No. Part No. Description Remark
R214 1-216-837-11 METAL CHIP 22K 5% 1/10W
R251 1-216-222-00 RES-CHIP 10K 5% 1/8W
R252 1-216-841-11 METAL CHIP 47K 5% 1/10W
R253 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R254 1-216-218-11 RES-CHIP 6.8K 5% 1/8W
R255 1-218-883-11 METAL CHIP 33K 0.5% 1/10W
R256 1-218-883-11 METAL CHIP 33K 0.5% 1/10W
R257 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R258 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R259 1-216-809-11 METAL CHIP 100 5% 1/10W
R260 1-216-809-11 METAL CHIP 100 5% 1/10W
R261 1-216-845-11 METAL CHIP 100K 5% 1/10W
R262 1-216-845-11 METAL CHIP 100K 5% 1/10W
R263 1-218-843-11 METAL CHIP 680 0.5% 1/10W
R264 1-216-813-11 METAL CHIP 220 5% 1/10W
R265 1-216-833-11 METAL CHIP 10K 5% 1/10W
R266 1-216-182-00 RES-CHIP 220 5% 1/8W
R267 1-216-134-00 RES-CHIP 2.2 5% 1/8W
R268 1-216-134-00 RES-CHIP 2.2 5% 1/8W
R269 1-205-991-11 ENCAPSULATED COMPONENT 0.1X2 5W
R270 1-216-833-11 METAL CHIP 10K 5% 1/10W
R271 1-218-893-11 METAL CHIP 82K 0.5% 1/10W
R272 1-249-385-11 CARBON 2.2 5% 1/4W F
R273 1-216-837-11 METAL CHIP 22K 5% 1/10W
R274 1-216-837-11 METAL CHIP 22K 5% 1/10W
R275 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R276 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R277 1-218-875-11 METAL CHIP 15K 0.5% 1/10W
R278 1-216-833-11 METAL CHIP 10K 5% 1/10W
R301 1-216-206-00 RES-CHIP 2.2K 5% 1/8W
R302 1-216-837-11 METAL CHIP 22K 5% 1/10W
R303 1-216-837-11 METAL CHIP 22K 5% 1/10W
R304 1-216-849-11 METAL CHIP 220K 5% 1/10W
R305 1-216-849-11 METAL CHIP 220K 5% 1/10W
R306 1-218-875-11 METAL CHIP 15K 0.5% 1/10W
R307 1-218-875-11 METAL CHIP 15K 0.5% 1/10W
R308 1-218-853-11 METAL CHIP 1.8K 0.5% 1/10W
R309 1-216-833-11 METAL CHIP 10K 5% 1/10W
R310 1-216-833-11 METAL CHIP 10K 5% 1/10W
R311 1-218-853-11 METAL CHIP 1.8K 0.5% 1/10W
R312 1-218-843-11 METAL CHIP 680 0.5% 1/10W
R313 1-216-833-11 METAL CHIP 10K 5% 1/10W
R314 1-216-837-11 METAL CHIP 22K 5% 1/10W
R351 1-216-222-00 RES-CHIP 10K 5% 1/8W
R352 1-216-841-11 METAL CHIP 47K 5% 1/10W
R353 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R354 1-216-218-11 RES-CHIP 6.8K 5% 1/8W
R355 1-218-883-11 METAL CHIP 33K 0.5% 1/10W
R356 1-218-883-11 METAL CHIP 33K 0.5% 1/10W
R357 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R358 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R359 1-216-809-11 METAL CHIP 100 5% 1/10W
R360 1-216-809-11 METAL CHIP 100 5% 1/10W
R361 1-216-845-11 METAL CHIP 100K 5% 1/10W
R362 1-216-845-11 METAL CHIP 100K 5% 1/10W
R363 1-218-843-11 METAL CHIP 680 0.5% 1/10W
R364 1-216-813-11 METAL CHIP 220 5% 1/10W
R365 1-216-833-11 METAL CHIP 10K 5% 1/10W
Ref. No. Part No. Description Remark
R366 1-216-182-00 RES-CHIP 220 5% 1/8W
R367 1-216-134-00 RES-CHIP 2.2 5% 1/8W
R368 1-216-134-00 RES-CHIP 2.2 5% 1/8W
R369 1-205-991-11 ENCAPSULATED COMPONENT 0.1X2 5W
R370 1-216-833-11 METAL CHIP 10K 5% 1/10W
R371 1-218-893-11 METAL CHIP 82K 0.5% 1/10W
R372 1-249-385-11 CARBON 2.2 5% 1/4W F
R373 1-216-837-11 METAL CHIP 22K 5% 1/10W
R374 1-216-837-11 METAL CHIP 22K 5% 1/10W
R375 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R376 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R377 1-218-875-11 METAL CHIP 15K 0.5% 1/10W
R378 1-216-833-11 METAL CHIP 10K 5% 1/10W
R401 1-216-206-00 RES-CHIP 2.2K 5% 1/8W
R402 1-216-837-11 METAL CHIP 22K 5% 1/10W
R403 1-216-837-11 METAL CHIP 22K 5% 1/10W
R404 1-216-849-11 METAL CHIP 220K 5% 1/10W
R405 1-216-849-11 METAL CHIP 220K 5% 1/10W
R406 1-218-875-11 METAL CHIP 15K 0.5% 1/10W
R407 1-218-875-11 METAL CHIP 15K 0.5% 1/10W
R408 1-218-853-11 METAL CHIP 1.8K 0.5% 1/10W
R409 1-216-833-11 METAL CHIP 10K 5% 1/10W
R410 1-216-833-11 METAL CHIP 10K 5% 1/10W
R411 1-218-853-11 METAL CHIP 1.8K 0.5% 1/10W
R412 1-218-843-11 METAL CHIP 680 0.5% 1/10W
R413 1-216-833-11 METAL CHIP 10K 5% 1/10W
R414 1-216-837-11 METAL CHIP 22K 5% 1/10W
R451 1-216-222-00 RES-CHIP 10K 5% 1/8W
R452 1-216-841-11 METAL CHIP 47K 5% 1/10W
R453 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R454 1-216-218-11 RES-CHIP 6.8K 5% 1/8W
R455 1-218-883-11 METAL CHIP 33K 0.5% 1/10W
R456 1-218-883-11 METAL CHIP 33K 0.5% 1/10W
R457 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R458 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R459 1-216-809-11 METAL CHIP 100 5% 1/10W
R460 1-216-809-11 METAL CHIP 100 5% 1/10W
R461 1-216-845-11 METAL CHIP 100K 5% 1/10W
R462 1-216-845-11 METAL CHIP 100K 5% 1/10W
R463 1-218-843-11 METAL CHIP 680 0.5% 1/10W
R464 1-216-813-11 METAL CHIP 220 5% 1/10W
R465 1-216-833-11 METAL CHIP 10K 5% 1/10W
R466 1-216-182-00 RES-CHIP 220 5% 1/8W
R467 1-216-134-00 RES-CHIP 2.2 5% 1/8W
R468 1-216-134-00 RES-CHIP 2.2 5% 1/8W
R469 1-205-991-11 ENCAPSULATED COMPONENT 0.1X2 5W
R470 1-216-833-11 METAL CHIP 10K 5% 1/10W
R471 1-218-893-11 METAL CHIP 82K 0.5% 1/10W
R472 1-249-385-11 CARBON 2.2 5% 1/4W F
R473 1-216-837-11 METAL CHIP 22K 5% 1/10W
R474 1-216-837-11 METAL CHIP 22K 5% 1/10W
R475 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R476 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R477 1-218-875-11 METAL CHIP 15K 0.5% 1/10W
R478 1-216-833-11 METAL CHIP 10K 5% 1/10W
R801 1-216-198-11 RES-CHIP 1K 5% 1/8W
R802 1-216-206-00 RES-CHIP 2.2K 5% 1/8W
R803 1-216-198-11 RES-CHIP 1K 5% 1/8W
AMP
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Sony XM554ZR - XM Amplifier Manuel utilisateur
- Taper
- Manuel utilisateur
Documents connexes
-
Sony XM-554ZR Mode d'emploi
-
-
-
Sony XM-GTX6040 Le manuel du propriétaire
-
Sony XM4S Manuel utilisateur
-
-
Sony XM-ZR704 Mode d'emploi
-
-
Sony XM-S400D Mode d'emploi
-
Autres documents
-
Compaq NSZ2107STTUW Manuel utilisateur
-
iGuzzini R956 Guide d'installation
-
-
-
-
-
-
-
-