Wacker Neuson CRT48-33K DF Manuel utilisateur

Operator’s Manual

Notice d'emploi

Ride-On Trowel

Truelles à conducteur porté

CRT48-33K

CRT48-33K DF

Type

CRT48-33K, CRT48-33K DF

Document 5200004714

Date

0217

Version

05

Language EN-FR

5200004714

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

CRT 48-33K Foreword

wc_tx002044gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 If you are missing either of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Machine Item Number

CRT 48-33K 5200002353, 5200002354

CRT 48-33K DF 5200007686, 5200007687

wc_gr010110

Serial Number:

Foreword CRT 48-33K

4 wc_tx002044gb.fm

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and obser

ve all instructions

describe

d in this manu

al.

 Wacker Neuson expressly reserves the right to make technical modifications,

even

without notice, which improve the performance or safety standards of it

s

mac

hines.

 The information contained in this manual is based on machines manufactured

up until th

e time of publication. Wacker Neuson reserves the right to chan

ge

any p

ortion of this information without notice.

 The illustrations, parts, and procedures in this manual refer to Wacker Neuson

factory-installed components. Your machine may vary depending on the

require

ments of your specific region.

CALIFORNIA

Proposition

65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental

discharge of sparks or flames from the engine exhaust. Spark arresters are

qualified and rated by the United States Forest Service for this purpose. In order to

comply with local laws regarding spark arresters, consult the engine distributor or

the local Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

W

acker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet

the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

2017-CE-CRT48-33K-DF_en_FM10.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin 53051 USA

Product

Product category

Product function

Item number

CRT48-33K

Trowel

To smooth and finish semi-cured concrete

5200002354, 5200007687

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2014/30/EU, EN12649

Authorized Person for Technical Documents

Robert Raethsel, Wacker Neuson Produktion GmbH & Co. KG, Wackerstrasse 6,

85084 Reichertshofen, Germany

Menomonee Falls, WI, USA, 30.01.17

Original Declaration of Conformity

Keith Herr

Vice President and Managing Director

For Wacker Neuson

Scott Grahl

Manager, Product Engineering

For Wacker Neuson

Jeff Volden

Director, Product Engineering

For Wacker Neuson

Table of Contents

CRT 48-33K

wc_bo5200004710_05TOC.fm

7

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 11

1.1 Signal Words Used in this Manual ..................................................... 11

1.2 Machine Description and Intended Use ............................................. 12

1.3 Operating Safety ................................................................................ 13

1.4 Lifting and Transport Safety ............................................................... 14

1.5 Operator Safety while Using Internal Combustion Engines ............... 15

1.6 Liquid Propane (LP) Safety ................................................................ 16

1.7 Service Safety .................................................................................... 18

2 Labels 19

2.1 Label Locations .................................................................................. 19

2.2 Label Meanings .................................................................................. 21

3 Lifting and Transporting 28

3.1 Lifting the Machine ............................................................................. 28

3.2 Overview ............................................................................................ 28

3.3 Transporting the Machine ................................................................... 29

4 Operation 31

4.1 Preparing the Machine for First Use ................................................... 31

4.2 Break-in Period ................................................................................... 31

4.3 Recommended Fuel ........................................................................... 32

4.4 Recommended Fuel (Liquid Propane) ............................................... 33

4.5 Position of the Operator ..................................................................... 33

4.6 Control / Component Locations .......................................................... 34

4.7 Operator Presence System ................................................................ 35

4.8 Refueling the Machine ........................................................................ 36

4.9 Installing the Liquid Propane (LP) Cylinder ........................................ 37

4.10 Pressure Relief Valves ....................................................................... 39

4.11 Breaking In New Machines ................................................................. 40

4.12 Before Starting ................................................................................... 41

4.13 Starting the Machine .......................................................................... 41

4.14 Stopping the Machine ......................................................................... 42

Table of Contents

CRT 48-33K

wc_bo5200004710_05TOC.fm

8

4.15 Operating Guidelines ...........................................................................42

4.16 Steering ...............................................................................................43

4.17 Pitch Adjustment .................................................................................44

4.18 Using the Retardant Spray System .....................................................45

4.19 Replacing an Empty Liquid Propane (LP) Cylinder .............................46

4.20 Emergency Shutdown Procedure ........................................................47

5 Maintenance 48

5.1 Maintaining the Emission Control System ...........................................48

5.2 Periodic Maintenance—LP System .....................................................48

5.3 Periodic Maintenance Schedule ..........................................................49

5.4 Maintaining the Gearboxes .................................................................50

5.5 Control Linkage Lubrication .................................................................51

5.6 Control Arm Adjustment (Forward or Backward) .................................51

5.7 Steering Assist System .......................................................................52

5.8 Right-hand Control Arm Adjustment (Right or Left) .............................53

5.9 Adjusting the Blade Arms ....................................................................53

5.10 Installing or Changing the Blades ........................................................54

5.11 Mounting Float Pans ...........................................................................56

5.12 Replacing the Drive Belt ......................................................................58

5.13 Jump-Starting the Machine .................................................................59

5.14 Maintaining the Spark Plugs ................................................................61

5.15 Servicing the Air Cleaner .....................................................................62

5.16 Checking the Engine Oil ......................................................................63

5.17 Engine Oil and Filter ............................................................................64

5.18 Maintaining the Fuel Filter ...................................................................66

5.19 Replacing the LP Lockoff / Filter Cartridge ..........................................67

5.20 Cleaning the Machine ..........................................................................69

5.21 Long-Term Storage .............................................................................70

5.22 Machine Disposal / Decommissioning .................................................71

5.23 Battery Disposal ..................................................................................72

6 Troubleshooting 73

6.1 Troubleshooting the Machine ..............................................................73

6.2 Troubleshooting the LP System ..........................................................74

7 Technical Data 75

7.1 Engine .................................................................................................75

7.2 Engine power rating ............................................................................75

Table of Contents

CRT 48-33K

wc_bo5200004710_05TOC.fm

9

7.3 Machine .............................................................................................. 76

7.4 Sound and Vibration Specifications .................................................... 77

8 AEM Safety Manual 79

9 Emission Control Systems

Information and Warranty—Gasoline 93

9.1 Emission Control System Background Information ............................ 93

9.2 Limited Defect Warranty for Exhaust Emission Control System ......... 94

9.3 Limited Defect Warranty for Wacker Neuson Evaporative

Emission Control Systems ................................................................. 94

10 Schematics 98

10.1 Electrical Schematic ........................................................................... 99

10.2 Electrical Schematic Components .................................................... 100

Table of Contents

CRT 48-33K

wc_bo5200004710_05TOC.fm

10

CRT 48–33K Safety Information

wc_si000713gb.fm 11

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f

To avoid death or serious injury from this type of hazard, obey all safety messages that

follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f

To avoid possible death or serious injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

CAUTION!

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f

To avoid possible minor or moderate injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

Safety Information CRT 48–33K

12 wc_si000713gb.fm

1.2 Machine Description and Intended Use

This machine is a ride-on concrete finishing trowel. The Wacker Neuson Ride-On

Trowel consists of a frame onto which are mounted a gasoline or diesel engine, a

fuel tank, a water tank, two gearboxes joined by a drive shaft, and an operator’s

platform with controls and a seat. A set of metal blades is connected to each

gearbox. A ring guard surrounds the blades. The engine rotates the blades via the

gearboxes and a clutch mechanism. The rotating blades ride on the surface of

curing concrete, creating a smooth finish. The operator, who sits on the operator’s

platform, uses the controls and the throttle pedal to control speed and direction of

the machine.

This machine is intended to be used for floating and burnishing curing concrete.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

 Using the machine as a ladder, support, or work surface

 Using the machine to carry or transport passengers or equipment

 Using the machine to finish inappropriate materials such as slurries, sealers, or

epoxy finishes

 Operating the machine outside of factory specifications

 Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

 Heat, noise, exhaust, and carbon monoxide from the engine

 Chemical burns from the curing concrete

 Fire hazards from improper refueling techniques

 Fuel and its fumes, fuel spillage from improper lifting technique

 Personal injury from improper lifting techniques

 Cutting hazards from sharp or worn blades

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

CRT 48–33K Safety Information

wc_si000713gb.fm 13

1.3 Operating Safety

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

 have received instruction on how to properly use the machine

 are familiar with required safety devices

The machine must not be accessed or operated by:

 children

 people impaired by alcohol or drugs

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

Operating

safety

To increase operating safety while running this machine:

 Do not touch the engine or muffler while the engine is on or immediately after it

has been stopped. These areas get hot and may cause burns.

 Do not use accessories or attachments that are not recommended by Wacker

Neuson. Damage to equipment and injury to the user may result.

 Do not leave the machine running unattended.

 Do not use a cell phone or send text messages while operating this machine.

Always do the following:

 Operate the machine with all safety devices and guards in place and in working

order.

 Remain aware of moving parts and keep hands, feet, and loose clothing away

from the moving parts of the machine.

Storing the

machine

 Store the machine properly when it is not being used. The machine should be

stored in a clean, dry location out of the reach of children.

 Close the fuel valve when the machine is not being operated.

\\

WARNING

Machines operated improperly or by untrained personnel can be hazardous.

f Read the operating instructions contained in both this Operator’s Manual and

the engine owner’s manual.

f Familiarize yourself with the location and proper use of all controls.

f Inexperienced operators should receive instruction from someone familiar with

the machine before being allowed to operate it.

Safety Information CRT 48–33K

14 wc_si000713gb.fm

1.4 Lifting and Transport Safety

Requirements

Before lifting the machine:

 refer to Technical Data for the operating weight of the machine

 make sure the lifting devices have sufficient capacity to lift the machine safely

 make sure the winch, forklift, or crane to be used for lifting the machine is in

operable condition and designed for such work

Lifting and

transporting

 Refer to Lifting and Transporting The Machine for detailed instructions.

CRT 48–33K Safety Information

wc_si000713gb.fm 15

1.5 Operator Safety while Using Internal Combustion Engines

Operating

safety

When running the engine:

 Keep the area around exhaust pipe free of flammable materials.

 Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine. Do not run the machine if fuel leaks are present or the fuel lines are

loose.

When running the engine:

 Do not smoke while operating the machine.

 Do not run the engine near sparks or open flames.

 Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

 Do not operate a machine when its fuel cap is loose or missing.

 Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

Refueling

safety

When refueling the engine:

 Clean up any spilled fuel immediately.

 Refill the fuel tank in a well-ventilated area.

 Re-install the fuel tank cap after refueling.

 Use suitable tools for refueling (for example, a fuel hose or funnel).

When refueling the engine:

 Do not smoke.

 Do not refuel a hot or running engine.

 Do not refuel the engine near sparks or open flames.

Radiator

Safety

Do not remove the radiator cap when the engine is running or hot. The radiator

fluid is hot and under pressure and may cause severe burns!

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

Safety Information CRT 48–33K

16 wc_si000713gb.fm

1.6 Liquid Propane (LP) Safety

Handling LP

Observe the following safety instructions when handling LP.

 Use proper lifting techniques to prevent stress or strain injuries.

 LP cylinders are pressurized. To vent excess pressure, two relief valves exist in

the fueling system for this machine. Read and understand the topic “Relief

Valves” in the Operation chapter before operating the machine.

 Pressurized LP is extremely cold. Vapors can instantly freeze bare skin and

eyes. Always wear gloves and eye protection when handling LP cylinders.

 LP vapors are heavier than air. LP vapors may settle around you, reducing the

amount of oxygen necessary for breathing. Always handle LP cylinders in a

well-ventilated area.

 Do not use an LP cylinder if there is visible damage to the tank or valves.

 Use only LP cylinders that have been filled by a trained and authorized person.

Responding

to hazardous

situations

Follow the safety instructions below if a hazardous situation occurs while you are

operating this machine (for example: a fire, explosion, severe weather, etc.).

 Stop the engine.

 Remove the starting key.

 Leave the work area.

 Notify local emergency response services.

Storing and

Transporting

LP Cylinders

Follow the safety instructions below when storing and transporting LP cylinders.

 Store and transport LP cylinders in the upright position only.

 Do not drop LP cylinders or allow them to roll or bounce in transit.

 Do not store or transport LP cylinders in environments where the temperature

may reach 51°C (125°F), for example, in a closed truck bed.

 Empty LP cylinders may contain residual pressurized gas and must be stored

and transported under the same conditions as full LP cylinders.

This topic continues on the next page.

WARNING

Fire, asphyxiation, chemical burn, and explosion hazards. Liquid propane (LP)

presents special hazards during operation and fueling. Failure to follow the

warnings and safety standards could result in serious injury or death.

f Read and follow the safety instructions in the engine owner’s manual and the

safety guidelines below.

CRT 48–33K Safety Information

wc_si000713gb.fm 17

Continued from the previous page.

Replacing

Empty LP

Cylinders

Follow the safety instructions below when replacing empty LP cylinders.

 Only a person familiar with the process should replace empty LP cylinders.

 Replace empty LP cylinders only in a well-ventilated area.

 Do not replace empty LP cylinders near sparks or open flames.

 Do not replace empty LP cylinders while the engine is running.

 Do not allow LP cylinders to remain in direct sunlight for extended periods

during the replacement process.

 Ensure that the full LP cylinder is properly seated and fastened in the tank

clamps.

 Ensure that all hose connections are tight, and perform a leak test, before

opening the discharge valve.

Safety Information CRT 48–33K

18 wc_si000713gb.fm

1.7 Service Safety

A poorly maintained machine can become a safety hazard. Periodic maintenance

and occasional repairs are necessary in order for the machine to operate safely

and properly over a long period of time.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

Requirements

 Stop the machine and remove the key from machine before performing

maintenance or making repairs.

 Disconnect the battery before adjusting or maintaining the electrical equipment.

Servicing

safety

 Do not use gasoline or other types of fuels or flammable solvents to clean parts,

especially in enclosed areas. Fumes from fuels and solvents can become

explosive.

 Handle blades carefully. The blades can develop sharp edges which can cause

serious cuts.

 Keep the area around the muffler free of debris such as leaves, paper, cartons,

etc. A hot muffler could ignite the debris and start a fire.

Replacing

parts

 When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

 Keep the machine clean and labels legible. Replace all missing and hard-to-

read labels. Labels provide important operating instructions and alert the user to

dangers and hazards.

CRT 48-33K Labels

wc_si000649gb.fm 19

2 Labels

2.1 Label Locations

wc_gr010123

W

O

J

G

A

H

Y

M

MM

BB

K

Z

CC

M

BB

H

V

DD

FF

AA

Labels CRT 48-33K

20 wc_si000649gb.fm

wc_gr0010124

HH

GG

LL

H

Q

L

Q

H

M

BB

Z

F

T

S

R

B

D

KK

N

JJ

E

R

BB

M

La page charge ...

Wacker Neuson CRT48-33K DF Manuel utilisateur

Ce manuel convient également à

Wacker Neuson CRT48-33K DF Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents