Remington Chainsaw 100582-01, 100582-02, EL-7B Manuel utilisateur

CONTENTS

SECTION PAGE

Symbol Information............................................................2

Safety Warnings .................................................................3

Before Operating Chain Saw.......................................3

Kickback......................................................................3

Pushback and Pull-in ...................................................4

Chain Saw Operation ..................................................4

Maintenance and Storage of Chain Saw .....................4

Product Identiﬁcation .........................................................5

Chain Saw Names and Terms.............................................5

Unpacking...........................................................................6

Assembly ............................................................................6

Saw Chain Tension Adjustment .........................................7

Filling Oil Tank ..................................................................7

Operating Chain Saw..........................................................8

Extension Cords ..........................................................8

SECTION PAGE

Oiling Chain ................................................................8

Cutting With the Chain Saw........................................8

Chain Brake.................................................................8

Trimming a Tree..........................................................9

Felling a Tree ..............................................................9

Limbing a Tree ............................................................10

Bucking a Log .............................................................11

Cleaning and Maintenance .................................................12

Cleaning Saw Body .....................................................12

Care of Guide Bar .......................................................12

Sharpening Your Saw Chain .......................................12

Storage ................................................................................14

Replacement Parts ..............................................................14

Troubleshooting..................................................................15

Warranty Information ......................................... Back Cover

IMPORTANT

Read and understand this manual before assembling or operating this chain saw.

Improper use of saw can cause severe injury. Keep this manual for future reference.

®

OWNER’S MANUAL

ELECTRIC CHAIN SAW

CANADIAN

®

MODEL 100582-01, 100582-02, TYPE EL-7B

CHAIN BRAKE

2

101241

INFORMATION SYMBOLS

!

WARNING ICON G 001

Safety Information Warnings Appears Throughout

This Manual

Pay close attention to them. Below are definitions for the

safety information listed throughout this manual.

WARNING indicates a hazard which can cause severe

personal injury, death, or substantial property damage if

you ignore warning.

CAUTION indicates a hazard which will or can cause

minor personal injury or property damage if you ignore

warning.

This symbol illustrates the computed kickback angle

used as a measure of the reaction of a hand-held

chain saw without chain brake when subjected,

under simulated conditions, to a rotational kickback

impulse.

Hearing and Eye Protection Must Be Worn

Beware of Kickback

Hold Chain Saw with Both Hands

Remove Plug Immediately if Cable is Damaged or

Cut

Do Not Expose to Rain or Use in Wet Conditions

Read Instruction Manual

3

101241

!

WARNING ICON G 001

SAFETY WARNINGS

This saw has a chain brake. When kickback occurs, the front

hand guard is moved forward by the back of operator’s left

hand. This stops the saw chain quickly, reducing the chance of

serious injury.

Never hold the chain saw by the front hand guard.

Cause Of Kickback

Kickback may occur when nose or tip of guide bar touches an

object while chain is moving. If chain cutter catches on object,

a sudden reverse action will result. The guide bar will kick up

and back towards operator.

Kickback may also occur when wood pinches chain at guide

bar nose. A sudden reverse action will also result.

The following steps will reduce the risk of kickback:

• Use both hands to grip saw while saw is running. Use ﬁrm

grip. Thumbs and ﬁngers must wrap around saw handles.

• Keep all safety items in place on saw. Make sure they

work properly.

• Do not overreach or cut above shoulder height.

• Keep solid footing and balance.

• Stand slightly to left side of saw. This keeps your body

from being in direct line with chain.

• Do not let guide bar nose touch anything when chain is

moving (see Figure 1).

Read and understand all Safety Warnings on pages

3 and 4. Improper use of this chain saw can cause

severe injury or death from ﬁre, electrical shock,

body contact with moving chain, or falling wood.

Direction

90°

Quadrant

Do Not Let

Guide Bar Nose

Touch Here

Figure 1 - Kickback Hazard Example. Do Not Let Nose of

Guide Bar Touch Object While Chain is Moving

Continued

• Never try cutting through two logs at same time. Only cut

one log at a time.

•

Do not bury guide bar nose or try plunge cut (boring into

wood using guide bar nose).

• Watch for shifting of wood or other forces that may pinch

chain.

• Use extreme caution when re-entering a previous cut.

• Use low-kickback chain and guide bar supplied with this

chain saw. Only replace these parts with chains and guide

BEFORE OPERATING CHAIN SAW

1. Read and understand this owner’s manual before operating

chain saw.

2. Use chain saw for cutting wood only. Do not use for

cutting any non-wood items.

3. Only well-instructed adults should operate chain saw. Never

allow children to operate chain saw. First-time user should

obtain informed, practical instruction in addition to reading

this manual. Practice cutting logs on a saw horse or cradle.

4. Use only electrical voltage noted on model plate of chain saw.

5. Use only extension cords marked for outdoor use. See

page 8 for extension cord requirements.

6. Do not operate chain saw

• while under the inﬂuence of alcohol, medication, or drugs

• in rain or in damp or wet areas

• where highly ﬂammable liquids or gases are present

• if saw is damaged, adjusted wrong, or not fully assembled

• if trigger does not turn saw on and off. Chain must stop

moving when you release trigger. Have faulty switch

replaced by authorized service person.

• while tired or in a hurry

• while in tree or on a ladder unless trained to do so

7. Wear snug-ﬁtting clothes when operating chain saw. Do

not wear loose clothing or jewelry. They can get caught in

moving saw chain.

8. Wear the following safety gear when operating chain saw:

• heavy-duty gloves

(wear rubber gloves if working outdoors)

• steel-toed safety footwear with non-skid soles

•

eye protection such as safety glasses, goggles, or face screen

• safety hard hat

• ear mufﬂers or ear plugs

• hair covering to contain long hair

• face or dust mask (if working in dusty areas)

9. Before cutting, always provide the following:

• clear work area

• secure footing

• planned retreat path from falling tree

10.Inspect tree before cutting down. Make sure there are no

dead limbs or branches that may fall on you.

KICKBACK

!

WARNING ICON G 001

WARNING

Avoid Kickback. Kickback can cause you to lose

control of chain saw. Kickback can cause severe

injury or death.

Kickback Safety Devices On This Saw

This saw has a low-kickback chain and reduced-kickback

guide bar. Both items reduce the chance of kickback. Kick-

back can still occur with this saw. Do not let tip of guide bar

touch anything when chain is moving.

4

101241

!

WARNING ICON G 001

SAFETY WARNINGS

Continued

7. Secure wood you are cutting by using clamps or chocks.

8. Grip chain saw ﬁrmly with both hands. Never operate chain

saw with one hand. Never use hand guard as handle.

9. Keep ﬁnger off trigger until ready to make cut.

10. Before starting chain saw, make sure chain is not touch-

ing anything.

11. Avoid body contact with grounded objects such as pipes,

wire fences, and metal posts.

12. Keep all parts of body away from chain when saw is running.

13. Do not force chain saw while cutting. Apply light pressure.

14. Cut small brush and saplings with extreme care. Slender

material may catch in chain and be whipped toward you.

This could also pull you off balance.

15. When cutting limb or tree trunk that is under tension, use

extreme caution. Be alert for wood springing back. When

wood tension is released, limb could spring back and

strike operator causing severe injury or death.

16. Do not activate the chain brake to stop saw. Always

release trigger to stop saw.

17. Carry chain saw from one place to another

• with chain saw unplugged

• by holding front handle (never use front hand guard as

handle)

• with ﬁnger off trigger

• with guide bar and chain to rear

• with scabbard in place

MAINTENANCE AND STORAGE OF CHAIN SAW

1. Unplug chain saw from power source

• when not in use

• before moving from one place to another

• before servicing

• before changing accessories or attachments

2. Inspect chain saw before and after each use. Check saw

closely if guard or other part has been damaged. Check

for any damage that may affect operator safety or

operation of saw. Check for alignment or binding of

moving parts. Check that switch turns motor on and off.

Check chain brake. Check for broken or damaged parts.

Do not use chain saw if damage affects safety or opera-

tion. Have damage repaired by authorized service person.

3. Maintain chain saw with care.

• Never expose saw to rain.

• Keep chain sharp, clean, and lubricated.

• Follow steps outlined in this manual to sharpen chain.

• Keep handles dry, clean, and free of oil.

• Keep all screws and nuts tight.

• Inspect power cord often. If damaged, have repaired by

authorized service person.

• Never carry chain saw by power cord.

• Never yank power cord to unplug it.

• Keep power cord from heat, oil, and sharp edges.

• Inspect extension cords often and replace if damaged.

4. When servicing, use only identical replacement parts.

5. Always store chain saw

• in a high or locked place, out of children’s reach

• in a dry place

• in a carrying case or with scabbard over guide bar

Keep this manual for reference. It is your guide to safe and

proper operation of this chain saw.

bars listed in this manual.

• Never use dull or loose chain. Keep chain sharp and

tensioned correctly.

Saw Maintenance and Kickback Safety

Follow maintenance instructions in this manual. Proper

cleaning of saw and chain and guide bar maintenance can

reduce chances of kickback. Inspect and maintain saw after

each use. This will increase the service life of your saw.

Note:

Even with proper sharpening, risk of kickback can increase

with each sharpening.

PUSHBACK AND PULL-IN

Cause Of Pushback and Pull-In

Pushback may occur while cutting with top of guide bar.

Pushback will force saw back towards you. Pull-in may occur

while cutting with bottom of guide bar. Pull-in will force saw

in towards wood you are cutting. These hazards can occur if

chain is pinched, caught, or contacts a non-wood object.

The following steps will reduce the risk of pushback or pull-in:

• Use both hands to grip saw while saw is running. Use ﬁrm

grip. Thumbs and ﬁngers must wrap around saw handles.

• Do not overreach or cut above shoulder height.

• Keep solid footing and balance.

• Stand slightly to left side of saw. This keeps your body

from being in direct line with chain.

• Have saw running at full speed before starting a cut.

• When cutting, make sure spike of saw is against wood

(pull-in only). See Product Identification, page 5, to locate

spike.

• Never try cutting through two logs at same time. Only cut

one log at a time.

• Watch for shifting of log or other forces that may pinch

chain.

• Use extreme caution when re-entering a previous cut.

• Do not twist saw when removing guide bar from undercut.

• Use wedges made of plastic, wood, or light alloy (never steel

or iron) to hold cut open.

CHAIN SAW OPERATION

1. Stay alert. Use common sense while operating chain saw.

2. Keep work area clean. Cluttered areas invite injuries.

3. Be aware of extension cord while operating chain saw. Be

careful not to trip over cord.

4. Keep children, animals, and bystanders away from chain

saw and extension cord. Only chain saw user should be in

work area.

5. Do not cut down a tree unless you are trained or have

expert help.

6. If two or more persons perform bucking and felling

operations at the same time, provide plenty of distance

between operations. Provide distance of at least twice the

height of tree being felled.

!

WARNING ICON G 001

WARNING

Avoid pushback and pull-in. These hazards can

cause you to lose control of chain saw.

Pushback or pull-in can cause severe injury.

5

101241

PRODUCT IDENTIFICATION

Power Cord

Rear

Handle

Rear Hand

Guard

Spike

Saw

Chain

Guide Bar

Nose

Guide Bar

Oil Level Sight Hole

(located on saw body,

hidden by front handle)

Front

Handle

Motor

Housing

Trigger

Guide Bar Metal bar that extends from saw body. The guide

bar supports and guides chain.

Guide Bar Nose Tip or end of guide bar.

Kickback Quick backward and upward motion of guide bar.

Kickback may occur when tip of guide bar touches an object

while chain is moving. The guide bar will kick up and back

towards operator.

Limbing Process of cutting limb(s) from a felled tree.

Low-Kickback Chain Chain that reduces chance of

kickback as required by CSA Standard Z62.3.

Normal Cutting Position Stance used while making

bucking and felling cuts.

Notching Cut Notch cut in tree that directs fall of tree.

Oiler Control System for oiling guide bar and chain.

Power Head Chain saw without chain and guide bar. Also

known as saw body.

Pushback (Kickback, Pinch) Rapid pushback of chain

saw. Pushback may occur if chain along top of guide bar is

pinched, caught, or contacts a foreign object.

Rear Handle Handle located at rear of saw body.

Reduced Kickback Guide Bar Guide bar that reduces

chance of kickback.

Replacement Chain Chain that complies with CSA

Standard Z62.3. when used with a speciﬁc saw. It may not

meet CSA Standard requirements when used with other saws.

Saw Chain (Chain) Loop of chain having cutting teeth for

cutting wood. The motor drives chain. The guide bar supports

chain.

Spiked Bumper (Spike) Pointed teeth at front of saw body

beside guide bar. Keep spiked bumper in contact with wood

when felling or bucking. It helps maintain position of saw

while cutting.

Sprocket Toothed wheel that drives chain.

Switch Device that completes or interrupts electrical circuit

to motor of saw.

Switch Linkage This device connects switch to trigger. It

moves switch when you squeeze trigger.

Switch Lockout Device that reduces accidental starting of

saw.

Trigger Device that turns saw on and off. Squeezing trigger

turns saw on. Releasing trigger turns saw off.

Trimming (Pruning) Process of cutting limb(s) from a

living tree.

Undercut An upward cut from underside of log or limb. This

is done while in normal cutting position and cutting with top of

guide bar.

Figure 2 - Electric Chain Saw

CHAIN SAW NAMES AND TERMS

Bucking Process of cutting a felled tree or log into lengths.

Felling Process of cutting down a tree.

Felling Cut Final cut when felling a tree. Make this cut on

opposite side of tree from notching cut.

Front Hand Guard Shield between front handle and guide

bar. Protects left hand while using saw. When kickback occurs,

the front hand guard is moved forward by the back of

operator’s left hand. This stops the saw chain quickly, reducing

the chance of serious injury.

Front Handle Located at front of saw body.

Switch

Lockout

Oil Cap

Front Hand

Guard/

Chain Brake

6

101241

!

WARNING ICON G 001

WARNING

Cutting edges on chain are sharp. Use protective

gloves when handling chain.

Figure 3 - Assembling Guide Bar, Chain, and Hand Guard

Adjusting

Block

Adjusting

Screw

Sprocket

Support

Adjusting

Plate

Figure 4 - Part Locations for Assembling Guide Bar

ASSEMBLY

UNPACKING

1. Remove all items from carton.

2. Check all items for any shipping damage. If you ﬁnd any

damage or if any parts are missing, promptly inform

dealer where you bought chain saw.

IMPORTANT

Do not clamp chain saw in vise during assembly.

1. Lay chain out ﬂat.

2. Remove guide bar nuts from guide bar bolts (see Figure 3).

3. Turn adjusting screw counterclockwise (see Figure 4).

Continue to turn adjusting screw until adjusting block is to

rear of adjusting plate.

4. Install guide bar onto saw body. Place rear of guide bar

between adjusting plate and sprocket support.

IMPORTANT:

Make sure to insert adjusting block into

oval adjusting hole on guide bar.

5. Attach guide bar nuts to guide bar bolts.

IMPORTANT:

Tighten guide bar nuts ﬁnger tight only.

Make sure adjusting block is in oval adjusting hole on

guide bar.

6. Place chain around drive sprocket, then along top groove

of guide bar and around guide bar nose.

Note:

Make sure

cutting edges of chain are facing the right direction.

Position chain so cutting edges on top of guide bar face

guide bar nose (see Figure 3).

!

WARNING ICON G 001

CAUTION

Do not place chain on saw backwards. If chain is

backwards, saw will vibrate badly and will not cut.

7. Adjust saw chain tension. Follow steps under Saw

Chain Tension Adjustment, page 7.

Drive

Sprocket

Guide Bar

Bolts

Saw

Chain

Guide

Bar

Adjusting

Hole

Guide Bar

Nuts

Cutting

Edge

Towards

Guide

Bar Nose

Sprocket

Support

7

101241

SAW CHAIN TENSION

ADJUSTMENT

Guide Bar

Nuts

Guide Bar

Correct

Tension

Gap

Guide Bar

Incorrect Tension

Figure 6 - Saw Chain Adjustment

Note:

For pre assembled models, the saw chain tension is

properly set at factory. A new chain will stretch. Check new

chain after first few minutes of operation. Allow chain to cool

down. Follow steps below to readjust saw chain tension.

1. Before adjusting chain, make sure guide bar nuts are only

ﬁnger tight (see Figure 3, page 6). Also make sure adjust-

ing block is in oval adjusting hole on guide bar (see Figure

3 and 4, page 6).

2. Turn adjusting screw clockwise until all slack is out of

chain (see Figure 5).

Note:

There should be no gap between side links of chain

and bottom of guide bar (see Figure 6).

3. Wearing protective gloves, move chain around guide bar.

Chain should move freely. If chain does not move freely,

loosen chain by turning adjusting screw counterclockwise.

4. After chain tension is correct, tighten guide bar nuts ﬁrmly.

If not, guide bar will move and loosen chain tension. This

will increase the risk of kickback. This can also damage

saw.

Note:

A new chain will stretch. Check new chain

after ﬁrst few minutes of operation. Allow chain to cool

down. Readjust chain tension.

Figure 5 - Turning Adjusting Screw

!

WARNING ICON G 001

WARNING

Unplug chain saw from power source before

adjusting saw chain tension.

!

WARNING ICON G 001

WARNING

Cutting edges on chain are sharp. Use protective

gloves when handling chain.

!

WARNING ICON G 001

WARNING

Maintain proper chain tension always. A loose

chain will increase the risk of kickback. A loose

chain may jump out of guide bar groove. This

may injure operator and damage chain. A loose

chain will cause chain, guide bar, and sprocket

to wear rapidly.

FILLING OIL TANK

1. Remove oil cap.

2. Fill oil tank with SAE #30 motor oil.

Note:

For tempera-

tures below -1°C, use SAE #10 oil. For temperatures above

24°C, use SAE #40 oil.

3. Replace oil cap at once. Tighten oil cap ﬁrmly for good

seal. This will avoid oil seepage from tank.

4. Wipe off excess oil.

Note:

It is normal for oil to seep when saw is not in use.

Empty oil tank, tighten oil cap, and store upside down after

each use to prevent seepage.

8

101241

EXTENSION CORDS

Use proper extension cord with this chain saw. Use only

extension cords marked for outdoor use. Use an extension cord

no less than 1.5 mm

2

(14SWG) at distances up to 30 meters

(100 feet). The cord must be marked with suffix W-A follow-

ing the cord type marking.

Example

: SJTW-A

Use an extension cord heavy enough to carry the current your

saw will draw. An undersized cord will cause a voltage drop at

the saw, loss of power, and overheating.

Keep cord away from cutting area. Make sure cord does not

catch on branches or logs during cutting. Inspect cords often.

Replace damaged cords.

The extension cord may come undone from the power cord

during use. To avoid this, make a knot with the two cords as

shown in Figure 7 below.

!

WARNING ICON G 001

WARNING

Read and understand this owner’s manual

before operating this saw. Make certain you read

and understand all Safety Warnings. Improper

use of this chain saw can cause severe injury or

death from ﬁre, electrical shock, or body contact

with moving chain, or falling wood.

OPERATING CHAIN SAW

4. Make sure your footing is ﬁrm. Keep feet apart. Divide

your weight evenly on both feet. Stand slightly to left side

of saw. This keeps your body from being in direct line

with chain.

5. When ready to make a cut, press in switch lockout with

right thumb and squeeze trigger (see Figure 9). This will

turn saw on. Releasing trigger will turn saw off. Make sure

saw is running at full speed before starting a cut.

Figure 8 - Pressing Oil Cap to Oil Chain

6. When starting a cut, place moving chain against wood.

Hold saw ﬁrmly in place to avoid possible bouncing or

skating (sideways movement) of saw.

7. Guide saw using light pressure. Do not force saw. The

motor will overload and can burn out.

8. Remove saw from a cut with saw running at full speed.

Stop saw by releasing trigger. Do not use the chain brake.

Make sure chain has stopped before setting saw down.

9. Practice until you can maintain a steady, even cutting rate.

OILING CHAIN

Always check oil level before using saw. To oil chain, press oil

cap. Oil will feed onto guide bar and chain. Press oil cap at

least once before each cut. Check oil level often by looking at

oil sight level hole. Oil sight level hole is on left side of saw,

between front handle and front hand guard.

Figure 7 - Tying Extension Cord and Power Cord in Knot

To reset chain brake, release trigger and move front hand

guard back into position. You must release trigger first. If not,

the saw will start when you reset the front hand guard.

Note:

Test chain brake before each use. Firmly grip saw with

both hands. With saw running, move front hand guard forward

with back of left hand. Keep both hands on the handles. Saw

chain should stop. If chain brake does not work, have saw

repaired by authorized service person.

CAUTION: Do not use the chain brake to stop and

start your saw. Quick repeated stops may cause

overheating of the chain brake. Damage to the chain

brake will occur.

CUTTING WITH THE CHAIN SAW

1. Connect saw to extension cord. Connect extension cord to

power supply.

2. Make sure section of log to be cut is not laying on ground.

This will keep chain from touching ground as it cuts

through log. Touching ground with moving chain will dull

chain.

3. Use both hands to grip saw. Always use left hand to grip

front handle and right hand to grip rear handle. Use ﬁrm

grip. Thumbs and ﬁngers must wrap around saw handles

(see Figure 9).

Trigger

Figure 9 - Front Hand Guard, Switch Lockout,

and Trigger Location

Front Hand

Guard

Switch

Lockout

CHAIN BRAKE

The chain brake quickly stops the saw chain. Kickback causes

the back of operator’s left hand to contact front hand guard

(see Figure 10). When front hand guard moves forward, the

saw chain stops. This reduces the chance of serious injury

during kickback. When the chain brake activates, release

trigger at once.

STOP

Figure 10 - The chain brake quickly stopping the saw

chain

Extension

Cord

Chain Saw

Power Cord

9

101241

OPERATING CHAIN SAW

Continued

TRIMMING A TREE (Pruning)

Trimming a tree is the process of cutting limbs from a living

tree. Make sure your footing is ﬁrm. Keep feet apart. Divide

your weight evenly on both feet. Follow directions below to

trim a tree.

1. Make ﬁrst cut 15 centimeters (six inches) from tree trunk

on underside of limb. Use top of guide bar to make this

cut. Cut 1/3 through diameter of limb (see Figure 11).

2. Move five to ten centimeters (two to four inches) farther

out on limb. Make second cut from above limb. Continue

cut until you cut limb off.

3. Make third cut as close to tree trunk as possible on

underside of limb stub. Use top of guide bar to make this

cut. Cut 1/3 through diameter of stub.

4. Make fourth cut directly above third cut. Cut down to meet

third cut. This will remove limb stub.

!

WARNING ICON G 001

WARNING

Do not cut limbs higher than your shoulders.

3rd Cut - Stub Undercut

(to avoid splintering)

5 to 10 cm (2" to 4")

1st Cut - Pruning Undercut

(to avoid splintering)

4th Cut - Final

Stub Cut

2nd Cut - Pruning Cut

(to avoid pinching)

Figure 11 - Cutting A Limb

!

WARNING ICON G 001

CAUTION

Seek professional help if facing conditions

beyond your ability.

Direction of Fall

Retreat

Path

45°

Retreat

Path

Tree

Figure 12 - Retreat Path From Tree

Continued

Felling is the process of cutting down a tree. Make sure your

footing is ﬁrm. Keep feet apart. Divide your weight evenly on

both feet. Follow directions below to fell a tree.

Before Felling a Tree

1. Before felling, inspect tree. Make sure there are no dead

limbs or branches that may fall on you. Study natural lean

of tree, location of larger branches, and wind direction.

This will help you judge which way tree will fall.

2. Clear work area around tree.

3. Plan and clear a retreat path before felling. Make retreat

path opposite to planned direction of fall of tree and at 45°

angle (see Figure 12).

4. Remove dirt, stones, loose bark, nails, staples, and wire

from tree where you will make felling cuts.

5. Stay on uphill side when felling tree. Tree could roll or

slide downhill after falling.

FELLING A TREE (Cutting Down a Tree)

!

WARNING ICON G 001

WARNING

Do not operate chain saw while

• in a tree

• on a ladder or any other unstable surface

• in any awkward position

You may lose control of saw causing severe injury.

!

WARNING ICON G 001

WARNING

Avoid kickback. Kickback can result in severe

injury or death. See

Kickback

, page 3 to avoid

risk of kickback.

!

WARNING ICON G 001

CAUTION

Seek professional help if facing conditions

beyond your ability.

15 cm

(6")

!

WARNING ICON G 001

WARNING

• Avoid kickback. Kickback can result in severe

injury or death. See

Kickback

, page 3 to avoid

risk of kickback.

• Do not fell a tree without ample skill or expert

help.

• Keep children, animals, and bystanders away

from area when felling a tree.

• If two or more persons perform bucking and

felling operations at the same time, provide

ample distance between operations. Provide

distance of at least twice the height of tree

being felled.

!

WARNING ICON G 001

WARNING

When felling a tree, be aware of your surroundings.

Do not endanger any person, strike utility lines, or

cause property damage. If tree strikes utility lines,

contact utility company at once.

10

101241

OPERATING CHAIN SAW

Continued

Figure 14 - Limbing A Tree

Limbing is removing branches from a fallen tree. Make sure

your footing is ﬁrm. Keep feet apart. Divide your weight

evenly on both feet. Do not remove larger limbs under tree that

support log off ground. Remove each limb with one cut (see

Figure 14). Clear cut limbs from work area often. This will

help maintain a safe work area.

Make sure you start your cut where limb will not pinch saw

during cutting. To avoid pinching, start cut on freely hanging

limbs from above limb. Start cut on limbs under tension from

under limb. If pinch occurs, turn saw off, lift limb, and remove

saw.

Felling Procedure

Felling Notch

A properly placed felling notch will determine direction tree

will fall. Place felling notch on side of tree in direction you

want tree to fall (see Figure 13). Follow directions below to

create a felling notch.

1. Make lower notch cut as close to ground as possible. Hold

saw so guide bar is horizontal. Cut 1/3 the diameter of tree

trunk (see Figure 13).

Note:

Always make this horizontal

lower notch cut ﬁrst. If you make this cut second, tree can

pinch chain or guide bar.

2. Start upper notch cut the same distance above ﬁrst cut as

ﬁrst cut is deep.

Example:

If lower notch cut is 20 centimeters deep (eight

inches), start upper notch cut 20 centimeters (eight inches)

above it. Cut downward at 45° angle. The upper notch cut

should meet end of lower notch cut (see Figure 13).

3. Remove tree trunk wedge created by notching cuts.

Felling Cut

1. Make felling cut five centimeters (two inches) higher than

lower notch cut and on opposite side of tree (see Figure

13). Keep felling cut parallel to lower notch cut.

2. Cut towards notch.

4. When tree begins to fall, quickly

• remove saw from felling cut

• release trigger to turn saw off

• put saw down

• exit area using retreat path

!

WARNING ICON G 001

WARNING

Be alert for falling overhead limbs. Watch your

footing while exiting area.

LIMBING A TREE

!

WARNING ICON G 001

WARNING

Do not cut all the way through tree. Leave about

five centimeters (two inches) of tree diameter

uncut directly behind felling notch (see Figure

13). This uncut portion acts as a hinge. The hinge

helps keep tree from twisting and falling in wrong

direction.

Figure 13 - Felling A Tree

3. As felling cut nears hinge, tree should begin to fall.

Note:

If

needed, drive wedges into felling cut to control direction of

fall. If tree settles back and pinches chain, drive wedges into

felling cut to remove saw. Only use wedges made of wood,

plastic, or aluminum. Never use wedge made of steel. This

could cause kickback and damage to chain.

Hinge

3rd Cut -

Felling Cut

2nd Cut -

Upper

Notch Cut

1st Cut -

Lower

Notch Cut

!

WARNING ICON G 001

WARNING

Avoid kickback. Kickback can result in severe

injury or death. See

Kickback

, page 3 to avoid

risk of kickback.

!

WARNING ICON G 001

WARNING

When cutting limb that is under tension, use

extreme caution. Be alert for wood springing

back. When wood tension is released, limb could

spring back and strike operator causing severe

injury or death.

!

WARNING ICON G 001

CAUTION

Seek professional help if facing conditions

beyond your ability.

Direction of Fall

5 cm

(2 inches)

5 cm

(2 inches)

11

101241

OPERATING CHAIN SAW

Continued

2nd Cut

1st Cut

Figure 16 - Bucking Log When Log Is Supported

On One End

1st Cut

2nd Cut

Figure 17 - Bucking Log When Log Is Supported

On Both Ends

Log Supported On One End

1. Make ﬁrst cut on underside of log (see Figure 16). Use top

of guide bar to make this cut. Cut 1/3 through diameter of

log. This cut will keep section from splintering when cut.

2. Make second cut directly above ﬁrst cut. Cut down to meet

ﬁrst cut. This cut will keep log from pinching guide bar

and chain.

Log Supported On Both Ends

1. Make ﬁrst cut from above log (see Figure 17). Cut 1/3

through diameter of log. This cut will keep section from

splintering when cut.

2. Make second cut on underside of log, directly under ﬁrst

cut. Use top of guide bar to make this cut. Cut up to meet

ﬁrst cut. This will keep log from pinching guide bar and

chain.

BUCKING A LOG

Bucking a log is cutting a log into sections. Make sure your

footing is ﬁrm. Keep feet apart. Divide your weight evenly on

both feet. Stand slightly to left of saw. This keeps your body

from being in direct line with chain. When possible, raise log

or section off ground. Do this by using limbs, logs, chocks, etc.

When cutting through log, maintain control by reducing

cutting pressure near end of cut. Do not relax your grip on

chain saw handles. Do not let moving chain touch ground.

Ground will dull moving chain. After cutting through log,

release trigger to turn saw off before moving saw.

Follow directions below to buck a log.

Entire Length Of Log On Ground

Cut log from top (see Figure 15).

Figure 15 - Bucking Log With Entire Length On Ground

!

WARNING ICON G 001

WARNING

Avoid kickback. Kickback can result in severe

injury or death. See

Kickback

, page 3 to avoid

risk of kickback.

!

WARNING ICON G 001

WARNING

• If on slope, make sure log will not roll down

hill. Secure log by using wooden stakes. Drive

wooden stakes into ground on downhill side

of log. Stand on uphill side of log while

cutting. Log may roll after cutting.

• Never try cutting through two logs at same

time. This could increase the risk of kickback.

• While cutting log, never hold log with your

hand, leg, or foot.

• While cutting log, never allow another person

to hold log.

• Turn off and unplug saw before moving from

one place to another.

!

WARNING ICON G 001

CAUTION

Seek professional help if facing conditions

beyond your ability.

12

101241

CLEANING SAW BODY

Keep saw body clean. Use a soft cloth dampened with a mild

soap and water mixture. Wipe saw body to clean.

CARE OF GUIDE BAR

Uneven bar wear causes most guide bar problems. Incorrect

sharpening of chain cutter and depth gauge settings often cause

this. When bar wears unevenly, it widens guide bar groove (see

Figure 18). This causes chain clatter and rivet popping. Saw

will not cut straight. Replace guide bar if this occurs.

Inspect guide bar before sharpening chain. A worn or damaged

guide bar is unsafe. A worn or damaged guide bar will damage

chain. It will also make cutting harder.

CLEANING AND MAINTENANCE

NOTICE

Below are instructions for servicing your chain

saw. Any servicing not mentioned below should

be done by an authorized service person.

!

WARNING ICON G 001

WARNING

Unplug chain saw from power source before

servicing. Severe injury or death could occur

from electrical shock or body contact with

moving chain.

!

WARNING ICON G 001

WARNING

Cutting edges on chain are sharp. Use protective

gloves when handling chain.

Normal Guide Bar

Guide Bar With

Uneven Wear

Figure 18 - Guide Bar Cross Section Showing

Uneven Bar Wear

Guide Bar

Groove

Guide Bar

Normal Guide Bar Maintenance

1. Remove guide bar from chain saw.

2. Remove sawdust from guide bar groove periodically. Use

putty knife or wire.

3. Clean oil slots after each day of use.

4. Remove burrs from sides of guide bar. Use ﬂat ﬁle to make

side edges square.

Replace guide bar when

• bar is bent or cracked

• inside groove of bar is badly worn

Note:

When replacing guide bar, see Replacement Parts, page

14 for proper bar.

!

WARNING ICON G 001

WARNING

When cleaning saw body,

• do not submerge saw in any liquids

• do not use products that contain ammonia,

chlorine, or abrasives

• do not use chlorinated cleaning solvents,

carbon tetrachloride, kerosene, or gasoline

SHARPENING YOUR SAW CHAIN

Keep chain sharp. Your saw will cut faster and more safely. A

dull chain will cause undue sprocket, guide bar, chain, and

motor wear. If you must force chain into wood and cutting

creates only sawdust with few large chips, chain is dull.

Items Needed to Sharpen Chain

Purchase these items from your local dealer, hardware store, or

chain saw supplies outlet.

• 4 mm (5/32") round ﬁle • Depth gauge tool

• File guide • Vise

• Medium sized ﬂat ﬁle

Cleaning Groove

With Putty Knife

Oil Slot

Flat File

Burr

Guide

Bar

Figure 19 - Guide Bar Maintenance

!

WARNING ICON G 001

WARNING

Unplug chain saw from power source before

servicing. Severe injury or death could occur

from electrical shock or body contact with

moving chain.

!

WARNING ICON G 001

WARNING

Cutting edges on chain are sharp. Use protective

gloves when handling chain.

13

101241

CLEANING AND MAINTENANCE

Continued

Sharpening Cutters

Use ﬁle guide for 30° ﬁling.

1. Adjust chain for proper tension (see Saw Chain Tension

Adjustment, page 7).

2. Clamp guide bar in vise to hold saw steady.

Note:

Do not

clamp chain.

3. Press four millimeter (5/32") round ﬁle (attached to ﬁle

guide) into groove between top plate and depth gauge on

chain. File guide should rest on both top plate and depth

gauge (see Figures 20 and 21).

Note:

File at midpoint of

guide bar.

4. Hold ﬁle guide level. Make sure 30° mark on ﬁle guide is

parallel to center of guide bar (see Figure 20). This will

insure that you ﬁle cutters at 30° angle.

5. File from inside towards outside of cutter until sharp.

Only ﬁle in this one direction (see Figure 20).

Note:

Two

or three strokes with ﬁle should sharpen cutter.

6. After each cutter if sharpened, move chain forward to

sharpen next cutter. File all cutters on one side of chain.

7. Move to other side of chain and repeat process.

Top Plate

(left side

of chain)

Groove

Depth Gauge

(left side

of chain)

Groove

Depth Gauge

(right side of chain)

Top Plate

(right side of chain)

Left Side

of Chain

Right Side

of Chain

Figure 21 - Chain Part Locations

Flat File

Depth

Gauge

Tool

Depth Gauge

Depth

Gauge

Slot

Figure 22 - Depth Gauge Tool On Chain

Continued

ECSp005

Figure 23 - Round Off Front Corner Of Depth Gauge

Front Corner

After several hand ﬁlings, have authorized service center or

sharpening service machine sharpen chain. This will insure

even ﬁling.

Filing Cutter Depth Gauges

The cutter depth gauge clearance is reduced as cutters are

sharpened. After every second or third sharpening, reset cutter

depth gauges.

1. Place depth gauge tool ﬁrmly across top of two cutters.

Make sure depth gauge enters slot in depth gauge tool (see

Figure 22).

2. Use medium ﬂat ﬁle. File depth gauge level with depth

gauge tool.

3. Remove depth gauge tool. With ﬂat ﬁle, round off front

corner of cutter depth gauge (see Figure 23).

F

IL

E

H

O

LD

E

R

30° Guide

Mark

File Guide

4 mm (5/32")

Round File

Note: This

illustration

shows ﬁle

guide place-

ment and ﬁling

direction for

sharpening

cutters on left

side of chain.

Filing

Direction

Figure 20 - File and File Guide Placement On Chain

14

101241

CLEANING AND MAINTENANCE

Continued

STORAGE

If storing saw for more than 30 days, follow steps below.

1. Drain oil tank.

2. Remove and clean guide bar and chain. Clean guide bar

and chain by soaking in petroleum based solvent or mild

soap and water mixture.

3. Dry guide bar and chain.

4. Place chain in container ﬁlled with oil. This will prevent

rust.

5. Wipe a thin coating of oil over surface of guide bar.

6. Wipe off outside of saw body. Do this with soft cloth

dampened with a mild soap and water mixture.

7. Store chain saw

• in a high or locked place, out of children’s reach

• in a dry place

• in a carrying case or with scabbard over guide bar

• with oil cap tight and saw upside down to prevent

excess oil seepage

Replacing Saw Chain

Replace chain when cutters are too worn to sharpen or when

chain breaks. Only use replacement chain noted in this manual.

Always include new drive sprocket when replacing chain. This

will maintain proper driving of chain.

Note:

For proper chain

and drive sprocket, see Replacement Parts, below.

REPLACEMENT PARTS

!

WARNING ICON G 001

WARNING

Use only replacement parts described in this

manual. Use of other parts could damage saw or

injure operator.

Purchase these parts from your local dealer.

Part Number Description

097572-03S Guide bar, 400 mm (16")

091375S Chain, 400 mm (16")

097570-01 Guide bar, 355 mm (14")

091374S Chain, 355 mm (14")

075752 Drive sprocket

079417-03 Wrench/Screwdriver

15

101241

TROUBLESHOOTING

OBSERVED FAULT

Saw runs, but does not cut.

Saw does not cut unless heavily forced.

Cutting produces only sawdust with few

large chips.

Saw runs slow. Saw stalls easily.

Motor of saw does not run when you

squeeze trigger.

Motor of saw runs, but chain does not

move.

Chain does not get oil.

Chain comes off guide bar.

Saw smokes.

Saw leaks oil.

Chain brake does not stop saw chain.

POSSIBLE CAUSE

Chain assembled backwards on guide

bar.

Chain is dull.

Low power supply voltage.

Switch lockout not pressed in to release

trigger.

Chain brake activated.

Extension cord connections

loose.

Open line fuse or circuit

breaker.

Bad motor brushes.

Open wiring circuit on saw.

Gear train failure.

Clogged oil slot in guide bar.

Oil is too thick.

Chain is loose.

Guide bar and chain not assembled

right.

Saw damaged. Do not use saw.

Oil cap is not secure.

Brake failure.

!

WARNING ICON G 001

WARNING

Unplug chain saw from power source before servicing. Severe injury

or death could occur from electrical shock or body contact with

moving chain.

REMEDY

See Assembly, page 6.

See Sharpening Your Saw Chain,

page 12.

Extension cord wire size too

small. See Extension Cords, page 8.

Press in switch lockout before squeez-

ing trigger.

Release trigger and move front hand

guard back towards rear of saw.

Check cord connections.

Check line fuse or circuit

breaker.

Contact authorized service person.

Remove guide bar and clean oil slot.

Use correct weight of oil. See Filling

Oil Tank, page 7.

Tighten chain. See Saw

Chain Tension Adjustment, page 7.

See Assembly, page 6.

Contact authorized service person.

Tighten oil cap.

Note:

Empty oil tank

when not in use.

Contact authorized service person.

16

101241

NOTES

_____________________________________________________________________________

17

101241

NOTES

_____________________________________________________________________________

101241-01

REV. C

10/94

WARRANTY INFORMATION

KEEP THIS WARRANTY

Always specify model and serial numbers when writing the factory.

We reserve the right to amend these speciﬁcations at any time without notice. The only warranty applicable is our

standard written warranty. We make no other warranty, expressed or implied.

This product is warranted to be free from defects in materials and workmanship for six (6) months from the date

of first purchase when operated and maintained in accordance with instructions. This warranty is extended only

to the original retail purchaser.

This warranty covers only the cost of parts and labor required to restore this to proper operating condition.

Transportation and incidental costs associated with warranty repairs are not reimbursable under this warranty.

Warranty service is available only through authorized dealers or service centres.

This warranty does not cover commercial or rental usage nor defects resulting from misuse, accidents, lack of

proper maintenance, bar, chain.

The warrantor assumes no responsibility for indirect, incidental or consequential damages.

THIS EXPRESS WARRANTY IS GIVEN IN LIEU OF ANY OTHER WARRANTY EITHER EXPRESSED

OR IMPLIED, INCLUDING WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICU-

LAR PURPOSE.

LIMITED WARRANTY

ELECTRIC CHAIN SAW

Model ___________________________________

Serial No. ________________________________

Date Purchased ___________________________

DESA Industries of Canada, Inc.

2220 Argentia Road

Unit #4

Mississauga, Ontario

L5N 2K7

905-826-8010

Fax 905-826-8236

TABLE DES MATIÈRES

SECTION PAGE

Description des symboles................................................2

Avertissements pour la sécurité ...................................... 3

Avant d’utiliser la tronçonneuse .............................. 3

Recul ........................................................................3

Poussée et traction....................................................4

Utilisation de la tronçonneuse ................................. 4

Entretien et remisage de la tronçonneuse ................5

Nomenclature des pièces.................................................6

Vocabulaire de la tronçonneuse ...................................... 6

Déballage......................................................................... 7

Assemblage .....................................................................7

Réglage de la tension de la chaîne ..................................8

Remplissage du réservoir d’huile ...................................8

Utilisation de la tronçonneuse......................................... 9

Prolongateurs de cordon ..........................................9

SECTION PAGE

Lubrification de la chaîne ........................................ 9

Sciage avec la tronçonneus ......................................9

Frein de chaîne .......................................................10

Taille d’un arbre (élagage).....................................10

Abattage d’un arbre................................................11

Ébranchage.............................................................12

Tronçonnage d’une bille ........................................13

Nettoyage et entretien ...................................................14

Nettoyage du carter de tronçonneuse.....................14

Entretien de la lame-guide .....................................14

Affûtage de la chaîne .............................................15

Remisage ....................................................................... 16

Pièces de rechange ........................................................16

Dépannage .....................................................................17

Information sur la garantie........................ couverture dos

IMPORTANT

Il est recommandé de lire et comprendre ce manuel avant d’assembler cette tronçonneuse

et de l’utiliser. L’utilisation incorrecte de la tronçonneuse risque d’entraîner des blessures

graves. Conserver ce manuel pour pouvoir s’y référer ultérieurement.

CANADIEN

®

TRONÇONNEUSE ÉLECTRIQUE

MANUEL D’UTILISATION ET D’ENTRETIEN

MODÈLE 100582-01, 100582-02, TYPE EL-7B

FREIN DE CHAÎNE

®

2

101241

DESCRIPTION SYMBOLES

Lire le manuel d’instructions.

Ne pas exposer à la pluie ni utiliser en conditions

humides.

Si le cordon est endommagé ou coupé, débrancher

immédiatement de la prise de courant.

Tenir la tronçonneuse des deux mains.

Attention au recul.

Porter des protections pour les oreilles et les yeux.

Des avertissements concernant la sécurité figurent

dans ce manuel.

Bien les observer. Leurs définitions sont les suivantes:

AVERTISSEMENT indique un risque pouvant entraîner

des blessures graves, la mort ou des dégâts matériels

importants si l’on ne tient pas compte de la mise en

garde.

ATTENTION indique un risque entraînant ou pouvant

entraîner des blessures légères ou des dégâts matériels

si l’on ne tient pas compte de la mise en garde.

Ce symbole illustre l’angle de recul calculé utilisé

comme mesure de la réaction d’une tronçonneuse

sans frein de chaîne lorsqu’elle est soumise, en

simulation, à une impulsion de recul rotative.

!

WARNING ICON G 001

La page charge ...

Remington Chainsaw 100582-01, 100582-02, EL-7B Manuel utilisateur

Ce manuel convient également à

Remington Chainsaw 100582-01, 100582-02, EL-7B Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents