Samsung 1011516 Manuel utilisateur

Refrigerator

User manual

RF30KM*

Free Standing Appliance

RF30KMED_DA68-02894B-01_EN.indd 1 2016-03-30  12:55:53

02 English

Contents

SETTING UP YOUR FRENCH DOOR REFRIGERATOR ……………………………………………… 09

OPERATING YOUR FRENCH DOOR REFRIGERATOR ………………………………………………… 17

TROUBLESHOOTING ……………………………………………………………………………………… 33

RF30KMED_DA68-02894B-01_EN.indd 2 2016-03-30  12:55:53

English 03

Safety information

SAFETY INFORMATION

Before using your new Samsung French

Door Refrigerator, please read this manual

thoroughly to ensure that you know how to

operate the features and functions that your

new appliance offers safely and efﬁciently.

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory, or mental capabilities, or

those who lack experience and knowledge,

unless they have been given supervision or

instruction concerning the use of the appliance

by a person responsible for their safety.

Because the following instructions cover various

models, the characteristics of your refrigerator

may differ slightly from the refrigerator described

in this manual. If you have any question,

contact us at 1-800-SAMSUNG or ﬁnd help

and information online at www.samsung.com.

Important safety symbols and

precautions:

WARNING

Hazards or unsafe practices that may

result in severe personal injury or death.

CAUTION

Hazards or unsafe practices that may result in

minor personal injury or property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions carefully.

Unplug the power plug

from the wall socket.

Make sure the refrigerator is grounded

to prevent electric shock.

Call the contact center for help.

Note.

These warning symbols are here to

prevent injury to you and others.

Please follow them carefully.

After reading this section, keep it in

a safe place for future reference.

WARNING

STATE OF CALIFORNIA

PROPOSITION 65 WARNING

(US ONLY)

• This product contains chemicals known to the

State of California to cause cancer and birth

defects or other reproductive harm.

WARNING

CRITICAL INSTALLATION

WARNINGS

• Do not install the refrigerator in a damp

location or place where it may come in

contact with water.

- Deteriorated insulation on electrical parts may

cause an electric shock or fire.

• Do not place this refrigerator in direct sunlight

or expose it to the heat from stoves, room

heaters, or other appliances.

• Do not plug several appliances into the same

multiple power strip. The refrigerator should

always be plugged into its own individual

electrical outlet which has a voltage rating that

matches the voltage listed on the refrigerator’s

rating plate.

- This provides the best performance and

also prevents overloading house wiring

circuits, which could cause a fire hazard from

overheated wires.

• If the wall socket is loose, do not insert the

power plug.

- There is a risk of electric shock of fire.

• Do not use a cord that shows cracks or

abrasion damage along its length or at either

end.

RF30KMED_DA68-02894B-01_EN.indd 3 2016-03-30  12:55:53

04 English

• Do not bend the power cord excessively or

place heavy articles on it.

• Do not twist or tie the power cord.

• Do not hook the power cord over a metal

object, place a heavy object on the power

cord, insert the power cord between objects,

or push the power cord into the space behind

the appliance.

- When moving the refrigerator, be careful not to

roll over or damage the power cord

- This may result in an electric shock or fire.

• Never unplug your refrigerator by pulling on the

power cord. Always grip the plug firmly and

pull straight out from the outlet.

- Damage to the cord may cause a short-circuit,

fire, and/or electric shock.

• Do not use aerosols near the refrigerator.

- Using aerosols near the refrigerator may cause

an explosion or fire.

• Do not install this appliance near a heater or

inflammable material.

• Do not install this appliance in a humid, oily or

dusty location, in a location exposed to direct

sunlight and water (rain drops).

• Do not install this appliance in a location where

gas may leak.

- This may result in an electric shock or fire.

• This refrigerator must be properly

located and installed in accordance with

the instructions in this manual before

you use it.

• Connect the power plug in the proper position

with the cord hanging down.

- If you connect the power plug upside down,

the wire can get cut off and cause a fire or

electric shock.

• When moving the refrigerator, be careful not to

roll over or damage the power cord.

- This constitutes a fire hazard.

• Make sure that the power plug is not

squashed or damaged by the back of the

refrigerator.

• Keep the packing materials out of reach of

children.

- There is a risk of death from suffocation if a

child puts the packing materials on his or her

head.

• The appliance must be positioned so that the

plug is accessible after installation.

- Failing to do so may result in an electric shock

or fire due to electric leakage.

• You need to remove all the protective plastic

film before you initially plug the product in.

• The instructions include the following wording

regarding the use of extension cords:

“WARNING - Improper use of the grounding

plug can result in a risk of electric shock. If it is

necessary to use an extension cord, use only

a 3-wire extension cord that has a 3-blade

grounding plug and a 3-slot receptacle that will

accept the plug on the appliance. The marked

rating of the extension cord should be AC 115-

120 V, 10 A, or more. If a grounding adapter

is used, make sure the receptacle box is fully

grounded.”

• The refrigerator must be safely

grounded.

- Always make sure that you have grounded the

refrigerator before attempting to investigate

or repair any part of the appliance. Power

leakages can cause severe electric shock.

• Never use gas pipes, telephone lines, or other

potential lightning attractors as an electrical

ground.

- Improper use of the grounding plug can result

in a risk of electric shock. If it is necessary

to use an extension cord, use only a 3-wire

extension cord that has a 3-blade grounding

plug and a 3-slot receptacle that will accept

the plug on the appliance. The marked rating

of the extension cord should be AC115-

120V, 10A, or more. If a grounding adapter

is used, make sure the receptacle box is fully

grounded.

• Plug the power plug into the wall socket firmly.

Do not use a damaged power plug, damaged

power cord or loose wall socket.

- This may result in an electric shock or fire.

• Do not modify the refrigerator. Unauthorized

modifications can cause safety problems. To

reverse an unauthorized modification, we will

charge the full cost of parts and labor.

• If the power cord is damaged,

have it replaced immediately by the

manufacturer or one of its service agent.

CAUTION

INSTALLATION CAUTIONS

• Allow sufficient space around the

refrigerator and install it on a flat surface.

• Keep the ventilation space in the appliance

enclosure or mounting structure clear of

obstructions.

RF30KMED_DA68-02894B-01_EN.indd 4 2016-03-30  12:55:53

English 05

• Allow the appliance to stand for 2 hours before

loading foods after installation and turning on.

• We strongly recommend you use a qualified

technician or service company to install the

refrigerator.

- Failing to do so may result in an electric shock,

fire, explosion, problems with the product, or

injury.

WARNING

CRITICAL USAGE WARNINGS

• Do not insert the power plug into a wall

socket with wet hands.

• Do not store articles on the top of the

appliance.

- When you open or close the door, the articles

may fall and cause personal injury and/or

material damage.

• Do not insert hands, feet or metal objects

(such as knives, etc.) into the bottom or the

back of the refrigerator.

- This may result in an electric shock or injury.

- Any sharp edges may cause a personal injury

• Do not put a container filled with water on the

refrigerator.

- If spilled, there is a risk of fire or electric shock.

• Children should be supervised to ensure that

they do not play with the appliance.

- Keep ﬁngers out of “pinch point” areas.

Clearances between the doors and cabinet are

necessarily small. Be careful when you open

the doors when children are in the area.

• Do not let children hang on the door. A serious

injury may occur.

• Do not let children go inside the refrigerator.

Children could become trapped.

• Do not insert your hands into the bottom area

under the appliance.

- Any sharp edges may cause personal injury.

• Do not let children step on a drawer cover.

- The drawer may break and cause them to slip.

• Do not overfill the refrigerator with food.

- When you open the door, an item may fall out

and cause personal injury or material damage.

• Do not touch the inside walls of the freezer or

products stored in the freezer with wet hands.

- This may cause frostbite.

• Never put fingers or other objects into the

water dispenser hole, ice chute, or ice maker

bucket.

- It may cause personal injury or material damage.

• Do not use or place any substances sensitive

to temperature such as inflammable sprays,

inflammable objects, dry ice, medicine, or

chemicals near or inside of the refrigerator.

• Do not keep volatile or inflammable objects or

substances (benzene, thinner, propane gas,

alcohol, ether, LP gas and other such products

etc.) in the refrigerator.

- This refrigerator is for storing food only.

- This may result in fire or explosion.

• Do not store pharmaceutical products,

scientific materials, or temperature sensitive

products in the refrigerator.

- Products that require strict temperature

controls must not be stored in the refrigerator.

• Do not place or use an electrical appliance

inside the refrigerator, unless it is of a type

recommended by the manufacturer.

• Do not stand on top of the appliance or place

objects (such as laundry, lighted candles,

lighted cigarettes, dishes, chemicals, metal

objects, etc.) on the appliance. This may result

in an electric shock, fire, problems with the

product, or injury. Do not put a container filled

with water on the appliance.

- If spilled, there is a risk of fire or electric shock.

• Do not use mechanical devices or any other

means to accelerate the defrosting process,

other than those recommended by the

manufacturer.

• Do not damage the refrigerant circuit.

• Do not spray volatile material such as

insecticide onto the surface of the appliance.

- As well as being harmful to humans, it may

also result in an electric shock, fire or problems

with the product.

• Do not attempt to repair, disassemble,

or modify the appliance yourself.

• Do not use any fuse (such as cooper, steel

wire, etc.) other than the standard fuse.

• If your appliance needs to be repaired or

reinstalled, contact your nearest service center.

- Failing to do so may result in an electric shock,

fire, problems with the product, or injury.

• If the interior or exterior LED lamp has gone

out, please contact your nearest service

center.

• Children should be supervised to ensure

that they do not play with the appliance.

• Bottles should be stored tightly together so

that they do not fall out.

• This product is intended only for the storage of

food in a domestic environment.

RF30KMED_DA68-02894B-01_EN.indd 5 2016-03-30  12:55:53

06 English

• If a gas leak is detected, avoid any naked

flames or potential sources of ignition and air

the room in which the appliance is standing for

several minutes.

- Do not touch the appliance or power cord.

- Do not use a ventilating fan.

- A spark may result in explosion or fire.

• Use only the LED Lamps provided by the

manufacturer or its service agents.

• If the refrigerator emits a burning smell

or smoke, unplug the refrigerator

immediately and contact your Samsung

Electronics service center.

• If you experience difficulty changing a non-LED

light, contact a Samsung service energy.

• If the product is equipped with LED Lamps, do

not disassemble the Lamp Covers and LED

Lamps yourself.

- Please contact your service agents.

• If dust or water enters the refrigerator, unplug

the refrigerator and contact your Samsung

Electronics service center.

- Otherwise there is a risk of fire.

CAUTION

USAGE CAUTIONS

• Do not re-freeze frozen foods that

have thawed completely. Do not place

carbonated or fizzy drinks in the freezer

compartment. Do not put bottles or

glass containers in the freezer.

- When the contents freeze, the glass may break

and cause personal injury.

• Use only the ice maker provided with the

refrigerator.

• Have the refrigerator’s water supply connected

only to a potable water supply. To operate

the ice maker properly, water pressure of 20

~ 125psi is required. If you will be away from

home for a long period of time (on vacation, for

example) and won’t be using the water or ice

dispensers, close the water valve.

- Otherwise, water leakage may occur.

• If you won’t be using the refrigerator for a very

long period of time, (3 weeks or more) empty

the refrigerator including ice bucket, unplug it,

close the water valve, wipe excess moisture

from the inside walls, and leave the doors

open to prevent odors and mold.

• Service Warranty and Modification.

- Any changes or modifications

performed by a 3rd party on this

finished appliance are not covered

under Samsung warranty service, nor is

Samsung responsible for safety issues

that result from 3rd party modifications.

• Do not block the air vents inside the

refrigerator.

- If the air vents are blocked, especially with

a plastic bag, the refrigerator can be over

cooled. If this cooling period lasts too long,

the water filter may break and cause water

leakage.

• If the refrigerator is disconnected from the

power supply, you should wait for at least five

minutes before plugging it back in.

• If you have a long vacation planned or do not

intend to use the refrigerator for a long period

of time, empty the refrigerator including ice

bucket, pull out the power plug, wipe excess

moisture from the inside walls, and leave the

doors open to prevent odors and mold.

• To get the best performance from the product:

- Do not place food too close to the vents at the

rear of the appliance as it can obstruct free air

circulation in the refrigerator compartment.

- Wrap food up properly or place it in airtight

containers before putting it into the refrigerator.

- Do not place glass or bottles or carbonated

beverages into the freezer.

The container may freeze and break, and this

may result in injury.

- Please observe maximum storage times and

expiration dates of frozen goods.

- There is no need to disconnect the refrigerator

from the power supply if you will be away for

less than three weeks. However, if you will be

away for more than three weeks, remove all

the food and ice in the ice bucket, unplug the

refrigerator, close the water valve, wipe excess

moisture from the inside walls, and leave the

doors open to prevent odors and mold.

• Fill the water tank, ice tray and water cubes

only with potable water (mineral water or

purified water).

- Do not fill the tank with tea or a Sports drink.

This may damage the refrigerator.

• Do not apply strong shock or excessive force

onto the surface of glass.

- Broken glass may result in a personal injury

and/or property damage.

• If the product is flooded, make sure to

contact your nearest service center.

- There is a risk of electric shock or fire.

RF30KMED_DA68-02894B-01_EN.indd 6 2016-03-30  12:55:53

English 07

CAUTION

CLEANING CAUTIONS

• Do not directly spray water on the inside

or outside the refrigerator.

- There is a risk of fire or electric shock.

• Do not use a hair dryer to dry the inside of the

refrigerator. Do not place a lighted candle in

the refrigerator to remove bad odors.

- This may result in an electric shock or fire.

• Remove any foreign matter or dust from

the power plug pins. Do not use a wet

or damp cloth when cleaning the plug.

- Otherwise, there is a risk of fire or electric

shock.

• Before cleaning or performing

maintenance, unplug the appliance from

the wall socket.

- Failing to do so may result in an electric shock

or fire.

WARNING

CRITICAL DISPOSAL

WARNINGS

• DANGER : Risk of child entrapment.

Before you throw away your old

refrigerator or freezer:

- Take off the doors and door latch.

- Leave the shelves in place so that children

cannot easily climb inside.

- Children trapped inside a refrigerator can hurt

themselves or suffocate to death.

• Please dispose of the packaging material from

this product in an environmentally friendly

manner.

• Ensure that none of the pipes on the back of

the appliance are damaged prior to disposal.

• R-600a or R-134a is used as a refrigerant.

Check the compressor label on the rear of

the appliance or the rating label inside the

fridge to see which refrigerant is used for your

refrigerator. If this product contains flammable

gas (Refrigerant R-600a), contact your local

authority in regard to safe disposal of this

product.

• When disposing of this refrigerator, remove

the door/door seals and door latch so that

small children or animals cannot become

trapped inside. Children should be supervised

to ensure that they do not play with the

appliance.

If trapped inside, the child may get hurt or

suffocate to death.

• Cyclopentane is used in the insulation. The

gases in the insulation material require a

special disposal procedure. Please contact

your local authorities in regard to the

environmentally safe disposal of this product.

• Keep all packaging materials well out of the

reach of children, as packaging materials can

be dangerous to children.

- If a child places a bag over his or her head, the

child could suffocate.

ADDITIONAL TIPS FOR

PROPER USAGE

• In the event of a power failure, call the local

office of your Electricity Company and ask how

long it is going to last.

- Most power failures that are corrected in an

hour or two will not affect your refrigerator

temperatures. However, you should minimize

the number of door openings while the power

is off.

- If the power failure lasts more than 24 hours,

remove and discard all frozen food.

• The appliance might not operate consistently

(frozen contents can thaw or temperatures

can become too warm in the frozen food

compartment) when sited for an extended

period of time in a location where ambient

air temperatures are constantly below the

temperatures for which the appliance is

designed.

• In case of particular foods, keeping it under

refrigeration can have a bad effect on

preservation due to its properties.

• Your appliance is frost free, which means there

is no need to manually defrost your appliance.

This will be carried out automatically.

• Temperature rise during defrosting complies

with ISO requirements. But If you want to

prevent an undue rise in the temperature of the

frozen food while the appliance defrosts, wrap

the frozen food in several layers of newspaper.

• Do not re-freeze frozen foods that have

thawed completely.

RF30KMED_DA68-02894B-01_EN.indd 7 2016-03-30  12:55:53

08 English

Saving Energy Tips

- Install the appliance in a cool, dry room with

adequate ventilation. Ensure that it is not

exposed to direct sunlight and never put

it near a direct source of heat (radiator, for

example).

- Not to block any vents and grilles is

recommended for energy efficiency.

- Allow warm food to cool down before placing

it in the appliance.

- Put frozen food in the refrigerator to thaw.

You can then use the low temperatures of the

frozen products to cool food in the refrigerator.

- Do not keep the door of the appliance open for

too long when putting food in or taking food

out. The shorter the time the door is open, the

less frost build-up you’ll have in the freezer.

- It is recommended to install the refrigerator

with clearance to the back and sides. This will

help reduce power consumption and keep

your energy bills lower.

RF30KMED_DA68-02894B-01_EN.indd 8 2016-03-30  12:55:53

English 09

01 SETTING UP

Setting up your French Door

Refrigerator

GETTING READY TO INSTALL

THE REFRIGERATOR

Congratulations on your purchase of this Samsung

French Door Refrigerator.

We hope you enjoy the state-of-art features and

efﬁciencies that this new appliance offers.

Selecting the best location for the

refrigerator

Choose :

• A location with easy access to a water supply.

• A location without direct exposure to sunlight.

• A location with a level floor.

• A location with enough space for the

refrigerator doors to open easily.

• A location that allows sufficient space to the

right, left, back and top for air circulation.

• A location that allows you to move the

refrigerator easily if it needs maintenance or

service.

• Do not install the refrigerator in locations where

the temperature is over 110 °F (43 °C) or

below 50 °F (10 °C ).

• Do not locate the refrigerator where it may

become wet.

If the refrigerator does not have enough space,

it can cause the bad inﬂuence to refrigeration

efﬁciency and power consumption.

If your refrigerator has an ice maker, allow extra

space at the back for the water line connections.

When you install the refrigerator next to a ﬁxed

wall, you need a minimum clearance of 3 ¾”

(95mm) between the refrigerator and wall to allow

the door to swing open.

Important : Make sure that you can easily move

your refrigerator to its ﬁnal location by measuring

doorways (both width and height), thresholds,

ceilings, stairways, etc.

The following chart details the exact height and

depth of this Samsung French Door Refrigerator.

AA

B

C

D

E

Depth “A” 35 1/2" (901mm)

Width “B” 35 3/4" (908mm)

Height “C” 68 7/8" (1749mm)

Overall Height “D” 70" (1777mm)

Depth “E” 37 7/8" (963mm)

62 1/8"

(1578mm)

13 1/4"

(335mm)

125° 125°

2"

(50mm)

35 3/4" (908mm)

30 7/8"

(785mm)

49 3/4" (1263mm)

4 3/4" (122mm)

2 3/8" (61mm)

54 3/8" (1383mm)

Each measurement based on the design

dimension, so it may differ depending on

the measuring method.

RF30KMED_DA68-02894B-01_EN.indd 9 2016-03-30  12:55:53

10 English

When moving your refrigerator

To prevent floor damage, be sure the front

adjusting legs are in the up position (above

the floor). Refer to ‘Adjusting the Level’ in

the manual (on page 14).

Flat-blade screw

driver(-)

Control Lever

FLOORING

For proper installation, you must place this

refrigerator on a level, hard surface that is the

same height as the rest of the ﬂoor. This surface

should be strong enough to support a fully loaded

refrigerator.

To protect the ﬁnish of the ﬂooring, cut a large

section of the cardboard carton and place it under

the refrigerator where you are working. When

moving the refrigerator, you need to pull and push

it straight forwards or back. Do not wiggle it from

side to side.

CAUTION

REMOVING THE

REFRIGERATOR DOORS

For some installations you need to remove the

fridge and freezer drawers so you can move the

refrigerator to its ﬁnal location. Do not remove

the doors/drawer if you don’t need to. If you

do not need to remove the refrigerator doors, go

to Adjusting the Level on page 14. If you need to

remove the doors. continue below.

Before removing the door/drawer, make sure you

read the following items:

Disconnect power to the refrigerator

before removing the door or drawer.

• Be careful not to drop, damage, or

scratch the doors/drawers while

removing them.

• Use care when you remove the doors/drawers.

The doors are heavy and you could injure

yourself.

• Reattach the doors/drawers properly to avoid:

- Moisture from air leakage.

- Uneven door alignment.

- Wasting energy due to improper door seal.

Disassemble the refrigerator doors

Be careful not to drop and scratch the

doors while removing them.

Required Tools (Not provided)

You need the following tools to complete the

installation of your refrigerator:

Philips

screwdriver(+)

Flat-blade screw

driver(-)

Socket wrench

(10mm)

Pliers

Allen wrench

(3/16”) (5mm)

WARNING

RF30KMED_DA68-02894B-01_EN.indd 10 2016-03-30  12:55:54

English 11

01 SETTING UP

With the door opened

1. Remove the 3 screws holding down the TOP

TABLE (1) and separate the connected wires.

1

2. Disconnect the two connectors (2) on the

left side door. To remove the water coupler

from the hinge, twist and pull it from the hinge.

Remove the water line (3) while pressing the

marked part (4) of the water line coupler.

2

3

4

3. Pull and remove the hinge lever (5). Remove

the ground screw (6) attached to the upper

left door hinges with a philips screwdriver (+).

Remove the upper left and right door hinges

(7).

5

6

7

4. Lift the door straight up to remove.

5. Remove the screw (8) attached to the

lower left and right door hinges with a philips

screwdriver (+). Remove the 2 hex head bolts

(9) attached to the lower left and right door

hinges with an allen wrench (3/16”). Remove

the lower left and right door hinges (10).

Allen wrench

10

8

9

RF30KMED_DA68-02894B-01_EN.indd 11 2016-03-30  12:55:55

12 English

RE-ATTACHING THE

REFRIGERATOR DOORS

To reattach the fridge doors after you have moved

the fridge to its ﬁnal location, assemble the parts

in reverse order.

1. The Water Line must be fully inserted into the

center of the transparent coupler (Type A)

or the Guide Lines (Type B) to prevent water

leakage from the dispenser.

Center of Transparent coupler

The Guide Lines

Dispenser

Type A Type B

DISASSEMBLING THE FLEX

DOOR

1. Take out the Flex Zone (1) by lifting it up.

1

2. Take off the cover (2) w/harness with a flat-

blade screwdriver (-).

2

3. Press the locking tab and separate the Wire

Connector.

When reassembling it, be sure to connect

the wire harness.

If it is not connected, the Flex Room does

not work.

4. Remove 1 hex head bolt from each side with a

socket wrench (10mm).

5. Lift up the Flex door from the rails.

Putting too much food into the freezer

drawers can prevent the freezer from

closing completely and can cause frost

build-up.

CAUTION

RF30KMED_DA68-02894B-01_EN.indd 12 2016-03-30  12:56:00

English 13

01 SETTING UP

RE-ASSEMBLING THE FLEX

DOOR

To reattach the flex doors, assemble parts in

reverse order.

Be sure to connect the Flex Door Wire

Connector.

If it is not connected, the Flex Room does

not work.

DISASSEMBLING THE

FREEZER DOOR

1. Take out the upper drawer by lifting it up.

2. Remove the freeze room guard ( 1 ) by lifting

the guard up.

3. Take out the lower

basket ( 2 ) by lifting

the basket up from

the rail system.

4. Press the fixing

hook of the rail

system.

CAUTION

5. Holding the top of the Freezer Drawer, pull it

out all the way, and then remove it from the rail

system.

Be careful not to scratch or dent the

sliding rail by letting it strike the floor.

Make sure that you mount the freezer

basket in the right position when removing

/ installing the freezer door. Failing to do

so may result in the door not opening or

closing properly.

Putting too much food into the freezer

drawers can prevent the freezer from

closing completely and can cause frost

build-up.

RE-ASSEMBLING THE

FREEZER DOOR

To reattach the drawer after you have moved

the fridge to its ﬁnal location, assemble the parts

in reverse order.

CAUTION

1

2

RF30KMED_DA68-02894B-01_EN.indd 13 2016-03-30  12:56:02

14 English

ADJUSTING THE LEVEL

Make sure the refrigerator is level so that you can

make final adjustments. Use a level to test if the

refrigerator is level both side to side and back to

front. If the refrigerator is not level, you will not

be able to get the doors perfectly even, which

may cause moisture condensation and increased

energy bills. Below is an example of how to level

the refrigerator if the left side of the refrigerator is

lower than the right side.

flat-blade screwdriver (-)

Control Lever

How to adjust the level

1. Open the freezer drawer and remove the lower

basket.

2. Insert a flat-blade screwdriver (-) into the notch

on the left control lever, and turn it counter-

clockwise to level the refrigerator. (You turn the

lever clockwise to lower the refrigerator and

counterclockwise to raise it.)

Both control levers must be touching the

floor to avoid possible personal injury or

property damage because of tipping.

If the right side is lower, perform the same

procedure, but with the right control lever.

It is difficult to remove the cover leg

front from the refrigerator, so we do not

recommend making small adjustments

with the control lever. Instead, refer to the

next page for the best way to make minor

adjustments to the doors.

CAUTION

MAKING MINOR

ADJUSTMENTS TO THE

DOORS

Remember, a leveled refrigerator is necessary

for getting the doors perfectly even. If you need

help, review the previous section on leveling the

refrigerator.

Adjustment

part

Fixed part

The left door is fixed. To make minor door

adjustments, adjust only the right door.

1. Pull out the flex door ( 1 ) to reveal the lower

hinge ( 2 ).

2. Insert a philips screwdriver (+) (3) into the

shaft (4) of the lower hinge.

3. Adjust the height by turning a philips

screwdriver (+) (3) clockwise (

DOWN

) or

counterclockwise (

UP

).

When you turn a philips screwdriver (+)

counterclockwise ( ), the door will

move up.

3

1

2

3

4

RF30KMED_DA68-02894B-01_EN.indd 14 2016-03-30  12:56:04

English 15

01 SETTING UP

INSTALLING THE WATER

DISPENSER LINE

A water dispenser with a ﬁlter is one of the helpful

features on your new refrigerator. To help promote

better health, the water ﬁlter removes unwanted

particles from your water. However, it does not

sterilize or destroy microorganisms. You may need

to purchase a water purifying system to do that.

The water line also connects to the ice maker.

For the ice maker to operate properly, water

pressure of 20-125 psi (138 ~ 862Kpa) is required.

If the refrigerator is installed in an area with low

water pressure (below 20psi), you can install

a booster pump to compensate for the low

pressure.

After you have connected the water line, make

sure the water storage tank inside the refrigerator

is properly ﬁlled. To do this, press the water

dispenser lever until the water runs from the water

outlet.

Water line installation kits are available at

extra cost from your dealer.

We recommend using a water line

installation kit that contains copper tubing

and ¼” compression nut.

Connecting to the water supply line

1. First, shut off the main water

supply.

2. Locate the nearest cold water drinking line and

install the pipe clamp and shut off valve.

3. Connect the water line installation kit to the

shut off valve.

Shut off valve

Pipe clamp

Cold water line

Water line installation kit

Connecting the water supply line to

the refrigerator.

There are several items that you need to purchase

to complete this connection.

You may ﬁnd these items sold as a kit at your local

hardware store.

Use Copper Tubing Use Plastic Tubing

• ¼” copper tubing

• ¼” compression nut

(1pc)

• Ferrule (2pc)

• ¼” plastic tubing

→ Molded end(Bulb)

• ¼” compression nut

(1pc)

Compression

Nut (1/4”)

(Assembled)

Ferrule

(Not supplied)

Plastic Tubing

(Assembled)

Compression

Fitting

(Assembled)

Molded

end(Bulb)

Compression

nut (A) (1/4”)

(Not supplied)

or

Copper tubing

(Not supplied)

Plastic tubing (B)

(Not supplied)

Household water supply line

Refrigerator

Pipe clamp

Cold water line

Shut off valve

RF30KMED_DA68-02894B-01_EN.indd 15 2016-03-30  12:56:05

16 English

1. Connect the household water line to the

assembled compression fitting.

- If you are using copper tubing, slip the

compression nut ( A ) (not supplied) and

ferrule (not supplied) on the copper tubing (not

supplied) as shown.

- If you are using plastic tubing ( B ) , insert the

molded end (Bulb) of the plastic tubing ( B )

into the compression fitting.

Do not use without the molded end (Bulb)

of the plastic tubing ( B ).

2. Tighten the compression nut ( A ) onto the

compression fitting.

Do not over-tighten the compression nut ( A ) .

3. Turn the water on and check for any leakage.

If you find water drops or leakage in the

connection areas, turn off the main water

supply. Check the connections and, if

necessary, tighten.

4. Flush 1 gallon of water through the filter

before drinking or using the water from the

refrigerator. (Flush approximately 6 minutes.)

To flush, press a large glass or cup against the

water dispenser lever. Fill the glass, empty it

into the kitchen sink after it is filled, and then

repeat.

5. After you turn on the refrigerator, let the ice

maker make ice for 1 to 2 days. Over that

period of time, throw out the first 1 or 2

buckets of ice the freezer makes to ensure all

impurities have been removed from the water

line.

Only connect the water line to a drinkable

water source.

If you have to repair or disassemble the water line,

cut off 1/4“ of the plastic tubing to make sure you

get a snug, leak-free connection.

You can test the water line quickly using a

paper cup. Under normal conditions, the

water dispenser can fill a 5.75 oz. (170cc)

cup in about 10 seconds.

CAUTION

Completing the Set Up

Now that you have your new refrigerator installed

in place, you are ready to set up and enjoy the

features and functions of the appliance. By

completing the following steps, your refrigerator

should be fully operational.

1. Make sure your refrigerator is in an appropriate

location with reasonable clearance between it

and the wall. Refer to installation instructions in

this manual.

2. Once the refrigerator is plugged in, make sure

the interior light comes on when you open the

doors.

3. Set the Temperature control to the coldest

temperature and wait for an hour. The freezer

will get slightly chilled and the motor will run

smoothly. Reset the refrigerator and freezer to

the temperatures you want.

4. After you plug the refrigerator in, it will

take a few hours to reach the appropriate

temperature. You can store food and drinks

in the refrigerator after the temperature is

sufficiently cool.

If condensation or water drops appears

on both sides of fridge door’s central

part, turn the Energy Saver mode off after

removing the condensation. (See the

explanation on Energy Saver button in the

USING THE CONTROL PANEL.)

RF30KMED_DA68-02894B-01_EN.indd 16 2016-03-30  12:56:05

English 17

02 OPERATING

Operating your French Door

Refrigerator

USING THE CONTROL PANEL

7

8 6

9

1

2

3

5

4

10

( 1 )

Freezer/

Power

Freeze

(3sec)

The Freezer button serves two purposes:

- To set the Freezer to your desired

temperature.

- To turn the Power Freeze function on

and off.

1) To set the Freezer temperature,

touch the Freezer button. You can set the

temperature between 5 °F (-15 °C) and

-8°F (-23 °C).

2) Power Freeze function

Touch and hold this button for 3 seconds

to decrease the time needed to freeze

products in the Freezer.

It can be helpful if you need to quickly

freeze easily spoiled items or if the

temperature in the freezer has warmed

dramatically (For example, if the door was

left open).

When you use this function, the energy

consumption of the refrigerator will

increase. Remember to turn it off when

you don’t need it and return the freezer

to your original temperature setting. If you

need to freeze a large amount of food,

activate the Power Freeze function at least

24 hours before you put the food into the

freezer.

( 2 )

Alarm/

Filter

Reset

(3sec)

The Alarm button serves two purposes:

- To turn the door open alarm on and off

- To reset the water filter life indicator.

1) Door Alarm Function

If the door alarm is set to On, an alarm

beeps if any refrigerator door is left open

for more than three minutes. The beeping

stops when you close the door. The door

alarm function is pre-set to On in the

factory. You can turn it off by pressing

and then releasing the Alarm button. You

can turn it back on in the same fashion.

The icon lights up when the function is on.

When the Door Alarm function is on and

the alarm sound is triggered, the Door

Alarm Icon will blink while the alarm

sounds.

2) Water Filter Life Indicator Function

After you replace the water filter, touch

and hold this button for 3 seconds to

reset the water filter life indicator. When

you reset the water filter life indicator,

the Filter icon on the panel turns Off. The

Filter icon will turn red to let you know it

is time to change the water filter after six

months (about 300 gallons). Some areas

have large amounts of lime in their water,

which causes the water filter to clog more

quickly. If this is the case in your area,

you will have to change the filter more

frequently than every six months.

( 3 )

Energy

Saver

Touching this button turns Energy Saver

mode on and off. When you turn Energy

Saver on, the Energy Saver icon lights.

Turn Energy Saver off and the icon goes

off. The Energy Saver function’s factory

setting is “ON”. If condensation or water

drops appear on the doors, turn the

Energy Saver mode off.

RF30KMED_DA68-02894B-01_EN.indd 17 2016-03-30  12:56:05

18 English

( 4 )

Fridge/

Power

Cool

(3sec)

The Fridge button serves two purposes:

- To set the Fridge to your desired

temperature.

- To turn the Power Cool function on

and off.

1) To set the Fridge temperature,

press the Fridge button. You can set the

temperature between 44 °F (7 °C) and

34°F (1 °C).

2) Power Cool function

Touch and hold this button for 3 seconds

to decrease the time needed to cool

products in the Refrigerator. It can be

helpful if you need to quickly cool easily

spoiled items or if the temperature in

the fridge has warmed dramatically (for

example, if the door was left open).

( 5 )

Lighting/

ºC ↔ ºF

(3sec)

The Lighting button serves two purposes:

- To turn the dispenser light on and off

- To switch the temperature units

between ºC and ºF

1) Light Function

Touching the Lighting button turns on the

Dispenser LED lamp in continuous mode

so that it stays on continuously.

The button also lights up. If you want the

Dispenser lamp to come on only when

some one uses the dispenser, press the

Lighting button to turn the continuous

mode off.

2) To switch the temperature units

between ºC and ºF

Touch and hold this button for 3 seconds

to select the temperature display you

want.

Each time you press and hold the button,

the ºC and ºF temperature modes

alternate and the ºC or ºF icon lights up,

indicating your selection.

( 6 )

Ice Maker

Off/

Control

Lock

(3sec)

The Ice Maker Off button serves two

purposes:

- To turn the Ice maker on and off

- To turn the Control Lock Function on

and off.

1) Ice Off Function

If you don’t want to make more ice, press

the Ice Maker Off button.

2) Control Lock Function

Touch and hold this button for 3 seconds

to lock the display, the Flex Zone panel,

and the dispenser buttons so the buttons

can not be used.

When Control Lock is on, the refrigerator

does not dispense ice or water, even if the

Dispenser Lever is pressed.

The Control Lock icon lights up to

indicate you’ve activated the Control Lock

function. Press 3 seconds to unlock.

(7)

Water

Touch this button to dispense water. This

mode can not be used with the Ice Type

mode simultaneously.

Water mode shuts off when you touch the

Cubed/Crushed Ice button.

( 8 )

Filter

Water filter usage

This icon lights up when you need

to change the filter, usually after the

refrigerator has dispensed about 300

gallons of water (after about 6 months).

The icon will blink red for several seconds

when you open or close the door.

After you install the new water filter, reset

the filter indicator by touching and holding

the Hold 3 sec for Filter Reset button for

3 seconds.

- If water is not dispensing or

dispensing slowly, you need to

replace the water filter because

the water filter is clogged.

- Some areas have large amounts

of lime in their water, which

causes the water filter to clog

more quickly.

( 9 )

Ice Type

Touch this button to select your desired

ice type. Cubed and crushed ice modes

alternate when you press the button. This

mode can not be used with the Water

mode simultaneously.

Cubed

Crushed

RF30KMED_DA68-02894B-01_EN.indd 18 2016-03-30  12:56:06

English 19

02 OPERATING

To save electricity, the Panel Display turns off

automatically under the following conditions:

When no button has been pressed, when

no doors are open, or when no Dispenser

Lever has been pushed. However, the icon

indicating your selection of cubed or crushed

ice, or water remains active. When you press

a button, open a door, or push a Dispenser

Lever, the Panel Display will turn on again.

Except for the Energy Saver, Water, and

Cubed/Crushed Ice buttons, all function

buttons will become operational after you

remove your ﬁnger from the button you are

currently pressing.

( 10 )

Ice Maker

Off

If you don’t want to make more ice, touch

the Ice Maker Off button.

The icon will light up and the Ice-Maker

stops making ice.

We recommend you stop ice

making if the following occur:

- There is enough ice in the ice

bucket.

- You want to save water and

energy.

- Water is not being supplied to

the refrigerator.

If the ice maker function is ON, and

the water line is not connected,

there will be a water valve noise

from the back of the unit. If this

occurs, press the Ice Maker Off

(Control Lock(3sec)) button for less

than 3 seconds until the Ice Off

Indicator ( ) illuminates.

Cooling

Off Mode

Cooling Off mode (also called Shop

mode), is designed for use by retailers

when they are displaying refrigerators on

the shop floor.

In Cooling Off mode, the refrigerator’s

fan motor and lights work normally, but

the compressors do not run, and the

refrigerator and freezer do not get cold.

To start Cooling Off mode, touch and hold

the Freezer, Fridge and Alarm buttons for

5 seconds during normal operation.

The refrigerator chime sounds and the

temperature display flashes OFF.

To cancel Cooling Off mode, touch

and hold the Freezer, Fridge and Alarm

buttons again for 5 seconds.

CHANGING THE WATER

FILTER

To reduce the risk water damage to your

property DO NOT use generic brands of

water filters in your SAMSUNG

Refrigerator.

USE ONLY SAMSUNG BRAND

WATER FILTERS. SAMSUNG is not

legally responsible for any damage,

including, but not limited to, property

damage caused by water leakage

from the use of a generic water ﬁlter. SAMSUNG

Refrigerators are designed to work ONLY WITH

SAMSUNG Water Filters.

The Filter light turns red to let you know when it is

time to change your water ﬁlter cartridge.

To give you time to get a new ﬁlter, the red light

comes on just before the capacity of the current

ﬁlter runs out. Changing the ﬁlter on time provides

you with the freshest, cleanest water from your

refrigerator.

To change the water filter, follow these steps:

1. Shut off the water supply. Then, turn the water

filter (1) about 1/4 turn, counter-clockwise.

2

1

2. Pull the water filter (1) from the case filter (2).

• To change the water filter more easily,

shut off the water supply valve.

• Sometimes, it is hard to disassemble the water

filter because impurities in the water cause it

to stick. If you are having difficulties, grip the

water filter firmly and pull it hard.

• When you pull the water filter, a little water

can leak from the opening. This is normal.

To minimize the water leaks, keep the filter

cartridge horizontal when you pull it.

• To prevent overflow,

empty the water filter

tray (3) and dry

around the filter case

(2).

WARNING

(Red)

3

2

RF30KMED_DA68-02894B-01_EN.indd 19 2016-03-30  12:56:17

20 English

3. Insert the new filter into the filter case (4).

4. Push the filter, and then turn it clockwise until

it locks.

• If you have trouble inserting the water

filter because of high water pressure,

shut off the water supply valve.

• The locked symbol should be lined up

with the indicator line.

4

5. Touch the “Alarm/hold

3 sec for Filter Reset”

button (

(Filter Reset)

) for

about 3 seconds to reset

the water filter. The color

of the indicator (

)

changes from red to off.

6. If you turned off the water supply, turn it back

on.

For a replacement water filter, you can visit

your local home Improvement center or

contact the Samsung Parts distributor.

To order more water filter cartridges,

contact your authorized Samsung dealer.

Be sure the replacement water filter has

the SAMSUNG logo on the box and on the

water filter.

Removing any residual matter inside

the water supply line after installing

the water ﬁlter.

1. Turn ON the main water supply and supply

water from water supply line.

2. Run water through the

dispenser until the water

runs clear (approx. 6 to 7

minutes). This will clean

the water supply system

and remove air from the

lines.

3. Additional flushing may be required in some

households.

4. Open the Refrigerator door and make sure

there are no water leaks coming from the

water filter.

Be sure to flush the dispenser thoroughly,

otherwise water may drip from the

dispenser.

This means that there is still air in the line.

Reverse Osmosis Water Supply

IMPORTANT:

The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet

valve of the refrigerator needs to be between 35

and 120 psi (241 and 827 kPa).

If a reverse osmosis water ﬁltration system is

connected to your cold water supply, the water

pressure to the reverse osmosis system needs to

be a minimum of 40 to 60 psi (276 to 414 kPa.) If

the water pressure to the reverse osmosis system

is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the

reverse osmosis system is blocked. Replace

the filter if necessary.

• Allow the storage tank on the reverse osmosis

system to refill after heavy usage.

• If your refrigerator has a water filter, it may

further reduce the water pressure when used

in conjunction with a reverse osmosis system.

Remove the water filter.

If you have questions about your water pressure,

call a licensed, qualified plumber.

RF30KMED_DA68-02894B-01_EN.indd 20 2016-03-30  12:56:17

La page charge ...

Samsung 1011516 Manuel utilisateur

Ce manuel convient également à

Samsung 1011516 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents