Brandt LVC144IB-01 Le manuel du propriétaire

LVC144IW

LVC144IB

LVC144IX

4

Press the program button for more than 3 seconds to cancel the running program.

Refer to the section entitled "Preparing and loading dishes".

Close the door, press the program button until the selected program lights up.

(see the section entitled "Operation instruction")

When the working cycle has finished, then stop. Turn off the appliance using On/Off button.

Scrap off any large amount of leftover food.

Soften remnants of burned food in pans, then load the baskets.

Refer to the dishwasher loading instruction.

5

(Follow the user instructions!)

Open the flap(marked with A), fill in the main wash detergent , and then close the flap;

Pre wash detergent drop into the tank directly;

Refill the rinse aid through the hole below the cap(marked with B)

If you need .

A

B

3.Operation Instruction3.Operation Instruction

before using it for the first time.

To get the best performance from your dishwasher, read all operating instructions

IMPORTANTIMPORTANT

Control PanelControl Panel

Start /Pause button: To start the selected

washing program or pause the washing program

when the machine is working.

On/Off Button: To turn on/off the power supply.

Delay Button : Press the button to delay cycle start time.

Program Button : Press the button to select

appropriate Program.

Alt Button: Dual zone wash function, press the

button to select either upper basket or lower basket

loaded, and the response indicator .

1133

66

447755

22

Language Button: Press the button to select

the appropriate language.

Display screen: to show the remaining time

and the state(running state, delay time etc )

Program indicators:

Rinse Aid indicator:

Indicates when the dispenser needs to be refilled.

Child lock indicator:

Add salt indicator:

Indicates when the dispenser needs to be refilled.

Delay hours indicator:

Language indicator:

Delay time ,remaining time,or error codes indicator:

Alt functions indicator:

11

22

33

44

55

66

77

Child lock button: press the two buttons for 3 seconds

simultaneously to lock the program or unlock.

88

666

• Manual pre-rinsing of tableware items leads to increased water and energy consumption and is not recommended

• Washing tableware in a household dishwasher usually consumes less energy and water in the use phase than hand

dishwashing when the household dishwasher is used according to the manufacturer’s instructions.

Adjusting Salt Consumption

The dishwasher is designed to allow for adjustment in the amount of salt consumed based on the hardness of

the water used. This is intended to optimise and customise the level o f salt consumption.

WATER SOFTENER

The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will

form on the dishes and utensils.

The appliance is equipped with a special softener that uses a salt container specifically designed to eliminate

lime and minerals from the water.

Contact your local water board for information on the hardness of your water supply.

NOTE:NOTE:

If your model does not have any water softener, you may skip this section.

Clark: British degree

fH: French degree

dH: German degree

Note:1Note:1 dH=1.25 Clarke=1.78 fH=0.178mmol/l

1

Note:2Note:2

The manufactory setting: H3 (EN 50242)

dH

mmol/l

0~90~5 0~0.94 H1 0

10-20

6-11

1.0-2.0 H2 9

21-30

12-17 2.1-3.0

H3

12

H4 20

fH

0~6

7-14

15-21

Clarke

WATER HARDNESS

Selector Position Salt c onsumption

(gram/cycle)

18-22 31-40 22-28 3.1-4.0

41-60

23-34 4.1-6.0 H5 30

H6 60

29-42

35-55 61-98 43-69 6.1-9.8

1. Switch on the appliance;

2. Press the Program button for more than 5 seconds to start the water softener set

model within 60seconds after the appliance was switched on;

3. Press the Program button to select the proper set according to your local

environment, the sets will change in the following

sequence: H1->H2->H3->H4->H5->H6

4. Press the On/Off button to end the set up model.

Please follow the steps below for adjustment in salt consumption.

a detrimental or

pour

Adjust ing t he rinse aid r eservoir

To achieve a better drying performance with limited rinse aid, the dishwasher is

designed to adjust the consumption by user. Follow the below steps.

Open the door and switch on the appliance.

Within 60 seconds after step 1, press the Program button more than 5 seconds,

and then press the Delay button to enter the set model, the rinse aid indication

Press the Program button to select the proper set according to your using habits,

the sets will change in the following sequence: D1->D2->D3->D4->D5->D1.

The higher the number, the more rinse aid the dishwasher uses.

Without operation in 5 seconds or press the Power button to complete the setup

and exit the setup mode.

Close the cap after all.

Remove the rinse reservoir cap by

lifting up the handle .

Pour the rinse aid into the dispenser,

being careful not to overfill.

blinks as 1Hz frequency.

Filling The Detergent Dispenser



Please choose an open way according

to the actual situationC

1 Open the cap by sliding the release

catch.

1 Open the cap by pressing down the

release catch.

Add detergent into the larger cavity

(A) for the main wash cycle .

For better cleaning result, especially if

you have very dirt items, pour a small

amount of detergent onto the door.

The additional detergent will activate

during the pre-wash phase.

Close the flap by sliding it to the

front and then pressing it down.

"







3



Be aware that depending on the soiling of water, setting may be different.

Please observe the manufacturer's recommendations on the detergent packaging.



Based on their chemical composition, detergents can be split in two basic types:

Detergent tablets of different brands dissolve at different speeds. For this reason some

detergent tablets cannot dissolve and develop their full cleaning power during short

programs. Therefore please use long programs when using detergent tablets, to

ensure the complete removal of detergent residuals.

The dispenser must be refilled before the start of each wash cycle following the instructions

provided in the wash cycle table . Your dishwasher uses less detergent and rinse aid than

Conventional dishwasher. Generally, only one tablespoon of detergent is needed for

a normal wash load. More heavily soiled items need more detergent. Always add the

detergent just before starting the dishwasher, otherwise it could get damp and will not

dissolve properly.

Concentrated Detergent

Detergent Tablets

Detergent Dispenser

conventional, alkaline detergents with caustic components

low alkaline concentrated detergents with natural enzymes

Normally new pulverised detergent is without phosphate. Thus the water softener function of

phosphate is not given. In this case we recommend to fill salt in the salt container even when

the hardness of water is only 6 °dH. If detergents without phosphate are used in the case of hard water

often white spots appear on dishes and glasses. In this case please add more detergent to reach

better results. Detergents without chlorine do only bleach a little. Strong and coloured spots will not

be removed completely. In this case please choose a program with a higher temperature.

Detergents

There are 3 sorts of detergents

1.With phosphate and with chlorine

2.With phosphate and without chlorine

3.Without phosphate and without chlorine

Detergents with its chemical ingredients are necessary to remove dirt, crush dirt and transport it out of the dishwasher.

Most of the commercial quality detergents are suitable for this purpose.

D. Function of Detergent

Proper Use of Detergent

Use only detergent specifically made for the use in dishwashers. Keep your detergent fresh and dry.

Don't put powdered detergent into the dispenser until you're ready to wash dishes.

Attention!

Lift the basket for higher position Lift the handle to lower the basket

For better stacking of pots and pans,the spikes can be folded

down as shown on the picture below.

13

To make room for taller items in the upper basket, raise the

You can then lean the tall glasses against

required for use.

cup rack upwards.

it. You can also remove it when it is not

6.Starting a washing program6.Starting a washing program

NOTE:NOTE:

*EN 5 0242 : This programme is the test cycle. The information for comparability test

in accordance with EN 50242, as follows:

Capacity: 14 setting

Position Upper basket: upper wheels on rails

Rinse aid setting: 5

Pl:0.49w; Po:0.45w.

Wash Cycle TableWash Cycle Table

NOTE:NOTE:

Means: Rinse-aid dispenser needs to be filled.

( )

Detergent

pre/main

Detergent

pre/main

Cycle Selection

Information

Cycle Selection

Information

ECO

ProgramProgram

Intensive

(*EN 5 0 242)

Running

time(min)

Running

time(min) Water

(L)

Water

(L)

Energy

(Kwh)

Energy

(Kwh)

Rinse

Aid

Rinse

Aid

(1 or 2 pieces)

5/30g

Rapid

Pre-wash (50 )

Wash (65 )

Rinse

Rinse(60 )

Drying

Pre-wash(45 )

Wash (55 )

Rinse

Rinse (55 )

Drying

Pre-wash

Wash (50 )

Rinse(50 )

Drying

Wash (45 )

Rinse (45 )

175

0.765

1.5

0.82

16.6

13.6

11.2

Description

of Cycle

Description

of Cycle

60 min

Pre-wash(30 )

Wash(55 )

Rinse (50 )

Drying

60 15

1.05

5/30g

20g

Soak

Pre-wash

15 4.1

Glass

5/30g

Rinse(50 )

Drying

120

0.95 13.5

Auto

Auto sensing wash, lightly,

normally or heavily soiled

crockery, with or with out

dried-on food

Pre-wash(45 )

Autowash

(55-65 )

Rinse

Rinse(50-55 )

Drying

5/30g

0.85~1.55

To rinse dishes that you plan

to wash later that day

For normally soiled loads,

such as pots, plates,glasses

and lightly soiled pans.

For heaviest soiled crockery,

and normally soiled pots

pans dishes etc with dried

on soiling.

For lightly soiled loads that

do not need excellent drying

efficiency.

For lightly soiled crockery

and glass.

A shorter wash for lightly

soiled loads that do not

need drying.

This is standard programme,

it is suitable to clean normally

soiled tableware and it is the

most efficient programme in

terms of its combined energy

and water consumption for

that type of tableware.

14-1

S

ECO

(1 or 2 pieces)

(1 piece)

30

Universal

Values other than the ECO program are purely indicative.

Wash(50 )

Wash(60 )

Rinse(50 )

80-150

205

198

8.5~18

0.98

9.8

Turning On the ApplianceTurning On the Appliance

Starting a cycle wash

Draw out the lower and upper basket, load the dishes and push them back.

It is recommended to load the lower basket first, then the upper one (see the section entitled

Pour in the detergent (see the

Insert the plug into the socket. The power supply is 220-240 VAC /50 HZ, the specification

of the socket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.

Close the door, press the ON/OFF Button, and the display will turn on.

Press the program Button , the wash program will be changed as follows direction:

ECO->Glass->60min->Rapid->Soak->Auto->Intensive->Universal

If a program is selected, the response light will turn on. Then press the Start/Pause button and the dishwasher

will start its wash cycle.

1

2

3

4

5

NOTE:NOTE:

*EN : This programme is the test cycle. The information for comparability test

in accordance with EN , as follows:

Capacity: 14 setting

Position Upper basket: upper wheels on rails

Rinse aid setting: 5

Pl:0.49w; Po:0.45w.

Wash Cycle TableWash Cycle Table

NOTE:NOTE:

Means: Rinse-aid dispenser needs to be filled.

( )

Detergent

pre/main

Detergent

pre/main

Cycle Selection

Information

Cycle Selection

Information

ECO

ProgramProgram

Intensive

(*EN 6 0 436)

Running

time(min)

Running

time(min) Water

(L)

Water

(L)

Energy

(Kwh)

Energy

(Kwh)

Rinse

Aid

Rinse

Aid

(1 or 2 pieces)

Rapid

Pre-wash (50 )

Wash (65 )

Rinse

Rinse(60 )

Drying

Pre-wash(45 )

Wash (55 )

Rinse

Rinse (55 )

Drying

Pre-wash

Wash (50 )

Rinse(50 )

Drying

Wash (45 )

Rinse (45 )

175

0.747

1.5

0.75

16.6

13.6

11.2

Description

of Cycle

Description

of Cycle

60 min

Pre-wash(30 )

Wash(55 )

Rinse (50 )

Drying

60 15

1.05

20g

Soak

Pre-wash

15 4.1

Glass

Rinse(50 )

Drying

120

0.95 13.5

Auto

Auto sensing wash, lightly,

normally or heavily soiled

crockery, with or with out

dried-on food

Pre-wash(45 )

Autowash

(55-65 )

Rinse

Rinse(50-55 )

Drying

0.85~1.55

To rinse dishes that you plan

to wash later that day

For normally soiled loads,

such as pots, plates,glasses

and lightly soiled pans.

For heaviest soiled crockery,

and normally soiled pots

pans dishes etc with dried

on soiling.

For lightly soiled loads that

do not need excellent drying

efficiency.

For lightly soiled crockery

and glass.

A shorter wash for lightly

soiled loads that do not

need drying.

This is standard programme,

it is suitable to clean normally

soiled tableware and it is the

most efficient programme in

terms of its combined energy

and water consumption for

that type of tableware.

14-2

->ECO

Preparing and loading dishes Prior to first time use

S

->ECO

ECO

(1 or 2 pieces)

30

))

Universal

Values other than the ECO program are purely indicative.

Wash(50 )

Wash(60 )

Rinse(50 )

80-150

205

198

8.5~18

0.98

9.8

60436

4/18g

(1 or 2 pieces)

4/18g

detergent

may have already been released, and the appliance may have already drained the wash water.

then you can

change the program to the desired cycle setting(See the section entitled"Start a washing program...").

After washing, the door will open automatically to achieve better drying effect.

The dishwasher door must not be blocked when set to open automatically.

This can disrupt door lock functionality.

NOTE:

Auto Open Door

to be drained.

Micro-filterMicro-filter

La page charge ...

Brandt LVC144IB-01 Le manuel du propriétaire

Ce manuel convient également à

Brandt LVC144IB-01 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents