Tetra Snap DS Cabinet Signs Guide d'installation

Tetra
Marque
Tetra
Modèle
Snap DS Cabinet Signs
Taper
Guide d'installation
Installation Guide
SIGN271 | A-1025384
PowerStrip Snap DS
LED Lighting System
GEDS71-3, GEDS65-3, GEDS57-3,
GEDS50-3, GEDS41-3, GEDS32-3
RETROFIT SIGN CONVERSION LED KIT FOR USE ONLY
IN ACCORDANCE WITH KIT INSTRUCTIONS.
KIT IS COMPLETE ONLY WHEN ALL PARTS REQUIRED
BY THE INSTRUCTIONS ARE PRESENT.
TROUSSE DE CONVERSION À DEL POUR LA
MODERNISATION DES ENSEIGNES
À UTILISER CONFORMÉMENT AU GUIDE D’INSTALLATION.
Prepare Electrical Wiring Save These Instructions
Use only in the manner intended by the
manufacturer. If you have any questions, contact the
manufacturer.
2424
Volt
For the latest North American install guides for your product go to: https://products.LED.com/led-signage-lighting
For the latest European install guides for your product go to: https://products.LED.com/eu/led-signage-lighting
FOR UL ONLY
BG Българската версия на инструкциите за инсталаця и
информация за безопасност могат да бъдат намерени
на следния адрес: https://products.LED.com/eu
CS Návod k montáží a bezpečnostní informace v češtině
najdete zde: https://products.LED.com/eu
DA Den danske version af installationsvejledningen og
sikkerhedsoplysninger kan findes på følgende placering:
https://products.LED.com/eu
DE Die deutsche Version der Installationsanleitung und
Sicherheitsinformationen finden Sie in folgendem Verzeic:
https://products.LED.com/eu
EL Μπορείτε να βρείτε την ελληνική εκδχή των οδηγιών
νγκατάστασης και των πληροφοριών ασφάλειας στην
εξής τοποθεσία: https://products.LED.com/eu
ES La versión española de las instrucciones de instalación y
la información sobre seguridad puede encontrarse en la
siguiente ubicación: https://products.LED.com/eu
ET Eestikeelse paigaldusjuhendi ja ohutusnñuded leiate
aadressilt: https://products.LED.com/eu
FI Asennusohjeiden ja turvallisuustietojen suomenkielinen
versio löytyy seuraavasta paikasta: https://products.LED.
com/eu
FR La version française des instructions d’installations
et information de sécurité est disponible à l’adresse
suivante: https://products.LED.com/eu
HR Hrvatska verzija priručnika za ugradnju i sigurnosnih
informacija nalazi se na sljedečoj lokaciji: https://products.
LED.com/eu
HU A telepítési útmutató és a biztnosági információk magyar
nyelvű változata az alábbi címen található: https://
products.LED.com/eu
IT La versione italiana del manuale di installazione e
sicurezza può essere reperita nella seguente sezione:
https://products.LED.com/eu
LT Lietuvišką diegimo instrukcijos ir saugos informacijos
versiją galima rasti šioje vietoje: https://products.LED.
com/eu
LV Uzstādīšanas instrukciju un drošības informāciju latviešu
valodā var atrast šeit: https://products.LED.com/eu
NL De Nederlandse versie van de installatie-instructies en
veiligheidsinformatie kan op de volgende locatie worden
gevonden: https://products.LED.com/eu
PL Polską wersję instrukcji instalacji oraz informacje
dotyczące bezpieczeństwa można znaleźć w następującej
lokalizacji: https://products.LED.com/eu
PT A versão em Português das instruções de instalação e
das informações de segurança pode ser encontrada na
seguinte localização: https://products.LED.com/eu
RO Versiunea în limba română a instrucţiunilor de instalare
şi a informaţiilor de siguranţă pot fi găsite la: https://
products.LED.com/eu
SV Ni hittar den svenska versionen av
installationsanvisningarna och säkerhetsinformationen på
följande plats: https://products.LED.com/eu
SL Previdnostna opozorila in varnostne informacije so na
zadnji strani vodnika za namestitev. Pred začetkom
namestitve izdelka jih skrbno preberite: https://products.
LED.com/eu
SK Slovenskú verziu montažnej príručky a bezpečnostnŷch
instrukcií nájdete na nasledujúcej lokalite: https://
products.LED.com/eu
Electrical Requirements
• Limited to use in dry and damp locations.
• The grounding and bonding of the LED Driver shall be
done in accordance with National Electric Code (NEC)
Article 600.
• Follow all National Electric Codes (NEC) and local codes.
• These products are only suitable for connection to a
circuit from a Class 2 power source. These products
have not been evaluated for use when connected to a
power source that does not comply with Class 2 voltage
and energy limited supplies.
EN
BEFORE YOU BEGIN
Read these instructions completely and carefully.
Tetra® PowerStrip Snap DS Installation Guide
2
CAUTION / ATTENTION
RISK OF INJURY
• While performing installations described, gloves, safety glasses or
goggles should be worn.
RISQUE DE BLESSURE
• Lors de l’exécution des installations décrites, des gants, des lunettes de
sécurité ou des lunettes de protection doivent être portées.
WARNING / AVERTISSEMENT
RISK OF ELECTRIC SHOCK
∙ Turn power off before inspection, installation or removal.
∙ Properly ground power supply enclosure.
RISK OF FIRE
∙ Use only suitably approved wire for input/output connections.
Minimum size 18 AWG (0.82mm2)
∙ Follow all local codes.
∙ Not to be submerged or used in a marine environment.
RISQUES DE DÉCHARGES ÉLECTRIQUES
∙ Coupez l’alimentation avant l’inspection, l’installation ou le déplacement.
∙ Assurez-vous de correctement mettre à terre l’alimentation électrique.
RISQUES D’INCENDIE
∙ N’utilisez que des fils approuvés par UL pour les entrées/sorties de
connexion. Taille minimum 18 AWG (0.82mm2)
∙ Respectez tous les codes locaux.
∙ Ne pas submerger ou installer dans un environnement marin.
UL WARNING / AVERTISSEMENT UL
RISK OF FIRE OR ELECTRIC SHOCK
∙ LED Retrofit Kit installation requires knowledge of sign electrical
systems. If not qualified, do not attempt installation. Contact a
qualified electrician.
∙ Install this kit only in host signs that have been identified in the
installation instructions and where the input rating of the retrofit kit does
not exceed the input rating of the sign.
∙ Installation of this LED retrofit kit may involve drilling or punching of
holes into the structure of the sign. Check for enclosed wiring and
components to avoid damage to wiring and electrical parts.
∙ Do not make or alter any open holes in an enclosure of wiring or
electrical components during kit installation.
RISQUE D’INCENDIE OU DE CHOC ÉLECTRIQUE
∙ L’installation de l’équipement de remplacement DEL exige Ia
connaissance des systèmes électriques pour enseignes. Si non qualifié,
ne tentez pas d’installation. Veuillez contacter un électricien qualifié.
∙ Risque d’incendie ou de choc électrique. Installez cet ensemble
seulement dans des enseignes hôtes qui ont été identifiés dans les
instructions d’installation et dont la capacité d’entrée de l’ensemble ne
dépasse pas la capacité d’entrée de l’enseigne.
∙ L’installation de cet équipement de remplacement DEL peut impliquer le
perçage ou le poinçonnage de trous dans la structure du panneau Vérifiez
le câblage et les composants inclus pour éviter d’endommager le câblage et
les composants électriques.
∙ Ne pas faire ou modifier les trous ouverts dans une enceinte de câblage
ou de composants électriques pendant l’installation de cet équipement
de remplacement DEL.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This Class [A] RFLD complies with the Canadian standard ICES-005. Ce DEFR de la classe [A] est conforme à la NMB-005 du Canada.
This product is intended solely for sign use only. Not intended for general lighting applications.
If you have any questions about these instructions or your specific application, please contact support at [email protected].
Conforms to the following standards: IP66.
LED modules are not suitable for prolonged submersion or direct exposure to water and must be protected from the weather.
Acceptable for use in dry and damp locations
The suitability of rain enclosure shall be determined if intended for wet location.
Electrical products must not be thrown out with domestic waste. They must be taken to a communal collecting point for environmentally friendly
disposal in accordance with local regulations. Contact your local authorities or stockist for advice on recycling. The packaging material is recyclable.
Dispose of the packaging in an environmentally friendly manner and make it available for the recyclable material collection-service.
Tetra® PowerStrip Snap DS Installation Guide
3
Components
Electrical grade RTV silicone.
Example electrical grade RTV silicones include:
• Momentive RTV 6700 Series Silicone Rubber Adhesive Sealant
• Momentive White Blanc RTV 162 Silicone Rubber Adhesive
Sealant-Electrical Grade
• Dow Corning 3140 - Non-Corrosive Flowable (clear)
• Dow Corning 3145 - Non-Corrosive Nonflowable (clear or gray)
• Dow Corning RTV 748 Non-Corrosive Sealant-White
UL certified 18 AWG (0.82 mm2) supply wire
UL certified 22-14 AWG (0.33-2.08 mm2) wire
connectors or 18-14 AWG (0.82-2.08 mm2) inline/
IDC connectors
#6 and #8 x 0.50 inch (M3 and M4 x 13mm)
self-tapping screws or 1/8” rivets
Wire end caps
24 VDC Power Supply
Tetra® PowerStrip Snap DS
Tetra® Snap 8ft. Rail (GEDSRL08-3)
Tetra® Snap Socket Endcap (GEDSSE-3)
Tetra® Snap Frame Endcap (GEDSFE-3)
Tetra® Snap Interconnector (GEDSIC-3)
Tetra® Snap T-Connector (GEDSTC-3)
TC Measure Point
Optional
12
12
11
11
10
10
9
9
8
8
7
7
1
12 3 4 5 6
2
3
4
5
6
Tetra® PowerStrip Snap DS Installation Guide
4
Measure and cut Tetra® Snap Rail to appropriate
length to fit into sign. For retrofitting a sign, see
page 6.
Evenly space modules across the Tetra® Snap
Rail. Different brightness levels can be achieved
depending on module spacing.
Installation Using Tetra® Snap Rails
Align peg on top of the light module with hole
on top of the Tetra® Snap Rail and push module
into rail until it snaps into place. For added
security, fasten module to rail with a screw.
Secure the Tetra® Snap Rail to the inside of the
box sign using the standard Tetra® Snap Frame
Endcaps or other suitable means.
Measure inside
Sign
Rail (mounted vertically)
SNAP!
More bright Less bright
Mount endcap
to sign structure
1
3
2
4
Insert a small screwdriver between the rail and
end of the module as shown.
Removing Modules
Push up on the module until the first leg is out
of the rail. Pull the module out of the rail.
1 2
Tetra® PowerStrip Snap DS Installation Guide
5
Use a Tetra® Snap Interconnecter
to join two rails and create longer
runs.
NOTE: Runs must be secured with
screws to supporting structure
at intervals no greater than
8 feet (2.43 m).
Use a Tetra® Snap T-Connector to join
rails perpendicular to each other.
Use #6 or #8 screw to attach
T-Connector to side of rail.
NOTE: T-Connector must be secured
with screws to the mounting rail.
Using Tetra® Snap Interconnectors
Alternative Mounting
Using Tetra® Snap T-Connectors
The modules may be attached to any
structural member of the sign using one
#6 or M3 screw or 1/8” rivet. Ensure the
module’s lip is tight against rail.
NOTE: Modules may be damaged by
improperly sized screws or over-torquing.
Screw must be at least 0.75 inches long.
Mount modules
to sign structure.
2 fasteners may
be used for
added security.
T-Connector
#6 or #8
screws
Interconnector
Support
structure
Installation Options
Tetra® PowerStrip Snap DS Installation Guide
6
When retrofitting a sign, ensure the
rail is cut to the appropriate length to
properly seat in the lamp socket, and
use Tetra® Snap Socket Endcaps to
secure rails to existing lamp sockets.
NOTE: When utilized, ensure the rail
is properly seated in the lamp sockets.
For horizontal installations greater than
5 ft. in length, the rail assembly should
be centrally supported.
Tetra Snap
Socket Endcap
Lamp
socket
#8 screw
Nominal T12
Tube Length
Nominal Rail
Cut Length
1.5 ft. 15” (381.5mm)
2 ft. 21” (533.1mm)
2.5 ft. 27” (685.8mm)
3 ft. 33” (837.9mm)
3.5 ft. 39” (990.6mm)
4 ft. 45” (1142.7mm)
5 ft. 57” (1447.5mm)
5.33 ft. 61” (1549.5mm)
6 ft. 69” (1752.3mm)
7 ft. 81” (2057.1mm)
8 ft. 93” (2361.9mm)
Tetra® Snap Nominal LFL
Rail Length Requirements
1. (Existing Signs Only) Prior to installation, survey the site for information regarding power and accessibility inside
and outside the building. Ensure that the branch circuit supplying the existing transformer or ballast will be within
the voltage ratings of the new LED power supply, and have a current rating not exceeding 20A, or that permitted by
applicable local, state, or country electrical codes (whichever is less).
2. (Existing Signs Only) Remove the existing lighting equipment to be replaced, such as neon tubing or fluorescent
tubes; and associated transformers and ballasts. Care should be taken not to break the existing neon or fluorescent
tubes. NOTE: Follow all federal and local regulations when disposing of neon tubing, fluorescent tubes, transformers
and ballasts.
3. (Existing Signs Only) If removal of the existing lighting equipment eliminates the disconnect switch, as required by
applicable local, state, or country electrical codes; a new disconnect switch must be installed.
4. (Existing Signs Only) Repair and seal any unused openings in the electrical enclosure. Openings greater than
12.7-mm (1/2-in) diameter require a metal patch secured by screws or rivets and caulked with non-hardening caulk.
Smaller openings may be sealed with non-hardening caulk.
5. Using the layout guidelines above, determine required number of LED modules required to illuminate the sign.
6. A 24VDC Class 2 Power Supply, as listed below, must be used with this retrofit kit. Using the Maximum Loading chart
below, determine the number of Power Supplies required to power the number of LED modules required to illuminate
the sign, so as not to overload the Power Supply chosen.
7. Follow the instructions above to properly mount the LED modules.
8. Connect the DC output of the power supply to the LED modules using the Electrical Connections instructions below.
9. Connect the power unit to the supply in accordance with the applicable local, state, and country electrical codes, and
the instructions found in the power supply installation guide.
10. If required, the disconnect switch shall be installed by qualified personnel, in accordance with applicable local, state, and
country electrical codes.
Retrofit Instructions
FOR UL ONLY
Using Tetra® Snap Socket Endcap
Tetra® PowerStrip Snap DS Installation Guide
7
Connect output side of
power supply to first
module. Connect the
red stripe wire (+) of the
LED system to the red wire
(+) of the power supply.
Connect the white wire (-) of
the LED system to the black
or blue wire (-) of the power
supply. Connect AC line to
input side of power supply.
Connect modules using twist-on
wire connectors or in-line (IDC)
connectors. Join white wires
together and red striped wires
together.
Cap all exposed wires with
appropriate end caps or apply
electric grade (non-corrosive) silicone
for additional weather protection.
NOTES:
• Exceeding maximum load will cause the power supply to shut down. If overload occurs, remove excess load, recycle the
input power to restart the power supply.
• All electrical connections should be suitably protected from mechanical damage and the environment. Seal all connections
in locations that may be exposed to water with electrical grade RTV silicone. See page 3 for recommended silicones.
• Must be used with Class 2 24 Volt Power Supplies.
• Additional supply wire may be necessary to bridge electrical connections.
• Wire nuts should be facing up so as not to collect water.
Electrical Connections
Power
supply
First
module
Last
module
AC line
3
3
1
1
1
2
2
Dismantling
At the end of life, the contained LED light source may be cut out using suitable wire cutters, removed from the mounting surface,
then replaced per the cutting and installation instructions above, or dismantled and taken to a communal collecting point for
environmentally friendly disposal in accordance with local regulations by a professional installer.
Tetra® PowerStrip Snap DS Installation Guide
Troubleshooting
Symptom Solution
Row of modules does
not light • Check wire connections to power supply to ensure red stripe-to-red and white-to-black or blue connections.
• Check row-to-row polarity connections.
Sign does not light • Check input and output voltage and check power supply input/output connections.
• Check polarity connections.
• Ensure the overall length of the Tetra® LED System does not exceed the maximum load.
Individual modules
do not light • Remove module and replace with another working module.
Modules are dim • Ensure the overall length of the Tetra® LED system does not exceed the maximum load.
• Ensure the length and gauge of the supply wire is equal to or below the recommended remote
mounting distance.
Maximum Loading per 24V DC Power Supply
Power Supply
GEDS71-3, GEDS65-3, GEDS57-3
GEDS50-3, GEDS41-3, GEDS32-3
Rating per module 24VDC, 2.59W/module
GEPS24-25U-NA
Load shall not exceed 1.04A 8 modules
GEPS24D-60U-GLX, *GELP24-60U-GL
Load shall not exceed 2.5A 21 modules
GEPS24D-80U, GEPS24W-80
Load shall not exceed 3.3A 26 modules
GEPS24-100U-GLX, GEPS24D-100U-NA, GEPS24LT-100U-NA,
USVI-100024FBA, USVI-100024FE
Load shall not exceed 4.0A
32 modules
GEPS24-180U
Load shall not exceed 3.8A per each (of 2) output channels
29 modules per bank
58 modules per PS
GEPS24-300U-GL
Load shall not exceed 4.0A per each (of 3) output channels
32 modules per bank
96 modules per PS
GEPS24-100U-GLX2/TT, **GEPS24V50-100W
Load shall not exceed 4.0A 33 modules
GEPS24-200U-GLX2
Load shall not exceed 4.0A per each (of 2) output channels
33 modules per bank
66 modules per PS
GEPS24-300U-GLX2
Load shall not exceed 4.0A per each (of 3) output channels
33 modules per bank
99 modules per PS
Power Supply
Wattage
18 AWG/0.82 mm2
Supply Wire
16 AWG/1.31 mm2
Supply Wire
14 AWG/2.08 mm2
Supply Wire
12 AWG/3.31 mm2
Supply Wire
25W 120 ft./36.6 m – – –
60W, 80W, 100W,
180W, 200W, 300W 20 ft./6.1 m 25 ft./7.6 m 35 ft./10.6 m 40 ft./12.1 m
Maximum Remote Mounting Distance from Driver Ouput
*GELP24-60U-GL minimum load = 8 modules.
**GEPS24V50-100W minimum load = 20 modules
LED.com
© 2023 Current Lighting Solutions, LLC. All rights reserved. Information and specifications subject to change
without notice. All values are design or typical values when measured under laboratory conditions.
Page 8 of 8
(Rev 06/20/23)
SIGN271 | A-1025384
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Tetra Snap DS Cabinet Signs Guide d'installation

Tetra
Marque
Tetra
Modèle
Snap DS Cabinet Signs
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents