Dec. 2023
Phone (800) 526.2588
Fax (800) 526.2585
44 Harbor Park Drive
Port Washington, NY 11050
1600 Distribution Ct
Lithia Springs, GA 30122
1750 Archibald Avenue
Ontario, CA 91760
1
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
•
• Retain installation instructions for future maintenance reference.
All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could
result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are
damaged or missing.
Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce
produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez
contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
A
Wire Connector
Qty: 3 pcs +1 Extra
B
Mounting Screw
Qty: 1 Extra
C
INSTALLATION INSTRUCTION
WS-W65412
654-Outdoor Wall Sconce
Qty: 1 Extra
Rubber Gasket
Dec. 2023
Phone (800) 526.2588
Fax (800) 526.2585
44 Harbor Park Drive
Port Washington, NY 11050
1600 Distribution Ct
Lithia Springs, GA 30122
1750 Archibald Avenue
Ontario, CA 91760
2
INSTALLATION INSTRUCTION
WS-W65412
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig.2 Wiring
Back Plate Dimensions
654-Outdoor Wall Sconce
PREPARATION
1. Shut off the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area.
Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIFIXTURE (Fig. 1,3)
3. Loosen the mounting screw (B) and rubber gasket(C) from the xture, and
remove the mounting plate.
4. Set color temperature at this stage. The xture can switch between four
color temperatures (2700K,3000K, 3500K,4000K), which can be adjusted
to your preference using the 4CCT switch (Fig. 3) mounted in the canopy.
Note: the switch comes with a removable protective cover, Remove the
cover prior to adjusting the color temperature, Fasten the cover after
adjustment is made.
5. Secure the mounting back plate to the junction box using standard
junction box screws that comes with the junction box.
Note: (i) using any other non-original-manufacturer provided junction box
screw may result in safety issue;
(ii) The side of the mounting plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
7. Connect the driver’s input wires to junction box wires as shown in Fig. 2, make sure that all wire
connectors (A) are secured. If your outlet box has a green or bare copper ground wire, connect
the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the
mounting plate using the screw provided. After wires are connected, tuck them carefully inside
the junction box.
COMPLETING THE INSTALLATION(Fig.1)
Fig.3
4000K 3500K 3000K 2700K
Fig.1
Fixture Junction box
Junction box Screw
Wire Connector
A
Rubber Gasket
C
Mounting Screw
B
Mounting Plate
9. To prevent moisture from entering the outlet box and causing a short,
use clear caulking(i.e. indoor/outdoor silicone sealant) to outline the
outside of xture back plate where it meets the wall. Leave a space at the
and rubber gasket(C).
bottom to allow the moisture to escape (Fig. 4).
Junction Box
Caulking
Fig.4 Sealing
7 7/8〞
1 3/4〞
5 1/4〞
1 3/8〞
8. Secure the xture to the mounting plate use the mountingscrew(B)
Driver
4CCT Switch Cover
4CCT Switch
-
1
-
2
dans d''autres langues
Documents connexes
-
WAC Lighting WS-63412 Mode d'emploi
-
-
-
-
-
-
-
-
-