Bestop Sunrider for Hardtop Guide d'installation

Marque: Bestop

Modèle: Sunrider for Hardtop

Taper: Guide d'installation

Installation Instructions

Sunrider for Hardtop

Vehicle Application:

Jeep® Wrangler JL 2 Door and 4 Door 2018-current

Jeep® Gladiator 2020-current

Part Number 52454

Before you begin installing your new Sunrider for Hardtop,

please read all the instructions thoroughly, and watch the Bestop

Installation video. (See Support section on this page).

Do not rely in any way on the components of this product to protect

against injury or death in the event of an accident. Never operate the vehicle in excess of

manufacturer’s specications.

Read and follow, precisely, all installation instructions provided when installing this product.

Failure to do so may result in a poor t and could place occupants of the vehicle in a potentially

dangerous situation.

WEAR SEAT BELTS AT ALL TIMES

Safety glasses should be worn at all

times when installing this product.

WARNING

Installation Tips

Installation TimeTools

Skill Level

1 - Easy

30 minutes

Safety

Glasses

T40

Torx Driver

Support

We’re here to help! Go to:

https://www.bestop.com

and click on Need Help?

https://www.bestop.com/video-library

Torque Wrench Slotted Screw Driver

Installation Instructions

Sunrider for Hardtop

Vehicle Application:

Jeep® Wrangler JL 2 Door and 4 Door 2018-current

Jeep® Gladiator 2020-current

Part Number 52454

Installation Instructions

Supertop NX Twill

Vehicle Application:

Jeep Wrangler Unlimited

2007-current

Part Number 54823

Installation Instructions

Sunrider for Hardtop

Parts List

Vehicle Application:

Jeep® Wrangler JL 2 Door and 4 Door 2018-current

Jeep® Gladiator 2020-current

Part Number 52454

Door Rail - Passenger Side

Part #577.20

Qty. 1

Flanged Button-Head

Screw M8x20

Part #573.09

Qty. 6 Flanged Button-Head

Screw M8x80

Part #532.23

Qty. 4

Door Rail - Driver Side

Part #577.21

Qty. 1

Header / Deck Assembly

Rear Clamp

Part #573.01

Qty. 1

Sunrider Tie-Down Straps

Part #410.42

Qty. 2

Bolt Spacer Bezel

Part #574.05

Qty. 2

Screw, Binding Barrel

Part #599.01

Qty. 2

Loctite Capsule

Part #309.83

Qty. 1

Page 4

Section 1 Remove Freedom Panels & Clean Hardtop Seals

Remove both Hard Top Freedom Panels,

according to the instructions in your owner’s

manual, and conrm that all Hard Top bolts

are installed and tight.

Clean the windshield and hardtop seals with

soap, warm water and a soft cloth.

Rinse thoroughly with clean water to remove

all soap residue, and dry the seals before

installing the Sunrider for Hardtop.

Clean Seals

Check Bolts

Page 5

Section 2 Attach Cables to Door Rails

Place one (1) drop of Loctite to the Binding Screw.

Find the Cable End in the Fabric Assembly.

Attach it to the Upper Door Rail using one (1)

Binding Screw per side.

Repeat this step on the right side of the

vehicle.

Parts

Screw, Binding Barrel

Part #599.01

Qty. 2

Loctite Capsule

Part #309.83

Qty. 1

Door Rail - Passenger Side

Part #577.20

Qty. 1

Door Rail - Driver Side (Shown)

Part #577.21

Qty. 1

Slotted Screw Driver

Page 6

Note: When storing the Sunrider, It is

recommended to leave the door rails

and Deck assembled to each other.

Section 3 Attach Door Rails to Header Deck Assembly

Flanged Button-Head

Screw

Part #573.09

Qty. 2

Parts

Door Rails

Part #577.20 - Right

Part #577.21 - Left

Qty. 1 of each

Header /Deck Assembly

Qty. 1

T40

Torx Driver

Attach the Door Rails to the Deck, using two (2)

Flanged Button-Head Screws per side.

The screws go up into the Door Rails and the Deck

from underneath, and screw into the threaded inserts

installed in the Deck.

NOTE: Be sure when lining up door rails to deck assembly

that the deck assembly sits inside the door rail.

(See Detail)

Page 7

Align the holes i Door Rails with the holes in

the Jeep Sport Bar.

Attach the Door Rails (and Deck Assembly)

with two (2) Flanged Button-Head Screws.

One at the front of each Door Rail, and one

with the Bolt Spacer Bezel at the rear of the

door. Tighten to 55 in/lb (4.5 ft/lb).

The Screw at the front of the Door Rail will

screw into a threaded insert in the front

clamp from underneath.

Section 4 Attach Deck and Door Rail Assembly to Jeep Sport Bar

Parts

Flanged Button-Head

Screw M8x80

Part #532.23

Qty. 2

T40

Torx Driver

With 2 people, lift the Deck and Door

Rail Assembly with cables attached

onto the top of the Jeep.

Bolt Spacer Bezel

Part #574.05

Qty. 2

Torque Wrench

Tools

Note: To prevent over torquing, Use a

Screwdriver type Torx driver if a torque

wrench is not available.

Page 8

Section 5 Attach Rear Clamp & Close and Latch Sunrider

Parts

Attach the Rear Clamp to the deck using

two (2) Flanged Button-Head Screws.

Push down on the Deck while installing

the Screws to align the holes in the Rear

Clamp and the holes in the Deck.

Fold the Sunrider closed and secure

both latches to the vehicle’s wind-

shield header.

1 Pivot the latch handle down;

2 Engage the hook;

3 Pivot the latch handle back up.

Rear Clamp

Part #573.01

Qty. 1

Flanged Button-Head

Screw

Part #573.09

Qty. 2

T40

Torx Driver

Page 9

Section 6 Open and Secure the Sunrider (optional)

Open both latches inside the Jeep, and

fold the Sunrider back. Secure the Sunrider with the Tie Down

Straps.

Wrap each strap around both arms once

and around the upper arm once, and

secure the hook-and-loop strap.

Secure both sides of the Sunrider.

Sunrider Tie-Down Straps

Part #410.42

Qty. 2

Parts

This step is OPTIONAL and only

recommended when driving off-road

or in a situation where the Top Deck

Assembly could shift.

NOTICE

Installation Instructions

Sunrider for Hardtop

Vehicle Application:

Jeep® Wrangler JL 2 Door and 4 Door 2018-current

Jeep® Gladiator 2020-current

Part Number 52454

Care and Maintenance of your Bestop Product

Windows: Keep windows clean to avoid scratching. DO NOT use a brush on the windows! Wash with a water-soaked cloth or sponge and a mild dishwashing detergent. Bestop recommends

Bestop Vinyl Window Cleaner (part no. 11203-00), which safely cleans and protects vinyl windows and helps prevent UV damage. NEVER WIPE THE WINDOWS WHEN THEY ARE DRY. Be

careful when cleaning snow or frost from the vinyl windows since they are easily scratched and may crack at low temperatures. DO NOT roll the sides or rear window in cold weather. The

windows become stiff and will crack. Cracks caused by misuse in cold temperatures are not covered under warranty.

Zippers: Keeping zippers cleaned and lubricated with Bestop’s Zipper Cleaner (part no. 11206-00) will help prevent damage and keep the zippers in smooth

working condition. If a zipper opens behind the slider, the slider may have been spread apart. This problem can usually be repaired by

using an ordinary pair of pliers to bring the sides back into parallel. Return slider to the end of the zipper in the normal Open position.

again. Repeat this procedure until the zipper operates correctly.

Water: Seeping through at the seams may be stopped by applying 3-M Scotchgard® on the inside of the seams. Rips in the fabric may be repaired with

Bondex® iron on patches. Iron the patches to the Inside of the top, carefully following the Bondex® instructions.

Snaps: Keep snaps cleaned and lubricated with silicone to help prevent snaps from sticking to the studs. If a snap does become stuck to a stud, use a

screwdriver and GENTLY pry apart to prevent permanent damage to the snap or the top fabric.

Damaged Slider -

Jaws Spread Apart

(sometimes broken)

Normal Slider -

Jaws Parallel

Fabric: The fabric should be washed often using soap, warm water and a soft bristle brush. Rinse with clear water to remove all traces of soap. Bestop recommends using Bestop

Cleaner (part no. 11201-00) and Bestop Twill Protectant (part no.11207-00) or Bestop Protectant (part no. 11202-00). Bestop Cleaner and Bestop protectant are specially formulated

to provide a total cleaning and protection system. Bestop Cleaner safely removes the toughest stains, will not harm vehicle nishes, is biodegradable and environmentally friendly.

Bestop Protectants protect against fading, cracking and hardening, and repel dust, grease, dirt and mildew.

Installation Instructions

Sunrider for Hardtop

Vehicle Application:

Jeep® Wrangler JL 2 Door and 4 Door 2018-current

Jeep® Gladiator 2020-current

Part Number 52454

Soin et entretien de votre produit Bestop

Tissu : Bestop

Cleaner (pièce no 11201-00) et Bestop Twill Protectant (pièce no 11207-00) which qui sont spécialement formulés pour fournir un système complet de nettoyage et de protection.

Vitres : Maintenir les vitres propres pour éviter de les égratigner. NE PAS utiliser une brosse sur les fenêtres. Laver avec un chiffon ou une éponge imbibée d’eau et d’un savon à vaisselle doux. Bestop recom-

mande Bestop Vinyl Window Cleaner (no de pièce 11203-00), lequel nettoie et protégé les vitres de vinyle et aide à prévenir les dommages causés par les UV. NE JAMAIS ESSUYER LES VITRES ALORS

Fermetures à glissière : 1206-00)

de Bestop aidera à protéger des dommages et maintiendra les fermetures à glissière en bon état de fonctionnement. Si une fermeture à glissière

ouvre derrière la glissière, la glissière peut avoir été forcée au point de s’ouvrir. Le problème peut habituellement être réparé en utilisant des pinces

ordinaires pour remettre les côtés parallèles. Remettre la glissière au bout de la fermeture à glissière, dans la position Ouverte normale. Serrer

ment à l’aide des pinces et essayer la fermeture à glissière de nouveau. Répéter le processus jusqu’à ce que la fermeture à glissière fonctionne

correctement.

Eau :

peuvent être réparées grâce aux pièces thermocollantes Bondex®. Fixer les pièces thermocollantes à l’aide d’un fer à repasser sur l’intérieur du toit, en suivant

soigneusement les instructions de Bondex®.

Boutons pression : Maintenir les boutons pression propres à l’aide de silicone pour empêcher les boutons pression de coller aux rivets. Si un bouton pression

reste collé à un rivet, utiliser un tournevis et appliquer une F

Glissière normale -

Mâchoires parallèles

Glissière endommagée -

Mâchoires écartées

(parfois brisées)

Cuidado y mantenimiento de su producto Bestop

Su producto Bestop está hecho con materiales de la más alta calidad. Para mantener su aspecto nuevo y alargar su vida útil al máximo posible, necesitará limpieza y mantenimiento periódicos.

Tela: debe lavar la tela con frecuencia usando jabón, agua tibia y un cepillo de cerdas suaves. Enjuague con agua limpia para eliminar todos los residuos de jabón. Bestop recomienda usar Bestop Cleaner

(núm. de parte 11201-00) y BestopTwill Protectant (núm. de parte 11207-00) que están formulados especialmente para proporcionar un sistema de limpieza y protección total.

Ventanas: mantenga las ventanas abiertas para evitar que se rayen. ¡NO use cepillo para lavar las ventanas! Lave con un paño o esponja empapado de agua y un detergente suave para lavar platos. Bestop

recomienda usar el limpiador de ventanas de vinilo Bestop (número de parte 11203-00), que limpia de manera segura y protege las ventanas de vinilo, además de ayudar a prevenir daños causados por los

rayos UV. NUNCA LIMPIE LAS VENTANAS CUANDO ESTÉN SECAS. Tenga cuidado cuando limpie la nieve o escarcha de las ventanas de vinilo, ya que se rayan con facilidad y pueden agrietarse a temper-

aturas bajas. NO baje las ventanas laterales o la ventana de la parte posterior cuando haga frío. Las ventanas pueden ponerse rígidas y agrietarse. Esta garantía no cubre las grietas causadas por mal uso en

temperaturas frías.

Cremalleras: conserve las cremalleras limpias y lubricadas con el limpiador de cremalleras Bestop (número de parte 11206-00), que ayuda a pre-

venir daños y mantiene las cremalleras en óptimas condiciones de funcionamiento. Si la cremallera se abre detrás de la corredera, es posible que

las mordazas de la corredera se hayan separado. Por lo general, este problema se repara fácilmente con un par de pinzas comunes para volver a

poner los lados en paralelo. Regrese la corredera al extremo de la cremallera en la posición abierta normal. Apriete un poco al principio y pruebe

hasta que la cremallera funcione correctamente.

Agua:

repararse con parches Bondex® que se aplican con plancha. Planche los parches en el interior de la capota, siguiendo con cuidado las instrucciones de Bon-

dex®.

Broches: conserve los broches limpios y lubricados con silicona para evitar que se peguen a los corchetes de encaje. Si un broche se queda pegado a un cor-

chete, use un destornillador y CON CUIDADO separe las dos piezas para evitar daño permanente al broche o a la tela de la capota.

Corredera normal:

Mordazas paralelas

Corredera dañada:

Mordazas abiertas (a

veces, rotas)

Vehicle Application:

Jeep® Wrangler JL 2 Door and 4 Door 2018-current

Jeep® Gladiator 2020-current

Part Number 52454

Warranty Information

Sunrider for Hardtop

WHAT BESTOP WARRANTS

Subject to the terms and conditions of sale, including any terms and conditions set forth by Bestop, Inc. (“Bestop” or “us” or “we”) in our then-current terms of

sale on our website (collectively, the “Terms”), Bestop represents and warrants that: the covered products listed in the “Covered Products and Warranty Periods”

section (a “Product”) will substantially be free from defects in materials and workmanship for the specied warranty periods set forth in that section.

THE WARRANTY IS LIMITED AND CONDITIONAL

This warranty applies to the original purchaser of the Product only. The warranty is valid only as long as the original retail purchaser owns the vehicle upon which

the Product is installed. The warranty expires should the Product be removed from the original vehicle or if the original vehicle is transferred to another owner.

This warranty is not transferable or assignable. The warranty does not apply to Product bought from auction-style or price-bid websites.

THE LIMITED WARRANTY AND STATED REMEDIES ARE SOLE AND EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES, AND COMPANY

EXPRESS DISCLAIMS ALL IMPLIED OR STATUTORY OR OTHER WARRANTIES, INCLUDING WITHOUT LIMITATIONS WARRANTIES OF MERCHANTABILITY,

NON-INFRINGEMENTOR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL COMPANY BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSE-

QUENTIAL, PUNITIVE, INDIRECT OR EXEMPLARY DAMAGES OF ANY KIND, INCLUDING LOST PROFITS OR REVENUE, HOWEVER CAUSED, WHETHER FOR

BREACH OR REPUDIATION OF CONTRACT, TORT, BREACH OF WARRANTY, NEGLIGENCE, OR OTHERWISE, WHETHER OR NOT COMPANY WAS ADVISED

OF THE POSSIBILITY OF SUCH LOSS OR DAMAGES.

Some states do not allow exclusion or limitation, so this may not apply to you. This warranty gives you specic legal rights, and you may have other rights which

vary from state to state.

EXCLUSIONS TO THE WARRANTY

The Limited Warranty excludes, and Bestop is not liable in any way for any warranty claims, damages, or defects related to:

• Misuse, abuse, accidents, vandalism, negligence, re, or improper installation or modication, or improper or inadequate maintenance;

• Failure to comply with any Product documentation, Bestop instructions, or applicable law or regulations; use in extreme conditions

• Force Majeure including but not limited to, earthquake, hurricane, tornado, ooding, or other disasters natural or man-made, civil unrest, strikes, declared or

undeclared war, or lack of performance by, or discontinued product of, supply chain partners whose products, software, operations or management is beyond the

control of Bestop;

• Damage resulting in breakage (including without limitation, spontaneous breakage, accidental breakage or breakage by any other means)

of a Product or any component part;

• Damage to vinyl windows due to misuse, or cracking due to varying weather conditions.

YOUR SOLE REMEDY

During the applicable warranty period, Bestop shall, at its option, either repair or replace any Product that it conrms, in its discretion, is non-compliant with the

warranties herein. Bestop will not pay for labor charges associated with installation or removal of the Product. Should a specic Product be discontinued, Bestop

may, at its option, replace the discontinued Product with a current product or like product.

Please retain your proof of purchase. Original proof of purchase for the Product must accompany any warranty claim. If you have a warranty claim, rst you must

email Bestop Customer Service at [email protected] for instructions. All claims must be emailed to [email protected] within 30 days of

discovery of a defective Product, but in no event later than thirty days after the end of the applicable Warranty Period (the “Warranty Notice Period”). Warranty

claims made after the Warranty Notice Period are null and void and Bestop shall have no responsibility with respect to such claims.

THIS SECTION SETS FORTH BESTOP’S SOLE OBLIGATION & YOUR SOLE REMEDY WITH RESPECT TO ANY DEFECTS OR OTHER PRODUCT ISSUE. ANY

PRODUCTS REPLACED UNDER TERMS OF THIS WARRANTY WILL BE COVERED UNDER TERMS & BALANCE OF THE DURATION OF THE ORIGINAL LIMITED

WARRANTY FOR SUCH PRODUCT.