Vermeiren Turios Manuel utilisateur

User manual

M A N U E L D ' U T I L I S A T I O N

G E B R U I K S A A N W I J Z I N G

G E B R A U C H S A N W E I S U N G

M A N U A L E D I I S T R U Z I O N I

M A N U A L D E I N S T R U C C I O N E S

I N S T R U K C J A O B S

Ł

U G I

N Á V O D K O B S L U Z E

Turios

Instrukcje dla wyspecjalizowanego

Alle rechten, inclusief vertaling, voorbehouden.

Alle Rechte, auch an der Übersetzung, vorbehalten.

traducción.

Wszelkie prawa zastrzeżone, łącznie z tłumaczeniem.

Všechna práva vyhrazena, včetně překladu.

EN

Instructions for specialist dealer

This instruction manual is part and parcel of the

product and must accompany every product

sold.

Version: D, 2022-01

FR

Instructions pour les distributeurs

Ce manuel d'instructions fait partie du produit et

doit accompagner chaque produit vendu.

Version : D, 2022-01

NL

Instructies voor de vakhandelaar

Deze handleiding is deel van het product en

dient bij iedere product te worden geleverd.

Versie: D, 2022-01

DE

Hinweise für den Fachhändler

Diese Gebrauchsanweisung ist Bestand-teil des

Produkts und ist bei jeder Produkts

auszuhändigen.

Version: D, 2022-01

IT

Istruzioni per il rivenditore

Il presente Manuale di istruzioni è parte

integrante del prodotto e deve essere fornito

assieme alla prodotto.

Versione: D, 2022-01

ES

Instrucciones destinadas a los distribuidores

especializados

El presente manual de instrucciones es parte

integrante del producto y se debe adjuntar a

todas las producto que se vendan.

Versión: D, 2022-01

PL

sprzedawcy

Niniejsza instrukcja obsługi jest nieodłączną

częścią produktu i musi być dołączona do

każdego sprzedawanego produktu.

Wersja: D, 2022-01

CS

Pokyny pro specializovaného prodejce

Tento návod k obsluze je součástí dodávky a

musí být součástí každého prodaného

produktu.

Verze: D, 2022-01

Basic UDI: 5415174 122127Turios 2P

Multi version: D, 2022-01

Language index

English

Français

Nederlands

Deutch

Italiano

Español

Polski

Czech

User manual

Manuel d'utilisation

Gebruiksaanwijzing

Bedienungshandbuch

Manuale di istruzioni

Manual de instrucciones

Instrukcja obsługi

Návod k obsluze

This page is intentionally left blank

Turios

2022-01

Content

1

EN

NL

Content

Content ....................................................................................................................... 1

Preface........................................................................................................................ 2

1 Your product .................................................................................................. 3

1.1 Accessories ................................................................................................... 3

2 Before use ..................................................................................................... 4

2.1 Intended use ................................................................................................. 4

2.2 General safety instructions ............................................................................ 4

2.3 Symbols on the wheelchair ........................................................................... 5

2.4 Transport ....................................................................................................... 5

2.5 Assembly/Disassembly ................................................................................. 8

2.6 First use and storage .................................................................................... 9

3 Using your wheelchair ................................................................................ 10

3.1 First ride ...................................................................................................... 10

3.2 Driving outdoors .......................................................................................... 10

3.3 Operating console ....................................................................................... 11

3.4 Brake and free-wheel lever ......................................................................... 12

3.5 Moving to/from wheelchair .......................................................................... 13

3.6 Comfort adjustments ................................................................................... 13

3.7 Battery status and charging ........................................................................ 14

4 Maintenance ................................................................................................ 15

4.1 Time of maintenance ................................................................................... 15

4.2 Instructions for maintenance ....................................................................... 15

4.3 Troubleshooting .......................................................................................... 16

4.4 Expected lifespan ........................................................................................ 17

4.5 Reuse .......................................................................................................... 17

4.6 End of use ................................................................................................... 17

5 Technical specifications ............................................................................. 18

Turios

2022-01

Preface

2

EN

NL

Preface

Congratulations! You are now owner of a Vermeiren wheelchair!

This wheelchair is made by qualified and committed personnel. It is designed and produced

according to high quality standards guarded by Vermeiren.

Thanks for your trust in the products of Vermeiren. To support you on the use of this wheelchair

and its operating options, this manual is offered. Please read it carefully; it will help you to get

familiar with the operation, capabilities and limitations of your wheelchair.

If you still have questions after reading this manual, do not hesitate to contact your specialist

dealer. He/she will be glad to help you on this subject.

Important note

To ensure your safety, and to prolong the lifetime of your product, please take good care of it and

have it checked and serviced on a regular basis.

This manual reflects the latest product developments. Vermeiren has the right to implement

changes to this type of product without being imposed to any obligation to adapt or replace similar

products previously delivered.

Pictures are used to clarify the instructions in this manual. Details of the depicted product may

deviate from your product.

Information available

On our website http://www.vermeiren.com/ you will always find the most recent version of

following information. Please consult this website regularly for possible updates.

Visually impaired people can download the electronic version of this manual and have it read out

by means of a text-to-speech software application.

This user manual

For user and specialist dealer

User manual of applied operating console and battery charger.

For user and specialist dealer

Installation instructions (Instructions for detail adjustments and (dis)assembly)

For specialist dealer

Service manual for wheelchairs

For specialist dealer

EC declaration of conformity

Turios

2022-01

Your product

3

EN

NL

1 Your product

1. Backrest

2. Operating console

3. Armrest

4. Seat

5. Footrest

6. Footplate

7. Safety belt

8. Battery housing

9. Front wheels

10. Driving motors

11. Rear wheels / Driving wheels

12. Front lights (optional)

13. Identification plate

1.1 Accessories

The following accessories are available for the electric wheelchair Turios:

• Leg support (BZ7, BZ8)

• Headrest (L55, L58)

• Lights

• Crutch holder

• Cup holder

• Mirror

• Swing-away operating console

• Top case

1

2

3

4

5

6

7

8

9

10

11

12

14

Turios

2022-01

Before use

4

EN

NL

2 Before use

2.1 Intended use

In this paragraph a brief description of the intended use of your wheelchair is given. Additionally,

relevant warnings are added to the instructions in the other paragraphs. In this way we would like

to make you aware of the possible misuse that may appear.

• This wheelchair is suitable for indoor and outdoor use.

• This wheelchair is designed and produced solely to transport/transfer one (1) person with a

maximum weight of 130kg. It is not designed for transportation of goods or objects, nor for any

use other than previously described.

• This wheelchair can be operated by the user sitting in the wheelchair, or it can be pushed by

an attendant. You should NOT use this wheelchair without attendant if you suffer from physical

or mental impairments that may put you, or other people, in danger when driving the

wheelchair. For this reason, consult your doctor first and make sure that your specialist dealer

is informed about his advice.

• Only use accessories and spare parts approved by Vermeiren.

• Please read all technical details and limits of your wheelchair in chapter 5.

• The warranty on this product is based on normal use and maintenance as described in this

manual. Damage to your product caused by improper use or lack of maintenance will cause

the warranty to lapse.

2.2 General safety instructions

Risk of injuries and/or damage

Please read and follow the instructions in this manual. Otherwise you may get injured or your

wheelchair may get damaged.

Keep the following general warnings in mind during use:

• Do not use your wheelchair if you are under influence of alcohol, medicines or other

substances that may influence your driving abilities.

• Be aware that some parts of your wheelchair may get very hot or cold due to ambient

temperature, solar radiation, heating devices or due to the motor drive during the ride. Be

careful when touching. Wear protective clothing if the weather is cold. After a ride, wait until

the wheelchair/motor has cooled down.

• Before switching the wheelchair on, be aware of the environment/situation in which you are

located. Adjust your speed to this before driving off. We advise you to use the slowest speed

setting to drive indoors. For outdoor driving you can adjust the speed to a suitable speed at

which you feel comfortable and safe.

• ALWAYS keep in mind that your wheelchair may stop suddenly due to a discharged battery

or a protection that prevents your wheelchair from further damage. Also check the possible

causes mentioned in § 4.3. Use your safety belt to prevent injuries.

• Your wheelchair has been tested for electromagnetic compatibility and complies with the

standard, see chapter 5. Nevertheless, sources of electromagnetic fields may influence the

driving performance of your wheelchair, such as the fields of mobile phones, power

generators or high-power energy sources. On the other hand, the electronics of your

wheelchair can affect other electronic appliances too, such as alarm systems of shops and

automatic doors. We therefore advise you to check your wheelchair regularly for damage and

wear, since these may enlarge the interference (see also chapter 4).

• Only drive on flat surfaces where both driving wheels touch the ground and where there is

sufficient contact to operate the wheelchair safely.

CAUTION

Turios

2022-01

Before use

5

EN

NL

• Alterations or substitutions should not be made to the wheelchair securement points or to

structural and frame parts or components without consulting the wheelchair manufacturer.

• Make sure that your hands, clothes, belts, buckles or jewellery don’t get caught by wheels or

other moving parts during use.

Be aware that your wheelchair may interfere with some types of anti-theft systems, depending on

the settings used. This may cause the shop's alarm to go off.

In case a serious incident has occurred involving your product, notify Vermeiren or your specialist

dealer as well as the competent authority in your country.

2.3 Symbols on the wheelchair

The symbols in following list are applicable to your wheelchair. Symbols can be found in the

relevant ISO standard (ISO 7000, ISO 7001 and IEC 417).

Maximum weight of the user in kg

Indoor/outdoor use (battery charger excluded)

Indoor use only (battery charger)

Maximum safe slope in ° (degrees).

Maximum speed

Type designation

Risk of entrapment

2.4 Transport

Risk of damage

Take action to protect the wheelchair from being damaged during transport.

2.4.1 Moving out of the way

Use the operating console to drive the wheelchair to its destination.

Otherwise, put the wheelchair in free-wheel mode (see §3.4) and use the push bar to move it.

2.4.2 Transport by aircraft

Since the wheelchair is equipped with non-spillable AGM batteries, it is possible to transport the

wheelchair (as a whole) by aircraft. Consult your airline for the correct handling procedures before

booking your flight. Before handing your wheelchair over to the airport personnel, disconnect the

battery from the wheelchair, see installation manual.

CAUTION

Turios

2022-01

Before use

6

EN

NL

2.4.3 Transport by vehicle, as luggage

The best way to transport your electric wheelchair in the car is to drive it by using ramps. If you

are not experienced to drive the electric wheelchair using ramps, you can put the wheelchair in

neutral mode and push the wheelchair in the car using ramps. If necessary, disassemble the

wheelchair.

1. As the wheelchair user, transfer to a car seat, see §3.5.

2. Remove all moveable parts prior to transport (footrests, arm supports, etc.).

3. Store moveable parts safely behind the passenger seat or in the luggage compartment.

4. Drive or push the electric wheelchair in the car using ramps, or lift the wheelchair in the car

with the help of 2 persons by grasping the fixed parts of the frames.

5. Attach the solid parts of the frame securely to the vehicle.

6. Place the wheelchair in drive mode (engaging the parking brakes) and check that the operating

console is switched off.

2.4.4 Transport by vehicle, as seat for user

The wheelchair has passed the crash test of ISO 7176-19: 2008 and, as such, has been

designed and tested for use only as forward-facing seat in a motor vehicle.

The wheelchair is tested dynamically with the ATD (anthropomorphic test device) using a

four-points strap-tie system and a 3-point occupant-restraint system. Nevertheless, the user

should preferably be transferred to one of the seats inside the vehicle and use vehicle’s

restrain system. The wheelchair should be stored as luggage in a separate (cargo)

compartment, see §2.4.3 .

Risk of injuries and damage

Use wheelchair's pelvic belt and the applicable three-points belt in the vehicle to prevent

head and chest impacts with the vehicle.

Do not use postural supports to restrain the user in the vehicle unless they are labelled as

being in accordance with the requirements specified in ISO 7176-19:2008.

Following involvement in any type of vehicle collision, have your wheelchair inspected by

the specialist dealer or manufacturer’s representative before reuse.

Securing the wheelchair

1. Make sure that the vehicle has a suitable wheelchair four-points strap-tie-down and occupant-

restraint system conform ISO 10542, and that both systems are not frayed, contaminated,

damaged or broken.

2. Use the operating console to return your wheelchair to stable position, see §3.5.

3. Remove all mounted accessories such as trays and respiratory equipment and secure them

in a safe place. If not possible, secure them to the wheelchair but positioned away from the

occupant with energy-absorbing padding placed between tray and user.

4. Use a ramp to drive the wheelchair (with user) in the vehicle according to the instructions in

§3.2.1.

5. Position the user facing forward in the travelling direction, centrally between the tie-down rails

mounted in the floor of the vehicle.

6. Make sure that the user is sitting as upright as possible. If the user's condition prevents this,

carry out a risk assessment to evaluate the user's safety during transit.

7. Turn the operating console OFF and make sure that the free-wheel lever is in braking mode,

see §3.4.

8. The location of each securement point on the wheelchair is marked with the

following symbol:

9. Verify that the tiedown end-fitting is compatible with the wheelchair securement

points.

WARNING

Turios

2022-01

Before use

7

EN

NL

10. Attach the front securement-strap hooks to the securement points (A) on the wheelchair

following the supplier instructions of the strap-system.

11. Turn free-wheel lever in free-wheel position and roll the wheelchair backwards to pull the front

straps tight, see §3.4.

12. Attach the rear securement-strap hooks to the securement points (B) on the rear in the same

way.

13. Turn free-wheel lever back in braking position, see §3.4.

Securing the user

1. Attach the wheelchair’s pelvic belt.

2. Attach the user-restraint belts of the vehicle according to

the instructions of the strap-system manufacturer.

Wear the pelvic belt low across the front of the pelvis,

so that the angle of the pelvic belt is within the

preferred zone of 30° to 75° to the horizontal, similar

to that shown in the figure.

A steeper (greater) angle within the preferred zone is

desirable.

3. Adjust the belt tightly according to the instructions of the strap-system manufacturer,

consistent with the user's comfort.

4. Ensure that the restraint belt connects in a straight line to the anchor point in the vehicle and

that no bends in the belt are visible, for instance at the axle of the rear wheel.

5. Position the seatbelt buckle so that the release button will not be contacted by wheelchair

components during a crash.

6. Make sure that belts are not twisted or held away from the body as shown in figure 1.

7. Make sure that the shoulder-belt restraints fit over the shoulders, see figure 2.

B

A

Turios

2022-01

Before use

8

EN

NL

Belt restraints must not be held away

from the body by wheelchair

components such as armrests or

wheels.

Belt restraints make full contact with

shoulder, chest and pelvis.

Pelvic belt low on the pelvis near the

thigh-abdominal junction

Improper belt-restraint fit

Proper belt-restraint fit

2.5 Assembly/Disassembly

Risk of injuries

• Make sure that your fingers, clothes, buckles won’t get trapped during (dis)assembly.

Your dealer delivers the wheelchair fully assembled and explains the various operating elements

and their use. We also provide a further, detailed explanation of the different parts here for

transport purposes.

To assemble the electric wheelchair:

1. Mount the arm supports (paragraph 2.5.1).

2. Mount the footrests (paragraph 2.5.2).

To disassemble the electric wheelchair do the reverse of the above instructions.

2.5.1 Mounting or removing the arm support

Risk of injuries and/or damage

• Check that the arm pads are at the same height on each side.

Mount the armrest (1) by sliding the support rod (2) down into the

frame (3).

To remove the armrest (1), lift it up and out of the seat frame.

CAUTION

1

2

3

✓

Turios

2022-01

Before use

9

EN

NL

2.5.2 Mounting or removing the footrest

To install

1. Hold footrest (4) sideways and hang it in footrest support (5).

2. Swing the footrest inwards until it clicks in position.

To remove

1. Pull footrest lever (6) and swing footrest (4) outwards.

2. Lift the footrest to remove it.

2.6 First use and storage

Risk of battery damage

• Never completely discharge the battery.

• Do not interrupt the charging cycle; only disconnect the battery charger when the battery is

fully charged.

• Make sure that your wheelchair is stored dry to prevent mould from growing and the upholstery

from being damaged.

• Check the technical details for storage, see chapter 5.

Ensure that the battery has been fully charged before using your wheelchair, ask your dealer if

this has already been done or not. To charge, follow the charging instructions in §3.7.

CAUTION

4

5

6

Turios

2022-01

Using your wheelchair

10

EN

NL

3 Using your wheelchair

Risk of injuries

• First read previous chapters and inform yourself about the intended use. Do NOT use your

wheelchair unless you have read and fully understood all instructions.

• Also read the instructions in the operator console manual and battery charger manual!

• In case of doubts or questions, do not hesitate to contact your local specialist dealer, your care

provider or technical adviser to help you with this.

3.1 First ride

Risk of injuries and damage

• Always keep the swing range of footrest and operating console in mind to prevent bystanders

from being injured or objects from being damaged.

• Always unplug the battery charger from the wheelchair before starting to drive.

• Make sure that you are familiar with the operation of your wheelchair before using it in

crowded and possibly dangerous places. First exercise at a specious, open area with

little bystanders.

• Investigate the effects of shifting the centre of gravity on the behaviour of the wheelchair,

for example on up or down gradients, on laterally sloping ground, or when overcoming

obstacles. Obtain support from an attendant.

• The surface of the controller gets slightly warm during use.

• While driving backwards, the speed is reduced.

1. Make sure that:

• the wheelchair is on a flat surface;

• the battery is fully loaded, see § 3.7;

• The motor is coupled, see § 3.4;

• the tyres have the correct tyre pressure, see § 4.2.1;

• the wheelchair is adapted to your needs and comfort, see §3.6;

• you have the proper sitting position, see § 3.5.

2. Follow the instructions in the operating console manual.

3. Switch on your wheelchair.

4. Turn the speed control to the lowest speed setting.

5. Exercise how to drive and make adjustments to the wheelchair.

6. If you feel confident enough, you can try to drive at higher speed.

7. Now try to turn, in forward and backward direction. Repeat this a few times.

8. Make sure that your wheelchair stands stable, when ending the ride.

9. Switch off your wheelchair.

3.2 Driving outdoors

Risk of accident - Adjust your driving behaviour and speed.

• Take the local road traffic law into consideration; it may differ per country. This counts for

driving on pavements, unpaved roads or paved roadways.

• Do not drive on roads with heavy traffic.

• Take the weather conditions into consideration. Avoid driving by moist weather, extreme heat,

snow, black ice, freezing temperatures; see technical specifications in chapter 5.

• Even with your wheelchair lights on, it is not suitable to drive on public roads at poor visibility

(darkness, mist, twilight). Make sure that you are well visible, also during daylight hours, by

WARNING

CAUTION

WARNING

Turios

2022-01

Using your wheelchair

11

EN

NL

using fluorescent clothing and/or by using own lighting at the front and rear side of the

wheelchair.

• Be aware of other road users to whom your wheelchair may be an obstacle. Pay special

attention during turning and reversing. If you are not acquainted with how to drive backwards,

first practice in an open area. Indicate the direction you are intending to go before turning.

• Try to drive straight in small passages to prevent getting trapped.

• Keep the braking distance in mind. Be aware that the braking distance depends on speed,

surface, weather conditions, slope and weight of the user.

3.2.1 Cope with slopes, kerbs, obstacles or ramps

Risk of injuries by unexpected movement

• Use a restraining safety belt to secure yourself sitting in the wheelchair.

• Pay attention if the road is sandy, has soft ground, holes or gaps that may cause entrapment

of the wheels and/or decreasing of the traction of the driving wheels.

• Do NOT drive on slopes, obstacles, steps or kerbs larger than the size described in the

technical specifications in chapter 5.

• Always approach a kerb from the front.

• Do not put your wheelchair in free-wheel mode on a slope. The wheelchair may start moving,

causing injuries to you or bystanders.

• Do not use your wheelchair on an escalator or stairs.

• Only use ramps approved by Vermeiren and do not exceed their maximum load.

• To safely overcome obstacles or slopes, put the wheelchair in its most upright sitting position.

Risk of damage

• Always park your electric wheelchair on horizontal flat surfaces and on sites that are easily

accessible.

• If necessary, take a short run-up to speed up the wheelchair to mount a slope, obstacle, kerb

or ramp. Prevent that you or your wheelchair has to cope with a large recoil.

• Make sure that the wheelchair does not touch the ground or ramp due to the inclination of the

wheelchair.

• Be aware that the braking distance on downhill slopes can be significantly larger than on level

ground.

Procedure

• Start your drive according to the instructions in § 3.1, step 1.

• To move the wheelchair up or down stairs/steps, use lifting equipment or a ramp. If these

are not available, it can be lifted manually by at least two persons, grasping the frame firmly

with both hands. Do not use the backrest, footplate(s), armrests, or wheels to grasp the

wheelchair.

• To cope with obstacles or inclinations:

1. Adjust the wheelchair to its most stable position, see § 3.5.

2. Drive as slow as possible to cope with the obstacle or inclination.

3.3 Operating console

Risk of injuries or damage

• Be aware that the stability decreases when the wheelchair is adjusted from sitting-straight to

inclined position.

• Make sure there is enough space around the wheelchair to operate backrest and seat.

CAUTION

When you stop on a slope, the brake will work automatically to prevent the wheelchair from

running forward or backward.

Turios

2022-01

Using your wheelchair

12

EN

NL

How to use the operating console is described in a specific user manual, enclosed with the

delivery of your wheelchair. If this manual is missing, contact your specialist dealer

immediately.

Put the joystick in the neutral (central) position before pressing the on/off button, otherwise

the electronics will be blocked. To release this block, switch the operating console off and

on again.

Technical protections

The operating console enables you to control all driving components and motors to adjust your

body position. For your own safety, and to prevent that the wheelchair gets damaged, movements

are monitored by the electronics. This may result in block of movement, speed decrease or

complete stop. Consult the user manual of the operating console for more information.

To avoid accidental battery run down, your wheelchair is equipped with an automatic power

shutdown system. This system switches off the operating console automatically when it is not

operated for a while. If this occurs, simply switch your console back on.

3.4 Brake and free-wheel lever

Risk of injuries or damage

• Only operate the free-wheel lever when your wheelchair is turned OFF. An attendant should

operate the free-wheel lever. NEVER operate it from sitting position.

• Do not use the free-wheel mode on slopes and inclinations, see symbol on motor:

Make sure that the free-wheel lever is in its braking position BEFORE switching the

wheelchair ON. Electromagnetic brakes do NOT function if the wheelchair is in free-wheel

mode. This is indicated on the operating console. Driving is not possible.

Your wheelchair is equipped with electromagnetic brakes. The working of the brakes depends on

the position of the free-wheel lever (1).

The EM brakes function automatically, only if free-wheel lever (1) is in braking position. In this

situation, the brakes start braking if:

• the wheelchair is OFF;

• the wheelchair is ON and the

joystick is released.

Releasing the joystick makes the

wheelchair stop gently and activates

the brakes.

Operation of free-wheel lever:

• Turn levers to the rear to put the

wheelchair in free-wheel mode.

Now, the motor is disconnected.

The wheelchair can be moved

manually.

• Turn levers inwards to connect

the motor to the drive. This

should be done before starting

the wheelchair.

CAUTION

Neutral

Drive

1

Turios

2022-01

Using your wheelchair

13

EN

NL

3.5 Moving to/from wheelchair

Risk of injuries or damage

• In case you cannot perform the transfer in a safe manner, ask someone to assist you.

• Do not stand on the footplate(s) during transfer into or out of the wheelchair.

Transfer

1. Position the wheelchair as close as possible to you when sitting in your chair, couch, seat or

bed.

2. Apply the brakes by turning the free-wheel lever to braking position, see § 3.4.

3. Fold the footplate(s) upwards to prevent standing on them.

4. If necessary, remove one armrest to make room, see § 2.5.1.

5. Transfer to/from the wheelchair using the strength of your arms or with the help of attendant(s)

or lifting equipment.

Sitting in the wheelchair

1. Sit down on the seat with your lower back against the backrest.

2. Turn the footplate(s) down and put your feet on the footplates.

3. Replace the armrest, if applicable.

4. Make sure that your upper legs are horizontal and that your feet are in a comfortable position.

Adjust if necessary.

5. Make sure that your arms are bent and are resting comfortably on the arm pads. Adjust if

necessary.

Adjusting to stable position

For transport purposes and when you need to negotiate obstacles, the wheelchair must be

adjusted to maximise its stability:

• Backrest upright

• Footplate folded up

3.6 Comfort adjustments

Risk of injuries or damage

• The following comfort adjustments can be done by the attendant or caretaker. All other

adjustments are done by your specialist dealer according to the installation instructions, see

preface.

• Make sure that your fingers, clothes, buckles don’t get trapped during adjustment.

3.6.1 Backrest inclination (manual version)

1. Pull the strap at the bottom of the backrest to unlock the mechanism.

2. Adjust the backrest to the desired position (0° - 32°, 4 steps of 8°).

3. Release the strap. Make sure that the backrest is well secured.

3.6.2 Backrest inclination (with gas spring)

The backrest inclination with gas spring is operated by means of a lever. Depending on your

chosen configuration upon ordering, the lever is located on the backrest, or on the right side of

the seat.

1. Pull the lever.

2. Pull/Push the backrest to the desired position.

3. Release the lever. Make sure that the backrest is well fixed.

CAUTION

Turios

2022-01

Using your wheelchair

14

EN

NL

3.7 Battery status and charging

Risk of injuries and damage due to fire

• Only use the battery charger delivered with the wheelchair. The use of any other charger may

be dangerous (fire hazard).

• The battery charger is only intended to charge the batteries delivered with the wheelchair, not

to charge any other batteries.

• Do not adapt any of the delivered parts, like cables, plugs or battery charger. Never open or

change the battery or the connection points.

• Protect the battery and battery charger against flames, high and low temperatures (see chapter

5), moisture, sunshine, severe shocks (for example dropping). Do NOT use the battery if this

has been the case.

• Charge the battery with the battery charger, indoors, in a well-ventilated area, out of children's

reach.

• First read the user instruction of the applied battery charger before charging the wheelchair’s

battery. For more information, contact your specialist dealer or consult our website

http://www.vermeiren.com/

Risk of damage

• Battery self-discharge and the quiescent current of the connected users will drain the battery

charge slowly. The battery may be irreversibly damaged if the battery is fully discharged.

Therefore, make sure that the battery is charged on time (see manual of operating console).

• Read the storage and maintenance instructions in chapter 4 and technical

details in chapter 5.

• Only disconnect the battery charger when the battery is fully charged, see

the following symbols on the charger:

• Do not charge batteries below 0°C. Move the battery to a warmer place

and start charging.

• Keep the connection point for the battery charger free of dust and other

contamination.

• In case of any problems whereby the battery cannot be charged according to following

instructions, please contact your specialist dealer.

• For instructions on how to change the batteries, see the installation manual.

For all information on battery status indication, please read the manual of the operating

console.

It is recommended to unplug the battery charger from the mains when not in use. This is to

prevent unnecessary energy consumption.

To charge the battery:

1. FIRST connect the battery charger to a 230V AC power socket. Use the battery charger

directly, without extension cord, on the power supply (without time switch).

2. Plug the adapter in the charging point of the operating console.

3. Wait until the battery is fully charged. Consult the battery charger manual for more information.

4. Disconnect the battery charger.

5. Remove the battery charger from the socket, let it cool down and store it in the charger pocket.

WARNING

CAUTION

Turios

2022-01

Maintenance

15

EN

NL

4 Maintenance

4.1 Time of maintenance

Risk of injuries and damage

Repairs and replacements may only be undertaken by trained persons and only genuine

replacement parts of Vermeiren should be used.

The last page of this manual contains a registration form for the specialist dealer to record

each service.

The service frequency depends on the frequency and intensity of use. Contact your dealer to

agree to a common timetable for inspection/maintenance/repair.

Read the user instructions of the applied battery charger regarding maintenance.

For the maintenance manual, refer to the Vermeiren website: www.vermeiren.com.

Before each use

Inspect the following points:

• All parts: present, undamaged and unworn.

• All parts: clean, see § 4.2.2.

• Wheels, seat, arm rests, footrests and headrest (if applied): well secured.

• Battery status: charge the battery when necessary, see §3.7.

• Operating console, battery, power module, motors, battery charger, lights and relevant

cables: no damage such as wires that have become frayed, broken or exposed.

• Condition of wheels/tyres, see § 4.2.1.

• Condition of frame parts: no deformation, instability, weakness or loose connections.

• Seat, backrest, arm pads, calf pads and head rest (if applied): no excessive wear (like

dented spots, damage or tears).

Contact your specialist dealer for possible repairs or part replacements.

Every month

If your wheelchair is stored for a longer period, you still need to charge the batteries every month.

It is also possible to keep the battery charger connected to the battery and the mains during this

period. For more information, see § 3.7.

Yearly or more often

Have your wheelchair inspected and serviced by your specialist dealer, at least once a year, or

more often. The minimum maintenance frequency depends on use and should therefore be

commonly agreed upon with your specialist dealer.

If stored

Make sure that your wheelchair is stored in a dry environment to prevent mould from growing,

or the upholstery from being damaged.

4.2 Instructions for maintenance

4.2.1 Wheels and tyres

Proper working of the brakes depends on the state of the tyres, that can change due to wear

and contamination (water, oil, mud, …).

CAUTION

Turios

2022-01

Maintenance

16

EN

NL

• Keep your wheels free of wires, hair, sand and fibres.

• Check the profile of the tyres. If the tread depth is less than 1 mm, the tyres need to be

replaced. Contact your specialist dealer for this matter.

• Inflate the pneumatic tyres to the correct pressure (see pressure indication on the tyres).

• For instructions on how to change the tyres, see the installation manual.

4.2.2 Cleaning

Risk of damage by moisture

• Keep the operating console clean and protect it from water and rain.

• Never use a hose or high-pressure cleaner to clean the wheelchair.

Wipe all rigid parts of the wheelchair with a damp cloth (not drenched). If necessary, use a mild

soap, suitable for varnishes and synthetics.

The upholstery can be cleaned with lukewarm water and a mild soap. Do not use abrasive

cleaning agents to clean.

Keep the ventilation openings of the battery charger clean and free of accumulated dust. Blow

away the dust and clean the battery charger enclosure with a slightly moistened cloth, if required.

4.2.3 Disinfection

Risk of damage

Disinfections may only be undertaken by trained persons. Consult your specialist dealer.

4.3 Troubleshooting

Even if you use your wheelchair properly, a technical problem may occur despite this.

In this case, contact your local specialist dealer.

Risk of injuries and damage to the wheelchair

• NEVER attempt to repair your wheelchair yourself.

• For failures in the operating console you need to contact your specialist dealer.

He/She will decide if the console needs to be reprogrammed.

In case of failure, a fault code is displayed on the operating console.

For an overview of all fault codes on the operating console, please read the manual of the

operating console.

The following symptoms may indicate a serious problem. Therefore, always contact your

specialist dealer if you spot any of the following deviations:

• Strange sound;

• Frayed/damaged wiring harnesses;

• Cracked or broken connectors;

• Uneven tread wear at one of the tyres;

• Jerky movements;

• Wheelchair deflects to one side;

• Damaged or broken wheel assemblies;

• Wheelchair does not switch on (blown fuse);

• Wheelchair is powered but does not move, see 3.4.

CAUTION

WARNING

La page est en cours de chargement...

Vermeiren Turios Manuel utilisateur

Vermeiren Turios Manuel utilisateur

dans d''autres langues

Documents connexes