Fisher Paykel HP24ILTX1 Guide d'installation

INTEGRATED PERIMETER

INSERT VENTILATION HOOD

HP24ILTX1 and HP36ILTX1 models

HOTTE DE VENTILATION

PÉRIMÉTRIQUE ENCASTRABLE

Modéls HP24ILTX1 et HP36ILTX1

INSTALLATION GUIDE / USER GUIDE

GUIDE D’INSTALLATION / GUIDE D’UTILISATION

US CA

English Page 1 – 22

Français

Page 25 – 46

1

CONTENTS

Introduction 3

Safety and warnings 4

Installation instructions 7

Operating instructions 16

Cleaning and maintenance 17

Parts and accessories 19

Limited Warranty 20

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this user guide may

not be available in all markets and are

subject to change at any time. For current

details about model and specification

availability in your country, please go to

our website www.fisherpaykel.com or

contact your local Fisher & Paykel dealer.

Registration

Register your product with us so we can

provide you with the best service possible.

To register your product visit our website:

www.fisherpaykel.com

EN

3

INTRODUCTION

Thank you for purchasing a Fisher & Paykel product.

Thousands of hours go into the design, engineering, testing and perfecting of each

Fisher & Paykel appliance. The care and attention given to creating these beautiful

products doesn’t stop once it has found its home with you.

This use and care manual will answer most of your questions about the set-up, use

and on-going maintenance of your Fisher & Paykel product; however if you require

further information about your product and its use please consult our website for

solutions and further contact information to discuss with a service representative.

To ensure you receive all relevant product updates and the best service possible,

please register your Fisher & Paykel products through our website.

EN

5

SAFETY AND WARNINGS

IMPORTANT SAFETY INSTRUCTIONS

READ THE ENTIRE SET OF INSTRUCTIONS BEFORE INSTALLING OR USING

THIS APPLIANCE. Manuals can also be found on our website www.fisherpaykel.com.

●CAUTION: For general ventilating use only. Do not use to exhaust hazardous

or explosive materials and vapors.

●WARNING! To reduce the risk of fire, electric shock, or injury to persons, observe

thefollowing:

– Use this unit only in the manner intended by the manufacturer. If you have

questions, contact the manufacturer. For residential use only.

– Before servicing or cleaning unit, switch power off at service panel and lock

the service disconnecting means to prevent power from being switched on

accidentally. When the service disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag, to the service panel.

– Installation work and electrical wiring must be done by qualified person(s)

in accordance with all applicable codes and standards, including fire-rated

construction.

– Sufficient air is needed for proper combustion and exhausting of gases through

the flue (chimney) of fuel burning equipment to prevent back drafting. Follow

the heating equipment manufacturer’s guideline and safety standards such as

those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

– When cutting or drilling into wall or ceiling, do not damage electrical wiring

and other hidden utilities.

– Ducted fans must always be vented to the outdoors.

– This unit must be grounded.

●CAUTION: To reduce risk of fire and to properly exhaust air, be sure to duct air

outside – Do not vent exhaust air into spaces within walls or ceilings or into attics,

crawl spaces, or garages.

●WARNING: To reduce the risk of fire, use only metal ductwork.

●WARNING: To reduce the risk of fire or electric shock, do not use this fan with

any solid-state speed control device.

●WARNING: To reduce the risk of a range top grease fire:

– Never leave surface units unattended at high settings. Boilovers cause smoking

and greasy spillovers that may ignite. Heat oils slowly on low or medium

settings.

– Always turn hood ON when cooking at high heat or when flambéing food (ie

Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé)

– Clean ventilating fans frequently. Grease should not be allowed to accumulate

on fan or filter.

– Use proper pan size. Always use cookware appropriate for the size of the

surface element.

EN

6

SAFETY AND WARNINGS

●WARNING: To reduce the risk of injury to persons in the event of a range top

grease fire, observe the following*:

– SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then

turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go

out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

– NEVER PICK UP A FLAMING PAN – You may be burned.

– DO NOT USE WATER, including wet dishcloths or towels – a violent steam

explosion will result.

– Use an extinguisher ONLY if:

– You know you have a Class ABC extinguisher, and you already know

how to operate it.

– The fire is small and contained in the area where it started.

– The fire department is being called.

– You can fight the fire with your back to an exit.

●WARNING: Unplug or disconnect the appliance from the power supply before

servicing or cleaning.

READ AND SAVE THESE INSTRUCTIONS

* Based on “Kitchen Firesafety Tips” published by NFPA.

7

INSTALLATION INSTRUCTIONS

Contents of packaging

Installation instructions

User guide manual

(1)

Ventilation hood

(1)

3/8” (10mm)

Self tapping screw

(4)

Power connection box

(1)

6” (152mm) diameter

Ducting adapter with

back draft damper

(1)

US A

INS ALLATON NSTRUCT ONS

USER GUIDE

NST UCT ONS D’ NS ALL TION

GU DE D UT LI AT ON

HP 4 L X1 nd H 3 I TX mo e s

M èl HP 4 T 1 H 3 I T 1

I t gr t d Pe m t r ns rt en l t on H od

Ho e de V n l t o Pé mé rq e E c s r be

EN

8

INSTALLATION INSTRUCTIONS

Product and cabinetry cutout dimensions

K

L

ØM

A

E

B

G

D

P

F

C

I

J

H

O

N

UL power

connection box

Ducting adapter

9

INSTALLATION INSTRUCTIONS EN

HP24 HP36

PRODUCT DIMENSIONS inches (mm) inches (mm)

AOverall height of product 133/4” (350) 13 3/4” (350)

BOverall height of product (with

power connection box)

181/4” (463) 181/4” (463)

COverall width of product 207/8” (530) 3211/16” (830)

DOverall depth of product 11” (280) 11” (280)

EThickness of flange 1/16” (2) 1/16” (2)

FWidth of chassis 193/8” (492) 313/16” (792)

GDepth of chassis 101/16” (255) 101/16” (255)

HHeight of side of chassis 711/16” (195) 711/16” (195)

IWidth of top surface of chassis 113/4” (298) 113/4” (298)

JLength of angled surface of chassis 67/8” (175) 11” (280)

KDistance from center of ducting

outlet to back of chassis

31/8“ (80) 31/8” (80)

LDistance from center of ducting

outlet to side of chassis

95/8” (245) 159/16” (395)

MDiameter of ducting outlet 6” (152) 6” (152)

NDistance between center of lights 143/4” (375) 269/16” (675)

ODistance from center of light to

front of product

19/16” (40) 1 9/16” (40)

CABINETRY CUTOUT DIMENSIONS

Overall width of cutout 1911/16” (500) 311/2” (800)

Overall depth of cutout 101/4” (260) 101/4” (260)

PBase of brackets/clips to bottom of

chassis

min. 9/16” – max. 19/16”

(min. 15 – max. 40)

min. 9/16” – max. 19/16”

(min. 15 – max. 40)

IMPORTANT!

Actual product dimensions may vary by ± 1/16”(2mm).

Please read the entire instructions before installing the ventilation hood.

10

INSTALLATION INSTRUCTIONS

Height of ventilation hood

MINIMUM CLEARANCES inches (mm)

QHeight top of cooktop to base

of product

min. 26” – max. 30” (min 660 – max. 762)

This ventilation hood must be installed no lower than the minimum height indicated

in the table above. Minimum installation height may be greater if required by the

cooktop manufacturer or safety and warning section of this user guide. Installation

at the minimum height will improve the efficiency of capturing cooking odors, grease

and smoke. Installation at the maximum height improves user ergonomics by offering

increased head room.

Q

11

INSTALLATION INSTRUCTIONS

WARNING!

To reduce the risk of fire, use only metal ductwork. Do not use flexible plastic ducting

CAUTION!

To reduce risk of fire and to properly exhaust air, be sure to duct air outside – do not

vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or

garages.

Venting options

Attention should be given to ensure that any applicable regulations concerning the

discharge of exhaust air are fulfilled.

The ventilation hood can be installed to operate with the exhaust air ducted

externally from the kitchen.

Ducted

For ducted installation it is recommended that 6” (152mm) diameter, rigid or semi-rigid

ducting is used. This will require a 65/16” (160mm) (min) round hole in the ceiling or

wall. Care should be taken to position the hole correctly.

For optimal efficiency use the shortest and straightest duct route possible and use rigid

or semi-rigid ducting for reduced noise and increased airflow. Flexible metal ducting

should only be used as a last resort (ie in difficult installations) and if used ensure that it

is straight and smooth and extended as much as possible.

EN

12

INSTALLATION INSTRUCTIONS

WARNING!

●This appliance is heavy and requires two persons for unpacking and installation

●Installation work and electrical wiring must be done by qualified person(s) in

accordance with all applicable codes and standards.

●Failure to install the screws or fixing device in accordance with these instructions

mayresult in electrical hazards

IMPORTANT!

Wear gloves to protect against sharp edges.

The manufacturer is not liable for any damage caused by not following these instructions.

Installation

1 Prepare for installation.

Before installing your ventilation hood:

●Please read the instructions carefully.

●Unpack the ventilation hood and check that all

functions are working.

●Ensure that the voltage (V) and the frequency (Hz)

indicated on the serial plate match the voltage and

frequency at the installation site.

●The stainless steel surfaces of the ventilation

hood are very easily damaged during installation

if grazed or knocked by tools. Please take care to

protect the surfaces during installation.

●Protect the cooktop surface below with cardboard,

or the like, to prevent damage occurring whilst the

ventilation hood is being installed above.

2 Attach ducting adapter and power connection box to

the ventilation hood

●Place the ducting adapter onto the ventilation

hood and screw it in place using 3/8” (10mm)

screws.

●Place the power connection box onto the

ventilation hood and screw it in place using 3/8”

(10mm) screws.

●Follow wiring instructions described in the

‘Electrical connection’ section page15.

3 Provide an opening on the underside of the cupboard

(see product and cabinetry cutout dimensions).

It is also recommended that the cupboard has a door

or service panel that can be easily opened to access

the power connection box

width

depth

15

INSTALLATION INSTRUCTIONS

WARNING!

Electrical wiring must be done by qualified person(s) in accordance with all applicable

codes and standards and the unit must be grounded.

7 Electrical connection

●Run three wires, two for the power supply and one for the ground wire, from the

power connection box on the ventilation hood to a power connection point near

the installation.

●Open the power connection box on the ventilation hood and secure the power

conductor with a cULus listed strain relief (not included).

●Connect the power conductors to the conductors for the ventilation hood, black to

black and white to white.

●Connect the grounding wire (green or bare) to the ground conductor (green) of the

ventilation hood power connection box.

●Secure all the connections with cULus listed wire nuts.

●Replace the power connection box cover.

M

Switch

Interrupteur

Brown/Marron

Gray/Gris

Black/Noir

Red/Rouge

Blue/Bleu

Purple/Violet

White/Blanc

Yellow/Green

Jaune/Vert

White/Blanc

Yellow/Green Jaune/VertGround

Brown/Marron Motor

Gray/Gris

Black/Noir

Red/Rouge

Blue/Bleu

Black/Noir

White/Blanc

Black/Noir (L)

White/Blanc (N)

Green/Vert (E)

Black/Noir

White/Blanc Motor

Orange/Orange Motor

Capacitor

Bornier

Junction

Box

Green/Vert

120V~60Hz

Gray 4 speed

Black 3 speed

Red 2 speed

Blue 1 speed

Brown (neutral)

Lamp/Lampes

EN

La page charge ...

Fisher Paykel HP24ILTX1 Guide d'installation

Fisher Paykel HP24ILTX1 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents