Real Flame Berthoud C1460LP Le manuel du propriétaire

Marque: Real Flame

Modèle: Berthoud C1460LP

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Ce manuel convient également à

If the information in this manual

is not followed exactly, a ﬁ re or

explosion may result causing

property damage, personal injury

or loss of life.

Installation and service must be

performed by a qualiﬁ ed installer,

service agency or gas supplier.

Improper installation, adjustment,

alteration, service or maintenance

can cause injury or property

damage.

Read the installation, operation

and maintenance instructions

thoroughly before installing or

servicing this equipment.

Save these instructions for

future reference. If you are

assembling this unit for

someone else, give this manual

to him or her to read and save

for future reference.

! !

IMPORTANT

WARNING

SAVE THESE

INSTRUCTIONS

DANGER

If you smell gas:

1. Shut o gas to the appliance.

2. Extinguish any open ﬂ ame.

3. If odor continues, keep away from the appliance and

immediately call your gas supplier or ﬁ re department.

WARNING

Do not store or use gasoline or other ﬂ ammable

vapors and liquids in the vicinity of this or any

other appliance.

An LP-cylinder not connected for use should not

be stored in vicinity of this or any other appliance.

For outdoor use only. DO NOT use

for cooking. DO NOT use under any

overhead enclosure.

USC

For Technical Support Please Contact Real Flame® At: 1-800-654-1704

Lot: _______________

P.O. _______________

C1460LP Berthoud

Propane Fire Pit

Owner’s Manual

TABLE OF CONTENTS

Important Safety Information

Gas Dangers and Warnings

Parts List

Assembly Instructions

Pre-Use Instructions

Lighting Instructions

Spider and Insect Warning

Tips and Troubleshooting

Technical Parts List

DANGER

This appliance can produce carbon

monoxide which has no odor.

Using it in an enclosed space can kill you.

Never use this appliance in an enclosed

space such as a camper, tent, car or home.

CARBON MONOXIDE HAZARD

Product Name

Berthoud LP Fire Pit

Model No.

C1460LP

Rated Heat Output

50,000 btu/hr

Type of Gas

Propane (LP)

Gas Supply

20 lb LP-Gas Cylinder

SPECIFICATIONS

Care and Cleaning 11

Warranty 16

IMPORTANT SAFETY INFORMATION

Installation notes

General Warnings

• Minimum Clearance from unit to combustible materials:

48” (121.9 cm) from all sides and back. Do not place this ﬁre table under any overhead structure or

vegetation. Do not place on or above combustible surfaces.

• Save these instructions for future reference. If you are assembling this unit for someone else, give this

manual to them to read and save for future reference.

• If the information in this manual is not followed exactly, a ﬁre or explosion may result causing property

damage, personal injury, or death.

• Installation and service must be performed by a qualiﬁed service agency or gas supplier. Real Flame

recommends using professionals who are certiﬁed in the U.S. by the National Fireplace Institute® (NFI)

as NFI Gas Specialists.

• The normal LP inlet pressure for this appliance is 11.0” W.C. (2.74 kPa), maximum inlet pressure is 13.0”

W.C. (3.23 kPa), minimum inlet pressure is 8” W.C. (1.99 kPa).

• If this ﬁre table has been converted to natural gas, the normal inlet pressure for this appliance is 7.0”

W.C. (1.74 kPa), maximum inlet pressure is 10.5” W.C. (2.61kPa), minimum inlet pressure is 3.5” W.C.

(0.87 kPa).

• Do not remove the feet from the ﬁre table.

• Do not place the ﬁre table on anything that blocks or seals the gap between the table and the ground.

• Do not permanently secure the ﬁre table in any way or to any surfaces.

• Do not bury the hose. You must be able to visually inspect the hose for damage before each use.

• Do not coil or hide the hose under the ﬁre table. The hose could be damaged if it touches hot

surfaces.

• Children and adults should be alerted to the hazards of high surface temperatures and should stay

away to avoid burns or clothing ignition.

•

the appliance.

•

operating the appliance.

•

may be required as necessary. It is imperative that the control compartment, burners, and

circulating air passageways of the appliance are kept clean.

• Do not store or use gasoline or other ﬂammable vapors or liquids within 25 feet ( 7.62 m) of this or

any other appliance.

• Do not store combustible materials in the ﬁre table enclosure. This includes LP tanks. If the ﬁre table

is designed to use a hidden LP tank, the LP tank should be properly secured in the designated tank

holder under the table. Do not store extra LP tanks under the ﬁre table.

• Be sure to protect the hose and its components from any hot surfaces. It is dangerous to allow the

hose to come into contact with any hot surface.

• If using your ﬁre table with a LP tank, the tank should never be operated or stored on its side or up-

side-down.

IMPORTANT SAFETY INFORMATION

General Warnings (Cont.)

Set-Up Warnings

In-Use Warnings

• Keep all parts of the ﬁre table clean including the burner and hose assembly. For more information on

cleaning your ﬁre table please refer to the Care and Cleaning section of this manual.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁed service

technician to inspect the appliance and to replace any part of the control system and any gas control

that has been under water.

• Do not use this ﬁre table for cooking.

• Do not pour water into the ﬁre table.

• Do not attempt to move or store this ﬁre table until all parts are cool.

•

• Any alteration of this outdoor ﬁre table that is not speciﬁcally directed in the owner’s manual will void

the manufacturer’s warranty. This includes the use of unapproved ﬁller materials.

• Prior to each operation, check the hose assembly for evidence of excessive abrasion, wear or damage.

Use a hand-held mirror, if necessary, to see hose sections located below the unit.

• If the hose assembly is damaged, cracked, or cut, it must be replaced before using the ﬁre table.

The hose assembly must be replaced with a hose assembly speciﬁed by Real Flame. Please call us at

1-800-654-1704 for assistance.

• Place the hose out of the pathways where people may trip over it. Do not place the hose in areas

where it may be accidentally damaged.

• Before each use, examine the burner and its components for dirt and debris. If cleaning is required,

use a pipe brush and soapy water solution. Also examine the area around the burner. Any dirt or

foreign material such as spider webs, nests, leaves, etc., should be removed. If it is evident that the

burner is damaged, the ﬁre table must not be used, and the burner assembly must be replaced. Please

contact Real Flame at 1-800-654-1704 for support.

• Do not burn solid fuels such as wood, charcoal briquettes, lump charcoal, manufactured logs, drift

wood, trash, leaves, paper, cardboard, plywood, painted, stained or pressure-treated wood and other

materials in this ﬁre table.

• NEVER LEAVE this ﬁre table unattended when in use.

• The use of alcohol, prescription or non-prescription drugs may impair your ability to safely operate

this ﬁre table.

• Always use in accordance with all applicable local, state and national codes. Contact your local ﬁre

department for details on outdoor burning.

• Do not use in windy conditions. W

inds above 10 mph may cause the ﬂame to extinguish.

• Some surfaces of this ﬁre table may become hot during use. Be careful and do not touch surfaces

until the unit has cooled.

GAS DANGERS AND WARNINGS

LP Gas Warnings

LP Characteristics

• LP gas is ﬂammable, explosive under pressure, heavier than air and settles in pools in low areas.

Pooled gas may ignite causing a ﬁre or explosion which could cause property damage, injury or death.

• In its natural state, propane has no odor. For your safety, a scent has been added.

• Contact with propane could burn your skin.

LP Tank Information

• LP gas cylinders should be ﬁlled only by a certiﬁed LP gas dealer.

• Never use a propane cylinder with a damaged body, valve, collar or footing.

• Dented or rusted propane cylinders may be hazardous and should be checked by your propane gas

supplier.

• The LP gas supply tank must be constructed and marked in accordance with the Speciﬁcations for

LP gas tanks of the U.S. Department of Transportation (DOT) or the National Standard of Canada,

CAN/CSA-B339, LP gas tanks, Spheres and Tubes for the Transportation of Dangerous Goods; and

Commission.

• LP gas tanks must be arranged for vapor withdrawal.

• LP gas tanks must have a listed overﬁlling prevention device (OPD) and a QCCI or Type I (CGA810) LP

gas tank connection.

•

Cylinder Valve Outlet and Inlet Connection, ANSI/CGA-V-1-1977, CSA B96.

• Never attempt to attach this appliance to the self-contained LP gas system of a camper trailer, motor

home or house.

• Hand-turn the manual gas control valve on your LP tank. Never use tools. If the valve will not turn by

hand, do not try to repair it. Call a certiﬁed gas technician.

• The use of force or any attempt at amateur repair may cause a ﬁre or explosion.

LP Tank Storage and Safety

• Cylinders must be stored upright and outdoors in a well-ventilated area out of reach of children.

• Never store an LP cylinder in any enclosed area such as a shed or garage. Leaking gas could build up

in these areas and may result in an explosion.

• Do not store LP gas tanks near any source of ﬂame or ignition.

• Never store your LP gas tank in direct sunlight or where temperatures can reach 125°F or higher.

• Never keep a ﬁlled LP gas tank in a hot car or car trunk. Heat will cause the gas pressure to increase,

which may open the relief valve and allow gas to escape.

• Place dust cap on valve outlet whenever the LP gas tank is not in use. Install only the type of dust cap

on the LP gas tank valve outlet that is provided with the LP gas tank valve. Other types of caps or

plugs may result in leakage of propane.

• The LP gas tank should not be dropped or handled roughly.

LP gas is ﬂammable and hazardous if handled improperly. Become aware of its characteristics before

using any LP gas product. Failure to understand and follow these warnings or any directions and

warnings provided by your LP supplier may result in property damage, injury or death.

DANGER

A LP cylinder should never be placed on its side. Doing so may cause liquid propane to leak. This

could cause a fast build-up of propane gas and could lead to property damage, injury or death.

In-Use Warnings (Cont.)

• Do not attempt to disconnect the gas supply from the ﬁre table when the unit is in use.

• Do not sit on the ﬁre table.

PARTS LIST

Fire Table N/A 1

Lava Rocks 05633404 1 Box

AAA Battery N/A 1

Protective Cover 14600001 1

Tank Seat 05600005 1

Conversion Kit 00023105G 1

Lid 15100101 1

ASSEMBLY INSTRUCTIONS

1.) Install the AAA battery as shown in the diagram below

2.) Place lava rock ﬁller by hand. Do not dump the bag into the burner

area, or directly onto the burner to avoid clogging the burner with dust. Position the ﬁller

material across the burn area to a level 1” above the burner. Make sure that you do not

block the igniter housing with ﬁller to ensure proper ignition and operation.

If using glass ﬁller Real Flame suggests placing a layer of lava rock down ﬁrst around the

burner then adding glass on top of that to improve airﬂow to the burner.

Lava Rock and Glass Filler Warning

1. Do not overﬁll the burner area with rock or glass ﬁller; use only the speciﬁed amount. The depth

of the ﬁller should not be more than one inch above the burner tube. Only Real Flame ﬁller products

have been certiﬁed and tested for safe use with this Real Flame ﬁre table. Using other ﬁller material

may result in increased popping and cracking or increased carbon monoxide emissions.

2. Do not light or use this ﬁre table if the ﬁller is wet. Ensure ﬁller is completely dry before lighting.

Intense heat can cause wet ﬁller to explode and hit someone causing injury.

3. Keep away from the ﬁre table for at least 20 minutes during initial start-up as ﬁller could retain

moisture from manufacturing and shipping.

Igniter housing

ASSEMBLY INSTRUCTIONS

4.) Connect the LP Gas Tank

Before connection, be sure there is no debris caught in the

collar of the gas cylinder, the regulator valve or the burner

and burner ports.

Connect the gas line to the tank by turning the connection

knob clockwise. Hand tighten only.

To disconnect the LP tank, make sure the valve on the LP

gas tank is completely closed.

Disconnect the connection knob by turning it counter-

clockwise until it is detached from the valve.

WARNING

Place the LP tank 60” away from the ﬁre table and

locate the hose away from pathways or places where

it could become damaged.

Watch your step while moving between the tank and

the ﬁre table. Be careful not to trip on the hose.

3.) Place the tank seat on the ground and place a 20 lb. propane tank into the

designated area in the center. Once the tank is level and steady, tighten down the

screw on the side of the tank seat to secure the tank in place.

60”

PRE-USE INSTRUCTIONS

WARNING

Before using this ﬁre table, make sure you have read, understand, and are following all information

provided in this manual. Failure to follow these instructions could cause property damage, serious

injury or death.

Make a leak check solution by mixing one part dish-washing soap with three parts water in a spray

bottle.

Make sure that the control knob on the ﬁre table is in the OFF position, then connect your ﬁre

table to a LP gas tank and turn the tank’s valve on.

Spray leak solution on the valve connections, paying particular attention to the areas indicated in

the diagrams below by arrows.

If bubbles appear, close the tank valve, disconnect the tank, and inspect all connections making

sure threads are clear of debris. Reconnect the LP tank and re-test. If you continue to see bubbles,

If no bubbles appear after one minute, wipe away excess leak solution and proceed to the next

step.

Checking for Leaks

Pay close attention to the areas indicated by the arrows

LIGHTING INSTRUCTIONS

Using the Igniter

1. Read and understand all operating instructions before lighting.

2. Before beginning, make sure the control knob is in the OFF position.

3. Connect your propane cylinder (see previous pages).

4. Slowly open the valve on your LP cylinder.

5. Prepare to ignite your ﬁre table by placing one hand on the control

knob and one hand on the ignition button(as seen in diagram on the

right). DO NOT lean over any part of the burner, and verify that the

area around the burner is free of hazards.

6. Push and hold the igniter, you should hear a clicking sound.

7. While holding the igniter depressed with one hand, use your other

hand to push in and turn the control knob to the LIGHT position.

8. Once the burner ignites, release the igniter button, but continue to keep the control knob

pushed in for 15-30 seconds.

9. WARNING: If ignition does not occur in 15 seconds, turn the control knob to the “OFF”

the ﬁre table and wait at least ﬁve minutes until the gas has cleared to repeat the lighting

procedure. Failure to do so could result in a large ﬂashback of pooled gas, causing property

damage or injury.

10. After successfully lighting the table, release the control knob and turn it to the LOW setting.

Observe the ﬂame and make sure that all the burn ports are lit.

11. Adjust the ﬂame to the desired height using the control knob.

1. Turn the control knob to the OFF position.

Push Control

Knob In

Flame Height

8-14”

20.3-35.5 cm

CARE AND CLEANING

Inspecting Your Fire Table

General Care and Cleaning

Storage

Your ﬁre table should be inspected regularly to ensure that it is safe to use and to extend the life

of its parts.

To inspect your ﬁre table follow these steps.

1. Make sure all parts are securely fastened in place. If a part moves when touched, check its

connection points to see if they are loose.

2. Check all connections for leaks using the leak check method described in the “Check for Leaks”

section of this manual.

3. Check the ignition system by pushing the igniter button and verifying that a spark is being

generated in the igniter housing.

4. Visually check all components for any signs of damage, rust, or excessive wear.

5. If damage or leaks of any kind are found, DO NOT operate the ﬁre table until the proper repairs

have been made.

After repeated use, a slight discoloration or weathering of the ﬁre table ﬁnish may occur. Your ﬁre

table should be cleaned regularly to ensure safe use and extend its life.

General Cleaning

Make a cleaning solution using a mild soap mixed with water. Use a soft cloth to wipe down

exterior surfaces and rinse with clean water. Never use oven cleaners or abrasive solvents as these

will damage the ﬁre table.

Burner

The burner should be kept clean to ensure proper operation. Clogged burn ports may be cleared

with a paper clip or pin. Debris in the burner can be cleaned using compressed air or a pipe brush.

Soot

with water and mild soap.

and away from children.

2. Secure all loose ﬁller material or parts.

3. Remove the battery from the ignition box.

4. Cover your ﬁre table when it will not be in use. Covering the table will help to protect the

internal components from dirt and debris, prevent water from pooling on the surfaces and

prevent the ﬁnish from fading and discoloring.

5. Store the ﬁre table in a cool, dry location away from children and pets.

WARNING

DO NOT inspect, clean, move or store your ﬁre table until the ﬂames are COMPLETELY out and all

parts are cool to the touch.

DO NOT tamper with this appliance. This is dangerous and will void the warranty.

Repairs and modiﬁcations must be approved by Real Flame and completed by a professional gas

technician.

This ﬁre table has been tested and certiﬁed by a third party certiﬁcation agency based on its

speciﬁc and unique parts. Installing any other parts will void both the certiﬁcation and the

warranty. For approved replacement parts, contact Real Flame at: 1-800-654-1704

SPIDER AND INSECT WARNING

Spiders or other insects may build webs or nests in your ﬁre table burner tube which can obstruct or

block the ﬂow of gas.

Some of the gas may back up in the burn tube and cause a ﬂashback (a ﬁre in the burn tube or

underneath the ﬁre table) which could result in personal injury or property damage. Check and clean the

burn tube periodically using a pipe cleaner brush (as shown below) available at any hardware store.

Example of a typical burn tube

Your exact burner may vary

Burn Tube

Insect Nest

Air Intake

Run Pipe Cleaner

through burn tube

Possible Spider

Nest or Debris

Example of pipe

cleaning brush available

at local hardware stores.

TIPS AND TROUBLESHOOTING

If the ﬁre table will not ignite

CORRECT INCORRECT

If the ﬁre table will not stay lit

1. Make sure that the battery is not dead and that it is installed correctly, with the

positive (+) side facing out.

Make sure that the igniter housing is unobstructed. Clear away any ﬁller material or debris on the

housing and make sure there is nothing between the igniter pin and the thermocouple.

If the ignition system is working correctly, you should hear a clicking sound while the

igniter button is pushed and you should see a spark inside the igniter housing. If you do

not see the spark or hear a clicking sound, please check the following.

If the ﬁre table lights, but will not stay lit, or remains lit only for a brief time, please check the

following.

2. If you still do not hear a clicking sound or see a spark in the

igniter housing, look under the ﬁre table and make sure that the

electrode wire is correctly inserted into the back of the electronic

ignition box. While inspecting the electrode wire, make sure that

it is not cut or broken in any place. If the wire has been damaged

contact Real Flame at 1-800-654-1704 for a replacement.

3.) If you hear clicking but cannot see a spark in the igniter

housing, look under the table. Check between the electrode

wire connection at the back of the electronic ignition and the

connection point at the burn pan. If you see a spark anywhere

under the table, look for damage to the wire or an incomplete

connection at that point. If the wire has been damaged contact

Real Flame at 1-800-654-1704 for a replacement.

Igniter Housing

Burner Tube

Do not block

opening

TIPS AND TROUBLESHOOTING

If the ﬁre table will not stay lit (Continued)

Other Common Problems

Make sure that the thermocouple and electrode

are correctly positioned.

The igniter housing has been removed from the

illustration to the right to better show positioning;

however, you should be able to look through

the openings of the igniter housing to verify this

without removing it.

Thermocouple - The thermocouple tip should

be located close to the burner, aligned with a

burn port so that ﬂames contact it directly. Make

sure the ﬂames are making contact with the

thermocouple tip.

Electrode - The electrode is where the spark is

generated to ignite your ﬁre table. Make sure that

you can see this sparking when the igniter button

is pushed.

Damaged Thermocouple

If the igniter housing and the thermocouple tip are clear of debris and the ﬂame is clearly contacting

the tip of the thermocouple, but the ﬁre table will still not stay lit, the thermocouple may be

damaged. Look beneath the table and ﬁnd the copper thermocouple wire coming out of the back of

the valve. Examine the length of it for any signs of damage. Sharp bends, kinks or damage can cause

the thermocouple to not function correctly. If you ﬁnd damage to the thermocouple contact Real

Flame at 1-800-654-1704 for a replacement.

Clogged or Obstructed Burner

It is common for bugs, especially spiders, to make webs or nests inside of burner tubes. If it seems

like you are getting low or no gas ﬂow, visually check all openings in the burner for signs of clogs. If

you see anything clogging the burner try using compressed air to remove the debris.

Out of Gas

Be sure that your tank is not empty. Low tanks can result in lower ﬂames.

Cold Temperatures

Cold temperatures outside may result in lower tank pressures causing the ﬂames to be lower. Do not

use your ﬁre table in extreme temperature conditions. Allow the temperature of your tank to rise

and as the pressure in the tank increases the ﬂame size will increase

. NEVER heat your tank; allow it

to warm up naturally.

High Winds

Your ﬁre table is designed to operate in winds up to 10 mph. High winds may cause the ﬂame to

blow out. Do not operate your ﬁre table in high wind conditions.

Thermocouple

Make sure ﬂame

is contacting this.

Electrode

You should see this

spark when pushing

the igniter button.

Igniter Housing

removed for visibility

If you continue to have problems with your ﬁre table please

contact Real Flame customer service at : 1-800-654-1704

TECHNICAL PARTS LIST

Burn Tube

100140005

Igniter Housing

100280026

Igniter Electrode

100280025

Electronic Ignition

100240000

LP Hose and Regulator

0562LP10

Thermocouple

100300004

Control Knob

10040U000

Valve

100130002

Burn Pan

N/A

Natural Gas Conversion Kit

00023105G

Lid

15100101

Short Side Panel

N/A

Short Side Panel

N/A

Long Side Panel

N/A

Long Side Panel

N/A

Adjustable Feet

14600002

Hose Guide

100060001

Top

N/A

Bellows (CSST)

100230008

LP Oriﬁce Spud

100270011

WARRANTY AND RETURN POLICIES

Warranty

Real Flame® Company warrants Real Flame ﬁreplaces and accessories to be free from defects in parts

under normal use and service for a period of 1 year from the date of purchase and defective from ﬁnish

issues for a period of 1 year from the date of purchase. In the event of such defects Real Flame will, at

its option, replace the defective product or refund the purchase price. The foregoing is the exclusive

remedy and Real Flame disclaims all other warranties, including any implied warranty of merchantability

or ﬁtness for a particular purpose. In addition, Real Flame will not be responsible for consequential

damages in excess of the purchase price of the product on which such liability is based.

Return Policy

You may return your purchase within 90 days of receipt. No refunds will be issued for incomplete or

unauthorized returns. All returned products must be 100% complete, adequately packaged in original

packaging and in resalable condition. Products that have been assembled or modiﬁed will not be eligible

for return. All items must be returned in their entirety, meaning all items included must be returned

together. No returns or exchanges on discontinued items. Please begin the return process by contacting

the store or company where you bought your Real Flame item.

Replacement Parts

In the event that an item has been lost or damaged, either by the manufacturer or in shipping, you

may request a replacement. Replacement parts are not available for all units and only given at Real

Flame’s discretion. We will assess any damage and ﬁnd a solution, which could include shipping you a

replacement. No replacements are available for discontinued items or repackaged (open box) products.

Please call Real Flame Customer Service at 800-654-

1704 for replacement parts before returning the

damaged item. Please have the following information (which can be found in your instruction manual)

ready before you call Customer Service.

• Model Number of Item

• 4-8 digit Part Number

• Lot Code Number

• Shipping Address

• A picture of the damaged item may be requested. Pictures should be sent to custserv@realﬂame.com

Incorrect Order Received

If you received something other than what you ordered, please contact Real Flame Customer Service at

800-654-1704 within 48 hours of receiving the item. Please refer to www.Realﬂame.com for our complete

return guidelines and policies.

Please refer to www.Realﬂame.com for our complete return guidelines and policies.

Real Flame®

7800 Northwestern Ave.

Racine, WI 53406

Customer Service: 1-800-654-1704 in USA

Service à la clientèle: 1-800-363-6443 in Canada

custserv@realﬂame.com

USC

Pour le support technique S’il vous plaît nous contacter: 1-800-654-1704

C1460LP Berthoud

Lot: _______________

P.O. _______________

MANUEL DU PROPRIÉTAIRE DE TABLE-FOYER

AVERTISSEMENT

DANGER

Pour usage extérieur uniquement.

Si vous sentez du gaz:

• Arrêtez le gaz vers l’appareil.

• Si l’odeur persiste, éloignez-

vous de l’appareil et appelez

immédiatement votre fournisseur de

gaz ou votre service des incendies.

AVERTISSEMENT

proximité de cet appareil ou de tout autre appareil.

Une bonbonne de gaz propane liquide (GPL) non connecté pour

l’utilisation ne doit pas être entreposée à proximité de cet appareil

ou d’un autre appareil.

L’installation, le réglage, l’altération, le service ou l’entretien

inadéquat peuvent causer des blessures ou des dommages

matériels.

Lisez attentivement les instructions d’installation, d’utilisation et

d’entretien avant d’installer ou d’entretenir cet équipement.

TABLE DES MATIÈRES

Informations importantes sur la sécurité

Avertissements concernant le gaz

Liste des pièces

Instructions d’assemblage

Instructions d’allumage

Entretien et nettoyage

Conseils et dépannage

Garantie

DANGER

Nom du produit

Berthoud Table-foyer

No. du modèle

C1460LP

Puissance Nominale

50,000 btu/hr

Type de gaz

Propane (GPL)

Approvisionnement en Gaz

Bonbonne de GPL de 20 lb

CARACTÉRISTIQUES

Avertissement concernant les araignées et les insectes

RISQUE DE MONOXYDE DE CARBONE

Cet appareil peut produire du monoxyde de

carbone qui n’a pas d’odeur.

L’utiliser dans un espace fermé peut vous tuer.

Ne jamais utiliser cet appareil dans un espace

fermé comme une autocaravane, une tente, une

voiture ou à l’intérieur de la maison.

Instructions avant l’utilisation 9

Liste des pièces techniques 15

Notes d’installation

Avertissements généraux

• Distance minimale de l’unité aux matériaux combustibles :

121,9 cm (48 po) de tous les côtés et de l’arrière. Ne placez pas cette table-foyer sous aucune

structure suspendue ou végétation. Ne la placez pas sur ou au-dessus des surfaces combustibles.

• Conservez ces instructions pour référence ultérieure. Si vous assemblez cette unité pour quelqu’un

d’autre, donnez-leur ce manuel pour lire et conserver pour référence ultérieure.

• Si les informations contenues dans ce manuel ne sont pas suivies exactement, un incendie ou une

explosion peut entraîner des dommages matériels, des blessures corporelles ou la mort.

•

de gaz. Real Flame recommande d’utiliser des professionnels certiﬁés aux États-Unis par le National

Fireplace Institute® (NFI) en tant que Spécialistes NFI du Gaz.

• La pression d’entrée GPL normale pour cet appareil est de 11,0 po W.C. (2,74 kPa), la pression d’entrée

maximale est de 13,0 po W.C. (3,23 kPa), la pression d’entrée minimale est de 8 po W.C. (1,99 kPa).

• Si cette table-foyer a été convertie au gaz naturel, la pression d’entrée normale pour cet appareil

est de 7,0 po W.C. (1,74 kPa), la pression d’entrée maximale est de 10,5 po W.C. (2.61kPa), la pression

d’entrée minimale est de 3,5 po W.C. (0,87 kPa).

• Ne retirez pas les pieds de la table-foyer.

• Ne placez pas la table-foyer sur tout ce qui bloque ou scelle l’espace entre le foyer et le sol. Ne ﬁxez

pas en permanence la table-foyer de quelque manière que ce soit ou à aucune surface.

• N’enterrez pas le tuyau. Vous devez pouvoir inspecter visuellement le tuyau avant toute utilisation.

• N’enroulez pas ou ne cachez pas le tuyau sous la table-foyer. Le tuyau pourrait être endommagé s’il

touche des surfaces chaudes.

• Les enfants et les adultes doivent être informés des risques de températures de surface élevées et

doivent rester éloignés pour éviter les brûlures ou que leurs vêtements prennent feu.

• Les jeunes enfants devraient être soigneusement surveillés dans la zone de la table-foyer.

•

placés sur ou à proximité de l’appareil.

• Toute protection ou autre dispositif de protection retiré pour l’entretien de la table-foyer doit être

remplacé avant d’utiliser l’appareil.

•

nettoyage plus fréquent peut être nécessaire. Il est impératif que le compartiment de commande,

les brûleurs et les passages de circulation d’air de l’appareil soient maintenus propres.

• N’entreposez pas ou n’utilisez pas d’essence ou d’autres vapeurs ou liquides inﬂammables à moins de

7,62 m (25 pi) de cet appareil ou de tout autre appareil.

• Ne rangez pas de matériaux combustibles dans le boîtier de la table-foyer. Cela comprend les

bonbonnes de GPL. Si la table-foyer est conçue pour utiliser une bonbonne de GPL dissimulée, la

bonbonne de GPL doit être correctement ﬁxée dans le porte-bonbonne désigné sous la table-foyer.

N’entreposez-pas de bonbonnes de GPL supplémentaires sous la table-foyer.

• Assurez-vous de protéger le tuyau et ses composants de toutes surfaces chaudes. Il est dangereux de

permettre au tuyau d’entrer en contact avec une surface chaude.

• Si vous utilisez votre table-foyer avec une bonbonne de GPL, la bonbonne ne doit jamais être utilisée

sur le côté ou à l’envers.

INFORMATIONS IMPORTANTES SUR LA SÉCURITÉ

Avertissements généraux (suite)

Avertissements d’installation

Avertissements lors de l’utilisation

• Conservez toutes les parties de la table-foyer propres, y compris le brûleur et l’assemblage du tuyau.

Pour plus d’informations sur le nettoyage de votre table-foyer, consultez la section Entretien et

nettoyage de ce manuel.

• N’utilisez pas cet appareil si une partie a été submergée. Appelez immédiatement un technicien de

service qualiﬁé pour inspecter l’appareil et remplacer toute partie du système de contrôle et toute

commande de gaz qui a été sous l’eau.

• N’utilisez pas cette table-foyer pour la cuisson.

• Ne versez pas d’eau dans la table-foyer.

• N’essayez pas de déplacer ou de ranger cette la table-foyer jusqu’à ce que toutes les pièces soient froides.

• Coupez toujours l’alimentation en gaz à la source et débranchez le tuyau lorsque la table-foyer n’est pas utilisée.

• Toute modiﬁcation de cette table-foyer extérieure qui n’est pas directement spéciﬁée dans le

manuel du propriétaire annulera la garantie du fabricant. Cela comprend l’utilisation de matériaux de

remplissage non approuvés.

• Avant chaque fonctionnement, vériﬁez l’assemblage du tuyau pour vous assurer qu’il n’y a pas trop

d’abrasion, d’usure ou de dommage. Utilisez un miroir portatif, si nécessaire, pour voir les sections de

tuyau situées sous l’appareil.

• Si le tuyau ﬂexible e

st endommagé, ﬁssuré ou coupé, il doit être remplacé avant d’utiliser la table-

foyer. L’ensemble de tuyau doit être remplacé par un ensemble de tuyau spéciﬁé par Real Flame.

Veuillez nous appeler au 1-800-654-1704 pour obtenir de l’assistance.

• Placez le tuyau hors des sentiers où les gens peuvent trébucher dessus. Ne placez pas le tuyau dans

les endroits où il risque d’être endommagé accidentellement.

• Avant chaque utilisation, examinez le brûleur et ses composants pour détecter la saleté et les

débris. Si le nettoyage est nécessaire, utilisez une brosse à tuyau et une solution d’eau savonneuse.

Examinez également la zone autour du brûleur. Toutes saletés ou matières étrangères telle que les

toiles d’araignées, les nids, les feuilles, etc., doivent être enlevées. S’il est évident que le brûleur est

endommagé, la table-foyer ne doit pas être utilisée et le brûleur doit être remplacé. Veuillez contacter

Real Flame au 1-800-654-1704 pour obtenir de l’assistance.

• Ne brûlez pas de combustibles solides comme le bois, les briquettes de charbon de bois, le

charbon de bois, les bûches fabriquées, le bois ﬂotté, les déchets, les feuilles, le papier, le carton, le

contreplaqué, le bois peint ou traité.

• NE LAISSEZ JAMAIS cette table-foyer sans surveillance lorsqu’elle est en cours d’utilisation.

• L’utilisation d’alcool, de médicaments sur ordonnance ou en vente libre peut nuire à votre capacité à

utiliser cette table-foyer en toute sécurité.

• Utilisez toujours conformément à tous les codes locaux, provinciaux et nationaux applicables.

Contactez votre service d’incendie local pour plus de détails concernant les feux extérieurs.

• Ne l’utilisez pas dans des conditions venteuses. L

es vents supérieurs à 10 km/h peuvent éteindre la ﬂamme.

• Certaines surfaces de cette table-foyer peuvent devenir chaudes pendant l’utilisation. Faites attention

et ne touchez pas les surfaces de l’appareil jusqu’à ce qu’elles soient refroidies.

INFORMATIONS IMPORTANTES SUR LA SÉCURITÉ

La page est en cours de chargement...

Real Flame Berthoud C1460LP Le manuel du propriétaire

Marque: Real Flame

Modèle: Berthoud C1460LP

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Real Flame Berthoud C1460LP Owner's manual
español: Real Flame Berthoud C1460LP El manual del propietario

Documents connexes

Autres documents

Elementi ONB016 Manuel utilisateur