GE Profile P2S975WEMWW Guide d'installation

TOOLS YOU WILL NEED

1

MATERIALS YOU MAY NEED

31-10641-1 03-07 JR

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

In Canada, call 1.800.361.3400 or Visit our Website at: www.geappliances.ca

Installation

Self-Cleaning Dual Fuel

Instructions

Slide-In Range

P2S975

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

•

IMPORTANT — Save these

instructions for local inspector’s use.

•

IMPORTANT — Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these

instructions for future reference.

• Product failure due to improper installation

is not covered under the Warranty.

WARNING — This appliance must

be properly grounded.

• Proper installation is the responsibility

of the installer and product failure due

to improper installation is NOT covered

under warranty.

IN THE COMMONWEALTH OF

MASSACHUSETTS:

• This product must be installed by a

licensed plumber or gas fitter.

• When using ball-type gas shut-off valves,

they shall be the T-handle type.

• A flexible gas connector, when used, must

not exceed 3 feet.

PARTS INCLUDED

Anti-Tip Bracket

Anchor Sleeves

Lag Bolts

(For Concrete Floors Only)

Shut Off Valve

Pipe Fittings

CSA-Approved Flexible Gas Line

3/8″ Min. ID, 1/2″ NPT Connection,

3-foot Maximum Length (Massachusetts only)

Joint Sealant

Wrench or Pliers

(for 1-7/16” Nut)

Level

1/4” Nut Driver

Safety Glasses

Drill

Tape Measure

Screws

Rear Filler

2 Screws

Phillips Head

Screwdriver

Pipe Wrench

Flat-blade

Screwdriver

2

Installation Instructions

FOR YOUR SAFETY:

WARNING — If the information

in this manual is not followed exactly, a fire,

explosion or gas leak may result causing

property damage, personal injury or death.

Do not store or use gasoline or other

flammable vapors and liquids in the vicinity

of this or any other appliance!

WHAT TO DO IF YOU

SMELL GAS:

• Do not try to light any appliance. Do not

touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier,

call the fire department.

Installation and service must be performed

by a qualified installer, service agency or

the gas supplier.

IMPORTANT SAFETY INSTRUCTIONS

This range has been design certified by

UNDERWRITERS LABORATORIES for use in

the United States and Canada. You’ll find

safety precautions in your Owner’s Manual.

Read them carefully.

• Installation of this range must conform with

local codes or in the absence of local codes

with the National Fuel Gas Code, ANSI

Z223.1–Latest edition.

• Be sure your range is installed properly by

a qualified installer or service technician.

• To eliminate reaching over surface burners,

cabinet storage above burner should be

avoided.

• Do not install the unit near an outside door

or where a draft may affect its use.

3

Installation Instructions

ANTI-TIP DEVICE

WARNING — To reduce the risk

of tipping, the appliance must be secured by

properly installed Anti-Tip bracket packed

with this appliance.

If the Anti-Tip device supplied with the range

does not fit this application, use the universal

Anti-Tip device WB2X7909. Skip Steps 4, 19

and 21.

To check if the bracket is installed and

engaged properly, carefully tip the range

forward. The anti-tip bracket should engage

and prevent the range from tipping over.

WARNING —

• All ranges can tip

• Injury to persons could result

• Install Anti-Tip bracket packed

with range

• See Installation Instructions

If you pull the range out and away from the

wall for any reason, make sure the Anti-Tip

bracket is engaged when the range is pushed

back against the wall.

ELECTRICAL REQUIREMENTS

This appliance must be supplied with the

proper voltage and frequency and connected

to an individual, properly grounded branch

circuit, protected by a circuit breaker or fuse

having a recommended amperage rating per

the table below.

BREAKER OR FUSE SIZE

240V 40 Amps

208V 40 Amps

NOTE: Check Local Codes for required

breaker size.

Rating plate is located above the storage

drawer below the oven frame.

We recommend you have the electrical wiring

and hookup of your range connected by a

qualified electrician. After installation, have

the electrician show you where your main

range disconnect is located.

Check with your local utilities for electrical

codes which apply in your area. Failure to

wire your range according to governing

codes could result in a hazardous condition.

If there are no codes, your range must be

wired and fused to meet the requirements of

the National Electrical Code, ANSI/NFPA No.

70–Latest edition. You can get a copy by

writing:

National Fire Protection Association

Batterymarch Park

Quincy, MA 02269

Effective January 1, 1996, the National

Electrical Code requires that new, but not

existing, construction utilize a four-conductor

connection to an electric range. When installing

an electric range in new construction, a mobile

home, recreational vehicle or an area where

local codes prohibit grounding through the

neutral conductor, follow the instructions in the

section on NEW CONSTRUCTION AND FOUR-

CONDUCTOR BRANCH CIRCUIT

CONNECTION.

In Canada your range must be wired and

fused to meet the requirements of the

Canadian Electrical Code.

You must use a three-wire, single-phase

A.C. 208Y/120 Volt or 240/120 Volt, 60 hertz

electrical system.

FOR YOUR SAFETY:

WARNING — For personal safety,

remove house fuse or open circuit breaker

before beginning installation. Failure to do so

could result in serious injury or even death.

All rough-in and spacing dimensions must be

met for safe use of your range. Electricity to

the range can be disconnected at the outlet

without moving the range if the outlet is in

the preferred location (remove lower drawer).

To reduce the risk of burns or fire when

reaching over hot surface elements, cabinet

storage space above the cooktop should be

avoided. If cabinet storage space is to be

provided above the cooktop, the risk can

be reduced by installing a range hood that

protrudes at least 5” beyond the front of the

cabinets. Cabinets installed above a cooktop

must be no deeper than 13”.

Be sure your appliance is properly installed

and grounded by a qualified technician.

Rating

plate location

4

Installation Instructions

INSPECT INSTALLATION

LOCATION

Refer to alternate construction section for

the following non-standard installations.

Counter opening extends to the wall:

Maintop Filler (supplied with the

range.) (See page 17 for Installation

Instructions) or

Backguard (Kit JXS32XX or JXS37XX).

Counter height greater than 36-3/4″:

Lower Trim Slide-In (Kit JXS56XX).

One side is not enclosed by a cabinet:

Bodyside (Kit JXS77XX).

Island Installation:

To provide an optimum installation, the

top surface of the countertop must be

level and flat (lie on the same plane)

around the 3 sides that are adjacent to

range cooktop. Proper adjustments to

make the top flat should be made or

gaps between the countertop and

range cooktop may occur. Forcing the

cooktop to fit may cause excessive

gaps.

To obtain Kits:

a. Visit GE Web Site (See page 1)

b. Call GE Answer Center (See page 1)

c. Contact Dealer

D

C

B

A

1

PRE-INSTALLATION CHECKLIST

MOVE RANGE INDOORS IN

FRONT OF CABINET OPENING

Do not use hand trucks when moving the

unpackaged range.

2

PROTECT THE KITCHEN

FLOOR

Flatten and place a piece of the shipping

carton in front of the installation location to

protect the flooring.

3

CAREFULLY, TILT RANGE TO

ACCESS RANGE LEVELING

LEGS

Use an adjustable wrench to screw leveling

legs out so that support flanges clear top of

countertop.

4

ADJUST

5

Installation Instructions

REMOVE THE DOOR IF

NECESSARY

(cont.)

LIFT OFF DOOR

Lift door up and out until the hinge arms

clear the slots.

DO NOT LIFT THE DOOR BY THE HANDLE.

NOTE: The oven door is very heavy. Be sure

you have a firm grip before lifting the oven

door off the hinges. Use caution once the

door is removed. Do not lay the door on its

handle. This could cause dents or scratches.

C

5

Hinge clears slot

REMOVE THE DOOR IF

NECESSARY

Door removal is not a requirement for

installation of the product, but is an added

convenience. To remove the door:

UNLOCK HINGES

Push both hinge locks down toward the

door frame, to the unlocked position.

This may require a flat blade screwdriver.

POSITION DOOR

Place hands on both sides of the door, and

close the oven door to the removal position.

This is half way between the broil stop and

fully closed.

B

A

5

REMOVE PACKING

MATERIALS

Also remove labels on door, plastic on trim

and panel and all tape around the range.

6

REMOVE STORAGE DRAWER

Pull the drawer out until it stops.

Lift the front of the drawer until the

stops clear the guides.

Pull forward and remove the drawer.

C

B

A

7

Rail

Guide

Stop

Hinge

slot

Hinge

unlocked

position

Hinge

arm

STANDARD INSTALLATION

If the construction of your cabinet cannot

provide a 1/4″ flat area at the back of the

countertop opening, consider changing the

countertop to accommodate this dimension.

See Alternate Construction section.

NOTE: A 1-1/2″ minimum clearance must

be maintained between the rear edge of the

cooktop and the rear wall above the cooktop.

9

6

Installation Instructions

PRE-INSTALLATION CHECKLIST (CONT.)

PRE-INSTALLATION CUTOUT

AND REQUIRED CLEARANCES

If cabinets are placed less than 30″ above the

range, see Alternate Construction, Step 25D,

on page 18.

Wall coverings, counters and cabinets around

range must withstand heat (up to 194°F)

generated by the range.

8

12

″

23-3/16

″

7

″

A

c

e

p

ta

b

le

G

a

s

L

in

e

&

E

le

c

tr

ic

a

l

O

u

tle

t A

r

e

a

3

0

″ M

in

.

3

0

″

M

in

.

fr

o

m

c

o

k

in

g

s

u

r

fa

c

e

to

b

o

tto

m

o

f o

v

e

r

h

e

a

d

c

a

b

in

e

ts

S

h

a

v

e

R

a

is

e

d

E

d

g

e

T

o

C

le

a

r 3

1

-1

/8

″

W

id

e

C

o

n

tro

l P

a

n

e

l

9

-

1

/2

″

M

in

.

F

r

o

m

W

a

l

ls

1

3

″

M

a

x

.

d

e

p

th

For Optimum

Installation These

Surfaces Must

Be Flat & Level

F

o

llo

w

in

s

tru

c

tio

n

s

p

a

c

k

a

g

e

d

w

ith

a

lte

r

n

a

te

a

p

l

ia

n

c

e

C

o

u

n

te

rto

p

D

e

p

th

2

5

″

(ty

p

ic

a

l)

35-3/4

″

to 36-1/2

″

from floor to

countertop

18

″

Min. vertical

distance from the

bottom of the adjacent

overhead cabinets

1-1/4

″

Min. Counter top

to top of drawer

D

raw

er

c

o

r

d

, p

lu

g

,

r

e

c

e

p

t

a

c

l

e

b

o

x

3

.5

″

to

p

r

e

v

e

n

t

in

te

r

fe

r

e

n

c

e

&

g

a

s

h

o

k

u

p

Max. depth of

with drawer

9

/1

6

″

29-15/16"Min.

30-1/16" Max.

29-15/16

″

Min.

30-1/16

″

Max.

3

″

15

″

1/4″ min.

flat

9/16″

min.

flat

29-15/16″–30-1/16″

smooth cut

23-3/16″

typically

25″

typically

Wall

Flat area

R

1/4″

9/16″

min.

flat

36″

Front

Floor

Back

7

Installation Instructions

MAKING THE CONNECTIONS

(cont.)

Install 1/2″ flare union adaptor to the 1/2″

NPT elbow on pressure regulator.

Connect flexible appliance connector to

flare union.

Move range into approximate position

and connect flexible connector to gas

supply line with proper flare union

adaptor.

To prevent gas leaks, put a pipe joint

sealant or Teflon

®

tape on all male

threads. NOTE: Make sure sealant or tape

is compatible with Natural and LP gases.

When you are finished making

connections, be sure that all range knobs

are turned to OFF before you open the

main gas supply valve.

WARNING: Do not use a flame

to check for gas leaks. Use liquid leak detector

at all joints and connections to check for leaks

in the system.

I

H

G

F

E

10

GAS CONNECTIONS

MAKING THE CONNECTIONS

Install a manual shut-off valve in the gas

supply line in an easily accessible location.

Know how and where to shut off the gas

supply to the range.

Shut off gas supply before removing an

old range. Leave it off until hookup of

new range is finished.

Because solid pipe restricts moving the

range, we recommend use of a C.S.A.

certified flexible metal appliance

connector.

WARNING: Never reuse old

flexible connectors. The use of old flexible

connectors can cause gas leaks and personal

injury. Always use new flexible connectors

when installing a gas appliance.

D

C

B

A

10

3″

15″

12″

3

1

⁄2″

7″

Gas Inlet

Gas supply to

top burner

Pressure

regulator as

seen from

front of range

Pressure

regulator

Gas

supply

line

90° street

elbow

Shut-off valve Flexible gas line

7″ Max.

NOTE: When

screwing on the flare

union adaptor, hold

the gas inlet firmly

with a wrench.

8

Installation Instructions

ELECTRICAL CONNECTIONS

The range is shipped with a 4-

wire power cord. If your outlet

looks like the one shown, skip to

step 19 and proceed.

POWER CORD AND STRAIN

RELIEF INSTALLATION

Remove the wire

cover (on the back

of the range) by

removing 2

screws, using a

1/4″ nut driver.

Do not discard

these screws.

Remove the knockout ring (1-3/8″)

located on bracket directly below the

terminal block. To remove the knockout,

use a pair of pliers to bend the knockout

ring away from the bracket and twist

until ring is removed.

B

A

11

For power cord installations only (see the

next step if using conduit), assemble the

strain relief in the hole. Insert the power

cord through the strain relief and tighten.

Allow enough slack to easily attach the

cord terminals to the terminal block. If

tabs are present at the end of the winged

strain relief, they can be removed for

better fit.

NOTE: Do not install the power cord

without a strain relief. The strain relief

bracket should be installed before

reinstalling the rear range wiring cover.

For conduit installations only, purchase

a squeeze connector matching the

diameter of your conduit and assemble

it in the hole. Insert the conduit through

the squeeze connector and tighten. Allow

enough slack to easily attach the wires to

the terminal block.

NOTE: Do not install the conduit without

a squeeze connector. The squeeze

connector should be installed before

reinstalling the rear range wiring cover.

D

C

Wire Cover

Terminal block

(appearance

may vary)

Knockout

ring removed

Knockout ring

in bracket

Terminal

block

Bracket

Terminal

block

Strain relief

Power cord

Bracket

Squeeze

connector

Conduit

NEMA 14-50R

4-wire

9

Installation Instructions

NEW CONSTRUCTION AND

FOUR-CONDUCTOR BRANCH

CIRCUIT

All New Constructions, Mobile

Homes, Recreational Vehicles

and Installations Where Local

Codes Do Not Allow Grounding

Through Neutral Must Use the

4-Wire Cord Provided.

FOR EXISTING

CONSTRUCTION,

A THREE-WIRE FLEXIBLE

CORD KIT MAY BE USED

Follow instructions in step

14 if you require a 3-wire

cord:

13

12

3-WIRE POWER CORD

INSTALLATION

WARNING: The neutral or

ground wire of the power cord must

be connected to the neutral terminal

located in the center of the terminal

block. The power leads must be

connected to the lower left and

the lower right terminals of the

terminal block.

Remove the 3 lower terminal screws

from the terminal block. Insert the 3

terminal screws through each power

cord terminal ring and into the lower

terminals of the terminal block.

Be certain that the center wire

(white/neutral) is connected to the

center lower position of the terminal

block. Tighten screws securely into

the terminal block.

DO NOT remove the ground strap

connection.

WARNING: Before powering

the unit, ensure that the ground strap

is connected to both the terminal block

and to the ground plate.

Skip to Step 18 and proceed with the

installation.

B

A

14

NEMA 14-50R

4-wire

208/240 40 Amp

3-prong cord

Terminal block

(appearance

may vary)

Ground

plate

Power cord

Ground

strap

Neutral

terminal

ELECTRICAL CONNECTIONS (CONT.)

3-WIRE CONDUIT INSTALLATION

Loosen the 3 lower terminal screws

from the terminal block. Insert the center

bare wire (white/neutral) tip through the

bottom center terminal block opening.

On certain models, the wire will need

to be inserted through the ground strap

opening and then into the bottom center

block opening. Insert the two side bare

wire tips into the lower left and the lower

right terminal block openings. Tighten

the screws until the wire is firmly

secured (35 to 50 inch-lbs.). Do not over-

tighten the screws since it could damage

the wires.

NOTE: ALUMINUM WIRING:

Aluminum building wire may be used

but it must be rated for the correct

amperage and voltage to make

connection. Connect wires according

to this Step 16 or Step 17 depending

on number of wires.

Wire used, location and enclosure of

splices, etc., must conform to good

wiring practices and local codes.

Skip to Step 18 and proceed with the

installation.

B

A

16

10

Installation Instructions

4-WIRE POWER CORD

INSTALLATION

WARNING: The neutral wire of

the supply circuit must be connected to

the neutral terminal located in the lower

center of the terminal block. The power

leads must be connected to the lower

left and the lower right terminals of the

terminal block. The ground lead must be

connected to the frame of the range

with the ground plate and the ground

screw.

Remove the 3 lower terminal screws

from the terminal block. Remove the

ground screw and ground plate and

retain them.

Cut and discard the ground strap.

DO NOT DISCARD ANY SCREWS.

Insert the one ground screw into the

power cord ground wire terminal ring,

through the ground plate and into the

frame of the range.

Insert the 3 terminal screws (removed

earlier) through each power cord

terminal ring and into the lower

terminals of the terminal block. Be

certain that the center wire (white/

neutral) is connected to the center lower

position of the terminal block. Tighten

screws securely into the terminal block.

Skip to Step 18 and proceed with the

installation.

E

D

C

B

A

15

or

Terminal

block

Ground strap

Ground

strap

Neutral

terminal

Before

After

Terminal

block

Ground

screw

Ground

plate

(grounding

to range)

Bracket

Conduit

Wire tips

Terminal block

11

Installation Instructions

REINSTALL WIRE COVER

NOTE: When reinstalling the wire cover,

make sure that wires do not become pinched

between the wire cover and the housing.

NOTE: The ground strap must be attached

when using the 3-wire cord.

• Terminations must be either closed loop

terminals or open-end spade lugs.

• On some models, a filter capacitor may

be connected between the black and

ground leads on the junction block.

Do not remove capacitor.

18

4-WIRE CONDUIT INSTALLATION

Loosen the three lower terminal screws

from the terminal block. Remove the

ground screw and ground plate and

retain them. Cut and discard the ground

strap. DO NOT DISCARD ANY SCREWS.

Insert the ground bare wire tip between

the range frame and the ground plate

(removed earlier) and secure it in place

with the ground screw (removed earlier).

Insert the bare wire (white/neutral) tip

through the bottom center of the

terminal block opening. Insert the two

side bare wire tips into the lower left and

the lower right terminal block openings.

Tighten the screws until the wire is firmly

secured (35 to 50 inch-lbs.). Do not over-

tighten the screws since it could damage

the wires.

Proceed to Step 18.

C

B

A

17

or

Terminal

block

Ground strap

Neutral

terminal

Ground strap

Before

Terminal

block

Wire tips

Ground

screw

Bracket

Ground

plate

(grounding

to range)

After

12

Installation Instructions

INSTALL THE ANTI-TIP BRACKET

LOCATE THE BRACKET

a. Decide whether the bracket will be

installed on the right or left side of the

range opening.

b. Place the bracket as shown in Fig. 1.

A

19

Rear

leveling leg

Wall

FLOOR-CONCRETE

INSTALL THE RANGE

INSTALL THE ANTI-TIP BRACKET

(cont.)

INSTALL THE BRACKET IN WOOD OR

CONCRETE

INSTALLATION—WOOD CONSTRUCTIONS

a. Locate the centers of the 4 holes identified

in Fig. 1 as Floor–Wood and Wall.

b. Drill a 1/8″ pilot hole through the

pre-marked areas. Note the angle of the

wall screw in Fig. 2.

c. Mount the Anti-Tip bracket with the

4 screws provided.

INSTALLATION—CONCRETE CONSTRUCTIONS

a. For concrete installation, you will need

two 1/4″ x 1-1/2″ lag screws and two sleeve

anchors.

b. Locate the center of the 4 holes identified

in Fig. 1 as Floor–Concrete and Wall. Drill

the recommended size holes in each.

c. Install the sleeve anchors into the

predrilled concrete holes and install the

lag and wall screws through the Anti-Tip

bracket. Make sure the screws are securely

tightened.

B

19

FLOOR-WOOD

Bracket

side

Adjacent

cabinet

Top front

edge of

countertop

25″

Wall plate

Screw

must enter

wood or

metal

Bracket

Fig. 1

Fig. 2

13

Installation Instructions

SLIDE RANGE INTO OPENING

Position the range in front of the cabinet

opening.

Make sure the supports which overhang

the countertop clear the countertop.

If necessary, raise the unit by lowering

the leveling legs.

Push while lifting the range into the

opening, until the range is within 2″

of engaging the anti-tip bracket.

Remove the protective trim from the side

(if provided).

Using the adjustable pliers or wrench,

carefully screw in the back leveling leg

until the overhang comes to rest on the

countertop.

Carefully screw in the front two leveling

legs (similar to Step E) until the overhang

touches the countertop.

Carefully push the range into the opening

until the countertop fully engages the

control panel. The back maintop overhang

should cover the cutout opening.

G

F

E

D

C

B

A

20

SLIDE RANGE INTO OPENING

(cont.)

Plug the range cord into the receptacle.

Locate the cord in the back of the range

in a manner that it will not touch or be

moved by the drawer.

H

20

STORAGE DRAWER

Position range cord

so that there is no

interference with

storage drawer

Adjustable

wrench or pliers

Countertop

Make sure the edge of

the countertop fits flush

against the end of the

front control panel

FINAL CHECK OF ANTI-TIP

BRACKET

When installation is complete and the range is

in place, check to be sure that the rear leveling

leg is fully inserted into the slot of the Anti-Tip

Bracket.

21

INSTALL THE RANGE (CONT.)

14

Installation Instructions

REPLACE THE OVEN DOOR

NOTE: The oven door is heavy. You may need

help lifting the door high enough to slide it

into the hinge slots. Do not lift the door by

the handle.

Lift the oven door by placing one hand

on each side. The door is heavy, so you

may need help. Do not lift the door by

the handle.

With the door at the same angle as the

removal position (halfway between the

closed and broil stop position), seat the

notch of the hinge arm into the bottom

edge of the hinge slot. The notch of the

hinge arm must be fully seated into the

bottom of the slot.

Open the oven door as far as it will open.

Push the hinge locks up against the front

frame of the oven cavity, to the locked

position.

Close the oven door.

E

D

C

B

A

22

REPLACE THE STORAGE

DRAWER

Place the drawer rail on the guides.

Push the drawer in until it stops.

Lift the front of the drawer and push in

until the stops clear the guides.

Lower the front of the drawer and push in

until it closes.

SPECIAL INSTRUCTIONS IF YOU ARE

HAVING PROBLEMS WHILE REPLACING

THE STORAGE DRAWER

Remove and replace, making sure the power

cord is not obstructing the drawer and/or the

rail is in the guide.

Remove and replace, making sure the rail is in

the guide.

D

C

B

A

23

Stop

Bottom edge

of slot

Hinge in

locked position

Notch of hinge

securely fitted

into bottom of

hinge slot

Drawer does

not close

completely

Drawer

front panel

tipped away

from body

side

Rear drawer

support is on top

of guide rail on

the high side

Drawer front panel

tipped to one side

Hinge arm

Hinge notch

If Drawer Won’t Close:

If Drawer is Crooked:

Power cord

may be

obstructing

drawer

in this area

Rear drawer

support is

resting on top

of guide rail

c.

Front right burner

Make sure the hole

in the burner head

assembly is positioned

over the electrode and

that the burner head

is fully inserted inside

the burner base. A

small gap between

the base and head

is normal.

Front left

burner, back

right burner

and back left

burner

Make sure

the slot in the

burner head is

positioned over

the electrode.

The burner cap

has three to four pins. When placing the cap,

make sure none of the pins sits in the stability

chamber.

d. Place the burner grates over the burners.

COOKTOP BURNERS

ASSEMBLE THE BURNERS

CAUTION: The electrode of the

spark igniter is exposed. Be careful not to

push any cooktop controls while the top

of the burner is removed. Do not remove

the top or touch the electrode of any burner

while another burner is turned on. Electrical

shock might result.

a. Place the burner head onto the burner

base, making sure that the head is properly

oriented over the burner base and the

electrode. Make sure to place the correct

burner head on the correct burner base

and that the burner head sits level on the

burner base. The burner heads are not

interchangeable.

b. Place the burner

caps on the burner

heads, making sure

to place the correct

burner cap on the

correct burner head.

The burner caps are

not interchangeable.

Make sure that the

burner caps are

properly seated on

the burner heads.

A

24

15

Installation Instructions

Burner cap

Burner head

Burner base

Electrode

Burner cap

Burner

head

Burner base

Electrode

Stability

chamber

Burner cap not properly seated

Burner cap properly seated

Medium

head

Front of range

Large head

Small head

Extra large head

INSTALL THE RANGE (CONT.)

16

Installation Instructions

CHECK THE IGNITERS

Operation of the electric igniters should be

checked after the cooktop and supply line

have been carefully checked for leaks and the

cooktop has been connected to the electrical

power.

a. Turn on gas.

b. Push and turn a burner valve to the LITE

position.

• The burner valve should light when gas

is available to the burner.

• Once the burner lights, it should be

turned out of the LITE position.

c. Try each valve separately until all burners

have been checked.

D

BURNER IGNITION

Cooktop Spark Ignition—When you turn

the cooktop knob to LITE, the spark igniter

makes a series of electric sparks (ticking

sounds) which light the burner. During a

power failure the burners will not light

automatically. In an emergency, a cooktop

burner may be lit with a match by following

the steps below.

WARNING: Lighting gas burners

with a match is dangerous. You should match

light the cooktop burners only in an

emergency.

a. Light a match and hold the flame near the

burner you want to light. Wooden matches

work best.

b. Push in and turn the control knob slowly.

Be sure you are turning the correct knob

for the burner you are lighting.

NOTE: If the burner does not light within

five seconds, turn the knob off and wait

5 minutes before trying again.

E

BURNER FLAMES

Turn each burner on. Flames should be blue

in color with no trace of yellow. The burner

flames should not flutter or blow away from

the burner. The flame should be no less than

1/4″ on the lowest setting and no greater than

1-1/2″ on highest setting.

Burners should be checked frequently

WARNING: If you attempt

to measure the flame, please use caution.

Burns could result.

F

CHECK FOR LEAKS

Turn the gas supply on and use a liquid

leak detector (soap solution) at all joints and

connections to check for leaks. Do not use an

open flame to look for leaks. Be sure all leaks

are stopped before lighting burners.

B

PRESSURE TEST INFORMATION

The maximum allowable supply pressure

for the regulator is 14″ W.C. The minimum

supply pressure needed to check the regulator

setting is 7″ W.C. for natural gas and 10″ W.C.

for LP gas.

WARNING: The range and its

individual shut-off valve must be disconnected

from the gas supply piping system during any

pressure testing of the gas supply system at

test pressures of more than 1/2 psig (pounds

per square inch gauge). The range must be

isolated from the gas supply piping system

by closing its individual shut-off valve during

any pressure testing of the gas supply system

at test pressures equal to or greater than

1/2 psig. NOTE: 1/2 psig = 13.855″ w.c.

C

Cooktop Burner

1/4″ to

1-1/2″

17

Installation Instructions

ALTERNATE CONSTRUCTION

PREPARATION

OPTIONAL MAINTOP FILLER OR

BACKGUARD KIT

If counter opening extends to the wall, it will

require Maintop Filler Kit (supplied with the

range) or Backguard Kit (JXS32XX or

JXS37XX) to close the gap.

NOTE: If the countertop is greater than 25″,

it will show a gap between the backguard

and wall or between filler kit and the wall.

If the countertop is less than 25″, a gap will

occur between the countertop front and the

control panel ends (see Step 8).

If you are using the optional backguard kit,

refer to the backguard kit instructions for

installation details.

If you use the filler kit, place the metal filler

piece supplied with the range to the back of

the range as shown in the figure below. Start

the 2 screws into the upper holes at the

outside rear of the range and through the

slots in the trim, holding the filler piece

centered on the maintop frame and pushing

upward to close the gap between the bottom

of the maintop and the filler trim.

A

25

When the trim is set in the proper position,

tighten the 2 mounting screws. The top of the

trim should be located below the top surface

of the maintop to prevent pots, pans and

skillets from damaging the painted parts.

Refer to the Standard Installation of the

Range on page 6.

Wall

25″

Must be

level

Must be

flat

30″

smooth cut

Must be level

31-1/8″

Must

be

flat

(2) #8

screws

Maintop filler

Range

Cooktop

FOR NON-BUILT-IN INSTALLATION

(END OF CABINET LOCATION)

When installing the range at the end of

a cabinet section which will expose the

unfinished side of the range, use Body Side

Kit (JXS77XX). Refer to the kit instructions

for installation details.

B

INSTALL THE RANGE (CONT.)

Please see L.P. conversion instructions

supplied with this range when L.P. Gas

is used.

NOTE: Instructions are mounted on

regulator bracket.

18

Installation Instructions

ALTERNATE CONSTRUCTION

PREPARATION (cont.)

ISLAND INSTALLATION

Attach the Anti-Tip bracket per instructions

in Step 19, making sure that the rear of the

bracket is 25″ from the front of the

countertop.

Be aware that the screws provided are long

and may penetrate through the back of the

island cabinets. In this event, use shorter

screws (not provided) or the screws provided

should be used in the floor (see Step 19B for

Wood/Concrete Floor Installation).

Do not use Backguard Kit JXS32XX or

JXS37XX.

C

25

CABINETS OVER THE RANGE LESS

THAN 30″

If a 30″ clearance between cooking surface

and overhead combustible material or metal

cabinets cannot be maintained, protect the

underside of the cabinets above the cooktop

with not less than 1/4″ insulating millboard

covered with sheet metal not less than

0.0122″ thick.

D

OPERATION CHECKLIST

• Double check to make sure everything in

this guide has been completed. Rechecking

steps will ensure safe use of the cooktop.

• Make sure all controls are left in the OFF

position.

• Make sure the flow of combustion

and ventilation air to the cooktop is

unobstructed.

• The serial plate for your Range is located

under the oven door above the storage

area. In addition to the model and serial

numbers, it tells you the ratings of the

burners and the type of fuel and pressure

the cooktop was adjusted for when it left

the factory.

• When ordering parts, always include the

serial number and model number to ensure

proper replacement parts.

• Recheck Steps: Double check to make

sure everything in this guide has been

completed. Rechecking steps will ensure

safe use of the Range.

26

19

Notes

20

Printed in the United States

La page est en cours de chargement...

GE Profile P2S975WEMWW Guide d'installation

Ce manuel convient également à

GE Profile P2S975WEMWW Guide d'installation

dans d''autres langues

Documents connexes

Autres documents