Sun Joe SPX2688-MAX-RM Mode d'emploi

Marque: Sun Joe

Modèle: SPX2688-MAX-RM

Catégorie: Nettoyeurs haute pression

Taper: Mode d'emploi

A Division of Snow Joe®, LLC

OPERATOR’S MANUAL

Model SPX2688-MAX Form No. SJ-SPX2688-MAX-880E-M

13A ELECTRIC PRESSURE WASHER

2050 PSI MAX PRESSURE AT INITIAL DISCHARGE PER CSA INTERNAL PRESSURE TESTING

1.8 GPM MAX FLOW WITH NOZZLE OPEN AT MINIMUM PRESSURE

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

mWARNING! This indicates a hazardous situation, which,

if not avoided, could result in death or serious injury.

mCAUTION! This indicates a hazardous situation, which,

if not avoided, could result in minor or moderate injury.

mDANGER! This indicates a hazardous situation, which,

if not followed, will result in death or serious injury.

General Safety

mWARNING! This appliance is not intended for use

by children or by unassisted, unsupervised persons whose

physical, sensory or mental capabilities prevent them from

using it safely. Children should be supervised to ensure that

they do not play with the appliance.

Before starting up your machine, please check it carefully for

any defects. If you nd any, do not start up your machine.

Contact your authorized Snow Joe® + Sun Joe® dealer or

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

mWARNING! When using the pressure washer, basic

safety precautions should always be followed to reduce the

risk of re, electric shock, and personal injury. These include:

• Know your product – Know how to stop the machine and

bleed pressure quickly. Thoroughly familiarize yourself with

the controls.

• Keep bystanders away – All visitors and pets should be

kept a safe distance away from the work area.

• Use the right product – Do not use this machine for any

job except that for which it is intended.

• Dress properly – Do not wear loose clothing or jewelry.

They can get caught in moving parts. Protective rubber

gloves and non-slip footwear are recommended when

working outdoors.

• mCAUTION! – Exercise caution to avoid slipping or falling.

Wear protective footwear that will protect your feet and

improve your footing on slippery surfaces.

• Stay alert – Watch what you are doing. Use common

sense. Do not operate the pressure washer when you are

tired, or under the inuence of alcohol or drugs.

• Do not overreach – Keep proper footing and balance at

all times.

• Avoid unintentional starting – Do not carry a plugged-

in machine with your nger on the trigger. Make sure the

switch is o before plugging in the machine.

• Do not abuse the cord – Never carry the machine by the

cord or yank the cord to disconnect it from the receptacle.

Keep the cord away from heat, oil, and sharp edges.

• Use safety glasses – Also use safety footwear, snug-tting

clothing, protective gloves, hearing and head protection.

• Check the water temperature – This pressure washer

is not meant to pump hot water. NEVER connect it to a

hot water supply as it will signicantly reduce the life of

the pump.

• Store indoors – NEVER store the pressure washer

outdoors or where it could freeze. The pump could be

seriously damaged.

• Ground Fault Circuit Interrupter (GFCI) – This product

is provided with a ground fault circuit interrupter built into

the power cord plug. If replacement of the plug or cord is

needed, use only identical replacement parts.

• Inspect electrical cords – The insulation of the power cord

should be perfectly intact. If the power cord is damaged or

shows any signs of wear or tear, do not use the pressure

washer. Contact your authorized Snow Joe® + Sun Joe®

dealer or call the Snow Joe® + Sun Joe® customer service

center at 1-866-SNOWJOE (1-866-766-9563).

mWARNING! Do not use this appliance without reading

this instruction manual.

mWARNING! This appliance has been designed for

use with cleaning agents that are recommended by the

manufacturer. The use of other cleaning agents or chemicals

may adversely aect the safety of the appliance.

mWARNING! Do not use the appliance within range of

persons unless they are wearing protective clothing.

mWARNING! High-pressure jets can be dangerous if

subject to misuse. The jet must not be directed at persons,

pets, live electrical equipment, or the appliance itself.

• Do not direct the jet at yourself or others in order to clean

clothes or footwear.

• Risk of explosion – Do not spray ammable liquids.

• Disconnect the tool – Disconnect from the electrical power

supply before performing any maintenance task.

• Keep children away – This high-pressure electric

power washer must not be used by children or

untrained personnel.

• To ensure appliance safety, use only original

replacement parts from the manufacturer or those

approved by the manufacturer.

mWARNING! Water that has owed through backow

preventers is considered to be non-potable.

mWARNING! During cleaning, maintenance or when

replacing parts, the machine must be disconnected from its

power source by removing the plug from the socket outlet.

mWARNING! High-pressure hoses, ttings, and

couplings are important for the safe operation of the

appliance. Use only hoses, ttings, and couplings

recommended by the manufacturer.

• Check for damaged parts – Do not use the appliance if

the supply cord or other important parts of the appliance

are damaged (e.g. safety devices, high-pressure hose,

trigger gun).

mWARNING! If an extension cord is used, the plug and

socket must be of watertight construction.

mWARNING! Inadequate extension cords can be

dangerous.

• This high-pressure electric power washer must not be used

at temperatures below 32ºF (0°C).

mWARNING! Power cords on drums should always be

completely unwound to prevent the cord from overheating.

• Power cord connections should be kept dry and o

the ground.

• If the power cord is damaged, do not use the appliance.

Contact your authorized Snow Joe® + Sun Joe® dealer or

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

• Keep the machine on a stable, at surface during operation,

handling, transportation, and storage. Sudden overturn of

the machine can cause bodily injury.

• In the event of an accident or breakdown, switch o the

machine immediately. (If contact with detergent occurs,

rinse with an abundance of clean water.)

Electrical Safety

ATTENTION: If there are problems with the electrical mains,

short voltage drops may appear when starting the equipment.

This can, in turn, inuence other equipment (e.g. cause a

lamp to blink). If the MAINS-IMPEDANCE Zmax < 0.335 OHM,

such disturbances are not expected (if you require assistance,

contact your local supply authority for further information).

mWARNING! Electrical Shock Hazard – Before starting

up your machine, please check it carefully for any defects.

If you nd any, do not start up your machine and contact

your distributor.

The following should be observed when connecting the

high-pressure electric power washer to the electric supply:

• The electric supply connection should be performed by a

qualied person.

• The electric supply to this appliance should include either

a residual current device that will interrupt the supply if the

leakage current to the earth exceeds 30 mA for 30 ms or a

device that will interrupt the earth circuit (GFCI).

IMPORTANT: Only use water without any impurities.

If there is a risk of running sand into the inlet water (i.e. from

your own well), an additional lter should be installed.

Safety Devices

The spray gun features a locking device. When the lock is

activated, the spray gun cannot be operated.

1. Thermal sensor – A thermal sensor protects the motor

against overloading. If the thermal sensor is activated and

the power is cut o, wait for a while until the motor is cool

and restart the unit.

2. Double insulation – In a double-insulated appliance, two

systems of insulation are provided instead of grounding.

No grounding means is provided on a double-insulated

appliance, nor should a means for grounding be added

to the appliance. Servicing a double-insulated appliance

requires extreme care and knowledge of the system, and

should be performed only by qualied service personnel at

an authorized Snow Joe® + Sun Joe® dealer. Replacement

parts for a double-insulated appliance must be identical

to the parts they replace. A double-insulated appliance

is marked with the words “Double Insulation” or “Double

Insulated.” The symbol (square within a square) may

also be marked on the appliance.

3. Ground fault circuit interrupter (GFCI) protection – This

pressure washer is provided with a ground-fault circuit-

interrupter (GFCI) built into the plug of the power-supply

cord. This device provides additional protection from the

risk of electric shock. Should replacement of the plug or

cord become necessary, use only identical replacement

parts that include GFCI protection.

4. It is not recommended to use an extension cord with this

pressure washer. The unit comes standard with a 35 ft

GFCI power cord. Using an extension cord may cause

a drop in line voltage resulting in loss of power

and overheating.

If an extension cord is going to be used, use only

extension cords that are intended for outdoor use. These

extension cords are identied by marking "Acceptable

for use with outdoor appliance; store indoors while not

in use". Use only extension cord having an electrical

rating not less than the rating of the product. Do not use

damaged extension cords. Examine extension cord before

using and replace if damaged. Do not abuse extension

cord and do not yank on any cord to disconnect. Keep

cord away from heat and sharp edges. Always disconnect

extension cord from the receptacle before disconnecting

the product from the extension cord.

5. To reduce the risk of electric shock, this appliance has

a polarized plug (i.e. one blade is wider than the other).

The appliance plug will t into a polarized outlet only

one way.

If the appliance plug does not t fully into the outlet,

reverse the plug. If the plug still does not t, make sure

that you are using the correct polarized wall outlet. If the

plug still does not t, contact a qualied electrician to

install the proper wall outlet. Do not modify the

appliance plug, power cord receptacle, or power cord

plug in any way.

mWARNING! To reduce the risk of electrocution, keep

all connections dry and o the ground. Do not touch plug with

wet hand.

6. To prevent the appliance cord from disconnecting from the

extension cord during operation, make a knot with the two

cords as shown in Table 1.

7. Do not abuse the cord. Never pull the pressure washer

by the cord or yank the cord to disconnect it from the

receptacle. Keep the cord away from heat, oil, and

sharp edges.

Risk of electrocution

• Inspect cord before using.

• Do not use if cord is damaged.

• Keep all connections dry and o the ground.

• Do not touch plug with wet hands.

• Keep cord away from heat and sharp edges.

• Do not spray electrical apparatus and wiring.

Risk of explosion

• Do not spray ammable liquids.

• Do not use acids, bases, solvents, or any ammable

material in this product. These substances can cause

physical injuries to the operator and irreversible damage

to the machine.

Additional safety instructions

• High-pressure: keep clear of nozzle.

• Injection hazard: equipment can cause serious injury if the

spray penetrates the skin.

• Do not point the gun at anyone or at any part of the body.

• In case of skin penetration, seek medical aid immediately.

• Before servicing, cleaning, or removing any parts, shut o

the power and relieve pressure.

• This machine is not suitable for connection to the potable

water mains.

m WARNING m

Electric shock may cause SEVERE INJURY or

DEATH. Heed these warnings:

• Do not allow any part of the electric pressure washer

to make contact with water while it is in operation. If

the appliance becomes wet while turned o, wipe dry

before starting.

• Do not use an extension cord over 25 ft. The

pressure washer comes equipped with a 35 ft power

cable. Combined cord length must not exceed 60 ft.

Any extension cord must be 14-gauge (or heavier) to

safely power the pressure washer.

• Do not touch the appliance or its plug with wet hands

or while standing in water. Wearing rubber boots

oers some protection.

EXTENSION CORD CHART

Cord Length:

Min. Wire Gauge (A.W.G.):

25 ft (7.6 m)

(B) Connect plug and receptacle

Cord set Appliance cord

(A) Tie cord as shown

Table 1. Method of Securing Extension Cord

Product Description

Purpose

• This electric high pressure washer is intended for residential

use only. It is designed for medium-to-heavy duty cleaning

jobs on boats, motorcycles, RV’s, ATV’s, trailers, decks,

barbecues, siding, patio furniture, and more.

Areas of application

• Never use the machine in potentially explosive areas under

any circumstances!

• The operating temperature must be between 32ºF (0ºC) and

104ºF (40ºC).

• The machine consists of an assembly with a pump,

which is encased in a shock-absorbing housing. To

provide the operator with an optimal working position,

the machine is equipped with a spray wand and a non-slip

handle grip, whose shape and conguration comply with

applicable regulations.

• Do not cover or modify the spray wand or the spray nozzle

in any way.

• The high-pressure electric power washer is designed to be

used with cold or lukewarm water; higher temperatures can

damage the pump.

• Do not use water that is dirty, gritty, or contains any

chemical products, as such impurities could impair

operation and shorten the life of the machine.

Safety Symbols

The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all

instructions on the machine before attempting to assemble and operate.

To reduce the risk of injury, user

must keep all bystanders at least

49 ft (15 m) away.

Always keep the power cable

away from heat sources, oils, or

sharp edges. Immediately remove

plug from the mains if the cable is

damaged, frayed, or entangled.

READ THE OPERATOR'S

MANUAL(S) – Read, understand,

and follow all instructions in the

user manual(s) before attempting

to assemble and operate.

SAFETY ALERT – Indicates a

precaution, a warning, or a danger.

WEAR EYE AND HEARING

PROTECTION – For protection

against injury, wear ear defenders

and safety goggles.

Double Insulation – When servicing, use only identical replacement parts.

WARNING! Do not expose the

unit to rain or wet conditions.

Keep dry.

Machine not suitable for connection

to the potable water mains.

WARNING! Electrical shock hazard.

WARNING! Turn the machine OFF

and disconnect it from the power

supply before inspecting, cleaning,

changing accessories, or conducting

any other maintenance task.

Symbols SymbolsDescriptions Descriptions

Wear non-slip footwear that will

protect your feet and improve your

footing on slippery surfaces.

Wear safety gloves during

use to protect hands.

Store indoors. Never store the

pressure washer outdoors.

If the pump freezes, permanent

damage may result.

Know Your Electric Pressure Washer

Read the owner’s manual and safety rules carefully before operating the pressure washer. Compare the illustration below

to the unit in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for

future reference.

1. Trigger gun

2. On/O switch

3. Water outlet/high-pressure hose

connection

4. Garden hose adapter/

connection

5. Power cord with GFCI

6. Wheels (2)

7. Needle clean-out tool

8. Cord holder

9. Top handle

10. High-pressure hose holder

11. High-pressure hose

12. On-board nozzle storage

13. 0º Quick-Connect nozzle (red)

14. 15º Quick-Connect nozzle (yellow)

15. 40º Quick-Connect nozzle (gray)

16. Foam adjusting cap

17. Detergent nozzle

18. Foam cannon bottle

19. Spray wand protector

20. Brass quick-connect collar

21. Spray wand

22. Trigger gun holder

23. High-pressure hose connection

24. Trigger

25. Safety lock

Technical Data

Rated Voltage ...................................................... 120V ~ 60 Hz

Motor ............................................................................ 13-amp

Max Water Inlet Temperature ................................. 104ºF/40ºC

Max Water Inlet Pressure ............................................ 0.7 MPa

Foam Cannon Capacity ...................................... 33.8  oz (1 L)

High Pressure Hose Length ....................................... 20 ft (6 m)

Power Cord Length .............................................. 35 ft (10.7 m)

Max Pressure at initial discharge ................................ 2050 PSI

per CSA internal pressure testing

Rated Pressure under typical load .............................. 1600 PSI

Max Flow with nozzle open ....................... 1.8 GPM (6.8 L/min)

at minimum pressure

Rated Flow under typical load ................... 1.1 GPM (4.2 L/min)

Net Weight ....................................................... 15.8 lbs (7.2 kg)

Unpacking

Carton Contents

• Electric pressure washer

• Top handle

• High-pressure hose holder

• Spray wand protector

• Trigger gun holder

• Cord holder

• 4.8 x 16 screws (7)

• Spray wand

• Trigger gun

• Three (3) Quick-Connect nozzles (0º, 15º, 40º)

• Needle clean-out tool (included with manual packet)

• High-pressure hose

• Garden hose adapter (female coupler)

• Manual with registration card

1. Carefully remove the pressure washer and check to see

that all of the above items are supplied.

2. Inspect the product carefully to make sure no breakage or

damage occurred during shipping. If you nd damaged or

missing parts, DO NOT return the unit to the store. Please

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

NOTE: Do not discard the shipping carton and packaging

material until you are ready to use your new electric

pressure washer. The packaging is made of recyclable

materials. Properly dispose of these materials in

accordance with local regulations.

IMPORTANT! The equipment and packaging material are

not toys. Do not let children play with plastic bags, foils,

or small parts. These items can be swallowed and pose a

suocation risk!

mWARNING! Do not connect to power supply until

assembly is complete. Failure to comply could result in

accidental starting and possible serious personal injury.

Assembly

Tools required: Phillips head screwdriver

1. Slide the top handle in position on the top of the pressure

washer, and attach using the three screws as shown

(Fig. 1).

2. Attach the high-pressure hose holder and secure using the

four additional screws provided, as shown (Fig. 2).

3. Slide the cord holder into position (Fig. 3).

Fig. 1

Top handle

Screws

Screw

Fig. 2

High-pressure

hose holder Fix with

4 screws

4. Slide the trigger gun holder into position (Fig. 4).

5. Slide the spray wand protector into position (Fig. 5).

6. To connect the spray wand with the trigger gun, press

the wings of the spray wand into the slot of the trigger

gun, then twist counterclockwise until the 2 parts are

completely locked together (Fig. 6).

7. Connect the high-pressure hose to the trigger gun. Twist

to secure the connection (Fig. 7).

8. Connect the other end of high-pressure hose to the water

outlet on the washer and tighten securely (Fig. 8).

Fig. 3

Cord holder

Fig. 4

Trigger gun

holder

Fig. 5

Spray wand

protector

Trigger gun

Spray wand

Fig. 6

Spray wand wings

Fig. 7

High pressure hose

Trigger gun

Fig. 8

Water outletHigh-pressure

hose

mWARNING! Keep hose away from sharp objects.

Bursting hoses may cause injury. Examine hoses regularly and

replace if damaged. Do not attempt to mend a damaged hose.

9. Connect the garden hose adapter (female coupler) to

the water inlet of the pressure washer, then thread your

garden hose (male end) into the garden hose adapter

(Fig. 9). The garden hose must have an internal

diameter of at least 13 mm (1/2 in.) and must be

reinforced. The water supply must be at least equal to the

washer delivery capacity.

NOTE: The machine is not suitable for connection to the

potable water main.

10. Attach garden hose to water supply (Fig. 10).

mWARNING! Do not connect to potable water system.

mWARNING! If connection is made to a potable water

system, the system shall be protected against backow.

mWARNING! The intake water temperature must not

exceed 104ºF/40ºC. The water supply must not exceed

0.7 MPa.

mCAUTION! The washer must only be used with clean

water; use of unltered water containing corrosive chemicals

will damage the washer.

mCAUTION! To prevent damage to the appliance, do not

allow it to operate dry. Before starting the appliance, make

sure that it has proper and stable supply of water.

Operation

Using the Pressure Washer

mIMPORTANT! This pressure washer is equipped with

a micro-switch sensitive to water ow. This Total Stop System

(TSS) senses water ow in the pump. When the trigger is

released, water stops owing through the pump. The TSS then

automatically turns the motor o to protect the pump from

overheating, thus saving energy and prolonging pump life.

1. Position the washer as CLOSE as possible to the

water supply.

2. The washer must be used on a secure and stable surface

in a standing, upright position (Fig. 11).

3. Make sure the unit is switched o before plugging the unit

into the power outlet.

4. Check that the electrical supply voltage and frequency

(Volt/Hz) correspond to those specied on the rating plate.

If the power supply is correct, you may now plug the

pressure washer into the power outlet (Fig. 12).

Fig. 9

Garden hose

This end to

water inlet

Garden hose

(male end)

Water inlet

Fig. 10

Connect to water supply

Garden hose

Fig. 11

RESET

TEST

Fig. 12

GFCI

Reset

NOTE: The GFCI may need to be reset when rst plugged

into the electric outlet. Press the "Reset" button until

the power light indicator on the GFCI illuminates when

plugged in.

5. Turn the water supply tap on completely.

6. Release the safety lock, then press the trigger for a few

seconds until the water ow is steady. Operating the

pressure washer in this manner will allow air to escape

and discharge residual pressure in the hose (Figs. 13 – 14).

7. Turn the ON/OFF switch to the ON (I) position to start the

pressure washer (Fig. 15).

Fig. 15

ON/OFF switch

8. When re-starting the motor, always keep the trigger

pressed.

NOTE: The motor only runs when the trigger is operated

and shuts o when the trigger is released.

Using Nozzles

Before beginning any cleaning task, determine the best nozzle

for the job. Each of the nozzles has a dierent spray pattern.

The nozzle patterns are 40˚ (for gentle cleaning), 15˚ (for tough

jobs), and 0˚ (for spot cleaning or hard-to-reach areas) .

mCAUTION! NEVER change nozzles without locking the

safety lock on the trigger handle.

mWARNING! High-pressure jets can be dangerous if

subject to misuse. The jet must not be directed at persons,

pets, live electrical equipment, or the appliance itself.

This electric pressure washer is equipped with three (3) Quick-

Connect nozzles that easily snap onto the Quick-Connect

collar of the spray wand.

To connect a nozzle to the spray wand:

1. Turn o the pressure washer and shut o the water supply.

Pull the trigger to release water pressure.

2. Engage the safety lock on the trigger handle.

3. Pull back the brass Quick-Connect collar and insert the

desired nozzle into the collar. Release the collar and the

nozzle will click into place (Fig. 16).

Fig. 13

Safety lock

Fig. 14

Trigger

To disconnect a nozzle from the spray wand once the cleaning

job is complete:

1. Turn o the pressure washer and shut o the water supply.

Pull the trigger to release water pressure.

2. Engage the safety lock on the trigger handle.

3. Remove the nozzle by disconnecting it while pulling back

the brass Quick-Connect collar.

mWARNING! Do not make changes to the nozzle while

the trigger is engaged. Doing so could result in damage to the

pressure washer or injury to the user.

Working with Detergents

When cleaning with the pressure washer, some cleaning tasks

can be solved with water alone, but for most tasks cleaning

with detergent allows for more eective dirt removal.

mWARNING! Use only detergents specically designed

for use with pressure washers, such as Sun Joe® HOUSE +

DECK WASH (SPX-HDC1G), Sun Joe® SNOW FOAM AUTO

WASH (SPX-FCS1G), or Sun Joe® HEAVY DUTY CLEANER

(SPX-APC1G). DO NOT USE household detergents, acids,

alkaline solutions, bleaches, solvents, ammable material,

or industrial grade solutions. These could damage the

pressure washer. Many detergents may require mixing prior

to use. Prepare the cleaning solution as instructed on the

solution bottle.

1. Gently pull the foam cannon bottle out of its storage

position (Fig. 17).

2. Remove the cap. Fill the bottle or mix as recommended by

detergent instructions (Fig. 18), and replace it back on the

unit. Secure the cap back into place.

3. Disconnect the spray wand from the trigger gun by

pressing it in rmly and twisting clockwise until the 2

wings of the spray wand can be removed from the slot

(Fig. 19).

Fig. 16

Spray wand quick-

connect collar

Nozzle

Pull back

Fig. 17

Foam

cannon

bottle

Fig. 18

Detergent

for pressure

washer

Foam cannon bottle

Fig. 19

Press the spray

wand inside

Twist the spray

wand as shown

4. To connect the foam cannon with the trigger gun, press

the wings of the foam cannon into the slot of the trigger

gun, then twist until the 2 parts are completely locked

(Fig. 20).

5. Turn on the pressure washer. Pull the trigger to operate the

unit. The liquid detergent will automatically mix with water

and be discharged through the nozzle.

NOTE: The spray angle can be adjusted from 0° to 45° by

rotating the foam cannon nozzle. The foam volume can

be adjusted by rotating the adjustable cap, as indicated

below (Fig. 21).

mWARNING! Do not adjust the foam cannon while the

trigger is squeezed. Failure to do so could result in damage.

mCAUTION! Always test the detergent in an

inconspicuous area before use.

6. Apply detergent from the bottom to the top of the dry

surface to be cleaned.

NOTE: Wetting the surface rst is not recommended as it

dilutes the detergent and reduces its cleaning ability.

7. Allow the detergent to remain on the surface for a short

time before rinsing. Do not allow the detergent to dry on

the surface.

mCAUTION! Damage may occur to painted surfaces if

the detergent is allowed to dry on the surface. Wash and rinse

a small section at a time. Avoid working on hot surfaces or in

direct sunlight.

8. When nished using the pressure washer, you must rst

drain and rinse the foam cannon bottle. Run the pressure

washer until all of the soap is drained from the foam

cannon bottle.

mCAUTION! Failure to follow these cleaning instructions

will cause the injection system to become clogged and

inoperable.

mIMPORTANT! NEVER USE:

• Bleach, chlorine products, and other corrosive chemicals

• Liquids containing solvents

(e.g. paint thinners, gasoline, oils)

• Tri-sodium phosphate products

• Ammonia products

• Acid-based products

These chemicals will harm the unit and will damage

the cleaning surface.

Shutting down

1. Turn the switch to the OFF (0) position and unplug the

power cord from the outlet.

2. Turn o the water source.

3. Hold the trigger to release water pressure.

4. Disconnect the garden hose from the water inlet on

the unit.

5. Disconnect the high-pressure hose connection on the

trigger gun handle.

6. Release the trigger and engage the gun safety lock.

mWARNING! Turn o the water supply and squeeze the

trigger to depressurize the unit. Failure to do so could result in

personal injury due to discharge of high-pressure water.

Taking a break

If you are taking a break of ve minutes or more between

cleaning tasks:

1. Engage the gun safety lock on the back.

2. Turn the switch to the OFF (0) position.

3. Unplug the power cord from the outlet.

Fig. 20

Trigger gunFoam cannon

Foam cannon

wings

Fig. 21

Adjustable cap

Decrease soap

volume

Increase soap

volume

Adjustable

nozzle

Pencil jet Fan spray

Storage

mCAUTION! Always store your pressure washer in a

location where the temperature will not fall below 32ºF (0ºC).

The pump in this machine is susceptible to permanent damage

if it freezes. FREEZE DAMAGE IS NOT COVERED BY THE

WARRANTY.

• Store the pressure washer indoors in a dry, covered area

where it is not subject to adverse weather conditions.

• It is important to store this product in a frost-free area.

• Always empty water from the hoses, the pump, and the

foam cannon bottle (if using) before storing.

mCAUTION! The use of a pump protector is

recommended to prevent cold weather damage during storage

over the winter months.

Winterizing + long-term storage

If you must store your pressure washer in a location where

the temperature falls below 32ºF (0ºC), you can minimize the

chance of damage to your machine by utilizing the following

procedure:

• Disconnect all water connections.

• Turn on the pressure washer for a few seconds until the

remaining water in the pump exits. Turn o immediately.

• Do not allow the high-pressure hose to become kinked.

• Store the machine and accessories in a room that does

not reach freezing temperatures.

• Do not store near a furnace or other sources of heat that

may dry out the pump seals.

• Operate the pressure washer with non-corrosive/non-toxic

anti-freeze, a pump saver, or a pump protector before

storing for the winter.

mWARNING! Before reusing, completely ush the

unit out with clear water. Anti-freeze products can damage

paintwork, so you must ensure there is no anti-freeze left in the

system before using it again.

Maintenance

mCAUTION! Before working on the pressure washer,

disconnect the plug from the power supply socket.

Clean the Adapter Filter and the Nozzle

1. To ensure good performance, check and clean the adapter

lter (Fig. 22). Remove the lter and rinse with warm water

to prevent any foreign matter from clogging the pump

(Fig. 23).

2. Clean the nozzle with the needle clean-out tool provided

(Fig. 24). Remove the nozzle from the spray wand; remove

any dirt from the nozzle hole and rinse.

Fig. 22

Adapterlter

Garden hose

adapter

Fig. 23

Filter

15º

Fig. 24

Needle clean-out tool

Disposal

Recycling the Pressure Washer

• Do not dispose of electrical appliances as unsorted

municipal waste. Use separate collection facilities.

• Contact your local government agency for information

regarding the collection systems available.

• If electrical appliances are disposed of in landlls

or dumps, hazardous substances can leak into the

groundwater and get into the food chain, damaging your

health and well-being.

Service + Support

If your Sun Joe® SPX2688-MAX electric pressure washer

requires service or maintenance, please call the Snow Joe® +

Sun Joe® customer service center at 1-866-SNOWJOE

(1-866-766-9563).

Model + Serial Numbers

When contacting the company, reordering parts, or arranging

service from an authorized dealer, you will need to provide the

model and serial numbers, which can be found on the decal

located on the housing of the unit. Copy these numbers into

the space provided below.

S P X 2 6 8 8 - M A X

Record the following numbers from the housing or handle of your

new product:

Model #:

Serial #:

Troubleshooting

• Disconnect the unit from the electrical power supply before carrying out maintenance on the machine or when checking that

its parts are in proper working order.

• To avoid unnecessary hassles, consult the following table before contacting customer service with any mechanical issues.

Problems Possible Cause Possible Solution

Machine refuses

to start

• Power failure/machine not

plugged into a working receptacle.

• Defective socket.

• Fuse has blown.

• Defective extension cord.

• Check to make sure machine is plugged into

a working outlet.

• Check the power cord and reset the GFCI.

Try a dierent outlet.

• Replace fuse. Switch o any other machines

that are using the same circuit.

• Try the unit without an extension cord.

• Check the hoses and connections are airtight.

• Clean or replace valves/seals.

• Please call the Snow Joe® + Sun Joe® customer

service center at 1-866-SNOWJOE (1-866-766-9563)

for assistance.

• Replace fuse. Switch o other machines using

the same circuit.

• Check that the mains voltage corresponds to

specication on the model tag.

• Let the washer cool down for 5 minutes, then restart.

• Clean the nozzle.

• Install a fuse with a higher amp rating than the

amp consumption of the machine. Try the unit

without an extension cord.

• Allow machine to run by holding the trigger until

regular working pressure resumes.

• Check that the water supply corresponds to the

specications required.

• WARNING! Avoid using long, thin hoses

(minimum 1/2 in. diameter).

• Clean the nozzle.

• Clean the water inlet lter.

• Straighten out the hose to remove any kinks/blockages.

• Please call the Snow Joe® + Sun Joe® customer service

center at 1-866-SNOWJOE (1-866-766-9563) for

assistance.

• Wait for pump/hoses or accessories to thaw.

• Connect inlet water.

• Clean the water inlet lter.

• Clean the nozzle.

• Pump sucking air.

• Valves dirty, worn out, or stuck.

• Pump seals worn out.

• Fuse has blown.

• Incorrect mains voltage.

• Thermal sensor activated.

• Nozzle partially blocked.

• Fuse too small.

• Air in inlet hose.

• Inadequate supply of mains water.

• Nozzle partially blocked.

• Water lter blocked.

• Hose kinked.

• Pump/spray gun is leaking.

• Trigger mechanism is broken.

• Pump/hoses or accessories frozen.

• No water supply.

• Water inlet lter blocked.

• Nozzle blocked.

Fluctuating pressure

Machine stops

Fuse blows

Machine pulsating

Machine often starts

and stops by itself

Machine starts, but

no water comes out

Sun Joe’s complete line of premium pressure washer accessories and attachments

make it easy to get your dirty work done, and also help you get the most out of your model!

SHOP ONLINE now at sunjoe.com

NOTE: Accessories are subject to change without any obligation on the part of Snow Joe® + Sun Joe® to provide notice of such

changes. Accessories can be ordered online at sunjoe.com or via phone by contacting the Snow Joe® + Sun Joe® customer

service center at 1-866-SNOWJOE (1-866-766-9563).

Optional Accessories

mWARNING! ALWAYS use only authorized Snow Joe® + Sun Joe® replacement parts and accessories. NEVER use

replacement parts or accessories that are not intended for use with this electric pressure washer. Contact Snow Joe® + Sun Joe®

if you are unsure whether it is safe to use a particular replacement part or accessory with your pressure washer. The use of any

other attachment or accessory can be dangerous and could cause injury or mechanical damage.

25-Foot Medium-duty Extension Hose for

SPX Pressure Washer Series

Solid Brass Universal Quick-Connect Coupler

(Garden Hose to Pressure Washer Adapter)

SPX-25H

SPX-UQC

ModelAccessories Item

Sun Joe® House + Deck All-Purpose Pressure

Washer Rated Concentrated Cleaner SPX-HDC1G

Sun Joe® Premium Snow Foam Pressure

Washer Rated Car Wash Soap + Cleaner SPX-FCS1G

Sun Joe® All-Purpose Heavy Duty Pressure

Washer Rated Cleaner + Degreaser SPX-APC1G

R4_01282020

SNOW JOE® + SUN JOE® CUSTOMER PROMISE

OUR WARRANTY:

Snow Joe warrants new, genuine, powered and non-powered Products to be free from defects in material or workmanship when used

for ordinary household use for a period of two years from the date of purchase by the original, end-user purchaser when purchased

from Snow Joe or from one of Snow Joe’s authorized sellers with proof of purchase. Because Snow Joe is unable to control the quality

of its Products sold by unauthorized sellers, unless otherwise prohibited by law, this Warranty does not cover Products purchased from

unauthorized sellers. If your Product does not work or there’s an issue with a specic part that is covered by the terms of this Warranty,

Snow Joe will elect to either (1) send you a free replacement part, (2) replace the Product with a new or comparable product at no

charge, or (3) repair the Product. How cool is that!

This Warranty gives you speciﬁc legal rights, and you may also have other rights which vary from State to State.

PRODUCT REGISTRATION:

Snow Joe strongly encourages you to register your Product. You can register online at snowjoe.com/register, or by printing and

mailing in a registration card available online from our website, or calling our Customer Service Department at 1-866-SNOWJOE

(1-866-766-9563), or by e-mailing us at [email protected]. Failure to register your Product will not diminish your warranty

rights. However, registering your Product will allow Snow Joe to better serve you with any of your customer service needs.

WHO CAN SEEK LIMITED WARRANTY COVERAGE:

This Warranty is extended by Snow Joe to the original purchaser and original owner of the Product.

WHAT IS NOT COVERED?

This Warranty does not apply if the Product has been used commercially or for non-household or rental applications. This Warranty also

does not apply if the Product was purchased from an unauthorized seller. This Warranty also does not cover cosmetic changes that do

not aect performance. Wearing parts like belts, augers, chains and tines are not covered under this Warranty, and can be purchased

at snowjoe.com or by calling 1-866-SNOWJOE (1-866-766-9563).

ABOVE ALL ELSE, Snow Joe, LLC (“Snow Joe”) is dedicated to you, our customer. We strive to make your experience as pleasant as

possible. Unfortunately, there are times when a Snow Joe®, Sun Joe®, or Aqua Joe® product (“Product”) does not work or breaks under

normal operating conditions. We think it’s important that you know what you can expect from us. That’s why we have a Limited Warranty

(“Warranty”) for our Products.

Una división de Snow Joe®, LLC

MANUAL DEL OPERADOR

Modelo SPX2688-MAX Forma Nº SJ-SPX2688-MAX-880S-M

13 A HIDROLAVADORA ELÉCTRICA

2,050 PSI MÁX. AL MOMENTO DE LA DESCARGA INICIAL SEGÚN PRUEBA DE PRESIÓN INTERNA DE CSA

6.8 L/min MÁX. CON BOQUILLA ABIERTA A MÍNIMA PRESIÓN

¡IMPORTANTE!

Instrucciones de seguridad

Todos los operadores deberán leer

estas instrucciones antes del uso

m ¡ADVERTENCIA! Esto indica una situación peligrosa

que, de no ser evitada, puede resultar en lesiones personales

severas o la muerte.

m ¡PRECAUCIÓN! Esto indica una situación peligrosa

que, de no ser evitada, puede resultar en lesiones personales

menores o moderadas.

m ¡PELIGRO! Esto indica una situación peligrosa que,

de no ser evitada, dará como resultado lesiones personales

severas o la muerte.

Seguridad general

m ¡ADVERTENCIA! Este artefacto no ha sido diseñado

para su uso por niños ni por otras personas sin asistencia

o supervisión cuyas habilidades físicas, sensoriales o

mentales les impidan usarlo de forma segura. Los niños

deben estar bajo supervisión para garantizar que no jueguen

con el artefacto.

Antes de encender su máquina, inspecciónela

cuidadosamente para cerciorarse de que no tenga defectos.

Si encuentra algún defecto, no la encienda. Contacte a

un concesionario autorizado Snow Joe® + Sun Joe® o

comuníquese con la central de servicio al cliente Snow Joe® +

Sun Joe® llamando al 1-866-SNOWJOE (1-866-766-9563).

m ¡ADVERTENCIA! Se deben tomar precauciones

básicas de seguridad siempre que se use esta hidrolavadora

para reducir riesgos de incendio, choque eléctrico y lesiones

personales. Estas precauciones incluyen:

• Conozca su producto: sepa cómo detener la máquina y

purgar la presión de forma rápida. Familiarícese a fondo

con los controles.

• Mantenga alejados a los transeúntes: todas las personas

y mascotas deberán encontrarse a una distancia segura del

área de trabajo.

• Use el producto adecuado: no utilice esta máquina para

ningún otro trabajo excepto para el cual ha sido diseñada.

• Vístase apropiadamente: no utilice prendas holgadas ni

joyería. Pueden llegar a engancharse en las partes móviles.

Al trabajar en exteriores, se recomienda el uso de guantes

de goma y calzado antideslizante.

• m ¡PRECAUCIÓN! Tenga cuidado y evite resbalar o caer.

Utilice calzado protector que proteja sus pies y mejore su

posición de pie en supercies resbaladizas.

• Manténgase alerta: vea lo que está haciendo. Utilice su

sentido común. No opere la hidrolavadora si usted está

cansado o bajo la inuencia del alcohol o las drogas.

• No se extralimite: mantenga con sus pies una posición y

un balance adecuados todo el tiempo.

• Evite encendidos accidentales: no transporte la máquina

enchufada con su dedo sobre el gatillo. Asegúrese de que

el interruptor esté en la posición de apagado antes de

enchufar la unidad.

• No abuse del cable: nunca mueva la máquina tirando de

su cable, ni tire bruscamente de este para desconectar la

máquina del tomacorriente. Mantenga el cable alejado del

calor, aceite y bordes alados.

• Use gafas protectoras: use también calzado protector,

ropa que se ajuste a su cuerpo, guantes protectores y

protección auditiva y para la cabeza.

• Compruebe la temperatura del agua: esta hidrolavadora

no está hecha para bombear agua caliente. NUNCA la

conecte a una fuente de agua caliente, ya que esto reducirá

signicativamente el ciclo de vida útil de la bomba.

• Guárdela en un lugar bajo techo: NUNCA almacene la

hidrolavadora en exteriores o donde pueda congelarse. La

bomba podría dañarse severamente.

• Interruptor de circuito por falla a tierra (GFCI): este

producto incluye un interruptor de circuito por falla a tierra

incorporado al enchufe del cable de alimentación. Si se

necesita reemplazar el enchufe o cable de alimentación,

use solo partes de repuesto idénticas.

• Inspeccione los cables eléctricos: el aislamiento del

cable de alimentación debe estar perfectamente intacto.

Si el cable de alimentación está dañado o hay señales de

desgaste o deterioro, no use esta hidrolavadora. Contacte

a un concesionario autorizado Snow Joe® + Sun Joe® o

comuníquese con la central de servicio al cliente

Snow Joe® + Sun Joe® llamando al 1-866-SNOWJOE

(1-866-766-9563).

m ¡ADVERTENCIA! No use este artefacto sin antes leer

este manual de instrucciones.

m ¡ADVERTENCIA! Este artefacto ha sido diseñado

para su uso con agentes de limpieza recomendados por el

fabricante. El uso de otros agentes de limpieza o químicos

puede afectar de forma negativa la seguridad del artefacto.

m ¡ADVERTENCIA! No use el artefacto cerca de

personas, a menos que estén usando ropa protectora.

m ¡ADVERTENCIA! Los chorros de alta presión pueden

ser peligrosos si se manipulan incorrectamente. El chorro no

deberá estar dirigido a personas, mascotas, equipos eléctricos

activos ni al artefacto en sí.

• No dirija el chorro hacia usted u otras personas para limpiar

ropa o calzado.

• Riesgo de explosión: no rocíe líquidos inamables.

• Desconecte la herramienta: desconecte la hidrolavadora

de la fuente de alimentación antes de llevar a cabo

cualquier tarea de mantenimiento.

• Mantenga alejados a los niños: esta hidrolavadora de

alta presión no debe ser usada por niños ni por personas

no capacitadas.

• Para garantizar un uso seguro del artefacto, use solo partes

de repuesto del fabricante o aprobadas por éste.

m ¡ADVERTENCIA! El agua que ha uido a través de

válvulas contra-reujo se considera no potable.

m ¡ADVERTENCIA! La máquina deberá estar

desconectada de su fuente de alimentación, es decir

desenchufada del tomacorriente, durante la limpieza,

mantenimiento o reemplazo de las partes.

m ¡ADVERTENCIA! Las mangueras, juntas y

acoplamientos de alta presión son importantes para la

seguridad de este artefacto. Use solo mangueras, juntas y

acoplamientos recomendados por el fabricante.

• Inspeccione en busca de partes dañadas: no use el

artefacto si hay daños en el cable de alimentación o en

partes importantes; p. ej., dispositivos de seguridad,

manguera para presión alta o pistola rociadora.

m ¡ADVERTENCIA! Si se usa un cable de extensión, su

enchufe y tomacorriente deben ser a prueba de agua.

m ¡ADVERTENCIA! Los cables de extensión

inadecuados pueden ser peligrosos.

• Esta hidrolavadora de alta presión no debe ser usada a

temperaturas menores de 32°F (0°C).

m ¡ADVERTENCIA! El cable de alimentación debe

estar siempre desenrollado por completo para evitar el

sobrecalentamiento.

• Las conexiones de cables de alimentación deben

permanecer secas y por encima del nivel del suelo.

• Si el cable de alimentación está dañado, no utilice la

hidrolavadora. Contacte a un concesionario autorizado

Snow Joe® + Sun Joe® o comuníquese con la central

de servicio al cliente Snow Joe® + Sun Joe® llamando al

1-866-SNOWJOE (1-866-766-9563).

• Mantenga la máquina en una supercie estable y plana

durante su operación, manipulación, transporte y

almacenamiento. Un volcado repentino de la máquina

puede causar lesiones personales.

• En caso de accidente o desperfecto, desenchufe

la máquina inmediatamente. Si hay contacto con el

detergente, enjuague con abundante agua limpia.

Seguridad eléctrica

ATENCIÓN: si hay problemas con la red eléctrica, pueden

ocurrir caídas breves de voltaje al encender el equipo. Estas a

su vez pueden afectar otros equipos (como por ejemplo, una

lámpara parpadeando). Si la IMPEDANCIA DE LA RED (Zmax)

es menor que 0.335 ohmios, estas uctuaciones no son

esperadas. Si necesita ayuda, puede contactar a su empresa

local de suministro eléctrico para más información.

m ¡ADVERTENCIA! Peligro de choque eléctrico: antes

de encender su hidrolavadora, inspecciónela cuidadosamente

para comprobar que no tenga defectos. Si encuentra algún

defecto, no la encienda y comuníquese con su distribuidor.

Al conectar la hidrolavadora de alta presión a la red eléctrica,

se debe cumplir con lo siguiente:

• La conexión al suministro eléctrico deberá haber sido

hecha por una persona calicada.

• La alimentación de electricidad a este artefacto deberá

incluir ya sea un dispositivo de corriente residual (RCD),

que interrumpirá el suministro si la corriente de fuga a

tierra excede los 30 mA durante 30 ms, o un interruptor de

circuito por falla a tierra (GFCI).

IMPORTANTE: solo use agua sin impurezas. Si hay un

peligro de arena uyendo en el agua de entrada (p. ej., de su

propio pozo), se deberá instalar un ltro adicional.

Dispositivos de seguridad

La pistola rociadora incluye un dispositivo de trabado. Cuando

el dispositivo de trabado está activado, la pistola rociadora no

puede ser operada.

1. Sensor térmico: un sensor térmico protege el motor

contra sobrecargas. Si el sensor térmico se ha activado

y la alimentación ha sido interrumpida, espere unos

minutos hasta que el motor se enfríe para poder re-

encender la unidad.

2. Doble aislamiento: en un artefacto de doble aislamiento,

se proporcionan dos sistemas de aislamiento en

lugar de una conexión a tierra. Un artefacto de doble

aislamiento no posee una conexión a tierra, y no debe

agregársele ninguna. La reparación de un artefacto de

doble aislamiento requiere sumo cuidado y conocimiento

del sistema, y solo debe ser realizada por personal

técnico calicado en un centro de servicio autorizado

La page charge ...

Sun Joe SPX2688-MAX-RM Mode d'emploi

Marque: Sun Joe

Modèle: SPX2688-MAX-RM

Catégorie: Nettoyeurs haute pression

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Sun Joe SPX2688-MAX-RM User guide
español: Sun Joe SPX2688-MAX-RM Guía del usuario