Sun Joe SPX2688-MAX-RM Mode d'emploi

Catégorie
Nettoyeurs haute pression
Taper
Mode d'emploi
© 2021 by Snow Joe®, LLC
All rights reserved. Original instructions. SAVE THESE INSTRUCTIONS
1
EN
A Division of Snow Joe®, LLC
R
OPERATOR’S MANUAL
Model SPX2688-MAX Form No. SJ-SPX2688-MAX-880E-M
13A ELECTRIC PRESSURE WASHER
2050 PSI MAX PRESSURE AT INITIAL DISCHARGE PER CSA INTERNAL PRESSURE TESTING
1.8 GPM MAX FLOW WITH NOZZLE OPEN AT MINIMUM PRESSURE
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
mWARNING! This indicates a hazardous situation, which,
if not avoided, could result in death or serious injury.
mCAUTION! This indicates a hazardous situation, which,
if not avoided, could result in minor or moderate injury.
mDANGER! This indicates a hazardous situation, which,
if not followed, will result in death or serious injury.
General Safety
mWARNING! This appliance is not intended for use
by children or by unassisted, unsupervised persons whose
physical, sensory or mental capabilities prevent them from
using it safely. Children should be supervised to ensure that
they do not play with the appliance.
Before starting up your machine, please check it carefully for
any defects. If you nd any, do not start up your machine.
Contact your authorized Snow Joe® + Sun Joe® dealer or
call the Snow Joe® + Sun Joe® customer service center at
1-866-SNOWJOE (1-866-766-9563).
mWARNING! When using the pressure washer, basic
safety precautions should always be followed to reduce the
risk of re, electric shock, and personal injury. These include:
Know your product – Know how to stop the machine and
bleed pressure quickly. Thoroughly familiarize yourself with
the controls.
Keep bystanders away – All visitors and pets should be
kept a safe distance away from the work area.
Use the right product – Do not use this machine for any
job except that for which it is intended.
Dress properly – Do not wear loose clothing or jewelry.
They can get caught in moving parts. Protective rubber
gloves and non-slip footwear are recommended when
working outdoors.
mCAUTION! – Exercise caution to avoid slipping or falling.
Wear protective footwear that will protect your feet and
improve your footing on slippery surfaces.
Stay alert – Watch what you are doing. Use common
sense. Do not operate the pressure washer when you are
tired, or under the inuence of alcohol or drugs.
Do not overreach – Keep proper footing and balance at
all times.
• Avoid unintentional starting – Do not carry a plugged-
in machine with your nger on the trigger. Make sure the
switch is o before plugging in the machine.
Do not abuse the cord – Never carry the machine by the
cord or yank the cord to disconnect it from the receptacle.
Keep the cord away from heat, oil, and sharp edges.
Use safety glasses – Also use safety footwear, snug-tting
clothing, protective gloves, hearing and head protection.
Check the water temperature – This pressure washer
is not meant to pump hot water. NEVER connect it to a
hot water supply as it will signicantly reduce the life of
the pump.
Store indoors – NEVER store the pressure washer
outdoors or where it could freeze. The pump could be
seriously damaged.
Ground Fault Circuit Interrupter (GFCI) – This product
is provided with a ground fault circuit interrupter built into
the power cord plug. If replacement of the plug or cord is
needed, use only identical replacement parts.
• Inspect electrical cords – The insulation of the power cord
should be perfectly intact. If the power cord is damaged or
shows any signs of wear or tear, do not use the pressure
washer. Contact your authorized Snow Joe® + Sun Joe®
dealer or call the Snow Joe® + Sun Joe® customer service
center at 1-866-SNOWJOE (1-866-766-9563).
mWARNING! Do not use this appliance without reading
this instruction manual.
mWARNING! This appliance has been designed for
use with cleaning agents that are recommended by the
manufacturer. The use of other cleaning agents or chemicals
may adversely aect the safety of the appliance.
mWARNING! Do not use the appliance within range of
persons unless they are wearing protective clothing.
mWARNING! High-pressure jets can be dangerous if
subject to misuse. The jet must not be directed at persons,
pets, live electrical equipment, or the appliance itself.
• Do not direct the jet at yourself or others in order to clean
clothes or footwear.
2
Risk of explosion – Do not spray ammable liquids.
Disconnect the tool – Disconnect from the electrical power
supply before performing any maintenance task.
Keep children away – This high-pressure electric
power washer must not be used by children or
untrained personnel.
• To ensure appliance safety, use only original
replacement parts from the manufacturer or those
approved by the manufacturer.
mWARNING! Water that has owed through backow
preventers is considered to be non-potable.
mWARNING! During cleaning, maintenance or when
replacing parts, the machine must be disconnected from its
power source by removing the plug from the socket outlet.
mWARNING! High-pressure hoses, ttings, and
couplings are important for the safe operation of the
appliance. Use only hoses, ttings, and couplings
recommended by the manufacturer.
Check for damaged parts – Do not use the appliance if
the supply cord or other important parts of the appliance
are damaged (e.g. safety devices, high-pressure hose,
trigger gun).
mWARNING! If an extension cord is used, the plug and
socket must be of watertight construction.
mWARNING! Inadequate extension cords can be
dangerous.
• This high-pressure electric power washer must not be used
at temperatures below 32ºF (0°C).
mWARNING! Power cords on drums should always be
completely unwound to prevent the cord from overheating.
• Power cord connections should be kept dry and o
the ground.
• If the power cord is damaged, do not use the appliance.
Contact your authorized Snow Joe® + Sun Joe® dealer or
call the Snow Joe® + Sun Joe® customer service center at
1-866-SNOWJOE (1-866-766-9563).
• Keep the machine on a stable, at surface during operation,
handling, transportation, and storage. Sudden overturn of
the machine can cause bodily injury.
• In the event of an accident or breakdown, switch o the
machine immediately. (If contact with detergent occurs,
rinse with an abundance of clean water.)
Electrical Safety
ATTENTION: If there are problems with the electrical mains,
short voltage drops may appear when starting the equipment.
This can, in turn, inuence other equipment (e.g. cause a
lamp to blink). If the MAINS-IMPEDANCE Zmax < 0.335 OHM,
such disturbances are not expected (if you require assistance,
contact your local supply authority for further information).
mWARNING! Electrical Shock Hazard – Before starting
up your machine, please check it carefully for any defects.
If you nd any, do not start up your machine and contact
your distributor.
The following should be observed when connecting the
high-pressure electric power washer to the electric supply:
• The electric supply connection should be performed by a
qualied person.
• The electric supply to this appliance should include either
a residual current device that will interrupt the supply if the
leakage current to the earth exceeds 30 mA for 30 ms or a
device that will interrupt the earth circuit (GFCI).
IMPORTANT: Only use water without any impurities.
If there is a risk of running sand into the inlet water (i.e. from
your own well), an additional lter should be installed.
Safety Devices
The spray gun features a locking device. When the lock is
activated, the spray gun cannot be operated.
1. Thermal sensor – A thermal sensor protects the motor
against overloading. If the thermal sensor is activated and
the power is cut o, wait for a while until the motor is cool
and restart the unit.
2. Double insulation – In a double-insulated appliance, two
systems of insulation are provided instead of grounding.
No grounding means is provided on a double-insulated
appliance, nor should a means for grounding be added
to the appliance. Servicing a double-insulated appliance
requires extreme care and knowledge of the system, and
should be performed only by qualied service personnel at
an authorized Snow Joe® + Sun Joe® dealer. Replacement
parts for a double-insulated appliance must be identical
to the parts they replace. A double-insulated appliance
is marked with the words “Double Insulation” or “Double
Insulated.” The symbol (square within a square) may
also be marked on the appliance.
3. Ground fault circuit interrupter (GFCI) protection – This
pressure washer is provided with a ground-fault circuit-
interrupter (GFCI) built into the plug of the power-supply
cord. This device provides additional protection from the
risk of electric shock. Should replacement of the plug or
cord become necessary, use only identical replacement
parts that include GFCI protection.
4. It is not recommended to use an extension cord with this
pressure washer. The unit comes standard with a 35 ft
3
GFCI power cord. Using an extension cord may cause
a drop in line voltage resulting in loss of power
and overheating.
If an extension cord is going to be used, use only
extension cords that are intended for outdoor use. These
extension cords are identied by marking "Acceptable
for use with outdoor appliance; store indoors while not
in use". Use only extension cord having an electrical
rating not less than the rating of the product. Do not use
damaged extension cords. Examine extension cord before
using and replace if damaged. Do not abuse extension
cord and do not yank on any cord to disconnect. Keep
cord away from heat and sharp edges. Always disconnect
extension cord from the receptacle before disconnecting
the product from the extension cord.
5. To reduce the risk of electric shock, this appliance has
a polarized plug (i.e. one blade is wider than the other).
The appliance plug will t into a polarized outlet only
one way.
If the appliance plug does not t fully into the outlet,
reverse the plug. If the plug still does not t, make sure
that you are using the correct polarized wall outlet. If the
plug still does not t, contact a qualied electrician to
install the proper wall outlet. Do not modify the
appliance plug, power cord receptacle, or power cord
plug in any way.
mWARNING! To reduce the risk of electrocution, keep
all connections dry and o the ground. Do not touch plug with
wet hand.
6. To prevent the appliance cord from disconnecting from the
extension cord during operation, make a knot with the two
cords as shown in Table 1.
7. Do not abuse the cord. Never pull the pressure washer
by the cord or yank the cord to disconnect it from the
receptacle. Keep the cord away from heat, oil, and
sharp edges.
Risk of electrocution
• Inspect cord before using.
Do not use if cord is damaged.
• Keep all connections dry and o the ground.
Do not touch plug with wet hands.
Keep cord away from heat and sharp edges.
• Do not spray electrical apparatus and wiring.
Risk of explosion
• Do not spray ammable liquids.
• Do not use acids, bases, solvents, or any ammable
material in this product. These substances can cause
physical injuries to the operator and irreversible damage
to the machine.
Additional safety instructions
• High-pressure: keep clear of nozzle.
• Injection hazard: equipment can cause serious injury if the
spray penetrates the skin.
• Do not point the gun at anyone or at any part of the body.
• In case of skin penetration, seek medical aid immediately.
• Before servicing, cleaning, or removing any parts, shut o
the power and relieve pressure.
• This machine is not suitable for connection to the potable
water mains.
m WARNING m
Electric shock may cause SEVERE INJURY or
DEATH. Heed these warnings:
• Do not allow any part of the electric pressure washer
to make contact with water while it is in operation. If
the appliance becomes wet while turned o, wipe dry
before starting.
• Do not use an extension cord over 25 ft. The
pressure washer comes equipped with a 35 ft power
cable. Combined cord length must not exceed 60 ft.
Any extension cord must be 14-gauge (or heavier) to
safely power the pressure washer.
• Do not touch the appliance or its plug with wet hands
or while standing in water. Wearing rubber boots
oers some protection.
EXTENSION CORD CHART
Cord Length:
Min. Wire Gauge (A.W.G.):
25 ft (7.6 m)
14
(B) Connect plug and receptacle
Cord set Appliance cord
(A) Tie cord as shown
Table 1. Method of Securing Extension Cord
4
Product Description
Purpose
• This electric high pressure washer is intended for residential
use only. It is designed for medium-to-heavy duty cleaning
jobs on boats, motorcycles, RV’s, ATV’s, trailers, decks,
barbecues, siding, patio furniture, and more.
Areas of application
• Never use the machine in potentially explosive areas under
any circumstances!
• The operating temperature must be between 32ºF (0ºC) and
104ºF (40ºC).
• The machine consists of an assembly with a pump,
which is encased in a shock-absorbing housing. To
provide the operator with an optimal working position,
the machine is equipped with a spray wand and a non-slip
handle grip, whose shape and conguration comply with
applicable regulations.
• Do not cover or modify the spray wand or the spray nozzle
in any way.
• The high-pressure electric power washer is designed to be
used with cold or lukewarm water; higher temperatures can
damage the pump.
• Do not use water that is dirty, gritty, or contains any
chemical products, as such impurities could impair
operation and shorten the life of the machine.
5
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the machine before attempting to assemble and operate.
To reduce the risk of injury, user
must keep all bystanders at least
49 ft (15 m) away.
Always keep the power cable
away from heat sources, oils, or
sharp edges. Immediately remove
plug from the mains if the cable is
damaged, frayed, or entangled.
READ THE OPERATOR'S
MANUAL(S) – Read, understand,
and follow all instructions in the
user manual(s) before attempting
to assemble and operate.
SAFETY ALERT – Indicates a
precaution, a warning, or a danger.
WEAR EYE AND HEARING
PROTECTION – For protection
against injury, wear ear defenders
and safety goggles.
Double Insulation – When servicing, use only identical replacement parts.
WARNING! Do not expose the
unit to rain or wet conditions.
Keep dry.
Machine not suitable for connection
to the potable water mains.
WARNING! Electrical shock hazard.
WARNING! Turn the machine OFF
and disconnect it from the power
supply before inspecting, cleaning,
changing accessories, or conducting
any other maintenance task.
Symbols SymbolsDescriptions Descriptions
Wear non-slip footwear that will
protect your feet and improve your
footing on slippery surfaces.
Wear safety gloves during
use to protect hands.
Store indoors. Never store the
pressure washer outdoors.
If the pump freezes, permanent
damage may result.
6
Know Your Electric Pressure Washer
Read the owner’s manual and safety rules carefully before operating the pressure washer. Compare the illustration below
to the unit in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for
future reference.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1. Trigger gun
2. On/O switch
3. Water outlet/high-pressure hose
connection
4. Garden hose adapter/
connection
5. Power cord with GFCI
6. Wheels (2)
7. Needle clean-out tool
8. Cord holder
9. Top handle
10. High-pressure hose holder
11. High-pressure hose
12. On-board nozzle storage
13. 0º Quick-Connect nozzle (red)
14. 15º Quick-Connect nozzle (yellow)
15. 40º Quick-Connect nozzle (gray)
16. Foam adjusting cap
17. Detergent nozzle
18. Foam cannon bottle
19. Spray wand protector
20. Brass quick-connect collar
21. Spray wand
22. Trigger gun holder
23. High-pressure hose connection
24. Trigger
25. Safety lock
7
Technical Data
Rated Voltage ...................................................... 120V ~ 60 Hz
Motor ............................................................................ 13-amp
Max Water Inlet Temperature ................................. 104ºF/40ºC
Max Water Inlet Pressure ............................................ 0.7 MPa
Foam Cannon Capacity ...................................... 33.8  oz (1 L)
High Pressure Hose Length ....................................... 20 ft (6 m)
Power Cord Length .............................................. 35 ft (10.7 m)
Max Pressure at initial discharge ................................ 2050 PSI
per CSA internal pressure testing
Rated Pressure under typical load .............................. 1600 PSI
Max Flow with nozzle open ....................... 1.8 GPM (6.8 L/min)
at minimum pressure
Rated Flow under typical load ................... 1.1 GPM (4.2 L/min)
Net Weight ....................................................... 15.8 lbs (7.2 kg)
Unpacking
Carton Contents
Electric pressure washer
Top handle
High-pressure hose holder
Spray wand protector
Trigger gun holder
Cord holder
• 4.8 x 16 screws (7)
Spray wand
Trigger gun
• Three (3) Quick-Connect nozzles (0º, 15º, 40º)
Needle clean-out tool (included with manual packet)
High-pressure hose
• Garden hose adapter (female coupler)
Manual with registration card
1. Carefully remove the pressure washer and check to see
that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or
damage occurred during shipping. If you nd damaged or
missing parts, DO NOT return the unit to the store. Please
call the Snow Joe® + Sun Joe® customer service center at
1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton and packaging
material until you are ready to use your new electric
pressure washer. The packaging is made of recyclable
materials. Properly dispose of these materials in
accordance with local regulations.
IMPORTANT! The equipment and packaging material are
not toys. Do not let children play with plastic bags, foils,
or small parts. These items can be swallowed and pose a
suocation risk!
mWARNING! Do not connect to power supply until
assembly is complete. Failure to comply could result in
accidental starting and possible serious personal injury.
Assembly
Tools required: Phillips head screwdriver
1. Slide the top handle in position on the top of the pressure
washer, and attach using the three screws as shown
(Fig. 1).
2. Attach the high-pressure hose holder and secure using the
four additional screws provided, as shown (Fig. 2).
3. Slide the cord holder into position (Fig. 3).
Fig. 1
Top handle
Screws
Screw
Fig. 2
High-pressure
hose holder Fix with
4 screws
8
4. Slide the trigger gun holder into position (Fig. 4).
5. Slide the spray wand protector into position (Fig. 5).
6. To connect the spray wand with the trigger gun, press
the wings of the spray wand into the slot of the trigger
gun, then twist counterclockwise until the 2 parts are
completely locked together (Fig. 6).
7. Connect the high-pressure hose to the trigger gun. Twist
to secure the connection (Fig. 7).
8. Connect the other end of high-pressure hose to the water
outlet on the washer and tighten securely (Fig. 8).
Fig. 3
Cord holder
Fig. 4
Trigger gun
holder
Fig. 5
Spray wand
protector
Trigger gun
Spray wand
Fig. 6
Spray wand wings
Fig. 7
High pressure hose
Trigger gun
Fig. 8
Water outletHigh-pressure
hose
9
mWARNING! Keep hose away from sharp objects.
Bursting hoses may cause injury. Examine hoses regularly and
replace if damaged. Do not attempt to mend a damaged hose.
9. Connect the garden hose adapter (female coupler) to
the water inlet of the pressure washer, then thread your
garden hose (male end) into the garden hose adapter
(Fig. 9). The garden hose must have an internal
diameter of at least 13 mm (1/2 in.) and must be
reinforced. The water supply must be at least equal to the
washer delivery capacity.
NOTE: The machine is not suitable for connection to the
potable water main.
10. Attach garden hose to water supply (Fig. 10).
mWARNING! Do not connect to potable water system.
mWARNING! If connection is made to a potable water
system, the system shall be protected against backow.
mWARNING! The intake water temperature must not
exceed 104ºF/40ºC. The water supply must not exceed
0.7 MPa.
mCAUTION! The washer must only be used with clean
water; use of unltered water containing corrosive chemicals
will damage the washer.
mCAUTION! To prevent damage to the appliance, do not
allow it to operate dry. Before starting the appliance, make
sure that it has proper and stable supply of water.
Operation
Using the Pressure Washer
mIMPORTANT! This pressure washer is equipped with
a micro-switch sensitive to water ow. This Total Stop System
(TSS) senses water ow in the pump. When the trigger is
released, water stops owing through the pump. The TSS then
automatically turns the motor o to protect the pump from
overheating, thus saving energy and prolonging pump life.
1. Position the washer as CLOSE as possible to the
water supply.
2. The washer must be used on a secure and stable surface
in a standing, upright position (Fig. 11).
3. Make sure the unit is switched o before plugging the unit
into the power outlet.
4. Check that the electrical supply voltage and frequency
(Volt/Hz) correspond to those specied on the rating plate.
If the power supply is correct, you may now plug the
pressure washer into the power outlet (Fig. 12).
R
Fig. 9
Garden hose
This end to
water inlet
Garden hose
(male end)
Water inlet
Fig. 10
Connect to water supply
Garden hose
Fig. 11
RESET
TEST
Fig. 12
GFCI
Reset
10
NOTE: The GFCI may need to be reset when rst plugged
into the electric outlet. Press the "Reset" button until
the power light indicator on the GFCI illuminates when
plugged in.
5. Turn the water supply tap on completely.
6. Release the safety lock, then press the trigger for a few
seconds until the water ow is steady. Operating the
pressure washer in this manner will allow air to escape
and discharge residual pressure in the hose (Figs. 13 – 14).
7. Turn the ON/OFF switch to the ON (I) position to start the
pressure washer (Fig. 15).
Fig. 15
ON/OFF switch
8. When re-starting the motor, always keep the trigger
pressed.
NOTE: The motor only runs when the trigger is operated
and shuts o when the trigger is released.
Using Nozzles
Before beginning any cleaning task, determine the best nozzle
for the job. Each of the nozzles has a dierent spray pattern.
The nozzle patterns are 40˚ (for gentle cleaning), 15˚ (for tough
jobs), and 0˚ (for spot cleaning or hard-to-reach areas) .
mCAUTION! NEVER change nozzles without locking the
safety lock on the trigger handle.
mWARNING! High-pressure jets can be dangerous if
subject to misuse. The jet must not be directed at persons,
pets, live electrical equipment, or the appliance itself.
This electric pressure washer is equipped with three (3) Quick-
Connect nozzles that easily snap onto the Quick-Connect
collar of the spray wand.
To connect a nozzle to the spray wand:
1. Turn o the pressure washer and shut o the water supply.
Pull the trigger to release water pressure.
2. Engage the safety lock on the trigger handle.
3. Pull back the brass Quick-Connect collar and insert the
desired nozzle into the collar. Release the collar and the
nozzle will click into place (Fig. 16).
Fig. 13
Safety lock
Fig. 14
Trigger
11
To disconnect a nozzle from the spray wand once the cleaning
job is complete:
1. Turn o the pressure washer and shut o the water supply.
Pull the trigger to release water pressure.
2. Engage the safety lock on the trigger handle.
3. Remove the nozzle by disconnecting it while pulling back
the brass Quick-Connect collar.
mWARNING! Do not make changes to the nozzle while
the trigger is engaged. Doing so could result in damage to the
pressure washer or injury to the user.
Working with Detergents
When cleaning with the pressure washer, some cleaning tasks
can be solved with water alone, but for most tasks cleaning
with detergent allows for more eective dirt removal.
mWARNING! Use only detergents specically designed
for use with pressure washers, such as Sun Joe® HOUSE +
DECK WASH (SPX-HDC1G), Sun Joe® SNOW FOAM AUTO
WASH (SPX-FCS1G), or Sun Joe® HEAVY DUTY CLEANER
(SPX-APC1G). DO NOT USE household detergents, acids,
alkaline solutions, bleaches, solvents, ammable material,
or industrial grade solutions. These could damage the
pressure washer. Many detergents may require mixing prior
to use. Prepare the cleaning solution as instructed on the
solution bottle.
1. Gently pull the foam cannon bottle out of its storage
position (Fig. 17).
2. Remove the cap. Fill the bottle or mix as recommended by
detergent instructions (Fig. 18), and replace it back on the
unit. Secure the cap back into place.
3. Disconnect the spray wand from the trigger gun by
pressing it in rmly and twisting clockwise until the 2
wings of the spray wand can be removed from the slot
(Fig. 19).
Fig. 16
Spray wand quick-
connect collar
Nozzle
Pull back
Fig. 17
Foam
cannon
bottle
Fig. 18
Detergent
for pressure
washer
Foam cannon bottle
Fig. 19
Press the spray
wand inside
1
Twist the spray
wand as shown
2
12
4. To connect the foam cannon with the trigger gun, press
the wings of the foam cannon into the slot of the trigger
gun, then twist until the 2 parts are completely locked
(Fig. 20).
5. Turn on the pressure washer. Pull the trigger to operate the
unit. The liquid detergent will automatically mix with water
and be discharged through the nozzle.
NOTE: The spray angle can be adjusted from 0° to 45° by
rotating the foam cannon nozzle. The foam volume can
be adjusted by rotating the adjustable cap, as indicated
below (Fig. 21).
mWARNING! Do not adjust the foam cannon while the
trigger is squeezed. Failure to do so could result in damage.
mCAUTION! Always test the detergent in an
inconspicuous area before use.
6. Apply detergent from the bottom to the top of the dry
surface to be cleaned.
NOTE: Wetting the surface rst is not recommended as it
dilutes the detergent and reduces its cleaning ability.
7. Allow the detergent to remain on the surface for a short
time before rinsing. Do not allow the detergent to dry on
the surface.
mCAUTION! Damage may occur to painted surfaces if
the detergent is allowed to dry on the surface. Wash and rinse
a small section at a time. Avoid working on hot surfaces or in
direct sunlight.
8. When nished using the pressure washer, you must rst
drain and rinse the foam cannon bottle. Run the pressure
washer until all of the soap is drained from the foam
cannon bottle.
mCAUTION! Failure to follow these cleaning instructions
will cause the injection system to become clogged and
inoperable.
mIMPORTANT! NEVER USE:
Bleach, chlorine products, and other corrosive chemicals
Liquids containing solvents
(e.g. paint thinners, gasoline, oils)
Tri-sodium phosphate products
Ammonia products
Acid-based products
These chemicals will harm the unit and will damage
the cleaning surface.
Shutting down
1. Turn the switch to the OFF (0) position and unplug the
power cord from the outlet.
2. Turn o the water source.
3. Hold the trigger to release water pressure.
4. Disconnect the garden hose from the water inlet on
the unit.
5. Disconnect the high-pressure hose connection on the
trigger gun handle.
6. Release the trigger and engage the gun safety lock.
mWARNING! Turn o the water supply and squeeze the
trigger to depressurize the unit. Failure to do so could result in
personal injury due to discharge of high-pressure water.
Taking a break
If you are taking a break of ve minutes or more between
cleaning tasks:
1. Engage the gun safety lock on the back.
2. Turn the switch to the OFF (0) position.
3. Unplug the power cord from the outlet.
Fig. 20
Trigger gunFoam cannon
Foam cannon
wings
Fig. 21
Adjustable cap
Decrease soap
volume
Increase soap
volume
Adjustable
nozzle
Pencil jet Fan spray
13
Storage
mCAUTION! Always store your pressure washer in a
location where the temperature will not fall below 32ºF (0ºC).
The pump in this machine is susceptible to permanent damage
if it freezes. FREEZE DAMAGE IS NOT COVERED BY THE
WARRANTY.
Store the pressure washer indoors in a dry, covered area
where it is not subject to adverse weather conditions.
It is important to store this product in a frost-free area.
Always empty water from the hoses, the pump, and the
foam cannon bottle (if using) before storing.
mCAUTION! The use of a pump protector is
recommended to prevent cold weather damage during storage
over the winter months.
Winterizing + long-term storage
If you must store your pressure washer in a location where
the temperature falls below 32ºF (0ºC), you can minimize the
chance of damage to your machine by utilizing the following
procedure:
Disconnect all water connections.
Turn on the pressure washer for a few seconds until the
remaining water in the pump exits. Turn o immediately.
Do not allow the high-pressure hose to become kinked.
Store the machine and accessories in a room that does
not reach freezing temperatures.
Do not store near a furnace or other sources of heat that
may dry out the pump seals.
Operate the pressure washer with non-corrosive/non-toxic
anti-freeze, a pump saver, or a pump protector before
storing for the winter.
mWARNING! Before reusing, completely ush the
unit out with clear water. Anti-freeze products can damage
paintwork, so you must ensure there is no anti-freeze left in the
system before using it again.
Maintenance
mCAUTION! Before working on the pressure washer,
disconnect the plug from the power supply socket.
Clean the Adapter Filter and the Nozzle
1. To ensure good performance, check and clean the adapter
lter (Fig. 22). Remove the lter and rinse with warm water
to prevent any foreign matter from clogging the pump
(Fig. 23).
2. Clean the nozzle with the needle clean-out tool provided
(Fig. 24). Remove the nozzle from the spray wand; remove
any dirt from the nozzle hole and rinse.
Fig. 22
Adapterlter
Garden hose
adapter
Fig. 23
Filter
15º
Fig. 24
Needle clean-out tool
14
Disposal
Recycling the Pressure Washer
Do not dispose of electrical appliances as unsorted
municipal waste. Use separate collection facilities.
Contact your local government agency for information
regarding the collection systems available.
If electrical appliances are disposed of in landlls
or dumps, hazardous substances can leak into the
groundwater and get into the food chain, damaging your
health and well-being.
Service + Support
If your Sun Joe® SPX2688-MAX electric pressure washer
requires service or maintenance, please call the Snow Joe® +
Sun Joe® customer service center at 1-866-SNOWJOE
(1-866-766-9563).
Model + Serial Numbers
When contacting the company, reordering parts, or arranging
service from an authorized dealer, you will need to provide the
model and serial numbers, which can be found on the decal
located on the housing of the unit. Copy these numbers into
the space provided below.
S P X 2 6 8 8 - M A X
Record the following numbers from the housing or handle of your
new product:
Model #:
Serial #:
15
Troubleshooting
• Disconnect the unit from the electrical power supply before carrying out maintenance on the machine or when checking that
its parts are in proper working order.
• To avoid unnecessary hassles, consult the following table before contacting customer service with any mechanical issues.
Problems Possible Cause Possible Solution
Machine refuses
to start
Power failure/machine not
plugged into a working receptacle.
Defective socket.
Fuse has blown.
Defective extension cord.
Check to make sure machine is plugged into
a working outlet.
Check the power cord and reset the GFCI.
Try a dierent outlet.
Replace fuse. Switch o any other machines
that are using the same circuit.
Try the unit without an extension cord.
Check the hoses and connections are airtight.
Clean or replace valves/seals.
Please call the Snow Joe® + Sun Joe® customer
service center at 1-866-SNOWJOE (1-866-766-9563)
for assistance.
Replace fuse. Switch o other machines using
the same circuit.
Check that the mains voltage corresponds to
specication on the model tag.
Let the washer cool down for 5 minutes, then restart.
Clean the nozzle.
Install a fuse with a higher amp rating than the
amp consumption of the machine. Try the unit
without an extension cord.
Allow machine to run by holding the trigger until
regular working pressure resumes.
Check that the water supply corresponds to the
specications required.
WARNING! Avoid using long, thin hoses
(minimum 1/2 in. diameter).
Clean the nozzle.
Clean the water inlet lter.
Straighten out the hose to remove any kinks/blockages.
Please call the Snow Joe® + Sun Joe® customer service
center at 1-866-SNOWJOE (1-866-766-9563) for
assistance.
Wait for pump/hoses or accessories to thaw.
Connect inlet water.
Clean the water inlet lter.
Clean the nozzle.
Pump sucking air.
Valves dirty, worn out, or stuck.
Pump seals worn out.
Fuse has blown.
Incorrect mains voltage.
Thermal sensor activated.
Nozzle partially blocked.
Fuse too small.
Air in inlet hose.
Inadequate supply of mains water.
Nozzle partially blocked.
Water lter blocked.
Hose kinked.
Pump/spray gun is leaking.
Trigger mechanism is broken.
Pump/hoses or accessories frozen.
No water supply.
Water inlet lter blocked.
Nozzle blocked.
Fluctuating pressure
Machine stops
Fuse blows
Machine pulsating
Machine often starts
and stops by itself
Machine starts, but
no water comes out
16
Sun Joe’s complete line of premium pressure washer accessories and attachments
make it easy to get your dirty work done, and also help you get the most out of your model!
SHOP ONLINE now at sunjoe.com
NOTE: Accessories are subject to change without any obligation on the part of Snow Joe® + Sun Joe® to provide notice of such
changes. Accessories can be ordered online at sunjoe.com or via phone by contacting the Snow Joe® + Sun Joe® customer
service center at 1-866-SNOWJOE (1-866-766-9563).
Optional Accessories
mWARNING! ALWAYS use only authorized Snow Joe® + Sun Joe® replacement parts and accessories. NEVER use
replacement parts or accessories that are not intended for use with this electric pressure washer. Contact Snow Joe® + Sun Joe®
if you are unsure whether it is safe to use a particular replacement part or accessory with your pressure washer. The use of any
other attachment or accessory can be dangerous and could cause injury or mechanical damage.
25-Foot Medium-duty Extension Hose for
SPX Pressure Washer Series
Solid Brass Universal Quick-Connect Coupler
(Garden Hose to Pressure Washer Adapter)
SPX-25H
SPX-UQC
ModelAccessories Item
2
1
3
Sun Joe® House + Deck All-Purpose Pressure
Washer Rated Concentrated Cleaner SPX-HDC1G
Sun Joe® Premium Snow Foam Pressure
Washer Rated Car Wash Soap + Cleaner SPX-FCS1G
Sun Joe® All-Purpose Heavy Duty Pressure
Washer Rated Cleaner + Degreaser SPX-APC1G
R4_01282020
SNOW JOE® + SUN JOE® CUSTOMER PROMISE
OUR WARRANTY:
Snow Joe warrants new, genuine, powered and non-powered Products to be free from defects in material or workmanship when used
for ordinary household use for a period of two years from the date of purchase by the original, end-user purchaser when purchased
from Snow Joe or from one of Snow Joe’s authorized sellers with proof of purchase. Because Snow Joe is unable to control the quality
of its Products sold by unauthorized sellers, unless otherwise prohibited by law, this Warranty does not cover Products purchased from
unauthorized sellers. If your Product does not work or there’s an issue with a specic part that is covered by the terms of this Warranty,
Snow Joe will elect to either (1) send you a free replacement part, (2) replace the Product with a new or comparable product at no
charge, or (3) repair the Product. How cool is that!
This Warranty gives you specific legal rights, and you may also have other rights which vary from State to State.
PRODUCT REGISTRATION:
Snow Joe strongly encourages you to register your Product. You can register online at snowjoe.com/register, or by printing and
mailing in a registration card available online from our website, or calling our Customer Service Department at 1-866-SNOWJOE
(1-866-766-9563), or by e-mailing us at [email protected]. Failure to register your Product will not diminish your warranty
rights. However, registering your Product will allow Snow Joe to better serve you with any of your customer service needs.
WHO CAN SEEK LIMITED WARRANTY COVERAGE:
This Warranty is extended by Snow Joe to the original purchaser and original owner of the Product.
WHAT IS NOT COVERED?
This Warranty does not apply if the Product has been used commercially or for non-household or rental applications. This Warranty also
does not apply if the Product was purchased from an unauthorized seller. This Warranty also does not cover cosmetic changes that do
not aect performance. Wearing parts like belts, augers, chains and tines are not covered under this Warranty, and can be purchased
at snowjoe.com or by calling 1-866-SNOWJOE (1-866-766-9563).
ABOVE ALL ELSE, Snow Joe, LLC (“Snow Joe”) is dedicated to you, our customer. We strive to make your experience as pleasant as
possible. Unfortunately, there are times when a Snow Joe®, Sun Joe®, or Aqua Joe® product (“Product”) does not work or breaks under
normal operating conditions. We think it’s important that you know what you can expect from us. That’s why we have a Limited Warranty
(“Warranty”) for our Products.
17
EN
SP
© 2021 Snow Joe®, LLC
Derechos reservados. Instrucciones originales. GUARDE ESTAS INSTRUCCIONES
19
Una división de Snow Joe®, LLC
R
MANUAL DEL OPERADOR
Modelo SPX2688-MAX Forma Nº SJ-SPX2688-MAX-880S-M
13 A HIDROLAVADORA ELÉCTRICA
2,050 PSI MÁX. AL MOMENTO DE LA DESCARGA INICIAL SEGÚN PRUEBA DE PRESIÓN INTERNA DE CSA
6.8 L/min MÁX. CON BOQUILLA ABIERTA A MÍNIMA PRESIÓN
¡IMPORTANTE!
Instrucciones de seguridad
Todos los operadores deberán leer
estas instrucciones antes del uso
m ¡ADVERTENCIA! Esto indica una situación peligrosa
que, de no ser evitada, puede resultar en lesiones personales
severas o la muerte.
m ¡PRECAUCIÓN! Esto indica una situación peligrosa
que, de no ser evitada, puede resultar en lesiones personales
menores o moderadas.
m ¡PELIGRO! Esto indica una situación peligrosa que,
de no ser evitada, dará como resultado lesiones personales
severas o la muerte.
Seguridad general
m ¡ADVERTENCIA! Este artefacto no ha sido diseñado
para su uso por niños ni por otras personas sin asistencia
o supervisión cuyas habilidades físicas, sensoriales o
mentales les impidan usarlo de forma segura. Los niños
deben estar bajo supervisión para garantizar que no jueguen
con el artefacto.
Antes de encender su máquina, inspecciónela
cuidadosamente para cerciorarse de que no tenga defectos.
Si encuentra algún defecto, no la encienda. Contacte a
un concesionario autorizado Snow Joe® + Sun Joe® o
comuníquese con la central de servicio al cliente Snow Joe® +
Sun Joe® llamando al 1-866-SNOWJOE (1-866-766-9563).
m ¡ADVERTENCIA! Se deben tomar precauciones
básicas de seguridad siempre que se use esta hidrolavadora
para reducir riesgos de incendio, choque eléctrico y lesiones
personales. Estas precauciones incluyen:
Conozca su producto: sepa cómo detener la máquina y
purgar la presión de forma rápida. Familiarícese a fondo
con los controles.
Mantenga alejados a los transeúntes: todas las personas
y mascotas deberán encontrarse a una distancia segura del
área de trabajo.
Use el producto adecuado: no utilice esta máquina para
ningún otro trabajo excepto para el cual ha sido diseñada.
Vístase apropiadamente: no utilice prendas holgadas ni
joyería. Pueden llegar a engancharse en las partes móviles.
Al trabajar en exteriores, se recomienda el uso de guantes
de goma y calzado antideslizante.
m ¡PRECAUCIÓN! Tenga cuidado y evite resbalar o caer.
Utilice calzado protector que proteja sus pies y mejore su
posición de pie en supercies resbaladizas.
Manténgase alerta: vea lo que está haciendo. Utilice su
sentido común. No opere la hidrolavadora si usted está
cansado o bajo la inuencia del alcohol o las drogas.
No se extralimite: mantenga con sus pies una posición y
un balance adecuados todo el tiempo.
Evite encendidos accidentales: no transporte la máquina
enchufada con su dedo sobre el gatillo. Asegúrese de que
el interruptor esté en la posición de apagado antes de
enchufar la unidad.
No abuse del cable: nunca mueva la máquina tirando de
su cable, ni tire bruscamente de este para desconectar la
máquina del tomacorriente. Mantenga el cable alejado del
calor, aceite y bordes alados.
Use gafas protectoras: use también calzado protector,
ropa que se ajuste a su cuerpo, guantes protectores y
protección auditiva y para la cabeza.
Compruebe la temperatura del agua: esta hidrolavadora
no está hecha para bombear agua caliente. NUNCA la
conecte a una fuente de agua caliente, ya que esto reducirá
signicativamente el ciclo de vida útil de la bomba.
Guárdela en un lugar bajo techo: NUNCA almacene la
hidrolavadora en exteriores o donde pueda congelarse. La
bomba podría dañarse severamente.
Interruptor de circuito por falla a tierra (GFCI): este
producto incluye un interruptor de circuito por falla a tierra
incorporado al enchufe del cable de alimentación. Si se
necesita reemplazar el enchufe o cable de alimentación,
use solo partes de repuesto idénticas.
• Inspeccione los cables eléctricos: el aislamiento del
cable de alimentación debe estar perfectamente intacto.
Si el cable de alimentación está dañado o hay señales de
desgaste o deterioro, no use esta hidrolavadora. Contacte
a un concesionario autorizado Snow Joe® + Sun Joe® o
comuníquese con la central de servicio al cliente
Snow Joe® + Sun Joe® llamando al 1-866-SNOWJOE
(1-866-766-9563).
m ¡ADVERTENCIA! No use este artefacto sin antes leer
este manual de instrucciones.
m ¡ADVERTENCIA! Este artefacto ha sido diseñado
para su uso con agentes de limpieza recomendados por el
20
fabricante. El uso de otros agentes de limpieza o químicos
puede afectar de forma negativa la seguridad del artefacto.
m ¡ADVERTENCIA! No use el artefacto cerca de
personas, a menos que estén usando ropa protectora.
m ¡ADVERTENCIA! Los chorros de alta presión pueden
ser peligrosos si se manipulan incorrectamente. El chorro no
deberá estar dirigido a personas, mascotas, equipos eléctricos
activos ni al artefacto en sí.
• No dirija el chorro hacia usted u otras personas para limpiar
ropa o calzado.
Riesgo de explosión: no rocíe líquidos inamables.
Desconecte la herramienta: desconecte la hidrolavadora
de la fuente de alimentación antes de llevar a cabo
cualquier tarea de mantenimiento.
Mantenga alejados a los niños: esta hidrolavadora de
alta presión no debe ser usada por niños ni por personas
no capacitadas.
• Para garantizar un uso seguro del artefacto, use solo partes
de repuesto del fabricante o aprobadas por éste.
m ¡ADVERTENCIA! El agua que ha uido a través de
válvulas contra-reujo se considera no potable.
m ¡ADVERTENCIA! La máquina deberá estar
desconectada de su fuente de alimentación, es decir
desenchufada del tomacorriente, durante la limpieza,
mantenimiento o reemplazo de las partes.
m ¡ADVERTENCIA! Las mangueras, juntas y
acoplamientos de alta presión son importantes para la
seguridad de este artefacto. Use solo mangueras, juntas y
acoplamientos recomendados por el fabricante.
Inspeccione en busca de partes dañadas: no use el
artefacto si hay daños en el cable de alimentación o en
partes importantes; p. ej., dispositivos de seguridad,
manguera para presión alta o pistola rociadora.
m ¡ADVERTENCIA! Si se usa un cable de extensión, su
enchufe y tomacorriente deben ser a prueba de agua.
m ¡ADVERTENCIA! Los cables de extensión
inadecuados pueden ser peligrosos.
• Esta hidrolavadora de alta presión no debe ser usada a
temperaturas menores de 32°F (0°C).
m ¡ADVERTENCIA! El cable de alimentación debe
estar siempre desenrollado por completo para evitar el
sobrecalentamiento.
• Las conexiones de cables de alimentación deben
permanecer secas y por encima del nivel del suelo.
• Si el cable de alimentación está dañado, no utilice la
hidrolavadora. Contacte a un concesionario autorizado
Snow Joe® + Sun Joe® o comuníquese con la central
de servicio al cliente Snow Joe® + Sun Joe® llamando al
1-866-SNOWJOE (1-866-766-9563).
• Mantenga la máquina en una supercie estable y plana
durante su operación, manipulación, transporte y
almacenamiento. Un volcado repentino de la máquina
puede causar lesiones personales.
• En caso de accidente o desperfecto, desenchufe
la máquina inmediatamente. Si hay contacto con el
detergente, enjuague con abundante agua limpia.
Seguridad eléctrica
ATENCIÓN: si hay problemas con la red eléctrica, pueden
ocurrir caídas breves de voltaje al encender el equipo. Estas a
su vez pueden afectar otros equipos (como por ejemplo, una
lámpara parpadeando). Si la IMPEDANCIA DE LA RED (Zmax)
es menor que 0.335 ohmios, estas uctuaciones no son
esperadas. Si necesita ayuda, puede contactar a su empresa
local de suministro eléctrico para más información.
m ¡ADVERTENCIA! Peligro de choque eléctrico: antes
de encender su hidrolavadora, inspecciónela cuidadosamente
para comprobar que no tenga defectos. Si encuentra algún
defecto, no la encienda y comuníquese con su distribuidor.
Al conectar la hidrolavadora de alta presión a la red eléctrica,
se debe cumplir con lo siguiente:
• La conexión al suministro eléctrico deberá haber sido
hecha por una persona calicada.
• La alimentación de electricidad a este artefacto deberá
incluir ya sea un dispositivo de corriente residual (RCD),
que interrumpirá el suministro si la corriente de fuga a
tierra excede los 30 mA durante 30 ms, o un interruptor de
circuito por falla a tierra (GFCI).
IMPORTANTE: solo use agua sin impurezas. Si hay un
peligro de arena uyendo en el agua de entrada (p. ej., de su
propio pozo), se deberá instalar un ltro adicional.
Dispositivos de seguridad
La pistola rociadora incluye un dispositivo de trabado. Cuando
el dispositivo de trabado está activado, la pistola rociadora no
puede ser operada.
1. Sensor térmico: un sensor térmico protege el motor
contra sobrecargas. Si el sensor térmico se ha activado
y la alimentación ha sido interrumpida, espere unos
minutos hasta que el motor se enfríe para poder re-
encender la unidad.
2. Doble aislamiento: en un artefacto de doble aislamiento,
se proporcionan dos sistemas de aislamiento en
lugar de una conexión a tierra. Un artefacto de doble
aislamiento no posee una conexión a tierra, y no debe
agregársele ninguna. La reparación de un artefacto de
doble aislamiento requiere sumo cuidado y conocimiento
del sistema, y solo debe ser realizada por personal
técnico calicado en un centro de servicio autorizado
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Sun Joe SPX2688-MAX-RM Mode d'emploi

Catégorie
Nettoyeurs haute pression
Taper
Mode d'emploi