Glacier Bay 67536-1001 Guide d'installation

Catégorie
Articles sanitaires
Taper
Guide d'installation
THANK YOU
INSTALLATION AND CARE GUIDE
We appreciate the trust and condence you have placed in Glacier Bay through the purchase of this kitchen
faucet. We strive to continually create quality products designed to enhance your home. Visit us online to see
our full line of products available for your home improvement needs. Thank you for choosing Glacier Bay!
PULL-DOWN KITCHEN FAUCET
Questions, problems, missing parts?
Before returning to the store, call Glacier Bay Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday
9 a.m. - 6 p.m., EST, Saturday
1-855-HD-GLACIER (1-855-434-5224)
HOMEDEPOT.COM
YOW 10/2014REV.01
Model#
SKU#
67536-1001
67536-1008D2
67536-1027H2
682-892
665-466
682-894
2
Table of Contents
Important Information ..............................2
Warranty ...................................................2
Pre-Installation .........................................2
Planning Installation ..............................2
Package Contents ..................................3
Installation ................................................4
Operation ..................................................12
Troubleshooting ......................................14
Care and Cleaning
...................................
13
Service Parts
...........................................
16
Adjustable
wrench
Safety
goggles
Phillips
screwdriver
SILICONE
Silicone
sealant
6mm
diameter
Electric
drill
Tools and Hardware Required ...............2
Important Information
Observe all local plumbing and building codes.
Cover the sink drain to avoid losing any parts.
Review the care and cleaning section included in this guide.
Warranty
LIMITED LIFETIME WARRANTY
Glacier Bay products are manufactured with superior quality standards and workmanship and are backed by our
limited lifetime warranty. Glacier Bay products are warranted to the original consumer purchaser to be free of
defects in materials or workmanship. We will replace FREE OF CHARGE any product or parts that proves defective.
Sensor mechanism and LED light excluded from Limited Lifetime Warranty and are covered by a 3-year warranty
from date of purchase. Simply, return the product / part to any of The Home Depot retail locations or call 1-855-HD-
GLACIER (1-855-434-5224) to receive the replacement item. Proof of purchase (original sales receipt) from the
original consumer purchaser must be made available for all Glacier Bay warranty claims.
This warranty excludes incidental/inconsequential damages and failures due to misuse, abuse or normal wear and
tear. This warranty excludes all industrial, commercial & business usage, whose purchasers are hereby, extended
a ve year limited warranty from the date of purchase, with all other terms of this warranty applying except the
duration of warranty.
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations may not apply to you. This warranty gives you specic legal rights and you may also have other
rights that vary from state to state and province to province. Please see a store or contact 1-855-HD-GLACIER for
more details.
Pre-Installation
PLANNING INSTALLATION
Before beginning the installation of this product, ensure all parts are present. Compare parts with the Package
Contents list. If any part is missing or damaged, do not attempt to install the product. Contact customer service
for replacement parts
TOOLS AND HARDWARE REQUIRED
Channel
lock pliers
3
Pre-Installation (continued)
PACKAGE CONTENTS
Part Description Quantity
A 1Faucet body
B 1
C Metal washer 1
Rubber washer
D 1
E Protective cap 1
Nut
H 2
IGasket 1
Bolt
FWrench 1
G Escutcheon 1
LWeight clip 1
JMounting nut 2
K 1Hose & Sprayhead
Part Description Quantity
MWeight 1
NQuick connect
assembly 1
O 1
P Battery pack 1
Sensor control box
HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.
R 1
SSoap assembly 1
Soap pump
T 1
USoap bottle 1
Soap dispenser
mounting nut
Q"AA" Battery 4
P
A
L
M
B
C
D
E
F
J
I
H
G
K
R
S
T
U
Sensor Control Box
Soap Pump Assembly
Q
N
O
4
Installation
1 Installing the faucet assembly
Install the faucet body (A)-including supply
hoses and sensor cable (1)-through the hole
in the sink.
CAUTION: Always turn off the water supply before
removing an existing faucet or replacing any part of a
faucet. Open the faucet handle to relieve water pressure
and ensure that the water is completely shut off.
NOTE: This step is for no escutcheon installation (optional).
If the escutcheon will be used, install the faucet assembly
as described in step 2.
2Installing the escutcheon
Screw the bolts (H) into the escutcheon (G) and
ensure that the gasket (I) is pressed onto the
escutcheon (G) before the escutcheon (G) is
installed over the three holes in the sink.
Secure the escutcheon (G) to the sink using the
mounting nuts (J) provided. Hand tighten only.
NOTE: If the sink is uneven, use silicone under the
gasket (I).
NOTE: This step is for escutcheon installation (optional).
If the escutcheon will not be used, install the faucet
assembly as described in step 1.
Shut off the water supply. Remove the old
faucet.
Clean the mounting surface.
Proceed to step 4.
A
1
G
H
I
J
5
Installation (continued)
3 Installing the faucet assembly
Install the faucet body (A)-including supply
hoses and sensor cable (1)-through the hole
in the escutcheon (G).
NOTE: This step is for escutcheon installation (optional).
If the escutcheon will not be used, install the faucet
assembly as described in step 1.
4 Securing the faucet assembly
Install the rubber washer (B) and metal washer (C)
onto the threaded shank.
HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.
Thread the mounting nut (D) onto the shank using
the wrench (F) provided to tighten rmly.
G
A
1D
C
B
D
1
3
F
D
F
4
2
6
Installation (continued)
5 Installing the protective cap
Screw the protective cap (E) onto the threaded
mounting shank (1).
6
Installing the pulldown hose
Before installing the hose (K), ensure that the
protective cap (1) is on the end of the hose (K).
Insert the small end of the pulldown hose (K) into
the spout (2) and feed through faucet body (A)
and the threaded mounting shank (3) in the
direction shown below.
7 Attaching the quick connector
to the hose
Before installing the quick connector, remove
and discard the protective cap (1) from the
pulldown hose (K).
Attach the quick connector (N) by screwing it
onto the threaded end of the hose (K) in a
clockwise motion. Hand tighten only.
K
1
K
1
2
N
1
E
1
E
1
2
1
A
2
3
K
7
Installation (continued)
8
HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.
Attaching the quick connector
to the receiving block
NOTE: The side of the control box (O) with "in" and "out"
showing must face the front of the cabinet (away from the
back of the cabinet).
Connect the hose with the yellow tag to the hose
on the control box (O) with a matching yellow tag.
Push rmly together until they snap into place.
NOTE: If you want to use the faucet without the sensor
feature or without power, you can attach the quick
connector (1) to the receiving block (2). This bypasses the
sensor feature and enables the faucet to work by operating
the handle.
Connect the hose with the green tag to the hose
on the control box with a matching green tag.
Push rmly together until they snap into place.
9Installing the sensor cable
Install the data cable (1) to the control box connection (2). Ensure the arrows on the data cable (3) and the
control box connection (4) are aligned to one another to ensure proper installation. Ensure they are tightly
connected by rmly pushing together.
Secure the connection by hand tightening the nut (5) in a clockwise direction onto the threaded sensor cable.
CAUTION: If the connections are not made properly, the
sensor feature will not work.
O
2
1
Yellow
Yellow
Green
Green
5
1
1
2
3
4
2
8
Installation (continued)
10Installing the batteries
Squeeze the side indicated by the arrows (5) below on the battery pack (P) and then pull down to remove
the cover (1). See g 1.
Install the four AA batteries (Q) included by matching the positive (+) and Negative (-) ends on the battery (Q)
to the (+) and (-) markings in the battery pack (P). The negative ends of the battery (Q) should always
connect to the spring end of the battery slots in the battery pack (P). See g 2.
Reinstall the battery pack cover (1) by pushing up and snapping into place. See gure 3.
NOTE: When the sensor ashes 10 times continuously
and slowly, the batteries have lost their charge. Replace
the batteries (Q).
NOTE: This step is for batteries installation (optional). If the
batteries will not be used, install as described in step 12.
Figure 1 Figure 2 Figure 3
P
(+)
(-)
P
P
1
5
5(-)
1
(+)
(-)
Q
P
Q
9
Installation (continued)
11Installation using the battery
pack
There are 2 options to secure the battery pack (P) under the counter: Tape Installation or Screw Installation.
Screw Installation: Drill holes in the wall using a 6mm (15/64”) diamater drill bit. Install the battery pack
seat (1) using the molly anchors (3) and screws (4) provided.
HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.
Tape Installation: Attach one side of the double sided tape (2) to the battery pack seat (1). Firmly attach the
battery pack seat (1) to the cabinet wall. Place the battery pack (P) into the battery pack seat (1).
NOTE: This step is for battery installation (optional). If the
battery will not be used, install as described in step 12. Before
installation, select the location for the battery pack (P) and
verify that the battery pack wire will reach the connection on
the bottom of the control box (O).
Insert the battery pack cable (5) into the control box connection (6). Ensure the arrows on the data cable (7)
and the control box connection (8) are aligned to one another to ensure proper installation.
Screw Installation
1
(15/16") dia.
P
1
43
6mm
2
1
6
5
O
8
7
Tape Installation
2
1
1
P
1
1
2
3
OR
CAUTION: If the connections are not made properly, the
sensor feature will not work.
Installation (continued)
10
12Installation using the AC
adapter (not included)
NOTE: This step is for installation without batteries using
an AC adapter (not included). If using the batteries, install
as instructed in step 10 and skip to step 13. The AC adapter
is not included with the product, but can be purchased from
Homedepot.com.
Install the AC adapter (5) into the power outlet.
Insert the AC adapter cable (1) into the control box port (2). Ensure the arrows on the data cable (3) and the
control box connection (4) are aligned to one another to ensure proper installation.
5
2
1
4
3
CAUTION: If the connections are not made properly, the
sensor feature will not work.
11
Installation (continued)
HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.
Push
up
Screw
T
Sink Sink
Fig 1
14 Installing the soap dispenser
Insert the soap assembly (S) through the
selected hole in the sink. Secure the soap
assembly to the sink with the soap
dispenser mounting nut (T) provided. Push
up the soap dispenser mounting nut (T) to
sink and hand-turn to tighten, as shown in
the Fig 1.
From under the sink, screw the soap bottle (U)
onto the soap assembly (S) shank. Insert the
soap pump (R) down into the soap assembly (S).
13Installing the weight
Install the weight clip (L) at the point of the hose (K) marking “weight here”.
Insert the weight (M) onto the clip (L) by sliding it down onto the clip (L).
Weight
here
M
L
K
Weights
here
R
S
T
U
1
4
2
3
12
1Flushing and checking for leaks
Pull the hose assembly out of the spout and
remove the spray head by unscrewing it from
the hose in a counterclockwise direction. Be
sure to hold the end of the hose down into the
sink and turn the faucet to the warm position
where it mixes hot and cold water.
Flush the water lines for one minute. This ushes
away any debris that could cause damage to
internal parts. Check for leaks.
Re-tighten any connections if necessary, but do
not overtighten. Reinstall the spray head by hand
tightening it back onto the spray hose in a
clockwise direction.
Operation
IMPORTANT: After installation is completed, turn on the
hot and cold water supplies. Check for leaks. Do not lose
the gasket (1) in the hose.
15 Making the water supply
connections
Thread the nut (1) on the supply line onto the
outlet of the water supply valve (2) and tighten
with a wrench. Do not overtighten.
Installation (continued)
NOTE: The hot side inlet tube is indicated by a label. Avoid
twisting wires together or placing the wires close to each
other and damaging.
1
2
1
HC
13
Operation (continued)
HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.
Care and Cleaning
To clean, wipe down with a damp cloth and towel dry
Do not use abrasive cleaners, steel wool, or harsh chemicals when cleaning this faucet, or the warranty will
be voided.
3Removing the quick connector
If it is necessary to remove the quick connector
(1), squeeze the tabs (2) on the quick connector
and then pull down to disconnect.
2Operating the sensor
Turn the handle (1) to the full on position, activating
the sensor (2) and turning the water on.
To turn the water off, move your hand within the
sensor range (8in. MAX) as shown.
NOTE: The sensor is active only when the handle is in the
ON position.
NOTE: As a water saving feature, the water will turn off
automatically after 3 minutes of continuous ow.
min.
45
30
0
15
3
8 in. MAX
2
1
To turn the water on, move your hand within the
sensor range again (8in. MAX range) as shown.
Leave the handle (1) in the ON position, and you
can start and stop the ow of water simply with
a wave of your hand.
Squeeze
2
Pull
down
11
14
Troubleshooting
1Water will not shut off when
turning the handle to the OFF
position
When you turn the handle to the full on position,
the water will turn on
But when you turn the handle to the full off
position, the water does not turn off.
This indicates that the cartridge is damaged.
Turn off the water supply, remove the handle
and replace the cartridge (1).
1
2The light on the sensor is
flashing continuously
If the handle is closed, turn the handle to the
on position and move your hand in the sensor
area. If the sensor ashes 10 times continuously
and slowly, then replace the 4 "AA" batteries.
1
Replace the batteries
Flash 10 times
continuously
and slowly
15
Troubleshooting (continued)
4There is a low flow of water or
LED indicator in the spray head
is not functioning
This could indicate that the washer in the "in" end of
the control box is dirty or damaged. Remove the
hose and unscrew the connector. Take out the
washer from the control box. Clear the washer
or replace the washer. Reassemble the connector
and hose.
HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.
3The sensor is not activating
the water flow
When you turn the handle to the full on position,
the water will turn on.
However, when you move your hand in front
of the sensor, the water does not turn off as
it should.
This indicates that the control box is damaged.
Call Glacier Bay customer service to request
a replacement control box. Replace the old
control box with the new control box.
1
Hose
Connector
Control
box
Washer
16
Service Parts
Part Description Part Number
1 RP38223*
2 Wearable ring RP70380
3 O-ring RP60071
5Bonnet nut RP70394
6 Cap RP80028*
7 Handle RP13368*
9 Index & O-ring RP80440*
11 Metal washer RP64088
Spray head and Hose
15 O-ring RP60002
23 Mounting nut RP56036
24 Sensor control box RP70451
25 Battery pack RP70452
26 Pump kit RP46022
Part Description Part Number
12 Nut RP56098
13 Protective cap RP70448
16 Quick connect
assembly RP70482
17 O-ring RP60089
18 Weight clip RP64204
19 Weight RP70441
20 Escutcheon RP80441*
21 Bolt RP50071
22 RP80442
Gasket
4 Cartridge RP20005
8 Screw RP50015
10 Rubber washer RP64087
14 Block RP70421
27 Flange kit RP46066*
28 Soap bottle RP46060
29 Soap dispenser kit RP46065*
*Specify Finish
Many replacement cartridges, aerators, and drain
assemblies can be purchased at your local The
Home Depot store or online at HOMEDEPOT.COM
Faucet ID tags can
be found on the
hot water inlet 25
2
13
4567
89
20
21
22
23
10
11
12
13
14
15
17
18
19
26
27
28
29
16 24
Questions, problems, missing parts?
Before returning to the store, call Glacier Bay Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday
9 a.m. - 6 p.m., EST, Saturday
1-855-HD-GLACIER (1-855-434-5224)
HOMEDEPOT.COM
Retain this manual for future use.
GRACIAS
GUÍA DE USO Y MANTENIMIENTO
¿Problemas, preguntas o piezas faltantes?
Antes de regresar a la tienda, llama al servicio al cliente de
Glacier Bay de lunes a viernes entre 8 a.m. y 7 p.m. y los
sábados entre 9 a.m. y 6 p.m.(hora estándar del Este)
1-855-HD-GLACIER (1-855-434-5224)
HOMEDEPOT.COM
Modelo núm.
67536-1001
67536-1008D2
67536-1027H2
GRIFO RETRÁCTIL PARA COCINA
Agradecemos la con anza que has depositado en Glacier Bay al comprar este grifo para cocina. Nos esforzamos
por crear continuamente productos de calidad diseñados para mejorar tu hogar. Visítanos en Internet para ver
nuestra línea completa de productos disponibles para las necesidades de mejoras de tu hogar. ¡Gracias por
elegir a Glacier Bay!
SKU núm.
682-892
665-466
682-894
Llave
ajustable
Gafas de
seguridad
Destornillador
Phillips
SILICONE
Sellador de
silicona
Taladro
eléctrico de
6 mm de
diámetro
Pinzas
ajustables
19
Información importante
Cumple con todos los códigos locales de construcción y de plomería.
Cubre el drenaje del lavabo para evitar que se pierda alguna pieza.
Consulta la sección de mantenimiento y limpieza incluida en esta guía.
HERRAMIENTAS Y HERRAJES NECESARIOS
Tabla de contenido
Información importante .........................19
Garantía...................................................19
Pre-instalación .......................................19
.............19
Herramientas y herrajes necesarios ....19
Contenido del paquete .........................20
Instalación ..............................................21
Funcionamiento ......................................29
Cuidado y limpieza ................................30
Piezas de repuesto ................................33
Planicación de la instalación Solución de problemas ...........................31
Garantía
GARANTÍA LIMITADA DE POR VIDA
Los productos de Glacier Bay están fabricados con normas y mano de obra de calidad superior y están respaldados
por nuestra garantía de por vida limitada. Glacier Bay garantiza al comprador consumidor original que sus productos
no presentan defectos materiales o de fabricación. El mecanismo del sensor y las luces LED están excluidos de la
garantía limitada de por vida y están cubiertos por una garantía de 3 años desde el momento de la compra.
Simplemente, devuelva el producto o pieza a cualquiera de las tiendas minoristas de The Home Depot o llame al
1-855-HD-GLACIER (1-855-434-5224) para recibir el artículo de reemplazo. El comprobante de compra (recibo de venta
original) del comprador consumidor original debe estar disponible para todos los reclamos de garantía de Glacier Bay.
Esta garantía excluye daños y fallos incidentales/consecuenciales debido al mal uso, abuso o desgaste normal por
el uso. Esta garantía excluye todos los usos industriales, comerciales y de negocios, a cuyos compradores se les
extiende en la presente una garantía limitada de cinco años a partir de la fecha de compra, con todos los otros
artículos de esta garantía que aplican excepto la duración de la garantía.
Algunos estados y provincias no permiten la exclusión o la limitación de los daños incidentales o consecuentes,
por lo tanto, las limitaciones y exclusiones anteriores podrían no aplicarse a su caso. Esta garantía le otorga derechos
tienda o llame al 1-855-HD-GLACIER para obtener más detalles.
Pre-instalación
PLANIFICACIÓN DE LA INSTALACIÓN
Antes de comenzar la instalación de este producto, asegúrate de que no falta ninguna pieza. Compara las piezas
con la lista de Contenido del paquete. Si falta alguna pieza o está dañada, no intentes instalar el producto.
Comunícate con el servicio al cliente para piezas de repuesto.
Pieza Descripción Cantidad
A 1Cuerpo del grifo
B 1
C Arandela metálica 1
Arandela de goma
D 1
E Tapa protectora 1
Tuerca
H 2
IJunta 1
Perno
FLlave 1
G Placa protectora 1
LSujetador con peso 1
JTuerca de montaje 2
K 1
Manguera y
cabezal rociador
Pieza Descripción Cantidad
MPeso 1
NEnsamblaje del
conector rápido 1
O 1
P Paquete de baterías 1
Caja de control
del sensor
R 1
SEnsamblaje para
jabón 1
Bomba para jabón
T 1
UBotella de jabón 1
Tuerca de montaje
para el dispensador
de jabón
Caja de control
del sensor Ensamblaje de la
bomba para jabón
QBatería “AA” 4
20
Pre-instalación (continuación)
CONTENIDO DEL PAQUETE
HOMEDEPOT.COM
Para obtener asistencia, llama al 1-855-HD-GLACIER.
P
A
L
M
B
C
D
E
F
J
I
H
G
K
R
S
T
U
Q
N
O
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51

Glacier Bay 67536-1001 Guide d'installation

Catégorie
Articles sanitaires
Taper
Guide d'installation