Generac 6500E 0068651 Manuel utilisateur

Owner’s Manual

HomeLink™ 6500 Series Portable Generator

*

NOT INTENDED FOR USE IN CRITICAL

LIFE SUPPORT APPLICATIONS.

*

DEADLY EXHAUST FUMES! USE

OUTSIDE, ONLY, FAR AWAY FROM

WINDOWS, DOORS AND VENTS!

*

SAVE THIS MANUAL. Provide this

manual to any operator of the generator.

Reference all appropriate documentation.

This manual should remain with the unit.

ii

(000004)

WARNING

California Proposition 65. Engine exhaust and some of

its constituents are known to the state of California to

cause cancer, birth defects, and other reproductive

harm.

(000005)

WARNING

California Proposition 65. This product contains or

emits chemicals known to the state of California to

cause cancer, birth defects, and other reproductive

harm.

iii

Table of Contents

Unit Information ..........................................................iii

Section 1 - Safety ........................................................1

1.1 Read This Manual Thoroughly................................1

1.2 Safety Rules............................................................1

Section 2 - General Information.................................5

2.1 Unpacking ...............................................................5

2.2 Assembly ................................................................5

2.3 Emissions Information.............................................6

2.4 Product Specifications ............................................6

2.5 Know The Generator............................................... 7

2.6 Before Starting the Generator.................................9

Section 3 - Operation................................................11

3.1 How To Use The Generator..................................11

3.2 Generator Loads ...................................................12

3.3 Wattage Reference Guide ....................................12

3.4 Starting The Generator (Electric Start) .................12

3.5 Starting The Generator (Manual/Recoil)

Starting ..................................................................13

3.6 Stopping The Generator .......................................13

3.7 Low Oil Level Shutdown System ..........................13

Section 4 - Maintenance ...........................................15

4.1 General Recommendations ..................................15

4.2 Generator Cleaning...............................................15

4.3 Service Intervals ...................................................15

4.4 Generator Storage ................................................20

Section 5 - Troubleshooting ....................................21

5.1 Troubleshooting Guide..........................................21

5.2 Replacement Service Parts ..................................22

Unit Information

Record the information found on your unit data label on

this page. The location of the unit data label is shown

below.

When contacting an Authorized Service Dealer about

parts and service, always supply the complete model

number and serial number of the unit.

Operation and Maintenance: Proper maintenance and

care of the generator ensures a minimum number of

problems and keep operating expenses at a minimum. It

is the operator’s responsibility to perform all safety

checks, make sure all maintenance for safe operation is

performed promptly, and to have the equipment checked

periodically by an Authorized Service Dealer. Normal

maintenance, service and replacement of parts are the

responsibility of the owner/operator and are not consid-

ered defects in materials or workmanship within the

terms of the warranty. Individual operating habits and

usage may contribute to the need for additional mainte-

nance or service.

When the generator requires servicing or repairs, contact

an Authorized Generac Service Dealer for assistance.

Authorized service technicians are factory-trained and

can handle all servicing needs.

MODEL NO:

SERIAL NO:

000198

iv

This page intentionally left blank.

HomeLink 6500 Series Portable Generator 1

Thank you for purchasing this model by Generac Power

Systems, Inc. This model is a compact, high perfor-

mance, air-cooled, engine driven generator designed to

supply electrical power to operate electrical loads where

no utility power is available or in place of utility due to a

power outage.

1.1 — READ THIS MANUAL THOROUGHLY

If any portion of this manual is not understood, contact

the nearest Authorized Dealer for starting, operating and

servicing procedures.

The operator is responsible for proper and safe use of

the equipment. We strongly recommend that the operator

read this manual and thoroughly understand all instruc-

tions before using the equipment. We also strongly rec-

ommend instructing other users to properly start and

operate the unit. This prepares them if they need to oper-

ate the equipment in an emergency.

The generator can operate safely, efficiently and reliably

only if it is properly located, operated and maintained.

Before operating or servicing the generator:

• Become familiar with and strictly adhere to all local,

state and national codes and regulations.

• Study all safety warnings in this manual and on the

product carefully.

Become familiar with this manual and the unit before use.

The manufacturer cannot anticipate every possible cir-

cumstance that might involve a hazard. The warnings in

this manual, and on tags and decals affixed to the unit

are, therefore, not all inclusive. If using a procedure, work

method or operating technique that the manufacturer

does not specifically recommend, ensure that it is safe for

others. Also make sure the procedure, work method or

operating technique utilized does not render the genera-

tor unsafe.

THE INFORMATION CONTAINED HEREIN WAS

BASED ON MACHINES IN PRODUCTION AT THE

TIME OF PUBLICATION. GENERAC RESERVES THE

RIGHT TO MODIFY THIS MANUAL AT ANY TIME.

Save these instructions for future reference. If you

loan this device to someone, ALWAYS loan these

instructions to the individual as well.

1.2 — SAFETY RULES

Throughout this publication, and on tags and decals

affixed to the generator, DANGER, WARNING, CAUTION

and NOTE blocks are used to alert personnel to special

instructions about a particular operation that may be haz-

ardous if performed incorrectly or carelessly. Observe

them carefully. Their definitions are as follows:

NOTE: Notes contain additional information import-

ant to a procedure and will be found within the regu-

lar text body of this manual.

These safety warnings cannot eliminate the hazards that

they indicate. Common sense and strict compliance with

the special instructions while performing the action or

service are essential to preventing accidents.

(000001)

DANGER

Indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

(000003)

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

(000002)

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Section 1 Safety

2 HomeLink 6500 Series Portable Generator

Four commonly used safety symbols accompany the

DANGER, WARNING and CAUTION blocks. The type of

information each indicates is as follows:

This symbol points out important safety infor-

mation that, if not followed, could endanger

personal safety and/or property of others.

This symbol points out potential explosion

hazard.

This symbol points out potential fire hazard.

This symbol points out potential electrical

shock hazard.

1.2.1 — General Hazards

• NEVER operate in an enclosed area, in a vehicle, or

indoors EVEN IF doors and windows are open.

• For safety reasons, the manufacturer recommends

that the maintenance of this equipment is carried out

by an Authorized Dealer. Inspect the generator regu-

larly, and contact the nearest Authorized Dealer for

parts needing repair or replacement.

• Operate generator only on level surfaces and where it

will not be exposed to excessive moisture, dirt, dust or

corrosive vapors.

• Keep hands, feet, clothing, etc., away from drive belts,

fans, and other moving parts. Never remove any fan

guard or shield while the unit is operating.

• Certain parts of the generator get extremely hot during

operation. Keep clear of the generator until it has

cooled to avoid severe burns.

• Do NOT operate generator in the rain.

• Do not alter the construction of the generator or

change controls which might create an unsafe operat-

ing condition.

• Never start or stop the unit with electrical loads con-

nected to receptacles AND with connected devices

turned ON. Start the engine and let it stabilize before

connecting electrical loads. Disconnect all electrical

loads before shutting down the generator.

• Do not insert objects through unit’s cooling slots.

• When working on this equipment, remain alert at all

times. Never work on the equipment when physically

or mentally fatigued.

• Never use the generator or any of its parts as a step.

Stepping on the unit can stress and break parts, and

may result in dangerous operating conditions from

leaking exhaust gases, fuel leakage, oil leakage, etc.

1.2.2 — Exhaust & Location Hazards

Never operate in an enclosed area or indoors!

NEVER use in the home, in a vehicle, or in partly

enclosed areas such as garages, EVEN IF doors and

windows are open! ONLY use outdoors and far from

open windows, doors, vents, and in an area that will

not accumulate deadly exhaust.

• The engine exhaust fumes contain carbon monoxide,

which you cannot see or smell. This poisonous gas, if

breathed in sufficient concentrations, can cause

unconsciousness or even death.

• Adequate, unobstructed flow of cooling and ventilating

air is critical to correct generator operation. Do not

alter the installation or permit even partial blockage of

ventilation provisions, as this can seriously affect safe

operation of the generator. The generator MUST be

operated outdoors.

• This exhaust system must be properly maintained. Do

nothing that might render the exhaust system unsafe

or in noncompliance with any local codes and/or stan-

dards.

• Always use a battery operated carbon monoxide

alarm indoors, installed according to the manufactur-

ers instructions.

• If you start to feel sick, dizzy, or weak after the genera-

tor has been running, move to fresh air IMMEDI-

ATELY. See a doctor, as you could have carbon

monoxide poisoning.

*

$

!

+

HomeLink 6500 Series Portable Generator 3

1.2.3 — Electrical Hazards

• The generator produces dangerously high voltage

when in operation. Avoid contact with bare wires, ter-

minals, connections, etc., while the unit is running,

even on equipment connected to the generator.

Ensure all appropriate covers, guards and barriers are

in place before operating the generator.

• Never handle any kind of electrical cord or device

while standing in water, while barefoot or while hands

or feet are wet. DANGEROUS ELECTRICAL SHOCK

MAY RESULT.

• The National Electric Code (NEC) requires the frame

and external electrically conductive parts of the gener-

ator be properly connected to an approved earth

ground. Local electrical codes may also require proper

grounding of the generator. Consult with a local elec-

trician for grounding requirements in the area.

• Use a ground fault circuit interrupter in any damp or

highly conductive area (such as metal decking or steel

work).

• Do not use worn, bare, frayed or otherwise damaged

electrical cord sets with the generator.

• Before performing any maintenance on the generator,

disconnect the engine starting battery (if equipped) to

prevent accidental start up. Disconnect the cable from

the battery post indicated by a NEGATIVE, NEG or (–)

first. Reconnect that cable last.

• In case of accident caused by electric shock, immedi-

ately shut down the source of electrical power. If this

is not possible, attempt to free the victim from the live

conductor. AVOID DIRECT CONTACT WITH THE

VICTIM. Use a non-conducting implement, such as a

rope or board, to free the victim from the live conduc-

tor. If the victim is unconscious, apply first aid and get

immediate medical help.

1.2.4 — Fire Hazards

• Gasoline is highly FLAMMABLE and its vapors are

EXPLOSIVE. Never permit smoking, open flames,

sparks or heat in the vicinity while handling gasoline.

• Never add fuel while unit is running or hot. Allow

engine to cool completely before adding fuel.

• Never fill fuel tank indoors. Comply with all laws

regulating storage and handling of gasoline.

• Do not overfill the fuel tank. Always allow room for

fuel expansion. If tank is over-filled, fuel can overflow

onto a hot engine and cause FIRE or an EXPLOSION.

Never store generator with fuel in tank where gasoline

vapors might reach an open flame, spark or pilot light

(as on a furnace, water heater or clothes dryer). FIRE

or EXPLOSION may result. Allow unit to cool entirely

before storage.

• Wipe up any fuel or oil spills immediately. Ensure that

no combustible materials are left on or near the gener-

ator. Keep the area surrounding the generator clean

and free from debris and keep a clearance of five (5)

feet on all side to allow for proper ventilation of the

generator.

• Do not insert objects through unit’s cooling slots.

• Never operate the generator if connected electrical

devices overheat, if electrical output is lost, if engine

or generator sparks or if flames or smoke are

observed while unit is running.

• Keep a fire extinguisher near the generator at all

times.

NOTE: California CARB models only are equipped

with a spark arrestor muffler. The spark arrestor must

be maintained in effective working order by the

owner/ operator. In the state of California, a spark

arrestor is required by law (Section 4442 of the Pub-

lic Resources Code). Other states may have similar

laws. Federal laws apply on federal lands.

1.2.5 — Standards Index

1. National Fire Protection Association (NFPA) 70: The

NATIONAL ELECTRIC CODE (NEC) available from

www.nfpa.org

2. National Fire Protection Association (NFPA) 5000:

BUILDING CONSTRUCTION AND SAFETY CODE

available from www.nfpa.org

3. International Building Code available from

www.iccsafe.org

4. Agricultural Wiring Handbook available from

www.rerc.org , Rural Electricity Resource Council

P.O. Box 309 Wilmington, OH 45177-0309

5. ASAE EP-364.2 Installation and Maintenance of

Farm Standby Electric Power available from

www.asabe.org, American Society of Agricultural &

Biological Engineers 2950 Niles Road, St. Joseph,

MI 49085

This list is not all inclusive. Check with the Authority Hav-

ing Local Jurisdiction (AHJ) for any local codes or stan-

dards which may be applicable to your jurisdiction.

4 HomeLink 6500 Series Portable Generator

This page intentionally left blank.

HomeLink 6500 Series Portable Generator 5

2.1 — UNPACKING

• Remove all packaging material.

• Remove separate items.

• Remove the generator from carton.

2.1.1 — Documents and Accessories

(not shown)

Check all contents. If any parts are missing or damaged,

call 1-888-436-3722.

• Product Registration Card

• Warranty and Emission Sheets

• 1 - Owner’s Manual

• 1 - Quart Oil - SAE 30W

• 1 - Battery Charger

• 1 - Oil Funnel

• 1 - Manual Transfer Switch

2.1.2 — Loose Components

• 1 - Hardware Bag (containing the following):

— 2 - Cotter Pins

(A)

— 2 - Washers (B)

— 2 - Never-Flat Wheels (C)

— 2 - Axle Pins (D)

— 2 - Frame Foot Assembly (E)

— 4 - Hex Flanged Nuts (M8) (F)

— 4 - Hex Bolts (M8) (G)

— 1 - Handle Assembly (L) (not in hardware bag)

— 2 - Hex Bolt (M8 X 55 mm) (M)

— 4 - Washer, Nylon (N)

— 2 - Nut, Hex Lock (P)

2.2 — ASSEMBLY

The generator requires some assembly prior to usage. If

problems arise when assembling the generator, call 1-

888-436-3722.

2.2.1 — Required Tools

— 1 - Ratchet wrench

— 1 - 13 mm socket

— 2 - 8 mm wrenches

— 1 - 13 mm wrench

— 1 - Needle nosed pliers

2.2.2 — Installing Wheels

NOTE: The wheels are not intended for over-the-road

use.

1. Install the Wheels as follows (Figure 2-1):

— Slide the Axle Pin through the Wheel, Wheel

Bracket on the frame and a 5/8" Flat Washer.

— Insert the Cotter Pin through the Axle Pin. Use the

needle nosed pliers to bend open to lock in place.

Figure 2-1. Wheel Assembly

2.2.3 — Installing Frame Feet

2. Install the Frame Foot Assemblies as shown (Figure

2-2).

— Slide the M8 Hex Bolts through the holes in the

Frame Rail.

— Slide the Frame Foot onto the Hex Head Bolts.

Then install the Locking Flange Nuts. Tighten

securely using a ratchet, 13 mm socket and 13

mm wrench.

Figure 2-2. Frame Foot Assemblies

000199

A B

C

D

000243

E

F

G

Section 2 General Information

6 HomeLink 6500 Series Portable Generator

2.2.4 — Installing Handle

1. Place the handle brackets between the frame tabs as

shown. Place a flat washer on the inside of each

frame tab (Figure 2-3).

2. Slide bolts through the handle brackets, washers and

tabs.

3. Place a nut on each bolt and tighten securely using a

ratchet, 13 mm socket and 13 mm wrench.

Figure 2-3. Handle

2.2.5 — Battery Cables

NOTE: The battery shipped with the generator has

been fully charged. The positive and negative cables

are NOT connected and must be attached prior to

operation.

The NEGATIVE (black) (-) battery cable should:

1. Always be DISCONNECTED FIRST.

2. Always be CONNECTED LAST.

Use two 8 mm wrenches to tighten battery hardware.

Figure 2-4. Battery Connections

NOTE: A battery may lose some of its charge when

not in use for prolonged periods of time. If the bat-

tery is unable to crank the engine, plug in the 12V

charger included in the accessory box (see the

Charging a Battery - Section 4: Maintenance). RUN-

NING THE GENERATOR DOES NOT CHARGE THE

BATTERY.

2.3 — EMISSIONS INFORMATION

The Environmental Protection Agency (and California Air

Resource Board for generators certified to CA standards)

requires that this generator comply with exhaust and

evaporative emission standards. Locate the emissions

compliance decal on the engine to determine what stan-

dards the generator meets, and to determine which war-

ranty applies. This generator is certified to operate on

gasoline. The emission control system includes the fol-

lowing components (if equipped):

• Air Induction System

— Intake Pipe / Manifold

— Air Cleaner

•Fuel System

— Carburetor/Mixer Assembly

— Fuel Regulator

• Ignition System

— Spark Plug

— Ignition Module

• Exhaust System

— Exhaust Manifold

— Muffler

— Pulsed Air Valve

— Catalyst

2.4 — PRODUCT SPECIFICATIONS

2.4.1 — Generator Specifications

Rated Power.......................................................... 6500 W

Surge Power..........................................................8125 W

Rated AC Voltage................................................. 120/240

Rated AC Load

Current @ 240V .......................................... 27.1 Amps**

Current @ 120V .......................................... 54.2 Amps**

Rated Frequency................................ 60 Hz @3600 RPM

Phase ...........................................................Single Phase

Total Harmonic Distortion ...........................................<5%

Operating Temperature Range...... 0° F (-17° C) to 110° F

Dry Weight................................................. 202 lbs (92 kg)

* Operating temperature range: 0° F (-18° C) to 104° F (40° C). When

operated above 77° F (25° C) there may be a decrease in power.

** Maximum wattage and current are subject to, and limited by, such

factors as fuel Btu content, ambient temperature, altitude, engine

condition, etc.. Maximum power decreases about 3.5% for each

1,000 feet above sea level; and will also decrease about 1% for each

10° F (-12.2° C) above 60° F (16° C) ambient temperature.

N

P

M

L

+

_

POSITIVENEGATIVE

HomeLink 6500 Series Portable Generator 7

2.4.2 — Engine Specifications

Displacement ........................................................389 cc

Spark Plug Type................................... Champion N9YC

Spark Plug Gap.......0.028-0.031 inch or (0.70-0.80 mm)

Fuel Capacity ................................7.5 gallons/ 28.4 liters

Oil Type................................................see Section 2.6.1

Oil Capacity..................................1.06 Quarts (1.0 liters)

Run Time at 50% Load ..................................... 12 Hours

2.5 — KNOW THE GENERATOR

Compare the generator to Figures 2-5 through 2-7 to

become familiarized with the locations of various controls

and adjustments.

Read the Owner’s Manual and Safety Rules before

operating this generator.

1. 120/240 Volt AC, 30 Amp, Locking Receptacle –

Supplies electrical power for the operation of 120

and/or 240 Volt AC, 30 Amp, single-phase, 60 Hz

electrical lighting, appliance, tool and motor loads.

2. Hour Meter - Tracks hours of operation to perform

required maintenance.

3. Circuit Breakers (AC) – A 2-pole circuit breaker pro-

tects the rated output of the 30 Amp Twistlock outlet.

Each duplex receptacle is provided with a push-to-

reset circuit breaker to protect against electrical over-

load.

4. 120 Volt AC, 20 Amp GFCI Duplex Outlets – Sup-

plies electrical power for the operation of 120 Volt

AC, 20 Amp, single-phase, 60 Hz, electrical lighting,

appliance, tool and motor loads. It also provides pro-

tection with an integral Ground Fault Circuit Inter-

rupter, complete with a press to “Test” and “Reset”

button.

5. Off/Run/Start Switch – Controls the operation of the

generator.

6. Battery Charger Input – Permits recharging of the

battery. A 12 volt charger is included. A 1.50 Amp in-

line fuse is located behind the control panel to protect

the battery when charging.

Figure 2-5. Control Panel

7. Grounding Location - Ground the generator to an

approved earth ground here. See “Grounding the

Generator” for details.

8. Muffler – Quiets the engine.

9. Fuel Cap - Remove to fill fuel tank.

10. Recovery Hose - vapor tube between roll over valve

and the engine.

11. Choke Lever - Used when starting a cold engine.

12. Air Filter - Filters into air as it is drawn into the

engine.

13. Recoil Starter – Used to start engine manually.

14. Fuel Valve - Turns fuel supply on and off.

15. Handle – Used to transport generator.

16. Fuel Gauge - Shows fuel level in tank.

17. Roll Over Valve - Passes fuel vapors to the engine.

18. Fuel Tank - holds fuel supply.

19. Oil Drain - Drain plug for removing used oil from the

crankcase.

20. Oil Fill/Dipstick - Check oil level and add oil here.

21. Battery - Provides power for electric starter.

000244

4

6

5

2

1 3

8 HomeLink 6500 Series Portable Generator

Figure 2-6. Generator Controls

Figure 2-7. Oil Drain/Fill

2.5.1 — Connection Plugs

2.5.1.1 — 120 VAC, 20 Amp, GFCI Duplex

Receptacle

This is a 120 Volt outlet protected against overload by a

20 Amp push-to-reset circuit breaker (Figure 2-8). Use

each socket to power 120 Volt AC, single phase, 60 Hz

electrical loads requiring up to a combined 2400 watts

(2.4 kW) or 20 Amps of current. Use only high quality,

well-insulated, 3-wire grounded cord sets rated for 125

Volts at 20 Amps (or greater).

Keep extension cords as short as possible, preferably

less than 15 feet long, to prevent voltage drop and possi-

ble overheating of wires.

Figure 2-8. 120 Volt AC, 20 Amp, GFCI

Duplex Receptacle

000202

21

18

17

13

16

12

7

8

9

10

11

14

15

19

20

DIPSTICK / FILL OPENING

OIL DRAIN PLUG

000203

HomeLink 6500 Series Portable Generator 9

2.5.1.2 — 120/240 VAC, 30 Amp Locking

Receptacle

Use a NEMA L14-30 Plug with this receptacle (rotate to

lock/unlock) (Figure 2-9). Connect the supplied 4-wire

grounded cord set to the plug and to the desired load.

The cord set should be rated for 250 Volts AC at 30 Amps

(or greater).

Use this receptacle to operate 120 Volt AC, 60 Hz, single

phase loads requiring up to 3600 watts (3.6 kW) of power

at 30 Amps or 240 Volt AC, 60 Hz, single phase loads

requiring up to 7,200 watts of power. The outlet is pro-

tected by a 30 Amp circuit breaker.

Figure 2-9. 120/240 VAC, 30 Amp Receptacle

2.5.2 — Hour Meter

The hour meter tracks hours of operation for scheduled

maintenance (Figure 2-10).

There will be a "CHG OIL" message every 100 hours.

The message will flash one hour before and one hour

after each 100 hour interval, providing a two hour window

to perform service.

This message will actually begin flashing at 99 hours and

disable itself at 101 hours again, providing a two hour

window to perform the service.

Every 200 hours the "SVC" icon on the lower left hand

corner of the display will flash. The message will flash

one hour before and one hour after each 200 hour inter-

val providing a two hour window to perform service.

Figure 2-10. Hour Meter

When the hour meter is in the Flash Alert mode, the

maintenance message will always alternate with elapsed

time in hours and tenths. The hours will flash four times,

then alternate with the maintenance message four times

until the meter resets itself.

• 100 hours - CHG OIL — Oil Change Interval (Every

100 hrs)

• 200 hours - SVC — Service Air Filter (Every 200 hrs)

NOTE: The hour glass graphic will flash on and off

when the engine is running. This signifies that the

meter is tracking hours of operation.

2.6 — BEFORE STARTING THE

G

ENERATOR

Prior to operating the generator:

• Engine oil will need to be added.

• Fill the fuel tank with unleaded fuel.

• Battery cables will need to be connected.

2.6.1 — Adding Engine Oil

The generator has been shipped WITHOUT oil. All oil

should meet minimum American Petroleum Institute

(API) Service Class SJ, SL or better. Use no special addi-

tives. Select the oil's viscosity grade according to the

expected operating temperature (also see chart).

• Above 40° F (4.4° C), use SAE 30

• Below 40° F (4.4° C) and down to 10° F (-12.2° C),

use SAE 10W-30

• All temperatures, use synthetic SAE 5W-30

000204

0000.0

000205

10 HomeLink 6500 Series Portable Generator

Any attempt to start the engine before it has been

properly serviced with the recommended oil may

result in an engine failure.

1. Place generator on a level surface (not to exceed 15°

in any direction).

2. Clean area around oil fill and remove oil fill cap/dip-

stick.

3. Wipe dipstick clean (Figure 2-11).

4. Slowly fill engine with oil through the oil fill opening.

Stop filling occasionally to check oil level. Fill until the

level is at the upper mark on the dipstick. Be careful

not to over fill.

Figure 2-11. Oil Fill/Dipstick

5. Install oil fill cap and finger tighten securely.

6. Check engine oil level before starting each time

thereafter.

2.6.2 — Adding Fuel

Never fill fuel tank indoors. Never fill fuel

tank when engine is running or hot. Avoid

spilling gasoline on a hot engine. Allow

engine to cool entirely before filling fuel tank.

DO NOT light a cigarette or smoke when

filling the fuel tank.

Do not overfill the fuel tank. Always leave

room for fuel expansion. If the fuel tank is

overfilled, fuel can overflow onto a hot

engine and cause FIRE or EXPLOSION. Wipe

up any spilled fuel immediately.

Use the following instructions for adding gasoline:

• Use regular UNLEADED gasoline with the generator

engine. Do not mix oil with gasoline.

• Do not use gasoline with more than 10% alcohol such

as E85 or ethanol.

• Clean area around fuel fill cap, remove cap.

• Slowly add unleaded gasoline to fuel tank. Be careful

not to overfill (Figure 2-12).

• Install fuel cap and wipe up any spilled gasoline.

Figure 2-12. Fuel Fill Level

IMPORTANT: It is important to prevent gum deposits

from forming in fuel system parts such as the carburetor,

fuel hose or tank during storage. Alcohol-blended fuels

(called gasohol, ethanol or methanol) can attract mois-

ture, which leads to separation and formation of acids

during storage. Acidic gas can damage the fuel system of

an engine while in storage. To avoid engine problems,

the fuel system should be emptied or treated with a com-

mercially available fuel stabilizer before storage of 30

days or longer. See the "Storage" section. Never use

engine or carburetor cleaner products in the fuel tank as

permanent damage may occur.

*

000116



$

000206

HomeLink 6500 Series Portable Generator 11

3.1 — HOW TO USE THE GENERATOR

See the "To Start the Engine" section for how to safely

start and stop the generator and how to connect and dis-

connect loads. If there are any problems operating the

generator, please call 1-888-77LOWES.

Never operate in an enclosed area or indoors!

NEVER use in the home, in a vehicle, or in

partly enclosed areas such as garages, EVEN

IF doors and windows are open! ONLY use out-

doors and far from open windows, doors,

vents, and in an area that will not accumulate

deadly exhaust.

The engine exhaust fumes contain carbon

monoxide, which you cannot see or smell. This

poisonous gas, if breathed in sufficient con-

centrations, can cause unconsciousness or

even death.

Adequate, unobstructed flow of cooling and

ventilating air is critical to correct generator

operation. Do not alter the installation or per-

mit even partial blockage of ventilation provi-

sions, as this can seriously affect safe

operation of the generator. The generator

MUST be operated outdoors.

This exhaust system must be properly main-

tained. Do nothing that might render the

exhaust system unsafe or in noncompliance

with any local codes and/or standards.

Always use a battery operated carbon monox-

ide alarm indoors, installed according to the

manufacturer's instructions.

3.1.1 — Grounding The Generator When

Used As A Portable

This generator has an equipment ground that connects

the generator frame components to the ground terminals

on the AC output receptacles (see NEC 250.34 (A) for

explanation). This allows the generator to be used as a

portable without grounding the frame of the generator as

specified in NEC 250.34.

Figure 3-1. Grounding the Generator

3.1.1.1 — Special Requirements

There may be Federal or State Occupational Safety and

Health Administration (OSHA) regulations, local codes,

or ordinances that apply to the intended use of the gener-

ator.

Please consult a qualified electrician, electrical inspector,

or the local agency having jurisdiction:

• In some areas, generators are required to be regis-

tered with local utility companies.

• If the generator is used at a construction site, there

may be additional regulations which must be

observed.

3.1.2 — Connecting The Generator To A

Building’s Electrical System

When connecting directly to a building’s electrical sys-

tem, it is recommended that a manual transfer switch is

used. Connections for a portable generator to a building’s

electrical system must be made by a qualified electrician

and in strict compliance with all national and local electri-

cal codes and laws.

*

000207

Section 3 Operation

12 HomeLink 6500 Series Portable Generator

3.2 — GENERATOR LOADS

Overloading a generator in excess of its rated wattage

capacity can result in damage to the generator and to

connected electrical devices. Observe the following to

prevent overloading the unit:

• Add up the total wattage of all electrical devices to be

connected at one time. This total should NOT be

greater than the generator's wattage capacity.

• The rated wattage of lights can be taken from light

bulbs. The rated wattage of tools, appliances and

motors can usually be found on a data label or decal

affixed to the device.

• If the appliance, tool or motor does not give wattage,

multiply volts times ampere rating to determine watts

(volts x amps = watts).

• Some electric motors, such as induction types, require

about three times more watts of power for starting

than for running. This surge of power lasts only a few

seconds when starting such motors. Make sure to

allow for high starting wattage when selecting electri-

cal devices to connect to the generator:

1. Figure the watts needed to start the largest motor.

2. Add to that figure the running watts of all other con-

nected loads.

The Wattage Reference Guide is provided to assist in

determining how many items the generator can operate

at one time.

NOTE: All figures are approximate. See data label on

appliance for wattage requirements.

3.3 — WATTAGE REFERENCE GUIDE

Device. . . . . . . . . . . . . . . . . . . . . . . . . . . Running Watts

*Air Conditioner (12,000 Btu) . . . . . . . . . . . . . . . . . 1700

*Air Conditioner (24,000 Btu) . . . . . . . . . . . . . . . . . 3800

*Air Conditioner (40,000 Btu) . . . . . . . . . . . . . . . . . 6000

Battery Charger (20 Amp) . . . . . . . . . . . . . . . . . . . . 500

Belt Sander (3") . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000

Chain Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Circular Saw (6-1/2") . . . . . . . . . . . . . . . . . .800 to 1000

*Clothes Dryer (Electric) . . . . . . . . . . . . . . . . . . . . 5750

*Clothes Dryer (Gas) . . . . . . . . . . . . . . . . . . . . . . . . 700

*Clothes Washer. . . . . . . . . . . . . . . . . . . . . . . . . . . 1150

Coffee Maker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1750

*Compressor (1 HP) . . . . . . . . . . . . . . . . . . . . . . . . 2000

*Compressor (3/4 HP) . . . . . . . . . . . . . . . . . . . . . . 1800

*Compressor (1/2 HP) . . . . . . . . . . . . . . . . . . . . . . 1400

Curling Iron. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

*Dehumidifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650

Disc Sander (9") . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Edge Trimmer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Electric Blanket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400

Electric Nail Gun. . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Electric Range (per element). . . . . . . . . . . . . . . . . .1500

Electric Skillet . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1250

*Freezer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .700

*Furnace Fan (3/5 HP) . . . . . . . . . . . . . . . . . . . . . . .875

*Garage Door Opener . . . . . . . . . . . . . . . . . . 500 to 750

Hair Dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1200

Hand Drill. . . . . . . . . . . . . . . . . . . . . . . . . . . 250 to 1100

Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .450

Impact Wrench . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500

Iron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1200

*Jet Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .800

Lawn Mower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1200

Light Bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100

Microwave Oven . . . . . . . . . . . . . . . . . . . . . 700 to 1000

*Milk Cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1100

Oil Burner on Furnace . . . . . . . . . . . . . . . . . . . . . . . .300

Oil Fired Space Heater (140,000 Btu) . . . . . . . . . . . .400

Oil Fired Space Heater (85,000 Btu) . . . . . . . . . . . . .225

Oil Fired Space Heater (30,000 Btu) . . . . . . . . . . . . .150

*Paint Sprayer, Airless (1/3 HP) . . . . . . . . . . . . . . . .600

Paint Sprayer, Airless (hand-held). . . . . . . . . . . . . . .150

Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 to 200

*Refrigerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .700

Slow Cooker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200

*Submersible Pump (1-1/2 HP) . . . . . . . . . . . . . . . .2800

*Submersible Pump (1 HP) . . . . . . . . . . . . . . . . . . .2000

*Submersible Pump (1/2 HP) . . . . . . . . . . . . . . . . .1500

*Sump Pump . . . . . . . . . . . . . . . . . . . . . . . . 800 to 1050

*Table Saw (10") . . . . . . . . . . . . . . . . . . . . 1750 to 2000

Television. . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 to 500

Toaster. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000 to 1650

Weed Trimmer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500

* Allow 3 times the listed watts for starting these devices.

3.4 — STARTING THE GENERATOR

(ELECTRIC START)

Never start or stop engine with electrical

devices plugged into the receptacles AND

devices turned on.

1. To start the engine, turn the fuel valve to the ON posi-

tion (Figure 3-2).

2. Move the choke lever to the START position (left)

(Figure 3-3).

3. Press and hold the off/run/start switch in the START

position. The engine will crank and attempt to start.

When the engine starts, release the switch to the

RUN position.

+

HomeLink 6500 Series Portable Generator 13

4. When the engine starts, move the choke lever to the

RUN position (right). If engine falters, move choke

lever back to the START position (left) until the

engine runs smoothly and then return it to the RUN

position (right).

5. This generator is also equipped with a manual recoil

starter which may be used if the battery is dis-

charged.

Figure 3-2. Fuel Valve

Figure 3-3. Choke Location

3.5 — STARTING THE GENERATOR

(MANUAL/RECOIL) STARTING

1. To start the generator, put the off/run/start switch in

the ON position.

2. Turn the fuel valve to the ON position.

3. Move the choke lever to the START position.

4. Firmly grasp the recoil handle and pull slowly until

increased resistance is felt. Pull rapidly up and away

to start engine.

5. When the engine starts, move the choke lever until

the engine runs smoothly and then fully to the RUN

position. If engine falters, pull choke lever back to

START until the engine runs smoothly and then

return to the RUN position.

NOTE: If engine fires, but does not continue to run,

move the choke lever to “Start” and repeat starting

instructions.

IMPORTANT: Do not overload the generator. Also, do

not overload individual panel receptacles. These outlets

are protected against overload with push-to-reset-type

circuit breakers. If amperage rating of any circuit breaker

is exceeded, that breaker opens and electrical output to

that receptacle is lost. Read “Generator Loads” carefully.

3.6 — STOPPING THE GENERATOR

NOTE: NEVER start or stop the engine with electrical

devices plugged in and turned on.

1. Shut off all loads, then unplug the electrical loads

from the generator’s panel receptacles or extension

cord.

2. Let the engine run at no-load for several minutes to

stabilize the internal temperatures of the engine and

generator.

3. Move the off/run/start switch to the OFF position.

4. Close the fuel valve.

3.7 — LOW OIL LEVEL SHUTDOWN

S

YSTEM

The engine is equipped with a low oil level sensor that

shuts down the engine automatically when the oil level

drops below a specified level. If the engine shuts down by

itself and the fuel tank has sufficient fuel, check engine oil

level.

000208

000209

14 HomeLink 6500 Series Portable Generator

This page intentionally left blank.

HomeLink 6500 Series Portable Generator 15

4.1 — General Recommendations

The warranty of the generator does not cover items that

have been subjected to operator abuse or negligence. To

receive full value from the warranty, the operator must

maintain the generator as instructed in this manual.

Some service procedures will be performed periodically

to properly maintain the generator.

All service procedures in the Maintenance section of this

manual should be made at the intervals indicated. Follow

the intervals in the “Service Interval Table 4-1”.

4.2 — Generator Cleaning

Generator cleaning consists of keeping the unit clean

and dry. Operate and store the unit in a clean dry envi-

ronment where it will not be exposed to excessive dust,

dirt, moisture or any corrosive vapors. Cooling air slots in

the generator must not become clogged with snow,

leaves, or any other foreign material. Check the cleanli-

ness of the generator frequently and clean when dust,

dirt, oil, moisture or other foreign substances are visible

on its exterior surface.

Never insert any object or tool through the air

cooling slots, even if the engine is not running.

4.2.1 — Generator Cleaning

• Use a damp cloth to wipe exterior surfaces clean.

• A soft, bristle brush may be used to loosen caked on

dirt, oil, etc.

• A vacuum cleaner may be used to pick up loose dirt

and debris.

• Low pressure air (not to exceed 25 psi/1.72 bar) may

be used to remove dirt. Inspect cooling air slots and

openings on the generator. These openings must be

kept clean and unobstructed.

NOTE: DO NOT use a garden hose to clean genera-

tor. Water can enter the engine fuel system and

cause problems. In addition, if water enters the gen-

erator through cooling air slots, some water will be

retained in voids and crevices of the rotor and stator

winding.

4.3 — Service Intervals

Follow the service interval table to perform scheduled

maintenance. More frequent service is required when

operating in adverse conditions as noted below.

*

Table 4-1: Service Intervals

OPERATION INTERVAL FREQUENCY

Oil Level Check Prior to every use/or every 24 hours of operation

Oil Change (break-in) After initial 30 hours of operation

Oil Change Every 100 hours of operation and/or annually

Spark Plug Replacement Every 200 hours of operation and/or annually

Air Filter Service Every 200 hours of operation and/or annually

Spark Arrestor Service Annually

Valve Clearance Adjustment (break-in) After 50 hours of operation

Valve Clearance Adjustment Every 300 hours of operation

Fuel Filter Replacement Every 500 hours of operation and/or annually

Battery Charging Every 3 months or if starter will not turn engine

Battery Replacement If it no longer accepts a charge

Storage If not used for 30 days or more/ long term

Section 4 Maintenance

16 HomeLink 6500 Series Portable Generator

4.3.1 — Engine Maintenance

When working on the generator, always dis-

connect spark plug wire from spark plug and

keep wire away from spark plug.

4.3.2 — Oil Level Check

See the “Before Starting the Generator” section for infor-

mation on Adding and checking the oil level. The oil level

should be checked before each use, or at least every

eight hours of operation. Keep the oil level maintained.

See Figure 4-1 for the dipstick and oil fill location.

4.3.3 — Oil Change

Change the oil after the first 30 hours and every 100

hours thereafter. If running this unit under dirty or dusty

conditions, or in extremely hot weather, change the oil

more often.

Hot oil may cause burns. Allow engine to cool

before draining oil. Avoid prolonged or

repeated skin exposure with used oil. Thor-

oughly wash exposed areas with soap.

Use the following instructions to change the oil after the

engine cools down:

1. Clean area around oil drain plug (Figure 4-1).

2. Remove oil drain plug from engine and oil fill plug to

drain oil completely into a suitable container.

3. When oil has completely drained, install oil drain plug

and tighten securely.

4. Fill engine with recommended oil. (See “Before Start-

ing the Generator” for oil recommendations).

5. Fill to the upper level on the dipstick (Figure 4-2).

6. Dispose of used oil at a proper collection center.

Figure 4-1. Oil Drain Plug

Figure 4-2. Oil Fill/Dipstick

4.3.4 — Spark Plug Replacement

Use a Champion N9YC spark plug or equivalent.

Replace the plug every 200 hours.

1. Stop the engine and shut off the fuel valve. Allow the

engine to cool.

2. Remove the spark plug boot from the plug and clean

that area of the cylinder head. The spark plug is

located on the side of the generator (Figure 4-3).

3. Use a 13/16 in. (21mm) spark plug tool to remove the

spark plug.

4. Set the new spark plug’s gap to 0.028-0.031 in.

(0.70-0.80 mm) (Figure 4-4).

5. Install the correctly gapped spark plug into the cylin-

der head and torque to 18-21.6 ft./lbs./24.4-29.3 Nm.

6. Reconnect the spark plug wire.

Figure 4-3. Spark Plug Location

+

*

DIPSTICK / FILL OPENING

OIL DRAIN PLUG

000116

000210

La page charge ...

Generac 6500E 0068651 Manuel utilisateur

Generac 6500E 0068651 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents