Viking VBUI Le manuel du propriétaire

Install / Use & Care

MANUAL

5 SERIES

Professional Undercounter Refrigerator / Beverage Center

Réfrigérateur de comptoir / Stockage de boissons Professionnel

Refrigerador bajo mostrador / Centro de bebidas Profesional

VRUI5240

VBUI5150

VBUI5240

FR-D’installation/d’utilisation et d’entretien

ES-De instalación/operación y mantenimiento

2

NOTE

!

CAUTION

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Product dimensions ............................................................6

Using your Electronic control .............................................8

Starting your appliance ...................................................8

Sleep mode ....................................................................8

Turning your appliance "ON" or "OFF" ...........................8

Interior display lighting ....................................................8

Adjusting the temperature ..............................................9

Temperature mode .........................................................9

Control lock ....................................................................9

Temperature sensor error codes ....................................9

Alarms ..........................................................................10

Door ajar ...................................................................10

Power failure ............................................................10

Temperature alarm ...................................................10

Vacation mode ..............................................................11

Shelving conﬁ gurations ....................................................12

Care and cleaning .............................................................15

Energy saving tips .............................................................15

Service Information .............................................................16

Troubleshooting ................................................................17

Warranty ...........................................................................18

Important Safety Instructions

Warnings and safety instructions appearing in this

guide are not meant to cover all possible conditions and

situations that may occur. Common sense, caution, and

care must be exercised when installing, maintaining, or

operating this appliance.

Recognize Safety Symbols,

Words, and Labels.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

CONTENTS

!

WARNING

WARNING - You can be killed or seriously injured

if you do not follow these instructions.

!

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

!

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

3

NOTE

!

CAUTION

XXXXXXXXXXXX

VIKING RANGE, LLC

GREENWOOD, MS 38930

!

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent

accidents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

!

WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

!

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding

internal components in place. The owners manual is

shipped inside the product in a plastic bag along with the

warranty registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance

has been thoroughly inspected and found to be in good

condition. If there is damage, the packaging will be needed

as proof of damage in transit. Afterwards please dispose of

all items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the

appliance to sit upright for a period of at least 24 hours

before plugging in. This will assure oil returns to the

compressor. Plugging the appliance in immediately may

cause damage to internal parts.

Figure 1

The following information will be

required when registering your

appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the left

side near the top. See ﬁ gure 1.

Warranty Registration

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or

you can register online at www.vikingrange.com

UNPACKING YOUR APPLIANCE

Online registration

available at

www.vikingrange.com

4

!

CAUTION

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

ensure your product performs to speciﬁ cations, the recom-

mended installation location temperature range is from 55

to 100°F (13 to 38°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unob-

structed. All Professional models with articulated hinges are

intended for built-in applications only.

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to ﬂ ow through the condenser heat ex-

changer. Restrictions to this air ﬂ ow will result in increased

energy usage and loss of cooling capacity. For this reason

it is important this area to not be obstructed and the grille

openings kept clean. Viking Range, LLC does not recom-

mend the use of a custom made grille as air ﬂ ow may be

restricted. (See Figure 2).

I NSTALLING YOUR APPLIANCE

Figure 2

Front Leveling

Legs

Front Grille,

keep this area

open.

Leveling Legs

Adjustable legs at the front and rear corners of the appli-

ance should be set so the unit is ﬁ rmly positioned on the

ﬂ oor and level from side to side and front to back. The

overall height of your appliance may be adjusted higher (by

turning the leveling leg out, CCW) and lower (by turning the

leveling leg in, CW) dimensions as shown in Table "A".

To adjust the leveling legs, place the appliance on a solid

surface and protect the ﬂ oor beneath the legs to avoid

scratching the ﬂ oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 5).

Rear

Leveling

Legs

Model

Door

Style

Minimum

Height

Maximum

Height

VRUI5240

VBUI5150

VBUI5240

(G)

33

3

⁄4"

(85.7 cm)

34

3

⁄4"

(88.3 cm)

Table A

5

NOTE

I NSTALLING YOUR APPLIANCE

Figure 5

Front grille screw

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

!

WARNING

Front grille

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 6). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

Figure 6

Figure 3

Figure 4

Do not remove

ground prong

6

"A"

"B"

"C"

"D"

"E"

PRODUCT DIMENSIONS

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

VBUI5150 15"

(38.1 cm)

**34" to 35"

(86.4 to 88.9 cm)

*

14

7

⁄8"

(37.8 cm)

33

3

⁄4" to 34

3

⁄4"

(85.7 to 88.3 cm)

23

⁄32"

(60.2 cm)

26

7

⁄32"

(66.6 cm)

37

13

⁄32"

(95 cm)

17

7

⁄16"

(44.3 cm)

VRUI5240

VBUI5240

24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm)

*

23

7

⁄8"

(60.7 cm)

33

3

⁄4" to 34

3

⁄4"

(85.7 to 88.3 cm)

23

⁄32"

(60.2 cm)

26

7

⁄32"

(66.6 cm)

46

13

⁄32"

(117.9 cm)

26

7

⁄16"

(67.2 cm)

* Depth dimension of rough-in opening may vary depending on each individual installation. To recess entire door "F" di-

mension plus 1" (2.5 cm) for thickness of power cord plug is required.

** Minimum rough-in opening required is to be larger than the adjusted height of the cabinet.

Figure 7

Figure 7a

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

Not all recessed outlet boxes will work for this applica-

tion as they are too narrow, but a recessed outlet box

equivalent to Arlington #DVFR1W is recommended for

this application, (see Figure 8).

Figure 8

7

"D"

"E"

"F"

"G"

"H"

"J"

PRODUCT DIMENSIONS

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

VBUI5150

115V/60HZ/15A

105 lbs

(47.6 kg)

VRUI5240

VBUI5240 115V/60Hz/15A

140 lbs

(63.6 kg)

3

1

⁄2" (8.9 cm)

Minimum

Figure 9

21

1

⁄2"

(54.6 cm)

# A grounded 15 amp dedicated circuit is required.

Follow all local building codes when installing

electrical and appliance.

8

Power Failure

ALARM RESET

USING YOUR ELECTRONIC CONTROL

Temp

Minus

keypad

Temp

Plus

keypad

On/Off

keypad

Display Area

Lights keypad

(glass door

only)

Lock

keypad

System Status

indicators

Figure 10

Electronic single

zone control

Starting your appliance:

Plug the appliance power cord into a 115 volt wall outlet.

Your appliance is shipped from the factory in the "On" posi-

tion and will begin start-up of cooling as soon as power is

supplied. If the appliance does not start, conﬁ rm that the

wall outlet has power, and that the control is in the "On"

position, (See "Turning your appliance On and Off" below).

The control display is covered with a clear plastic ﬁ lm. This

ﬁ lm may be removed by carefully lifting the ﬁ lm at a corner.

On initial power up, the control display will indicate a

"Power Failure" alarm. This is a normal condition as the ap-

pliance was powered-up at the factory for quality inspection

and then removed from power. A momentary press of the

"On/Off" keypad will reset this alarm condition. (See Alarms

section on page 10).

Turning your appliance ON and OFF:

If the appliance is "On", (and out of sleep mode) the tem-

perature will be shown in the display area of the control.

To turn the appliance "Off", press and hold the "On/Off"

keypad for 4-seconds. "OFF" will now be displayed on the

control.

To turn the appliance "On", press and hold the "On/Off"

keypad for 4-seconds.

Sleep mode:

If no keypads are pressed for 60 seconds, the display will

enter sleep mode to conserve power. The control panel will

go dark with the exception of the system status "OK" indi-

cator which will remain enabled. Alarm conditions will wake

the display, (see alarms on page 10).

To make the following changes to the control settings

(turning the appliance ON/OFF, adjusting the tempera-

ture, changing the interior lights, and activating vaca-

tion mode), the control must be awake.

The sleep mode can be disabled if you prefer to have the

display on continuously. Press and hold the "Lock" key-

pad until the display goes past "Loc" and reads "nSL". To

enable the sleep mode, repeat the instruction, again going

past "Loc" until the display reads "SLP".

To wake the display press any keypad. A conﬁ rm tone will

sound, and the current storage compartment temperature

will be displayed.

Interior display lighting: (Glass door models only)

Your appliance is equipped with a dual light level display

lighting feature. With the control out of sleep mode press

the "Light" keypad once to activate the interior lighting

display feature at full illumination. A conﬁ rmation tone will

sound, and the light bulb "Icon" will illuminate. Pressing

the "Light" keypad a 2nd time will dim the lighting to 50%.

A 3rd press will deactivate the display lighting feature. The

display lighting will automatically deactivate after 4-hours.

9

NOTE

If the control lock is active (illuminated lock icon)

the control will have to be unlocked before using

the keypad to reset an alarm condition. See page 9

(Control Lock) for instructions for unlocking the control.

Temperature Sensor Error Codes

Sensor Displayed Code Error Description Action to Take

Single Zone

Temperature

Sensor

Failed temperature sensor in the single

zone compartment. Can lead to

unwanted storage temperatures and/or

spoiled perishable goods.

Call service to have the

temperature sensor replaced and

remove all perishable goods from

compartment to prevent spoilage.

Defrost Sensor

Failed defrost temperature sensor.

Causes unit to not defrost properly and

can create large frost build-up. Can lead to

water damage to the unit and

surrounding ﬂ oor.

Unplug the power cord

immediately and call service to have

the defrost sensor replaced.

The temperature sensors are monitored continuously. Any

OPEN or SHORTED circuit condition will initiate an ER-

ROR CODE as listed below:

Temperature Sensor Error Codes

USING YOUR ELECTRONIC CONTROL

Temperature mode:

The temperature mode is preset from the factory in Fahren-

heit (°F) but you have the option to change it to Centigrade

(°C). To change the mode, press and hold the "-" keypad,

while pressing the "+" keypad, then release the "-" keypad.

The temperature will now be displayed in Centigrade (°C).

Repeat the procedure to change the temperature mode

back to Fahrenheit (°F).

Control lock:

The control panel can be locked to avoid unintentional

changes. To lock the control, press and hold the "Lock" key-

pad until the display reads "Loc" then immediately release

your ﬁ nger from the keypad. The lock icon will ﬂ ash 3-times

and then continuously illuminate. When the control panel is

locked, only the Lock keypad, System Status OK indicator

, and the Alarm indicator are active. To un-lock the control

panel, repeat this instruction until the display reads "nLc",

then immediately release your ﬁ nger from the keypad.

Adjusting the temperature:

To set or check the set-point temperature (with the control

out of sleep mode), press the "-" or "+" keypads. "SET" will

be indicated on the user interface panel and the current

set-point temperature will display and ﬂ ash. Subsequent

presses of the "-" or "+" keypads will adjust the temperature

colder or warmer respectively. When you have reached

your desired set-point temperature, press the "On/Off" key-

pad to accept, or do nothing and the "Set" mode will time-

out in 10-seconds accepting the displayed temperature as

the new set-point.

The available set-point temperature range for your ap-

pliance is 34°F (1.2°C) to 42°F (5.7°C). If you attempt to

adjust the temperature outside of this range you will receive

an audible notiﬁ cation.

When initially loading your product with warm contents, it

may take up to 48-hours for the storage compartment tem-

perature to stabilize.

When making temperature set-point changes, it may take

up to 24-hours for the stored contents to stabilize at your

new set-point temperature.

Factors that affect the storage compartment stabilized

temperature:

• Changes to temperature setting.

• Room temperature changes.

• Temperature of stored contents.

- Loading warm contents.

- Cold content load will delay the change to a warmer

set-point temperature.

- Warm content load will delay the change to a colder

set-point temperature.

• Usage, (number and duration of the door openings).

• Use of the storage compartment display lighting, (glass

door product only).

• Installation of the appliance in direct sunlight or next to

a heat source.

10

ALARM RESET

Power Failure

ALARM RESET

Temp

NOTE

Door Ajar

Temp

Door Ajar

ALARM RESET

This alarm condition can be reset by closing the door or

momentarily pressing the "On/Off" keypad, (i.e.-if you

are cleaning the storage compartment, etc.). The alarm

will recur in 5-minutes if the alarm condition persists.

USING YOUR ELECTRONIC CONTROL

• Power failure - If power to the appliance is inter-

rupted the System Status indicator will turn-off and

the "Power Failure" indicator will ﬂ ash. Additionally, an

"ALARM RESET" indicator will be displayed below the

"On/Off" keypad. No audible tone will sound. This alarm

condition can be reset by momentarily pressing the

"On/Off" keypad. If this alarm occurs, it is recommend-

ed that you check the condition of any perishables,

even if the appliance is operating normally and the tem-

perature has recovered, as prolonged power outages

could result in excessive temperature excursions which

may spoil perishables.

• Temperature alarm - If the storage compart-

ment temperature deviates excessively from your

set-point temperature for an extended period of time,

the "TEMP" indicator will ﬂ ash, and an audible tone

will sound every 60 seconds. Additionally, an "ALARM

RESET" indicator will be displayed below the "ON/

OFF" keypad.

Multiple alarms are possible, i.e.- "Door Ajar" for a pro-

longed period may trigger a "Temp" alarm, in which case

both "Door Ajar" and "Temp" indicators will activate.

• Door ajar - If the door is open, or not closed prop-

erly, for more than 5-minutes the System Status OK

indicator will turn-off, the "Door Ajar" indicator will ﬂ ash,

and a tone will sound every 60 seconds. Additionally,

an "ALARM RESET" indicator will be displayed below

the "On/Off" keypad.

Alarms:

The control will alert you to conditions that could adversely

affect the performance of the appliance.

This alarm condition can be reset by momentarily pressing

the "On/Off" keypad. If this alarm occurs it is recommended

that you check the condition of your stored contents, even

though the appliance is operating normally and the temper-

ature has recovered, as prolonged temperature excursions

could spoil perishables.

NOTE

The audible alarm can be muted, for each occurrence, by

pressing the lock keypad.

NOTE

The audible alarm can be muted, for each occurrence,

by pressing the lock keypad.

NOTE

After a high temperature alarm condition, check all perish-

ables to ensure they are safe for consumption.

The temperature alarm may occur as a result of high usage

or introduction of warm contents to the storage compart-

ment. If the temperature alarm continues to occur, your unit

may require service.

11

USING YOUR ELECTRONIC CONTROL

Vacation mode:

This operating mode can be used to save energy during

high cost energy periods, or when you won't be using your

appliance for an extended period of time by disabling the

lights, alarm tones, and keypad entry tones. Vacation mode

also serves as a Sabbath mode, disabling functions and

its controls in accordance with the weekly Sabbath and

religious holidays observed within the Orthodox Jewish

community. When used as Sabbath mode, you may open

or close the door at any time to access contents without

concern of directly turning on or off any lights, digital read-

outs, solenoids, fans, valves, compressor, icons, tones, or

alarms.

When activated, the display, alarm indicators and tones,

keypad touch tones, interior lights, and all options are dis-

abled. All keypad functions are disabled, with the exception

of the "On/Off" keypad which is required to exit Vacation-

mode. Storage compartment temperatures are monitored

and controlled at the settings prior to entering Vacation

mode.

To enter Vacation Mode (with the control out of sleep

mode), press and hold the "On/Off" keypad until the display

goes past "OFF" and reads "VAC". The display will ﬂ ash

"VAC" 3-times to acknowledge your request, then will

display "VAC" continuously until Vacation mode is exited.

A power outage will not exit Vacation mode, exiting can

only be accomplished manually. To exit Vacation mode and

return to normal operation, press and hold the "On/Off"

keypad until the control displays the temperature.

12

SHELVING CONFIGURATIONS

VBUI5240 Beverage Center:

VBUI5150 Beverage Center:

Loading Tips and Suggestions

Your appliance is equipped with a cantilever shelf system

which provides maximum adjust ability and customizing of

the shelving arrangements listed below.

24" (61 cm) Wide Models:

Shown with a glass overlay door. Figure 12.

15" (38.1 cm) Wide Models:

Shown with a glass door. Figure 11.

Figure 11

(2) frame and ﬂ at glass shelf. (See Figure 14).

Figure 13

VRUI5240 Refrigerator:

24" (61 cm) Wide Models:

Shown with a glass door. Figure 13.

(1) half width ﬂ at glass cantilever shelf. (See Figure 14).

(1) wine cutout and ﬂ at glass cantilever shelf.

(See Figure 15).

(1) frame and ﬂ at glass crisper cover.

(1) roll-out crisper pan

(2) wine cutout and ﬂ at glass cantilever shelf.

(See Figure 15).

(1) 5 bottle rollout display rack with vibration dampening mat

(See Figure 16).

Figure 12

To remove the crisper :

Pull out until it stops. Lift up on the front of the pan, and

remove it from the frame.

13

Figure 14

Frame and ﬂ at glass shelf

with trim

SHELVING CONFIGURATIONS

Wine shelf

underneath glass

Figure 15

Wine cutout and ﬂ at glass shelf with vibration dampening

mat, the glass can be removed for wine storage.

Figure 16

5 bottle rollout display rack with vibration dampening mat

14

Tall bottle

storage

area

To Add or Remove a Shelf

Remove stored product from the shelf. Do not try to remove

a loaded shelf from the appliance. Grasp the shelf front with

both hands, rotate the front upward and lift out. (See Figure

17b). To install a shelf insert the shelf in the appliance and

insert the top hooks into the shelf support slots and drop

the shelf down so the hooks drop over the bottom of the

slots.

Rear tang

(hook) on

shelf

Shelf support

slot

Installed shelf

tang

Make sure your cantilever shelf is secure on the shelf

supports by pressing down on the shelf before loading the

shelf.

!

CAUTION

Grasp the shelf by the front with

both hands and rotate the front

of the shelf up, then lift the shelf

up and remove the shelf from the

shelf ladders.

!

CAUTION

Never try to move a loaded shelf, remove everything from

the shelf before moving. Use both hands when moving a

shelf.

Figure 17a

Figure 17

Figure 17b

SHELVING CONFIGURATIONS

15

!

CAUTION

Front Grille

Be sure that nothing obstructs the required air ﬂ ow open-

ings in front of the cabinet. At least once or twice a year,

brush or vacuum lint and dirt from the front grille area (see

page 4).

SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

Cabinet

The painted cabinet can be washed with either a mild soap

and water and thoroughly rinsed with clear water. NEVER

use abrasive scouring cleaners.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

Care of Appliance

1. Avoid leaning on the door, you may bend the door

hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or mop-

ping near the front of the appliance. Damage to the

grille can occur.

3. Periodically clean the interior of the appliance as

needed.

4. Periodically check and/or clean the front grille as

needed.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as pos-

sible. Minimize the number of door openings while the

power is off so as not to adversely affect the appliance's

temperature.

Light assembly replacement

All models use an LED to illuminate the interior of the ap-

pliance. This component is very reliable, but should it fail,

contact a qualiﬁ ed service technician for replacement of the

LED.

The following suggestions will minimize the

cost of operating your refrigeration appliance.

1. Do not install your appliance next to a hot appliance

(cooker, dishwasher, etc.), heating air duct, or other

heat sources.

2. Install product out of direct sunlight.

3. Ensure the front grille vents at front of appliance be-

neath door are not obstructed and kept clean to allow

ventilation for the refrigeration system to expel heat.

4. Plug your appliance into a dedicated power circuit. (Not

shared with other appliances).

5. When initially loading your new product, or whenever

large quantities of warm contents are placed within

refrigerated storage compartment, minimize door

openings for the next 12 hours to allow contents to pull

down to compartment set temperature.

6. Maintaining a relatively full storage compartment will

require less appliance run time than an empty compart-

ment.

7. Ensure door closing is not obstructed by contents

stored in your appliance.

8. Allow hot items to reach room temperature before plac-

ing in product.

9. Minimize door openings and duration of door openings.

10. Use the warmest temperature control set temperature

that meets your personal preference and provides the

proper storage for your stored contents.

11. When on vacation or away from home for extended pe-

riods, set the appliance to warmest acceptable tem-

perature for the stored contents.

12. Set the control to the “off” position if cleaning the

appliance requires the door to be open for an extended

period of time.

13. For wine storage products:

When serving temperatures are not required,

return the compartment(s) set temperature to the

ideal red and white wine long term storage tem-

perature of 13°C / 55°F.

CARE AND CLEANING AND ENERGY SAVING TIPS

16

If service is required, call your authorized service agency.

Have the following information readily available:

• Model number

• Serial number

• Date purchased

• Name of dealer from whom purchased

Clearly describe the problem that you are having. If you are

unable to obtain the name of an authorized service agency,

or if you continue to have service problems, contact Viking

Range, LLC at (888) 845-4641 or write to:

VIKING RANGE, LLC

PREFERRED SERVICE

111 Front Street

Greenwood, Mississippi 38930 USA

Record the information indicated below. You will need it

if service is ever required. The serial number and model

numbers for your refrigerator are located on the upper wall,

behind the lighting:

Model No. ___________________________________

Serial No. _____________________________________

Date of Purchase ______________________________

Date Installed _________________________________

Dealer’s Name ________________________________

Address _____________________________________

__________________________________________

If service requires installation of parts, use only authorized

parts to insure protection under the warranty.

Keep this manual for future reference.

SERVICE INFORMATION

17

• Never attempt to repair or perform maintenance on

the appliance until the main electrical power has been

disconnected. Turning the appliance control "OFF"

does not remove electrical power from the units wiring.

• Replace all parts and panels before operating.

!

WARNING

Electrocution Hazard

Before You Call for Service

If the appliance appears to be malfunctioning, read

through this manual ﬁ rst. If the problem persists, check the

troubleshooting guide below. Locate the problem in the

guide and refer to the cause and its remedy before calling

for service. The problem may be something very simple

that can be solved without a service call. However, it may

be required to contact your dealer or a qualiﬁ ed service

technician.

TROUBLESHOOTING

Problem Possible Cause Remedy

Appliance not cold enough

(See “Adjusting the temperature" on

page 9)

• Control set too warm

• Content temperature not stabi-

lized.

• Excessive usage or prolonged

door openings.

• Airﬂ ow to front grille blocked.

• Door gasket not sealing properly.

• Adjust temperature colder. Al-

low 24 hours for temperature to

stabilize.

• Allow temperature to stabilize for

at least 24 hours.

• Airﬂ ow must not be obstructed to

front grille. See “clearances” on

page 4.

• Check door alignment and/or

replace door gasket.

Appliance too cold

(See “Adjusting the Temperature” on

page 9)

• Control set too cold

• Door gasket not sealing properly.

• Adjust temperature warmer.

Allow 24 hours for temperature to

stabilize.

• Check door alignment and/or

replace door gasket.

No interior light. • Failed LED light assembly or light

switch.

• Contact a qualiﬁ ed service techni-

cian.

Light will not go out when door is

closed

• Display light is turned on. (Glass

door models only.

• Door not activating light switch.

• Failed light switch

• Turn off display light, shut door.

• Appliance not level, level appli-

ance, (See page 4, “leveling legs”)

• Contact a qualiﬁ ed service techni-

cian.

Noise or Vibration • Appliance not level

• Fan hitting tube obstruction.

• Level appliance, see “Leveling

Legs” on page 4.

• Contact a qualiﬁ ed service techni-

cian.

Appliance will not run. • Appliance turned off

• Power cord not plugged in.

• No power at outlet.

• Turn appliance on. See “Starting

your appliance” on page 8.

• Plug in power cord.

• Check house circuit.

!

CAUTION

In the unlikely event you lose cooling in your unit, do not

unplug the product from the electric supply, but do call

a qualiﬁ ed service technician immediately. It is possible

that the loss of cooling capacity is a result of excessive

frost build-up on the evaporator cooling coil. In this case,

removing power to the unit will result in the melting of this

excessive quantity of ice, which could generate melt water

that exceeds the capacity of the defrost drain system and

could result in water damage to your home. The end-user

will be ultimately responsible for any water damage caused

by prematurely turning the unit off without appropriately

managing the excess water run-off.

18

HOUSEHOLD PRODUCT WARRANTY

UNDERCOUNTER REFRIGERATOR / BEVERAGE CENTER WARRANTY

TWO YEAR FULL WARRANTY

Undercounter refrigerators / Beverage Centers and all of their component parts, except as detailed below*†, are warranted to be free from defective

materials or workmanship in normal residential use for a period of two (2) years from the date of original retail purchase. Viking Range, LLC, warrantor,

agrees to repair or replace, at its option, any part which fails or is found to be defective during the warranty period.

*FULL NINETY (90) DAY COSMETIC WARRANTY: Product is warranted to be free from cosmetic defects in materials or workmanship (such

as scratches on stainless steel, paint/porcelain blemishes, etc.) for a period of ninety (90) days from the date of original retail purchase or

closing date for new construction, whichever period is longer. Any defects must be reported to the selling dealer within ninety (90) days from

date of original retail purchase. Viking Range, LLC uses high quality processes and materials available to produce all color ﬁ nishes. However,

slight color variation may be noticed because of the inherent differences in painted parts and porcelain parts as well as differences in kitchen

lighting, product locations, and other factors. Therefore, this warranty does not apply to color variation attributable to such factors.

†FULL NINETY (90) DAY WARRANTY IN “RESIDENTIAL PLUS” APPLICATIONS: This full warranty applies to applications where use

of the product extends beyond normal residential use, but the warranty period for products used in such applications is ninety (90) days.

Examples of applications covered by this warranty are bed and breakfasts, ﬁ re stations, private clubs, churches, yachts, etc. Under this

“Residential Plus” warranty, the product, its components and accessories are warranted to be free from defective material or workmanship

for a period of ninety (90) days from the date of original retail purchase. This warranty excludes use of the product in all commercial locations

such as restaurants, food service locations and institutional food service locations.

SIX YEAR FULL WARRANTY ON SEALED REFRIGERATION PARTS AS LISTED

Any sealed refrigeration system component, as listed below, is warranted to be free from defective materials or workmanship in normal household use

during the third through the sixth year from the date of original retail purchase. Viking Range, LLC, warrantor, agrees to repair or replace, at its option,

any part which fails or is found to be defective during the warranty period.

Sealed Refrigeration System Components: Compressor, Evaporator, Condenser, Connecting Tubing, Dryer/Strainer

TWELVE YEAR LIMITED WARRANTY ON SEALED REFRIGERATION PARTS AS LISTED

Any sealed refrigeration system component, as listed above, which fails due to defective materials or workmanship in normal household use during the

seventh through the twelfth year from the date of original retail purchase will be repaired or replaced, free of charge for the part itself, with the owner

paying all other costs, including labor.

TERMS AND CONDITIONS

This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner of the product during the term of

the warranty and applies to products purchased and located in the United States, Canada, Mexico and the Caribbean (excluding Cuba, Dominican

Republic, and Haiti). Products must be purchased in the country where service is requested. If the product or one of its component parts contains a

defect or malfunction during the full warranty period after a reasonable number of attempts by the warrantor to remedy the defect or malfunction, the

owner is entitled to either a refund or replacement of the product or its component part or parts. Replacement of a component part includes its free

installation, except as speciﬁ ed under the limited warranty. Under the terms of this warranty, service must be performed by a factory authorized Viking

Range, LLC service agent or representative. Service will be provided during normal business hours, and labor performed at overtime or premium rates

shall not be covered by this warranty.

Owner shall be responsible for proper installation, providing reasonable and necessary maintenance, providing proof of purchase upon request, and

making the appliance reasonably accessible for service. The return of the Owner Registration Card is not a condition of warranty coverage. You should,

however, return the Owner Registration Card so that Viking Range, LLC can contact you should any question of safety arise which could affect you.

This warranty gives you speciﬁ c legal rights, and you may also have other rights which may vary from jurisdiction to jurisdiction.

WHAT IS NOT COVERED BY THIS WARRANTY: This warranty shall not apply to damage resulting from abuse, failure to provide reasonable and

necessary maintenance, accident, delivery, negligence, natural disaster, loss of electrical power to the product for any reason, alteration, outdoor use,

improper installation, improper operation, or repair or service of the product by anyone other than an authorized Viking Range, LLC service agency or

representative. This warranty does not apply to commercial usage.

LIMITATION OF REMEDIES AND DURATION OF IMPLIED WARRANTY

OWNER’S SOLE AND EXCLUSIVE REMEDY FOR A CLAIM OF ANY KIND WITH RESPECT TO THIS PRODUCT SHALL BE THE REMEDIES

SET FORTH ABOVE. VIKING RANGE, LLC IS NOT RESPONSIBLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGE, INCLUDING BUT NOT

LIMITED TO FOOD OR MEDICINE LOSS, DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF

CONTRACT OR OTHERWISE. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusions may not apply to you. ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

APPLICABLE TO THIS PRODUCT ARE LIMITED IN DURATION TO THE PERIOD OF COVERAGE OF THE APPLICABLE EXPRESS WRITTEN

LIMITED WARRANTIES SET FORTH ABOVE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may

not apply to you.

WARRANTY SERVICE

To obtain warranty service, contact an authorized Viking Range, LLC service agent, or Viking Range, LLC, 111 Front Street, Greenwood, Mississippi

38930, (888) 845-4641. Provide model and serial number and date of original purchase or closing date for a new construction. For the name of your

nearest authorized Viking Range, LLC service agency, call Viking Range, LLC.

IMPOR

TANT: Retain proof of original purchase to establish warranty period.

Speciﬁ cations subject to change without notice.

19

058185-000B EN

Viking Range, LLC

111 Front Street

Greenwood, Mississippi 38930 USA

(662) 455-1200

For product information,

call 1-888-(845-4641)

or visit our web site at vikingrange.com

(030118)

La page charge ...

Viking VBUI Le manuel du propriétaire

Viking VBUI Le manuel du propriétaire

dans d''autres langues

Autres documents