Progress Lighting P550113-028-30 Manuel utilisateur

P550113-028-30
Progress Lighting
Marque
Progress Lighting
Modèle
P550113-028-30
Taper
Manuel utilisateur

Ce manuel convient également à

INSTALLATION INSTRUCTIONS
RE A D IMPORTANT SAFETY TIPS BEFORE PROCEEDING WITH I N S TALL AT I O N
93156987_A
2CONNECT THE WIRES. NOTE:
Attach black fixture wire(s) to
black supply wire, white fixture
wire(s) to white supply wire and
bare or green fixture ground
wire(s) to ground wire in outlet
box or green ground screw on
cross bar.
NEVER CONNECT
GREEN FIXTURE GROUND TO
BLACK OR WHITE POWER
SUPPLY WIRES.
LED Models may include the
LED-MOV1 optional surge
supressor. See wiring diagram
below for connections.
ATTACH cross bar to outlet box with outlet box screws (8-32
x 1/2, 2 slotted screws not provided)
ground wire
nipple
outlet box
screws
cross bar
outlet box
43
POSITION THE FIXTURE over the nipple and secure in place
with brass knob.
If fixture is to be
mounted in a wet
location, attach supplied
peal-n-stick gasket
around the outside edge
of the base as shown.
Trim off extra material.
Place diffuser on fixture
base and attach to base with
mounting screws (8-32x1/2,
4 combination head screw
provided). NOTE: Wet location
mounted fixture MUST be
caulked with an acrylic caulk at
the mounting screw heads and
where base of fixture meets
mounting surface. This provides
a water tight seal when fixture is
installed.
diffuser
base
caulk
mounting
screws
1
CAUTION: Do not turn on without diffuser installed. Do not touch LEDs or circuit board.
LED optics could be damaged. No lamp replacement required! Integral LED light engine
supplied. Do not remove protective cover from LED light engine.
Back Screw MountFront Screw Mount
Length = 1/4"
+ Depth of
Threaded Opening
Tamper proof #6 Flat Head Machine Screw
Four Required
(not supplied)
Self Tapping #8 Screw
Length = 1/4" + Heat Sink Thickness
Four required
(not supplied)
(not supplied)
(not supplied)
Eos Board
Thermal Pad
Supplied with
L12-AC120R & L18-AC120R
not required for L08-AC120R
Heat Sink
Through Hole for #8 Screw
Heat Sink
Threaded opening for #6 Screw
UL Conditions of Acceptability
The Eos LED Light Engine may be provided with or without lead wires. In cases where lead wires are not provided, wire leads must be evaluated for proper size,
operating temperature, and strain relief in final application. Wire connectors provided with the Eos LED Light Engine are rated to accept maximum 18 AWG wires.
The Eos LED Light Engine is provided with a polycarbonate lens that is part of the electrical enclosure. Lens must be secured to the printed circuit board
in the final application.
Temperature must be considered in the final application. The following temperature ratings must not be exceeded:
- Printed Circuit Board – 130˚C - Leads – as marked on the insulation
- Polycarbonate Lens (Enclosure) – 80˚C - Connectors – 125˚C
The Eos LED Light Engine must be properly heatsunk to thermal dissipation material. Do not mount the Eos board to insulating material such as glass, steel, plastic,
All Eos LED Light Engine boards are supplied with built in surge protection that provides Energy Star required transient voltage protection of 2.5Kv as outlined in
ANSI/IEEE C62.41.1-2002 and considered sufficient for indoor applications. For outdoor applications where products are at higher risk of surges from lightning it is
recommended to use a higher level of surge protection. To accomplish this, Inter-Global includes a supplementary surge protection device (LED-MOV1) which aids to
provide the transient voltage protection of 4.0Kv that is recommended for those applications.
Application Notes
Maximum solder point temperature of LEDs must not exceed 100˚C.
ENERGY STAR - Product is listed on the Energy Star Certified Component Database (CSD) under LED Light Engines. The CSD supports the Luminaire Manufacturer's
qualification of their Energy Star Luminiares by providing certified performance data of the components. This streamlines the Energy Star qualification process for the
luminaire when CSD listed productsare used.
3. TYPICAL MOUNTING DETAIL:
Product must be installed with supplied optical lens to comply with UL requirements. Lens must be hand tightened to avoid cracking.
FLICKER - All lighting systems produce Flicker. Visibility of flicker is highly arbitrary and depends on the surrounding conditions. Visual perception of flicker is negligible
at operating frequencies higher than 100Hz. Operating frequencies less than 65Hz are considered unacceptable. The Eos LED Light Engine has an operating
frequency greater than 120Hz.
Eos boards are static sensitive. They must be handled in a manner to protect them from static discharge.
If additional technical assistance is needed, please contact Inter-Global at 1-800-325-7364.
Warranty
Inter-Global warrants that its Eos product shall be free from defects in material and workmanship and will be of the designated kind and quality for a period of 5 years
from the date of manufacture.
Inter-Global makes no warranty whatsoever with respect to any Eos product not installed and operated in accordance with the current edition of the National Electrical
Code, the standards of safety of Underwriters Laboratories, the standards of the American National Standards Institute and specific instructions provided by Inter-Global
for installation and operation.
If it appears within the said warranty period that any Inter-Global Eos product does not meet the warranty specified above, the customer must give written notice of their
warranty claim and return the Eos product with approved Return Authorization (RGA) Number, at the customer’s expense to Inter-Global. Within sixty (60) days of
receipt, Inter-Global shall at its expense and option correct any defects by either repairing or replacing the defective part(s).
This warranty is not applicable to any product subjected to abnormal stresses, abuse, misuse or damage resulting from acts of god.
LED-MOV1 WIRING DIAGRAM
LED-MOV1
ELECTRIC
SUPPLY BOX
BLACK
WHITE
GREEN GROUND
BLACK
WHITE
GREEN GROUND
wire connectors
(provided)
ground wire
brass
knob
cross bar
trim extra gasket
peal-n-stick
gasket
TURN OFF
POWER SOURCE
Place wall switch in off position, if fixture
has built-in switch or chain pull, switch or
pull chain so fixture is off.
SAFETY TIPS
INSTALLATION INSTRUCTIONS
RE A D IMP O R TAN T S A FETY T I P S B EFORE PRO C EEDING WITH I N S TALLATION
93156987_A
2CONNECT THE WIRES. NOTE:
Attach black fixture wire(s) to
black supply wire, white fixture
wire(s) to white supply wire and
bare or green fixture ground
wire(s) to ground wire in outlet
box or green ground screw on
cross bar. NEVER CONNECT
GREEN FIXTURE GROUND
TO BLACK OR WHITE
POWER
SUPPLY WIRES.
LED Models may include the
LED-MOV1 optional surge
supressor. See wiring diagram
below for connections.
ATTACH cross bar to outlet box with outlet box screws (8-32
x 1/2, 2 slotted screws not provided)
ground wire
nipple
outlet box
screws
cross bar
outlet box
43
POSITION THE FIXTURE over the nipple and secure in place
with brass knob.
If fixture is to be
mounted in a wet
location, attach supplied
peal-n-stick gasket
around the outside edge
of the base as shown.
Trim off extra material.
Place diffuser on fixture
base and attach to base with
mounting screws (8-32x1/2,
4 combination head screw
provided). NOTE: Wet location
mounted fixture MUST be
caulked with an acrylic caulk at
the mounting screw heads and
where base of fixture meets
mounting surface. This provides
a water tight seal when fixture is
installed.
diffuser
base
caulk
mounting
screws
1
CAUTION: Do not turn on without diffuser installed. Do not touch LEDs or circuit board.
LED optics could be damaged. No lamp replacement required! Integral LED light engine
supplied. Do not remove protective cover from LED light engine.
Back Screw MountFront Screw Mount
Length = 1/4"
+ Depth of
Threaded Opening
Tamper proof #6 Flat Head Machine Screw
Four Required
(not supplied)
Self Tapping #8 Screw
Length = 1/4" + Heat Sink Thickness
Four required
(not supplied)
(not supplied)
(not supplied)
Eos Board
Thermal Pad
Supplied with
L12-AC120R & L18-AC120R
not required for L08-AC120R
Heat Sink
Through Hole for #8 Screw
Heat Sink
Threaded opening for #6 Screw
UL Conditions of Acceptability
The Eos LED Light Engine may be provided with or without lead wires. In cases where lead wires are not provided, wire leads must be evaluated for proper size,
operating temperature, and strain relief in final application. Wire connectors provided with the Eos LED Light Engine are rated to accept maximum 18 AWG wires.
The Eos LED Light Engine is provided with a polycarbonate lens that is part of the electrical enclosure. Lens must be secured to the printed circuit board
in the final application.
Temperature must be considered in the final application. The following temperature ratings must not be exceeded:
- Printed Circuit Board – 130˚C - Leads – as marked on the insulation
- Polycarbonate Lens (Enclosure) – 80˚C - Connectors – 125˚C
The Eos LED Light Engine must be properly heatsunk to thermal dissipation material. Do not mount the Eos board to insulating material such as glass, steel, plastic,
All Eos LED Light Engine boards are supplied with built in surge protection that provides Energy Star required transient voltage protection of 2.5Kv as outlined in
ANSI/IEEE C62.41.1-2002 and considered sufficient for indoor applications. For outdoor applications where products are at higher risk of surges from lightning it is
recommended to use a higher level of surge protection. To accomplish this, Inter-Global includes a supplementary surge protection device (LED-MOV1) which aids to
provide the transient voltage protection of 4.0Kv that is recommended for those applications.
Application Notes
Maximum solder point temperature of LEDs must not exceed 100˚C.
ENERGY STAR - Product is listed on the Energy Star Certified Component Database (CSD) under LED Light Engines. The CSD supports the Luminaire Manufacturer's
qualification of their Energy Star Luminiares by providing certified performance data of the components. This streamlines the Energy Star qualification process for the
luminaire when CSD listed productsare used.
3. TYPICAL MOUNTING DETAIL:
Product must be installed with supplied optical lens to comply with UL requirements. Lens must be hand tightened to avoid cracking.
FLICKER - All lighting systems produce Flicker. Visibility of flicker is highly arbitrary and depends on the surrounding conditions. Visual perception of flicker is negligible
at operating frequencies higher than 100Hz. Operating frequencies less than 65Hz are considered unacceptable. The Eos LED Light Engine has an operating
frequency greater than 120Hz.
Eos boards are static sensitive. They must be handled in a manner to protect them from static discharge.
If additional technical assistance is needed, please contact Inter-Global at 1-800-325-7364.
Warranty
Inter-Global warrants that its Eos product shall be free from defects in material and workmanship and will be of the designated kind and quality for a period of 5 years
from the date of manufacture.
Inter-Global makes no warranty whatsoever with respect to any Eos product not installed and operated in accordance with the current edition of the National Electrical
Code, the standards of safety of Underwriters Laboratories, the standards of the American National Standards Institute and specific instructions provided by Inter-Global
for installation and operation.
If it appears within the said warranty period that any Inter-Global Eos product does not meet the warranty specified above, the customer must give written notice of their
warranty claim and return the Eos product with approved Return Authorization (RGA) Number, at the customer’s expense to Inter-Global. Within sixty (60) days of
receipt, Inter-Global shall at its expense and option correct any defects by either repairing or replacing the defective part(s).
This warranty is not applicable to any product subjected to abnormal stresses, abuse, misuse or damage resulting from acts of god.
LED-MOV1 WIRING DIAGRAM
LED-MOV1
ELECTRIC
SUPPLY BOX
BLACK
WHITE
GREEN GROUND
BLACK
WHITE
GREEN GROUND
wire connectors
(provided)
ground wire
brass
knob
cross bar
trim extra gasket
peal-n-stick
gasket
TURN OFF
POWER SOURCE
Place wall switch in off position, if fixture
has built-in switch or chain pull, switch or
pull chain so fixture is off.
SAFETY TIPS
Clean only with mild soap and water. Avoid spraying with Cleansers, Insecticides,
and Pesticides that are petroleum based hydrocarbon products.
degrade Luminaire.
These will
Clean only with mild soap and water. Avoid spraying with Cleansers, Insecticides,
and Pesticides that are petroleum based hydrocarbon products.
degrade Luminaire.
These will
3. TYPICAL MOUNTING DETAIL:
Inter-Global warrants that its Eos product shall be free from defects in material and workmanship and will be of the designate
from the date of manufacture.
Inter-Global makes no warranty whatsoever with respect to any Eos product not installed and operated in accordance with the cur
Code, the standards of safety of Underwriters Laboratories, the standards of the American National Standards Institute and spec
for installation and operation.
If it appears within the said warranty period that any Inter-Global Eos product does not meet the warranty specified above, the
warranty claim and return the Eos product with approved Return Authorization (RGA) Number, at the customer’s expense to Inter-G
receipt, Inter-Global shall at its expense and option correct any defects by either repairing or replacing the defective part(s
This warranty is not applicable to any product subjected to abnormal stresses, abuse, misuse or damage resulting from acts of
Led ArrayLed Array
ditions. Visual perception of flicker is negligible
customer must give written notice of their
INSTRUCTIONS D'INSTALLATION
LIRE LES CONSEILS DE SÉCURITÉ IMPORTANTS AVANT DE PROCÉDER À L'INSTALLATION
93156987_A
Nettoyer uniquement avec du savon doux et de l'eau. Évitez de pulvériser avec des
nettoyants, des insecticides et des pesticides qui sont des produits d'hydrocarbures
à base de pétrole. Ceux-ci dégraderont Luminare.
2
CONNECTEZ LES FILS. REMARQUE :
Fixez le(s) fil(s) noir(s) du luminaire au
fil d'alimentation noir, le(s) fil(s) blanc(s) du
luminaire au fil d'alimentation blanc et le(s)
fil(s) de terre nu ou vert du luminaire au fil
de terre dans la boîte de sortie ou la vis de
terre verte sur la barre transversale.
NE JAMAIS CONNECTER LA MIS À LA
TERRE DU LUMINAIRE VERT AUX
FILS D'ALIMENTATION NOIRS OU BLANCS.
Les modèles LED peuvent inclure le
suppresseur de surtension LED-MOV1 en
option. Voir le schéma de câblage
ci-dessous pour les connexions.
Fixez la barre transversale à la boîte de sortie avec les vis
de la boîte de sortie (8-32 x 1/2, 2 vis à fente non fournies)
fil de terre
mamelon
vis de la boîte
de sortie
barre transversale
boîte de sortie
43
POSITIONNEZ LE LUMINAIRE sur le mamelon et fixez-le en
place avec le bouton en laiton.
Si le luminaire doit être
monté dans un endroit
humide, fixez le joint pelable
fourni autour du bord extérieur
de la base, comme illustré.
Coupez le matériel
supplémentaire.
Placez le diffuseur sur la base du
luminaire et fixez-le à la base
avec des vis de montage
(8-32x1/2, 4 vis à tête combinée
fournies). REMARQUE : Le
luminaire monté dans un endroit
humide DOIT être calfeutré avec
un mastic acrylique au niveau
des têtes de vis de montage et à
l'endroit où la base du luminaire
rencontre la surface de montage.
Cela fournit un joint étanche à
l'eau lorsque le luminaire est
installé.
diffuseur
base
calfater
Vis de montage
1
ATTENTION : Ne pas allumer sans diffuseur installé. Ne touchez pas les LED ou le circuit
imprimé. Les optiques LED pourraient être endommagées. Aucun remplacement de
lampe requis ! Moteur d'éclairage LED intégré fourni. Ne retirez pas le couvercle de
protection du moteur d'éclairage LED.
Back Screw MountFront Screw Mount
Length = 1/4"
+ Depth of
Threaded Opening
Tamper proof #6 Flat Head Machine Screw
Four Required
(not supplied)
Self Tapping #8 Screw
Length = 1/4" + Heat Sink Thickness
Four required
(not supplied)
(not supplied)
(not supplied)
Eos Board
Thermal Pad
Supplied with
L12-AC120R & L18-AC120R
not required for L08-AC120R
Heat Sink
Through Hole for #8 Screw
Heat Sink
Threaded opening for #6 Screw
UL Conditions of Acceptability
The Eos LED Light Engine may be provided with or without lead wires. In cases where lead wires are not provided, wire leads must be evaluated for proper size,
operating temperature, and strain relief in final application. Wire connectors provided with the Eos LED Light Engine are rated to accept maximum 18 AWG wires.
The Eos LED Light Engine is provided with a polycarbonate lens that is part of the electrical enclosure. Lens must be secured to the printed circuit board
in the final application.
Temperature must be considered in the final application. The following temperature ratings must not be exceeded:
- Printed Circuit Board – 130˚C - Leads – as marked on the insulation
- Polycarbonate Lens (Enclosure) – 80˚C - Connectors – 125˚C
The Eos LED Light Engine must be properly heatsunk to thermal dissipation material. Do not mount the Eos board to insulating material such as glass, steel, plastic,
All Eos LED Light Engine boards are supplied with built in surge protection that provides Energy Star required transient voltage protection of 2.5Kv as outlined in
ANSI/IEEE C62.41.1-2002 and considered sufficient for indoor applications. For outdoor applications where products are at higher risk of surges from lightning it is
recommended to use a higher level of surge protection. To accomplish this, Inter-Global includes a supplementary surge protection device (LED-MOV1) which aids to
provide the transient voltage protection of 4.0Kv that is recommended for those applications.
Application Notes
Maximum solder point temperature of LEDs must not exceed 100˚C.
ENERGY STAR - Product is listed on the Energy Star Certified Component Database (CSD) under LED Light Engines. The CSD supports the Luminaire Manufacturer's
qualification of their Energy Star Luminiares by providing certified performance data of the components. This streamlines the Energy Star qualification process for the
luminaire when CSD listed productsare used.
3. TYPICAL MOUNTING DETAIL:
Product must be installed with supplied optical lens to comply with UL requirements. Lens must be hand tightened to avoid cracking.
FLICKER - All lighting systems produce Flicker. Visibility of flicker is highly arbitrary and depends on the surrounding conditions. Visual perception of flicker is negligible
at operating frequencies higher than 100Hz. Operating frequencies less than 65Hz are considered unacceptable. The Eos LED Light Engine has an operating
frequency greater than 120Hz.
Eos boards are static sensitive. They must be handled in a manner to protect them from static discharge.
If additional technical assistance is needed, please contact Inter-Global at 1-800-325-7364.
Warranty
Inter-Global warrants that its Eos product shall be free from defects in material and workmanship and will be of the designated kind and quality for a period of 5 years
from the date of manufacture.
Inter-Global makes no warranty whatsoever with respect to any Eos product not installed and operated in accordance with the current edition of the National Electrical
Code, the standards of safety of Underwriters Laboratories, the standards of the American National Standards Institute and specific instructions provided by Inter-Global
for installation and operation.
If it appears within the said warranty period that any Inter-Global Eos product does not meet the warranty specified above, the customer must give written notice of their
warranty claim and return the Eos product with approved Return Authorization (RGA) Number, at the customer’s expense to Inter-Global. Within sixty (60) days of
receipt, Inter-Global shall at its expense and option correct any defects by either repairing or replacing the defective part(s).
This warranty is not applicable to any product subjected to abnormal stresses, abuse, misuse or damage resulting from acts of god.
SCHÉMA DE CÂBLAGE LED-MOV1
LED-MOV1
BOÎTIER
D'ALIMENTATION
ÉLECTRIQUE
NOIR
BLANC
TERRAIN VERT
connecteurs de fils
(fournis)
fil de terre
bouton
en laiton
barre
transversale
trim extra gasket
joint pelable
et collant
ÉTEINDRE
SOURCE D'ÉNERGIE
Placez l'interrupteur mural en position
d'arrêt, si le luminairea un interrupteur
intégré ou une traction à chaîne, un
interrupteur ou tirez la chaîne pour que le
luminaire soit éteint.
CONSEILS DE SÉCURITÉ
NOIR
BLANC
TERRAIN VERT
AU
DÉSACTIVÉ
INSTRUCTIONS D'INSTALLATION
LIRE LES CONSEILS DE SÉCURITÉ IMPORTANTS AVANT DE PROCÉDER À L'INSTALLATION
93156987_A
Nettoyer uniquement avec du savon doux et de l'eau. Évitez de pulvériser avec des
nettoyants, des insecticides et des pesticides qui sont des produits d'hydrocarbures
à base de pétrole. Ceux-ci dégraderont Luminare.
2
CONNECTEZ LES FILS. REMARQUE :
Fixez le(s) fil(s) noir(s) du luminaire au
fil d'alimentation noir, le(s) fil(s) blanc(s) du
luminaire au fil d'alimentation blanc et le(s)
fil(s) de terre nu ou vert du luminaire au fil
de terre dans la boîte de sortie ou la vis de
terre verte sur la barre transversale.
NE JAMAIS CONNECTER LA MISE À LA
TERRE DU LUMINAIRE VERT AUX
FILS D'ALIMENTATION NOIRS OU BLANCS.
Les modèles LED peuvent inclure le
suppresseur de surtension LED-MOV1 en
option. Voir le schéma de câblage
ci-dessous pour les connexions.
Fixez la barre transversale à la boîte de sortie avec les vis
de la boîte de sortie (8-32 x 1/2, 2 vis à fente non fournies)
fil de terre
mamelon
vis de la boîte
de sortie
barre transversale
boîte de sortie
43
POSITIONNEZ LE LUMINAIRE sur le mamelon et fixez-le en
place avec le bouton en laiton.
Si le luminaire doit être
monté dans un endroit
humide, fixez le joint pelable
fourni autour du bord extérieur
de la base, comme illustré.
Coupez le matériel
supplémentaire.
Placez le diffuseur sur la base du
luminaire et fixez-le à la base
avec des vis de montage
(8-32x1/2, 4 vis à tête combinée
fournies). REMARQUE : Le
luminaire monté dans un endroit
humide DOIT être calfeutré avec
un mastic acrylique au niveau
des têtes de vis de montage et à
l'endroit où la base du luminaire
rencontre la surface de montage.
Cela fournit un joint étanche à
l'eau lorsque le luminaire est
installé.
diffuseur
base
calfater
Vis de montage
1
ATTENTION : Ne pas allumer sans diffuseur installé. Ne touchez pas les LED ou le circuit
imprimé. Les optiques LED pourraient être endommagées. Aucun remplacement de
lampe requis ! Moteur d'éclairage LED intégré fourni. Ne retirez pas le couvercle de
protection du moteur d'éclairage LED.
Back Screw MountFront Screw Mount
Length = 1/4"
+ Depth of
Threaded Opening
Tamper proof #6 Flat Head Machine Screw
Four Required
(not supplied)
Self Tapping #8 Screw
Length = 1/4" + Heat Sink Thickness
Four required
(not supplied)
(not supplied)
(not supplied)
Eos Board
Thermal Pad
Supplied with
L12-AC120R & L18-AC120R
not required for L08-AC120R
Heat Sink
Through Hole for #8 Screw
Heat Sink
Threaded opening for #6 Screw
UL Conditions of Acceptability
The Eos LED Light Engine may be provided with or without lead wires. In cases where lead wires are not provided, wire leads must be evaluated for proper size,
operating temperature, and strain relief in final application. Wire connectors provided with the Eos LED Light Engine are rated to accept maximum 18 AWG wires.
The Eos LED Light Engine is provided with a polycarbonate lens that is part of the electrical enclosure. Lens must be secured to the printed circuit board
in the final application.
Temperature must be considered in the final application. The following temperature ratings must not be exceeded:
- Printed Circuit Board – 130˚C - Leads – as marked on the insulation
- Polycarbonate Lens (Enclosure) – 80˚C - Connectors – 125˚C
The Eos LED Light Engine must be properly heatsunk to thermal dissipation material. Do not mount the Eos board to insulating material such as glass, steel, plastic,
All Eos LED Light Engine boards are supplied with built in surge protection that provides Energy Star required transient voltage protection of 2.5Kv as outlined in
ANSI/IEEE C62.41.1-2002 and considered sufficient for indoor applications. For outdoor applications where products are at higher risk of surges from lightning it is
recommended to use a higher level of surge protection. To accomplish this, Inter-Global includes a supplementary surge protection device (LED-MOV1) which aids to
provide the transient voltage protection of 4.0Kv that is recommended for those applications.
Application Notes
Maximum solder point temperature of LEDs must not exceed 100˚C.
ENERGY STAR - Product is listed on the Energy Star Certified Component Database (CSD) under LED Light Engines. The CSD supports the Luminaire Manufacturer's
qualification of their Energy Star Luminiares by providing certified performance data of the components. This streamlines the Energy Star qualification process for the
luminaire when CSD listed productsare used.
3. TYPICAL MOUNTING DETAIL:
Product must be installed with supplied optical lens to comply with UL requirements. Lens must be hand tightened to avoid cracking.
FLICKER - All lighting systems produce Flicker. Visibility of flicker is highly arbitrary and depends on the surrounding conditions. Visual perception of flicker is negligible
at operating frequencies higher than 100Hz. Operating frequencies less than 65Hz are considered unacceptable. The Eos LED Light Engine has an operating
frequency greater than 120Hz.
Eos boards are static sensitive. They must be handled in a manner to protect them from static discharge.
If additional technical assistance is needed, please contact Inter-Global at 1-800-325-7364.
Warranty
Inter-Global warrants that its Eos product shall be free from defects in material and workmanship and will be of the designated kind and quality for a period of 5 years
from the date of manufacture.
Inter-Global makes no warranty whatsoever with respect to any Eos product not installed and operated in accordance with the current edition of the National Electrical
Code, the standards of safety of Underwriters Laboratories, the standards of the American National Standards Institute and specific instructions provided by Inter-Global
for installation and operation.
If it appears within the said warranty period that any Inter-Global Eos product does not meet the warranty specified above, the customer must give written notice of their
warranty claim and return the Eos product with approved Return Authorization (RGA) Number, at the customer’s expense to Inter-Global. Within sixty (60) days of
receipt, Inter-Global shall at its expense and option correct any defects by either repairing or replacing the defective part(s).
This warranty is not applicable to any product subjected to abnormal stresses, abuse, misuse or damage resulting from acts of god.
SCHÉMA DE CÂBLAGE LED-MOV1
LED-MOV1
BOÎTIER
D'ALIMENTATION
ÉLECTRIQUE
NOIR
BLANC
TERRAIN VERT
connecteurs de fils
(fournis)
fil de terre
bouton
en laiton
barre
transversale
trim extra gasket
joint pelable
et collant
ÉTEINDRE
SOURCE D'ÉNERGIE
Placez l'interrupteur mural en position
d'arrêt, si le luminairea un interrupteur
intégré ou une traction à chaîne, un
interrupteur ou tirez la chaîne pour que le
luminaire soit éteint.
CONSEILS DE SÉCURITÉ
NOIR
BLANC
TERRAIN VERT
AU
DÉSACTIVÉ
Led PRODUIT LED PRODUIT
  • Page 1 1
  • Page 2 2

Progress Lighting P550113-028-30 Manuel utilisateur

P550113-028-30
Progress Lighting
Marque
Progress Lighting
Modèle
P550113-028-30
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Autres documents