NAPOLEON Allure NEFL60FH Installation And Operating Instructions Manual

EN

W415-1542 / A / 10.06.15

FR

PG

27

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

1.16E

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonﬁ replaces.com •[email protected]

SAFETY INFORMATION

!WARNING

If the information in these instructions

are not followed exactly, a ﬁ re may result

causing property damage, personal injury

or loss of life.

- Do not store or use gasoline or other ﬂ ammable

vapors and liquids in the vicinity of this or any

other appliance.

$10.00

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA C22.2 No-46 / UL 1278

NEFL32FH, NEFL42FH, NEFL50FH,

NEFL60FH, NEFL72FH, NEFL100FH

ELECTRIC FIREPLACE

EN

W415-1542 / A / 10.06.15

2

TABLE OF CONTENTS

1.0 INTRODUCTION 3

1.1 DIMENSIONS 4

1.2 LISTING APPROVALS 4

1.3 GENERAL INSTRUCTIONS 5

1.4 UNPACKING AND TESTING APPLIANCE 5

1.5 HARDWARE PARTS LIST 6

1.6 RATING PLATE INFORMATION 7

2.0 LOCATING APPLIANCE 8

2.1 GROUNDING APPLIANCE 8

3.0 INSTALLATION 9

3.1 MINIMUM CLEARANCE TO COMBUSTIBLES 9

3.2 MINIMUM MANTEL CLEARANCES 9

3.3 INSTALLING THE APPLIANCE ONTO THE WALL 10

3.3.1 MINIMUM CLEARANCE TO COMBUSTIBLES 11

3.3.2 FRAMING 11

3.4 RECESSING THE APPLIANCE INTO THE WALL 12

3.4.1 INSTALLING THE APPLIANCE INTO A MANTEL 13

3.4.2 RUBBER FEET INSTALLATION 14

3.5 HARD WIRING INSTALLATION 15

4.0 FINISHING 16

4.1 FRONT GLASS INSTALLATION 16

4.2 FRONT GLASS REMOVAL 17

4.3 CRYSTAL EMBER INSTALLATION 17

5.0 OPERATING INSTRUCTIONS 18

5.1 MAIN POWER BUTTON 18

5.2 OPERATING TOUCH DISPLAY PANEL AND REMOTE CONTROL 18

6.0 MAINTENANCE 19

6.1 REMOTE BATTERY INSTALLATION 19

7.0 WIRING DIAGRAM 20

8.0 REPLACEMENT PARTS 22

9.0 TROUBLESHOOTING 23

10.0 WARRANTY 24

11.0 NOTES 25

EN

W415-1542 / A / 10.06.15

3

1.0 INTRODUCTION !

WARNING

3.7C

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF

CONTACTED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate

appliance according to operating instructions could cause ﬁ re or injury.

• Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before

servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet.

• Do not install damaged, incomplete or substitute components.

• Do not burn wood or other materials in this appliance.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier

is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,

install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the

room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and

draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• It is imperative that the control compartments, circulating blower and its passageway in the appliance

and are kept clean. The appliance should be inspected before use and at least annually by a qualiﬁ ed

service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding

material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and

other ﬂ ammable vapors and liquids.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the

glass should be done by a licensed or qualiﬁ ed service person.

• Do not strike or slam shut the appliance glass door.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Servicing should be done only while the appliance is disconnected from the power supply circuit.

• Always unplug appliance when not in use.

• Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been

dropped or damaged in any manner. Return appliance to authorized service facility for examination,

electrical or mechanical adjustment, or repair.

• Do not use outdoors.

• Never locate appliance where it may fall into a bathtub or other water container.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord

away from trafﬁ c area and where it will not be tripped over.

• Connect to properly grounded outlets only.

• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an

electric shock or ﬁ re, or damage the appliance.

• To prevent a possible ﬁ re, do not block air intakes or exhaust in any manner. Do not use on soft

surfaces, like a carpet, where openings may become blocked.

• Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or

relocatable power tap (outlet/power strip).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,

discolouration or damage to decorations, a T.V. or other electronic components.

EN

W415-1542 / A / 10.06.15

4

1.1 DIMENSIONS

1.2 LISTING APPROVALS

This appliance has been tested in accordance with the CSA Standards for ﬁ xed and location-dedicated electric

room appliances in the United States and Canada. If you need assistance during installation, please contact

your local dealer.

NOTE: This appliance must be electrically wired and grounded in accordance with local codes or,

in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition in the United

States or the Canadian Electric Code, CSA C22.1 in Canada.

Description Electric Fireplace

Type 3 Way Mounting Unit

Wall-Mount, Recess into Wall and

Assemble with mantel

Voltage 120V AC

Watts MAX 1500W

Amps 15 AMP Grounded Circuit

MODEL NO. NET WEIGHT GROSS WEIGHT

NEFL32FH 34.6 lbs (15.7kg) 48 lbs (21.8kg)

NEFL42FH 45.2 lbs (20.5kg) 60 lbs (27.3kg)

NEFL50FH 50.9 lbs (23.1kg) 69.4 lbs (31.5kg)

NEFL60FH 61.3 lbs (27.8kg) 82.4 (37.4kg)

NEFL72FH 87.3 (39.6kg) 115.7 (52.5kg)

NEFL100FH 118.6 (53.8kg) 156.5 (71kg)

A

B

G

F

E

D

C

DIMENSIONS

MODEL NUMBER A B C D E F G

NEFL32FH 32"

(813mm) 21 5/8"

(550mm) 5"

(127mm) 20 1/2"

(520mm) 27 5/16"

(694mm) 12"

(304mm) 22 5/16"

(567mm)

NEFL42FH 42"

(1067mm) 21 5/8"

(550mm) 5"

(127mm) 20 1/2"

(520mm) 37 1/2"

(951mm) 12"

(304mm) 32 5/16"

(821mm)

NEFL50FH 50"

(1270mm) 21 5/8"

(550mm) 5"

(127mm) 20 1/2"

(520mm) 45 7/16"

(1154mm) 12"

(304mm) 40 5/16"

(1024mm)

NEFL60FH 60"

(1524mm) 21 5/8"

(550mm) 5"

(127mm) 20 1/2"

(520mm) 55 5/16"

(1405mm) 12"

(304mm)) 50 5/16"

(1278mm)

NEFL72FH 72"

(1830mm) 21 5/8"

(550mm) 5"

(127mm) 20 1/2"

(520mm) 67 3/8"

(1711mm) 12"

(304mm) 62 5/8"

(1583mm)

NEFL100FH 100"

(2540mm) 21 5/8"

(550mm) 5"

(127mm) 20 1/2"

(520mm) 95 3/8"

(2422mm) 12"

(304mm) 90 9/16"

(2300mm)

EN

W415-1542 / A / 10.06.15

5

1.3 GENERAL INSTRUCTIONS

4.8B

A. Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the

outlet are on.

B. The appliance may emit a slight, harmless odour when ﬁ rst used. This odour is normal and it is caused

by the initial heating of internal appliance elements and will not occur again.

C. If your appliance does not emit heat, consult the operation section of this manual for further

information.

D. Use with a CSA- or UL-certiﬁ ed surge protector.

E. Do not route the power cord directly underneath the appliance.

This electric appliance meets the construction and safety standards of H.U.D. for application in manufactured

homes when installed according to these instructions.

!

WARNING

READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO

FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY

AND/OR PROPERTY DAMAGE.

ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE

IT IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL

ACCESSORIES LISTED IN THESE INSTRUCTIONS. USE OF OPTIONAL ACCESSORIES NOT

SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR

RESULT IN A SAFETY HAZARD.

DO NOT OPEN. RISK OF ELECTRIC SHOCK. NO USER-SERVICEABLE PARTS INSIDE.

DO NOT USE DAMAGED ELECTRICAL CORDS.

SERVICING SHOULD BE DONE ONLY WHILE THE APPLIANCE IS DISCONNECTED FROM THE

POWER SUPPLY CIRCUIT.

TO PREVENT ELECTRIC SHOCK MATCH THE WIDE BLADE OF PLUG TO WIDE SLOT OF

RECEPTACLE AND FULLY INSERT.

As with most electronic devices, your new electric ﬁ replace has been designed to operate at

temperatures between 5°C (41°F) and 35° C (95°F). During the colder winter months, allow the ﬁ replace

to reach room temperature before turning it on.

1.4 UNPACKING AND TESTING APPLIANCE

Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance

operates properly by plugging the power supply cord into a conveniently located 120 Volt, 15 Amp grounded

outlet.

NOTE: The NEFL50/60/72/100FH appliances are shipped with the front glass not assembled onto the

appliance. Refer to the "FRONT GLASS INSTALLATION" sections for assembly.

EN

W415-1542 / A / 10.06.15

6

1.5 HARDWARE PARTS LIST

A - Fireplace

NEFL32FH-100FH ( 1 )

B - Wood Screws

NEFL32FH-50FH ( 6 )

NEFL60FH-72FH (12)

NEFL100FH (16)

C - Drywall Anchors

NEFL32FH-50FH ( 6 )

NEFL60FH-72FH (12)

NEFL100FH (16)

D - ST4x12 Metal Screws

NEFL32FH-100FH ( 8 ) E - Remote Control

NEFL32FH-100FH ( 1 )

F - Wall Bracket

NEFL32FH-50FH ( 1 )

NEFL60FH-100FH ( 2 )

G-Crystals

NEFL32FH-100FH ( 2 ) H-CoverPlate

NEFL32FH-100FH ( 1 ) I - Strain Relief

NEFL32FH-100FH ( 1 )

J - Metal Bracket

NEFL32FH-100FH ( 4 ) K - Cord Corner

NEFL32FH-100FH ( 2 ) L - Cord Corner

NEFL32FH-100FH ( 2 )

M - Cord Cover

NEFL32FH ( 2 )

NEFL42FH-100FH ( 1 )

N - Rubber Foot

NEFL32FH-50FH ( 4 )

NEFL60FH-100FH ( 6 )

EN

W415-1542 / A / 10.06.15

7

1.6 RATING PLATE INFORMATION

INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to

the model of the appliance.

This illustration is for reference only. Refer to the rating plate on the appliance for accurate

information.

NOTE: The rating plate must remain with the appliance at all times. It must not be removed.

W385-2095

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARD: CSA 22.2 NO. 46 AND UL 2021 / HOMOLOGUÉ SELON

LES NORMES NATIONALES CANADIENNES ET AMÉRICAINES:CSA 22.2 NO. 46 UL 2021

FOYER À ÉLECTRIQUE. HOMOLOGUE POUR

INSTALLATION DANS UNE CHAMBRE A COUCHER, UNE

SALLE DE BAIN ET UN STUDIO. APPROPRIE POUR

INSTALLATION DANS UNE MAISON MOBILE.

ELECTRIC FIREPLACE. SUITABLE FOR BEDROOM

AND BED-SITTING ROOM INSTALLATION. SUITABLE

FOR MOBILE HOME INSTALLATION.

VOLTAGE: 120 VAC TENSION: 120VCA

FREQUENCY: 60Hz FRÉQUENCE: 60Hz

POWER: 1500W PUISSANCE: 1500W

DATE CODE: XXXXX CODE DE DATE:

DESIGNED IN NORTH AMERCIA

BY WOLF STEEL LTD.

MADE IN CHINA FABRIQUE EN CHINE

WOLF STEEL LTD.

24 NAPOLEON ROAD,

BARRIE, ON, L4M 0G8 CANADA

SERIAL NUMBER/NO. DE SERIE: NEFL

MODELS / MODÈLES

CEFL32FH

DESIGN AMERIQUE DE NORD

PAR WOLF STEEL LTD.

MASTER CONTRACT: 161746 CONTRAT-CADRE: 161746

NEFL32FH

NEFL42FH CEFL42FH

NEFL50FH CEFL50FH

CEFL60FH

NEFL60FH

NEFL72FH CEFL72FH

NEFL100FH CEFL100FH

SAMPLE

A 22.2 NO. 46 AND UL 202

.2 NO. 46 AND UL 202

RICAINES:CSA 22.2 NO. 46CSA 22.2 NO. 46

FOYER À ÉLECTRIQUEECTRIQU

INSTALLATION DANINSTALLATION DAN

SALLE DE BAIN ESALLE DE BAIN

INSTALLATIONINSTALLATIO

VOLTAGE:OLTAGE:

12

0

VA

C

120 VAC

FREQUENCY

:EQUENCY:

60Hz 60H

P

OWER

:OWER:

150 150

D

ATE CODE:

DATE CODE:

SIGNED IN NORTH AMNED IN NORTH A

BY WOLF SBY WOLF S

MA

D.D.

ROAD,

OAD

L4M 0G8 CANADA

M 0G8 CANADA

SAMPLE

P

PL

P

MODELS / MODÈLES MODELS / MODÈLE

CONTRAONTRA

M

H

50FH0FH

P

EN

W415-1542 / A / 10.06.15

8

!

WARNING

2.0 LOCATING APPLIANCE

2.1 GROUNDING APPLIANCE

DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF

TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS,

CLOTHES AND CURTAINS AT LEAST 36" FROM THE FRONT OF THE APPLIANCE.

NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER

WATER CONTAINER.

WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND

MAINTENANCE.

TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE ELECTRIC APPLIANCE

MUST NOT BE INSTALLED AGAINST VAPOR BARRIER OR EXPOSED INSULATION. LOCALIZED

OVERHEATING COULD OCCUR AND A FIRE COULD RESULT.

DO NOT EXPOSE THE ELECTRIC APPLIANCE TO THE ELEMENTS (SUCH AS RAIN, ETC.)

96.1

GROUNDING METHODS

METAL SCREW

(A)

NOT ALLOWED IN CANADA

GROUNDING

MEANS

ADAPTER

GROUNDING PIN

COVER OF

GROUNDED

OUTLET BOX

(C)

(B)

This appliance is for use on 120 volts. The cord has a plug

as shown in (A). An adapter as shown in (C) is available

for connecting three-blade grounding type plugs to two-slot

receptacles. The green grounding lug extending from the

adapter must be connected to a permanent ground such as

a properly grounded outlet box. The adapter should not be

used if a three-slot grounded receptacle is available.

To disconnect appliance, turn controls to off, then remove

plug from outlet.

EN

W415-1542 / A / 10.06.15

9

3.0 INSTALLATION

Your appliance is a wall-mounted, recessed and/or mantel installed appliance. Select a suitable location that is

not susceptible to moisture and is away from drapes, furniture and high trafﬁ c areas.

NOTE: Follow all National and local electrical codes.

!

WARNING

RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE CORD TO AVOID

TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY. DO NOT RUN

CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW RUGS, RUNNERS OR THE LIKE. ARRANGE CORD

AWAY FROM TRAFFIC AREAS AND WHERE IT WILL NOT BE TRIPPED OVER.

RISK OF FIRE! TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY MANNER. DO NOT

USE ON SOFT SURFACES WHERE OPENINGS MAY BECOME BLOCKED.

RISK OF FIRE! DO NOT BLOW OR PLACE INSULATION AGAINST THE APPLIANCE.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE APPROVED OPTIONAL ACCESSORIES.

USE OF OPTIONAL ACCESSORIES NOT SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE

WARRANTY AND/OR RESULT IN A SAFETY HAZARD.

IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT

CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

THIS APPLIANCE IS HEAVY. IT IS HIGHLY RECOMMENDED THAT TWO PEOPLE INSTALL THIS APPLIANCE.

HEATER VENTS ON THE ELECTRIC APPLIANCE CANNOT, IN ANY WAY, BE COVERED AS IT MAY CREATE A FIRE

HAZARD.

DO NOT RUN THE POWER CORD HORIZONTALLY, DIRECTLY BELOW THE APPLIANCE.

68.5A

3.1 MINIMUM CLEARANCE TO COMBUSTIBLES

Measurements are taken from the glass front.

Bottom 0" Top 8" (203mm) to mantel

Sides 0" Top 8" (203mm) to ceiling

Back 0"

SIDE VIEW

8" (203mm)

MANTEL

FLOOR

WALL

!

WARNING

WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE

HEAT RESISTANT TO PREVENT DISCOLOURATION.

3.2 MINIMUM MANTEL CLEARANCES

EN

W415-1542 / A / 10.06.15

10

Due to the many different materials used on different walls, it is highly

recommended that you consult your local builder before you install this

appliance on the wall.

A. Select a location that is not prone to moisture and is located at least

36" (914mm) away from combustible materials such as curtain

drapes, furniture, bedding, paper, etc.

B. Have two people hold the appliance against the wall to determine the

ﬁ nal location.

C. Place unit face down on a soft, non abbrasive surface. Remove the

bracket from the back of the unit by removing the screws, refer to

Figure 1.

D. Mark out location, then mount the bracket(s) onto the wall using the supplied screws. This bracket

MUST have the hooks facing upward and be level. NOTE: It is strongly recommended that the

mounting bracket be screwed

into the wall studs where

possible. If the wall studs

cannot be used, ensure that

the supplied plastic anchors

are used to afﬁ x the bracket

to the wall and the bracket is

adequately secured.

E. With the wall mounting bracket installed have two people lift the appliance up and insert the two hooks

on the bracket into the two slots on the back of the appliance.

F. Check the appliance for stability ensuring that the bracket will not pull free from the wall.

3.3 INSTALLING THE APPLIANCE ONTO THE WALL

HOOK

SCREWS

HOOK

SIDE VIEW

BODY

FLOOR

GLASS FRONT

21 5/8"

550mm

NEFL32/42/50FH BRACKET ILLUSTRATED

NEFL60/72/100FH BRACKET ILLUSTRATED

Measurements are taken from the body.

Sides, back and top 0"

5"

127mm

3 1/2"

89mm

MIN MAX

JUNCTION

A

B

A

B

Finishing Material

3.3.1 MINIMUM CLEARANCE TO COMBUSTIBLES

3.3.2 FRAMING

(NON-LOAD

BEARING)

EN

W415-1542 / A / 10.06.15

11

MODEL NO. A B

NEFL32FH 21" (535mm) 27 13/16" (707mm)

NEFL42FH 21" (535mm) 38" (965mm)

NEFL50FH 21" (535mm) 45 15/16" (1166mm)

NEFL60FH 21" (535mm) 55 13/16" (1418mm)

NEFL72FH 21" (535mm) 67 7/8" (1725mm)

NEFL100FH 21" (535mm) 95 7/8" (2435mm)

Due to the many different ﬁ nish materials used on walls, it is highly recommended that you consult your local

builder before you install this appliance in the wall.

Select a location that is not prone to moisture and is located at least 36" (914mm) away from combustible

materials such as curtain drapes, furniture, bedding, paper etc.

3.4 RECESSING THE APPLIANCE INTO THE WALL

A. Measure the appliance and create a rough in with electrical.

B. Remove the front glass, refer to "FRONT GLASS REMOVAL" section.

C. Hold the appliance up to ensure it will ﬁ t into the framing.

D. If the appliance is fully recessed into the wall:

• Bend the two top tabs upward on the front glass, Figure 4.

• Use the 6 screws (provided) to lock the appliance into the wall with the existing two side

ﬂ anges, see Figure 2.

• Install the media and reinstall the glass front.

E. If partial recess into the wall:

• Use the two mounting brackets (supplied) to lock the appliance to the wall, see Figure 3.

NOTE: Two sets of holes are provided for recessing into wall. The wall structure may

limit how far the appliance can be recessed. Use the appropriate set of holes when

recessing to the frame, it may be necessary to use the four holes on the top and

bottom.

NOTE: It is recommended the walls of the appliance enclosure be ﬁ nished (ie. drywall) to avoid

exposed insulation or vapour barrier coming in contact with the appliance. This will ensure clearance

to combustibles is maintained.

EN

W415-1542 / A / 10.06.15

12

NOTE: The appliance tabs come bent. You must bend the tab ﬂ at by hand when fully recessing the

appliance into the wall, Figure 4.

FIG. 4

3.4.1 INSTALLING THE APPLIANCE INTO A MANTEL

A. Remove the glass front, refer to "FRONT GLASS REMOVAL " section for removal instructions.

B. Install the rubber feet onto the bottom of the appliance for stability, refer to "RUBBER FEET

INSTALLATION" section for instructions.

C. Install the top and bottom brackets provided.

D. Insert the appliance into the mantel and secure it with the brackets or refer to "ELECTRIC

FIREPLACE MANTEL" installation manual for proper appliance installation instructions.

E. Place the crystal embers along the media tray, refer to "CRYSTAL EMBER INSTALLATION" section.

F. Reinstall the glass front.

EN

W415-1542 / A / 10.06.15

13

3.4.2 RUBBER FEET INSTALLATION

A. Place the appliance face down on a soft surface.

B. Using a screw driver, remove the screws on the bottom of the appliance.

C. Install the 4 rubber feet (6 rubber feet for NEFL60/72/100FH) onto the bottom of the appliance using

the screws from Step B, see below.

NOTE: The screws for installing the rubber feet are secured to the appliance. Removal of the screws is

necessary for installing the rubber feet.

NEFL32/42/50FH ILLUSTRATED

NEFL60/72/100FH ILLUSTRATED

EN

W415-1542 / A / 10.06.15

14

3.5 HARD WIRING INSTALLATION

HARD WIRING CONNECTION

If it is necessary to hard wire this appliance, a qualiﬁ ed electrician must remove the cord connection, and wire

the appliance directly to the house hold wiring.

This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. In

the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the

current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.

!

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE

PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

A. Remove the cover plate from the right side

bottom of the appliance by removing the three

screws, as shown above.

B. Remove the wire connectors from the power

cord. The power cord may be discarded.

C. Take the new cover plate, supplied in the hardware bag. Punch out the 7/8" (22.2mm) hole and install

a box connector through, into the junction box. Snap the box connector clamp onto the supply wires.

D. Using the wire connectors, connect the ground green wires (G), the common white wires (N)

together, then the hot black wires (L) and then the refer to Figure 3.

E. Reinstall the cover plate using the three screws, as shown in Figure 1.

Fig. 1 Fig. 2

COVER PLATE

G

NL

Fig. 3

EN

W415-1542 / A / 10.06.15

15

EN

W415-1542 / A / 10.06.15

16

4.0 FINISHING !

WARNING

POWER SUPPLY SERVICE MUST BE COMPLETED PRIOR TO FINISHING TO AVOID

RECONSTRUCTION.

HEAT VENTS AND AIR OPENINGS CANNOT BE COVERED IN ANY CIRCUMSTANCES.

4.1 FRONT GLASS INSTALLATION

!

WARNING

BEFORE THE FRONT GLASS IS INSTALLED OR REMOVED UNPLUG THE APPLIANCE AND WAIT

UNTIL APPLIANCE IS COOL TO THE TOUCH. GLASS CAN BE HEAVY AND FRAGILE SO HANDLE

WITH CARE. 75.1

FOR MODELS NEFL50/60/72/100FH ONLY:

A. Before installing the front glass, remove the screws securing the paper board on the inside of the

appliance that protects the control panel. Discard the paper board.

B. Reinstall the screws,see Figure 1. (For recessed installed appliances only)

C. Remove the 2 screws from the top of the appliance.

D. Have two people, lift the glass up and away from the appliance, holding the glass vertical not ﬂ at while

carrying. Place the glass face down onto a soft, non-abrasive surface, careful not to ﬂ ex the glass.

E. Bend the top tabs ﬂ at, see Figure 2

F. Install the crystal embers, refer to "CRYSTAL EMBER INSTALLATION" section.

G. Install the front glass by aligning with the pins on the appliance. Press the glass in and down to

securely engage with the brackets. It must be fully engaged to ensure the touch display panel

performs properly.

H. Secure the front glass using the screws provided to the top of the appliance, see Figure 3.(If fully

recessed this is not necessary)

Paper Paper

FIG. 1

FIG. 2

EN

W415-1542 / A / 10.06.15

17

FIG. 3

The glass front must be removed and the appliance must be secured in its ﬁ nal location before the crystal

embers are installed.

A. Carefully place crystal embers into the bottom media tray on the

front of the appliance as illustrated. Apply an even layer from side to

side.

A. Remove the 2 screws from the top of the appliance, as shown below.

B. Have two people, lift the glass up and away from the appliance, holding the glass vertical not ﬂ at while

carrying. Place the glass face down onto a soft, non-abrasive surface, careful not to ﬂ ex the glass.

C. Install the crystal embers, refer to "CRYSTAL EMBER INSTALLATION" section. Install the front glass

by aligning with the pins on the appliance. This ensures the touch display panel performs properly.

FOR WALL MOUNT, PARTIAL RECESS AND MANTEL INSTALLED APPLIANCE ONLY:

4.2 FRONT GLASS REMOVAL

4.3 CRYSTAL EMBER INSTALLATION

EN

W415-1542 / A / 10.06.15

18

5.0 OPERATING INSTRUCTIONS

Once the appliance has been plugged into a grounded electrical outlet, it is ready to operate.

NOTE: Ensure the house circuit breakers for the power supply are turned on. In the event of a power

failure, the appliance will lose its memory function and will reset to factory mode when the power

returns.

The Main Power button is located on the front bottom right side of the appliance.

5.1 MAIN POWER BUTTON

5.2 OPERATING TOUCH DISPLAY PANEL AND REMOTE CONTROL

POWER Turns the appliance ON/OFF.

FLAME - ORANGE

FLAME - BLUE

TIMER

TEMPERATURE

Controls Orange Flame brightness.

6 Settings: ( F5-F4-F3-F2-F1-F0 ) Flame dims from F5 to F1.

F5 is the brightest setting and F0 is off.

Controls Blue Flame brightness.

6 Settings: ( F5-F4-F3-F2-F1-F0 ) Flame dims from F5 to F1.

F5 is the brightest setting and F0 is off..

Controls the Timer.

9 Settings: (0.5h, 1h, 2h, 3h, 4h, 5h, 6h, 7h, 8h) Press button

until reach desired setting.

HEATER Controls the Heater.

Press button to initiate the heater.

(H0) no heater or blower.

(BL) blower only.

(H1), heater blows warm air (750W)

(H2), heater blows hot air (1500W)

NOTE: Heater functions cycle from H0-BL-H1-H2, Press

and hold the heater button for 5s, the heater and

temperature setting will be locked onto the selected

setting. Hold the button for 5s again, the heater will be

unlocked.

Press and hold the button for 5 seconds. This will change the

display, from °C to °F or vice versa.

11 Settings: (64°F, 66°F, 68°F, 70°F, 72°F, 74°F, 76°F, 78°F,

80°F, 82°F and OFF) / (17°C, 19°C, 20°C, 21°C, 22°C, 23°C,

24°C, 26°C, 27°C, 28°C and OFF)

!

WARNING

WHILE THE APPLIANCE IS OPERATING DO NOT REMOVE THE GLASS PANEL. THIS WILL CAUSE

THE REMOTE CONTROL AND TOUCH PANEL TO DISFUNCTION.

The touch display panel is shown by LED's on the front bottom right of the appliance. The LED's will

disappear after 10 seconds of no function change. The Main Power button will be dim.

WARNING: Do not move or remove the glass panel, when the appliance is plugged in and operating.

This will cause the remote control and touch panel to no longer function.

EN

W415-1542 / A / 10.06.15

19

6.0 MAINTENANCE

!

WARNING

PREPARATION FOR MAINTENANCE

ALWAYS DISCONNECT THE POWER AND ALLOW THE ELECTRIC APPLIANCE TO COOL BEFORE

PERFORMING ANY CLEANING, MAINTENANCE OR RELOCATION OF THIS ELECTRIC APPLIANCE.

TURN CONTROLS TO OFF AND REMOVE PLUG FROM OUTLET OR TURN OFF THE HOUSE

CIRCUIT BREAKER TO ELECTRIC APPLIANCE RECEPTACLE.

DO NOT INSTALL REPLACEMENT LAMPS THAT EXCEED SPECIFIED MAXIMUM WATTS.

THE HALOGEN LAMPS IN YOUR APPLIANCE CAN BECOME EXTREMELY HOT. ALLOW AT LEAST

10 MINUTES BETWEEN TURNING OFF THE APPLIANCE AND REMOVING THE LAMPS TO AVOID

ACCIDENTAL BURNS.

DO NOT HANDLE THE LAMP WITH BARE FINGERS, OILS FROM YOUR SKIN WILL DAMAGE THE

LAMPS WHEY THEY HEAT UP. USE GLOVES OR A CLEAN DRY CLOTH WHEN HANDLING LAMPS.

6.1 REMOTE BATTERY INSTALLATION

1. To replace the existing battery remove the

battery holder.

2. To remove the battery holder turn remote onto

rear side and press the left side leaver towards

the center while pulling the battery holder out

using the slot provided.

3. Replace existing battery, type CR 2025, with a

new battery and reinstall the battery holder into

the remote by sliding it into position, as shown.

REMOTE

(REAR SIDE)

BATTERY HOLDER

BATTERY (CR 2025)

NOTE: The remote control must remain within 5 meters or 17 feet of the appliance to be effective, this

range may be reduced when battery power is depleted.

NOTE: The remote control has a removable plastic tab to prolong the battery life while shipping,

remove the tab for the remote control to function.

EN

W415-1542 / A / 10.06.15

20

7.0 WIRING DIAGRAM

!

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE

PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

La page charge ...

NAPOLEON Allure NEFL60FH Installation And Operating Instructions Manual

NAPOLEON Allure NEFL60FH Installation And Operating Instructions Manual

dans d''autres langues

Documents connexes

Autres documents